View
20
Download
0
Category
Preview:
Citation preview
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 1 -
KOT-F KOT-F (SUS BOX) KOT-F (SHIP PART) KOT-N (4~20mA) KOT-F (PULSE)
KOT 터빈유량계는 전자부분과 기계부분이 조합된 제품이며 체적식 유량계입니다. 원리는 흐르는 유체속에 축차
(회전각)가 유량에 비례적으로 회전, 속도가 증감합니다. 이 축차의 회전수를 픽업 코일이 감지하여 전기적 신호
(주파수)로 변화시켜서 현장 지시, 적산을 활성화시킵니다. 이 유량계의 축과 저널베어링은 텅스텐재질이고 유체의
종류에 따라서는 스테인레스 재질의 볼 베어링이 적용됩니다. 산업전반에 걸친 분야, 과학연구 등 유량 측정과 시
스템 제어에 광범위하게 사용되어집니다.
These flow meters are electromechanical, volumetric flow meters. The rotating angle increases in proportion
to the flow rate. The rotate rate is detected by the pick-up coil and converted into electrical signal,
activating local indicating totalizer. The flow meter's pole and journal bearings are manufactured with
tungsten, and stainless steel ball bearings and are applied according to the variety of the fluid.
■ 사양 (Specification)
■ Turndown Ratio : 10:1 ■ Flow Accuracy : ± 1% (@Liquid F.S), ± 1.5% (@Gas F.S) MFR STD'
■ Repeatability : ± 0.1%
■ Linearity : ± 0.1%
■ Pressure Rating : 5000 psi (Maximum)
■ Turbine Temperature : -30 〬 C ~100 〬 C (Option -90 〬 C ~ 170 〬 C)
■ End Connection : (NPT, PT), (JIS 10K, JIS 20K Flange), Etc.
KOT SERIES
■ 구조 (Structure) 및 치수 (Dimension)
Size L(mm)
6A 120
10A 120
15A 120
20A 120
25A 120
32A 160
40A 160
50A 170
65A 200
80A 230
100A 240
125A 240
150A 330
200A 390
KOT-F 250A 450
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 2 -
KOT Code Description
FluidL LIQUID
G GAS
Connection
Size
6 6mm (pipe screw thread G3/8")
10 10mm (pipe screw thread G1/2")
15 15mm (pipe screw thread G1")
25 25mm (pipe screw thread G1-1/4")
32 32mm (flange type)
40 40mm (flange type)
50 50mm (flange type)
65 65mm (flange type)
80 80mm (flange type)
100 100mm (flange type)
125 125mm (flange type)
150 150mm (flange type)
200 200mm (flange type)
250 250mm (flange type)
Connection
Type
F Flange
N Screw
S Sanitary Ferrule
Material
B SS304
C SS316
D SS316L
X PTFE / Special
Indicator InstallC Compact
S Separator
Power
TAAC Power / Local(Flow Rate & Totalizer) & 4~20mA.DC
/ Pulse
TDDC Power 4-WIRE / Local(Flow Rate & Totalizer) & 4~20mA.DC
/ Pulse
B Local Indication Totalizer (Battery Type)
LP DC 24V (2-Wire, Loop Powered)
Output & Comunication Protocol
R1 1-Dry Contact
R2 2-Dry Contact
A Only 4~20mA.DC
P Only Pulse
R RS 485
Option
NH 비방폭형 (Non-Explosion)
Ex 방폭형 (Explosion-Proof Type)
ST Strainer (Y형)
■ Model Code
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 3 -
■ 유량범위 (Flow Rate Table)
Size
LiquidGas
(@ATM. AMB)Size
Liquid Gas
Flow Rate
(m3/h)
Flow Rate
(L/min)
Flow Rate
(N㎥/h)
Flow Rate
(m3/h)
Flow Rate
(L/min)
Flow Rate
(N㎥/h)
2A 30 ~ 160(L/h) 0.5 ~ 2.67 - 50A 4 ~ 40 50 ~ 50016 ~ 160
65A 7 ~ 70 67 ~ 7504A 40 ~ 250(L/h) 0.67 ~ 4.17 -
80A 10 ~ 100 167 ~ 1667 35 ~ 3506A 100 ~ 600(L/h) 1.67 ~ 10 -
100A 20 ~ 200 334 ~ 333450 ~ 500
10A 0.2 ~ 1.2 3.33 ~ 20 -
125A 20 ~ 250 334 ~ 416715A 0.6 ~ 6 10 ~ 100
1.5 ~ 7.5150A 30 ~ 300 500 ~ 5000 100 ~ 100020A 0.6 ~ 7.2 10 ~ 120
25A 1.0 ~ 10 16 ~ 167
4 ~ 40
200A 50 ~ 500 834 ~ 8334 170 ~ 1700
250A 80 ~ 800 1334 ~ 13334 250 ~ 250032A 1.5 ~ 15 20 ~ 250
40A 1.8 ~ 20 30 ~ 350 8 ~ 80
■ Notice
■ 보관지점은 반드시 아래 조건을 구비해야한다. (Place keeps that must satisfy conditions as below.)
a) 방수, 방습 (Water-proof, Moisture-proof)
b) 기계진동이 작고 부딪혀 충격 받는 것을 피해야 한다.
Machine vibration must not be great, and prevent damage from bump.
c) 온도는 -30 ~ +60℃. 이상적인 온도는 25℃ 내외이다.
Keep temperature at -30 ~ +60℃. Ideal temperature is around 25℃.
d) 만약 실외에 오랜 기간 보관한다면 유량계의 성능은 영향을 받는다. 그러므로 실내 보관이 아니라면 가급적
바로 설치하는 것이 좋다.
Efficiency of flowmeter immediately receives influence if it is kept outside during long times. Thus,
flowmeter must be installed as soon as possible after it is delivered.
■ 설치지점을 선택하는데 반드시 주의해야할 사항 (Notice for installation)
유량계의 설계는 이미 열악한 환경 조건하에서의 상황을 고려하였다. 그러나 장기적으로 그 정확도와 안정
성을 유지하지 위해서는 설치지점을 선택할 시에 반드시 아래사항을 주의해야 한다.
Flowmeter was designed with considering inferior environmental conditions. However, user must notice
following articles when deciding place of installation to keep its accuracy and stability for long time.
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 4 -
a) 주변온도: 주변온도변화가 매우 심한 장소에 설치하는 것은 피해야한다. 만약 주변 설비의 열복사를 받지
않도록 하고 송풍, 환풍이 원활한 지점을 선택해야 한다.
Environmental temperature : Keep away from any place that has large change of environmental
temperature. If a device receives thermal radiation, user must keep it away from heat, and take any
action of ventilation.
b) 주변공기: 유량계를 부식성기체가 있는 환경 중에 설치하는 것을 피해야 한다. 만약 이러한 환경 중
에 설치해야 한다면 반드시 송풍, 환풍이 원활하도록 조치를 취해야 한다.
Environmental air: Keep away from any place that has corrosive gas. If this product must be installed
in this environment, user must provide any action of ventilation to it.
c) 기계진동과 충격: 유량계의 구조가 매우 견고하나 설치장소를 선택할 때 가급적 기계의 진동 혹은 충격을
받을 수 있는 장소는 피해야 한다. 만약 유량계를 비교적 진동이 큰 배관에 설치해야 한다면 배관을
지탱하여 진동으로부터의 영향을 최소화해야 한다.
Mechanical vibration and impact : Structure of flowmeter is very solid, but user must keep away from
mechanical vibration or damage from bump when deciding the place of installation, if it is possible.
If a meter is installed on a pipe with relatively great vibration, user must support a pipe.
*기타 : 설치와 유지보수 및 수리를 위하여 유량계 설치 장소에 반드시 충분한 공간이 있어야 한다.
Others : Must be enough space around installation place of flowmeter , maintenance, and repair.
■ 휴대용 무선 전화기, 무전기를 사용시 주의 사항
(Notice for limited use of wireless electric transceiver.)
유량계의 전자부분은 고주파의 방해에 영향을 방지하도록 설계되어 있으나 만약 유량계에 너무 가까운 곳에서
무선전화기, 무전기를 송수신한다면 고주파의 노이즈가 영향을 미칠 수 있다. 만약 필요에 따라 사용해야
한다면 사전에 유량계 설치장소에서 무선전화기, 무전기의 영향을 받는지를 점검 후 사용하도록 한다. 일정한
간격으로 유량계를 향해 이동하면서 영향을 받는지 여부를 점검한다. 만약 영향을 받는다면 영향을 미치지
않는 거리를 두고 사용하도록 한다.
Electronic part of flowmeter can block the interruption by high frequency electric noise. However, if
wireless electric transceiver is used in any place too close to flowmeter, interruption by high frequency
noise can have influence on flowmeter. Investigate the influence of wireless electric transceiver on
flowmeter, and its installed location(Check influence with moving wireless electric transceiver toward
flowmeter from place some meters away). If it receives influence, keep the transceiver away from that
place immediately.
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 5 -
■ 방폭형 유량계를 설치할 때 주의해야할 사항 (Notice for installing explosion proof type flowmeter)
유량계의 설계는 “폭발성 환경용 전기 설비 통용 요구(GB3836.1)”,“폭발성 환경용 폭발 방지 전기 설비 격폭
발형 전기 설비"d""및 ”폭발성 환경용 폭발 방지 전기설비 본질 안전형 전로와 전기 설비“i"”,“ 표준이 규정
한 바의 1구역과 2구역의 위험지역”에 사용할 수 있다.
Flowmeter was designed to be used for “common demands of electric facilities for explosive
environment(GB3836.1)”,“explosion preventative electric facilities for explosive environment and remote
explosive electric facilities "d"", ”nature of explosion preventative electric facilities for explosive
environment, stabilized converter, and electric facilities“i"”, and “danger zone in area 1 and 2 regulated
by the standard”.
■ 구조와 작동 원리 (Structure and operation principle)
∎ 터빈유량 감응신호장치의 기본구조 (Basic structure of turbine induced signal device)
감응신호장치의 기본구조는 아래 그림과 같다. 그것은 본체, 정방향 프레임, 터어빈날개, 역방향 프레임, 압력
프레임과 증폭기를 가진 픽업센서 등으로 구성되어있다.
Basic structure of induced signal device is as shown in below. It is composed of cover body,
frame leading forward, disc, frame leading backward, pressure frame, and induced electricity switch.
∎ 작동 원리 (Operation principle)
감응신호장치(픽업센서)와 자력으로 연결된 본체의 터어빈 날개가 유체에 의한 운동에너지의 힘으로 회전을
하며, 날개는 주기적으로 유도전기 감응시스템의 기저항값을 변화시키고, 코일을 통한 자력 선속은 주기적으
로 변화가 일어나서 전기 펄스신호를 발생시키며, 증폭기를 통해 확대하여 유량 변환기에서 그에 상응하는 유
량값으로 변환, PLC 또는 다른 지시계에 출력을 통해 유량값을 비례적으로 전송하며, 순시유량과 적산량의
측정을 가능하게 한다.
When measuring induced path signal device(pickup sensor) by fluid, disc in induced signal device spins
by employing the force of dynamic energy of fluid, disc changes original resistance value of induced
electricity system periodically, magnetic flux through coil creates electric pulse signal owing to
periodical change, then it is transmitted to corresponding flow accumulative meter, PLC, or upper digit
calculator after expanding amplifier, and progresses to measure flow or total amount.
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 6 -
Size
(A)
Flow range
Fluid
Temp.
Pressure
(barG)
Ambient
temp.
Relative
temp.
Max
pressure
loss
(mbar)
Basic error limit
0.2%
Basic error limit
0.5%
Basic error limit
1%
min. max. min. max. min. max.
2 0.03 0.16
-20~80
6.3
-20~55 ⪳80
0.15
4 0.04 0.25 0.12
6 0.1 0.6 0.1 0.66.3
16
25
32"
0.08
10 0.25 1.2 0.2 1.2 0.05
15 1.2 6 0.6 4 0.6 6
0.03525 2 10 1.6 10 1 10
40 4 20 3 20 2 20
16
25
0.025
50 6 40 4 40 4 40
65 6 45 4 45 4 45
80 16 100 10 100 10 100
100 25 160 20 160 20 200
16
25
125 30 250 20 250 20 250
150 50 300 40 300 30 300
200 150 750 100 600 50 500
250 200 800 160 800 80 800 16
■ 기술 성능 (Technical efficiency)
∎ 터빈유량 감응 신호 장치의 기술 성능 (Efficiency of turbine flow induced signal device)
터빈 유량 감응 신호 장치의 수직 지름 ,유량 범위, 유체 온도/압력, 상대온도, 최대 압력손실은 표1.을 참조.
Refer to table for nominal vertical diameter, flow range, fluid temperature, nominal pressure, relative
temperature, and maximum pressure loss of turbine flow induced signal device.
Table 1.
∎ 리튬건전지 방식 Battery type (Power supply from lithium battery)
- 정확도 (Accuracy) :
순시 유량 (Flow rate) : 0.5% of water conduction
적산량 (Total flow) : 0.1% of water conduction
- 주변 온도 범위 (Ambient temperature range) : -20 ~ 55℃
- 사용 온도 범위 (Medium temperature range) : -20 ~ 80℃
- 방폭 온도에 근거하여 각 해당의 유체 온도를 결정한다.
Decide medium temperature in each group on the basis of explosion proof temperature.
- 습도환경 : 상대습도 5~100% (결로현상이 없는 장소 선택)
Environmental humidity : relative humidity 5~100% (frostiness is not acceptable)
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 7 -
- 유량 변환기 외함 재질 : 알루미늄합금 재료
Material of transmitter housing : aluminium alloy
- 전원 : 3.6V 리튬 전지 (연속 사용시 수명 : 2~3년)
Power : 3.6V lithium battery (Life times : 1~3 years)
- 지시 : 6자리 LCD 및 유량측정 단위 지시
Display : 6-digit LCD Type and engineering unit display
- 유량(%), 순간유량, 적산유량등 6가지의 지시 방식이 있다.
Flow(%), flowrate, and accumulated flow has 6 coupling types of display
- 출력 (Outputs) : 기능 없음 (None)
- 저장기능 : 정전시 모든 데이터는 저장된다.
Memory function : All data is reserved when power is off
- 오차수정 : 5지점(4단계)로 나누어 수정
Error correction : Correct by dividing into 5 points(4 grades)
- 보호 등급 : IP65, 방수, 먼지방지
Protection class : IP65, water-proof, dust-proof
- 방폭 등급(Enclosure Class) : Explosion proof Ex ib I or Ex dHBT4
- 무게 (Weight) : 1.5 kg
∎ 전원 공급 방식 (AC. DC Power supply type)
- 순간 유량 : 도수의 0.5% (Flowrate : 0.5% of water conduction)
- 누계 유량 : 도수의 0.1% (Accumulated flow : 0.1% of water conduction)
- 주변 온도 : -20 ~ 55℃ (Environmental temperature : -20 ~ 55℃)
- 유체 온도 : -30 ~ 80℃, 고온은 문의 바람 (Medium temperature : -30 ~ 80℃)
- 방폭 온도에 근거하여 각 해당의 유체 온도를 결정한다.
Decide medium temperature in each group on the basis of explosion proof temperature
- 습도환경 : 상대습도 5~100% (결로현상이 없는 장소 선택)
Environmental humidity : relative humidity 5~100%(frostiness is not acceptable)
- 유량 변환기 외함 재질 : 알루미늄합금 재료
Material of transmitter housing : aluminium alloy
- 전원 (Power supply) : AC 250V, 50~60Hz, DC24V(4-Wire), DC24V(2-wire loop powered)
- 지시 : 6자리 LCD 및 유량측정 단위 지시
Display : 6-digit LCD Type and engineering unit display
- 유량(%), 순간유량, 적산유량등 6가지의 지시 방식이 있다.
Flow(%), flowrate, and accumulated flow has 6 coupling types of display
- 출력 (Outputs) : 4~20mA.DC & pulse
- 저장기능 : 정전시 모든 데이터는 저장된다.
Memory function : All data is reserved when power is off
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 8 -
- 오차수정: 단을 나누어 수정
Error correction: Correct by dividing grade
- 보호 등급 : IP65, 방수, 먼지방지
Protection class : IP65, water-proof, dust-proof
- 방폭 등급(Enclosure Class) : Explosion proof Ex ib I or Ex dHBT4
- 무게 (Weight) : 1.8 kg
■ 설치 (Installation)
∎ 설치 장소 (Place of Installation)
감응신호장치(픽업센서)의 사용 온도, 즉 측정 액체의 사용 온도는 기본 -20 ~ +80℃(그 이상의 온도 적용은
당사에 문의 바람)이며, 주변의 상대 습도는 80% 이하의 조건이다. 유지보수가 용이한 장소로 설치를 고려해
야 하며, 유량계의 탈,부착이 가능한 곳과 배관진동과 배관의 응력 영향이 없는 장소에 설치하도록 한다.
증폭기에 외란 방지를 위해 강한 열복사와 방사성의 영향을 받지 않도록 한다. 그리고 외부로부터의
강력한 전자기에 의해 코일에 영향을 주지 않도록 반드시 고려해서 설치한다. 만약 불가피하게 그러한 장소에
설치해야할 경우 감응신호장치의 증폭기 외부에 강력한 전자기를 차폐할 수 있는 덮개를 부가적으로 설치해야
한다. 그렇지 않으면 변환기의 정상 작업(예를 들면 유량 지시와 출력의 오동작)에 심각한 영향을 줄 수 있다.
Install in condition that liquid temperature measured by induced signal device is –20~+80℃,
standard(high temperature available, consult our factory), and relatively humidity is lower than80%.
Install in any place with considering easy installation, piping vibration, or influence of stress. If it is
possible, avoid strong thermal radiation and influence of radioactivity. Simultaneously avoid the
influence that external strong electromagnetic field has on inspecting and measuring coil. If it is not
possible, put a cover on amplifier of electric induced device, if not, transmitter will receive serious
influence in normal operation.
∎ 설치 위치 (Location of Installation)
감응신호장치는 일반적으로 수평설치를 해야 하며, 설치시 유량계 본체에 표시된 흐름 방향의 화살표를 유체
의 유동 방향과 서로 부합되게 해야 한다. 수직배관에 설치를 해야 하는 경우 유체의 유동 방향을 아래에서
위로 흐르게 하여 측정 지점에서 유체가 만수 상태로 측정될 수 있도록 해야 한다.
Induced signal device generally should be installed horizontally, and an arrow of flow direction on
turbine flowmetert must meet the flow direction of fluid each other when installing. If it must be
installed vertically, make fluid flow upward from bottom to guarantee that fluid can be fully filled in
flow induced signal device.
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 9 -
- Reducer pipe: L=15D
- Connecting to single bent pipe: L=20D
- Connecting to double bent pipes
L=20D (one plane)
L=20D (two planes)
- Connecting to right-angled curved pipe:
L=20D
- If there is finishing valve
L=20D (all valves are full-opened)
L=50D (all valves are semi-opened)
∎ 배관 요점 (Points of Piping)
- 액체의 와류 현상과 유속이 고르지 않음을 제거하기 위해 유량계의 전단, 후단에 직관부 혹은 정류기
를 고려해야 한다. 일반적으로 상류부분(유량계 전단)의 직관부 길이는 10 ~ 20D(D는 배관의 구경), 하류부
분(유량계 후단)의 직관부 길이는 5D이며, 직관부는 축관이나 확관이 아닌 유량계의 관경과 일치해야 한다.
그렇지 않으면 측정의 오차가 발생하게 된다.
Arrange straight pipe section or rectifier in inlet of induced signal device to remove uneven vortex
and flow velocity of fluid. Generally, the length of straight pipe section in upstream area(inlet) is
15~20D(D is the nominal diameter of flowmeter). The length of straight pipe section in
downstream(outlet) is 5D, and the diameter of straight pipe section and the nominal diameter of
flowmeter must be the same each other. If not, there can be any error(reducer pipe or expander
pipe).
straight pipe section in upstream and downstream area
또한, 더욱 효율적인 와류 제거를 위하고 유량측량의 정밀도를 높이려면 상류부분(유량계 전단)의 직관부에
파이프로 구성된 정류기를 배치해야 한다. 정류기 상류부분의 직관부 길이는 10 ~ 20D이다.
Also if measured precision is increased to remove parasitic electricity more effectively, rectifier made
up with pipe in straight pipe section in upstream area can be introduced. The length of straight pipe
section installed in upstream area of rectifier is 10~20D.
- 유체중의 불순물을 제거하기 위해 유량계의 정상 동작 요소를 확보해야 하며 유량계의 수명을 높여야 한다.
유량계의 상류부분에 3~9 neck/cm²의 여과기를 설치할 것을 권장 한다. 일반적으로 배관경의 대소 여부와
여과기의 여과성능(조밀성)은 밀접한 관계가 있다. (배관경이 작아질수록 조밀해진다.) 유량계의 정상 동작을
보장하기 위해서는 여과기의 조밀성을 선별 사용하여야 한다.
Induced signal device must be normally operated, and it must have long life to remove impurities in
fluid. Filter with 3~9 neck/cm² must be installed on pipe line of induced signal device. If vertical
diameter is greater in general condition, the number of neck is rare, and if vertical diameter is
smaller, the number of necks is dense. User must selectively use the number of filter necks to ensure
normal operation of induced signal device on the basis of actual situation.
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 10 -
Mixture of air separator and filter(공기분리) Rectifier(정류기)
- 유량계의 연결부 용접 작업시, 반드시 파이프 내부에 돌출된 부분이 없어야 한다. 용접된 플랜지나 피팅류와
유량계 본체와의 둘레는 일치하는 것이 좋다. 한쪽으로 치우치거나 매끄럽지 않으면 유속이 고르지 못하게
분포하는 현상으로 유량계를 올바르게 사용할 수 없다.
When welding connection of flowmeter, there must be no projected part in pipe. When it is
connected to flange or fitting for thread, external diameter of two welded parts must be perfectly
same, and inner parts must not be exposed in pipe. If it is connected to different diameter, velocity
can be unevenly distributed. Thus, it cannot be used.
- 유지보수 또는 수리가 용이할 수 있도록 유량계 설치 지점의 전후 배관에 밸브를 설치하고 우회 배관을
설치해야 한다. 유량 제어용 밸브는 유량계의 하류부분(후단)에 설치해야 한다. 유량계의 유량 측정시 상
류부분(전단)에 설치한 밸브는 반드시 완전 개방하여 유체의 와류현상을 방지해야 한다.
Install cutting valve(finishing valve) on pipe at upstream and downstream side of flowmeter and install
bypass at the same time to ensure the necessity of inspection and repair under operation condition.
Flow control valve must be installed in downstream of flowmeter. When using flowmeter, finishing
valve installed in upstream must be opened to prevent fluid in upstream from parasitic
phenomenon.
- 지나치게 큰 유량이 감응신호장치를 통과할 때, 즉 유량범위의 상한선을 초과하게 되면 베어링은 과도한 속
도변화로 인해 급속하게 마모가 촉진된다. 따라서 과도한 유량이 예상될 경우는 사전에 하류부분에 설치된
밸브를 이용하여 유량을 조절해야 한다.
When fluid passed through induced signal device is too large(exceed over the maximum of flow
range), bearing promotes to be worn down if the change of its velocity is too large. Accordingly,
when calculating any potential situation of overflow in advance, fluid flow can be controlled with flow
control valve installed in downstream area.
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 11 -
KOTS Series의 로터는 유체의 운동에너지에 비
례하여 회전한다. 이 때 발생되는 펄스는 K 팩
터와 출력 신호로 활용할 수 있다.
The rotor is turned by the fluid force in flow
proportional way. A hall generator supplies
pulses, which can be utilized for digital or
analogue signal processing.
The generated pulses are specified as the
k-factor.
KOTS Code Description
FluidL LIQUID
G GAS
Connection
Size
8 1/4” (N)PT (FEMALE)
10 3/8” (N)PT (FEMALE)
15 1/2” (N)PT (FEMALE)
20 3/4” (N)PT (FEMALE)
Connection
Type
F Flange
N Screw
S Sanitary Ferrule
Connection
Material
B SS304
C SS316
P PVC
X Special
Indicator InstallC Compact
S Separator
Power
TA AC Power / Local(Flow Rate & Totalizer) & 4~20mA.DC / Pulse
TDDC Power 4-WIRE / Local(Flow Rate & Totalizer) & 4~20mA.DC /
Pulse
B Local Indication Totalizer (Battery Type)
LP DC 24V (2-Wire, Loop Powered)
Output & Comunication Protocol
A Only 4~20mA.DC
P Only Pulse
R RS 485
OptionEx 방폭형 (Explosion-Proof Type)
ST Strainer (Y형)
KOTS SERIES
■ Model Code
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 12 -
Type (KOT Series) KOTS-7 KOTS-6 KOTS-5 KOTS-4 KOTS-3 KOTS-2 KOTS-1
Article no (standard) 167523 167512 167525 167513 167514 167515 167516
Article no (with cable) - 167522 - 167517 167519 - -
Measuring range L/min 2~35 1~25 1.5~25 1~15 0.50~7.5 1~10 0.5~5
K-Factor PPL* 700 1000 1000 2200 4600 3300 6900
Size (mm) 8 8 8 8 8 8 8
Material Grilamid TR55 (PA 12) Polyamid 12
Viscosity range 0.8 ~ 16 mm2/sec
Accuracy ±2% of value
Repeatability 0.50%
Temperature range(℃) -20 ~ 100
Operating pressure 25 bar max
Burst pressure 200 bar
Electrical connection AMP Faston 2,8 / 6,3 x 0.8mm
Power supply 5~24 VDC
Current consumption Ca. 8mA
Output signal Pulses by open collector NPN
Pull-down resistor 1 ~ 2,2 k0hm
Connections Male threads 3/8"
Type KOTS-7 KOTS-6 KOTS-5 KOTS-4 KOTS-3 KOTS-2
1 L/min ~ 0 ~ 0 ~ 0 ~ 0 ~ 0 ~ 0
2 L/min ~ 0 ~ 0 0.05 ~ 0 0.06 ~ 0
5 L/min ~ 0 0.05 0.2 0.05 0.2 0.12
10 L/min ~ 0.12 0.17 0.4 0.2 0.7 0.4
15 L/min ~ 0.25 0.27 - 0.4 - 0.9
20 L/min ~ 0.45 0.48 - 0.7 - 1.3
25 L/min ~ 0.60 0.65 - - - -
30 L/min ~ 0.92 0.97 - - - -
■ 특징 (Features)
■ 저렴한 가격 (Low cost) ■ 소구경, 미소유량 측정에 적합 (Small size & low flow)
■ 쉽고 빠른 설치 (Easy and fast installation) ■ 용이한 유지보수 (Maintenance free)
■ 고압 배관에 적용 (High operating pressure) ■ 수평, 수직 배관 설치 (Installation in any position)
■ 기술 사양 (Technical Data)
* PPL = Pulses / liter Connections also available with cable
■ 압력 손실표 (Pressure drop table) (Unit : bar in water)
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 13 -
■ 구조 (Structure) 및 치수 (Dimension)
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 14 -
KOTQ Series는 온도와 압력 보상이 가능한 가스
터빈 유량계입니다.
Temperature and Pressure compensation,
normative flow can be displayed .
Application range Gas: Natural Gas, LPG, Air(1) Dry gas without water(2) Gas without corrosion
Measured Value
Primary measured value Flow Rate
Secondary measured value Volume flow
Tertiary measured value Temperature; Pressure (ONLY available for compensation model)
Features
Modular construction The measurement system consists of a flow sensor and a signal converter. It is available as compact and as separate version.
Compact version converter Compensation Type
D1: Local Display; 24V DC Power; Dual Power: Battery;4-20mAOutput(3-wire);SIRERS485
D2: Local Display: 24V DC Power; Dual Power: Battery;4-20mAOutput(2-wire);ModbusRS485
Connection Thread: DN25-DN50
Flange: DN25-DN300 (DIN, ANSI, JIS)
Measurement Ratio Standard – 10:1; Optional: 20:1
KOTGQ SERIES [Temperature and Pressure Compensation]
■ Technical Data
Measuring system
Design
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 15 -
Reference conditions Flow conditions similar to ISO 9951
Medium: Gas
Temperature: +10...+30°C / +50...+86°F
Inlet section: ≥ 10 DN
Operating pressure: 1 bar / 14.5 psig
Flow Meter Accuracy Standard: 1.5% Qmin to 0.2Qmax: 3%; 0.2Qmax to Qmax: 1.5%
Optional: 1.0% Qmin to 0.2Qmax: 2%; 0.2Qmax to Qmax: 1.0%
Temperature
Process temperature -20...+80°C
Ambient temperature(all versions)
Standard (with aluminum converter housing):
-10…+55°C
Storage temperature -20...+70°
Pressure
EN 1092-1 DN25…DN300: PN 16
Other pressures on request
ASME B16.5 1”...12": 150 lb RF
Other pressures on request
JIS 1”...12": 10 K
Other pressures on request
Installation For detailed information see chapter "Cautions for Installation"
Flow direction Forward
Arrow on flow sensor indicates flow direction.
Inlet run ≥ 10 DN
Outlet run ≥ 5 DN
Sensor housing SS304
Other materials on request
Flanges SS304
Other materials on request
Rotor ABS Plastic (Acrylonitrile - Butadiene – Styrene)
Aluminum Alloy
Bearings and Shaft SS304
Converter Housing Standard: polyurethane coated die-cast aluminum
Measuring accuracy
Operating conditions
Installation conditions
Materials
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 16 -
Model Suffix Code Description
KOTGQ-
Converter
D1-Local display; 24V DC and Battery Power; 3-wire 4-20mA OutputSURE RS485 Protocol
D2-Local display; 24V DC and Battery Power; 2-wire 4-20mA OutputModbus RS485 Communication
Diameter XXX
Three Digitals; for example:025: 25 mm; 050: 50 mm;125: 125 mm; 300: 300 mm
Flow rangeS(x) Refer to flow range table
W(x) Refer to flow range table
Body MaterialS SS304
L Cast Aluminum
Rotor MaterialS ABS Plastic
L Aluminum Alloy
Explosion LevelN Safety Field without Explosion
E1 ExiaIICT4
E2 ExdIIBT6
Connection
-DXX
DXX: D06, D10, D16, D25, D40D06: DIN PN6; D10: DIN PN10D16: DIN PN16; D25: DIN PN25D40: DIN PN40
-AXAX: A1, A3, A6A1: ANSI 150#; A3: ANSI 300#A6: ANSI 600#
-JX JX: J1, J2, J4J1: JIS 10K; J2: JIS 20K; J4: JIS 40K
-TH Thread; DN4…DN50
Accuracy-N 1.5%
-G1 1.0%
■ Model and Selection
Table 1: Model Selection Guidance for Gas Turbine Flowmeter
Model Code: LWQ-D1-100S1SLN-D16-N
Explanation - Converter: battery power mode without output; Diameter: 100mm; Flow range: 20-400 m3/h; Body Material: SS304; Rotor Material: Aluminum Alloy; No Explosion; Connection: DIN PN16 Flange; Accuracy: 1.5%
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 17 -
Nominal Diameter Standard Flow Range (SFR) Extended Flow Range (EFR)
Standard Pressure Rating
(mm) (in.) Code (m3/h) Code (m3/h) (MPa)
25 1 S 2.5 to 25 W 4 to 40
1.6
40 1.5 S 5 to 50 W 6 to 60
50 2S1 6 to 65 W1 5 to 70
S2 10 to 100 W2 8 to 100
65 2.5 S 15 to 200 W 10 to 200
80 3S1 15 to 300
W 10 to 160S2 20 to 400
100 4S1 20 to 400
W 13 to 250S2 32 to 650
125 5 S 25 to 700 W 20 to 800
150 6S1 32 to 650
W 80 to 1600S2 50 to 1000
200 8S1 80 to 1600
W 50 to 1000S2 130 to 2500
250 10S1 130 to 2500
W 80 to 1600S2 200 to 4000
300 12 S 200 to 4000W1 130 to 2500
W2 320 to 6500
400 16 S 400 to 8000 W 260 to 8000
Warning: Precaution for direct sunshine and rain when the meter is installed outside.
Measurable Flow Rate Range:
Note: The flow range as blow is based on operating status; REFERENCE ONLY. Consult the factory if you have special requirement. Refer to the nameplate or certificate for actual flow range.
■ Cautions for Installation
Mounting Positions
Avoid all pipe locations where the flow is pulsating, such as in the outlet side of piston or diaphragm pumps.
Avoid locations near equipment producing electrical interference such as electric motors, transformers, variable frequency, etc.
Install the meter with enough room for future access for maintenance purposes.
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 18 -
Required Lengths of Straight Runs
Flow altering device such as elbows, valves and reducers can affect accuracy. See diagram below for typical flow meter system installation.
Diagram 1. Typical Flow Meter System Installation
The recommended guidelines are given to enhance accuracy and maximize performance. Distance given here are minimum requirements; double them for desired straight pipe lengths.
◾ Upstream: allow a minimum straight pipe length at least 10 times the internal diameter of the
pipe. For example, with the 50mmpipe, there should be 500mm of straight pipe immediately
upstream. Desired upstream straight pipe length is 1000mm.
◾ Downstream: allow a minimum straight pipe length at least 5 times the internal diameter of
the pipe. For example, with the 50mm pipe, there should be 250mm of straight pipe immediately
upstream. Desired upstream straight pipe length is 500mm.
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 19 -
Diameter (mm) L (mm) Thread
Criteria
25 170 G 2”
40 140 G 2”
50 150 G 2-1/2”
Special Notice
¨ Foreign material in the liquid being measured can clog the meter’s rotor and adversely affect accuracy. If this problem is anticipated or experienced, install screens to filter impurities from incoming liquids.
¨ To ensure accurate measurement, drain all air from the system before use.
¨ When the meter contains removable coverplates. Leave the coverplate installed unless accessory modules specify removal. Don’t remove the coverplates when the meter is powered, or electrical shock and explosion hazard can be caused.
■ Connections
Thread Connection
Note: Default Thread is Male G Thread, other thread are available on request. For example: Female NPT Thread, Male NPT Thread; Consult FLOWNICS for more information
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 20 -
ANSI Flange Meter Dimensions
Size Code A ANSI Flange Rating Class
Flange Diameter
(B)
Bolt Hole Diameter
Bolt Circle Diameter
(PCD)
Bolt Hole Quantity
(inch) (mm) (mm) (mm) (mm) (mm)
1" 25 170 150 108 16 79 4
300 124 19 89 4
1-1/2" 40 200 150 127 16 99 4
300 155 22 114 4
2" 50 200 150 152 19 121 4
300 165 19 127 8
2-1/2" 65 240 150 180 19 140 4
300 190 22 149 8
3" 80 240 150 191 19 152 4
300 210 22 168 8
4" 100 300 150 229 19 191 8
300 254 22 200 8
5" 125 240 150 255 22 216 8
300 280 22 235 8
6" 150 450 150 279 22 241 8
300 318 22 270 12
8" 200 500 150 343 22 298 8
300 381 25 330 12
10" 250 500 150 460.4 25 362 12
300 444.5 28.4 387.3 16
12" 300 300 150 482.6 25.4 431.8 12
300 520.7 31.8 450.9 16
Flange Connection
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 21 -
DIN Flange Meter Dimensions
Size Code A DIN Flange Pressure Rating
Flange Diameter
(B)
Bolt Hole Diameter
Bolt Circle Diameter
(PCD)
Bolt Hole Quantity
(inch) (mm) (mm) MPa (mm) (mm) (mm)
1" 25 170 1.6 115 14 85 4
1-1/2" 40 200 1.6 150 18 110 4
2" 50 200 1.6 165 18 125 4
2-1/2" 65 240 1.6 185 18 145 4
3" 80 240 1.6 200 18 160 8
4" 100 300 1.6 220 18 180 8
5" 125 240 1.6 250 18 210 8
6" 150 450 1.6 285 22 240 8
8" 200 500 1.6 340 22 295 12
10" 250 500 1.6 405 26 355 12
12" 300 300 1.6 460 26 410 12
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 22 -
KOTM 터빈유량계는 미소 유량 측정을 위한 것으로 고온 고압의 조
건 하에서 매우 높은 정확도를 갖는다. 전자 신호 출력이 가능하여
1%의 정확도 및 반복성 0.2%를 유지할 수 있습니다.
Mini flow meter is based on turbine theory and designed for
measuring micro-flow. This meter has extremely high accuracy
especially under the condition of high temperature and high
pressure.
The Electronic pulse transmitter is also integrated in this mini flow
meter. it can maintain the 1% accuracy and the 0.2% repeatability.KOTM
MODEL KOTM-1 KOTM-2
Flow Range
(Diameter)
1.1mm 2.1 ~ 90 L/hr
1.2mm 3.06 ~ 108 L/hr
1.4mm 5.04 ~ 138 L/hr
1.5mm 5.58 ~ 150 L/hr
Accuracy ± 1.5 % ± 1 %
Repeatability 0.25 %
Display No Yes
Signal Output Pulse 4~20 mA
Power Supply +24VDC±15%
Material
Housing : Green Brass
Bearing : Stainless Steel
Rotor : PVDF
Magnet : Ceramin
Seal Ring : MVQ
Protection Level IP 60 IP 65
Diameter 1.1mm~1.5mm
Temperature -10℃~+100℃
Pressure Rating 2MPa
Connection G 1/4 Thread Female
Dimension 55 * 40 * 47 mm
KOTM SERIES
■ Technical Specification
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 23 -
KOTK-24 터빈유량계는 전자부분과 기계부분이 조합된 제품이며
체적식 디젤 기어 유량계입니다.
높은 정확도와 작은 사이즈의 제품으로 유지 관리 또한 쉽습니다.
These flow meters are electromechanical, volumetric flow diesel
gear flow meter.
High Accuracy easy maintenance compact size.
Inlet and Outlet NPT 1”, BSP 1”
Body Material PPS
Flow Range 5~50 GPM (18.9~190 LPM)
Accuracy ±0.5%
Repeatability Error 0.1%
Pressure Class 10Bar
KOTK-24 SERIES
■ Specifications
- High accuracy, Duarble, Compact
- Easy maintenance
- Two cumulants (resetting, and accumulating)
- Gallon or Liter Opetion
- PPC Body
- Also for chemical industry, medicine and other corrosive medium measurement.
■ Technical Specification
Turbine Flow Meter
인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체
(주) 플 로 우 닉 스
T E L : 82-32-579-2999
E-MAIL : kms2002@kofi.co.kr
- 24 -
KOTW 터빈유량계는 높은 정확성과 내구성을 갖춘 소형 사이즈의 제
품으로 출력 모듈을 사용할 수 있습니다. 장거리 전송 및 디스플레이
설정이 간단하며 조립 및 유지보수가 용이합니다. 리튬전지는 9천 시
간동안 전원을 제공합니다.
High accuracy, Durable, Small volume turbine flowmeter, Module
design can be used with output module. sensor and long-distance
transfers, The features of the display : 2 cumulants (1 resetting, 1
accumulating); optional unit conversion of Gallon and Liter. It is
easy to change the spare parts inside, and easy to maintain. It is
easy to assemble as its compact design. Lithium battery, can
supply 9000hours power.
MODEL WLL1 WLL40
Threaded Joint of the Inlet and Outlet NPT 1”, BSP 1” NPT 1.5”, BSP 1.5”
Material Aluminum
Flow Range 5~50 GPM (18.9~190 LPM) 10~100 GPM (38~380 LPM)
Accuracy ±1.0% ±0.5%
Repeatability 0.1%
Pressure Class 300PSI / 21BAR
Material of Connected Parts
Body Aluminum
Bearings Ceramics
Shaft Tungsted Carbide
Rotor PVDF
Supposed Filter Dimension 55 mesh
KOTW SERIES
■ Technical Specification
Recommended