View
1.787
Download
110
Category
Preview:
DESCRIPTION
Tutorial on 2d Hybrid Meshing in ICEM CFD for 2d Airfoil
Citation preview
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
Tutorial on 2d hybrid meshing in ICEM CFD for 2d airfoil
1. Objective: To make the hybrid mesh in ICEM CFD for an airfoil.
2. Learning objectives:
To make the hexa mesh in vicinity of airfoil Tetra mesh (patch dependent) in outer domain with conformal mesh at
boundary Merging of two meshes. Here two methods are given for better understand of
process. Exporting mesh and importing in Fluent and sample solution
3. Importing geometry Geometry is available in formatted .dat format
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
Airfoil
Interfaceboundary
Fairfield
Pressureoutlet
Then I added smaller far field boundary (interface between hexa and tetra mesh, called interfacecurves) and scaled it to get the outer most boundary (called far field) . Faces were also made and after that I run build topology to segment surfaces automatically. I have also deleted inner most surface(inside airfoil).
.
Outerdomainmeshingwithtetra
innerdomainmeshingwithhexablocking
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
Set these parameters in part mesh setup
After that 2d planner block is created as shown in Fig. After usual processing C-type blocking was made and mesh was converted to unstructured mesh
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
Now update mesh sizes for blocking and specially at boundary of inner mesh which will be used for the outer mesh.
Now create pre-mesh and check the mesh for any error.
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
Mesh will look like as follows.
Convert to unstructured mesh
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
Now hide inner domain from model tree. Also turn on surfaces so that we can pick outer surface/domain while meshing. This tetra mesh will be merged with previously created hexa mesh.
Method selected is patch dependent mesh and All Tri. Also check Respect line elements. This is necessary since at interface we need same mesh on both sides.
Since we have already defined mesh sizes for all parts (surfaces and curves).
Now go to compute mesh panel (surface mesh, first option from left) and choose visible option for input.
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
Mesh looks like as shown in following Fig.
Now turn-on the inner mesh also (Hexa one)
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
You can notice two colors for mesh inside and outside. This is due to fact that both meshes are in different part.
First step in merging 2d meshes is to make single part for both meshes. For this right click on outer part model tree,
Now you see both meshes are combined together. But if you export mesh without doing this you will get wall between both domains (inner and outer).
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
Method one defining interior boundary condition for interfacecurves and output mesh.
Interfacecurves
Farfield
intisaddedbyICEM
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
When I simulated this case in Fluent, results are not different than the case without the interior boundary.
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
Method two Deleting line elements in interface zone. There are two methods to do this
a) delete the interface part (assuming you have separate part for the interfacecurves, which we have).
Go to Geometry > delete curves and choose part which contains the interfacecurves
No export mesh from ICEM and import into Fluent
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
Results are :
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
Method three Deleting interface elements when you have not defined separate part for interfacecurves
In this case disable all other elements type and only leave the line elements.
Lineelementsareselectedininterfaceregion.
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
.
+923215096447 Copyrightbyhttp://cfdconsultancy.webs.com/turboenginner@gmail.com
Summary:
1. We have learned how to tackle the hybrid 2d mesh in ICEM CFD. 2. It should be noted that the hybrid meshing for 3d cases is different than 2d. I will
show it in separate tutorial. 3. We have discussed three methods to make hybrid mesh. 4. All files at each stage are also included in package.
Recommended