View
219
Download
0
Category
Preview:
Citation preview
8/9/2019 Tablas Weldolets, Thredolets
1/44
RUN PIPE SIZES
Anvilets are manufactured to cover as many run sizes as possible per outlet size. The range of run sizes is based on a maximum gap1/16" between the fitting and the pipe on the largest size of run pipeshown on the fitting.
The following chart shows the range of run pipe sizes per outlet size.
STANDARD, EXTRA STRONG and CLASS 3000 FITTINGS . For outlet NPS 5 to 3 , order !or "#e$%!%$ run #%#e "%&e'
1/8
3/8 x 1/81/2 x 1/81 - 3/4 x 1/8
2 1/2 - 1 1/4 x 1/836-3 x 1/8
1 1/2
1 1/2 x 1 1/22 x 1 1/22 1 /2 x 1 1/23 x 1 1/24 - 3 1/2 x 1 1/2
6 - 5 x 1 1/212 - 8 x 1 1/224 - 14 x 1 1/236 - 26 x 1 1/2
1/4
3/8 x 1/41/2 x 1/41 - 3/4 x 1/4
2 1/2 - 1 1/4 x 1/436 - 3 x 1/4
2
2 x 22 1/2 x 23 x 23 1/2 x 24 x 2
5 x 26 x 210 - 8 x 218 - 12 x 236 - 20 x 2
3/8
1/2 x 3/81 - 3/4 x 3/8
2 1/2 - 1 1/4 x 3 /836 - 3 x 3/8
2 1/2
2 1/2 x 2 1/23 x 2 1/23 1/2 x 2 1/24 x 2 1/25 x 2 1/2
6 x 2 1/28 x 2 1/212 - 10 x 2 1/218 - 14 x 2 1/236 - 20 x 2 1/2
1/21/2 x 1/23/4 x 1/21 x 1/21 1/2 - 1 1/4 x 1/2
2 1/2 - 2 x 1/28 - 3 x 1/236 - 10 x 1/2 3
3 x 33 1/2 x 34 x 35 x 36 x 3
8 x 310 x 314 - 12 x 336 - 24 x 3
3/4
3/4 x 3/41 x 3/41 1/2 - 1 1/4 x 3/42 1/2 - 2 x 3/4
5- 3 x 3/412 - 6 x 3/436 - 14 x 3/4 3 1/2
3 1/2 x 3 1/24 x 3 1/25 x 3 1/26 x 3 1/28 x 3 1/2
10 x 3 1/214 - 12 x 3 1/220 - 16 x 3 1/236 - 24 x 3 1/2
1
1 x 11 1/4 x 11 1/2 x 12 x 12 1/2 x 1
3 1/2 - 3 x 15 - 4 x 110 - 6 x 136 - 12 x 1
4
4 x 45 x 46 x 48 x 4
10 x 414 - 12 x 420 - 16 x 436 - 24 x 4
1 1/4
1 1/4 x 1 1/41 1/2 x 1 1/42 x 1 1/42 1/2 x 1 1/43 1/2 - 3 x 1 1/4
5 - 4 x 1 1/48 - 6 x 1 1/418 - 10 x 1 1/436 - 20 x 1 1/4
8/9/2019 Tablas Weldolets, Thredolets
2/44
CLASS 000 FITTINGS . For outlet NPS ( )*( to )(, order !or "#e$%!%$ run #%#e "%&e'
1/21 - 3/4 x 1/22 - 1 1/4 x 1/26 - 2 1/2 x 1/236 - 8 x 1/2
3/41 x 3/42 1/2 - 1 1/4 x 3/410 - 3 x 3/436 - 12 x 3/4
11 1/2 x 1 1/4 x 12 1/2 - 2 x 110 - 3 x 136 - 12 x 1
11/41 1/2 x 1 1/42 1/2 - 2 x 1 1/43 1/2 - 3 x 1 1/48 - 4 x 1 1/4
20 - 10 x 1 1/436 - 24 x 1 1/4 1 1/2
2 x 1 1/22 1/2 x 1 1/23 1/2 - 3 x 1 1/25 - 4 x 1 1/2
8 - 6 x 1 1/218 - 10 x 1 1/236 - 20 x 1 1/2 2
2 1/2 x 23 x 24 x 25 x 2
6 x 210 - 8 x 212 - 12 x 236 - 24 x 2
SC+' ) 0 XXS' For outlet NPS ( )*( to )(, order !or "#e$%!%$ run #%#e "%&e'
1/21/2 X 1/21 1/4 - 3/4 X 1/236 - 1 1/2 X 1/2 3/4
1 - 3/4 X 3/42 - 1 1/4 X 3/46 - 2 1/2 X 3/436 - 8 X 3/4
11 X 12 1/2 - 1 1/4 X 110 - 3 X 136 - 12 X 1
11/41 1/2 - 1 1/4 X 1 1/42 1/2 - 2 X 1 1/410 - 3 X 1 1/436 - 12 X 1 1/4
1 1/21 1/2 x 1 1/22 1/2 - 2 x 1 1/23 1/2 - 3 x 1 1/28 - 4 x 1 1/2
20 - 10 x 1 1/236 - 24 x 1 1/2 2
2 x 22 1/2 X 23 1/2 - 3 x 25 - 4 x 2
8 - 6 x 218 -10 x 236 - 20 x 2
E-a.#le/ )( 1 - ) )*( Note/If the schedules, or weights, of the bra ch a d ru !i!e are ot thesa"e, the the# "ust be clearl# s!ecified$
E-a.#le/3 %ch$ 80 x 1 1/2 %ch$ 40 &' ( )ilet$
)(1))*(
- is the largest ru !i!e si*e for which the fitti g is a!!licable$- is the s"allest ru !i!e si*e the fitti g is a!!licable$- is the outlet +bra ch si*e$
BUTTWELD ANVILETSull and !educing izes... tandard and #xtra trong
1 $imension %&% is the distance in
inches from the centre of the run pipe to the face of the Anvilet.
' $iameter ( of Anvilet bore is the same as the
inside diameter of the branch pipe of matchingweight or schedule.
8/9/2019 Tablas Weldolets, Thredolets
3/44
The weld or root gap is notincluded in the %&% dimensions
below.
STANDARD 2EIG+T EXTRA STRONG
utlet .o"i al
u i!e (!!rox$ 't$ (!!rox$ 't$
%i*e %i*e ( & ou ds ( & ou ds1/'1/')/*)/*
1/')/* to )6
)/*1 to )6
)/*)/*+/,+/,
-/,1-/161)/161 )/16
1-/161-/161 )/161 )/16
.16
.1+
.'-
.'6
)/*)/*+/,+/,
-/,1-/161)/161 )/16
1-/161-/161 )/161 )/16
.1+
.1
.'6.)
11
1 1/*1 1/*1 1/'1 1/'
11 1/* to)6
1 1/*1 1/' to )6
1 1/'' to )6
1 1/161 1/161 1/*1 1/*
1 -/161 -/16
1 1/)'1 +/161 )/,1 )/*1 -/,
'
1 +/161 +/161 )/*1 )/*
''
.*'.-
.+-
.,'
.,-1.'
1 1/161 1/161 1/*1 1/*
1 -/161 -/16
1 1/)'1 +/161 )/,1 )/*1 -/,
'
1 +/161 +/161 )/*1 )/*
''
.**
.-)
.++
.,,.
1.)
''
' 1/'' 1/'
'' 1/' to )6
' 1/') to )6
1 1/'1 1/'1 -/,1 -/,
' 1/16' /16' +/16
)
' /16' /16
))
1.61.'.*'.+
1 1/'1 1/'1 -/,1 -/,
' 1/16' /16' +/16
)
' /16' /16
))
1.+1.,'.6'.+
))
) 1/') 1/'
)) 1/' to )6
) 1/'* to )6
1 )/*1 )/*
'1 +/,
) 1/16) 11/16) /16
*
) 11/16) 11/16
**
).,*.'-.-.-
1 )/*1 )/*
'1 +/,
) 1/16) 11/16) /16
*
) 11/16) 11/16
**
*.)*.'-.1-.6
STANDARD 2EIG+T EXTRA STRONG
utlet .o"i alu i!e (!!rox$ 't$ (!!rox$ 't$
%i*e %i*e ( & ou ds ( & ou ds**
*- o )6
''
** )/*
* )/** )/*
+.6+.1
''
** )/*
* )/** )/*
+.-+.
--
-6 to )6
' 1/,' 1/*
- 1/160
- 1)/16- /16
,.-1 .)
' 1/16' 1/*
- 1/160
- 1)/16- /16
+.-1 .*
66
6, to )6
' )/,' )/,
6 1/160
6 11/166 11/16
1*1'
) 1/16) 1/16
6 1/160
6 11/166 11/16
1-')
,,
,1 to )6
' )/*' )/*
+ 1-/160
, 11/16, 11/16
',')
) +/,) +/,
+ -/,0
, 11/16, 11/16
)')+
11
11' to )6
) 1/16) 1/16
10
1 1)/161 1)/16
))6
) 1/') 11/16
)/*0
1 +/161 +/16
*6*6
1'1'
1'1* to )6
) )/,) )/,
1'0
1' 1)/161' 1)/16
6--
) 1-/16* 1/16
11 )/*0
1)1' 1/'
6161
1* 1* ) 1/' 1) 1/* 1* 1/16 + * 1/, 1) 1* -/16 +-
8/9/2019 Tablas Weldolets, Thredolets
4/44
1* 16 to )6 ) 1/' 0 1* 1/16 66 ) 1-/16 0 1) 1)/16 + STANDARD 2EIG+T EXTRA STRONG
utlet .o"i alu i!e (!!rox$ 't$ (!!rox$ 't$
%i*e %i*e ( & ou ds ( & ou ds1616
161, to )6
) 11/16) 11/16
1- 1/*0
16 1/1616 1/16
'+-
* +/16* )/16
1-0
16 1/'1- +/,
11-1 '
1,1,
1,' to )6
* 1/16) 1)/16
1+ 1/*0
1, -/,1, 1/16
1'-+
* 11/16* )/,
1+0
1, -/,1+ 1-/16
1)1)
''
''* to )6
* -/,*
1 1/*0
' 1/16'
1+-11,
-* 11/16
10
' 1)/16' 1/16
1,+1-,
*'*
'*'6 to )6
- -/,* /16
') 1/*0
'- 1/,'* )/16
',''
- 1/'- 1/'
')0
'- 1/,'* )/16
)16'
Each outlet size of the reducing Anvilets listed above is supplied in several different ranges or run pipe size. Please refer to the run pipe sizes chart of this catalog.
All dimensions are in inches.
STANDARD WEIGHT: tandard weight buttweld Anvilets are usedwith all sizes of tandard pipe or ch. * pipe up to and including 1 .
These Anvilets may be used in con2unction with ch. * and 3lass 'fittings.
ch. * buttweld Anvilets of outlet size '* and over are available uponre4uest.
EXTRA STRONG: #xtra strong buttweld Anvilets are used with allsizes of 5 pipe and are used with ch. , pipe up to and including size
,. These Anvilets may be used in con2unction with ch. , and class) fittings.
ch. , buttweld Anvilets of outlet size '* and over are available uponre4uest.
BUTTWELD ANVILETSull and !educing izes... chedule 16 and $ouble #xtra trong
8/9/2019 Tablas Weldolets, Thredolets
5/44
1 $imension %&% is the distance in inches from thecentre of the run pipe to the face of the Anvilet. Theweld or root gap is not included in the %&% dimensions
below.SCHEDULE 160 and DOUBLE EXTRA STRONG
Outlet
S !e A C
A""#$%. Wt.
&$und'1/')/*
1 1/,1 1/*
/16)/*
.'-
.+11
1 1/*1 1/'
1 1/'1 )/*
'
11 -/161 1/'
.,)1.'-1.+-
'' 1/'
' )/16' +/16
1 11/16' 1/,
'.1)).),
) ' +/, ' +/, 6.)'* ) -/16 ) +/, 1 .-
- ) 11/16 * 1)/16 1*.'-6 * 1/, - )/* ' .-The reducing Anvilets listed above for outlet sizes 1/2 to 2 are suppliedin several different ranges of run pipe size for each outlet. Please referto run pipe sizes chart of this catalog.
Schedule 160 and ouble E!tra Strong butt"eld Anvilets #a$ be used incon%unction "ith &lass 6000 fittings.
(LAT ANVILETS3lass ) Threaded utweld 7 oc8et 9eld
8/9/2019 Tablas Weldolets, Thredolets
6/44
S !e A A""#$%. Wt.&$und'1/*)/,
1/')/*
11/161)/16
11 1/16
.11.'
.)
.*1
1 1/*1 1/'
1 /)'1 11/)'
1 )/,
.+
.1.'
'' 1/'
1 1/'1 )/*
1.,'.+
) ' ).) 'lat Anvilets are designed to facilitate "elding to a flat surface for theinstallation of branch pipes or fittings.
Cla'' 6000 flat Anvilets are available on application.
SOC)ET WELD ANVILETS
ull and !educing izes ... 3lass ) and 6
Cla'' *000 REDUCING and (ULL SI+ES
OutletS !e
N$, nalRun & "e
S !e A B CD1
-.0*
E.01
/.00 (
A""#$%.Wt.
&$und'1/'1/')/*)/*
1/')/* to )6
)/*1 to )6
11
1 1/161 1/16
-/,1-/161)/161 )/16
1-/161-/161 )/161 )/16
.6''
.6''
.,'*
.,'*
.,--
.,--1. 6-1. 6-
1 1/*1 1/*
1 +/161 +/16
.'.)-.'+.*
8/9/2019 Tablas Weldolets, Thredolets
7/44
11
1 1/*1 1/*1 1/'1 1/'
11 1/* to )6
1 1/*1 1/' to )6
1 1/'' to )6
1 -/161 -/161 -/161 -/161 )/,1 )/,
1 1/161 +/161 )/,1 )/*1 -/,
'
1 +/161 +/161 )/*1 )/*
''
1. *1. *1.),1.),1.611.61
1.))1.))1.6+-1.6+-1. 1-1. 1-
1 1)/161 1)/16' )/16' )/16' +/16' +/16
.6
.,
.,1.11.'1.-
''' 1/'' 1/'
'' 1/' to )6' 1/'
) to )6
1 1/'1 1/'1 1)/161 1)/16
' 1/16' /16' 1/'
)
' /16' /16))
'. 6+'. 6+'.*6'.*6
'.* 6'.* 6'. 6'. 6
' 1-/16' 1-/16) +/16) +/16
1.,'.'.-).
OutletS !e
N$, nalRun & "e
S !e A B CD1
-.0*
E.01
/.00 (
A""#$%.Wt.
&$und'))
) 1/'
) 1/'
)) 1/' to )6
) 1/'
* to )6
''
' 1/,
' 1/,
) 1/16) 11/16) /16
*
) 11/16) 11/16
*
*
). 6,). 6,).-*,
).-*,
).-)-).-)-*. *
*. *
* 1/,* 1/,* )/*
* )/*
).,*.'*.)
*.)**
*- to )6
' 1/*' 1/*
* 1/16* )/*
* )/** )/*
*. '6*. '6
*.-*-*.-*-
- 1/,- 1/,
+.',.
Cla'' 6000 REDUCING SI+ES : ull sizes not available;
OutletS !e
N$, nalRun & "e
S !e A CD
-.0*
E.01
/.00 (A""#$%. Wt.
&$und'1/')/*
)/* to )61 to )6
11 1/16
)/*1
.*6*
.61'.,--
1. 6-1 /16
1 '-/)'.-,.
11 1/*1 1/'
1 1/1* to )61 1/' to )6' to )6
1 -/161 -/161 )/,
1 -/161 1/'1 1-/16
.,1-1.161.)),
1.))1.6+-1. 1-
' 1/*' /16)
1.,'.6).
' ' 1/' to )6 1 1/' ' )/* 1.6,+ '.* 6 ) -/, -., Each outlet size of the reducing Anvilets listed above is supplied in several different ranges of run pipe size. Please refer to the run pipe sizes chart in this catalog.
Cla'' *000 soc8et weld Anvilets may be used with tandard and 5 pipe.Cla'' 6000 soc8et weld Anvilets may be used with ch. 16 and 55 pipe.
N$te: 1 Tolerance on sizes ' 1/' and larger is
8/9/2019 Tablas Weldolets, Thredolets
8/44
ull and !educing izes ... 3lass ) and 6
All dimensions are in inches.Cla'' *000 REDUCING and (ULL SI+ES
OutletS !e
N$, nalRun & "e
S !e A B C (
A""#$%.Wt.
&$und'1/'1/')/*)/*
1/')/* to )6
)/*1 to )6
11
1 1/161 1/16
-/,1-/161)/161 )/16
1-/161-/161 )/161 )/16
1 1/*1 1/*
1 +/161 +/16
.'
.).)-.*'
11
1 1/*1 1/*1 1/'1 1/'
11 1/* to )6
1 1/*1 1/' to )6
1 1/'' to )6
1 -/161 -/161 -/161 -/161 )/,1 )/,
1 1/161 +/161 )/,1 )/*1 -/,
'
1 +/161 +/161 )/*1 )/*
''
1 1)/161 1)/16' )/16' )/16' +/16' +/16
.6
.,.,-1.'1.)1.6
''
' 1/'' 1/'
'' 1/' to )6
' 1/') to )6
1 1/'1 1/'
1 1)/161 1)/16
' 1/16' /16' 1/'
)
' /16' /16
))
' 1-/16' 1-/16) +/16) +/16
1.+'.''.-).
OutletS !e
N$, nalRun & "e
S !e A B C (
A""#$%.Wt.
&$und'))
) 1/'
)) 1/' to )6
) 1/'
''
' 1/,
) 1/16) 11/16) /16
) 11/16) 11/16
*
* 1/,* 1/,* -/,
*.)*.**.-
8/9/2019 Tablas Weldolets, Thredolets
9/44
) 1/' * to )6 ' 1/, * * * -/, -.6*-
*- to )6
' 1/*' 1/*
* 1/16* )/*
* )/** )/*
- 1/,- 1/,
+.),.)
Cla'' 6000 REDUCING SI+ES : ull sizes not available;
OutletS !e
N$, nal
Run & "eS !e A B C ( A""#$%. Wt.&$und'1/')/*
)/* to )61 to )6
1 1/*1 +/16
)/*1
)/*1
1 /161 1)/16
.6
.1
1 1/*1 1/'
1 1/1* to )61 1/' to )6
' to )6
1 /161 -/,
1 11/16
1 -/161 1/'
1 1-/16
1 -/161 1/'
1 1-/16
' 1/*' /16
)
'.).).'
' ' 1/' to )6 ' 1/16 ' )/* ' )/* ) -/, 6. Each outlet size of the reducing Anviletslisted above is supplied in several different ranges of run pipe size.
Please refer to the run pipe sizeschart in this catalog.
Cla'' 6000 threaded Anvilets are manufactured only in the sizes shown.Cla'' *000 threaded Anvilets may be used with tandard and 5 pipe.Cla'' 6000 threaded Anvilets may be used with ch. 16 and 55 pipe.
ELBOW ANVILETS3lass ) and 6 uttweld Threaded and oc8et 9eld
8/9/2019 Tablas Weldolets, Thredolets
10/44
CLASS *000 THREADED and SOC)ET WELD STANDARD and XS BUTTWELDOutlet S !e N$, nal El $2 S !e C H A""#$%. Wt. &$und'
1/*)/,1/')/*
)601 1/*)601 1/*)601 1/*)601 1/*
1 1/'1 1/'1 1/'
1 ')/)'
1 1 /)'1 1 /)'1 1 /)'
1 +/,
.-
.-.6-.+-
11 1/*1 1/'
)60')60')60'
' 1/,1 '1/)'
)
' )/16' )/,' -/,
1.1-1.'.6-
' )60) * 1/, ) )/16 -.'-STANDARD nad XS BUTTWELD3 ONL4
' 1/' As pecified * )/16 ) 1/* -.-) As pecified * 1-/16 ) 1)/16 6.'-* As pecified 6 +/16 * 1/' 11.+-6 As pecified 6 )/16 ',.
CLASS 6000 THREADED and SOC)ET WELD SCH. 160 and XXS BUTTWELDOutlet S !e N$, nal El $2 S !e C H A""#$%. Wt. &$und'
1/*)/,1/')/*
)601 1/*)601 1/*)601 1/*
)60'
1 )/,1 )/,
1 ')/)'' 1/,
1 1 /)'1 1 /)'
1 +/,' )/16
.+-
.+-
.,-1.'-
11 1/*1 1/'
)60')60')60)
' '1/)')
* 1/,
' )/,' -/,
) )/16
'.').6.'
#lbow Anvilets are welded = long radius elbows as branchconnections for pipes and fittings. They are also used as pipehanger or support bosses.
All $imensions are in inches.
LATERAL ANVILETS
8/9/2019 Tablas Weldolets, Thredolets
11/44
3lass ) and 6 uttweld Threaded and oc8et 9eld
>ateral Anvilets provide a strong readily attached *-= lateral outlet connection
All dimensions are in inchesCLASS *000 THREADED and SOC)ET WELD STANDARD and XS BUTTWELD
Outlet S !e N$, nalRun & "e S !e
H B C A""#$%. Wt. &$und'
1/* ' 1/'01 1/* / 1'0) 1 1/' ' 1/* 1 +/16 .-)/, ' 1/'01 1/* / 1'0) 1 1/' ' 1/* 1 +/16 .-1/' ' 1/'01 1/* / 1'0) 1 1/' ' 1/* 1 +/16 .6-)/* 1 1/'01 1/* / -0' / 1'06 1 1)/16 ' )/* 1 ')/)' .+-1 ' 1/'0' / -0) / 1'06 ' 1/, ) 1/* ' 1/, 1.1-
1 1/* ' 1/'0' / -0) / 1'06 ' /16 ) 1)/16 ' '1/)' 1.1 1/' ' 1/'0' / -0) / 1'06 ' )/* * 1/* ) '.6-
' -0* / ,06 / 1'01 ) )/, - )/, * 1/, -.'-
CLASS 6000 THREADED and SOC)ET WELD SCH. 160 and XXS BUTTWELD
8/9/2019 Tablas Weldolets, Thredolets
12/44
Outlet S !eN$, nal
Run & "e S !e H B C A""#$%. Wt. &$und'
1/* ' 1/'01 1/* / 1'0) 1 1/' ' 1/* 1 )/, .+-)/, ' 1/'01 1/* / 1'0) 1 1/' ' 1/* 1 )/, .+-1/' 1 1/'01 1/* / -0' / 1'06 1 1)/16 ' )/* 1 ')/)' .,-)/* ' 1/'0' / -0) / 1'06 ' 1/, ) 1/* ' 1/, 1.'-
' 1/'0' / -0) / 1'06 ' /16 ) 1)/16 ' '1/)' '.'
1 1/* ' 1/'0' / -0) / 1'06 ' )/* * 1/* ) '.1 1/' -0* / ,06 / 1'01 ) )/, - )/, * 1/, 6.1-
CLASS 5000THREADED (ITTINGS
NO INAL &I&ESI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
90 ELBOWSA . +? . +? . + 1.1' 1.)1 1.- 1.+- '. '.), ). ).', *.1
& 1. ? 1. ? 1. 1.)1 1.- 1.,1 '.1 '.** '. + ).6' *.)1 -.+-
App. 9t./1 pcs. )1 )1 )1 - 6 11) 1-, ' )- 6- 11 ''+-
NO INAL &I&E
SI+E1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
8/9/2019 Tablas Weldolets, Thredolets
13/44
8/9/2019 Tablas Weldolets, Thredolets
14/44
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 890 ELBOWS
A . +? . + 1.1' 1.)1 1.- 1.+- '. '.), '.- ).'- ).+- *.-
& 1. ? 1. 1.)1 1.- 1.,1 '.1 '.** '. + ).)1 *. *.+- 6.
App. 9t./1 pcs. ), ), 6) ,, 1), ''- '6 * -1 1 - 1*** ) ),NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 88; ELBOWS
3 .+-? .+- .,, 1. 1.1' 1.)1 1.), 1.6 1.+' '. 6 '.- ).1'
& 1. ? 1. 1.)1 1.- 1.,1 '.1 '.** '. + ).)1 *. *.+- 6.
App. 9t./1 pcs. '- '- -' 6, 11 1,, '1) * ** +), 11+, 1 6
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8TEES
A . +? . + 1.1' 1.)1 1.- 1.+- '. '.), '.- ).'- ).+- *.-
& 1. ? 1. 1.)1 1.- 1.,1 '.1 '.** '. + ).)1 *. *.+- 6.
8/9/2019 Tablas Weldolets, Thredolets
15/44
App. 9t./1 pcs. ), ), ,1 11 1,, )1 )- 6* 6,6 1)1) ' ), ) -
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
CROSSESA . +? . + 1.1' 1.)1 1.- 1.+- '. '.), '.- ).'- ).+- *.-
& 1. ? 1. 1.)1 1.- 1.,1 '.1 '.** '. + ).)1 *. *.+- 6.
App. 9t./1 pcs. ), ), 1 1- '- )-6 *1) 6- ,1) 16+- 1 +- )'
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
STREET ELBOWSA . +? . + 1.1' 1.)1 1.- 1.+- '. '.), '.- ).'- ).+- *.-
1.'- 1.'- 1.- 1.6 1. * '.)1 '.6 '.,1 ).), 0 0 0
& 1. 1. 1.)1 1.- 1.,1 '.1 '.** '. + ).)1 *. *.+- 6.
App. 9t./1 pcs. '- '- ), -- ,, 1** '- *'- -1 0 0 0
?>arger than A @# 16.11 dimension.
CLASS 6000THREADED (ITTINGS
8/9/2019 Tablas Weldolets, Thredolets
16/44
NO INAL &I&ESI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
90 ELBOWSA . + 1.1' 1.)1 1.- 1.+- '. '.), '.- ).'- ).+- *.1 *.-
& 1. 1.)1 1.- 1.,1 '.1 '.** '. + ).)1 *. *.+- -.+- 6.
App. 9t./1 pcs. '- 6) 1 6 16) '- )'- 6- +'- 1)'- ' ,, )*-6 0NO INAL &I&ESI+E
1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
8; ELBOWS3 .+- .,, 1. 1.1' 1.)1 1.), 1.6 1.+' '. 6 '.- ).1' ).1'
& 1. 1.)1 1.- 1.,1 '.1 '.** '. + ).)1 *. *.+- -.+- 6.
App. 9t./1 pcs. '- - ,, 1** '1 '6 *6 -+- - 1- ) -6 0
NO INAL &I&ESI+E
1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
TEESA . + 1.1' 1.)1 1.- 1.+- '. '.), '.- ).'- ).+- *.1 *.-
8/9/2019 Tablas Weldolets, Thredolets
17/44
& 1. 1.)1 1.- 1.,1 '.1 '.** '. + ).)1 *. *.+- -.+- 6.
App. 9t./1 pcs. - 1 1), '1) )6) *6) +6) 6) 1,,, ', 6 *-6) 0
NO INAL &I&ESI+E
1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
CROSSESA . + 1.1' 1.)1 1.- 1.+- '. '.), '.- ).'- ).+- *.1 0
& 1. 1.)1 1.- 1.,1 '.1 '.** '. + ).)1 *. *.+- -.+- 0
App. 9t./1 pcs. -6 11 1- '+- *)1 -6) 1 +- 11- ''1 '+- -* 0
NO INAL &I&ESI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
STREET ELBOWSA 0 1. 1.1' 1.), 1.+- '. '.1' '.- 0 0 0 0
0 1.- 1.6) 1.,, '.'- '.6' '.,1 ).)1 0 0 0 0
& 0 1.'- 1.- 1.+- '. '.** '.+- ).)1 0 0 0 0
App. 9t./1 pcs. 0 )+ *- 1 16' '- )6, 6** 0 0 0 0
?>arger than A @# 16.11 dimension.
CLASS *000SOC)ET WELDING (ITTINGS
8/9/2019 Tablas Weldolets, Thredolets
18/44
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
CO ONDI ENSIONS
: oc8et $ia.; .*' / .---/ .6 / .,--/ 1. 6-/ 1.)) / 1.6+-/ 1. 1-/ '.* 6/ '. 6/ ).-)-/ *.-*-/.** .-+- .+1 .,+- 1. ,- 1.)- 1.6 - 1. )- '.*'6 '. )1 ).-6 *.-+
3 :@in.; .1) .1) .1* .16 .1+ .' .'1 .'' .'* .) .)) .)+
$ : ore $ia.; .') / .))*/ .*6)/ .- '/ .+ */ 1. 1 / 1.)- / 1.-, / '. )+/ '.* / ). ,/ ). 66/.' .) * .-') .6-' .,-* 1. + 1.*1 1.6* '. + '.-' ).1', *. ,6
B :@in. oc8et $epth; .), .), .), .), .- .- .- .- .6' .6' .6' .+-
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
90 ELBOWSA
:Cominal;.** .** .-) .6' .+- .,, 1. 6 1.'- 1.- 1.6' '.'- '.6'
App. 9t./1 pcs 1) 1) '- - 6 1 6 16) '1) ' 6), 1 ,, ')6
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
8; ELBOWSA
:Cominal; .)1 .)1 .)1 .** .- .-6 .6 .,1 1. 1.1' 1.'- 1.6'
App. 9t./1 pcs
1) 1) 1 ), - ,, 1'- 16) '6 6+- 1 - 1,1
8/9/2019 Tablas Weldolets, Thredolets
19/44
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
TEESA .** .** .-) .6' .+- .,, 1. 6 1.'- 1.- 1.6' '.'- '.6'
App. 9t./1 pcs '- '- )* 6 ,, 1** '1) '6) *** ,,, 1)6 ',**
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8CROSSES
A .** .** .-) .6' .+- .,, 1. 6 1.'- 1.- 1.6' '.'- '.6'
App. 9t./1 pcs '- )1 )1 ,1 11) 1-6 '** )'- -- 1-,1 ' 1 )1-
To prevent possible crac8ing of the fillet welds if the pipe isseated against the bottom of the soc8et prior to welding it isrecomended that the pipe be withdrawn approximately 1/16 in.away from the bottom of the soc8et before starting the weld.
CLASS 6000SOC)ET WELDING (ITTINGS
8/9/2019 Tablas Weldolets, Thredolets
20/44
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8CO ONDI ENSIONS
: oc8et $ia.; .*' / .---/ .6 / .,--/ 1. 6-/ 1.)) / 1.6+-/ 1. 1-/ '.* 6/ '. 6/ ).-)-/ *.-*-/.** .-+- .+1 .,+- 1. ,- 1.)- 1.6 - 1. )- '.*'6 '. )1 ).-6 *.-+
3 :@in.; .1* .16 .1+ .' .'* .'+ .'+ .)1 .)+ .*1 .*, .-,
$ : ore $ia.; .1'6/ .'' / .)' / .*)*/ .-,'/ .+,-/ 1.1) / 1.) ,/ 1.6-+/ '. 6-/ '.-6*/ ).)+,/.1, .', .), .* * .6*' .,*- 1.1 1.)6, 1.+1+ '.1,- '.6,* ).* ,
B :@in. oc8et $epth; .), .), .), .), .- .- .- .- .6' .6' .6' .+-
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
90 ELBOWSA
:Cominal;.** .-) .6' .+- .,, 1. 6 1.'- 1.- 1.6' '.'- '.- '.6'
App. 9t./1 pcs 0 0 0 ,, 1** '- )'- -)1 6), 1' 1 ), )6),
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
8; ELBOWSA
:Cominal; .)1 .)1 .** .- .-6 .6 .,1 1. 1.1' 1.'- 1.), 1.-,
App. 9t./1 pcs
0 0 0 6 1)1 ' '6) *+- -,, +1) 1')1 '+
8/9/2019 Tablas Weldolets, Thredolets
21/44
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
TEESA 0 0 0 .+- .,, 1. 6 1.'- 1.- 1.6' '.'- '.- '.6'
App. 9t./1 pcs 0 0 0 1 6 ' 6 )), *)1 +,1 ,6 166) '),1 *-)'
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8CROSSES
A 0 0 0 .+- .,, 1. 6 1.'- 1.- 1.6' '.'- '.- '.6'
App. 9t./1 pcs 0 0 0 1'- '- * -1) - 1 ,, ' - *1-
To prevent possible crac8ing of the fillet welds if the pipe isseated against the bottom of the soc8et prior to welding it isrecomended that the pipe be withdrawn approximately 1/16 in.away from the bottom of the soc8et before starting the weld.
HIGH &RESSURE &LUGS AND BUSHINGS
8/9/2019 Tablas Weldolets, Thredolets
22/44
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8
&LUGS All dimensions except # and are minimumsS
8/9/2019 Tablas Weldolets, Thredolets
23/44
HEX HEAD
A 0 .** .- .-6 .6' .+- .,1 .,1 .,, 1. 6 1.1' 1.'-0 .6' .6 .,, 1. 6 1.), 1.+- '. '.- ). ).- *.6'0 .1' .16 .1 .'' .'- .', .)1 .)* .), .*1 .-
>owest !eduction 0 1/, 1/, 1/, 1/, 1/, 1/, 1/* 1/* 1/' 1/' 1 1/'App. 9t./1 pcs 0 ' - 6 1) 1 ) 6, 16) '), )- ,)1
NO INAL &I&E SI+E 1 7 1 8 * 7 1 5 * 8 1 1 1 8 1 1 5 5 5 1 5 * 8(LUSH
A 0 .** .- .-6 .6' .+- .,1 .,1 .,, 1. 6 1.1' 1.'->owest !eduction 0 1/, 1/, 1/, 1/, 1/, 1/, 1/* 1/* )/* 1 1 1/'
App. 9t./1 pcs 0 ' - 6 1) 1) 1) 1 ), 6) 1 '
CoteD Elugs and bushings are not identified by pressure class. Theymay be used for ratings up to pressure class 6 :per A @# 16.11;
SOC)ET WELDING REDUCER INSERTS
!educer inserts comply with @ tandard E0+ .They enable standard soc8et welding fittings to beused for ma8ing any combination of pipe linereductions 4uic8ly and economically.
oc8et welding reducer inserts serve the same purpose as threaded reducing bushingswith threaded fittings.
TFE# 1 !#$G3#! HC #!T TFE# ' !#$G3#! HC #!T
CI@. I3(#T &AC( 3lass ) 0 or Gse 9ith 3lass 6 0 or Gse 9ith
8/9/2019 Tablas Weldolets, Thredolets
24/44
8/9/2019 Tablas Weldolets, Thredolets
25/44
x 1 1/* 1.6, .- '.,, ' 1.** 1.), .') 0 '.1' 0 0 0 0 0 0x 1 1.)* .- '.,, ' 1.- 1. - .''6 0 '.1' 0 0 0 0 0 0x )/* 1. + .- '.,, ' 1.-6 .,' .1 ) 0 '.1' 0 0 0 0 0 0
) x ' 1/' '. 1 .6' ).- 1 1.- '.*+ .)*- 1.'- 0 0 0 0 0 0 0x ' '.*1 .6' ).- ' 1. '. + .'+) 0 1.,+ 0 0 0 0 0 0x 1 1/' 1. ' .- ).- ' 1.1' 1.61 .'- 0 1.,+ 0 0 0 0 0 0x 1 1/* 1.6, .- ).- ' 1.1 1.), .') 0 1.,+ 0 0 0 0 0 0
x 1 1.)* .- ).- ' 1.'- 1. - .''* 0 1.,+ 0 0 0 0 0 0
To mimimize the posibility of crac8ing of the fillet welds. it is recomended that the shan8 portion of the reducer be withdrawn approximately 1/16 away from contact with the bottom ofthe soc8et before starting the weld. >i8ewise the pipe is to be 8ept away from contacting the
bottom of the reducer soc8et before welding.
THREADED UNIONS
8/9/2019 Tablas Weldolets, Thredolets
26/44
• teel0to0steel seats• A. .T.@. teel specification A1 -.• @anufactured to @ 0 E,) specifications.
:3lass 6 by method of @ 0 E,);.• Taper threaded to A @# standard 1.' .1• 3lass ) brass0to0steel seats also available. !efer to price list.
@ale/female unions and stainless steel orifice plates available on re4uest
N$, nal & "e S !e D ,en' $n'A""#$%. Wt.l '. 100 "='.Cla'' *000 Cla'' 6000 L A , n.
1/* 0 1. ) 1.- .+- )-
)/, 1/* '. , 1.6 . -
1/' )/, '.1, 1.,1 1. 66
)/* 1/' '.- '.1 1.)' 1 ,
1 )/* '.6 '.-6 1.6) 16-
1 1/* 1 '., ). 6 1. ')-
1 1/' 1 1/* ). 1 ).*' '.'- )'
' 1 1/' ).) *. '.+6 *6
' 1/' ' *. ) *.,, ).)6 ,'-
8/9/2019 Tablas Weldolets, Thredolets
27/44
) 0 *.' -.+- *. ) 116
SOC)ET WELDING UNIONS
8/9/2019 Tablas Weldolets, Thredolets
28/44
• teel0to0steel seats• A. .T.@. teel specification A1 -.• @anufactured to @ 0 E,) specifications.
:3lass 6 by method of @ 0 E,);.•
Taper threaded to A @# standard 1.' .1• 3lass ) brass0to0steel seats alse available. !efer to pricelist.
tainless steel orifice plates available on re4uest
N$, nal & "e S !e D ,en' $n'A""#$%. Wt.l '. 100 "='.
Cla'' *000 Cla'' 6000 L A , n.B
Cla'' *000B
Cla'' 6000) , n.
1/* 0 1. ) 1.- .,6 .-6 .*' .), )*)/, 1/* '. , 1.6 1. ' .6 .-6 .), *1/' )/, '.1, 1.,1 1.') .,6 .6 .), 6))/* 1/' '.- '.1 1.*6 1. + .,6 .- 1 61 )/* '.6 '.-6 1.+ 1.)) 1. + .- 16
1 1/* 1 '., ). 6 '.16 1.6, 1.)) .- ')-1 1/' 1 1/* ). 1 ).*' '.*' 1. ' 1.6, .- )1'
' 1 1/' ).) *. '. 6 '.*1 1. ' .6' *-'' 1/' ' *. ) *.,, ).61 '. 1 '.*1 .6' ,'
) 0 *.' -.+- *.) ).-* 0 .6' 116
8/9/2019 Tablas Weldolets, Thredolets
29/44
STANDARDERCHANT COU&LINGS
&alf couplings are chamfered on one end withthe other end s4uare.
@anufactured in accordance with A T@ specification A,6-.
@erchant couplings in CE 1/, through ' are normallysupplied straight tapped. CE ' 1/' and larger aretaper tapped.
Taper tapped standard merchant couplings in CE 1/,through ' are available upon re4uest.
AEH line pipe couplings are used in all sizes over CE 6.
3ouplings from CE 1/, through ' are dipped in rust preventative.
3ouplings CE ' 1/' and larger are phosphated.
alvanized full couplings are also available.
All dimensions are in inches.
N$, nal& "e S !e
Out' de D a.>C$u"l n?@
Len?tT #ead'"e# n=
A""#$% Wt. L '."e# 100 & e=e'
Ca#t$n
8/9/2019 Tablas Weldolets, Thredolets
30/44
1/')/*
1. 6)1.)1)
1 /161 -/,
''/)')/*
1*1*
1+ 1/''6
,1'
1-
11
11 1/*1 1/'
1.-+61.'.'
'' 1/16' 1/16
1-/16)1/)')1/)'
11 1/'11 1/'11 1/'
*'-6+
'') 1/')1 1/'
)'-'-
+-1+-
'' 1/'
'.+-).'-
' 1/,) 1/,
11 1/'
11 1/',
1 )'16
*, 1/'1 ) 1/'
'0
-0
)) 1/'
*.*.6'-
) 1/*) )/,
1 /161 -/,
,,
)*+-1
16+'-*
00
00
* -. ) 1/' 1 11/16 , *,, ')- 0 0- 6.' 6 ) )/* 1 )/* , ,+- *' 0 06 +.) * 1 +/, , 11,, -- 0 0
EXTRA STRONGCOU&LINGS
&alf couplings are chamfered on oneend with the other end s4uare.
@anufactured in accordance with A T@ specification A,6-.
All sizes are taper tapped.
Con recessed couplings will be supplied on CE - andunder unless otherwise specified
3ouplings CE 6 and above will be supplied recessed only.
3ouplings from CE 1/, through 1 1/' are dipped in rust
preventative.
8/9/2019 Tablas Weldolets, Thredolets
31/44
3ouplings CE ' and larger are phosphated.
alvanized full couplings are also available.
All dimensions are in inches.
A""#$% Wt. L '. &e# 100 & e=e'
N$, nal& "e S !e Out' de D a.>C$u"l n?@ Len?t Re=e''ed N$n/Re=e''ed Ca#t$n
8/9/2019 Tablas Weldolets, Thredolets
32/44
These couplings are manufactured in accordance with American Eetroleum Hnstitute
pecification ->. All sizes are taper tapped )/*"per foot on diameter.
>ine pipe couplings in CE 1/, 0 1 1/' are dipped in rust preventative.3ouplings in CE ' and larger are phosphated.
All dimensions are in inches.
N$, nal& "e S !e
Out' de D a.>C$u"l n?@ Len?t
A""#$%. Wt. L '."e# 100 & e=e'
Ca#t$n
8/9/2019 Tablas Weldolets, Thredolets
33/44
8/9/2019 Tablas Weldolets, Thredolets
34/44
& "e S !e >C$u"l n?@ "e# 100 & e=e'1/*)/,1/')/*
.+1
.,+-1. 6)1.)1)
1 -/,1 -/,' 1/,' 1/,
1*'-)6
11 1/*1 1/'
1.-+6'. -*'.'
' -/,' )/*' )/*
+*1 ,
-'
' 1/''.,+-).)+-
' +/,* 1/,
' 1)-)
) *. * 1/* *61
&LUGS3 BUSHINGS AND HEX CA&SERCHANT STEEL
SOLID Sbs. per
1 Eieces3arton3ontentsCominal
Eipe ize1/,1/*)/,1/'
)/*IverallElug
>ength:@inimum;
.6'-
.6,+
.,1'
. )+1. 6'
/)')/,
+/16/16
-/,
'+1,1,1*1*
'''
11,
1111-
HAXAGON BUSHINGS
CominalEipe ize
Iverall>ength
9idthAcross
lats
Approx.9eight>bs. per
1 Eieces
3arton3ontents
1/* 5 1/, .6'- .6'- ' 1)/, 5 1/*)/, 5 1/,
.+-
.+-.6,+.6,+
*-
11
1/' 5 )/,1/' 5 1/*1/' 5 1/,
.,+-
.,+-
.,+-
.,+-
.,+-
.,+-
6
1
111
)/* 5 1/')/* 5 )/,)/* 5 1/*)/* 5 1/,
1.1.1.1.
1. 6'1. 6'1. 6'1. 6'
111-1,'
1111
1 5 )/*1 5 1/'1 5 )/,
1. 6'1. 6'1. 6'
1.*)+1.*)+1.*)+
1,'+)'
---
8/9/2019 Tablas Weldolets, Thredolets
35/44
9idthAcross
lats:Cominal;
1 1.1'- 1)/16 11 1/' )- '-
1 5 1/*1 5 1/,
1. 6'1. 6'
1.*)+1.*)+
)-*'
--
SOLID HEXAGON HEAD &LUGS
CominalEipe ize
IverallElug
>ength:@inimum;
9idthAcross
lats:Cominal;
Threads per Hnch
Approx.9eight>bs. per
1 Eieces
3arton3ontents
1/,1/*)/,1/')/*
.,1'
.,+-1.1. 6'1.)1'
+/16-/,
11/16+/,
1 1/16
'+1,1,1*1*
)6
11+)'
1111-
All sizes Taper Tapped 0 )/*" per foot on diameter HCH & I! 3IATHC D lac8 0 $ipped in rust resistantalanized 0 Jinc plated inside and out. or sizes 1 1/*" and larger see our current orged teel 3atalog Eage.
COUNTERSUN) &LUGS >He% and S ua#e S$= et@
CominalEipe
ize
Thread>ength:@in.;
Threadize of oc8et
:@in.;
@etalThic8ness
ottom3ountersin8
:@in..;
Threads per inch
Approx.9eight>bs. per 1 Ecs.
3arton3ontents
4uare &ex
1/,1/*
)/,1/')/*
.)1
.**
.*,.-6
.6)
?1/*
-/16)/,1/'
)/161/*
-/16)/,/16
.
.
.1).16
.1,
'+1,
1,1*1*
11
*611
11
11-
11 1/*1 1/'
.+-
.,
.,)
1/')/*)/*
-/,)/*1
.'
.'-
.'-
11 1/'11 1/'11 1/'
'1)*-'
+--'-
' .,, +/, 1 .'6 11 1/' ,- '? 1/, size not available 4uare oc8et. All sizes Taper Tapped 0 )/* per foot on diameter.
HCH & I! 3IATHC lac8 0 $ipped in rust resistant alvanized 0 Jinc plated inside and out.All dimensions are in inches
Standa#d e#= ant Steel He% Ca"'AS E B16.* CLASS 1;0
8/9/2019 Tablas Weldolets, Thredolets
36/44
CominalEipe ize
Approx.9eight>bs. per
1 Eieces
3arton3ontents
1/,1/*)/,
1/'?
'*+
11
111
1? CIT A @# 16.) >H T#$
Available in both lac8 and alvanized inish.
GALVANI+EDSTEEL (ITTINGS(OR &LASTIC &I&E
ALE ADA&TER
Approx.9eight lbs. per
INSERT COU&LING CominalEipe ize
>ength:Hnches;
Co. of errations
Approx.
9eight lbs. per 1 Eieces
8/9/2019 Tablas Weldolets, Thredolets
37/44
1 Eieces CominalEipe ize
1/')/*>ength
:Hnches;Co. of errations
)) 1/,
++
1-''
11 1/*1 1/'
) 1/*) 1/'
*
+++
)*-'6
'' 1/'
*- )/*
+,
*1
) 6 , ',* + 1/* , *+
1/')/*
) )/,) )/,
++
1'1,
11 1/*1 1/'
) -/,) -/,* 1/*
+++
)-*-6+
'' 1/'
* 1/*+
+,
,''
) + , )'-
* , )/* , --
BRASS ALE ADA&TERS AND INSERT COU&LINGS AVAILABLE ON RE
8/9/2019 Tablas Weldolets, Thredolets
38/44
GENERAL IN(OR ATION (OR &I&E NI&&LES
ATERIALS END (INISHES@anufactured in accordance with A T@ pecification A+)) "9elded
and eamless 3arbon teel and Austenitic tainless teel Eipe Cipples"3arbon teel 0 9elded A-)0
#!9 A-) 0#eamless A1 6
>ow Temperature eamless A))) 0 rade 6
(INISHES3anvil steel nipples are available in blac8 or zinc coatings. Eleasespecify finish re4uired when ordering.
THREADS3anvil pipe nipples are threaded on both ends with standard tapered
pipe threads conforming to the American tandard for Eipe ThreadsAC H/A @# 1.' .1
Threads are right hand on each end unless otherwise specified. >efthandthreads or plain ends or combinations are available.
S&ECIAL LENGTHS3anvil can supply special lengths special threading and special finishes
to order.
LENGTH Cipples with lengths up through 1' in. long have a length tolerance of <1/16 in. Cipples over 1' in. long have a tolerance of < 1/, in.
IDENTI(ICATION:where practical;9elded 0
#!9 0
T$ none5 "Trademar8 5 "
tamping available upon re4uest
8/9/2019 Tablas Weldolets, Thredolets
39/44
eamless 0 "Trademar8 heat code schedule grade" blac8 phosphate finish for visual reference
TAN) LEGS
NEW (RO CANVIL Se"te, e#3 5000
FTAN) LEGSF• or use with standard teel Tan8s • Co cradle re4uired • Available in various sizes • Threaded Ine0#nd 5 4uare 3ut
• Available from stoc8 lac8
Eart K1 0 1/*" x 6" L'11'61 0 1/*" x +" L'11'+1 0 1/*" x ," L'11',1 0 1/*" x " L'11)1 0 1/*" x 1 " L'11)-1 0 1/*" x 1'" L'11*
8/9/2019 Tablas Weldolets, Thredolets
40/44
• 3ontact your 3anvil $istributor
SWAGED NI&&LES
ATERIALGnless otherwise specified 3anvil concentric
waged Cipples CE ' and larger are manufacturedfrom seamless pipe that meets the chemical andmechanical property re4uirements of A T@ A1 6
rade . They are mar8ed "A1 6 " :or "9E " inaccordance with fittings specification A T@ A')*;.
waged Cipples 1 1/' and smaller and all sizes of
eccentric waged Cipples are manufactured frommaterial that meets the chemical and mechanical property re4uirements of A T@ A1 -. They aremar8ed "A1 -" :or "9E ";. &exagon waged
Cipples CE 1 1/' and smaller are available onre4uest.
waged Cipples of alloy steel can be supplied uponre4uest.
utt welding ends conform with A @# 16. .
Threaded ends conform with A @# 1.' .1.
All dimensions are in inches. A""#$%. We ? t Ea= 3 &$und'
N$, nal O 'et $ & "eS !e Len?t
E==ent# =N ""le'
SCH80
SCH70
SCH160
SCHXXS
1/* x)/, x
1/' x
1/,1/*1/,
)/,1/*
' 1/*' 1/'' 1/'
' )/*' )/*
)/6*1/16+/6*
1/161/,
000
00
.1'
.1+
.1+
.'6.'6
.1+
.'*
.'*
.)6.)6
.'*
.)*
.)*
.-'.-'
A""#$%. We ? t Ea= 3 &$und'N$, nal O 'et $
& "eS !e Len?t
E==ent# =N ""le'
SCH80
SCH70
SCH160
SCHXXS
) x ' 1/''
1 1/'
1 1/*1
,,,
,,
1+/6*'-/6*) /6*
*-/6*--/6*
).*).*).*
).*).*
*.-*.-*.-
*.-*.-
6.)6.)6.)
6.)6.)
8/9/2019 Tablas Weldolets, Thredolets
41/44
)/* x1/,1/')/,1/*
' )/*)))
11/6*)/)'-/)'+/)'
0000
.'6.*.*.*
.)6.6.6.6
.-'.,.,.,
1 x
1 1/* x
1 1/' x
)/*1/')/,1/*1
)/*1/')/,1/*
1 1/*1
)/*1/')/,1/*
) 1/') 1/') 1/'
) 1/'*****
* 1/'* 1/'* 1/'* 1/'* 1/'* 1/'
-/6*11/6*1+/6*
'1/6*/6*
1-/6*'1/6*'+/6*)1/6*+/6*1/*
'1/6*'+/6*1+/)') /6*
000000000000000
.-
.-
.-
.-
.,
.,
.,
.,
.,1.'1.'1.'1.'1.'1.'
.+
.+
.+
.+1.11.11.11.11.11.+1.+1.+1.+1.+1.+
1.1.1.
1.1.61.61.61.61.6'.*'.*'.*'.*'.*'.*
' x
' 1/' x
1 1/'1 1/*
1)/*1/')/,1/*'
1 1/'1 1/*
1)/*1/'
6 1/'6 1/'6 1/'6 1/'6 1/'6 1/'6 1/'
++++++
1)/6*1 /6*' /6*1+/)'
-/,)/*
1)/16/6*
'1/6*+/16
)+/6*'1/)'
)/*
1.-1.-1.-1.-1.-1.-1.-'.)'.)'.)'.)'.)'.)
'''''''))))))
'.,'.,'.,'.,'.,'.,'.,*.'*.'*.'*.'*.'*.'
*******666666
)/*1/'
,,
1-/161 1/)'
).*).*
*.-*.-
6.)6.)
* x )' 1/'
'1 1/'1 1/*
1)/*1/'
'+/6*11/16-)/6*1 1/)'1 1/,
1 /)'1 ')/6*1 ' /6*
-.6-.6-.6-.6-.6
-.6-.6-.6
+.-+.-+.-+.-+.-
+.-+.-+.-
1111111111
111111
00000
000
- x *)
' 1/''
1 1/'1 1/*
1
11111111111111
' /6*+/,
1 /6*1 /)'
1 )1/6*1 )+/6*1 *+/6*
1)1)1)1)1)1)1)
1+1+1+1+1+1+1+
'*'*'*'*'*'*'*
0000000
6 x -*)
' 1/''
1 1/'1 1/'
1
1'1'1'1'1'1'1'1'
1)/)'+/,
1 1 /6*1 /16
1 *-/6*1 -+/6*
'' /6*
11111111
'-'-'-'-'-'-'-'-
00
)-)-)-)-)-)-
00000000
, x 6-*)
' 1/''
1)1)1)1)1)1)
6)/6*1 1)/)'1 --/6*' /)'
' )-/6*' 11/16
))))))))))))
************
000000
000000
8/9/2019 Tablas Weldolets, Thredolets
42/44
BULL &LUGS
ATERIAL
Gnless otherwise specified 3anvil ull Elugs CE ' and larger aremanufactured from seamless pipe that meets the chemical and mechanical property re4uirements of A T@ A1 6 rade . They are mar8ed "A1 6 " :or"9E " in accordance with fittings specification A T@ A')*;.
ull Elugs 1 1/' and smaller are manufactured from round or hex material thatmeets the chemical and mechanical property re4uirements of A T@ A1 -. Theyare mar8ed "A1 -" :or "9E ";.
Threads conform with A @# 1.' .1.
!ound ull Elugs are available in all regular schedules :A; and also in solidform : ;.
All dimensions are in inches. A""#$% ,ate We ? t Ea= 3 &$und'
N$, nal & "eS !e Len?t
SCH80
SCH70
SCH160 XXS
ROUNDSOLID
HEX.SOLID
HEX.SCH 70
1/,1/*)/,
1/')/*
''
' 1/*
' 1/'' )/*
0. ,.1'
.'.'6
0.1.16
.'*.)6
000
.)'.-
000
.*.6
.++
.1'
.''
.),.61
.1*
.1,
.'*
.*'.6
0.11.1-
.',.-1
1 1/*1 1/'
)) 1/*) 1/'
.6.6).
.,. *1.'
1.11.'1.6
1.'1.-'.
1.1.+).
1.)'.-).
.,11.)1.-
'' 1/'
*-
1.6'.,
'.'-).,
).)-.
*.6.,
*.-0
-.'0
'.*0
)) 1/'
66 1/'
*.6-.+
-.+.,
,.0
.1).-
00
00
00
* + .) 1 . 16. 1,.- 0 0 0
8/9/2019 Tablas Weldolets, Thredolets
43/44
(INISHwaged Cipples and ull Elugs are supplied blac8 with
rust protection unless zinc plating is specified.
ORDERING IN(OR ATION3 SWAGED NI&&LESEND CONNECTIONS
waged Cipples concentric and eccentric are available in threaded bevelled plain end or grooved connections or in any combination of suchend finishes.
or simplicity the following abbreviations may be used when orderingD
EXA &LE:a; ' x 1 ch , #33 wages Cipple >#T0 #:b; ) x ' ch * waged Cipple >#E0 #T:c; 1 x 1 1/' c2 16 waged Cipple T #:d; 1 sch * x )/* ch , waged Cipple ># 0 #T
# evelled oth #ndsT # Threaded oth #ndsE # Elain oth #nds># >arge #nd evelled>#T >arge #nd Threaded>#E >arge #nd Elain
# mall #nd evelled
#T mall #nd Threaded#E mall #nd Elain
N$te: :1;
:';
Gnless otherwise specified concentric waged Cipples will be supplied.
waged Cipples can be supplied with a differentschedule wall thic8ness at each end.
Steel
HOSE (ITTINGS$# (AST3 ECONO ICAL $'e =$nne=t $n' #e"a #'
8/9/2019 Tablas Weldolets, Thredolets
44/44
• Erecision engineered and matched to assureaccurate sizing and secure attachment of industrialhose with either bolt clamps or metal bands.
• $urable steel construction will stand up to punishing industrial and mining applications.
CO BINATION NI&&LES$esigned for easy adaptation of straight end industrial hoseto C.E.T. threaded fittings on pumps strainers valves etc.@ay also be attached to other lengths of hose by means ofa swivel female coupling.3an be used for most suctional and discharge applicationswhere moderated pressures are encountered. Elated nipplesare recommended where corrosion is encountered.N$t ntended $# =$,"#e''ed a #.
Available in plated or unplated steel. Sizes 1/2" to 6" Stainless Steel Sizes 3/4" to 4"
HOSE ENDERSHdeal for fast lasting on0the0spot repairs of damages hoseor for 2oining lengths of hose without the bul8 of swivelfittings.3an help minimize hose wastage when used to adapt short
or odd lengths of hose to meet specific needs.
Available in plated or unplated steel. Sizes 1/2" to 6"
Recommended