View
244
Download
2
Category
Preview:
Citation preview
Smoke Detector Model NumberSystem Sensor
14002400
C2W-BAGE/Edwards
Max Number of Detectors/CircuitMax Number of C2M Series/Circuit
Legend: √ = CompatibleX = Not Compatible
Notes: (1) Must use specified base (do not substitute with System Sensor branded bases)(2) C2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (C2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit(5) EDWB110RLP and EDWB401BR both contain current limiting resistors and are for use with specified panels only(6) Each detection circuit must employ a single model number of smoke detector (does not apply to detectors employing plug-in bases) - DO NOT MIX TECHNOLOGIES
Compatibility Issues: 1. Is there a remote LED indicator?2. Does the smoke detector have a relay base?3. Check total number of detectors on a circuit does not exceed the recommended maximum.
1151¹1151¹1151¹2151¹2151¹2151¹1451¹1451¹1451¹1451¹2451¹2451¹2451¹2451¹
C2M-PD1²C2M-PDC³
C2M-PDHC³C2M-PDHRC³
Copyright © 2008 by Frank Kurz (All Rights Reserved)
EDWARDS/GE Panel Model Number 1527 2280Base
NA X XNA X X
EDWB110LP X XEDWB116LP(RLY) X X
EDWB110RLP X XEDWB110LP X X
EDWB116LP(RLY) X XEDWB110RLP X X
EDWB401B X XEDWB406B(RLY) X X
EDWB401BR X XEDWB406BR(RLY) X X
EDWB401B X XEDWB406B(RLY) X X
EDWB401BR X XEDWB406BR(RLY) X X
NA X X
NA √² √²NA X XNA X XNA X X
NA NA30 30
(1) Must use specified base (do not substitute with System Sensor branded bases)(2) C2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (C2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit(5) EDWB110RLP and EDWB401BR both contain current limiting resistors and are for use with specified panels only(6) Each detection circuit must employ a single model number of smoke detector (does not apply to detectors employing plug-in bases) - DO NOT MIX TECHNOLOGIES
2. Does the smoke detector have a relay base?3. Check total number of detectors on a circuit does not exceed the recommended maximum.
V = VERIFIEDNV = NONE VERIFIED
© 2008 by Frank Kurz (All Rights Reserved)
6601 6602/6604 6616/6632 EST1-1Z1 EST1-2Z3/2Z6
√ √ √ √ √X X X X X√ √ √ √ √X X √ X XX X X X X√ √ √ √ √X X √ X XX X X X X√ √ √ √ √X X √ X √X X X X XX X √ X √√ √ √ √ √X X √ X √X X √ X √X X X X XX X X X X
√ √ √ √ √
√³ √³ √³ √³ √³√³ √³ √³ √³ √³30 30 30 30 3030 30 30 30 30
(2) C2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (C2M-PDC has "Clean Me" technology and may NOT function with some panel models)
(6) Each detection circuit must employ a single model number of smoke detector (does not apply to detectors employing plug-in bases) - DO NOT MIX TECHNOLOGIES
√³ √³ √³ √³ √³
ESA 6500 8500 (IDC) 8500 (ZAM) 4 wire 8500 ESAC
√ X √⁴ √ √⁴X X X X X√ X √ √ √X X √ √ √√ √ X X X√ X √ √ √X X √ √ √√ √ X X XX X √ √ √X X √ X √√ √ X X X√ √ X X XX X √ √ √X X √ √ √X X X X √√ √ X X XX X X X X
√ √ √ √ √
√³ √³ √³ √³ √³X √³ √³ X √³
30 30 3030 30 30
√³ √³ √³ √³ √³
30⁴ 30⁴30⁴ 30⁴
IRC3 (ZB8)
X √ √ √X X X X√ √ √ √√ √ √ √X X X X√ √ √ √√ √ √ √X X X X√ √ √ √√ √ √ √X X X X√ √ √ X√ √ √ √√ √ √ √√ √ √ √X X X XX X X X
√ √ √ √
√³ √³ √³ √³√³ √³ √³ √³30 30 30 3030 30 30 30
IRC3 (RZB) NV IRC3 (SIGA-UM) V IRC 3 (SIGA-UM) NV
√³ √³ √³ √³
EST2 (SIGA-UM) EST3 (IDC) EST3 (SIGA-UM)
√ √ √X X X√ √ √√ √ √X X X√ √ √√ √ √X X X√ √ √√ √ √X X XX X X√ √ √√ √ √√ √ √X X XX X X
√ √ √X
√³ √³ X√³ √³ X30 30 3030 30 30
√³ √³
Mirtone Panel Model NumberSmoke Detector Model Number BaseSystem Sensor
1400 NA2400 NA
MTB110LPMTB116LP(RLY)
MTB110RLPMTB110LP
MTB116LP(RLY)MTB110RLP
MTB401BMTB406B(RLY)
MTB401BRMTB406BR(RLY)
MTB401BMTB406B(RLY)
MTB401BRMTB406BR(RLY)
C2W-BA NAGE/Mirtone
NANANANA
Max Number of Detectors/CircuitMax Number of CM2M Series/Circuit
Legend: √ = CompatibleX = Not Compatible
Notes: (1) Must use specified base (do not substitute with System Sensor branded bases)(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit with System Sensor 1151/1451 or System Sensor 2151/2451(5) MTB110RLP and MTB401BR both contain current limiting resistors and are for use with specified panels only(6) Each detection circuit must employ a single model number of smoke detector - DO NOT MIX TECHNOLOGIES and observe limit numbers.
Compatibility Issues: 1. Is there a remote LED indicator?2. Does the smoke detector have a relay base?3. Check total number of detectors on a circuit does not exceed the recommended maximum.4. In instances where there are NO detectors listed, the control panel must be changed and the entire fire alarm system verified.
1151¹1151¹1151¹2151¹2151¹2151¹1451¹1451¹1451¹1451¹2451¹2451¹2451¹2451¹
CM2M-PD1²CM2M-PDC³
CM2M-PDHC³CM2M-PDHRC³
Copyright © 2008 by Frank Kurz (All Rights Reserved)
7124 7200 7600 7800 7501
X √ √ √ √X X X X XX X X X XX X X X XX X X X √X X X X √X X X X XX X X X XX X X X √X X X X XX X X X XX X X X XX X X X √X X X X XX X X X XX X X X XX X X X X
X X X X √X X X XX X X X √³X X X X √³
NA 20 20 20 30NA NA NA NA 30
(1) Must use specified base (do not substitute with System Sensor branded bases)(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)
(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit with System Sensor 1151/1451 or System Sensor 2151/2451(5) MTB110RLP and MTB401BR both contain current limiting resistors and are for use with specified panels only(6) Each detection circuit must employ a single model number of smoke detector - DO NOT MIX TECHNOLOGIES and observe limit numbers.
3. Check total number of detectors on a circuit does not exceed the recommended maximum.4. In instances where there are NO detectors listed, the control panel must be changed and the entire fire alarm system verified.
√³
7502/7504 7516/7532 MIR1-1Z1 MIR1-2Z3/2Z6 FS-101
√ √ √ √ √⁴(30)X X X XX X X √ √⁴(30)X √ X X X√ √ X X X√ √ √ √ √⁴(25)X √ X X XX X X X X√ √ √ √ √⁴(30)X √ X √ XX X X X XX √ X X X√ √ √ √ √⁴(25)X X X X XX X X X XX X X X XX X X X X
√ √ √ √ √(42)
√³ √³ √³ √³ √³(42)√³ √³ √³ √³ √³(30)30 30 30 30 SPL⁴30 30 30 30 SPL⁴
(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)
√⁴(25)
√³ √³ √³ √³ √³(42)
FS-302 FS-502 FS-1004 M2000 MIR2 (GSA-UM)
√⁴(15) √⁴(15) √⁴(15) √ √√ X
√⁴(15) √⁴(15) √⁴(15) X √X X X X √X X X √ X
√⁴(12) √⁴(12) √⁴(12) √ √X X X X √X X X √ X
√⁴(15) √⁴(15) √⁴(15) X √X X X X √X X X √ XX X X √ X
√⁴(12) √⁴(12) √⁴(12) X √X X X X √X X X √ XX X X √ XX X X X X
√(21) √(21) √(21) √ √
√³(21) √³(21) √³(21) √³ √³√³(21) √³(21) √³(21) X √³SPL⁴ SPL⁴ SPL⁴ 30 30SPL⁴ SPL⁴ SPL⁴ 30 30
√⁴(12) √⁴(12) √⁴(12)
√³(21) √³(21) √³(21) √³ √³
790 (79045, 79045-2) 8000
√⁴ √X XX √X √X XX XX √X XX √X √X XX XX √X √X √X XX X
X √XX √³X √³
20 30NA 30
√³
Compatible Analog Loop DevicesMircom
MIX-1551AMIX-2551AMIX-1251A
MIX-2251A/2251TAMIX-2551TMA
MIX-7251AMIX-M500MAMIX-M501MA
MIX-1251BAMIX-2251BA
MIX-2251TMBAMIX-2251TBA
MIX-5251BAMIX-5251RBA
MIX-5251HAMIX-502MA
MIX-M500RAMIX-M500SA
MIX-M500DMASystem Sensor
5551A5551RA5251PA
5251RPAM500X
B524BIAB501B
IM-10ACR-6ASC-6A
FTX-P1AC2-6A
1251(B)2251/T
2551TM-R7251
M5251P/RPSmoke Detector Model NumberApollo
55000-22555000-325
HochikiDCD-135
DCD-135DCD-135DCD-190DCD-190DCD-190
SIJ-24SIJ-24SIJ-24
SLR-24SLR-24SLR-24
SLR-24HSLR-24HSLR-24HSLR-835SLR-835SLR-835
SLR-835B-2SLR-8354451HT
54515451
System Sensor14002400
1151A2151A
C2W-BAC2WT-BA
C2WTR-BA1451145124512451
1451DH2451-A
GE/Edwards6249C6250C6264C6266C6269C6270C
6269C-0036270C-003
Cerebrus Pyrotronics (Siemens)DI-2DI-3
Sentrol-ESL (GE)429C
429CT429CST429CRT
711U711U711U711U
713-5U713-5U713-5U713-5U
721U721U732U732U732U732U
Detection Systems Inc.DS250
DS250THDS282
DS282THMircom
MIR-525MIR-525T
MIR-1400AMIR-2400A
Mirtone7347173494735757349573495735957359573594734057359473405
C2M-PD1²
NapcoFW-2
Simplex/Grinnell (Tyco)2098-9110
FenwalPSD-7131PSD-7131PSD-7131PSD-7131PSD-7130PSD-7130PSD-7130PSD-7130PSD-7126PSD-7126PSD-7126PSD-7126PSD-7129PSD-7125PSD-7125PSD-7125PSD-7125CPD-7021CPD-7021CPD-7021CPD-7021
Max stand-by current of all detectors not to exceed 3mA
Legend: √ = CompatibleX = Not Compatible
Notes: (1) Must use specified base(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit with System Sensor 1151/1451 or System Sensor 2151/2451(5) Compatibility identifier for head/base assembly: 5500-225/45681-251, -255, -256, -258(6) Compatibility identifiers for head/base assemblies: A -A, HD-6, HD-3/HB-72, HB-3
Compatibility Issues: Maximum stand-by current of all detectors in an initiating circuit cannot exceed 3.0 milli-Amps.
Copyright © 2008 by Frank Kurz (All Rights Reserved)
Mircom Panel Model Number FX-2000 FA-300 FA-100
NA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X X
NA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X XNA √ X X
Base
NA √ √ √⁵NA √ √ √⁵
NS6-220 √ √ √⁶
NS4-220 √ √ √⁶HSC-220R √ √ √⁶NS6-220 √ √ √⁶NS4-220 √ √ √⁶
HSC-220R √ √ √⁶NS6-220 √ √ √⁶NS4-220 √ √ √⁶
HSC-220R √ √ √⁶NS6-220 √ √ √⁶NS4-220 √ √ √⁶
HSC-220R √ √ √⁶NS6-220 √ √ √⁶NS4-220 √ √ √⁶
HSC-220R √ √ √⁶NS6-220 √ √ √⁶NS4-220 √ √ √⁶
HSC-220R √ √ √⁶NA √ √ √⁶
NS6-220 X X √⁶B401 X X √⁶
B401B X X √⁶B401 X X √⁶
NA √ √ √NA √ √ √NA √ √ √NA √ √ √NA √ √ √NA √ √ √
X √ √B401B √ √ √B406B √ √ √B401B √ √ √B406B √ √ √
DH400A √ √ √DH400A √ √ √
NA √ √ √NA √ √ √NA √ √ √NA √ √ √NA √ √ √NA √ √ √NA √ √ √NA √ √ √
NA √ √ √
NA √ √ XDB-3S √ √ √
NA X X √NA X X √NA X X √NA X X √
701E X X √701U X X √702E X X √702U X X √701E X X √701U X X √702E X X √702U X X √702E X X √702U X X √701E X X √701U X X √702E X X √702U X X √
NA X X √NA X X √NA X X √NA X X √
NA √ √ √NA √ √ √NA √ √ √NA √ √ √
NA √ √ XNA √ √ XNA √ √ X
73486 √ √ X73487 √ √ X73486 √ √ X73497 √ √ X73400 √ √ X73400 √ √ X73401 √ √ X73401 √ √ X
NA √ √ √
√ √ X
70-201000-001 √ √ X70-201000-002 √ √ X70-201000-003 √ √ X70-201000-005 √ √ X70-201000-001 √ √ X70-201000-002 √ √ X70-201000-003 √ √ X70-201000-005 √ √ X70-201000-001 √ √ X70-201000-002 √ √ X70-201000-003 √ √ X70-201000-005 √ √ X70-201000-000 √ √ X70-201000-001 √ √ X70-201000-002 √ √ X70-201000-003 √ √ X70-201000-005 √ √ X70-201000-001 √ √ X70-201000-002 √ √ X70-201000-003 √ √ X70-201000-005 √ √ X
Max stand-by current of all detectors not to exceed 3mA
(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit with System Sensor 1151/1451 or System Sensor 2151/2451(5) Compatibility identifier for head/base assembly: 5500-225/45681-251, -255, -256, -258(6) Compatibility identifiers for head/base assemblies: A -A, HD-6, HD-3/HB-72, HB-3
Maximum stand-by current of all detectors in an initiating circuit cannot exceed 3.0 milli-Amps.
© 2008 by Frank Kurz (All Rights Reserved)
FA-200 FA-1000
X XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX X
X XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX X
√⁵ √⁵√⁵ √⁵
√⁶ √⁶
√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶√⁶ √⁶
√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √
√ √√ √√ √√ √√ √√ √√ √√ √
√ √
X X√ √
√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √√ √
√ √√ √√ √√ √
√ √√ √√ √√ √
X XX XX XX XX XX XX XX XX XX XX X
√ √
X X
X XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX X
(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)
Compatible Analog Loop DevicesSystem Sensor
2W-BA5551RA5251PA
5251RPAM500X
B524BIAB501B
IM-10ACR-6ASC-6A
FTX-P1AC2-6A
1251(B)2251/T
2551TM-R7251
M5251P/RPSmoke Detector Model NumberApollo
55000-22555000-325
HochikiDCD-135DCD-135DCD-135DCD-190DCD-190DCD-190
SIJ-24SIJ-24SIJ-24
SLR-24SLR-24SLR-24
SLR-24HSLR-24HSLR-24HSLR-835SLR-835SLR-835
SLR-835B-2SLR-8354451HT
54515451
System Sensor
14002400
1151A2151A
C2W-BAC2WT-BA
C2WTR-BA1451145124512451
1451DH2451-A
GE/Edwards6249C6250C6264C6266C6269C6270C
6269C-0036270C-003
C2M-PD1Cerebrus Pyrotronics (Siemens)
DI-2DI-3
Sentrol-ESL (GE)429C
429CT429CST429CRT
711U711U711U711U
713-5U713-5U713-5U713-5U
721U721U732U732U732U732U
Detection Systems Inc.DS250
DS250TH
DS282DS282TH
MircomMIR-525
MIR-525TMIR-1400AMIR-2400A
Mirtone7347173494735757349573495735957359573594734057359473405
NapcoFW-2
Simplex/Grinnell (Tyco)2098-9110
FenwalPSD-7131PSD-7131PSD-7131PSD-7131PSD-7130PSD-7130PSD-7130PSD-7130PSD-7126PSD-7126PSD-7126PSD-7126PSD-7129PSD-7125PSD-7125PSD-7125PSD-7125CPD-7021CPD-7021CPD-7021CPD-7021
Max stand-by current of all detectors not to exceed 3mA
Legend: √ = CompatibleX = Not Compatible
Notes: (1) Must use specified base(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit with System Sensor 1151/1451 or System Sensor 2151/2451(5) Compatibility identifier for head/base assembly: 5500-225/45681-251, -255, -256, -258(6) Compatibility identifiers for head/base assemblies: A -A, HD-6, HD-3/HB-72, HB-3
Compatibility Issues: Maximum stand-by current of all detectors in an initiating circuit cannot exceed 3.0 milli-Amps.
Copyright © 2008 by Frank Kurz (All Rights Reserved)
Notifier Panel Models AFP-200 AFP-300/400
NA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ XNA √ X
Base
NA √ √NA √ √
NS6-220 √ √NS4-220 √ √
HSC-220R √ √NS6-220 √ √NS4-220 √ √
HSC-220R √ √NS6-220 √ √NS4-220 √ √
HSC-220R √ √NS6-220 √ √NS4-220 √ √
HSC-220R √ √NS6-220 √ √NS4-220 √ √
HSC-220R √ √NS6-220 √ √NS4-220 √ √
HSC-220R √ √NA √ √
NS6-220 X XB401 X X
B401B X XB401 X X
NA √ √NA √ √NA √ √NA √ √NA √ √NA √ √
X √B401B √ √B406B √ √B401B √ √B406B √ √
DH400A √ √DH400A √ √
NA X XNA √ √NA √ √NA √ √NA √ √NA √ √NA √ √NA √ √NA √ √
NA √ √DB-3S √ √
NA X XNA X XNA X XNA X X
701E X X701U X X702E X X702U X X701E X X701U X X702E X X702U X X702E X X702U X X701E X X701U X X702E X X702U X X
NA X XNA X X
NA X XNA X X
NA √ √NA √ √NA √ √NA √ √
NA √ √NA √ √NA √ √
73486 √ √73487 √ √73486 √ √73497 √ √73400 √ √73400 √ √73401 √ √73401 √ √
NA √ √
√ √
70-201000-001 √ √70-201000-002 √ √70-201000-003 √ √70-201000-005 √ √70-201000-001 √ √70-201000-002 √ √70-201000-003 √ √70-201000-005 √ √70-201000-001 √ √70-201000-002 √ √70-201000-003 √ √70-201000-005 √ √70-201000-000 √ √70-201000-001 √ √70-201000-002 √ √70-201000-003 √ √70-201000-005 √ √70-201000-001 √ √70-201000-002 √ √70-201000-003 √ √70-201000-005 √ √
Max stand-by current of all detectors not to exceed 3mA
(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)(3) Compatible only with "Clean Me" option "OFF"(4) Do NOT mix model 1400 and 2400 smoke detectors on the same circuit with System Sensor 1151/1451 or System Sensor 2151/2451(5) Compatibility identifier for head/base assembly: 5500-225/45681-251, -255, -256, -258(6) Compatibility identifiers for head/base assemblies: A -A, HD-6, HD-3/HB-72, HB-3
Maximum stand-by current of all detectors in an initiating circuit cannot exceed 3.0 milli-Amps.
© 2008 by Frank Kurz (All Rights Reserved)
AFC-600/NFS-640 NFS2-640 NFS-320
X X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X X
√⁵ √⁵ √⁵√⁵ √⁵ √⁵
√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶√⁶ √⁶ √⁶
√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √
X X X√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √
X X X√ √ √
√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √√ √ √
√ √ √√ √ √
√ √ √√ √ √
√ √ √√ √ √√ √ √√ √ √
X X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X X
√ √ √
X X X
X X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X XX X X
(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)
NFS-3030 AM2020/AFP-1010 RP-1001 RP-1002
(2) CM2M-PD1 is a direct replacement for Edwards Models 6249C & 6251C and may be used on all panels where these detectors were cross-listed (CM2M-PDC has "Clean Me" technology and may NOT function with some panel models)
S500(TC-2/TC-4) S5000 (TCM-2/TCM-4) XP5-C FCM-1
Recommended