VIDEO AMPLIFIERS & SPLITTERS

132

BAND SEPARATORS, SPLITTERS....perfectly designed and matched for TV and FM signalscoming from the UHF-VHF-FM BANDS. Heavy duty wire andcable prevents broken connections. Non-strip piercingscrews are made of plated brass for corrosion-free reliability.Add suffix letter “B” to part number for bulk pack.

No. MT7775-300 OHM BALUN

WITH UHF/VHF/FM SPLITTERMatches impedance between 75ohm coaxial cable and 300 ohmTV and FM antenna inputs. It sep-arates the three signals from the3-way antenna into individual sig-nals for UHF, VHF and FM. Twooutputs connect to the UHF, VHFantenna terminals on rear of the TV set. Separate screw terminalconnects 300 ohm twin lead to the FM receivers. For VCR’s too.

No. MT7875-300 OHM BALUN AND

UHF/VHF/FM BAND SEPARATORSeparates incoming signals froma 75 ohm antenna downlead intoUHF, VHF and FM bands. Thecoaxial 75 ohm cable is fittedwith an “F” connector to accom-modate the VHF terminal on rearof TV set or VCR. The 300 ohm output for UHF connects to thereceiver with heavy, hook terminated wires.

No. MT8875 ohm VHF + 300ohm UHF to 75 ohm push-on male.

No. CA280

300 OHM JUMPER CABLE300 ohm cable, twin lead, with spade lug on both ends for extension leadbetween VCR and TV, 6ft.

SEPARATOR/COMBINER BALUNSDesigned expressly for TV sets with “F” coaxial jack input, these baluns will accept75 ohm coax or 300 ohm twin lead input and combine them, feeding them to theset through a push-on “F” connector on the back of each type. These combinersmay be used as separators because they can function with signal fed in eitherdirection. Individually packaged for display rack, they may be obtained bulkpacked by adding suffix letter “B” to the part number.

(Back View)

No. MT8675 ohm VHF + 75 ohmUHF to 75 ohm push-on male.

No. MT87300 ohm VHF + 300 ohmUHF to 75 ohm push-on male.

VIDEO AMPLIFIERS & SPLITTERS

UHF/VHF/FM HIGH GAIN DISTRIBU-TION AMPLIFIER (with FM TRAP)

No. DA27BTraps out strong FM interference from TV.

SPECIFICATIONS:Band Width: 50 to 400 Mhz. 470 to 890 Mhz.Output Capability: 40 dbmVGain: 25db 23dbNoise Figure: 3.5 db 7.5 dbFM Trap Attenuation: -20 db (switchable) 95 - 108 MHz.Input: 75 ohm, “F” type coax connectorOutput: 75 ohm, “F” type coax connectorPower Source: 120VAC 60HzDimensions: 3-3/32” x 6-5/8” x 1-7/16”

10 db VCR/TV SIGNAL AMPLIFIER50-900MHz

6 db VCR/TV SIGNAL AMPLIFIERwith 2 OUTPUTS 50-900MHz

10 db VCR/TV SIGNAL AMPLIFIERwith 4 OUTPUTS 50-900MHz

Sharpens and improves pic-ture quality by restoring signalloss that occurs in some 75ohm connections. Standard“F” connectors; 117 volt @1.2 watt operation. Boostsboth TV and FM radio sys-tems. No. DA10B

Single 75 ohm input fromantenna or cable systemwith two 75 ohm outputs.Standard “F” connectors;117 volt @ 1.2 watt (10mA)operation.No. DA12B

Single 75 ohm input fromantenna or cable systemwith four 75 ohm outputs.Standard “F” connectors;117 volt @ 1.2 watt (10mA)operation.No. DA14B

*ALL PHILMORE Signal Amplifiers cover to 900 MHz and can beused to amplify cable signal.