View
240
Download
2
Category
Preview:
Citation preview
FLOOR-CEILING FRAME - 1HOUR UL-F-C-8009
CONSTRUCTION TYPE / LOCATION ASSEMBLY SHT. #
A8.30
A8.30FLOOR-CEILING FRAME - 1HOUR UL-F-C-2051
A8.30FLOOR-CEILING FRAME - 1 or 2 HR UL-F-C-1009
A8.30FLOOR-CEILING FRAME - 1 or 2 HR UL-F-C-3012
A8.30WALL ASSEMBLY FRAME - 1 or 2 HR UL-W-L-1085
A8.30WALL ASSEMBLY FRAME - 1 or 2 HR UL-W-L-2098
A8.30WALL ASSEMBLY FRAME - 1 or 2 HR UL-W-L-3065
A8.30FLOOR-CEILING FRAME - 1 HOUR UL-F-C-7002
A8.30RATED WALL OUTLET BOX UL-R 14546
CONSTRUCTION TYPE / LOCATION ASSEMBLY SHT. #
A8.30FLOOR-CEILING FRAME - 1 HOUR UL-F-C-2028
A8.31WALL ASSEMBLY FRAME - 1 or 2 HR UL-W-L-3071
A8.31FLOOR-CEILING FRAME - 1 HOUR UL-F-C-2106
A8.31FLOOR-CEILING FRAME - 1 HOUR UL-F-C-2095
A8.30RATED OUTLET BOX @ TENANT WALL DETAIL
BOTHPENETRATIONS - GENERAL NOTE -----
A8.31FIRE RATED CHASE DETAIL
System No. W-J-2091
SECTION A-A
A
F Rating -- 4 HrT Rating -- 2 and 4 Hr (See Item 2)
A
13A
3B
2
3A
4
System No. W-L-3058
SECTION A-A
A
F Rating — 2 HrT Rating — 1-1/2 Hr
L Rating At Ambient — Less Than 1 CFM/Sq FtL Rating At 400 F — 4 CFM/Sq Ft
A
32
3
1A1B
1. Wall Assembly — The fire-rated gypsum wallboard/stud wall assembly shall be constructed of the materials and in the
manner specified in the individual U300 or U400 Series Wall and Partition Designs in the UL Fire Resistance Directory and
shall include the following construction features:
A. Studs — Wall framing may consist of either wood studs or steel channel studs. Wood studs to consist of nom 2 by 4 in.
lumber spaced 16 in. OC. Steel studs to be min 2-1/2 in. wide and spaced max 24 in. OC.
B. Gypsum Board* — Two layers of nom 5/8 in. thick gypsum wallboard, as specified in the individual Wall and Partition
Design. Max diam of opening is 1/2 in.
2. Cables — Max 25 pair No. 24 AWG telephone cable; polyvinyl insulation and jacket materials. One cable to be centered
within the firestop system. Cable to be rigidly supported on both sides of wall assembly.
3. Fill, Void or Cavity Material* — Sealant — Fill material forced into annular space to max extent possible. Additional fill
material to be installed such that a min 1/4 in. crown is formed around the penetrating item.
HILTI CONSTRUCTION CHEMICALS, DIV OF
HILTI INC — FS-One Sealant
*Bearing the UL Classification Mark
System No. C-AJ-1149
SECTION A-A
1. Floor or Wall Assembly -- Min 4-1/2 in. thick reinforced lightweight or normal weight (100-150
pcf) concrete. Wall may also be constructed of any UL Classified Concrete Blocks *. Max diam of
opening is 12 in.
See Concrete Blocks (CAZT) category in the Fire Resistance Directory for names of
manufacturers.
2. Through Penetrants -- One metallic pipe, conduit or tubing to be installed within the firestop
system. Pipe, conduit or tubing to be rigidly supported on both sides of floor or wall assembly. The
annular space shall be 0 in. (point contact) to max 1-1/4 in. The following types and sizes of
metallic pipes, conduits or tubing may be used:
A. Steel Pipe -- Nom 10 in. diam (or smaller) Schedule 10 (or heavier) steel pipe.
B. Iron Pipe -- Nom 10 in. diam (or smaller) cast or ductile iron pipe.
C. Conduit -- Nom 4 in. diam (or smaller) steel electrical metallic tubing or steel conduit.
D. Copper Tubing -- Nom 4 in. diam (or smaller) Type L (or heavier) copper tubing.
E. Copper Pipe -- Nom 4 in. diam (or smaller) Regular (or heavier) copper pipe.
3. Packing Material -- Min 3 in. thickness of min 4 pcf mineral wool batt insulation for nom 4 in.
diam (and smaller) pipes, conduits or tubings and a min 4 in. thickness of min 4 pcf mineral wool
batt insulation for pipe greater than nom 4 in. diam, firmly packed into opening as a permanent
form. Packing material to be recessed from top surface of floor or from both surfaces of wall as
required to accommodate the required thickness of fill material.
4. Fill, Void or Cavity Material* -- Sealant -- Min 1/2 in. thickness of fill material applied within the
annulus, flush with the top surface of floor or both surfaces of wall. At the point of contact location
between pipe and concrete, a min 1/2 in. diam bead of fill material shall be applied at the
concrete/pipe interface on the top surface of floor and on both surfaces of wall. W Rating applies
only when CP601S or CP604 sealant is used.
HILTI CONSTRUCTION CHEMICALS, DIV OF HILTI INC -- CP601S, CP604, CP606 or FS-ONE
Sealant
*Bearing the UL Classification Mark
A
F Rating -- 2 HrT Rating -- 0 Hr
L Rating At Ambient -- Less Than 1 CFM/sq ftL Rating At 400 F -- 4 CFM/sq ftW Rating -- Class I (See Item 4)
A
4
24
13
A.C
. Pac
ker L
LCPO
BO
X 50
338
JAC
KSO
NV
ILLE
BEA
CH,
FL
3224
0
FORM
ERLY
KN
OW
N A
S LO
REE
WES
T: P
H2ST
EELE
CRE
EK
2016.07.293692.14
A.C
. Pac
ker L
LCPO
BO
X 50
338
JAC
KSO
NV
ILLE
BEA
CH,
FL
3224
0
FORM
ERLY
KN
OW
N A
S LO
REE
WES
T: P
H2ST
EELE
CRE
EK
2016.07.293692.14
3692A8.31LW
1770 fennell street maitland florida 32751-7208407 660 8900 f: 407 875 9948www . cbaarchitects . com
drawn by:
job no:
reviewed by:
date:
char
lan,
bro
ck &
ass
ocia
tes,
inc.
her
eby
rese
rves
it's
com
mon
law
cop
yrig
ht a
nd o
ther
pro
perty
righ
ts in
thes
e pl
ans,
idea
s, an
d d
esig
ns.
thes
e id
eas,
des
igns
, and
pla
ns a
re n
ot to
be
repr
oduc
ed, c
hang
ed o
r cop
ied
in a
ny fo
rm o
r man
ner w
hats
oeve
r, no
r are
they
to b
e as
signe
d to
any
third
par
ty, w
ithou
t firs
t obt
aini
ng th
e ex
pres
s writ
ten
perm
issio
n fro
m c
.b.a
., in
c. w
ritte
n d
imen
sions
shal
l hav
e pr
eced
ence
ove
r sca
le d
imen
sions
.
issue history:
file:
associatesarchitects planners
MC, AP
UL ASSEMBLIES
PENETRATIONS
-
-
CDG
Recommended