Upload
rajneesh-kumar
View
518
Download
0
Embed Size (px)
Citation preview
05/02/2023 Electrochemical Mechaning 1
ELECTRO CHEMICAL MACHINING
SUBMITTED BY:Rajneesh Kumar
05/02/2023 Electrochemical Mechaning 2
CONTENT: Non-Traditional Machining
Classification of Non-traditional Machining Processes Electrochemical Machining (ECM)
What is Electroplating? Electrochemical Machining History
Tool Material Schematic diagram
05/02/2023 Electrochemical Mechaning 3
Non-Traditional Machining
Need :
• To machine newly developed metals and non-metals
• To machine complex part geometries
• To avoid surface damage
05/02/2023 Electrochemical Mechaning 4
Classification of Non-traditional Machining Processes
This classification is carried out depending on nature of energy used for material removal:
Mechanical Thermo- Chemical
Electro electricElectrochemical
• USM• AJM•WJM• AWJM
• EDM• EBM• LBM• PAM
• CHM• PCM
• ECG• EJD• ECM
05/02/2023 Electrochemical Mechaning 5
Electrochemical Machining (ECM)
• Electrochemical machining (ECM) is an electrolytic material removal process involving a negatively charged shaped electrode (cathode), a conductive fluid (electrolyte), and a conductive work piece (anode).
• ECM is characterized as "reverse electroplating." The tool must be properly shaped, and provision for waste removal must be made.
05/02/2023 Electrochemical Mechaning 6
What is Electroplating?
An electrochemical process where metal ions are transferred from a solution and are deposited as a thin layer onto surface of a cathode.
The setup is composed DC circuit with an anode and a cathode sitting in a bath of solution that has the metal ions necessary for coating or plating
Electroplating can enhance;Chemical properties---increase corrosion resistancePhysical properties---increase thickness of partMechanical properties---increase tensile strength & hardness
05/02/2023 7
How it works
Copper Cathode is reduced(accepts electrons)
Nickel Anode is oxidized(gives us electrons)
Ni2+ ions within solution become attracted to Copper cathode
Electrochemical Machining
05/02/2023 Electrochemical Mechaning 8
Electrochemical Machining History
• Electrochemical machining (ECM) has been developed initially to machine these hard to machine alloys, although any metal can so be machined.
• ECM is an electrolytic process and its basis is the phenomenon of electrolysis, whose laws were established by Faraday in 1833.
• The first significant developments occurred in the
1950s, when ECM was investigated as a method for shaping high strength alloys.
• As of the 1990s, ECM is employed in many ways, for example, by automotive, offshore petroleum, and medical engineering industries, as well as by aerospace firms, which are its principal user.
05/02/2023 Electrochemical Mechaning 9
Working Principle
05/02/2023 Electrochemical Mechaning 10
Tool Material
•The tool is typically made of• copper,• brass, or •stainless steel, •while the most commonly used electrolyte is a concentrated solution of inorganic salts, such as sodium chloride, and the direct current power source is low voltage and high ampere.
05/02/2023 Electrochemical Mechaning 11
Schematic diagram
05/02/2023 Electrochemical Mechaning 12
ECM Components (Power)•The power needed to operate the ECM is obviously electrical. There are many specifications to this power.
•The current density must be high.
•The gap between the tool and the work piece must be low for higher accuracy, thus the voltage must be low to avoid a short circuit. •The control system uses some of this electrical power.
05/02/2023 Electrochemical Mechaning 13
ECM Components (electrolyte circulation system)
•The electrolyte must be injected in the gap at high speed (between 1500 to 3000 m/min).
•The inlet pressure must be between 0.15-3 MPa.
•The electrolyte system must include a fairly strong pump.
•System also includes a filter, sludge removal system, and treatment units.
•The electrolyte is stored in a tank.
05/02/2023 Electrochemical Mechaning 14
ECM Components (control system)• Control parameters include:
VoltageInlet and outlet pressure of electrolyteTemperature of electrolyte.
• The current is dependent on the above parameters and the feed rate.
05/02/2023 Electrochemical Mechaning 15
Advantage• Components are not subject to either thermal or
mechanical stress. There is no tool wear in ECM.
• Non-rigid and open work pieces can be machined easily as there is no contact between the tool and work piece.
• Complex geometrical shapes can be machined repeatedly and accurately
• ECM is a time saving process when compared with conventional machining
• During drilling, deep holes can be made or several holes at once.
Surface finishes of 25 µ (micron) can be achieved in ECM.
05/02/2023 Electrochemical Mechaning 16
Disadvantage• More expensive than conventional machining.
• Need more area for installation.
• Electrolytes may destroy the equipment.
• Not environmentally friendly (sludge and other waste)
• High energy consumption.
• Material has to be electrically conductive.
05/02/2023 Electrochemical Mechaning 17
Applications
• Die-sinking operations
• Drilling jet engine turbine blades
• Multiple hole drilling
• Machining steam turbine blades within close limits
• jet engines
05/02/2023 Electrochemical Mechaning 18
Products• The two most common products of ECM are turbine/compressor blades
and rifle barrels. Each of those parts require machining of extremely hard metals with certain mechanical specifications that would be really difficult to perform on conventional machines.
• Some of these mechanical characteristics achieved by ECM are:
Stress free grooves. Any groove geometry. Any conductive metal can be machined. Repeatable accuracy of 0.005”. High surface finish. Fast cycle time.
05/02/2023 Electrochemical Mechaning 19