View
13
Download
0
Category
Preview:
Citation preview
Standard STD 101-0005 Volvo Group
Issue date March 2021 Issue 18 Page 1 (31)
The English language version is the original and
the reference in case of dispute.
Den engelska språkversionen är originalversion
och ska åberopas i händelse av tvist.
BASIC RULES FOR REPRESENTATION GRUNDREGLER FÖR REPRESENTATION
Symbols, designations and general drawing methods
Symboler, beteckningar och allmänt ritsätt
Orientation Orientering
This issue differs from issue 17 in that: Denna utgåva skiljer sig från utgåva 17 genom att:
− The reference to STD 105-0002 in the beginning of section 7 has been changed to STD 105-0009.
− Section 12, “Welding”, has been reworked.
− Hänvisningen till STD 105-0002 i inledningen
till avsnitt 7 har bytts till STD 105-0009.
− Avsnitt 12, ”Svetsning”, har omarbetats.
Contents Innehåll
1 Scope and field of application .................... 2
2 General rules on drawing data ................... 3
3 Projection methods and cutting planes .... 3
4 Lines, points, surfaces and markings ....... 5
5 Simplified representation of machine elements ........................................................ 8
6 Dimensioning ............................................. 11
6.1 General dimensioning .................................. 11
6.2 Symbols in connection with dimensions ...... 13
6.3 Marking of requirements .............................. 15
6.4 Requirements on edges ............................... 16
7 Geometrical product speci-fications (GPS) – Tolerances and surface texture .. 17
7.1 Dimensional tolerances ................................ 17
7.2 Geometrical tolerances and datums ............ 18
7.3 Surface texture ............................................. 22
8 Special characteristics .............................. 23
9 Significant characteristics for regulatory compliance ................................................. 24
10 Documentation requirements .................. 24
11 Hardness and case depth ......................... 25
12 Welding ...................................................... 27
13 Screw threads ............................................ 28
1 Omfattning och tillämpning ......................... 2
2 Allmänna regler om ritningsdata ................... 3
3 Projektionsmetoder och snittplan .............. 3
4 Linjer, punkter, ytor och markeringar......... 5
5 Förenklad ritning av maskin-element ......... 8
6 Måttsättning ................................................11
6.1 Måttsättning allmänt......................................11
6.2 Symboler i samband med mått .....................13
6.3 Markering av krav .........................................15
6.4 Krav på kanter ..............................................16
7 Geometriska produktspeci-fikationer (GPS) – Toleranser och ytstruktur ............17
7.1 Dimensionstoleranser ...................................17
7.2 Form- och lägetoleranser och referenser .....18
7.3 Ytstruktur ......................................................22
8 Speciella egenskaper .................................23
9 Viktiga egenskaper för uppfyllande av lagar och bestämmelser ......................................24
10 Dokumentationskrav .................................24
11 Hårdhet och härddjup ................................25
12 Svetsning ....................................................27
13 Gängor ........................................................28
Standard STD 101-0005 Volvo Group
Issue 18 Page 2 (31)
14 Moulded parts ............................................ 29
15 Other drawing symbols ............................ 30
16 Information in the drawing sheet blocks 31
17 Reference to this standard ....................... 31
14 Formgjorda artiklar ....................................29
15 Andra ritningssymboler ............................30
16 Uppgifter i fälten på ritnings blanketten.31
17 Hänvisning till denna standard ...............31
1 Scope and field of application 1 Omfattning och tillämpning
This standard describes graphic symbols, designa-
tions (e.g. dimensioning and tolerances) as well as
examples of drawing methods. The standard also
refers to Volvo Group standards and ISO standards
that give a complete definition of the representations
shown.
Denna standard beskriver grafiska symboler,
beteckningar (t.ex. måttsättning och toleranser) samt
exempel på ritsätt. Standarden hänvisar även till
Volvostandarder eller ISO-standarder som ger en
fullständig definition av visade angivelser.
In section 2, a number of basic and general rules
concerning the interpretation of drawings are stated.
I avsnitt 2 anges ett antal allmänna och grund-
läggande regler rörande tolkning av ritningar.
When this standard is referred to on drawings: Genom hänvisning till denna standard på ritning:
− the requirements specified in the standards
that are indicated in the column “Established
by standard” apply
− gäller krav enligt de standarder som anges i
kolumnen ”Fastställd i standard”
− it is possible to interpret the indications that
the standard gives examples of.
− är det möjligt att tolka de angivelser som
standarden ger exempel på.
The standards which are referred to apply within the
Volvo Group and it shall be noted that they can
include more ways to indicate than what is shown in
this standard.
De standarder som hänvisas till gäller inom Volvo-
koncernen och kan innehålla fler möjliga ritsätt än
vad som visas i denna standard.
In certain cases, the specific drawing methods are
established by this standard only.
I vissa fall är de specifika ritsätten endast fastställda
genom denna standard.
With the exception of those cases when this stan-
dard establishes a specific drawing method, the stan-
dard only provides a simplified explanation of the
respective drawing indication. For a complete
interpretation, the standard referred to in connection
with the respective example always applies.
Med undantag för de fall där denna standard fast-
lägger ett specifikt ritsätt ger standarden endast en
förenklad förklaring av respektive ritningsangivelse.
För fullständig tolkning gäller alltid den standard som
hänvisas till i anslutning till respektive exempel.
In case of any discrepancy between the indications
given in this standard and the standards referred to
for full interpretation, the latter always apply.
Vid eventuella skiljaktigheter mellan angivelser i den-
na standard och de standarder som angetts för deras
tolkning, gäller alltid de senare.
If a drawing refers to a standard that conflicts with a
standard referred to in the body of STD 101-0005,
then the standard noted on the drawing shall have
priority.
Om en ritning hänvisar till en standard som är
motstridig till en standard som åberopas i
STD 101-0005 ska den standard som angetts på
ritningen ha företräde.
Standard STD 101-0005 Volvo Group
Issue 18 Page 3 (31)
2 General rules on drawing data 2 Allmänna regler om ritningsdata
Unless otherwise stated on the drawing or in other
design-engineering documentation, dimensions are
given in millimetres.
Om inget annat angetts på ritningen eller i annan
konstruktionsteknisk dokumentation är måttuppgifter
uttryckta i millimeter.
Unless otherwise indicated, generally or for a single
piece of information, the technical documentation
represents the object in its finished condition.
Om inget annat angetts, generellt eller för enskild
uppgift, återger det tekniska underlaget objektet i sitt
färdiga utförande.
The only exception to the rule about finished
condition is surface coated M-threads, where the
tolerance applies before any surface coating.
Enda undantaget från regeln om färdigt utförande är
ytbelagda M-gängor, där toleransen gäller före
eventuell ytbeläggning.
Scale
Unless otherwise indicated generally on the drawing,
a main scale of 1:1 has been applied. A locally
indicated scale only applies to the view or section
concerned.
Skala
Om inget annat angetts generellt på ritningen, har
huvudskala 1:1 tillämpats. En lokalt angiven skala
gäller endast berörd vy eller berört snitt.
3 Projection methods and cutting planes
3 Projektionsmetoder och snittplan
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Principle / Princip
C
B
D
A
The arrow method. Layout of views
according to the reference arrow method /
Pilmetoden. Vyplacering enligt metod med
riktningspilar
ISO 128-30:2001
1
Method E. First angle projection method /
Metod E. Första kvadrantens projektions-
metod
ISO 128-30:2001
Method A. Third angle projection method /
Metod A. Tredje kvadrantens projektions-
metod
ISO 128-30:2001
Standard STD 101-0005 Volvo Group
Issue 18 Page 4 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Drawing and dimensioning in axonometric
representation /
Ritning och måttsättning i axonometrisk
representation
STD 101-0002
A
A
Indication of cutting plane /
Markering av snittplan
ISO 128-40:2001
X2217
Indication of a cutting plane in a coordinate
system (with the coordinate for the cutting
plane) when the position of the cutting plane
is parallel with one of the coordinate axes /
Beteckning av snittplan i ett koordinatsystem
(med koordinaten för snittplanet) då
snittplanet är parallellt med någon av
koordinataxlarna
STD 5023,511
Standard STD 101-0005 Volvo Group
Issue 18 Page 5 (31)
4 Lines, points, surfaces and markings
4 Linjer, punkter, ytor och markeringar
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
General use and meaning of lines /
Linjers allmänna användning och betydelse
ISO 128-24:2014
Partial view of a symmetrical object. Two
alternative methods of presentation /
Delvy av symmetriskt objekt. Två alternativa
ritsätt
ISO 128-24:2014
Interrupted views. Two alternative methods of
presentation /
Brutna vyer. Två alternativa ritsätt
ISO 128-24:2014
Outline before forming (in this case before
bending) /
Kontur före bearbetning (i detta fall före bock-
ning)
ISO 128-24:2014
Standard STD 101-0005 Volvo Group
Issue 18 Page 6 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Indication of outline of an adjacent part /
Markering av kontur för intilliggande objekt
ISO 128-24:2014
Indication of trajectories and alternative or ex-
treme positions for movable parts /
Markering av bana för rörelse och alternativt
eller extremt läge för rörlig del
ISO 128-24:2014
Indication of square surfaces and ends /
Markering av fyrkantiga ytor och ändar
ISO 128-24:2014
Leader lines / Hänvisningslinjer ISO 128-22:1999
Basic representation of areas of cuts and
sections /
Allmän angivelse av snittmarkerade områden
ISO 128-50:2001
Indication of sheet metal thickness in thin-
walled product design in view and section,
respectively /
Markering av plåttjocklek på skalkonstruk-
tioner i vy respektive snitt
STD 5023,511
Standard STD 101-0005 Volvo Group
Issue 18 Page 7 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
A B C
Indication of points and lines in thin-walled
product design /
Markering av punkter och linjer på skalkon-
struktioner
STD 5023,511
Indication of mating surfaces to mating parts /
Markering av passningsyta till motgående
artikel
STD 5023,511
Visible mating surface / Synlig passningsyta
Hidden mating surface / Skymd passningsyta
Indication of fluid in section /
Markering av vätska i snitt
Established by this
standard /
Fastställd genom denna
standard
Standard STD 101-0005 Volvo Group
Issue 18 Page 8 (31)
5 Simplified representation of machine elements
5 Förenklad ritning av maskin-element
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Representation of screw threads /
Ritning av gängor
External visible screw threads /
Utvändiga synliga gängor
ISO 6410-1:1993
Internal hidden screw threads /
Invändiga skymda gängor
Section through internal screw threads /
Snitt genom invändiga gängor
Representation of gears / Ritning av kuggar
ISO 2203:1973
Symbols for gear type and direction /
Symboler för kuggtyp och riktning
Helical to the right and to the left,
respectively /
Snedkugg höger respektive vänster
Double helical / Dubbel snedkugg
Spiral / Bågkugg
ISO 2203:1973
Standard STD 101-0005 Volvo Group
Issue 18 Page 9 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Representation of splines and serrations /
Ritning av splines och serrationer
Symbol for / Symbol för:
Straight-sided splines /
Splines med rak profil
Involute splines and serrations /
Evolventsplines och serrationer
ISO 6413:1988
A) B) C)
General simplified representation of dynamic
seals /
Allmänt förenklad ritning av dynamiska
tätningar:
A) Sealing direction of no importance /
Tätningsriktning saknar betydelse
B) Sealing direction (in the direction of the
arrow) / Tätningsriktning (i pilens riktning)
C) Exact contour shown / Verklig kontur visad
ISO 9222-1:1989
Detailed simplified representation of lip type
seals (radial seals) /
Detaljerad förenklad ritning av radialtätningar:
Rotary shaft seal without dust lip /
Tätning utan dammtunga för roterande
axel
ISO 9222-2:1989
Seal without dust lip for stationary shaft
and rotary housing /
Tätning utan dammtunga för stillastående
axel och roterande hus
Rotary shaft seal with dust lip /
Tätning med dammtunga för roterande
axel
Rotary shaft seal with dust lip (double-
acting) /
Tätning med dammtunga för roterande
axel (dubbelverkande)
Standard STD 101-0005 Volvo Group
Issue 18 Page 10 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Seal with dust lip for stationary shaft and
rotary housing /
Tätning med dammtunga för stillastående
axel och roterande hus
Detailed simplified representation of axial seals / Detaljerad förenklad ritning av axialtätningar
Rotary shaft axial seal / Axialtätning för roterande axel
ISO 9222-2:1989
A) B) C) D)
Detailed simplified representation of seals for
reciprocating movements (piston rod seals) /
Detaljerad förenklad ritning av tätningar för
fram- och återgående rörelser (kolvstångs-
tätningar):
ISO 9222-2:1989
A) U-cups / U-manschetter
B) V packing sets / V-tätningssats
C) V-rings / Hattmanschetter
D) Wipers / Avstrykare
Detailed simplified representation of labyrinth
seals /
Detaljerad förenklad ritning av labyrinttätningar
ISO 9222-2:1989
A) B)
Simplified representation of rolling bearings /
Förenklad ritning av rullningslager
Normally drawn in accordance with A). B)
shows an example of simplified representation
showing the exact outline of the bearing /
Ritas normalt enligt A). B) visar exempel på
förenklad ritning där lagrets verkliga kontur
visas
ISO 8826-1:1989
Guide pin, guide hole, centre of gravity / Styrpinne, styrhål, tyngdpunkt
Established by this standard / Fastställd genom denna standard
Standard STD 101-0005 Volvo Group
Issue 18 Page 11 (31)
6 Dimensioning 6 Måttsättning
6.1 General dimensioning 6.1 Måttsättning allmänt
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Dimensioning, general principles /
Måttsättning, allmänna regler
ISO 129-1:2018
Dimensioning of angular dimensions /
Måttsättning av vinkelmått
ISO 129-1:2018
Indication of auxiliary dimensions /
Markering av hjälpmått
ISO 129-1:2018
Indication of arc dimensions /
Markering av bågmått
ISO 129-1:2018
Origin indication in superimposed running
dimensioning /
Nollpunkt vid förenklad baslinjemåttsättning
ISO 129-1:2018
Framed dimensions / Inramade mått:
Theoretically exact dimensions (TEDs) when
using geometrical tolerances /
Teoretiskt riktiga mått (TEDs) vid tillämpning av
form- och lägetoleranser
ISO 1101:2017
Setting dimension, gauge dimension for
production and inspection. These dimensions
shall be considered as having no tolerances /
Inställningsmått, tolkmått för produktion och
kontroll. Dessa mått betraktas som toleranslösa
Standard STD 101-0005 Volvo Group
Issue 18 Page 12 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Coordinate systems for heavy vehicles /
Koordinatsystem för tunga fordon
A) Z coordinate in the main coordinate
system (M) /
Z-koordinat i huvudkoordinatsystemet (M)
B) Z coordinate in a separate coordinate
system for the engine (E). There are also
separate systems for the cab (C) and
the frame (F) /
Z-koordinat i separat koordinatsystem för
motor (E). Separata system finns även
för hytt (C) och ram (F)
C) X coordinate of any coordinate system
where the system designation in question,
e.g. M, E or C, may be omitted from the
coordinate circle and alternatively be
indicated with a text note on the drawing /
X-koordinat från vilket koordinatsystem
som helst där beteckning av aktuellt
koordinatsystem, t ex. M, E eller C, kan
utelämnas i koordinatballongen och istället
anges med en textnot på ritningen
STD 5026,1
Coordinate systems for heavy vehicles, special
application for buses where the X-axis has two
origins /
Koordinatsystem för tunga fordon, särskild
tillämpning för bussar där X-axeln har två
nollpunkter
A) Origin for the X-axis through the front axle
/ X-axelns nollpunkt genom framaxeln
B) Origin for the X-axis through the rear axle /
X-axelns nollpunkt genom bakaxeln
STD 5026,1
Indication of coordinates that are not in even
hundreds /
Angivelse av koordinater som ej är jämna
hundratal
STD 5026,1
Standard STD 101-0005 Volvo Group
Issue 18 Page 13 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
F6
F11
Numbering of holes / Hålnumrering
Holes designated by letters and figures where: /
Hål betecknas med bokstäver och siffror där:
T = view from above / vy uppifrån
B = view from below / vy underifrån
F = front view (principal view) /
vy framifrån (huvudvy)
R = view from the rear / vy bakifrån
RH = view from the right / vy från höger
LH = view from the left / vy från vänster
STD 101-0004
6.2 Symbols in connection with dimensions
6.2 Symboler i samband med mått
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Diameter / Diameter ISO 129-1:2018
R Radius / Radie ISO 129-1:2018
Square / Kvadrat ISO 129-1:2018
Indication of taper / Angivelse av kona ISO 3040:2009
SR Spherical radius / Sfärisk radie ISO 129-1:2018
S Spherical diameter / Sfärisk diameter ISO 129-1:2018
x Number of equal elements, for example 5x 10
for five times the dimension 10 /
Antalet lika element, exempelvis 5x 10 för fem
gånger måttet 10
ISO 129-1:2018
Standard STD 101-0005 Volvo Group
Issue 18 Page 14 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Simplified indication of slotted hole / Förenklad
angivning av avlångt hål
Example / Exempel:
Established by this standard / Fastställd genom denna standard
Simplified indication of rectangular shape /
Förenklad angivning av rektangulär form
Example / Exempel:
Established by this standard /
Fastställd genom denna standard
Standard STD 101-0005 Volvo Group
Issue 18 Page 15 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
CL Centre line (when needed for unambiguity) /
Centrumlinje (när så behövs för entydighet)
When several centre lines coincide, it may also
be necessary to designate the feature to which
the centre line applies, see example /
När flera centrumlinjer sammanfaller kan det
även vara nödvändigt att beteckna elementet
för vilket centrumlinjen gäller, se exempel
Established by this standard / Fastställd genom denna standard
6.3 Marking of requirements 6.3 Markering av krav
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
A) B)
Indication of a partial requirement, for
example hardening /
Markering av partiellt krav, exempelvis
hardening
When the extension of the requirement is
of no importance or when it is obvious, the
dimensioning can be excluded, see
figure A) /
Är kravets utsträckning oväsentlig eller
självklar utelämnas måttsättning,
se figur A)
When needed, the special requirement
shall be dimensioned, see figure B) /
Vid behov måttsätts det speciella kravet,
se figur B)
ISO 128-24:1999
Standard STD 101-0005 Volvo Group
Issue 18 Page 16 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
ZONE MARKING
Zone marking of an area on a forged part
or a grey iron cast part. Within the zone-
marked area, the allowed surface defects
are limited in accordance with the
standard referred to on the relevant
drawing /
Zonmarkering av område på en smidd
artikel eller en gjuten gråjärnsartikel. Inom
det zonmarkerade området är de tillåtna
ytdefekterna begränsade enligt standard
som åberopas på den aktuella ritningen
For cast grey iron parts, the word “zone
marking” shall be indicated. Interpretation
in accordance with STD 330-0001. (See
figure) /
För gjutna gråjärnsartiklar anges ordet
”zone marking”. Tolkning enligt
STD 330-0001. (Se figur)
For cast aluminium parts, the designation
for zone and defect location shall be
indicated in accordance with
STD 330-0013 /
För artiklar i gjutet aluminium anges
beteckningen för zon och defektplacering
enligt STD 330-0013
Established by this
standard /
Fastställd genom denna
standard
Zone marking of cast spheroidal iron parts
and cast steel parts. Indication of defect
classes and defect levels.
STD 330-0002 for spheroidal graphite iron
castings and STD 330-0003 for steel
castings. /
Zonmarkering av gjutna segjärnsartiklar
och gjutstålsartiklar. Angivelse av
defektklasser och defektnivåer.
STD 330-0002 för segjärn och
STD 330-0003 för gjutstål.
STD 330-0002
STD 330-0003
6.4 Requirements on edges 6.4 Krav på kanter
Drawing method
Ritsätt
Explanation
Betydelse
Established by standard
Fastställd i standard
Requirements on edges /
Krav på kanter
STD 102-0008
DEFECT CLASS 1, DEFECT LEVEL 2
DEFECT CLASS 3, DEFECT LEVEL 3
Standard STD 101-0005 Volvo Group
Issue 18 Page 17 (31)
7 Geometrical product specifi-cations (GPS) – Tolerances and surface texture
7 Geometriska produktspecifi-kationer (GPS) – Toleranser och ytstruktur
Within this area, there are several fundamental
standards which are referred to in the standards we
refer to in section 7 of this standard. These
standards thus also apply within the Volvo Group.
Two of these that are of special importance are:
Inom detta område finns flera standarder av grund-
läggande karaktär som man kommer till genom
hänvisningar i de standarder som vi hänvisar till i
avsnitt 7 i denna standard. Dessa gäller då också
inom Volvokoncernen och två av dessa som är
speciellt viktiga är:
ISO 8015:2011 Fundamentals – Concepts, principles and rules / Grunder – Begrepp, principer
och regler
ISO 14253-1:2017 Decision rules for veryfying conformance or non-conformance with specifications /
Regler för hur överensstämmelse eller icke överensstämmelse med specifikationer
bevisas
When statistically evaluating a process, the below
standard applies:
Vid statistisk utvärdering av en process gäller
nedanstående standard:
STD 105-0009 Capability and performance studies. STD 105-0009 Capability and performance studies.
In sections 7.1 – 7.3 below, the most commonly used
indications and symbols are shown. A direct
reference to the standard that explains the meaning
of the indication is also given.
I avsnitt 7.1 – 7.3 nedan visas de vanligaste
skrivsätten och symbolerna som kan användas.
Hänvisning ges också direkt till den standard som
förklarar innebörden av skrivsättet.
These standards apply within the Volvo Group, and it
shall be noted that they can include more ways to
indicate than section 7 in this standard shows.
Dessa standarder gäller inom Volvokoncernen och
kan alltså innehålla fler möjliga skrivsätt än vad som
visas i avsnitt 7 i denna standard.
7.1 Dimensional tolerances 7.1 Dimensionstoleranser
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
ISO tolerance (holes) /
ISO-tolerans (hål)
ISO 286-1:2010
ISO 14405-1:2016
ISO tolerance (shafts) /
ISO-tolerans (axlar)
ISO 286-1:2010
ISO 14405-1:2016
±0,2 ± tolerance for linear sizes /
± tolerans för linjära storleksmått
ISO 14405-1:2016
±0,2 ± tolerance for dimensions other than linear
sizes / ± tolerans för andra mått än
storleksmått
ISO 14405-2:2011
Standard STD 101-0005 Volvo Group
Issue 18 Page 18 (31)
7.2 Geometrical tolerances and datums 7.2 Form- och lägetoleranser och referenser
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Ø0,5 A
Tolerance frame with example of information /
Toleransrektangel med exempel på uppgifter:
Datum / Referens
Tolerance value / Toleransvärde
Toleranced characteristic /
Toleranssatt egenskap
ISO 1101:2017
Toleranced profile characteristic applies all
around the outline /
Toleranssatt profilegenskap gäller runtom hela
konturen
ISO 1101:2017
±1,2°
Tolerance for angular dimension (fraction of
degree in decimals) /
Tolerans för vinkelmått (del av grad i
decimaler)
ISO 14405-2:2011
E
Envelope requirement / Enveloppkrav ISO 14405-1:2016
Specification modifier. Evaluation shall be
made using the least-squares method /
Specifikationsmodifierare. Utvärdering ska
göras med minsta kvadratmetoden
This standard contains many different modi-
fiers (with different two-letters designation)
which give different evaluation rules /
Standarden innehåller många modifierare
(med olika tvåbokstavsbeteckning) som
innebär olika utvärderingsregler
ISO 14405-1:2016
CT Common feature / Gemensamt element ISO 14405-1:2016
ACS Any cross section / Alla tvärsnitt ISO 14405-1:2016
SCS Specific cross section / Ett bestämt tvärsnitt ISO 14405-1:2016
Standard STD 101-0005 Volvo Group
Issue 18 Page 19 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
CZ = Combined Zone
A single tolerance zone that applies to several
separate features /
CZ = gemensamt toleransområde
Ett enskilt toleransområde som gäller för flera
separata element
ISO 1101:2017
P
Projected tolerance zone /
Utflyttat toleransområde
ISO 1101:2017
M
Maximum material requirement /
Max materialkrav
ISO 2692:2014
L
Least material requirement /
Min materialkrav
ISO 2692:2014
Reciprocity requirement / Reciprocitetskrav ISO 2692:2014
F
Free state condition / Fritt tillstånd ISO 10579:2010
Indication of measuring principles /
Angivelse av mätprinciper
Example: measuring principles 2 and 3 /
Exempel: mätprinciper 2 och 3
STD 112-0004
A
Indication of datum / Angivelse av referens ISO 5459:2011
Datum target / Lokal referens
Example: datum target point A1 /
Exempel: lokal referenspunkt A1
ISO 5459:2011
MP 2
MP 3
Standard STD 101-0005 Volvo Group
Issue 18 Page 20 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Datum target / Lokal referens
Example: datum target line A1 /
Exempel: lokal referenslinje A1
ISO 5459:2011
Datum target / Lokal referens
Example: datum target area A1, 14 /
Exempel: lokal referensarea A1, 14
ISO 5459:2011
Datum target / Lokal referens
Example: datum target area A1, 11x16 /
Exempel: lokal referensarea A1, 11x16
ISO 5459:2011
Datum target for coordinate system
(only letters X, Y and Z designating coordinate
direction are used) /
Lokal referens för koordinatsystem
(endast bokstäverna X, Y och Z, som betecknar
koordinatriktning, används)
Example: datum target area X4, 25 /
Exempel: lokal referensarea X4, 25
STD 101-0003
Standard STD 101-0005 Volvo Group
Issue 18 Page 21 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
aY2
Datum target for interface system in coordinate
system (interface systems are identified with a
small letter preceding the coordinate letter) /
Lokal referens för interface-system i koordinat-
system (interface-system identifieras med en
liten bokstav före koordinatbokstav)
Example: datum target point aY2 /
Exempel: lokal referenspunkt aY2
STD 101-0003
7.2.1 Geometrical tolerances for design in coordinate system
7.2.1 Form- och lägetoleranser för konstruktioner i koordinatsystem
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
XYZ
Datum targets and supports for coordinate
systems constitute the datum features
(designs in coordinate system) /
Lokala referenser och stöd för koordinatsystem
utgör referenselement (konstruktioner i
koordinatsystem)
STD 112-0006
B2
B
Requirement on step between parts /
Krav på steg mellan artiklar
STD 112-0006
5±2
GV 1
Requirement on gap variation (GV) /
Krav på spelvariation (GV)
STD 112-0006
Standard STD 101-0005 Volvo Group
Issue 18 Page 22 (31)
7.3 Surface texture 7.3 Ytstruktur
7.3.1 Surface texture profile 7.3.1 Ytstruktur profil
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
A) B) C)
A) Basic graphical symbol for surface
texture / Grundläggande grafisk
symbol för ytstruktur
B) Expanded graphical symbol indicating
removal of material required / Utökad
grafisk symbol som anger att material
ska avverkas
C) Expanded graphical symbol indicating
removal of material not permitted /
Utökad grafisk symbol som anger att
materialavverkning inte är tillåten
STD 120-0004
Complete graphical symbol.
Complementary requirements for surface
texture characteristics are specified in
connection to this symbol /
Komplett grafisk symbol.
Kompletterande krav på ytstrukturens
egenskaper ges i anslutning till denna symbol
STD 120-0004
Standard STD 101-0005 Volvo Group
Issue 18 Page 23 (31)
7.3.2 Surface texture areal 7.3.2 Ytstruktur areal
A) B) C)
A) Basic graphical symbol for surface
texture / Grundläggande grafisk
symbol för ytstruktur
B) Expanded graphical symbol indicating
removal of material required / Utökad
grafisk symbol som anger att material
ska avverkas
C) Expanded graphical symbol indicating
removal of material not permitted /
Utökad grafisk symbol som anger att
materialavverkning inte är tillåten
STD 120-0029
Complete graphical symbol.
Complementary requirements for surface
texture characteristics are specified in
connection to this symbol /
Komplett grafisk symbol.
Kompletterande krav på ytstrukturens
egenskaper ges i anslutning till denna symbol
STD 120-0029
8 Special characteristics 8 Speciella egenskaper
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
[CC] Critical characteristic /
Kritisk egenskap
STD 105-0007
[SC] Significant characteristic /
Signifikant egenskap
STD 105-0007
[1] Criticality 1 /
Allvarlighetsgrad 1
STD 105-0001
[2] Criticality 2 /
Allvarlighetsgrad 2
STD 105-0001
[3] Criticality 3 /
Allvarlighetsgrad 3
STD 105-0001
Standard STD 101-0005 Volvo Group
Issue 18 Page 24 (31)
9 Significant characteristics for regulatory compliance
9 Viktiga egenskaper för uppfyllande av lagar och bestämmelser
Drawing method
Ritsätt
Explanation
Betydelse
Established by standard
Fastställd i standard
[2R] Non-compliance with the requirement for the
characteristic in question is liable to cause high
risk of interference with legal or governmental
emission requirements /
Icke-uppfyllande av kravet för markerad
egenskap förväntas orsaka stor risk för konflikt
med lag- eller myndighetskrav på utsläpp
STD 105-0004
[3R] Non-compliance with the requirement for the
characteristic in question is liable to cause risk
of interference with legal or governmental
emission requirements /
Icke-uppfyllande av kravet för markerad
egenskap förväntas orsaka risk för konflikt med
lag- eller myndighetskrav på utsläpp
STD 105-0004
Product, assembly or single part being subject
to regulations. Note: This indication includes
both the graphical symbol and the letter “R” /
Produkt, komplettartikel eller detalj är föremål
för lag- eller myndighetskrav. OBS! Denna
angivelse innehåller både den grafiska
symbolen och bokstaven ”R”
Renault Trucks
RT 00.10.4007
10 Documentation requirements 10 Dokumentationskrav
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
CR
Requirement for complete documentation /
Krav på fullständig dokumentation
STD 5032,2
RR
Requirement for results records /
Krav på resultatdokumentation
STD 5032,2
R
Standard STD 101-0005 Volvo Group
Issue 18 Page 25 (31)
11 Hardness and case depth 11 Hårdhet och härddjup
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
350 HBW
Designation of Brinell hardness /
Beteckning för Brinellhårdhet
Brinell hardness 350 determined with a
hard metal ball /
Brinellhårdhet 350 bestämd med hård-
metallkula
STD 323-0001
600 HBW 5/ 750/ 20
When needed, the designation is supplemented
with: /
Vid behov kompletteras beteckningen med:
Ball diameter (mm) / Kuldiameter (mm)
Mass (kg) that yields the test force /
Massa (kg) som åstadkommer provkraften
Duration of test force application (s) /
Hålltid (s)
59 HRC
Designation of Rockwell hardness /
Beteckning för Rockwellhårdhet
Rockwell hardness 59, measured on the
Rockwell C-scale /
Rockwellhårdhet 59 bestämd enligt
Rockwellskala C
STD 323-0002
640 HV
Designation of Vickers hardness /
Beteckning för Vickershårdhet
Vickers hardness 640 / Vickershårdhet 640
STD 323-0003
640 HV 30/ 20
When needed, the designation is supplemented
with: /
Vid behov kompletteras beteckningen med:
Mass (kg) that yields the test force /
Massa (kg) som åstadkommer provkraften
Duration of test force application (s) /
Hålltid (s)
Standard STD 101-0005 Volvo Group
Issue 18 Page 26 (31)
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
DC = 1,2 0,3
Designation of case-hardened depth /
Beteckning för sätthärdningsdjup:
Case-hardened depth 1,2 0,3 /
Sätthärdningsdjup 1,2 0,3
STD 322-0002
+ 0,2 DC 650 = 0,4 - 0,1
Requirement for another hardness limit for the
case-hardened depth than 550 HV shall be
indicated as in the example below /
Krav på annan gräns för sätthärdningsdjupet än
550 HV anges enligt nedanstående exempel:
Case-hardened depth 0,4 + 0,2/- 0,1 at
650 HV /
Sätthärdningsdjup 0,4 + 0,2/- 0,1 vid
650 HV
DI = 2 1
Designation of induction-hardened depth /
Beteckning för induktionshärdningsdjup:
Induction-hardened depth 2 1 /
Induktionshärdningsdjup 2 1
STD 322-0001
DI 500 = 2 1
Requirement for another hardness limit for the
induction-hardened depth than 400 HV shall be
indicated as in the example below /
Krav på annan gräns för induktions-
härdningsdjupet än 400 HV anges enligt
nedanstående exempel:
Induction-hardened depth 2 1 vid 500 HV /
Induktionshärdningsdjup 2 1 at 500 HV
DNC = 0,3 MIN
Designation of nitrocarburizing depth /
Beteckning för nitrokarbureringsdjup:
Nitrocarburizing depth 0,3 MIN /
Nitrokarbureringsdjup 0,3 MIN
STD 322-0004
DN = 0,4 0,1
Designation of nitriding depth /
Beteckning för nitrerdjup:
Nitriding depth 0,4 0,1 /
Nitrerdjup 0,4 0,1
STD 322-0003
Standard STD 101-0005 Volvo Group
Issue 18 Page 27 (31)
12 Welding 12 Svetsning
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
1)
2)
Example of symbolic representation of weld
with direct reference to weld requirement STD /
Exempel på svetsbeteckning med direkt
hänvisning till STD med svetskrav
1) Requirement in connection to the weld
symbol / Krav i anslutning till
svetsbeteckningen
2) Requirement as a text note in the
design-engineering documentation /
Krav i form av textnot i konstruktions-
teknisk dokumentation
STD 180-0003
Example of symbolic representation of weld
without direct reference to weld requirement
STD /
Exempel på svetsbeteckning utan direkt
hänvisning till STD med svetskrav
STD 180-0001
Standard STD 101-0005 Volvo Group
Issue 18 Page 28 (31)
13 Screw threads 13 Gängor
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Example of a complete thread designation /
Exempel på en fullständig gängbeteckning
Metric coarse thread / Metrisk grovgänga
STD 5081,15
M8 - 6e Tolerance for external thread (before
coating) /
Tolerans för utvändig gänga (före
ytbehandling)
M8x1 - 6e Example of a designation of an external
metric fine thread (before coating) /
Exempel på beteckning för utvändig metrisk
fingänga (före ytbehandling)
STD 5081,15
M8 - 6H Example of a designation of an internal
metric thread (not coated) /
Exempel på beteckning för invändig metrisk
gänga (ej ytbelagd)
STD 5081,15
M8x1k Special Example of designation of an external taper
metric screw thread /
Exempel på beteckning av utvändig konisk
metrisk gänga
STD 5081,25
Example of a complete thread designation /
Exempel på en fullständig gängbeteckning
PL thread / PL-gänga
STD 5081,45
PL16 - 7h Tolerance for external thread /
Tolerans för utvändig gänga
3/4-14 NPTF
Examples of external Dryseal pipe threads /
Exempel på utvändiga Dryseal-rörgängor:
Taper pipe thread, type NPTF /
Konisk rörgänga, typ NPTF
STD 5081,711
1/4 - 18 PTF-SPL Short Taper pipe thread, type PTF-SPL Short /
Konisk rörgänga, typ PTF-SPL Short
STD 5081,713
3/4-14 NPTF
Examples of internal Dryseal pipe threads /
Exempel på invändiga Dryseal-rörgängor:
Taper pipe thread, type NPTF /
Konisk rörgänga, typ NPTF
STD 5081,721
3/4-14 NPSF Parallel pipe thread, type NPSF /
Cylindrisk rörgänga, typ NPSF
STD 5081,731
Standard STD 101-0005 Volvo Group
Issue 18 Page 29 (31)
14 Moulded parts 14 Formgjorda artiklar
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Parting surface between two mould
components /
Delningsyta mellan två formdelar
STD 101-0008
Parting surface for: / Delningsyta för:
C = Cores / Kärnor
M = Main parting surface /
Huvuddelningsyta
S = Sliders / Backar
STD 101-0008
Maximum permissible mismatch (SMI) for
features intersected by the parting surface /
Maximalt tillåten partförskjutning (SMI) för
element som skärs av delningsyta
STD 101-0008
Maximum permissible deflection caused by
auxiliary mould components, i.e.: /
Maximalt tillåten deformation orsakad av
kompletterande formningskomponenter,
d.v.s.:
G = gate markings / inloppsmärken
R = riser markings / matarmärken
V = vent markings / avluftningsmärken
H = chill markings / nedkylningsmärken
E = ejector markings / utstötarmärken
STD 101-0008
Special ejector markings identifier / Särskild identifiering av utstötarmärke
STD 101-0008
Draft angles / Släppningsvinklar STD 101-0008
Standard STD 101-0005 Volvo Group
Issue 18 Page 30 (31)
15 Other drawing symbols 15 Andra ritningssymboler
Drawing method Ritsätt
Explanation Betydelse
Established by standard Fastställd i standard
Marking of surface not to be painted /
Markering av yta som ej ska lackeras
Established by this
standard /
Fastställd genom denna
standard
Marking of area to be painted with primer
only /
Markering av område som endast ska
lackeras med grundlack
Established by this
standard /
Fastställd genom denna
standard
Marking of first clamping /
Markering av första uppspänning
Established by this
standard /
Fastställd genom denna
standard
Direction towards the drawing plane /
Riktning mot ritningsplanet
Direction from the drawing plane /
Riktning från ritningsplanet
Marking of tightening /
Markering av idragning
Established by this
standard /
Fastställd genom denna
standard
Direction towards the drawing plane /
Riktning mot ritningsplanet
Direction from the drawing plane /
Riktning från ritningsplanet
Part references for constituents in an
assembly /
Artikelreferenser för ingående artiklar i en
komplett
STD 910-0008
Standard STD 101-0005 Volvo Group
Issue 18 Page 31 (31)
16 Information in the drawing sheet blocks
16 Uppgifter i fälten på ritnings- blanketten
For interpretation of information in the title and
revision blocks of the drawing sheet with title block
in accordance with figure 1, STD 910-0001 is
referred to.
För tolkning av uppgifter i ritningsblankettens
huvud- respektive ändringsfält på ritnings-
blanketter med huvudfält enligt figur 1, hänvisas
till STD 910-0001.
The copying, distribution and utilization of this document as well as the communication of its contents to others without expressed authorization is prohibited. Offenders will be held liable for payment of damages. All rights reserved in the event of the grant of a patent, utility model or ornamental design registration.
Document title
Document type
Document No Issue Sheet No
Owner domain:Document prefix
Fig. 1 The form exists in a number of versions with the same layout but with different company names
Blanketten finns i ett antal versioner med samma layout men med olika företagsnamn
17 Reference to this standard 17 Hänvisning till denna standard
For the application of this standard, a reference
shall be given in the design-engineering
documentation in accordance with the below:
Vid tillämpning av denna standard ska hänvisning
göras i konstruktionsteknisk dokumentation enligt
nedan:
SYMBOLS, DESIGNATIONS AND GENERAL DRAWING METHODS STD 101-0005
Recommended