View
612
Download
1
Category
Tags:
Preview:
DESCRIPTION
General Information the regulation of the engineering profession in Kenya
Citation preview
Page 1 of 20
Regulation and Registration of Engineering Profession and the Problem with
the Engineers Board of Kenya (EBK) Introduction
Kenya is destined to be a medium economy state by the year 2030 as stipulated in vision 2030. This is
through industrialization amongst other strategies stipulated in vision 2030. In order for
industrialization to be realized, a number of strategies must be put in place among them being to train
adequate number of engineers and corresponding Engineering Technologists, Technicians and Craft
persons/Artisans in defined proportions and to offer sustainable incentives that can sustain them not to
migrate to other professions and/or other countries. The current challenges amongst others include lack
of interest in the engineering profession due to; poor remuneration, poor professional body treatment,
gender balance, lack of proper training due to poor facilities in most academic institutions and poor
policy implementation in various relevant government departments.
In order for Kenya to make realistic breakthrough in industrialisation and technological development
it must begin by ensuring that it has a critical mass of well trained and qualified Scientists, Engineers,
Engineering Technologists, Engineering Technicians and craft persons/artisans who comprise the
Engineering Team with each team members roles clearly defined. Kenya critically requires four cadres of staff namely an engineer, an engineering technologist, an engineering technician and a craft
person/ artisan (the fifth cadre the engineering scientist belongs to either engineer or engineering technologist who has attained a PhD degree). For most developed countries the ideal ratio for the four
categories of professional is 1:2:4:16, while a typical developing country like Kenya, the more realistic
ratios would be 1:3:12:60.
The engineering profession in Kenya is regulated by the Engineers Board of Kenya (EBK) under the
Engineers Act, 2011. The Board is responsible for the registration of Engineers and consulting firms,
regulation of engineering professional services, accrediting engineering courses in the institutions of
higher learning, setting of standards, development and general practice of engineering. The act
prescribes very deterrent penalties for offering employment to persons who are not registered by them.
The functions and powers of the board do not mention anything about engineering technologists,
engineering technicians and the craft persons/artisans who form the largest part of the engineering
team and who do more than 98% of the engineering activities in Kenya.
This paper looks at the various challenges facing engineering profession and gives suggested strategies
and solutions to the challenges that can enable Kenya to attain vision 2030 and also to sustain her
Engineering professionals, train and sustain more Engineers, Engineering Technologists, Engineering
Technicians and Craft persons/Artisans with International recognition. The paper further analyses
some of the problems with the current EBK Act of 2011.
Institution of Engineering Technologists and Technicians Profile
1. The Institution of Engineering Technologists and Technicians (IET) was registered by the Registrar of Societies at the Attorney Generals chambers on 16th November 2011 under the certificate of registration number 35998; the Institution to date has over three hundred members
(300).
2. In January 2012, the authors (who were then the Interim officials) made media announcements calling on potential members to register with the interim office housed at Technical University
Page 2 of 20
of Kenya (TU-K). TU-K was seen to be a more central point and also the major trainer of these
levels of cadres.
3. The First Annual General Meeting for the Institution of Engineering Technologists and Technicians was held on 2
nd Feb. 2013 at the Technical University of Kenya
4. The proposed Kenya Engineering Technologists, Technicians and Craft persons Proposed Bill was published on 31
st August 2013[Kenya Gazette Supplement No. 103 (Bills No.45)]. By the
time the tenth parliament was winding up its business, the bill had gone through the first
reading in Parliament. It is now awaiting the eleventh parliament for approval since it is already
a house document. Hon. Dr.Julius Kones, Member for Konoin Constituency had moved the bill
through Private members motion. Since Hon. Dr. Kones did not manage to secure a seat in
parliament after the 2013 General Elcetion we have not be able to get any MP to continue with
Hon. Dr. Kones motion so that this bill can be enacted by Parliament. We are urgently looking for assistance from any MP who can present the bill for the second and third reading. The bill is
available in the internet via http://www.kenyalaw.org/klr/index.php?id=98, KNA.No.45.
5. A stakeholders meeting of the Institution of Engineering Technologists and Technicians was held on 10
th September 2013 at the Technical University of Kenya; the meeting was sponsored
by the National Council of Science and Technology (NCST) and the Technical University of
Kenya.
6. The second Annual General Meeting for the Institution of Engineering Technologists and Technicians was held on 22
nd Feb. 2014 at the Technical University of Kenya.
7. Attempts are on the way for the Institution to be recognized by the following international educational accords for international membership recognition:
a) WASHINGTON ACCORD 1989 The accord recognizes the equivalence of accredited engineering education programs leading to the engineering degree programs.
b) SYDNEY ACCORD The accord recognizes the equivalence of accredited engineering technology education programs leading to the engineering technology degree programs.
c) DUBLIN ACCORD- Which recognizes the equivalence of educational base for engineering technicians.
Why is Regulation and Registration of Engineering Profession necessary?
Regulation and Registration of any Profession that touch on the Safety and Health and welfare of the
public is extremely necessary worldwide. The most notable ones are the Engineering and Medical
Professions. The Engineering Team mentioned above has five cadres, but only one is being registered
in Kenya by EBK; the Medical team also has five cadres Medical scientists, Doctors/Dentists, Medical Clinical Officers, Medical Nurses and Lab. Technologists. Unlike the Engineering Team all
the cadres in the Medical Team are regulated by ACTS of Parliament and all the personnel are
registered and therefore accountable for their actions.
The Attributes and/or Roles of Engineers, Engineering Technologists and Engineering
Technicians
a) Attributes of an Engineer Engineers apply their lifelong learning, critical perception and engineering judgment to the
performance of engineering services. They challenge current thinking and conceptualize alternative
approaches, often engaging in research and development of new engineering principles, technologies
Page 3 of 20
and materials. Engineers apply their analytical skills and well developed grasp of scientific principles
and engineering theory to design original and novel solutions to complex problems. Their disciplined
and systematic approach to innovation and creativity, comprehension of risks and benefits and
informed professional judgment enables them to select optimal solutions, justify and defend the
selection to colleagues, clients and community.
Registered Professional Engineers can be expected to comprehend complexity, function
independently and display leadership within multi-disciplinary and cross-cultural teams. Within their
engineering discipline, they will optimize costs and benefits to clients and community within identified
constraints, while achieving desired outcomes ethically, and within the context of a safe and
sustainable environment. They accept ultimate responsibility for the selection and application of design
tools, implementation strategies and overall integration and functionality of engineering projects and
programs.
b) Attributes of an Engineering Technologist Engineering Technologists exercise ingenuity, originality and understanding in adapting and applying
technologies, developing related new technologies or applying scientific knowledge within their
specialized technical environment. Their education, expertise and analytical skills equip them with a
robust understanding of the theoretical and practical application of engineering and technical
principles. Within their branch of technology, they contribute to the improvement of standards and
codes of practice, and the adaptation of established technologies to new situations.
Registered Engineering Technologists can be expected to determine interactions between a
technology and the system, in which it operates, recognize and take account of its suitability and
manage associated technical risks. Technologists accept responsibility for the detailed technological
requirements of their engineering services with due regard to the fundamental properties and
limitations of components and systems involved. They may lead and manage teams (e.g. engineering
technicians) engaged in inspection, approval and certification of designs, tests, installations and
reliable operations. They identify problematic circumstances, take remedial action and keep
colleagues, clients and community informed, while ensuring performance-based criteria are satisfied
within a safe and sustainable environment.
The Difference in Education and Training between the Engineer and Technologist Previously there used to be a big difference between a technologist and engineer in terms of their
education when technologist used to hold a 3 year course qualification of Higher National Diploma.
But with the replacement of Higher Diploma with a 4 year course leading to Bachelor of Technology,
the difference between a technologist and engineer in terms of education and training is extremely
minimal and actually they both have same roles in practice.
In general the engineer is supposed to take the scientist research findings theories and principles- then conceptualize them with the aim of coming up with new designs, new materials and systems to
serve society better (this is normally referred to as Industrial Research as opposed to Basic or
Theoretical Research that is carried out by Engineering Scientists). This means that the Engineers work is mainly in the office and in the labs to test the new designs/materials/systems developed then
pass over to Engineering Technology personnel for implementation. In this way the country can be
able to develop.
On the other hand the technologist is supposed to implement and/or put in practice what the engineer
has developed from the scientist research findings. Besides, the technologist has the role of interpreting
and modifying designs, systems and materials developed by the engineer to suit the conditions on the
Page 4 of 20
ground. This means that the Engineering Technologists work is in the field where he/she undertakes
the implementation activities.
The expected difference in education and training between the Engineer and Technologist
Subject Material Expected % for Engineer Expected % for
Technologist
Mathematics If 100% 70 80%
Engineering Sciences If 100% 70 80%
Management courses 70 -80% If 100%
Practical courses e.g.
Computer courses, Lab. and
Workshop Courses, etc.
70 -80% If 100%
Other Courses If 100% 100% i.e. same
The engineer requires more mathematics and engineering sciences to enable him/her conceptualize and
design, while the technologist requires more management and practical courses to enable him/her carry
out the implementation of projects. The percentages given are theoretical as the reality on the ground is
very different as we have never sat down to agree on the actual subject contents; different Universities
develop their curricula without discussing and agreeing on the contents of the respective curricula. In
most cases both curricula are similar in contents. The progression from degree level is to MSc/MEng
and MTech respectively, then to PhD/DSc and PhD/DTech respectively (see figure for pathways
attached).
c) Attributes of an Engineering Technician Engineering Technicians apply their detailed knowledge of standards and codes of practice to
selecting, specifying, and installing, commissioning, monitoring, maintaining, repairing and modifying
complex assets, such as structures, plant, equipment, components and systems. Their education,
training and experience equip them with the necessary theoretical knowledge and analytical skills for
testing, fault diagnosis and understanding the limitations of complex assets in familiar and well defined
operating situations.
Registered Engineering Technician can be expected to exercise engineering judgment within the
scope of accepted standards and codes of practice to the design, inspection, certification, safe operation
and cost-effectiveness of complex assets. They may supervise tradespeople/crafts persons, lead and
manage teams and utilize advanced software and design aids to achieve practical and reliable designs,
installations and operations of complex assets.
Why is it that EBK does not want to register other engineering cadres as in other countries?
Having understood the roles of each cadre in the three cadres of the engineering team we can now
explain why the EBK officials do not want to recognize the three cadres that belong to the Engineering
Technology.
Immediately the British who were managing the Engineers Registration (ERB) left in the 1970s,
Kenyan engineers all graduates of University of Nairobi took over. The Kenyan officials realized that
ERB was a gold mine and started limiting the number of membership. They also realized that most
industries were run by the three cadres in Engineering Technology. Further they realized that the
engineering activities in the Kenyan industries were those that belonged to implementation and
therefore required only the engineering technology personnel; there was no industrial research being
conducted in the local industries. Most industries in Kenya were multinational corporations who
Page 5 of 20
conducted their research abroad and therefore denying the local engineers industrial research work.
(This is still the scenario presently).
Our Engineers then turned the ERB/EBK into a private club unofficially and denied the other three
cadres to register for fear of them becoming irrelevant since all engineering work will be done by
three cadres. Even now almost all engineering work in Kenya is being performed by the three cadres
and the engineers get credit; drawing and designs are also prepared by these three cadres and the
engineers only come sign for them since the three cadres are not licensed to carry out any engineering
work in the country. This is purely a case of exploitation and therefore professional corruption.
Once the act to regulate Engineering technology and start registering Engineering Technologists,
Engineering Technicians and Engineering Crafts persons like in other countries, the engineers will
have very little work and therefore will not be getting free money as it is the case presently. Eventually
they will be forced to do what they are supposed to do i.e. coming up with new designs, new materials,
new systems (which all belong to industrial research). That is when Kenya will start developing or
industrializing. But for the time being the engineers are engaged in activities that are mainly meant for
the engineering technology personnel.
Engineering Board of Kenya (EBK)
The Engineers Board of Kenya (EBK) is a statutory body established under The Engineers Act, 2011
(No. 43). Its role is the registration of Engineers and Firms, regulation of engineering professional
services, setting of standards, development and general practice of Engineering. EBK is supposed to
contribute to the transformation of the Engineering service which will be expected to function
effectively and innovatively in a results- oriented and accountable manner.
The Kenya Engineers Registration Board (ERB) was a statutory body established through an Act of
Parliament in 1969. A minor revision was done in 1992, to accommodate Technician Engineer grade.
However, in 2011 a major revision was done to remove Technician Engineer grade giving rise to
The Engineers Board of Kenya (EBK) with a new face and strength to further its duties. The Board
has been given the responsibility of regulating the activities and conduct of Practicing Engineers in the
Republic of Kenya in accordance with the functions and powers conferred upon it by the Act. Under
Part VI of the Engineers Act (according to articles 48(1) and 49), a person shall not engage in the
practice of engineering unless that person has been issued with a license and has complied with the
requirements of the Act. Registration with the Board is thus a license to practice engineering in Kenya.
Object and purpose of the Board
The Board is responsible for the registration of engineers and firms, regulation of engineering professional
services, setting of standards, development, and general practice of engineering.
The following articles need to be examined carefully as they affect the industrial development of this
country:
Article 16. Subject to the provisions of this Act, a person shall be eligible for registration under this
Act as a professional or consulting engineer if (a) For a professional engineer, that person
(i) is registered as a graduate engineer and has obtained practical experience as prescribed under this Act;
(ii) has passed professional assessment examination conducted by the Board; and
Page 6 of 20
(iii) is a corporate member of the Institution of Engineers of Kenya; (This article contravenes Chapter 4 of the Bill of Rights article 36 (2) of the Constitution of Kenya)
(b) For a consulting engineer, that person (i) has practiced in a specialized engineering field as a professional engineer for a period
determined by the Board; and
(ii) has achieved a standard of competence to enable him to practise as a consulting engineer in that particular specialization.
Qualifications for registration as graduate engineer Article 18. Subject to provisions of this Act, a person shall be eligible for registration under this Act as
a graduate engineer if that person (a) Is a holder of a degree, diploma or its equivalent from a university, college or school of
engineering or any other institution recognized by the Board; and
NB: Although a diploma is also a requirement for registration, the EBK officials do not accept
Diplomas from Kenya for the purpose of registration. Worse still the officials do not accept
Masters and PhD degrees for registration; they only consider a first degree, BSc for registration. In all other countries worldwide any postgraduate degree automatically qualifies for registration
since to qualify for any postgraduate degree one has to do a research project that is properly
supervised by doctorates.
(b) Is a citizen or a permanent resident of Kenya
Article 45. A person who, being in charge of a training institution which is not recognized by the
Board as an institution registered or seeking registration under this Act (a) admits to the institution under his charge any person for purposes of training in the engineering
profession;
(b) purports to be conducting a course of training or examining persons seeking registration under this Act; or
(c) issues any document, statement, certificate or seal implying that (i) the holder thereof has undergone a course of instruction or has passed an examination
recognized by the Board; and
(ii) the institution under his charge is recognized by the Board as an institution for training of person seeking registration, commits an offence and is liable on conviction
to a fine of five million shillings or to imprisonment for a term not exceeding five
years, or both.
Prohibition for the use of the term engineer by unregistered or unlicensed persons 1. Article 46. (1) The terms engineer and engineers are protected under this Act and shall
only be applied to persons or bodies fulfilling the requirements of this Act. (This article
contravenes Chapter 4 of the Bill of Rights article 24 (1) of the Constitution of Kenya) (2) A person who, being not registered or licensed under this Act (a) willfully and falsely takes or uses in any way the style or form or title of engineer or
engineers in describing his occupation or his business or any other name, style, title, addition or description implying whether in itself or in the circumstances in which it is used, that such
person or body or persons is an engineer or engineers; or (b) Displays any sign, board, card or other device or uses a prescribed stamp representing or
implying that he is an engineer, commits an offence.
(3) The Board may grant exemptions upon application to any person or group of persons for the use of
the description or use of the term engineer or engineers and such exemptions shall be in accordance with any written International Convention or Treaty ratified by Kenya.
Page 7 of 20
Prohibition on provision of professional engineering services by body of persons Article 47. (1) A body of persons shall not carry on the business of engineering unless one of its
partners or directors, as the case may be, is a professional engineer.
(2) Where a partner or director of a body of persons mentioned under subsection (1), dies, that body of
persons may, despite the provision of subsection (1), continue to carry on the business of engineering
until such time as the administration of the estate of the deceased is completed as if the legal
representatives were professional engineers.
(3) Any person who contravenes the provisions of this section commits an offence.
Prohibition of employment of unregistered persons Article 48. (1) A person shall not employ or continue to employ any person to offer professional
engineering services or works if that person is not registered under this Act.
(2) A person shall not take up or continue in any employment as a professional engineer or consulting
engineer unless that person is registered as a professional engineer or consulting engineer. (Where
does the line divide professional engineering service or works, and other engineering services or
works?) (3) An employer shall not employ or engage a graduate engineer in any work or professional
engineering services or works unless that graduate engineer is under the supervision of a professional
or consulting engineer. (Where does the line divide professional engineering service or works, and
other engineering services or works?)
(4) A person who contravenes any provision of this section commits an offence.
General penalty: Article 55. A person who commits an offence under this Act for which no specific penalty is provided
for is liable to a fine of two hundred thousand shillings or to imprisonment for a term not exceeding
one year, or both.
Under Part VI of the Engineers Act (according to articles 48(1) and 49), a person shall not engage in
the practice of engineering unless that person has been issued with a license and has complied with the
requirements of the Act. Registration with the Board is thus a license to practice engineering in Kenya.
Engineering and Engineering Technology
In broad the Engineering Profession is divided into Engineering and Engineering Technology. The
Engineering team consists of five (5) cadres Engineering Scientists, Engineers, Engineering Technologists, Engineering Technicians and engineering Crafts persons. The Engineering Scientists
are usually PhD holders, and belong to either Engineers or Engineering Technologists. That leaves
only four cadres (i.e. Engineers, Engineering Technologists, Engineering Technicians and engineering
Crafts persons) who require registration.
Page 8 of 20
(1 -2 years Course) (2 years Diploma) (4 years degree) (4-5years degree)
What is the implication of Part VI of the EBK ACT, and the removal of Technician Engineer
Grade from the ACT?
The removal of the Technician Engineer grade meant that EBK has no role on the regulation of
Engineering Technology in Kenya. The three cadres of the Engineering team i.e. Engineering
Technologist, Engineering Technician and Engineering Craftsperson are not catered for in the EBK
Act and, therefore, are NOT are allowed to engage in any engineering activities in Kenya as they
cannot be licensed by EBK as per the requirement of Part VI of the ACT.
The Difference between Engineering and Engineering Technology
Engineering Engineering is a profession in which knowledge of advanced mathematical
and natural sciences gained by higher education, experience, and practice is
devoted to the creation of new technology for the benefit of humanity.
Engineering education for the professional focuses primarily on the
conceptual and theoretical aspects of science and engineering aimed
at preparing graduates for the practice of engineering closest to the
research, development, and conceptual design functions.
Engineering
Technology
Engineering technology is the profession in which a knowledge of the
applied mathematical and natural science gained by higher education,
experience, and practice is devoted to application of engineering principles
and the implementation of technological advances for the benefit of
humanity. Engineering technology education for the professional focuses
primarily on analyzing, applying, implementing, and improving existing
technologies and is aimed at preparing graduates for the practice of
engineering closest to the product improvement, manufacturing, and
engineering operational functions.
In USA the Engineering Technology Commission (ETC) views engineering technology as
an integral part of the engineering enterprise and holds that baccalaureate (degree) engineering
technologists appropriately function as professional practitioners, rather than supporting Para-
Page 9 of 20
professionals, in this enterprise. It is further held that an appropriate accreditation activity is necessary
to support the uniqueness of this component. The Technology Accreditation Commission (TAC) of the
Accreditation Board for Engineering and Technology (ABET) serves this function.
The ETC believes that professional registration is important, especially as it relates to those activities
that directly affect the health, safety, and welfare of the public. Further, it supports the
continuance of the industrial exemption, while recognizing the importance of registration in industry
for some disciplines. The ETC further supports and encourages registration for all eligible
engineering technology faculties, since they typically are engineering practitioners.
The Engineering Team In today's modern high-tech industry, many of the complex technical problems, including the
development of new products, require a team effort. Individuals on the team may include scientists,
engineers, engineering technologists, engineering technicians, and Vocational Technicians or
Craftsperson*. Each of these individuals contributes different knowledge and skills gained from their
educational preparation and experience. Most people are familiar with the term scientist and associate
it with individuals with advanced degrees and research or theoretical interests. Similarly the term
craftsperson is normally recognized and associated with an individual with a highly specialized skill.
However, the distinction between engineer, engineering technologist, and engineering technician may
not be as clear. An engineer is typically a graduate from a four-year engineering degree program,
whereas the technologists or technician is typically a graduate of a four-year or a two-year degree
program in engineering technology respectively from Universities or Technical Institutes/Polytechnics.
Scientists are the most theoretical of the team members. They typically seek ways to apply new
discoveries to advance technology for mankind. Most engineering scientists have an earned doctorate
in engineering or a closely related discipline.
*In most developed and newly industrialized countries the cadre of Craftsperson is being phased out
and therefore there is no registration for it; the existing craftsperson are encouraged to upgrade
themselves to the grade of engineering technician by acquiring a diploma.
International Agreements Governing Mutual Recognition of Engineering
There are six international agreements governing mutual recognition of engineering qualifications and
professional competence. In each of these agreements countries/economies who wish to participate
may apply for membership, and if accepted become members or signatories to the agreement.
1) Agreements covering tertiary qualifications in engineering There are three agreements covering mutual recognition in respect of tertiary-level qualifications in
engineering:
a) Washington Accord: This accord was signed in 1989; it recognizes substantial equivalence in the accreditation of qualifications in professional engineering education leading to the
Engineering Degree, normally of four to five years duration
b) Sydney Accord: Flowing from the Washington Accord, a similar Agreement was developed for Engineering Technologists or Incorporated Engineers, called the Sydney Accord (SA),
which was signed in June 2001. It recognizes substantial equivalence in the accreditation of
qualifications in engineering technology, normally of three to four years duration.
Page 10 of 20
c) Dublin Accord: The Dublin Accord (DA) is an Agreement for substantial equivalence in the typifying tertiary qualifications for technician engineering education, normally of two years duration. It commenced in 2002.
Note: There is no Accord for the Crafts persons cadre as this cadre is being phased out and replaced by the Engineering Technician cadre. Besides, the skills required by the crafts person are unique to a
particular country/economy and is not universal.
Note: The EBK officials would not like the EBK to be members of the three international accords as
they fear those Kenyans they deny registration will apply for registration in other member countries
and then EBK will be forced to register them.
2) Agreements covering competence standards for practicing engineers
The other three agreements cover recognition of equivalence at the practising engineer level i.e. it is
individual people, not qualifications that are seen to meet the benchmark standard. The concept of
these agreements is that a person recognized in one country as reaching the agreed international
standard of competence should only be minimally assessed (primarily for local knowledge) prior to
obtaining registration in another country that is party to the agreement.
a) APEC Engineer agreement: The oldest such agreement is the APEC Engineer agreement which commenced in 1999. This has Government support in the participating APEC
economies. The representative organization in each economy creates a "register" of those
engineers wishing to be recognized as meeting the generic international standard. Other
economies should give credit when such an engineer seeks to have his or her competence
recognized. The Agreement is largely administered between engineering bodies.
(APEC - Asia-Pacific Economic Cooperation)
b) International Professional Engineers agreement: The International Professional Engineers agreement commenced in 2001: It operates the same competence standard as the APEC
Engineer agreement but any country/economy may join. The parties to the agreement are
largely engineering bodies. There are intentions to draw IPEA and APEC closer together.
c) International Engineering Technologist agreement: The International Engineering Technologist agreement was signed by participating economies/countries in 2003. The parties
to the Agreement have agreed to commence establishing a mutual recognition scheme for
engineering technologists.
The Registration of Engineering and Technology Cadres in other Countries As mentioned above most countries, and more especially the industrialized and newly industrialized
countries have enacted laws that govern the Engineering profession (i.e. bothe engineering and
engineering technology). Some of the countries are as follows:
1. United Kingdom: Engineering Council The engineering profession in the United Kingdom is regulated by the Engineering Council through
engineering institutions that are licensed to put suitably qualified persons on the Engineering Council's
Register of Engineers. The Register has three sections or cadres:
Chartered Engineer (CEng),
Incorporated Engineer (Engineering Technologist) (IEng), and
Engineering Technician (EngTech).
Page 11 of 20
Applicants for registration are required to satisfy the competence standards set by Engineering Council
and laid down in UK-SPEC (UK Standard for Professional Engineering Competence). Benefits of
Membership and Engineering Council Registration:
It identifies you as having competences that employers value;
It indicates that your competence, and your commitment to professionalism, have been assessed
by other engineering professionals;
It demonstrates that your competence may be compared with standards applicable in other parts
of the world;
It confirms that your commitment to professionalism is underwritten by the support of a
national engineering institution licensed by the Engineering Council.
2. Nigeria: Council for the Regulation of Engineering in Nigeria (COREN) Establishment of the Council for the Regulation of Engineering in Nigeria - There shall be established
on the coming into force of this Act, a body to be known as the Council for the Regulation of
Engineering in Nigeria (hereafter in this Act referred to as the Council) which shall be a body corporate by the name aforesaid and be charged with the general duty of [1992 No. 27]
(a) Determining who are engineers for the purposes of this Act; (b) Determining what standards of knowledge and skill are to be attained by persons seeking to
become registered as engineers and raising those standards from time to time as circumstances
may permit;
(c) securing, in accordance with the provisions of this Act, the establishment and maintenance of a register of persons entitled to practice as registered engineers and the publication from time
to time of lists of those persons;
(d) regulating and controlling the practice of the engineering profession in all its aspects and ramifications;
(e) Performing the other functions conferred on the Council by this Act.
The registers of engineering personnel (in this Act referred to as the registers) shall consist of four registers, one each for:
(a) Registered engineers (Engr);
(b) registered engineering technologists (Engn. Tech);
(c) registered engineering technicians (Tech); and
(d) registered engineering craftsmen (A registered engineering craftsmen shall use his full title with his
trade in bracket under his name).
Registration as Engineers
(1) Subject to section 16 and to rules made under section 4 (4) of this Act, a person shall be entitled to
be fully registered under this Act if (a) he has attended a course of training approved by the Council under the next following section; (b) the course was conducted at an institution so approved, or partly at one such institution and
partly at another or others;
(c) he holds a qualification so approved; and (d) he holds a certificate of experience issued in pursuance of section 9 of this Act; and (e) he has completed a minimum of two years approved post-graduate training and has passed or
is exempted from professional interview;
(f) in the case of a craftsman, he has completed a minimum of two years working experience in his trade and submits an acceptable certificate of experience;
(g) He has completed his second year of industrial pupilage in an approved establishment.
Page 12 of 20
Transfer from one register to the other
1. An engineering craftsman may apply to transfer to the register of engineering technicians if he obtains the Ordinary National Diploma Certificate or an approved equivalent educational
qualification and the required working experience.
2. An engineering technician may apply to transfer to the register of engineering technologists if he obtains the Higher National Diploma Certificate or he has successfully completed an
equivalent course of study in a polytechnic or college of technology or any other approved
institution.
3. An engineering technologist may apply to transfer to the register of engineers if he passes the examination accredited by the Council, the academic content of which shall
meet the requirement for registration as an engineer; or
attends a post-Higher National Diploma course approved by the Council and run by a
polytechnic or university and passes an examination accredited by the Council; or
passes a university degree programme or any examination conducted by any other
body authorized by Council
3. South Africa: Engineering Council of South Africa (ECSA)
Establishment of the Engineering Council of South Africa: There is hereby established a juristic person
to be known as the Engineering Council of South Africa. The Engineering Council of South Africa
(ECSA) is a statutory body established in terms of the Engineering Profession Act, 2000 (Act 46 of
2000), and derives its powers and responsibilities from the Act. The main focus of the Act is the
promotion of public safety, health and interests in relation to actions of persons registered with ECSA.
In Order to Achieve its Main Focus ECSA Performs the Following Functions: Academic Standards Professional Development Standards and Registration Government Liaison International Recognition
Registration: Candidates Application for registration as a candidate engineer will require certified proof that the applicant has
a recognized or accredited academic qualification. If an applicant has a foreign qualification, a
copy of the qualification certificate as well as an academic record reflecting all subjects taken and
passed during the years of study should be submitted with the application. Other benefits of
registering first as a candidate engineer are:
It demonstrates the candidates identification with the ideals of the profession, namely the maintenance of a high level of standards and of professionalism in the interest of the
public and the country as a whole.
As the industry is increasingly in need of registered persons, candidates are therefore in an advantageous position over non-registered practitioners.
Candidate registration is also an indication of the persons aspiration to become registered as a professional in the future.
Employers commitment to candidates regarding their professional development is in many cases more apparent when they are registered.
Persons registered as candidates are normally subjected to a formally structured training program, which will prepare them for professional registration.
Categories of registration
18. (1) After obtaining the required qualification and experience, ECSA registers engineering
practitioners in the following professional registration categories:
Page 13 of 20
The categories in which a person may register in the engineering profession are (a) professional, which is divided into
Professional Engineer (Pr Eng), Professional Engineering Technologist (Pr Tech Eng), Professional Engineering Technician (Pr Techni Eng), and Professional Certificated Engineer (Pr Cert Eng).
In each of these categories, provision is made for candidate registration. The academic and
experience requirements for professional registration are as follows:
Category Academic Qualification Minimum Experience
Professional Engineer BSc(Eng)/ B Eng (4yrs) 3 years
Professional Engineering
Technologist
BTech (Eng) 3 years
Professional Engineering
Technician
National Diploma 3 years
Professional Certificated
Engineer
Government Certificate of
Competency for Engineers, Mine
Managers, Marine, Electrical and
Mechanical Engineers
3 years in responsible
position - 1 year must be as
the engineer appointed in
terms of an applicable Act
(b) candidate, which is divided into (i) Candidate Engineer;
(ii) Candidate Engineering Technologist;
(iii) Candidate Engineering Technician; or
(iv) Candidate Certificated Engineer
(c) Specified categories prescribed by the council.
(2)A person may not practice in any of the categories contemplated in subsection (1), unless he or she
is registered in that category.
(3) A person may practice in a consulting capacity in the category in which he or she is registered.
(4) A person who is registered in the category of candidate must perform work in the engineering
profession only under the supervision and control of a professional of a category as prescribed.
4. Canada: Engineering Technology ACT of 1973
The act registers two categories: Engineering technician and Engineering technologist. Canada has a
separate Act for professional engineers.
5. Australia: Engineers Australia
Engineers Australia administers three National Engineering Registers on advice from a board
established to ensure the registers operate with integrity and in the public interest. Registration on the
National Engineering Registers is available in three occupational categories:
National Professional Engineers Register (NPER),
National Engineering Technologists Register (NETR),and
National Engineering Associates Register (NEAR)
The following titles are used by members of Engineers Australia:
NPER recognized as MIEAust CPEng NETR recognized as TMIEAust CEngT NEAR recognized as OMIEAust CEngO
Page 14 of 20
The National Professional Engineers Register (NPER) and the National Engineering Technologists
Register (NETR) and the National Engineering Associates (Engineering Technician) Register
(NEAR) are administered to safeguard the community at no cost to government.
Engineers Australia administers the national engineering registers with input from the National
Engineering Registration Board to ensure that the registers operate in the public interest.
Admission to the registers is not restricted to members of Engineers Australia or any other professional
association. However, the registers currently are aligned to occupational categories - Professional
Engineers, Engineering Technologists and Engineering Associates. The occupational category a
member belongs to is determined on the basis of his or her original qualification, normally a BEng (4
years), a BTech (3 years) or a TAFE Advanced Diploma / Associate Degree or Engineering Technician
Course (2 years), respectively.
All registered engineering practitioners observe a common Code of Ethics; undertake to accept
responsibility for outcomes only within their area of competence and specifically commit to keeping
up-to-date through continuing professional development to sustain their engagement in delivering
engineering services. They deliver engineering outcomes that minimize adverse social, economic and
environmental consequences, with due regard for the safety, health and welfare of the community.
Public safety is assured when only competent practitioners are registered and provide engineering
services in critical areas. Registered practitioners will be engaged to provide services in such areas
only if stipulated by regulation or demanded by the market.
There are three occupational categories in the engineering workforce - engineers, technologists and
associates. Practitioners in these categories cooperate in various ways to perform engineering services.
Their activities and competencies are often closely inter-related and it is difficult and sometimes
artificial to say where the responsibilities of one occupational category end and those of another begin.
There are activities that could be undertaken in different circumstances by any member of the
engineering team. Other activities are clearly the province of one occupational category but not of
another - for example, the province of a Professional Engineer but not an Engineering Associate, or
vice versa. This distinction will often be determined by the standard to which competency has been
demonstrated against the Australian Engineering Competency Standards Stage 2.
6. New Zealand: Chartered Professional Engineers of New Zealand Act of 2002
IPENZ is the Registration Authority under the Chartered Professional Engineers of New Zealand Act
of 2002. IPENZ also operates registers of current competence for Professional Engineers, Engineering
Technologists and Engineering Technicians. IPENZ operates the national registers of current
competence-based registers for:
a) Professional Engineers, b) Engineering Technologists, and c) Engineering Technicians.
Professional Engineer: Capable of dealing with
complex engineering
problems and activities
Engineering
Technologist:
Capable of dealing
with broadly- defined
engineering problems
and activities
Engineering
Technician: Capable
of dealing with well-
defined engineering
problems and activities
Page 15 of 20
Qualification: New
Zealand qualification
for entry to
occupational group
Four-year Bachelor of
Engineering (Honours)
Three-year Bachelor
of Engineering
Technology
Two-year New Zealand
Diploma in
Engineering
National current-
competence register
International
Professional Engineer
(IntPE)
Engineering
Technology
Practitioner (ETPract)
International
Engineering
Technologist (IntET)
Certified Engineering
Technician (CertETn)
Associated IPENZ
Competence-based
Membership Class
Professional Member
(MIPENZ)
Technical Member
(TIPENZ)
Associate Member
(AIPENZ)
And Others
Reasons for the Enactment of the Engineering Technologists and Technician Bill No., 45 of 2012
1. The ERB/EBK as it is cannot be implemented because of the following reasons: a. ERB/EBK Act implies that the engineer is the only person to do everything concerning
any engineering project in Kenya.
b. The number of registered engineers presently is less than 1800; more than 70% of these engineers are working as civil servants and some parastatals, leaving less than 600 who
are working in private companies and very few as consultants. {Kenyan engineers
registered and working in South Africa are more than 1800; they went to register in
South Africa when they were denied registration by ERB}
c. In Kenya there are more than 700 students pursuing degree course in engineering, and all of them are each supposed to go for industrial attachment at least twice. The
ERB/EBK requires that each of these student should be supervised in industry by a
registered engineer!!!. More than 90% of the industries do not have registered
engineers, meaning that we should not take our students for industrial attachment.
d. The Act does not want any employer to employ a person not registered by ERB/EBK to carry out engineering work. Such a person is reliable for a fine of not less than KES
5,000,000/- or 5 years imprisonment or both. If this were to be adhered to Kenya
Government will close all industries in Kenya.
e. There are more than 15 Universities offering various engineering degree courses presently in Kenya with more than 300 engineering lecturers; out of these less than 5%
are registered with ERB/EBK. If the act is to be adhered to all the CEOs of these
Universities should be in jail and actually no University should offer engineering
courses in Kenya.
2. A thorough examination of the ERB/EBK as it is leads to the conclusion that the drafters intended to discourage the training of engineers in Kenya and cease engineering activities in
Kenya!!!. How then is Kenya going to develop???
3. Technology is changing all the time and the people, especially professionals, working should attend for Professional Development courses that are normally offered by the respective
professional bodies like ERB/EBK. In Kenya only engineers are luck to attend for such courses
and yet the engineers role in any engineering work in Kenya is less than 2%; this, coupled with lack of registration, is the main reason why buildings keep on collapsing in Kenya without
anybody being taken to court to answer charges.
Page 16 of 20
4. Engineering technologists, engineering technicians and Crafts persons are not presently registered and therefore are not accountable for the work they do concerning engineering
activities. Almost all engineering activities worldwide are carried out by these people. [cf. in
the medical profession in Kenya all cadres of personnel doctors/ dentists, nurses, clinical officers and lab. technologists- are registered and therefore are accountable for the work
they do]
5. While degree courses have to be approved by ERB/EBK, the technical courses have no professional body to oversee its approval and implementation. In almost all countries
worldwide more so the most developed countries (UK, USA, Australia, New Zealand, Singapore, India, Malaysia, South Korea, South Africa, Nigeria, etc.,) - all cadres are registered
and governed by acts of parliament as shown above. Why not in Kenya? What is so special
about Kenya when it comes to Engineering Profession? 6. Almost all engineering activities require the input of all the engineering team (the scientist, the
engineer, the technologists, the technician and the crafts person) i.e. they all have a role to play
and therefore each must be accountable through an act of parliament.
7. At any moment there are over a million engineering projects going on in Kenya, can the less than 600 registered engineers be able to handle all of them? It will be interesting to hear what
the ERB/EBK officials say about this. This brings the question whether The National
Construction Authority Bill, 2011 can be implemented. In practice what is going on is that the
Engineering Technology persons do the work, including designs, and the registered engineer
merely signs the drawings and takes the credit and paid very heavily for just signing ( even
though he/she may not even know where the project is situated). This is exploitation of the
Engineering Technology persons. This is one of the main reason why the EBK officials would
not like the other cadres to be registered; the engineers have become very rich out of this
corrupt practice)
8. All the above will be solved by enacting the Engineering Technologists and Technician Bill No. 45.
Page 17 of 20
How EBK Officials are killing Engineering Profession in Kenya
2. The Engineering Profession is broadly divided into two categories: Engineering and Engineering Technology (see figure below). EBK Act does not recognize the engineering technology arm of the
engineering profession, and yet this is the most important arm of Engineering as far as development of the
country is concerned. Most countries, especially the Industrialized as well as the Newly Industrialized
Countries have included the Engineering Technology in the Acts that regulated engineering and therefore,
they register all the cadres that belong to the Engineering technology i.e. Engineering Technologists,
Engineering Technicians, and Engineering Crafts persons. As examples check the following countries:
South Africa - Engineering Council of South Africa (ECSA); Nigeria Council for the regulation of Engineering in Nigeria (COREN); UK Engineering Council; Australia Engineers Australia; New Zealand IPENZ; etc. among others.
3. The EBK registrar, from time to time, has place a paid-up advertisement in the newspapers advising
employers not to employ any engineer not registered with EBK.
4. The EBK registrar, from time to time, has placed a paid-up advertisement in the newspapers advising
parents and sponsors not to sponsor students to engineering courses in most public Universities, saying that
those courses have not been approved by EBK, and yet those courses have been approved by the various
University senates according to their respective acts. In fact the officials recognize only UoN where the
EBK officials graduated from.
5. When Masinde Muliro University and Egerton University students took the ERB to court in 2012 for not
recognizing their qualifications; they were defeated and the court ordered ERB to register all of them and
pay each of them KES 200,000/-. However, to date the formers graduates have never been registered nor
paid, instead the ERB officials applied to change the name from ERB to EBK and included a clause in the
act to be allowed to accredit engineering courses in Kenya. The question is what happens to those who had
graduated before 2012 when ERB was not allowed to accredit the courses. According to the EBK officials
those graduates will never be allowed to register, and further more they will never be allowed to engage in
any engineering activities i.e. they are considered to have not been trained at all; they are just form IV
holders, and yet the Government of Kenya the owner of EBK has spent a colossal amount of money training
these graduates who are denied registration by a body that is owned by the same Government!!!!!!!.
6. EBK officials have advised Commission for University Education (CUE) to make engineering courses to
take a long time to complete with too many subjects; BSc/BEng courses take seven (7) academic years to
complete while other courses take only four (4) years to complete. In other countries similar engineering
degree courses take a maximum of five (5) academic years to complete. The result of courses taking too
long is not conducive for students to be creative and innovative brain drain. Courses with too many
subjects leave no time for self-study and therefore, students cannot be creative and/or innovative. In the
Kenyan public (not private) universities the minimum number of subjects/units per week is eight (8) while
in other countries the maximum number of subjects/units per week is six (6), but most of them have only
five (5) subjects per week, thus leaving enough time for self-study by students. Why do we want to be
different? The EBK registrar will always answer this question by saying that our standards are very high.
But I wonder what these high standards bring to Kenya when our so called engineers build or supervise
roads that last for less than three years. The Chinese with low standards (this is according to the EBK
officials; in fact EBK would not like to register an engineer trained in China because the Chinese standards
are too low) make roads that can last for a very long time. So Kenyan standards are very high but can bring
bread on to the table; we even import tooth picks from China and yet our standards are too high!!!!!!!!!!. It
is a shame.
7. As if the duration of seven years is not enough the EBK is presently lobbying too extend the duration by
adding an extra four and half (4) academic years for internship before the engineering graduates can be
considered for registration as engineers and start practicing. This effectively means that for one to qualify as
an engineer one has to take at least eleven and half (11) academic years; those who study for non-
Page 18 of 20
engineering courses four (for Bachelor degree) plus two (for Masters degree) plus three (for PhD degree),
totaling nine (9) academic years. In there a parent who can allow this scenario. This is total discouragement
from studying for engineering course and therefore a recipe for killing the Engineering profession in Kenya;
this simply means that Kenya is not ready to develop. This is been done by the EBK officials with only one
motive to safeguard engineering consultancy jobs for the chosen few and to exploit the other three cadres
from the Engineering Technology arm of Engineering Profession.
8. The EBK officials have managed to convince the Government to allow them approve engineering courses
for all Universities at a very cost of KES 600,000/- per course. This is a very controversial affair where the
officials are exploiting Universities; they can reject courses several times before passing them and every
time the course is not passed it is returned with an extra KES 600,00/-. Sometimes courses can be retained at
the EBK offices for more than two years before they look at them. This is the case with the Multimedia
University of Kenya engineering courses which have been lying at the EBK offices since 2012; this year
(2014) will be the third year Multimedia University will not have an intake in engineering courses. One of
the main reasons is that EBK does not have the capacity to approve degree courses which have been drafted
by professors as most of their members are first degree holders. The officials do not care how long they take
to approve the courses they do not care whether Multimedia has an engineering intake, after all their aim is
to discourage engineering in Kenya without saying so. I strongly suggest that the approval be taken back to
CUE where the unit in charge of accreditation can deal with this issue; the unit can always co-opt qualified
people from Universities, industry and EBK to look at the courses. In this way the EBK will not get a
chance to blackmail universities.
9. EBK Act if implemented as it is will automatically stop any engineering activities in Kenya, and the
officials know it very well. This explains why the officials have never taken a step to implement the Act as
required i.e. arrest all those unregistered engineers engaged in engineering activities, otherwise all
manufacturing and engineering service industries where more than 99% unregistered engineers are
working will be forced to wind up; even all engineering university faculties where more than 85%
unregistered engineers are lecturing will be forced to close down, thus killing the Engineering Profession in
Kenya and bring development in Kenya to a stop. This Act should be thoroughly be analyzed with all
stakeholders present. Some sections of the EBK Act {article 16 a (iii), and article 46 (1)} are contrary to
Chapter four of the Constitution on the Bill of Rights; check on Chapter Four on the Bill of Rights article 36
(2) and article 24 (1) respectively.
10. EBK officials are actually barriers to Engineering Development and hence barriers to Industrial and
Technological development which is the heart of Economic Development for this country.
11. The most important resource any country has is her human resource, and if not nurtured properly we should
forget about economic development and growth. But what EBK officials are doing is to discourage students
from studying for engineering course, and therefore, passing a message to Kenyans that we are not ready for
development. This is pure economic sabotage and we all concerned (President, Deputy President, Cabinet
Secretaries and all senior administrators, MPs and all politicians and other leaders) to urgently take the
necessary actions to stop this heinous acts. This message is particularly addressed to the two Parliamentary
Committees on Infrastructure & Transport and Education to urgently invite the EBK officials and ask them
to answer all these allegations in the presence of other stakeholders.
12. Because of the aforementioned points parents fear to sponsor their children to study for Engineering
Courses, and instead opt to sponsor them to study for other non-engineering courses. This means that
eventually Engineering will die in Kenya.
13. The only solution to saving the Engineering Profession in Kenya is to enact the Engineering Technologists
and Technicians Bill, No 45 of 2012 which already has gone through the first reading in parliament. The bill
was sponsored by Hon. Dr. Kones. The bill is available in the internet via
http://www.kenyalaw.org/klr/index.php?id=98, KNA.No.45.
Page 19 of 20
Engineering Crafts person: A person who practices or is highly skilled in a craft; artisan.Capable of dealing with specific and well-
defined engineering problems and
activities
Engineering
Technician: Capable
of dealing with well-
defined engineering
problems and
activities
Engineering
Technologist:
Capable of dealing with
broadly- defined
engineering problems
and activities
Professional
Engineer: Capable of
dealing with complex
engineering problems
and activities
If enacted the Engineering Technologists and Technicians Bill will deal with these
three cadres
Presently EBK only
deals with this cadre
In general the engineer is supposed to take the scientist research findings theories and principles- then conceptualize them with the aim of coming up with new designs, new materials and systems to serve society
better (this is normally referred to as Industrial Research as opposed to Basic or Theoretical Research that is
carried out by Engineering Scientists). This means that the Engineers work is mainly in the office and in the labs to test the new designs/materials/systems developed then pass over to Engineering Technology personnel
for implementation. In this way the country can be able to develop and move forward technologically.
Page 20 of 20
Relationship among the Five Categories/Cadres of the Engineering Profession
a) The thick lines show the normal route from the Engineering Scientist to the Engineering Crafts Person. The basic/theoretical research findings (mainly theories and principles) are passed over the Engineer who
conceptualizes them and come out with new designs, new materials, new systems, etc., tests them in labs
(i.e. deals with Industrial Research) and pass them over to the Engineering Technologist for interpretation
and implementation. The implementation is carried out by the Engineering Technicians who deal with well-
defined engineering areas. The Engineering Technicians supervise Engineering Crafts Persons who are
skilled in specific areas of engineering. Example in a Building there various engineering sections with
specific trades e.g. Refrigeration and air-conditioning section can headed by Engineering Technician with
two Engineering Crafts persons one dealing with refrigeration and the other dealing with air-conditioning. The Engineering Technologist will be in-charge of the entire project i.e. the Building.
b) The thin lines show the alternative routes from the Engineering Scientist to the Engineering Crafts Persons. The basic/theoretical research findings (mainly theories and principles) can be passed over to the
Engineering Technologist who conceptualizes them and come out with new designs, new materials, new
systems, etc., tests them in labs and interprets them for implementation. The implementation can also be
passed over directly to the Engineering Crafts Persons who will be supervised directly by the Engineering
Technologist. The Engineer can also interpret his/her industrial research findings and pass over directly to
either the Engineering Technician or the Engineering Crafts Persons for implementation. In this case the
Engineer can directly supervise the project activities. The alternatives routes are possible when the project
activities are not complex. It should also be borne in mind that there is very little difference in education
and training between the Engineer and the Engineering Technologist. When the project is not big the
Engineer or Engineering Technologist can directly supervise Engineering Crafts Persons.
By Dr. Charles M.M. Ondieki
Tel: 0722705609/0772968753;
Email: charlesondieki@yahoo.co.uk; charlesondieki@gmail.com
charlesondieki@gmail.com
Recommended