STI 34188 Installation Manual

Safety Technology International, Inc.2306 Airport Road Waterford, Michigan 48327-1209Phone: 248-673-9898 Fax: 248-673-1246Toll Free: 800-888-4784 E-mail: info@sti-usa.comWeb: www.sti-usa.com

Safety Technology International (Europe) Ltd.Unit 49G Pipers Road Park Farm Industrial Estate RedditchWorcestershire B98 0HU England Tel: 44 (0) 1527 520 999Fax: 44 (0) 1527 501 999 Freephone: 0800 085 1678 (UK only)E-mail: info@sti-europe.com Web: www.sti-europe.com

Safety Technology International, Inc.2306 Airport Road Waterford, Michigan 48327-1209Phone: 248-673-9898 Fax: 248-673-1246Toll Free: 800-888-4784 E-mail: info@sti-usa.comWeb: www.sti-usa.com

Safety Technology International (Europe) Ltd.Unit 49G Pipers Road Park Farm Industrial Estate RedditchWorcestershire B98 0HU England Tel: 44 (0) 1527 520 999Fax: 44 (0) 1527 501 999 Freephone: 0800 085 1678 (UK only)E-mail: info@sti-europe.com Web: www.sti-europe.com

ADHESIVE BACK PCB SUPPORT(4) PROVIDED

PEEL BACKING

TO 8 CHANNEL RECEIVERSTI-34108

FEMALE JACK

MALE PLUG

24 4-CONDUCTOR CABLE(1) PROVIDED

POWER IN 12 VDC250 mA

ZONE ALERT LED

5.90 in.(150mm)

2.00 in.(51mm)

+_

FOR BOTH ENDS OFCONNECTOR ALIGN TABSON MALE PLUG TO SLOTSON FEMALE JACKAND INSERT AS SHOWN.

Zone 5 Zone 6 Zone 7 Zone 8Zone 1 Zone 2 Zone 3 Zone 4

NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC12V GND

ADHESIVE BACK PCB SUPPORT(4) PROVIDED

PEEL BACKING

TO 8 CHANNEL RECEIVERSTI-34108

FEMALE JACK

MALE PLUG

24 4-CONDUCTOR CABLE(1) PROVIDED

POWER IN 12 VDC250 mA

ZONE ALERT LED

5.90 in.(150mm)

2.00 in.(51mm)

+_

FOR BOTH ENDS OFCONNECTOR ALIGN TABSON MALE PLUG TO SLOTSON FEMALE JACKAND INSERT AS SHOWN.

Zone 5 Zone 6 Zone 7 Zone 8Zone 1 Zone 2 Zone 3 Zone 4

NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC12V GND

ADHESIVE BACK PCB SUPPORT(4) PROVIDED

PEEL BACKING

TO 8 CHANNEL RECEIVERSTI-34108

FEMALE JACK

MALE PLUG

24 4-CONDUCTOR CABLE(1) PROVIDED

POWER IN 12 VDC250 mA

ZONE ALERT LED

5.90 in.(150mm)

2.00 in.(51mm)

+_

FOR BOTH ENDS OFCONNECTOR ALIGN TABSON MALE PLUG TO SLOTSON FEMALE JACKAND INSERT AS SHOWN.

Zone 5 Zone 6 Zone 7 Zone 8Zone 1 Zone 2 Zone 3 Zone 4

NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC12V GND

INSTALLATION INSTRUCTIONS1. SnapadhesivebackPCBsupportsintoPCBasshown.

2. PeelbackingfromadhesivebackPCBsupports,placePCBindesiredpositionandpressfirmly.

INSTALLATION OF STI-34188 8-ZONE RELAY BOARDAll specifications and information shown were current as of publication and are subject to change without notice.

STI-34188 JUNE 2012

Safety Technology International, Inc.2306 Airport Road Waterford, Michigan 48327-1209Phone: 248-673-9898 Fax: 248-673-1246Toll Free: 800-888-4784 E-mail: info@sti-usa.comWeb: www.sti-usa.com

Safety Technology International (Europe) Ltd.Unit 49G Pipers Road Park Farm Industrial Estate RedditchWorcestershire B98 0HU England Tel: 44 (0) 1527 520 999Fax: 44 (0) 1527 501 999 Freephone: 0800 085 1678 (UK only)E-mail: info@sti-europe.com Web: www.sti-europe.com

Safety Technology International, Inc.2306 Airport Road Waterford, Michigan 48327-1209Phone: 248-673-9898 Fax: 248-673-1246Toll Free: 800-888-4784 E-mail: info@sti-usa.comWeb: www.sti-usa.com

Safety Technology International (Europe) Ltd.Unit 49G Pipers Road Park Farm Industrial Estate RedditchWorcestershire B98 0HU England Tel: 44 (0) 1527 520 999Fax: 44 (0) 1527 501 999 Freephone: 0800 085 1678 (UK only)E-mail: info@sti-europe.com Web: www.sti-europe.com

INSTALLATION OF STI-34188 8-ZONE RELAY BOARDAll specifications and information shown were current as of publication and are subject to change without notice.

STI-34188 JUNE 2012

A

AFTER DRILLING, CUT OUT THIS AREAUSING SIDE CUTTERS OR KNIFE

CABLE JACK TO RELAY BOARD

DRILL 5/32 in. (4mm)DIAMETER HOLE

BE SURE TO ROUTE CABLE AROUND POST AS

SHOWN AND PLUG CABLE IN TO CONNECTOR

CIRCUIT BOARD MOUNTING SCREW

DETAIL A

ALIGN TOASSEMBLE

A

AFTER DRILLING, CUT OUT THIS AREAUSING SIDE CUTTERS OR KNIFE

CABLE JACKTO RELAY BOARD

DRILL 5/32 in. (4mm)DIAMETER HOLE

BE SURE TO ROUTE CABLE AROUND POST AS

SHOWN AND PLUG CABLE IN TO CONNECTOR

CIRCUIT BOARDMOUNTING SCREW

DETAIL A

ALIGN TOASSEMBLE

CABLE INSTALLATION TO RECEIVER1. Removecircuitboardfrombasebyremovingcircuitboardmountingscrew.

2. Drill5/32in.diameterholeinbaseasshown(circuitboardmustberemoved.)

3. Afterdrilling,cutoutareaasshownusingsidecuttersorknife.

4. Routecableasshownandconnectcabletojackoncircuitboard.

5. Whilereplacingcircuitboard,gentlypullcablefrombottomofbasetotakeupanyslackincableoccurredduringinstallation.

SPECIFICATIONS Standby:12VDC;0.01mA MaxOperating:12VDC;164mA FormCContactRating(resistive):120VAC,3A;28VDC,3A

WARRANTYOneyearwarrantyonelectromechanicalandelectroniccomponents.Electronicwarrantyformatwww.sti-usa.com/wc14.