Single Pole (One Location) Wireless Occupancy Sensor...

Dip Switch Settings:NOTE: To access dip switch settings, lift up the bottom of the switch pad.

Single Pole Wiring Application: • WSS10ReceiverControlSwitchisonlyintendedasa

SinglePoledevice.Multiple Location Wiring Application: • WSS0SWirelessRemoteSwitchcanbeusedfor

additionalswitches(3-wayand4-way),nowiresnecessary.

WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN OFF POWERatcircuitbreakerorfuseandtestthatpowerisoffbeforewiring!

SinglePole(OneLocation)Wireless Occupancy Sensor Products

Cat.No.WSS10,WSC04,WSC15,andWSS0SIncandescent:800W@120V–Ballast:1200VA@120V,2700VA@277V

120-277VAC,50/60Hz,Motor:1/4HP@120VINSTALLATION INSTRUCTIONS

WARNINGS AND CAUTIONS:•Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.•Ifyouareunsureaboutanypartoftheseinstructions,consultaqualifiedelectrician.•WSS10-GDxproductsdonotrequireaneutralwire,thereisaminimumrequirementof25wattsfortheseproducts.

Tools needed DescriptionSlotted/PhillipsScrewdriver ElectricalTape PliersPencilCutters Ruler WireNuts

Push in side at tab to release

Line up tabs and press in side to attach

ColorchangeoptionsareavailablefromLeviton,consultyoulocalLevitonDistributor.Tochangecolorofframe,proceedasfollows:

Changing the color of your Switch

InstallationNOTE:UsecheckboxeswhenStepsarecompleted.√

Step 1

Step 3

Step 4

Step 2 Identifying your wiring application (most common):NOTE:Ifthewiringinyourwallboxdoesnotresemblethisconfiguration,consultanelectrician.

Single Pole1. Line2. Neutral3. Ground4. Load

2

4

3

1

WIRING SWITCH: Connect wires per WIRING DIAGRAM below as follows:• Connect(Hot)wirefromwallboxtoblackwireonswitch.• Connect(Load)wireinwallboxtobluewireonswitch.• Connect(Neutral)wireinwallboxtowhitewireonswitch. NOTE:ForNoNeutralmodel,whitewirewillnotbeavailable.

BK WH

2 Black wire (BK)

Blue wire (BL)

White wire (WH)

1

3

4

BK WH

BL

Switch

Black

White

Load

Neutral (White)

Line120-277VAC,

50/60 Hz

Hot (Black)

Auto ON / Auto Off mode:Automodecanbeenabledusingthedipswitches,productcomesfromthefactoryinManualOn/AutoOff.Walk-through:canbeusedonlyinAuto-ONmodeandisrecommendedonlywhenusingbatteriesorlowvoltagepowerconnection.Timeout:2(test),10,20,30min;(Longertimedelayisrecommendedforcontinuousselfpoweringofthesensorandtoensurepacketsaresenttothereceiverswitch).

DIP SWITCH SETTINGS

-

-X

3

34

12

4

34

34

Dip Switch

10 Min Time-Out

30 Min Time-Out

20 Min Time-Out

2 Min Time-Out

ON Position

ON Position

-ON Position

ON PositionX-

ON PositionXX

Manual ON/Auto OFFWalk Through ON

X

X-

OFF Position

OFF Position

OFF Position

XOFF Position

OFF Position

-X

--

Auto ON/Auto OFFWalk Through OFF

Dip switches 1-4

Cat.No.WSS10isthereceiverswitch.Thisswitchhasasingleswitchpadthattogglestherelayanditscorrespondingload,ONandOFF.IftherelayisOFF,therelaywillturnONwhenthepush-buttonispressed,andvice-versa.TheIndicatorLEDwillblinkRedwhenaflag/packetisreceivedfromthesensororremoteswitch.NOTE: the no-neutralversionhasaminimumloadrequirementof25watts.Cat.No.WSCxxisthesensor(s).TheSensorUnitsendsaflag/packetwiththepresenceofmotiontothereceiverswitchwhichthenkeepstheloadON.Intheabsenceofmotion,theSensorUnitwillstopsendingflag/packetstothereceiverswitch;whenthereceiverswitchnolongerreceivesapacket,theTimeOutwillstart,thentime-outandturntherelayOFF.TimeDelaystartsasofthelastmotiondetectedinthespace.TheMotionIndicatorLEDwillblinkRed(1blinkperminute)everytimemotionisdetected,sendingaflag/packettothereceiver.• WSCxx & WSS10 (together):InManual-ON/Auto-Offmode,the

buttonmustbepressedtoturnthelightsON.Intheabsenceofflags/packetssentfromthesensor,thereceiverswitchwillTime-OutandturnthelightsOFF.

• WSCxx & WSS10 (together):InAuto-ON/Auto-Offmode,thesensorwillsendaflag/packettothereceivertoturnthelightsON.Intheabsenceofflags/packetssentfromthesensor,thereceiverswitchwillTime-OutandturnthelightsOFF.NOTE:ThesensormustsensemotionandsendapackettostartthetimedelayandenableAuto-Off.

• WSCxx & WSS10 (together):Theyallowthe30secondvacancyconfirmationfeaturewhichexiststoturntherelaybackONincaseoffalseOFF.

Self Powered Products:ThesensorandremoteswitchareselfpowereddevicesusingEnOceantechnology.• TheSensorutilizesasolarpanelwhichpowersthesensorfromthe

roomsambientlight.Thesensorwillstarttofunctionwithinaminuteofexposuretolight.Thetotalchargetimeforthesensorwillvarydependingonintensityoflightandlengthofexposuretolight.Theminimumlightrequirementforthesensoris40LUX(4FC).

• Theremoteswitchutilizeskineticenergyfromthemechanicalswitchwhenpushingthepad.Thisfrictionthenstoresenoughenergytotransmitanothersignalonthenextpressactionofthepad,testedover50,000cycles.

Battery option:Theuseof(3)AAAbatteries(notincluded)isnotrequiredbutcanusedinareaswherenolightisexpectedforlongperiodsoftime.Low Voltage option:The5-24VDCconnection,isprovidedandrecommendedwhenusedinareaswherenolightisexpectedforlongperiodsoftime.

Factory settings:WSS10:ManualOn/AutoOff,Walkthru=disabled,Timedelay=10min.WSCxx:Range(PIRsensitivity)=75%Factory setting operation: Whenenteringtheroom,thewirelessreceivercontrolswitchwillneedtobemanuallyturnedON.Oncelearnedintothereceiverswitch,theWirelessoccupancysensorwillsendflag/packetstothereceiverswitch,keepingthelightsonuntiltheroomisvacant.Oncethesensorstopssendingflag/packets,thereceivertimeoutwillstart,thenturnthelightsOFFaftertimeoutperiod.Time-Outs:TheSensorhasfourtime-outsettings:2(test),10,20,or30min.(longertimeoutisrecommendedforselfpoweringindarkspaces).Thevaluesoftime-outisuserselectedthroughtheuseoftheDipSwitchSettings. NOTE:Sincethesensorisonlysendingapacketeveryminute,the2minutetimedelayisnotsufficientfornormaloperation.Walk-Through Time Delay: Thewalk-throughfeatureisonlyactiveintheAuto-On/Auto-Offmodewithtimedelayof10,20or30min,isusefulwhenaroomismomentarilyoccupied.Withthisfeature,theSensorwillturnthelightsOFFshortlyafterthepersonleavestheroom.Thewalk-throughfeatureworksinthefollowingmanner:Whenapersonenterstheroom,thelightswillturnON.Ifthepersonleavestheroombeforethewalk-throughtime-outof2.5minutes,theSensorwillturnthelightsOFFwithin2.5minutesofnooccupancydetected.Iftheroomisoccupiedforlongerthan2.5minutes,theSensorwillentertheOccupiedModewiththetime-outdurationspecifiedbytheDipSwitchsetting.

WARNINGS AND CAUTIONS:•Disconnectpoweratcircuitbreakerorfusewhenservicing,installingorremovingfixture.•Usethisdeviceonlywithcopperorcoppercladwire.•Recommendedminimumwallboxdepthis2-1/2”. PK-93664-10-00-0B

FCC COMPLIANCE STATEMENT Thisdevicecomplieswithpart15oftheFCCrules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.AnychangesormodificationsnotexpresslyapprovedbyLevitoncouldvoidtheuser’sauthoritytooperatethisequipment.

LEARN MODE (to Learn devices):WhenusingtheWirelessOccupancyProductstogether,theymustbepairedtotheotherdevicestoperformasdesired.• WSC04 and WSC15-WirelessOccupancySensor(s)–haslearn

buttonondevice,underfrontplastictab• WSS10-WirelessReceiverControlSwitch-useswitchpadfor

learning• WSS0S-WirelessRemoteSwitch-useswitchpadforlearningSTEP A) Toenterprogramming,pressandholdtheReceiverControl

Switch(WSS10)switchpadfor15seconds.ThereceiverwillthenenterprogrammingandflashAMBER.

Thereare2modesinprogramming,LEARNandCLEARmodes. Tap the switch pad to toggle between the two programmingmodes

• 1AMBERLEDflash=LEARNmode • 2AMBERLEDflashes=CLEARmodeSTEP B)Selectthedesiredprogramming(LEARNorCLEAR)mode,

pressandholdthepadfor5secondstoENTERthedesiredmode (continue to step C or D).

STEP C)Pressthelearnbuttonsoneachofthedevicesyouwanttolearnintothereceiverswitch.

• Remoteswitch,youmustpresstheswitchpadtosendasignalforlearning.

• Occupancysensor,youmustpressthelearnbuttononthefrontofthesensorunderplastictabtosendasignalforlearning.

• AMBERLEDonfor2seconds=acknowledgement,deviceislearned.

NOTE:Pressthelearnbuttononcetolearn.Pressingitmorethanoncewillunlearnthedevice.

LED feedback/indicators in learn mode: • 1Redflash=nolearneddevices • 1Greenflash=1learneddevices • 2Greenflashes=2learneddevices • 3Greenflashes=3learneddevices • Etc.(upto6devices)To Un-Learn a single device:Presstheremoteswitchoroccupancysensorlearnbuttonagainandtheaddresswillberemoved. • GREENLEDonfor2seconds=deviceisunlearnedTo EXIT:(programming/learn/clear)Wait15secondsandthedevicewillautomaticallyexit.CLEAR MODE (to clear All Devices): • StartatthebeginningwithSTEPSAandBabove. • 1Redflash=nolearneddevices • MultipleGreenflashes=devicesexistSTEP D)Pressandholdtheswitchpadformorethan5seconds.After

thebuttonisreleased,theLEDwillflashredtoconfirmalllearneddeviceshavebeenclearedandthenthedevicewillexitprogramming.

NOTE: Productwillleavetheprogramminglearnorclearmodes,withoutchange,after15secondsofinactivity.

Restore Power:Restorepoweratcircuitbreakerorfuse. Installation is complete. ©2009LevitonMfgCo.,Inc. PK-93364-10-00-0B

CoveredbyoneormoreUS&ForeignPatentsandpatentspendingAllRightsIncludingTradeDressRightsReserved

For additional information, contact Leviton’s Techline at 1-800-959-6004 or visit Leviton’s website at www.leviton.com

LE

AR

N

RA

NG

E

WSC04/WSC15

WSS10

WSS0S

Push pad

Locator light

LIMITED 5 YEAR WARRANTY AND EXCLUSIONSLevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenefitofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforfiveyearsfromthepurchasedate.Leviton’sonlyobligationistocorrectsuchdefectsbyrepairorreplacement,atitsoption,ifwithinsuchfiveyearperiodtheproductisreturnedprepaid,withproofofpurchasedate,andadescriptionoftheproblemtoLeviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melvile, New York 11747.Thiswarrantyexcludesandthereisdisclaimedliabilityforlaborforremovalofthisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperlyorinanimproperenvironment,overloaded,misused,opened,abused,oralteredinanymanner,orisnotusedundernormaloperatingconditionsornotinaccordancewithanylabelsorinstructions.There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose,but ifany impliedwarranty is requiredby theapplicable jurisdiction, thedurationofanysuch impliedwarranty, includingmerchantabilityandfitness foraparticularpurpose, is limited tofiveyears.Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation.Theremediesprovidedhereinaretheexclusiveremediesunderthiswarranty,whetherbasedoncontract,tortorotherwise.

Programming: Step 5

Step 8

• Positionallwirestoprovideroominoutletwallboxfordevice.

• Ensurethattheword“TOP”isfacingupondevicestrap.

• Partiallyscrewinmountingscrewsinwallboxmountingholes.

Testing your Switch prior to mounting in wall box:

NOTE:Dresswireswithabendasshownindiagraminordertorelievestresswhenmountingdevice.

• Restorepoweratcircuitbreakerorfuse.

• PresspaduntillocatorlightisOFF.LightsshouldturnON.

If lights do not turn ON, refer to the TROUBLESHOOTING section.

Step 6

Installationmaynowbecompletedbytighteningmountingscrewsintowallbox.Attachwallplate.

Switch Mounting:TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.

Step 7

Troubleshooting• Lights Flickering - Lamphasabadconnection. - Wiresnotsecuredfirmlyunderterminalscrewsofswitch

and/orremote.• Light does not turn ON and Locator LED does not turn ON - Circuitbreakerorfusehastripped. - Lampisburnedout. - LampNeutralconnectionisnotwired.

OperationNOTE:ThelocatorlightwillilluminatewhentheloadisintheOFFpositiontofacilitateaccessinthedark.Charge time:2-4minutesdependingonstrengthoflightsourceOccupancy Sensor minimum light requirement:40LUXMin25W(Noneutralversion)Auto ON:willfunctionwith(3)AAAbatteriesindefinitelywhenambientlightispresentintheroomformorethan30minutesperday.Push Pad (Default settings)Turn ON from OFF position: Tap–LightsturnON.Turn OFF from ON position: Tap–LightsturnOFF.Cleaning:Cleanwithadampcloth.DO NOTusechemicalcleaners.