View
7
Download
0
Category
Preview:
Citation preview
State Supply ■ Saint Paul, MN ■ Toll Free: 800.772.2099 ■ Fax: 651.774.7156 ■ www.StateSupply.com
Order Online: www.StateSupply.com State Supply Co., Inc. Copyright 1987-2014 2
Spirax-Sarco Industrial Thermostatic Steam Traps
1
2
2.8”
2.0”
6.25”
4.2”
Spirax-Sarco TM600 & TM600L Use as Either Steam Trap or Air Vent
Shown as a
Thermostatic Steam trap
Shown as a
Thermostatic Air Vent
¾” Angle Inlet
Plugged.
Upside Down it’s an Air Vent!
Designed for use on steam systems operating up to 600 psi and 650° F. Ductile iron body with stainless steel diaphragm.
■ As a steam trap it removes all condensate and non-condensable gases from the equipment being trapped and returns the dis-charge toward the boiler. ½” and ¾” NPT connections.
■ Turn it upside down, plug the angle-side inlet and it’s a thermo-static air vent! Can be installed on all steam equipment up to its maximum ratings. ½” and ¾” NPT connections.
TM600 shown
DIMENSIONS
Repair Parts Guide
Model No.
Pipe Size
Max. Steam
PSI Order No.
Repair Parts 1. Cap Gasket
2. Element Set with Gasket
TM600 1/2” SG1141
SH1128 SH1137 3/4” SG1141A
TM600L 1/2” SG1142
3/4” SG1142A
600
Spirax-Sarco T250 High Pressure Steam Trap Select from Straight or Angle Pattern Connections
Dimensions
Straight Angle Pattern
The Spirax-Sarco T250 has a welded, self-adjusting stainless steel element that discharges hot condensate at approximately 20° F. below the any saturated steam temperature up to 450° F.
■ Max. Operating pressure: 250 psi ■ Max. Operating Temp: 450° F. ■ Body Construction: Cast Iron ■ Operating Internals: Stainless Steel
Model No.
Pipe Size
WGT LBS.
Pipe Pattern
Dimensions, Inches Order No.
Repair Parts
A B C D Cap Gasket (B)
Repair Kit (A thru E)
T250
1/2” 3.5 90°Angle
1.75 1.75 3.12 4.56 SG1145 SH1075C SH1060 3/4” 3.5 1.75 1.75 3.12 4.56 SG1150 SH1075C SH1070 1” 6.0 2.12 2.25 3.9 5.37 SG1165 SH1075A SH1095
1/2” 4.3 Straight
1.75 1.75 3.12 5.37 SG1143 SH1075C SH1060 3/4” 4.3 1.87 1.75 3.12 5.37 SG1144 SH1075C SH1070
Repair Parts
State Supply ■ Toll Free: 800.772.2099 ■ Fax: 651.774.7156 ■ Contact: Sales@StateSupply.com
Email: Sales@StateSupply.com State Supply Co., Inc. Copyright 1987-2014 3
Spirax-Sarco BPC32 Carbon Steel Thermostatic Traps
Model No.
Pipe Size
Pipe Conn.
WGT LBS.
Dimensions, Inches Order No.
Repair Parts
A A1 B C D F *STD
Capsule Assembly
*SUB Capsule
Assembly Cover Gasket
Screens: Blow Down
& Body
Blow Down Screen Gasket
BPC32
Standard Less
Strainer
½” NPT 3.1 3.7 5.9 3.7 2.5 0.7 — SG1010A
SH1003A SH1003C
SH1003E
Body Screen for BPC32 & BPC32Y
— ½” SW 3.1 3.7 5.9 3.7 2.5 0.7 — SG1010C — ¾” NPT 3.1 3.7 5.9 3.7 2.5 0.7 — SG1010E — ¾” SW 3.1 3.7 5.9 3.7 2.5 0.7 — SG1010G — 1” NPT 3.3 3.7 5.9 3.7 2.5 0.7 — SG1010H — 1” SW 3.3 3.7 5.9 3.7 2.5 0.7 — SG1010K —
BPC32Y
With Built-In Strainer
½” NPT 3.5 3.7 5.9 3.7 2.5 — 2.1 SG1010L SH1003G
Blow Down Screen for BPC32Y Only.
SH1003H
½” SW 3.5 3.7 5.9 3.7 2.5 — 2.1 SG1010M ¾” NPT 3.5 3.7 5.9 3.7 2.5 — 2.1 SG1010N ¾” SW 3.5 3.7 5.9 3.7 2.5 — 2.1 SG1010P 1” NPT 4.0 3.7 6.3 3.7 2.5 — 2.3 SG1010R 1” SW 4.0 3.7 6.3 3.7 2.5 — 2.3 SG1010T
SH1003
Also available in ANSI 150 or 300 flanged connections. Not shown here. All Traps listed above come with the STD operating capsule: Discharges condensate at 22° F below steam saturation temperature.
* The STD capsule opens to discharge condensate at 22° F below steam saturation temperature. The SUB capsule opens to discharge condensate at 43° F below steam saturation temperature.
These Spirax-Sarco Thermostatic Steam Traps efficiently operate at steam pres-sures up to 465 psi, and temperatures up to 572° F. The traps come equipped with a Standard (STD) operating capsule that opens to discharge hot condensate at 22° F. below saturated steam temperature. The model BPC32Y comes with an integral stainless steel strainer.
The trap should be installed on a horizontal plane with the cover at the top, and preferably with a drop leg immediately preceding the trap. When installing a socket weld model there is no need to remove the element first as long as welding is electric arc method. ANSI 150 and 300 flanges optional.
Capacities, PPH Condensate
Dimensions
Strainer Screen
Strainer Screen Gasket
Body Screen
Capsule Assembly
Includes Gasket
State Supply ■ Saint Paul, MN ■ Toll Free: 800.772.2099 ■ Fax: 651.774.7156 ■ www.StateSupply.com
Order Online: www.StateSupply.com State Supply Co., Inc. Copyright 1987-2014 4
The Spirax-Sarco SBP30LC has an all stainless steel construction, both internals and body. The welded stainless steel operating element is self-adjusting over the entire operating pressure range and will discharge condensate at approximately 18° F. below saturated steam temperature. The stainless steel operating element is resistant to water hammer and super heat up to 90° F. over saturated steam temperature can be tolerated. Typical applications include kitchen and hospital equipment, steam tracers, steam coils, steam radiators and steam main drip stations.
Spirax-Sarco TSS-300 & DTS-300 Thermostatic Steam Traps
TSS-300 & DTS-300
Both the DTS– and TSS-300 are very similar except that the TSS-300 is used where no back-up of con-densate should be tolerated - In other words, hot condensate must be quickly discharged. Therefore:
■ The TSS-300 is for critical and non-critical steam tracing systems and main drips. ■ The DTS-300 is for non-critical steam tracing systems only. ■ Either installed vertically or horizontally.
Both models feature All Stainless Steel Bodies, internals plus the following:
■ Balanced pressure operational element that discharges condensate at approximately 20 F below satu-rated steam temperature ■ Maximum operating pressure: 300 psi. Maximum operating temperature: Saturated steam temperature at 300 psi. ■ Both models “Fail” open.
TSS-300 Capacity, PPH DTS-300 Capacity, PPH
A
B
Model No.
Pipe Size NPT
WGT LBS.
Dim. inch Order No. A B
TSS-300 ½”
2.5 1.5
SG1174A ⅜” SG1174
DTS-300 ½” SG1174E ⅜” SG1174C
0.8
Order Guide - All Stainless Steel Construction. No repair parts.
Both the TTS-300 and DTS-300 are factory sealed for tamper-proof operation, and no repair parts are available.
Spirax-Sarco SBP30LC Thermostatic Steam Traps
Model No.
Pipe Size NPT
WGT LBS.
Dimensions, inches Order No. A D
SBP30LC ½”
2.2 3.1 0.75 SG1174T
¾” SG1174V
B
2.5
C
2.2
■ Maximum Operating Temp: 500° F ■ Maximum Operating Press: 435 psi ■ Tamper-proof Body, No repair parts. ■ Preferred installation: Horizontally ■ Resists water-hammer and freezing ■ Withstands up to 90° F. Superheat
State Supply ■ Toll Free: 800.772.2099 ■ Fax: 651.774.7156 ■ Contact: Sales@StateSupply.com
Email: Sales@StateSupply.com State Supply Co., Inc. Copyright 1987-2014 5
Spirax-Sarco MST21 & MST1H Thermostatic Steam Traps
Model No.
Pipe Size NPT
Capsule Open Temperature, F.
At or below steam saturation temp.
WGT LBS.
Dimensions, Inches Order No.
Repair Parts
A B C D Complete Capsule Assembly
Cover Gasket Only
MST21
¼” 40° Subcool 0.8 2.0 0.3 0.4 1.8 SG1172E SH1002A
SH1002E
¼” 18° Subcool 0.8 2.0 0.3 0.4 1.8 SG1172F SH1002C
¼” Near Steam Temp. 0.8 2.0 0.3 0.4 1.8 SG1172G SH1002
½” 40° Subcool 1.1 2.4 0.5 0.6 1.8 SG1172H SH1002A
½” 18° Subcool 1.1 2.4 0.5 0.6 1.8 SG1172K SH1002C
½” Near Steam Temp. 1.1 2.4 0.5 0.6 1.8 SG1172M SH1002
MST21H
½” 40° Subcool 1.1 2.4 0.5 0.6 1.8 SG1172N SH1002A
½” 18° Subcool 1.1 2.4 0.5 0.6 1.8 SG1172P SH1002C
½” Near Steam Temp. 1.1 2.4 0.5 0.6 1.8 SG1172R SH1002
¾” 18° Subcool 1.1 2.7 0.6 0.6 1.8 SG1172T SH1002C
¾” 40° Subcool 1.1 2.7 0.6 0.6 1.8 SG1172U SH1002A
¾” Near Steam Temp. 1.1 2.7 0.6 0.6 1.8 SG1172V SH1002
1” 18° Subcool 1.1 3.0 0.6 0.6 1.8 SG1172W SH1002C
1” 40° Subcool 1.1 3.0 0.6 0.6 1.8 SG1172X SH1002A
1” Near Steam Temp. 1.1 3.0 0.6 0.6 1.8 SG1172Y SH1002
A
D
B
C
Capacities of Condensate Discharge, PPH Repair Parts
Cover Gasket Only
Complete Capsule
Assembly
The Spirax-Sarco MST21 (standard capacity) and MST21H (higher capacity) have all stainless steel construction and can adjust to all steam operating pressures up to 304 psi.
■ Three discharge temperatures offered: 40° below steam saturation temperature; 7° below saturation and the other almost at saturation (steam) temperature. ■ Preferred installation is a vertical pattern. If installed horizontally to the ground the trap should be preceded by a short drop leg. ■ If used as an air vent, install inverted - Outlet on top. ■ Internal element withstands water hammer and temperatures to 518° F. ■ The internal element assembly and cover gasket are readily available repair parts
State Supply ■ Saint Paul, MN ■ Toll Free: 800.772.2099 ■ Fax: 651.774.7156 ■ www.StateSupply.com
Order Online: www.StateSupply.com State Supply Co., Inc. Copyright 1987-2014 6
Spirax-Sarco SMC32 & SMC32Y Bimetallic Steam Traps
Model No.
Pipe Size
Pipe Conn.
WGT LBS.
Dimensions, Inches Order No.
Repair Parts
A A1 B C D F Bimetallic Assembly
Cover Gasket Screen
Blow Down Screen Gasket
SMC32
Standard Less
Strainer
½” NPT 3.1 3.7 5.9 3.7 2.5 0.7 — SG1011
SH1040 SH1040A
SH1040C
Body Screen
for SMC32 & SMC32Y
— ½” SW 3.1 3.7 5.9 3.7 2.5 0.7 — SG1011A — ¾” NPT 3.1 3.7 5.9 3.7 2.5 0.7 — SG1011C — ¾” SW 3.1 3.7 5.9 3.7 2.5 0.7 — SG1011E — 1” NPT 3.3 3.7 5.9 3.7 2.5 0.7 — SG1011F — 1” SW 3.3 3.7 5.9 3.7 2.5 0.7 — SG1011G —
SMC32Y With
Built-In Strainer
½” NPT 3.5 3.7 5.9 3.7 2.5 — 2.1 SG1011H
SH1040E
Strainer Screen
for SMC32Y only
SH1040F
Strainer Screen Gasket
½” SW 3.5 3.7 5.9 3.7 2.5 — 2.1 SG1011K
¾” NPT 3.5 3.7 5.9 3.7 2.5 — 2.1 SG1011L
¾” SW 3.5 3.7 5.9 3.7 2.5 — 2.1 SG1011M
1” NPT 4.0 3.7 6.3 3.7 2.5 — 2.3 SG1011N
1” SW 4.0 3.7 6.3 3.7 2.5 — 2.3 SG1011P
Also available in ANSI 150 or 300 flanged connections. All Traps listed above discharge condensate slightly below steam saturation temperature.
These Spirax-Sarco SMC32 Thermostatic Steam Traps have a carbon steel body and bimetallic operating element and stainless steel internals. They efficiently op-erate at steam pressures up to 465 psi, and temperatures up to 662° F.
The trap should be installed on a horizontal plane with the cover at the top, and preferably with a drop leg immediately preceding the trap. When installing a socket weld model—There is no need to remove the element first as long as weld-ing is electric arc method. ANSI 150 and 300 flanges optional.
To expedite easy servicing of the trap please install isolating valves both upstream and down stream of the steam trap.
Capacities, PPH Condensate
Dimensions
Strainer Screen Gasket
Strainer Screen
Body Screen
Bimetallic Thermostat Assembly
Includes Gasket
Repair Parts
State Supply ■ Toll Free: 800.772.2099 ■ Fax: 651.774.7156 ■ Contact: Sales@StateSupply.com
Email: Sales@StateSupply.com State Supply Co., Inc. Copyright 1987-2014 7
Spirax-Sarco HP High Pressure Bimetallic Steam Traps Spirax Sarco Models HP45, HP80, HP100, HP150 and HP 210
Spirax-Sarco models HP45, HP80, HP100, HP150 and HP 210 are designed for very high pressure steam: Maximum steam working pressures from 652 psi (Model HP45) to 3045 psi (Model HP210).
■ Forged steel body with stainless steel operating internals and integral stainless steel strainer screen ensure both robust and efficient operation. ■ HP series (except HP45) include a check valve to prevent problems associated with backpressure. ■ All models have an external adjusting control to allow the discharge temperature of the condensate to be controlled. ■ These steam traps operate with no loss of steam and quickly expel air and large quantities of cold water on start-up.
HP45 Capacities
Sample HP150 Shown
HP80, HP100, HP150 & HP200 Capacities
Model No.
Pipe Size
Max. Work PSI
Pipe Conn
WGT LBS.
Order No.
Repair Parts
*Bimetallic Assembly
Gasket Kit
Screen Only
Check Valve
HP45
½”
652
NPT
7.6 SG1098
SH1040G
SH1040N
Includes Valve Seat,
Cover & Top Nut Gaskets
SH1040P
Not Repairable
¾” 7.6 SG1098A
1” 17.6 SG1098C
½”
SW 17.6
SG1098E
¾” SG1098F
1” SG1098G
HP80
½”
1160 SW 20.9
SG1098H
SH1040H ¾” SG1098K
1” SG1098L
HP100
½”
1450 SW 23.2
SG1098M
SH1040K ¾” SG1098N
1” SG1098P
HP150
½”
2175 SW 25.4
SG1098R
SH1040L
SH1040R
¾” SG1098T
1” SG1098U
HP210
½”
3045 SW 25.4
SG1098V
SH1040M ¾” SG1098W
1” SG1098X
SH1040T
Model Pipe Size A B C
HP45
HP80
½” 6.3 5.4 5.9 ¾” 6.3 5.4 5.9 1” 6.3 5.4 5.9
HP100 ½” 6.3 5.7 5.9 ¾” 6.3 5.7 5.9 1” 6.3 5.7 5.9 ½” 8.3 6.6 5.9 ¾” 8.3 6.6 5.9 1” 8.3 6.6 5.9
HP150
HP210 A
C
B Dimensions, inches
Model HP80 to HP210
Model HP45
Repair Parts
External Adjustment Knob to Control Temp. of Condensate
*Bimetallic Assembly
Includes All Gaskets (valve seat, cover &
top nut), Screen & Bi-Metal Element.
Check Valve
Screen
Recommended