View
3
Download
0
Category
Preview:
Citation preview
1 of 8888-60-041-01 rev.D • 9/04
A B
1
2
User's Guide
USA 1-800-888-8458Europe +31 20 312.29.39
6X
M4 x 10mm
10-24 x 1/2"
4X
1/8"
FX75 Monitor MountInterface BracketMIS-E VESA Compliant
A anchor bracket
1 Separate the brackets (if joined together) by moving the release lever to the left.
B display bracket
2 of 8888-60-041-01 rev.D • 9/04
5
Option ADirect to Vertical Surface 2
2 Mount FX75 anchor bracket
Option BErgotron Mounting Solution 4
Option AMount Direct to Vertical Surface
a Use anchor bracket as template to mark holes.Draw center line with level.
NOTE: Consult display manufacturer for mounting location recommendations.
3 of 8888-60-041-01 rev.D • 9/04
Three-hole Mounting NOTE: Fasten-ers are supplied by customer. Consult a
qualifi ed engineering, architectural or con-
struction professional to determine the
appropriate mounting fasteners and holes
based on your display specifi cations and
application.
Because vertical surfaces vary widely and the ultimate mounting method is out of Ergotron's control, it is imperative that you consult with appropriate engineering, architectural or construction personnel to ensure that the FX75 is mounted properly to handle applied loads.
Four-hole Mounting NOTE: Fasten-ers are supplied by customer. Consult a
qualifi ed engineering, architectural or con-
struction professional to determine the
appropriate mounting fasteners and holes
based on your display specifi cations and
application.
Seven-hole Mounting NOTE: Fasten-ers are supplied by customer. Consult a
qualifi ed engineering, architectural or con-
struction professional to determine the
appropriate mounting fasteners and holes
based on your display specifi cations and
application.
b Mount anchor bracket to vertical surface.
63 Mount FX75 display bracket
4 of 8888-60-041-01 rev.D • 9/04
1½" Diameter Pole Mount Bracket
2" or 3" Command Post Mount Brackets
2" Diameter Pole Mount Brackets
Fasteners supplied with FX75
10-24 x 1/2"
4X
10-24 x 3/8"4X
Fasteners supplied with Command Post Bracket
Fasteners supplied with FX75
10-24 x 1/2"
4X
Option BErgotron Mounting Solution (ordered separately)
63 Mount FX75 display bracket
Before mounting the FX75, ensure that the pole command post or wall trackis secure and can support the applied load.
5 of 8888-60-041-01 rev.D • 9/04
Wall Track
Fasteners supplied with Wall Track Brackets
3/8-16 x 5/8"
4X
Before mounting the FX75, ensure that the pole command post or wall trackis secure and can support the applied load.
1/4-20 x 3/4"
1/4-20 x 1/2"
1X
1X
a
b c
Option BErgotron Mounting Solution (ordered separately)
63 Mount FX75 display bracket
6 of 8888-60-041-01 rev.D • 9/04
6X
M4 x 10mm
100mm x 200mmMIS-E, C VESA Compliant*
3 Attach FX75 display bracket to display
? mm
? mmErgotron USA 1-800-383-1916Ergotron Europe +31 20 312.29.39
* NOTE: If your display does not have the VESA compliant100mm x 200mm hole pattern,contact your Ergotron representative.
a If applicable, remove existing base according to displaymanufacturer's instructions.
b Place display on a fl at, stable surface over a protective cover-ing to avoid possible damage to the screen while mounting bracket.
c Attach bracket to display using provided fasteners.
7 of 8888-60-041-01 rev.D • 9/04
!
4 Mount display (join display bracket and anchor bracket)
To ensure secure attachment of display, brackets must engage.*
Align and slide display
bracket tabs down
into anchor bracket
slots.
Swing bottom
of display back until
the display bracket
knobs push into the anchor
bracket holes.
NOTE: You'll hear
a clicking sound when
brackets engage.*
b
CAUTION: This step may require two people dependingon dimensions and weight of your display.
c d
a Lower display bracket (attached to display) over anchor bracket.
8 of 8888-60-041-01 rev.D • 9/04
© 2004 Ergotron, Inc. All rights reserved.
Patents Pending and Patented U.S. & Foreign. Ergotron is a registered trademark of Ergotron, Inc. Reproduction of this material in whole or part for any purpose other than that authorized by Ergotron, Inc. is prohibited.
a With the display securely supported, slide the release lever to the right with a slotted screwdriver . . .
b . . . tilt bottom of display forward . . .
5 Removing the display
CAUTION: This step may require two people dependingon dimensions and weight of your display.
c . . . and lift up.
b
c
!
Recommended