View
5
Download
0
Category
Preview:
Citation preview
Research ArticleNumerical Investigation of Acoustic Emission Events ofArgillaceous Sandstones under Confining Pressure
Zhaohui Chong,1,2 Xuehua Li,1 Jingzheng Lu,1 Tian Chen,1 Ji Zhang,3 and Xiangyu Chen1
1Key Laboratory of Deep Coal Resource Mining, Ministry of Education of China, School of Mines,China University of Mining and Technology, Xuzhou, Jiangsu 221116, China2Faculty of Engineering and Information Sciences, University of Wollongong, Wollongong, NSW 2522, Australia3Beijing Computational Science Research Center, China Academy of Engineering Physics, Beijing 100193, China
Correspondence should be addressed to Zhaohui Chong; chongcumt@126.com and Xuehua Li; xuehua_cumt@163.com
Received 19 December 2016; Accepted 16 February 2017; Published 27 March 2017
Academic Editor: Fabrizio Greco
Copyright ยฉ 2017 Zhaohui Chong et al.This is an open access article distributed under the Creative CommonsAttribution License,which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
At the laboratory scale, locating acoustic emission (AE) events is a comparatively mature method for evaluating cracks in rockmaterials, and themethod plays an important role in numerical simulations.This study is aimed at developing a quantitativemethodfor the measurement of acoustic emission (AE) events in numerical simulations. Furthermore, this method was applied to estimatethe crack initiation, propagation, and coalescence in rock materials.The discrete element method-acoustic emission model (DEM-AE model) was developed using an independent subprogram. This model was designed to calculate the scalar seismic tensor ofparticles in the process of movement and further to determine the magnitude of AE events. An algorithm for identifying the samespatiotemporal AE event is being presented. To validate the model, a systematic physical experiment and numerical simulation forargillaceous sandstones were performed to present a quantitative comparison of the results with confining pressure. The resultsshowed good agreement in terms of magnitude and spatiotemporal evolution between the simulation and the physical experiment.Finally, the magnitude of AE events was analyzed, and the relationship between AE events and microcracks was discussed. Thismodel can provide the research basis for preventing seismic hazards caused by underground coal mining.
1. Introduction
An increasing number of underground engineering andphysical experiments have focused on investigating the fail-ure or fracture properties of rocks [1, 2]. An understanding ofthe characteristics of AE in the process of crack propagationin rock materials helps to prevent underground engineeringhazards, such as rock burst [3, 4], mining tremor [5], roadwayrib spalling [6], and similar events. AE signals can be trig-gered when distortions in rock materials occur, such asgeneration of microcracks [7], pore closing or collapse [8],or fault sliding [9, 10]. Traditional rock deformation detectors(e.g., strain gauges) are only able to detect the overalldeformation of rocks. Along with the improvement of exper-imental conditions, modern laboratory techniques allow forthe detection of microcracks or local macroscopic fractures[11].
Among the numerical methods that have been used tostudy the deformation and cracks in rock materials, the finiteelement method (FEM) or Fast Lagrangian Analysis of Con-tinua (FLAC) cannot generate actual cracks, and themajorityof investigations have focused mainly on studying the plasticor damaged zones [12, 13]. The DEM can generate actualcracks and identify the types of cracks [14, 15], but few studieshave used this method to perform a quantitative analysis ofthe magnitude and location of the crack source. Althoughthe detection of AE events during the deformation processin rock materials is a powerful tool for the quantitativeanalysis of cracks, the AE characteristics cannot be deriveddirectly from numerical simulations [16], and therefore anew module using an independent subprogram is needed.Several researchers have contributed to the monitoring of AEevents using numerical simulations. Based on the FEM/DEMmethod, Lisjak et al. [17] proposed a new model to simulate
HindawiMathematical Problems in EngineeringVolume 2017, Article ID 7676417, 16 pageshttps://doi.org/10.1155/2017/7676417
https://doi.org/10.1155/2017/7676417
2 Mathematical Problems in Engineering
Ball
Bond
mod
el
Con
tact
mod
el
Das
hpot
Ball or wall
Contact bond
Unbond
Parallel bond
Normaldirection
Sheardirection
kn
ks
Particle A
Particle BParticle A
Particle B
(b) (c)(a)
Particle A
Particle BL
Figure 1: A parallel bond in PFC. (a) Components of a contact. (b) Parallel bond model. (c) Schematic of constitutive law of contact forcesat the interface between two particles.
microseismic events, which described the fracture process inrock materials using three parameters:๐ท-value, AE rate, and๐-value. Heinze et al. [18] developed a poroelastoplastic con-tinuummodel, which divided and quantified rock failure intoa prefailure stage, a massive failure stage, and a macroscopicfailure stage. Through sensitivity analysis, Tang et al. [19,20] evaluated the strength and fracture processes of rockmaterials and applied the Weibull distribution rule of AEevents to detect rock fractures and deformations.
In DEM, if each generated microcrack is considered anindividual AE event, themagnitude of theAE event caused bythe hypocenter of microcrack inversion is almost the samefor each event. At the laboratory scale or at the field scale, themagnitude of AE events is generally in line with the expo-nential distribution [17]. Therefore, most previous studieshave been unable to describe the spatiotemporal distribution,magnitude, and other behaviors of AE events simultaneously.Deformation and slip of rocks can cause quick release ofenergy and indicate the initiation, propagation, and coales-cence of cracks as well [21]. The seismic moment can be usedto represent the magnitude of the seismic source [22], whichcan be obtained from AE monitoring. Thus, in DEM, themagnitude of the seismic source can be determined bycalculating the particle moment tensor, thereby establishinga natural congruent relationship between AE events andoccurrence of microcracks.
Because the stress and movement of unit particles arealready known, in this study, a new module was developedincorporating an independent subprogram to calculate themoment tensor of rock materials as cracks developed, so thatthe magnitude of AE events could be established. An algo-rithm for identifying the same spatiotemporal AE event wasdeveloped. This new model was defined as the DEM-AEmodel. Physical experiments were conducted for a quanti-tative analysis of the spatiotemporal relationship of the AEevents as cracks were generated in argillaceous sandstonesunder different confining pressures. A validation analysis wasperformed on themodel. A comparison of themagnitude andspatiotemporal relationship of AE events in the numericalsimulations and the physical experiments demonstrated thatthe simulations were in good agreement with the exper-imental data. Finally, in this study, we also analyzed the
magnitude of AE events under different confining pressuresin numerical simulations and discussed the relationshipbetween AE events and the number of microcracks.
2. Simulation Mechanism for Using PFC
A common representation of an explicit DEM is the ParticleFlowCode (PFC). PFC theory assumes thatmacroscopic rockmaterials are composed of many bonded microscopic parti-cles, which is a mechanical behavior of representing macro-scopic rock materials by the relative motion of micro-scopic particles [23, 24]. PFC has the following advantages:(1) it overcomes the theoretical assumption of traditionalcontinuum-based models [14] and (2) PFC is more suitablefor simulating nonlinear deformation in rock materials andfor detecting the number and evolution of cracks [25]. Twobondmodels are proposed based on the type of bond betweenparticles. Based on previous work, the parallel bond model(PBM) was deemed more suitable for simulation of rockmaterials [26, 27]. A simulation of the basic mechanicalbehaviors of rock materials through PBM is shown in Fig-ure 1.
2.1. Governing Equation of Crack Generation. In PBM, themovement of particles causes changes in force and moment.The resultant force and moment can be divided into normal-and shear-directed components, which can be expressed asfollows:
๐น๐ = ๐นn๐๐ + ๐นs๐ก๐,๐๐ = ๐n๐๐ +๐s๐ก๐,
(1)
where๐น๐,๐นn, and๐นs are the total, normal-, and shear-directedforce of the parallel bond, respectively;๐๐,๐n, and๐s arethe total, normal-, and shear-directed moment of the parallelbond, respectively; ๐๐ and ๐ก๐ are the normal- and shear-directed unit vectors, respectively.
๐น๐ and๐๐ are initialized as 0. Each subsequent related dis-placement and rotation will create an increment in elasticforce and moment that is added to the current value. The
Mathematical Problems in Engineering 3
Bond break
Breakage by tension
TensionOverlap Un
Overlap Un
Particles separate1
1
Compression
c (tensile)
kn
kn
(a)
1
Particles sliding
Breakage byshear
Shear
Frictional slidingRotation
ks
c (shear)
(b)
Figure 2: The interparticle bond breaks and the corresponding mechanical behaviors. (a) Normal component of bond breaks. (b) Shearcomponent of bond breaks.
(b)(a)
Parallel bond
Bondstiffness
stiffness
ฮF2
ฮF1
L2L1
Contact
Microcrack
Tensilecomponent
Compression component
Figure 3: AE event with one microcrack. (a) Stress schematic of the particles after generation of the microcrack. (b) Calculation chart ofseismic moment tensor.
t
x
Excitation time 2
Excitation time 3Excitation time 4
Excitation time 5Overall excitation time (T0)
Crack 3
Crack 1Crack 2
Crack 4
Crack 5
Excitation time 1 (T1)(T2)
(T3)(T4)
(T5)
Figure 4: Definition of the same AE event in terms of time; the occurrence order of microcracks is Cracks 1, 5, 2, 3, and 4, in which Cracks1, 2, and 3 belong to the same AE event.
4 Mathematical Problems in Engineering
Crack 3
Ra
B
EF
ACrack 1
Crack 2
Crack 4
Crack 5
C
D
Parallel bond
CCCCrack 3C
Ra
B
E
ACrackkkkkkkkkkkkkkk 11
Crackkkk 2
Crack 444
C
D
Figure 5: Definition of the same AE event in terms of space, in which Cracks 1, 2, and 3 belong to the same AE event.
increment in elastic force andmoment is calculated accordingto
ฮ๐นn = ๐n๐ดฮ๐n,ฮ๐นs = โ๐s๐ดฮ๐s,ฮ๐n = โ๐s๐ผฮ๐n,ฮ๐s = โ๐n๐ผฮ๐s,
(2)
where ฮ๐นn and ฮ๐นs are the increments of the normal- andshear-directed force, respectively; ๐n and ๐s are the contactnormal stiffness and shear stiffness, respectively; ฮ๐n and๐sare the increments of the elastic force that is added to thecurrent value, respectively;ฮ๐n andฮ๐s are the incrementsof the normal- and shear-directed moment, respectively; ๐nand ๐s are the increments of the rotational angle that is addedto the current value, respectively.
Other parameters ๐ด, ๐ผ, and ๐ฝ are the area, moment ofinertia, and polarmoment of inertia of the parallel bond crosssection, respectively, which are determined based on
๐ด = 2๐ ๐ก,๐ผ = 23๐ 3๐ก,๐ฝ = ๐๐ด.
(3)
In PBM, the maximum tension and shear stress betweenparticles are subject to
๐max = โ๐นn๐ด +๐s ๐ ๐ผ ,
๐max =๐นs๐ด +
๐n ๐ ๐ฝ .(4)
The radius of the cross section is described by
๐ = ๐min (๐ ๐ด, ๐ ๐ต) , (5)
where ๐ is a radiusmultiplier (usually equal to 1.0),๐ ๐ด and๐ ๐ตare the radii ofA and B, respectively (Figure 5), and ๐max and๐max are the tensile strength and shear strength, respectively.
In the normal and shear direction, the relationshipbetween stress and displacement of the contact pointsdepends on ๐n and ๐s, respectively [28]. According to Fig-ure 2, the contact behavior of normal stress ๐๐ and displace-ment ๐ข๐ can be described as follows:
๐๐ = โ๐n๐ข๐. (6)If โ๐๐ > ๐max, then ๐๐ = ๐๐๐ = 0. At this point, tensile
microcracks develop, marked with a red short line. ๐๐๐ is theresidual tensile strength.
The contact behavior of shear stress ๐๐ can be describedas follows:
๐๐ = ๐s๐ข๐ ,๐max = ๐ + ๐๐ tan๐, (7)
where ๐ข๐ is the shear displacement, ๐ and ๐ are the cohesivestrength and friction angle, respectively, and ฮ๐ข๐๐ and ฮ๐ข๐ are the elastic and total component of the incremental sheardisplacement, respectively.
If |๐๐ | โค ๐max, then ฮ๐๐ = โ๐๐ ฮ๐ข๐๐ ; or else, if |๐๐ | > ๐max,then ๐๐ = sign(ฮ๐ข๐ ) โ ๐max. The โsignโ function here is amathematical symbol that allows ๐๐ to be positive. At thispoint, shear microcracks develop, marked with a blue shortline.
2.2. Algorithm of AE Events in DEM
2.2.1. Principle of Calculating the Magnitude of AE Events.Due to the growth of new cracks, friction motion in rockmaterials will create AE signals. At the laboratory scale, inorder to estimate the damage zone and the crack location of
Mathematical Problems in Engineering 5
rocks, signal monitoring is generally carried out by using anAE instrument [29, 30]. At the field scale, a microseismo-graph is commonly used for monitoring the fracture zoneaffected by the excavation of underground chambers as wellas rock burst [31]. As formonitoring of the seismic source, AEevents andmicroseismic events have similar mechanisms buta different range of frequencies and both events often precedeor accompany cracks during the detection process [16, 32]. Inorder to conduct a quantitative analysis of the seismic source,namely, to detect the magnitude and location of AE events,the seismic moment is often utilized as the basic approach.
The scalar seismic moment is defined as
๐0 = ๐บ โ ๐ด โ ๐ข, (8)where ๐0 is the scalar seismic moment; ๐บ is the shearmodulus; ๐ข is the current displacement in the calculation.
InDEM, since the stress andmovement of particles can bederived directly from calculations, it is easier to determine thescalar seismic moment based on the change of contact forcebetween particles as new cracks develop. As shown in Fig-ure 3, particles at both sides of the newmicrocrack are definedas source particles (Particles A and B). After the growthof new microcracks, the contact force changes due to themovement of source particles. If the event is composedof a single microcrack, its zone of action centers on themicrocrack, and the radius of the affected zone is the diameterof the bigger source particle (see Figure 5). If the AE event iscomposed of several microcracks, the geometric center of allthe microcracks will be the spatial position of the AE event.In this way, the seismic moment tensor in DEM is thesummation of all the variables and their quantity of contactforces multiplied by the corresponding arm of the force (thedistance between the location of the contact point and thecenter of the microcrack):
๐๐๐ = โ๐
(ฮ๐น๐๐ฟ๐) , (9)where ๐๐๐ is the scalar seismic moment in the calculation;ฮ๐น๐ and ๐ฟ๐ are the ๐th component of the contact force and thecorresponding arm of the force.
The maximum scalar moment of the moment tensor is
๐0 = โโ๐๐=1๐๐๐22 . (10)
The magnitude of AE events is calculated as per theempirical equation
๐ = 23 lg (๐0) โ 6, (11)where๐ is the magnitude of AE events.2.2.2. Algorithm for Identifying Space and Time of AE Events.Only when new cracks occur at other contact points of thesource particles (Particles A and B) are they likely to be thesame AE event, because the stress in DEM can be transferredto other adjacent particles. The zone affected by the AE
Figure 6: Preparing the physical specimens.
(2)(3) (4)
(6)
Stress-time data acquisition system
Pressurechamber
(1)
(5)
(7)
AE data acquisitionsystem
Hydraulicpower pack
Hydraulicpower pack
zy
x
Figure 7: Schematic diagram of the two data acquisition proceduresunder uniaxial compression. (1) Stress-strain control microcom-puter. (2) Loading system. (3) Specimen. (4) Acoustic emissionsensor. (5) AE control microcomputer. (6) Signal amplifier. (7) Datatransmission line.
event will also extend gradually along with the coalescenceof cracks.
The definition of excitation time of an AE event is shownin Figure 4. Since the propagation velocity of the crack istwo times as fast as the shear wave velocity of rocks [33],the excitation time and affected area of the unit particles canbe calculated. Assuming that the excitation time of Crack 1for spreading to the boundary of its affected area is ๐1 (seeFigure 5), the calculation of the moment tensor is updatedfor each time step within the period of ๐1. If no new cracksoccur within๐1 or within the affected area of Crack 1, this AEevent contains only one microcrack, and the total excitationtime is ๐1. On the contrary, if Crack 2 (its excitation time forspreading to the boundary of the affected area is ๐2) developsboth within ๐1 and within the affected area of Crack 1, theaffected area of this AE event will be superposed on theaffected area of Crack 2, and the total excitation time is ๐0. Byanalogy, if Crack 3 comes into being within ๐0, the affectedarea and magnitude will also be superposed. As for thisAE event in Figures 4 and 5, its affected area is the superpo-sition of the action ranges of Cracks 1, 2, and 3, and its totalexcitation time is ๐0.
6 Mathematical Problems in Engineering
Table 1: Test results for the specimens.
Specimen number ๐3 ๐๐ก (๐1 โ ๐3) ๐ธslope ]I-1 0.5 19.55 20.11 0.194II-1 0.5 18.86 20.70 0.216III-1 0.5 18.23 21.67 0.235I-2 2.0 20.97 20.64 0.204II-2 2.0 21.02 19.87 0.174III-2 2.0 20.14 20.24 0.210I-3 4.0 24.60 22.16 0.224II-3 4.0 25.47 21.25 0.195III-3 4.0 24.31 22.04 0.203I-4 6.0 29.08 21.88 0.201II-4 6.0 30.35 22.87 0.214III-4 6.0 29.67 21.41 0.224Note. ๐1: principal stress; ๐3: confining pressure; ๐๐ก: peak deviatoric stress; ๐ธslope: Youngโs modulus; ]: Poissonโs ratio.
Experimental dataFitting curve of experimental data95% confidence interval
y = 1.99x 17.30
R2 = 0.9677
1 2 3 4 5 6 7 80Confining pressure (MPa)
15
20
25
30
35+
Friction angle = 19.36โ
Cohesion = 6.13 MPa
1โ3
(MPa
)
(a)
Experimental dataAverage data
Average = 21.34
0
5
10
15
20
25
30
Youn
gโ m
odul
us (G
Pa)
1 2 3 4 5 6 7 80Confining pressure (MPa)
= 0.15SD
(b)
Figure 8: Test results versus confining pressure for all specimens. (a) Deviatoric stress (๐1 โ ๐3). (b) Youngโ modulus.
As shown in Figures 4 and 5, even if Crack 4 comes intobeing within the affected area of Crack 1 in terms of space, theexcitation time for the development of Crack 4 is after ๐0, soCrack 4 andCrack 1 cannot be regarded as the sameAE event.The excitation time when Crack 5 occurs is within ๐0, but thelocation where Crack 5 occurs is not within the affected areaof Crack 1, so Crack 5 and Crack 1 cannot be regarded as thesame AE event, either.
3. Laboratory Tests
3.1. Experimental Procedure. The rock materials used inthis study were argillaceous sandstones from the ShanxiFormation at Shanxi Province, China, created to ๐50 ร100mm standard specimens with the core drilled as per theInternational Society for Rock Mechanics (ISRM) standard
(see Figure 6). The specimens were divided into four groupsfor the confined compression pressure tests of 0.5, 2.0, 4.0,and 6.0MPa. Both the upper face and the lower face of thespecimens were carefully polished and flatted.
As illustrated in Figure 7, the physical compression testwith confining pressure was performed on a universal servo-control testing machine (MTS815.02, America) by imposinga constant speed of 0.2mm/min until the ultimate failure ofthe specimens. The AE system was utilized to detect themagnitude and location of AE events. In this study, theAE system was composed of six commercially availablepiezoelectric sensors (Physical Acoustic Corporation type-Nano30), preamplifiers, and aMISTRASMicro-II Digital AEdata acquisition system. The AE sensors were attached to thesurface of the hydraulic cylinder using a coupling agent andwere further fixed to record AE events data of the specimens
Mathematical Problems in Engineering 7
Table 2: Microscopic parameters of the simulated specimen after calibration.
Microparameters Symbol Unit ValueThe minimum particle radius ๐ min mm 1.0Ratio of maximum and minimum particle radius ๐ max/๐ min / 1.67Particle density ๐ kg/m3 2800Particle friction coefficient ๐ / 0.55Youngโs modulus of the particle ๐ธ GPa 14.4Parallel bond radius multiplier ๐ / 1.0Youngโs modulus of the parallel bond ๐ธ๐ MPa 14.4Normal stiffness of the parallel bond (mean) ๐๐-mean MPa 14.7Normal stiffness of the parallel bond (std. deviation) ๐๐-dev MPa 3.6Shear stiffness of the parallel bond (mean) ๐๐ -mean MPa 9.2Shear stiffness of the parallel bond (std. deviation) ๐๐ -dev MPa 2.4
Experimental curves Modelled curvesStress-strainRCAE-RAS
Relative axial strain (RAS) (%)
Stress-strainRCAE-RAS
0
4
8
12
16
200 20 40 60 80 100 120
0
20
40
60
80
100
120
0.4 0.8 1.2 1.6 2.00.0Axial strain/10โ3
Ratio
of c
umul
ativ
e AE
even
ts (R
CAE)
(%)
1โ3
(MPa
)
(a)
Experimental curvesStress-strainRCAE-RAS
Stress-strainRCAE-RAS
120120
0.5 1.0 1.5 2.0 2.5 3.00.0Axial strain/10โ3
0 20 40 60 80 100Relative axial strain (RAS) (%)
0
20
40
60
80
100
0
5
10
15
20
25
Ratio
of c
umul
ativ
e AE
even
ts (R
CAE)
(%)
1โ3
(MPa
)
Modelled curves
(b)
Experimental curves Modelled curvesStress-strainRCAE-RAS
Stress-strainRCAE-RAS
120120
0.5 1.0 1.5 2.0 2.5 3.00.0Axial strain/10โ3
0
6
12
18
24
300 20 40 60 80 100
Relative axial strain (RAS) (%)
0
20
40
60
80
100
Ratio
of c
umul
ativ
e AE
even
ts (R
CAE)
(%)
1โ3
(MPa
)
(c)
Experimental curves Modelled curvesStress-strainRCAE-RAS
Stress-strainRCAE-RAS
120120
0
6
12
18
24
30
0.8 1.6 2.4 3.2 4.00.0Axial strain/10โ3
0 20 40 60 80 100Relative axial strain (RAS) (%)
0
20
40
60
80Ra
tio o
f cum
ulat
ive A
E ev
ents
(RCA
E) (%
)
1โ3
(MPa
)
(d)
Figure 9: Deviatoric stress and ratio of cumulative events during confined compression test. (a) 0.5MPa; (b) 2.0MPa; (c) 4.0MPa; (d)6.0MPa.
8 Mathematical Problems in Engineering
Con
finin
g pr
essu
re (M
Pa)
Experimentalresults
Macroscopicfailure mode
Microscopicfailure mode
AE events mode
0.5
2.0
4.0
6.0
โ6.775โ6.750โ6.500โ6.250โ6.000โ5.750โ5.500โ5.250โ5.000โ4.750โ4.500โ4.250โ4.000โ3.750โ3.500โ3.250โ3.236
โ7.172โ7.000โ6.750โ6.500โ6.250โ6.000โ5.750โ5.500โ5.250โ5.000โ4.750โ4.500โ4.250โ4.000โ3.750โ3.500โ3.250โ3.000โ2.847
โ7.000โ6.750โ6.500โ6.250โ6.000โ5.750โ5.500โ5.250โ5.000โ4.750โ4.500โ4.250โ4.000โ3.750โ3.500โ3.250โ3.000
โ7.317โ7.250
โ2.795
โ7.000โ6.750โ6.500โ6.250โ6.000โ5.750โ5.500โ5.250โ5.000โ4.750โ4.500โ4.250โ4.000โ3.750โ3.500โ3.250โ3.000
โ7.396โ7.250
โ2.989
Figure 10: Comparison of failure modes between experiments and DEM simulations.
Mathematical Problems in Engineering 9
Confining pressure (MPa)
Shear crackTensile crack
6.04.02.00.50.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
Num
ber o
f cra
cks/ร10
3
Figure 11: Statistical quantity of microcracks under different confining pressures.
Expe
rimen
tal r
esul
tsM
odel
led
resu
lts
โ6.775โ6.750โ6.500โ6.250โ6.000โ5.750โ5.500โ5.250โ5.000โ4.750โ4.500โ4.250โ4.000โ3.750โ3.500โ3.250โ3.236
50% peak deviator stress
Peak deviator stress 90% postpeakdeviator stress
78% postpeakdeviator stress
Figure 12: Comparison of spatial AE events between experiments and DEM simulations at a confining pressure of 0.5MPa.
10 Mathematical Problems in Engineering
50% peak deviator stress
Peak deviator stress 90% postpeakdeviator stress
78% postpeakdeviator stress
Expe
rimen
tal r
esul
tsM
odel
led
resu
lts
โ6.750โ6.500โ6.250โ6.000
โ7.000โ7.172
โ5.750โ5.500โ5.250โ5.000โ4.750โ4.500โ4.250โ4.000โ3.750โ3.500โ3.250โ3.000โ2.847
Figure 13: Comparison of spatial AE events between experiments and DEM simulations at a confining pressure of 2.0MPa.
constantly. If the coordinates of specimens were as shown inFigure 7, the sensor coordinates were (25, 0, 20), (โ25, 0, 20),(12.5, โ21.65, 50), (โ12.5, 21.65, 50), (12.5, โ21.65, 80), and(โ12.5, 21.65, 80) with the unit in mm. The AE recordthreshold was set to 40 dB in order to avoid the possibility ofenvironmental disturbance. Both the servo-control testingmachine and the AE system were executed simultaneously toobtain the correlation of mechanical behavior and AE signalsof specimens.
Table 1 lists the experimental results for all the specimens.As for each group of specimens, the lateral pressure andcorresponding peak deviatoric stress were obtained by linearregression, as shown in Figure 8.The gradient ๐ and intercept๐ of the ๐ฆ-axis were used for the calculation of cohesion cand internal friction angle๐, with the calculation equations asfollows [34]:
๐ = arcsin ๐ โ 1๐ + 1 , (12)๐ = ๐1 โ sin๐2 cos๐ . (13)
According to Table 1 and Figure 8, Youngโs modulusshowed almost no change in increment as the confiningpressure increased from 0.5MPa to 6MPa, and the averageYoung modulus was 21.34GPa. Regarding the calculationresults of (11) and (12), the internal friction angle was 19.36โ,and the cohesion was 6.13MPa.
3.2. Calibration of Micromechanical Parameters. The discreteelement model must be calibrated to the associated micro-scopic parameters in order to describe the macroscopicmechanical behaviors of rock materials (i.e., deviatoric stressand Youngโs modulus). Although the calculation equationsfor parameters such as cohesion, stiffness, and friction angleare included in the manual of the PFC software [35], there isno fixed theory that validates the microscopic parameters ofrock materials [27].Therefore, in order to validate the model,the following steps were adopted for parameter calibration:
(1) Youngโs modulus and strength parameters (i.e., cohe-sion and internal friction angle) were calibratedfirst. The calibration standard was subjected to thecohesion and the internal friction angle obtainedfrom physical experiments, rather than using only the
Mathematical Problems in Engineering 11
50% peak deviator stress
Peak deviator stress 90% postpeakdeviator stress
78% postpeakdeviator stress
Expe
rimen
tal r
esul
tsM
odel
led
resu
lts
โ7.000โ6.750โ6.500โ6.250โ6.000โ5.750โ5.500โ5.250โ5.000โ4.750โ4.500โ4.250โ4.000โ3.750โ3.500โ3.250โ3.000
โ7.317โ7.250
โ2.795
Figure 14: Comparison of spatial AE events between experiments and DEM simulations at a confining pressure of 4.0MPa.
uniaxial compressive strength of argillaceous sand-stones as the basis.
(2) Initial microscopic properties were assigned in accor-dance with the relationship between microscopicparameters andmacroscopicmechanical behaviors ofrock materials.
(3) In the DEM, a servo systemwas used for compressiontestswith the confining pressure set at 0.5, 2.0, 4.0, and6.0MPa, respectively. In this case, trial and error wasapplied to determine microscopic parameters, untilYoungโs modulus reached 21.34GPa and the peakdeviatoric stresswas roughly consistentwith the enve-lope line resulting from physical experiments. Micro-scopic parameters of argillaceous sandstones aftercalibration are shown in Table 2, and the deviatoricstress-strain curve of different confining pressures isdisplayed in Figure 8.
(4) The established DEM-AE model was compared withthe results of the physical experiment (mainly includ-ing the spatiotemporal location of AE events andmagnitude), and the comparison results are presentedin Section 4.
4. Results and Discussion
4.1. Time Distribution of AE Events. After ensuring thatthe macroscopic parameters of the argillaceous sandstonespecimens in the physical experiments were consistent withthose of the numerical simulations, the contrastive analysisof the DEM-AE model was carried out. Figure 9 shows thecomparison ofAE events for the physical experiments and theDEM-AE model, in which the ๐ฅ-axis represents the relativeaxial strain and the ๐ฆ-axis represents the ratio of cumulativeAE events.
Under the different confining pressures, the resultsshowed good agreement for the ratio of cumulative AE eventsin the physical experiments and in the DEM-AE model. It isworth noting that, in the physical experiment, cumulative AEevents demonstrated linear growth at the initial loading stage;therefore, AE events could be detected even at this loadingstage in the physical experiment, causing deviation from thenumerical simulation. The detailed reasons are described inSection 4.4.
With the different confining pressures, the number of AEevents prior to loading to the peak deviatoric stress was verysmall, especially in the numerical simulation. There were
12 Mathematical Problems in Engineering
Expe
rimen
tal r
esul
tsM
odel
led
resu
lts
โ7.000โ6.750โ6.500โ6.250โ6.000โ5.750โ5.500โ5.250โ5.000โ4.750โ4.500โ4.250โ4.000โ3.750โ3.500โ3.250โ3.000
โ7.396โ7.250
โ2.989
50% peak deviator stress
Peak deviator stress 90% postpeakdeviator stress
78% postpeakdeviator stress
Figure 15: Comparison of spatial AE events between experiments and DEM simulations at a confining pressure of 6.0MPa.
nearly no AE events at the linear elastic stage, followed by asmall number of microcracks in the specimens. In the DEM-AEmodel, only a small number of AE events were monitoredas well. Most AE events developed after the peak andcumulative failure events increased exponentially at thepostpeak stage. In particular, as for specimens with lowerconfining pressure (๐3 = 0.5 and 2.0MPa), the increase ofcumulative AE events did not stop and start again afterthe peak deviatoric stress, while such a phenomenon wasobserved for the specimens with higher confining pressure(๐3 = 4.0 and 6.0MPa).Additionally, the higher the confiningpressure was, the more the intermittent stops occurredbecause a transitory secondary resistance phenomenon tookplace after the simulated specimens were damaged due to thehigh confining pressure. However, the postpeak curves in thephysical experiment had better brittle-to-ductile transition;therefore, no intermittent stops of AE events occurred.
4.2. Spatial Distribution of AE Events. Based on the micro-scopic parameters after calibration, the failure modes of theargillaceous sandstones under different confining pressurescan be seen in Figure 10. The DEM-AE model showed goodagreement with the failure modes derived from the physical
experiments. With the increase in confining pressure, theresidual resistance of rock specimens increased, leading to agradual increase in cracks (see Figure 11). It is noteworthy thattensile cracks always played a dominant role and were 2โผ2.5times as abundant as shear cracks. The number and magni-tude of AE events were also on the rise under the differentconfining pressures.
The temporal evolution of AE events at the stages of 50%peak deviatoric stress, peak deviatoric stress, and postpeakstage is shown in Figures 12โ15. At the point of 50% peakdeviatoric stress, there were a small number of AE events inthe physical experiments, about 7%โผ10% of the cumulativetotal of AE events, while in the numerical simulations, therewere almost no AE events prior to the 50% peak deviatoricstress.
At the peak deviatoric stress, the AE events in the physicalexperiments and the numerical simulations accounted for20%โผ35% of the cumulative total, while no obvious macro-scopic cracks occurred in the specimens during the loadingprocedure. Until loading to 90% of postpeak strength, thephysical experiments and numerical simulations resulted inrelatively obvious cracks among the specimens with theconfining pressures of 0.5, 2.0, and 4.0MPa, accounting for40%โผ55% of the cumulative total of AE events. It is worth
Mathematical Problems in Engineering 13
Number of AE eventsFitting curve of frequency
0
100
200
300
400
500N
umbe
r of A
E ev
ents
โ7.0 โ6.5 โ6.0 โ5.5 โ5.0 โ4.5 โ4.0
Magnitude of AE events
(a)
0
100
200
300
400
500
Num
ber o
f AE
even
ts
โ7.5 โ6.5 โ6.0 โ5.5 โ5.0 โ4.5 โ4.0โ7.0
Magnitude of AE events
Number of AE eventsFitting curve of frequency
(b)
0
100
200
300
400
500
600
700
Num
ber o
f AE
even
ts
โ7.5 โ6.5 โ6.0 โ5.5 โ5.0 โ4.5 โ4.0โ7.0
Magnitude of AE events
Number of AE eventsFitting curve of frequency
(c)
0
200
400
600
800
1000
1200N
umbe
r of A
E ev
ents
โ7.5 โ6.5 โ6.0 โ5.5 โ5.0 โ4.5 โ4.0โ7.0
Magnitude of AE events
Number of AE eventsFitting curve of frequency
(d)
Figure 16: Statistical number of AE events at different gradients under different confining pressures: (a) 0.5MPa; (b) 2.0MPa; (c) 4.0MPa;(d) 6.0MPa.
noting that there were obvious macroscopic cracks in speci-menswith the confining pressure of 6.0MPaonly until 80%ofpostpeak strength.
4.3. Magnitude of AE Events. During monitoring of thespatial distribution of AE events, the magnitude of AE eventscan be calculated in the DEM-AEmodel as well. As shown inFigure 16, when themagnitude of AE events was smaller thanโ6.0 or larger than โ4.5, there was not much differencein the number of AE events under four different confiningpressures. Most of the AE events took place in the rangeโ6.0โผโ4.5 andwere on the increase alongwith the increase inthe confining pressure. Based on the magnitude of AE eventsin Figure 16, it can be seen that AE events conformed to a
normal distribution, and the peaks were within โ5.25โผโ5.0(as shown in Figures 16(a)โ16(d)). Additionally, with theincrease in confining pressure, the concentration area ofpeaks tended to shift to the larger position.
Figure 17 shows the relationship between the AE eventsand the number ofmicrocracks.When the confining pressurewas 0.5MPa, the number of AE events containing only onemicrocrack accounted for over 90% of the total number,which decreased gradually along with the increase of confin-ing pressure, but the total number remained over 85%. As fordifferent confining pressures, the number of microcracksshowed an exponential decrease alongwith the increase ofAEevents. Under the confining pressure of 0.5MPa, a maximumof eight microcracks were generated by only one AE event.When the confining pressure reached 6.0MPa, themaximum
14 Mathematical Problems in Engineering
Number of AE eventsFitting curve of frequency95% confidence interval
0
200
400
600
800
1000
1200
Num
ber o
f AE
even
ts
1 2 3 4 5 6 7 8 90
R2 = 0.997
y = 32200eโx/0.29 + 6.24
Crack number per AE event
(a)
Number of AE eventsFitting curve of frequency95% confidence interval
0
200
400
600
800
1000
1200
Num
ber o
f AE
even
ts
1 2 3 4 5 6 7 8 9 100Crack number per AE event
y = 24064eโx/0.31 + 3.16
R2 = 0.999
(b)
Number of AE eventsFitting curve of frequency95% confidence interval
1 2 3 4 5 6 7 8 9 10 11 12 130Crack number per AE event
0
300
600
900
1200
1500
1800
Num
ber o
f AE
even
ts
y = 32927eโx/0.33 + 5.69
R2 = 0.999
(c)
Number of AE eventsFitting curve of frequency95% confidence interval
0
500
1000
1500
2000
2500
3000N
umbe
r of A
E ev
ents
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 160Crack number per AE event
y = 48534eโx/0.35 + 10.51
R2 = 0.993
(d)
Figure 17: The relationship between the number of AE events and the number of microcracks. (a) 0.5MPa; (b) 2.0MPa; (c) 4.0MPa; (d)6.0MPa.
number of microcracks generated by one AE event increasedto 15, which occurred only once.
4.4. Discussion. As described in Section 4.1, under the dif-ferent confining pressures, the postpeak stage in the physicalexperiments showed better brittle-to-ductile transition; how-ever, this phenomenon was not observed in the numericalsimulations (see Figure 8). As the numerical simulation wasloaded to peak deviatoric stress, massive cracks were coa-lescing and interlocking among most of the particles in thesimulated specimens, leading to an abrupt drop in peakdeviatoric stress. This progression was also demonstrated in
the AE model so that more than 70%โผ80% of the AE eventswere observed only after the peak deviatoric stress. In thephysical experiments, however, hard minerals that exist inargillaceous sandstones were able to resist slippage and insta-bility at the postpeak stage; therefore, the postpeak stageshowed better brittle-to-ductile transition.
In addition, because of the closing of initial cracks or holesin the physical experiments, theAE events of specimens couldbe monitored even at the initial loading stage, which wasnot observed in the numerical simulations. Nevertheless, AEevents at the initial loading stage accounted for only a smallproportion of the entire loading process.
Mathematical Problems in Engineering 15
5. Conclusions
In this paper, a DEM-AE model was presented based on themovement of particles during the loading process. The fun-damental principle of the process was the calculation of thescalar moment of the moment tensor and the determinationof the magnitude of AE events. An algorithm for identifyingthe spatiotemporal location of the sameAE event was put for-ward. With this method, it was possible to analyze and quan-tify the spatiotemporal location and the magnitude duringthe process of crack initiation, propagation, and coalescence.This model was applied to the compression test with differentconfining pressures of argillaceous sandstones. A systematiccontrastive analysis was conducted with the results fromthe physical experiment and the numerical simulation, lead-ing to a good agreement between both cases in terms ofspatiotemporal distribution as well as the magnitude of AEevents. Furthermore, this model was used to analyze themagnitude of AE events and discuss the relationship betweenAE events and microcracks.
With this model, an authentic simulation of AE events inphysical experiments can be reproduced using numericalsimulations. In the near future, this model will be applied tothe production process at the field scale. The performance ofthis model makes it possible to evaluate and prevent seismichazards caused by roadway excavation and coal mining.
Conflicts of Interest
The authors declare that they have no conflicts of interest.
Acknowledgments
Financial support for this work is provided by the NationalNatural Science Foundation of China (no. 51474208), theNational Key Research and Development Program of China(2016YFC0600904), and a project funded by the PriorityAca-demic Program Development of Jiangsu Higher EducationInstitutions (PAPD).Thefinancial support provided byChinaScholarship Council (CSC, Grant no. 201606420013) is alsogratefully acknowledged.
References
[1] Z. Fang and J. P. Harrison, โApplication of a local degradationmodel to the analysis of brittle fracture of laboratory scale rockspecimens under triaxial conditions,โ International Journal ofRockMechanics andMining Sciences, vol. 39, no. 4, pp. 459โ476,2002.
[2] J. Sun and Z. Zhao, โEffects of anisotropic permeability offractured rock masses on underground oil storage caverns,โTunnelling andUnderground Space Technology, vol. 25, no. 5, pp.629โ637, 2010.
[3] D. Becker, B. Cailleau, T. Dahm, S. Shapiro, and D. Kaiser,โStress triggering and stress memory observed from acousticemission records in a salt mine,โ Geophysical Journal Interna-tional, vol. 182, no. 2, pp. 933โ948, 2010.
[4] M. C. He, J. L. Miao, and J. L. Feng, โRock burst process oflimestone and its acoustic emission characteristics under true-triaxial unloading conditions,โ International Journal of RockMechanics andMining Sciences, vol. 47, no. 2, pp. 286โ298, 2010.
[5] C.-P. Lu and L.-M. Dou, โThe relationship between verticalstress gradient, seismic, and electromagnetic emission signalsat Sanhejian coal mine, China,โ International Journal of RockMechanics and Mining Sciences, vol. 70, pp. 90โ100, 2014.
[6] M. F. Cai and X. P. Lai, โMonitoring and analysis of nonlineardynamic damage of transport roadway supported by compositehard rockmaterials in linglong goldmine,โ Journal of Universityof Science and Technology Beijing, vol. 10, no. 2, pp. 10โ15, 2003.
[7] D. G. Aggelis, โClassification of cracking mode in concrete byacoustic emission parameters,โ Mechanics Research Communi-cations, vol. 38, no. 3, pp. 153โ157, 2011.
[8] J. Fortin, S. Stanchits, G. Dresen, and Y. Gueฬguen, โAcousticemission and velocities associated with the formation of com-paction bands in sandstone,โ Journal of Geophysical Research:Solid Earth, vol. 111, no. 10, 2006.
[9] X. Lei, K. Masuda, O. Nishizawa et al., โDetailed analysis ofacoustic emission activity during catastrophic fracture of faultsin rock,โ Journal of Structural Geology, vol. 26, no. 2, pp. 247โ258, 2004.
[10] Z. Li, L.Dou,W.Cai et al., โInvestigation and analysis of the rockburst mechanism induced within fault-pillars,โ InternationalJournal of Rock Mechanics andMining Sciences, vol. 70, pp. 192โ200, 2014.
[11] F. Xiao, G. Liu, Z. Zhang, Z. Shen, F. Zhang, and Y. Wang,โAcoustic emission characteristics and stress release rate of coalsamples in different dynamic destruction time,โ InternationalJournal of Mining Science and Technology, vol. 26, no. 6, pp. 981โ988, 2016.
[12] S.-H. Chang, C.-I. Lee, and Y.-K. Lee, โAn experimental damagemodel and its application to the evaluation of the excavationdamage zone,โ Rock Mechanics and Rock Engineering, vol. 40,no. 3, pp. 245โ285, 2007.
[13] D. Ma, H. Bai, and Y. Wang, โMechanical behavior of a coalseam penetrated by a karst collapse pillar: mining-inducedgroundwater inrush risk,โ Natural Hazards, vol. 75, no. 3, pp.2137โ2151, 2015.
[14] M. Sharafisafa, Z. Aliabadian, R. Alizadeh, and A. Mortazavi,โDistinct element modelling of fracture plan control in contin-uum and jointed rock mass in presplitting method of surfacemining,โ International Journal of Mining Science and Technol-ogy, vol. 24, no. 6, pp. 871โ881, 2014.
[15] K.-B. Min and L. Jing, โNumerical determination of the equiva-lent elastic compliance tensor for fractured rock masses usingthe distinct element method,โ International Journal of RockMechanics andMining Sciences, vol. 40, no. 6, pp. 795โ816, 2003.
[16] M. Cai, P. K. Kaiser, H. Morioka et al., โFLAC/PFC couplednumerical simulation of AE in large-scale underground exca-vations,โ International Journal of Rock Mechanics and MiningSciences, vol. 44, no. 4, pp. 550โ564, 2007.
[17] A. Lisjak, Q. Liu, Q. Zhao, O. K. Mahabadi, and G. Grasselli,โNumerical simulation of acoustic emission in brittle rocks bytwo-dimensional finite-discrete element analysis,โ GeophysicalJournal International, vol. 195, no. 1, pp. 423โ443, 2013.
[18] T. Heinze, B. Galvan, and S. A. Miller, โA new method toestimate location and slip of simulated rock failure events,โTectonophysics, vol. 651, pp. 35โ43, 2015.
[19] C. A. Tang, H. Liu, P. K. K. Lee, Y. Tsui, and L. G. Tham,โNumerical studies of the influence of microstructure on rock
16 Mathematical Problems in Engineering
failure in uniaxial compression-Part I: effect of heterogeneity,โInternational Journal of Rock Mechanics and Mining Sciences,vol. 37, no. 4, pp. 555โ569, 2000.
[20] C. A. Tang, L. G. Tham, P. K. K. Lee, Y. Tsui, and H. Liu,โNumerical studies of the influence of microstructure on rockfailure in uniaxial compressionโPart II: constraint, slendernessand size effect,โ International Journal of Rock Mechanics andMining Sciences, vol. 37, no. 4, pp. 571โ583, 2000.
[21] V. Vajdova and T.-F. Wong, โIncremental propagation of dis-crete compaction bands: acoustic emission andmicrostructuralobservations on circumferentially notched samples of Ben-theim,โ Geophysical Research Letters, vol. 30, no. 14, 2003.
[22] B. Chouet, P. Dawson, T. Ohminato et al., โSource mechanismsof explosions at Stromboli Volcano, Italy, determined frommoment-tensor inversions of very-long-period data,โ Journal ofGeophysical Research-Solid Earth, vol. 108, no. 1, pp. ESE 7-1โESE7-25, 2003.
[23] N. Cho, C.D.Martin, andD.C. Sego, โA clumped particlemodelfor rock,โ International Journal of Rock Mechanics and MiningSciences, vol. 44, no. 7, pp. 997โ1010, 2007.
[24] D. O. Potyondy and P. A. Cundall, โA bonded-particle modelfor rock,โ International Journal of Rock Mechanics and MiningSciences, vol. 41, no. 8, pp. 1329โ1364, 2004.
[25] M. J. Jiang, H. B. Yan, H. H. Zhu, and S. Utili, โModeling shearbehavior and strain localization in cemented sands by two-dimensional distinct element method analyses,โ Computers andGeotechnics, vol. 38, no. 1, pp. 14โ29, 2011.
[26] Z. Chong, X. Li, Q. Yao, J. Zhang, and T. Chen, โAnchoragebehaviour of reinforced specimens containing a single fissureunder uniaxial loading: a particle mechanics approach,โ Ara-bian Journal of Geosciences, vol. 9, no. 12, article no. 592, 2016.
[27] S.-Q. Yang, Y.-H. Huang, H.-W. Jing, and X.-R. Liu, โDiscreteelement modeling on fracture coalescence behavior of redsandstone containing two unparallel fissures under uniaxialcompression,โ Engineering Geology, vol. 178, pp. 28โ48, 2014.
[28] W. Chen and H. Konietzky, โSimulation of heterogeneity, creep,damage and lifetime for loaded brittle rocks,โ Tectonophysics,vol. 633, no. 1, pp. 164โ175, 2014.
[29] S. I. Mayr, S. Stanchits, C. Langenbruch, G. Dresen, and S. A.Shapiro, โAcoustic emission induced by pore-pressure changesin sandstone samples,โ Geophysics, vol. 76, no. 3, pp. MA21โMA32, 2011.
[30] S. Stanchits, S. Mayr, S. Shapiro, and G. Dresen, โFracturing ofporous rock induced by fluid injection,โTectonophysics, vol. 503,no. 1-2, pp. 129โ145, 2011.
[31] S. Baisch, R. Voฬroฬs, E. Rothert, H. Stang, R. Jung, and R.Schellschmidt, โA numerical model for fluid injection inducedseismicity at Soultz-sous-Foreฬts,โ International Journal of RockMechanics andMining Sciences, vol. 47, no. 3, pp. 405โ413, 2010.
[32] K. Mogi, โEarthquakes and fractures,โ Tectonophysics, vol. 5, no.1, pp. 35โ55, 1967.
[33] R. Madariaga, โDynamics of an expanding circular fault,โBulletin of the Seismological Society of America, vol. 66, no. 3,pp. 639โ666, 1976.
[34] K. Kovari, A. Tisa, H. H. Einstein, and J. A. Franklin, โSuggestedmethods for determining the strength of rock materials intriaxial compression: revised version,โ International Journal ofRockMechanics andMining Sciences, vol. 20, no. 6, pp. 283โ290,1983.
[35] Itasca Consulting Group, PFC2D Manual, Version 5.0, ItascaConsulting Group, Minneapolis, Minn, USA, 2014.
Submit your manuscripts athttps://www.hindawi.com
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
MathematicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Mathematical Problems in Engineering
Hindawi Publishing Corporationhttp://www.hindawi.com
Differential EquationsInternational Journal of
Volume 2014
Applied MathematicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Probability and StatisticsHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Mathematical PhysicsAdvances in
Complex AnalysisJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
OptimizationJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
CombinatoricsHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Operations ResearchAdvances in
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Function Spaces
Abstract and Applied AnalysisHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of Mathematics and Mathematical Sciences
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
The Scientific World JournalHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Algebra
Discrete Dynamics in Nature and Society
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Decision SciencesAdvances in
Discrete MathematicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com
Volume 2014 Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Stochastic AnalysisInternational Journal of
Recommended