TestReport_4.1 RETs With RSU40 (UMTS2100) (Cascaded)

4.

4.1 RETs with RSU40 (UMTS2100)

Configuration file:

Upload to FTP server Z:\Common\Testing\TMA test\TestReport\ConfigFile

NB version :

Figure 4.1.1: NB SW version

4.1.1 Device Management

4.1.1.1 Cascaded RETs Devices Scan

Figure 4.1.1.1.1 shows AISG Device Scan in left nevigation tree , right click to scan AISG device.

Figure 4.1.1.1.1: Right click to scan AISG device

Figure 4.1.1.1.2 shows the protocol choose AISG 2.0, and Rack No is 4, Rack 4 is the RSU40 rack that

the RET connected.

Figure 4.1.1.1.2: Choose the rack to scan

It will take a while to scan , figure 4.1.1.1.3 shows 3 RETs are scanned.

Figure 4.1.1.1.3: Scan result

4.1.1.2 Add Cascaded RETs AISG Device

In left nevigation tree ,choose AISG device. Right click to choose "Linkage Scan Records Configure".

Figure 4.1.1.2.1: Right click to add AISG device

Figure 4.1.1.2.2 shows RET which serial number is KACSD4533585(shown on the lable of the antenna)

is connected to RSU40-U216(4,1,1)-Ret-1.The same way to add the other RET devices to rack 2 and

rack 7 respectively, as shown in figure 4.1.1.2.3 and figure 4.1.1.2.4.

Figure 4.1.1.2.2: Add RET to rack 4

Figure 4.1.1.2.3: Add RET to rack 2

Figure 4.1.1.2.4: Add RET to rack 7

Figure 4.1.1.2.5 shows 3 RETs are added .

Figure 4.1.1.2.5: RETs are added

4.1.1.3 Delete Cascaded RETs AISG Devices

Figure 4.1.1.3.1 shows right click to delete the AISG device.

Figure 4.1.1.3.1: Delete AISG device

4.1.2 Application Layer Test

4.1.2.1 Alarm Management

Unplug AISG cable between the second cascaded RET and the third cascaded RET, “RET

communication is interrupted”are reported. The alarms show in EOMS rack status illustration as figure

4.1.2.1.1 shows.

Figure 4.1.2.1.1: Real-time alarm in rack status illustration

4.1.3 Configuration Management

4.1.3.1 Reset AISG Devices– OMCB

Figure 4.1.3.1.1 shows choose one RET and right click to reset.

Figure 4.1.3.1.1: Right click to reset

Figure 4.1.3.1.2: RET(KACSD4533585) reset successfully

Figure 4.1.3.1.3: RET(KACSD4532791) reset successfully

Figure 4.1.3.1.4: RET(KACSD4533581) reset successfully

4.1.3.2 Devices Self-Check

Figure 4.1.3.2.1 shows choose one RET and right click to reset. The same way to other two RETs.

Figure 4.1.3.2.1: Right click to self test

Those RET self test successfully , as the below 3 figures shows.

Figure 4.1.3.2.2: RET(KACSD4533585) self test successfully

Figure 4.1.3.2.3: RET(KACSD4532791) self test successfully

Figure 4.1.3.2.4: RET(KACSD4533581) self test successfully

4.1.3.3 Version Information Query

Figure 4.1.3.3.1 shows right click to choose “Query Version”.

Figure 4.1.3.3.1: Right click to query version

Figure 4.1.3.3.2 to 4.1.3.3.4 shows the version information.

Figure 4.1.3.3.2: RET(KACSD4533585) version information

Figure 4.1.3.3.3: RET(KACSD4532791) version information

Figure 4.1.3.3.4: RET(KACSD4533581) version information

4.1.3.4 RET Antennas Automatic Calibration

Figure 4.1.3.4.1 shows choose one RET and right click to auto adjust.

Figure 4.1.3.4.1: Right click to auto adjust

Figure 4.1.3.4.1: RET(KACSD4533585) reset successfully

Figure 4.1.3.4.3: RET(KACSD4532791) reset successfully

Figure 4.1.3.4.4: RET(KACSD4533581) reset successfully

4.1.3.5 SET RET Antennas Tilt

Figure 4.1.3.5.1 shows right click to set tilt.Take 5 degree for example.

Figure4.1.3.5.1: Right click to set tilt

Figure4.1.3.5.2: Set tilt (RET KACSD4533585)

Figure4.1.3.5.3: Set tilt successfully

Figure4.1.3.5.4: Set tilt (RET KACSD4532791)

Figure4.1.3.5.5: Set tilt successfully

Figure4.1.3.5.6: Set tilt (RET KACSD4533581)

Figure4.1.3.5.7: Set tilt successfully

4.1.3.6 Query RET Antennas Tilt

Figure 4.1.3.6.1 shows right click to query tilt.It was set to be 5 degree in item 4.1.3.5.

Figure4.1.3.6.1: Right click to query tilt

Figure 4.1.3.6.2 to figure 4.1.3.6.4 shows the value of tilt .

Figure4.1.3.6.2: Query tilt result (RET KACSD4533585)

Figure4.1.3.6.3: Query tilt result (RET KACSD4532791)

Figure4.1.3.6.4: Query tilt result (RET KACSD4533581)