View
8
Download
0
Category
Preview:
Citation preview
StoTherm
®
ci XPS
System Components
Detail No.: 53s.00.2D
Date: February 2019
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20 or
Owens Corning Foamular
CI-C Board)
Sto TurboStick Adhesive
StoGuard® Air and Moisture
Barrier
Sheathing
Light Gauge Steel
Stud Framing
Batt Insulation
Property of Sto Corp. All Rights Reserved.
Sto Finish
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Primer
(Optional)
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
StoTherm
®
ci XPS
System Components: Ultra-High Impact Resistance
Detail No.: 53s.01.2D
Date: February 2019
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20
or Owens Corning
Foamular CI-C
Insulation Board)
StoTurboStick
Adhesive
StoGuard® Air and Moisture
Barrier
Sheathing
Light Gauge Steel
Stud Framing
Batt Insulation
Property of Sto Corp. All Rights Reserved.
Sto Finish
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- StoTurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh ArmorMat
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Primer
(Optional)
Sto Base Coat
(with Sto ArmorMat Mesh Embedded)
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
StoTherm
®
ci XPS
Termination at Grade-
Sheathing Flush with Foundation or Slab Edge
Detail No.: 53s.03A.2D
Date: February 2019
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20
or Owens Corning
Foamular CI-C
Insulation Board)
Sto TurboStick
Adhesive
StoGuard® Air and
Moisture Barrier
Sto Back Wrap
Z-Flashing
Backer Rod & Sealant
with Weeps
Sto Finish
Sto Primer
(Optional)
Batt Insulation
Light Gauge
Steel Stud Framing
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- StoTurboStick Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Property of Sto Corp. All Rights Reserved.
StoGuard® Transition
Component
StoGuard® Transition
Component
Sheathing
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
StoTherm
®
ci XPS
Termination at Grade-
Sheathing Overlapping Slab or Foundation
Detail No.: 53s.03B.2D
Date: February 2019
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Property of Sto Corp. All Rights Reserved.
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20
or Owens Corning
Foamular CI-C
Insulation Board)
Sto TurboStick
Adhesive
StoGuard® Air and
Moisture Barrier
Sheathing
Z-Flashing
Backer Rod & Sealant
with Weeps
Sto Finish
Sto Primer
(Optional)
Batt Insulation
Light Gauge
Steel Stud Framing
StoGuard® Transition
Component
StoGuard® Transition
Component Top Coated
with 2 Coats of StoColor
Acryl Plus
Sto Back Wrap
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
StoTherm
®
ci XPS
Aesthetic Feature Band
Detail No.: 53s.04.2D
Date: February 2019
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- StoTurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Sto Flexyl Mesh
Where Applicable
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Finish
Sto Flexyl
(Return Vertically 102mm (4")
Above and Below Feature
Band. Sto Mesh or Sto Detail
Mesh Embedded)
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20 or
Owens Corning
Foamular CI-C
Insulation Board)
Sto TurboStick
Adhesive
StoGuard® Air and
Moisture Barrier
Sheathing
Light Gauge Steel
Stud Framing
Batt Insulation
Sto Primer
(Optional)
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
StoTherm
®
ci XPS
Aesthetic Reveal - Option 1
Detail No.: 53s.05A.2D
Date: February 2019
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Sto Finish
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20
or Owens Corning
Panel Foamular CI-C
Insualtion Board)
Sto TurboStick
Adhesive
StoGuard® Air and
Moisture Barrier
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Primer
(Optional)
Sheathing
Light Gauge Steel
Stud Framing
Batt Insulation
Sto Base Coat
(with Sto Detail Mesh Embedded)
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
StoTherm
®
ci XPS
Aesthetic Reveal - Option 2
Detail No.: 53s.05B.2D
Date: February 2019
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Sto Finish
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20
or Owens Corning
Foamular CI-C
Insulation Board)
Sto TurboStick
Adhesive
StoGuard® Air and
Moisture Barrier
Sto Primer
(Optional)
Sheathing
Light Gauge Steel
Stud Framing
Batt Insulation
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Base Coat
(with Sto Detail Mesh Embedded)
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Batt Insulation
Detail No.: 53s.23.2D
Date: February 2019
StoTherm
®
ci XPS
Window Sill / Receptor Style
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insualtion
(Dow Panel Core 20
or Owens Corning
Foamular CI-C
Insulation Board)
Sto TurboStick
Adhesive
Sto Finish
Sto Primer
(Optional)
Sealant
Sheathing
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sill Pan Flashing
StoGuard® Air and
Moisture Barrier
Rough Opening
Protection
Light Gauge Steel
Stud Framing
Fillet Sealant
Sto Back Wrap
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Fillet Sealant
Detail No.: 53s.24.2D
Date: February 2019
StoTherm
®
ci XPS
Window Head / Receptor Style
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Light Gauge Steel
Stud Framing
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Corning Panel Core
20 or Owens Corning
Foamular CI-C
Insulation Board
Sto TurboStick Adhesive
Sto Finish
Sto Primer
(Optional)
Sheathing
Head Flashing
StoGuard® Air and
Moisture Barrier
Backer Rod
and Sealant with Weeps
Rough Opening Protection
Batt Insulation
Sto Back Wrap
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Detail No.: 53s.25.2D
Date: February 2019
StoTherm
®
ci XPS
Window Jamb / Receptor Style
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Base Coat
(with Sto Mesh Embedded)
Sto Finish
Sto Primer
(Optional)
Backer Rod
and Sealant
Light Gauge Steel
Stud Framing
SheathingStoGuard® Air and
Moisture Barrier
XPS Insulation (Dow Corning Panel
Core 20 or Owens Corning Foamular
CI-C Insulation Board)
Sto TurboStick Adhesive
Rough Opening Protection
Sto Back Wrap
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
StoTherm
®
ci XPS
Soffit: Insulated and Unvented
Detail No.: 53s.30.2D
Date: February 2019
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Corning
Panel Core 20 or
Owens Corning
Foamular CI-C
Insulation Board)
Sto TurboStick
Adhesive
StoGuard® Air and
Moisture Barrier
Light Gauge Steel
Stud Framing
Sto Finish
Sto Primer
(Optional)
Sheathing
Batt Insulation
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Property of Sto Corp. All Rights Reserved.
Sto Drip Edge
Profile
Nominal (10mm)
3
8
inch
Gap for Drainage
Dissimilar Material or
Wall Construction
Backer Rod
and Sealant
Sto Back wrap
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
StoTherm
®
ci XPS
Soffit: Uninsulated and Vented
Detail No.: 53s.31.2D
Date: February 2019
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
XPS Insulation
(Dow Panel Core 20
or Owens Corning
Foamular CI-C
Insulation Board)
Sto TurboStick
Adhesive
StoGuard® Air and
Moisture Barrier
Light Gauge Steel
Stud Framing
Sheathing
Dissimilar Material
or Wall Construction
Backer Rod and
Sealant
Soffit Vent
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Base Coat
(with Sto Mesh Embedded)
Sto Finish
Sto Primer
(Optional)
Sto Drip Edge
Profile
Nominal (10mm)
3
8
inch
Gap for Drainage
Sto Back wrap
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
StoTherm
®
ci XPS
Floor Line Without Deflection
Detail No.: 53s.40.2D
Date: February 2019
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20 or
Owens Corning Foamular
CI-C Insulation Board)
Sto TurboStick Adhesive
StoGuard® Air and
Moisture Barrier
Sheathing
Light Gauge Steel
Stud Framing
Batt Insulation
Sto Primer
(Optional)
Sto Finish
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Detail No.: 53s.41A.2D
Date: February 2019
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20
or Owens Corning
Foamular CI-C
Insulation Board
(Pre-wrapped or Backwrapped)
Sto TurboStick
Adhesive
StoGuard®
Air and Moisture
Barrier
Sto Finish
Sto Primer
(Optional)
Backer Rod and
Sealant with Weeps
Cant Bead of Sto
RapidGuard
StoGuard® Transition
Membrane Embedded
in StoGuard® Air and
Moisture Barrier
StoTherm
®
ci XPS
Floor Line With Deflection - Drainage at Floor Line
Sto Backwrap
Sheathing
Light Gauge Steel
Stud Framing
Batt Insulation
Slotted Deflection
Track
Backer Rod
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
StoTherm
®
ci XPS
Floor Line With Deflection - No Drainage at Floor Line
Detail No.: 53s.41B.2D
Date: February 2019
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20
or Owens Corning
Foamular CI-C
Insulation Board
Sto TurboStick
Adhesive
StoGuard®
Air and Moisture
Barrier
Sheathing
Light Gauge Steel
Stud Framing
Batt Insulation
Sto Finish
Sto Primer
(Optional)
Slotted Deflection
Track
Backer Rod
Backer Rod and
Sealant
StoGuard® Transition
Membrane Embedded
in StoGuard® Air and
Moisture Barrier
Sto Back Wrap
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
StoTherm
®
ci XPS
Vertical Expansion Joint in Back-Up Wall
Detail No.: 53s.52A.2D
Date: February 2019
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation (Dow Corning
Panel Core 20 or Owens Corning
Foamular CI-C Insulation Board
(Pre-wrapped or Backwrapped)
Sto TurboStick Adhesive
StoGuard® Air and Moisture Barrier
Sto Finish
Sto Primer
(Optional)
Backer Rod and Sealant
StoGuard® Transition Membrane Embedded in
StoGuard® Air and Moisture Barrier
Sheathing
Light Gauge Steel
Stud Framing
Batt Insulation
Plan
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
StoTherm
®
ci XPS
Termination at Parapet
Detail No.: 53s.60.2D
Date: February 2019
®
Metal Coping
StoGuard® Detail Component
Embedded in StoGuard Air and
Moisture Barrier
Sto Finish
Sto Primer
(Optional)
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20
or Owens Corning
Foamular CI-C
Insulation Board
(Pre-wrapped or Backwrapped)
Sto TurboStick
Adhesive
StoGuard® Air and
Moisture Barrier
Sheathing
Light Gauge Steel
Stud Framing
Roof
Membrane
Sto Finish
Sto Primer
Sto Base Coat
(with Sto Mesh Embedded)
XPS
Insulation
(Pre-wrapped or Backwrapped)
Z-Flashing
Batt Insulation
Fillet Bead of
Sealant
Fillet Bead
of Sealant
Wood Blocking
Sto TurboStick
Adhesive
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Backer Rod &
Sealant
with Weeps
Roof Membrane
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow panel Core 20 or
Owens Corning Foamular
CI-C Insulation Board)
(Pre-wrapped or Backwrapped)
Sto TurboStick Adhesive
StoGuard® Air and
Moisture Barrier
Sto Finish
Sto Primer
(Optional)
Roof Membrane
StoGuard® Detail
Component
Flashing
Sheathing
StoTherm
®
ci XPS
Diverter Flashing at Roof Abutment
Detail No.: 53s.62.2D
Date: February 2019
Drainage Strip
Sto Back Wrap
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocanada.com
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
StoTherm
®
ci XPS
Gravel Stop
Detail No.: 53s.63.2D
Date: February 2019
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20 or
Owens Corning
Foamular CI-C
Insulation Board
(Pre-wrapped or Backwrapped)
StoTurboStick
Adhesive
StoGuard® Air and
Moisture Barrier
Sto Finish
Sto Primer
(Optional)
6mm (
1
4
") Min. Gap
Between Top of EPS
Insulation Board and
Wood Blocking
StoGuard® Transition
Component
Gravel Stop
Gravel Roof Ballast
Fillet Bead of Sealant
Continuous Cleat
Roof Membrane
Wood Blocking
Sheathing
Light Gauge Steel
Stud Framing
Batt Insulation
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
IMPORTANT: Components not identified
as Sto are furnished by other manufacturers
and are not necessarily installed by trades
who install Sto products. Refer to project
Notes:
1. StoTherm ci XPS
System Components:
- StoGuard Air and
Moisture Barrier
- Sto TurboStick
Adhesive
- XPS Insulation Board
- Sto Mesh
- Sto Base Coat
- Sto Primer (optional)
- Sto Finish
- Refer to StoTherm
ci XPS System
Bulletins and
Specifications, Sto
Product Bulletins,
Tech Hotlines, and
Sto Installation and
Maintenance Guides
for complete
information.
- Refer to applicable
ICC Evaluation
Reports for building
code compliance
information.
StoTherm
®
ci XPS
Scupper Penetration
Detail No.: 53s.65.2D
Date: February 2019
Sto Base Coat
(with Sto Mesh Embedded)
XPS Insulation
(Dow Panel Core 20
or Owens Corning
Foamular CI-C
Insulation Board
(Pre-wrapped or Backwrapped)
Sto TurboStick Adhesive
StoGuard® Air and
Moisture Barrier
Sto Finish
Sto Primer
(Optional)
Scupper
Backer Rod and Sealant
StoGuard® Air and
Moisture Barrier
Sheathing
Light Gauge Steel
Stud Framing
Batt Insulation
StoGuard® Detail
Component
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a
qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp.
disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an
improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities
beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious
damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED
EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S
WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing
and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Recommended