9011041155 / 9011031155

Current Electricity Exercises 1. State and explain Kirchhoff’s law for electrical circuit.Ans: Kirchhoff’s first law or current law (or) junction law :

The algebraic sum of electric currents at any junction is always equal to zero i.e. ∑I = 0.Sign Conventions :1. Current entering the junction in the circuit are taken positive.2. Current leaving the junction are taken negative,Explanation :Let O be a point at a junction in an electric circuit. Let I1, I2, I3, I4 be the current flowing through them as shown in the above figure.According to Kirchhoff’s first law,I1 + I2 + I3 + I4 = 0 or I1 + I2 + I4 = I3In other words, the total current flowing towards a junction is equal to the total current flowing away from the junction. This law is based on the law of conservation of charges.Kirchhoff’s Second Law :In a closed loop of electrical network, the algebraic sum of potential differences for all components plus the algebraic sum of all emfs is equal to zero.∑E + ∑IR = 0Sign Conventions :For e.m.f. :1. If we traverse from lower plotential to higher potential (i.e. from negative

terminal to positive terminal), then emf is treated as positive.

From A to B, emf is positive.2. If we traverse from higher potential to lower potential (i.e. from positive

terminal to negative terminal), then emf is trated as negative.From B to A, emf is negative.

For Potential Difference :1. If we traverse along the direction of current then potential

difference across the resistance is treated as negative.From A to B potential difference is -- IR.

2. If we traverse opposite to the direction of current then potential difference across the resistance is treated as positive.From B to A potential difference is + IR.Explanation :Applying voltage law to the loop ABCDA,R(I1 + I2) - I1R4 - I1R1 - E = 0 …(1)

1

9011041155 / 9011031155

Applying voltage law to the loop ABEFA,R(I1 + I2) - I1R4 - I1R1 - E = 0 …(1)Solving equations (1) and (2), we get the required currents.

2. Obtain balancing condition in case of Wheatstone’s network.Ans: A simple circuit devised by Wheatstone for determining unknown resistance is

called Wheatstone’s network.It consists of four resistances R1, R2, R3 and R4 along the four arms of a quadrilateral ABCD.A cell E, key K and rheostat are connected between A and C in series. A galvanometer is connected between B and D.Resistances R1, R2, R3 and R4 are selected such that potential at B is equal to potential at D. The galvanometer gives zero deflection and the network is said to be balanced.To derive the condition for balanced bridge.Applying Kirchhoff’s voltage law to loop ABDA,-I1R1 - IgG + I2R3 = 0 For a balanced bridge, Ig = 0.Q Ig = 0∴ -I1R1 = -I2R3∴ I1R1 = I2R3 …(1)Applying Kirchhoff’s voltage law to loop BCDB,∴ -I1R2 + I2R4 + IgG = 0For a balanced bridge, Ig = 0.O Ig = 0∴ -I1R2 = -I2R4

∴ I1R2 = I2R4 …(2)Dividing equation (1) by equation (2),

If any three resistance are known, we can determine the fourth resistance. This is called balancing condition.

3. Explain with neat circuit diagram, how will you determine the unknown resistance by using a meter-bridge.

Ans: Meter bridge is a Wheatstone’s network used to determine unknown resistance.

It works on the principle of balanced Wheatstone’s network, i.e. Construction :i. It consists of a thin, uniform homogenous conducting wire of one meter

2

9011041155 / 9011031155

length which is stretched on a rectangular wooden board between two points A and C. At A and C, there are two L-shaped copper strips C1 and C2. Between C1 and C2, there is a third copper strip C3. A meter scale is fixed below the wire to measure the balancing length. Two gaps are formed between C1, C2 and C3.Between A and C, a battery E, single-way key K and rheostat Rh are connected in series. Between B and D, a galvanometer is connected.In one gap, unknown resistance X and in the other gap, known resistance (resistance box) R is connected.AC = long 1m uniform, thin and homogenous wire,X = unknown resistance,R = resistance box (known resistance)G = galvanometer,C1, C2 and C3 = copper strips,K = single-way key, E = battery, Rh = rheostat.

1. When the key K is closed, the current starts flowing through the circuit. The current can be controlled by rheostat Rh.2. The jockey is touched at difference points of the wire and a point on the

wire is

4. Describe Kelvin’s method to determine the resistance of galvanometer by using meter-bridge.

Ans:

1. A galvanometer whose resistance is to be determined is connected in left gap and a resistance box (known resistance R) is connected in right gap.

2. A battery E, single-way key Kand rheostat are connected in series between A and C. Junction B of the galvanometer and the resistance box is connected to the jockey.

3

9011041155 / 9011031155

3. A suitable resistance R is taken in the resistance box and current I is introduced in the circuit by closing key K. Without touching the jockey to any point of the wire, the deflection in the galvanometer is noted.

4. Touch the jockey at different points of the wire between A and C and find a point D at which the galvanometer gives same deflection as before. In this method, null deflection is not obtained. The deflection of the galvanometer should be equal in both the cases whether the jockey is touched to the wire or without touching.

5. Let the length of wire AD = ℓg and length of wire CD =ℓR.

According to balanced Wheatstone’s network condition,

…(i)

6. Let the resistance per unit length of the wire be σ.

∴ Resistance of wire AD = σ ℓg

Resistance of wire CD = σ ℓR

7. Putting these values in equation (i),

ℓR = 100 - ℓg

Resistance of the galvanometer G can be determined knowing the values of R and Ig.

5. State any two sources of errors in meter-bridge experiment. Explain how they can be minimized.

Ans:1. If the wire is not uniform, the resistance per unit length will not be same

everywhere. So, there will be an error in the value of unknown resistance.

2. The points where the wire is joined to the copper strips, the contact resistance is developed which produces an error in the value of unknown resistance X.

4

9011041155 / 9011031155

Minimization of errors :

1. The wire must be uniform and should have same cross-sectional area

throughout the length.

2. The value of resistance from the resistance box should be chosen such that the null point is near the centre of the wire, i.e. between 35 cm and 65 cm.

3. The experiment should be repeated by interchanging the resistance in left and right gaps.

4. The ends of the wire must coincide with 0 and 100 cm mark on the meter scale.

6. Explain : In Wheatstone’s meter-bridge experiment the null point is obtained in middle one third portion of wire.

Ans:

1. If the wire of meter bridge is not uniform the value of resistance per unit length may not be same and error is introduced.

2. The error is introduced due to contact resistances developed at the points of contact where wire is connected to the copper strips.

To minimize these errors, the null point is obtained in middle one-third of the wire.

7. Explain the principle of potentiometer.Ans:

Let AB be potentiometer wire of length L, resistance R.A battery of e.m.f. E is connected across the wire. Let the potential difference across AB be VAB.

5

9011041155 / 9011031155

Let resistance per unit length of wire be σ.

∴ R = σ L …(i)

The current flowing through the potentiometer wire :

…(ii)

Let there be a point P on the wire. The length of the wire between A and P is ℓ. Potential difference across A and P :

VAP = Ir (r is the resistance of length AP of wire)

r = σ1

∴ VAP = I σ1

Putting the value of I from equation (ii),

VAB and L are constant.

∴ VAP ∝ 1

Thus, the potential difference between any two points of the potentiometer wire is directly proportional to the length of the wire between the two points. This is the principle of potentiometer.

8. Describe how potentiometer is used to compare the e.m.f.s of two cells by (a) direct method (b) combination method.

Ans:

6

9011041155 / 9011031155

Connect the circuit according to the circuit diagram. Close the key K to pass the current through potentiometer wire. A potential gradient is developed across the wire.

When K1 and K3 are closed, the cells E1 and E2 assist each other. When K2 and K4

are closed, E1 and E2 oppose each other.

Cells assisting each other :

Effective e.m.f. = E1 + E2

Cells opposing each other :

Effective e.m.f. = E1 – E2

Close the keys K1 and K3 and touch the jockey at different points of the wire to obtain null deflection. Let the balancing length AP = L1.

E1 + E2 =I σ L1 …(i)

σ = resistance per unit length of wire

Close the keys K2 and K4 and find the balancing length AP’=L2.

E1 – E2 = I σ L2 …(ii)

Dividing equation (i) and equation (ii),

7

9011041155 / 9011031155

Using componendo and dividendo,

Knowing L1 and L2, the e.m.f.s of two cells can be compared.

9. Describe with the help of a neat circuit diagram how will you determine the internal resistance of a cell by using potentiometer. Derive the necessary formula.Ans: The potentiometer wire is connected in series with battery of e.m.f. E, key K and

rheostat Rh in order to establish a current in the circuit so that a potential gradient is developed across the wire.

Positive terminal of E1 is connected at A and negative terminal is connected to galvanometer and then to the jockey.

A resistance box (R) in series with key K1 is connected in parallel with the cell of E1 whose internal resistance is to be determined.

Connect the circuit as per the circuit diagram. Close the key K to establish current and potential gradient along the wire. Keep the key K1 open and touch the jockey at different points of the potentiometer wire and find a point at which galvanometer shows null deflection. Let the balancing length AP = ℓ1.

∵ no current is flowing through the cell,

8

9011041155 / 9011031155

∴ E1 = I σ I1

Close key K1 and take some suitable resistance from resistance box. Find the balancing length AP’ = ℓ2.

∵ the current is flowing through the cell, through R, so terminal potential difference of the cell balances the potential difference across length ℓ2.

V = I σ I2 …(ii)

Divide equation (i) by (ii)

…(iii)

Let the internal resistance of cell be r.

∴ Current through

∴ Terminal potential difference V = IR.

…(iv)

From equations (iii) and (iv),

∴ Rℓ2 + rℓ2 = Rℓ1

∴ rℓ2 = Rℓ1 - Rℓ2 = R (ℓ1 - ℓ2)

…(v)

Using equation (v), knowing the value of R, ℓ1 and ℓ2, the internal resistance of cell (r) can be determined.

9

9011041155 / 9011031155

10. State the precautions which must be taken while performing experiment with potentiometer.

Ans: Precautions to be taken :

1. The wire used must be uniform i.e. of same cross section.

2. The value of ‘R’ should be so chosen that the null point is obtained as near(close) to the centre of wire as possible. (Middle one-third of wire i.e. between 33.33 cm and 66.67 cm)

3. The experiment should be repeated by interchanging the positions of X and R to minimize an error due to contact resistance.

11. State the advantages of potentiometer over voltmeter.Ans:

Advantages of potentiometer :

1. The voltmeter is used only to measure the terminal potential difference whereas the potentiometer measures the small potential difference and the e.m.f. of the cell.

2. Accuracy of potentiometer can be increased by increasing its length. The accuracy of voltmeter cannot be increased beyond a certain limit.

3. Internal resistance of cell can be measured with potentiometer but it cannot be measured with voltmeter.

4. A small potential difference can be measured accurately with the help of potentiometer. The resistance of voltmeter is not infinity to work as an ideal voltmeter.

10

9011041155 / 9011031155

Problem for Practice1. A cell of e.m.f. 3V and internal resistance 4Ω is connected to two resistances

10Ω and 24Ω joined in parallel. Find the current through each resistance using Kirchhoff’s laws.

Ans: Given : E = 3V, r = 4Ω, R1 = 10Ω, R2 = 24 ΩTo find : I1 = ?, I2 = ?Let I1 and I2 be the currents through the resistor R1 and R2 respectively. I be the current drawn from the cell.At junction B, applying Kirchhoff’s law we getI - I1 - I2 = 0 or I = I1 + I2 …(I)Applying Kirchhoff’s voltage law to loop ABCDEFA, we get,-I1R1 - Ir + E = 0-10(I1) - 4 (I1 + I2) + 3 = 0-10I1 - 4I1 - 4I2 = -3-14I1 - 4I2 = -314I1 + 4I2 = 3 …(II)Applying Kirchhoff’s voltage law to loop BDECB, we get, -I2R2 + I1 + R1 = 0-24I2 + 10I1 = 0- 24I2 = -10I1 24I2 = 10I1∴ I1 = 2.4I2 …(III)Substituting eq. (III) in eq. (II), we get14(2.4I2) + 4I2 = 337.6I2 = 3

∴ I2 = 0.0798 ASubstituting eq. (IV) in eq. (III), we getI1 = 2.4 × 0.0798 = 0.1915 AThus, I = I1 + I2 = 0.1915 + 0.0798 = 0.2713A

11

9011041155 / 9011031155

2. The current flowing through an external resistance of 2Ω is 0.5 A when it is connected to the terminals of a cell. This current reduces to 0.25 A when the external resistance is 5Ω. Use Kirchhoff’s laws to find e.m.f. of cell.

Ans: Given : R = 2Ω, I = 0.5A : Ist caseR = 5Ω, I = 0.25 A : IInd caseTo find : E = ?Let I be the current, r and E be the internal resistance and emf of the cell. R be the external resistance.According to Kirchhoff’s voltage law :E = I (R + r) = 0 i.e. E = I (R + r)In first case,E = 0.5 (2 + r)In second case,E = 0.25 (5 + r)From equation I and II, we get0.5 (2 + r) = 0.25 (5 + r)∴ 2(2 + r) = (5 + r)∴ 4 + 2r = 5 + r∴ r = 1ΩSubstituting r in eq. (1) we getE = 0.5 (2 + 1) = 0.5 (3)∴ E = 1.5V

3. Four resistances 5Ω, 10Ω, 15Ω and an unknown XΩ are connected in series so as to form Wheatstone’s network. Determine the unknown resistance X, if the network is balanced with these numerical values of resistances.

Ans: Given :R1 = 5Ω, R2 = 10Ω, R4 = 15Ω, R3 = XTo find : Unknown resistance R3 = X = ?Since the network is balanced.

∴ X = 7.5Ω4. In a meter-bridge experiment with resistance R1 in left gap and

resistance X in right gap, null point is obtained at 40 cm from left end. With a resistance R2 in left gap and same resistance X in right gap, null point is obtained at 50 cm from left end. Where will be null point if R1

and R2 are put first in series and then in parallel, in the left gap and right gap still containing X?

Ans: Given : I case : ℓX = 40cm, ℓR = 60cmII case : ℓX = 50cm, ℓR = 50cmTo find : ℓ1 = ? when R1 and R2 are in series ℓ2 = ? when R1 and R2 are in parallel

12

9011041155 / 9011031155

,

II case : i. When R1 and R2 are connected in series the effective resistance is

Let the corresponding null point be at a distance from ℓ1 from the left end of the wire.

∴ 500 - 5ℓ1 = 3ℓ1 ∴ 500 = 8ℓ1

ii. When R1 and R2 are connected in parallel the effective resistance is

Let the corresponding null point be at a distance ℓ2 from the left end of the wire.

∴ 200 - 2ℓ2 = 42 ∴ 200 = 7ℓ2

5. A potentiometer wire has a length of 2m and resistance 10Ω. It is connected in series with resistance 990Ω and a cell of e.m.f. 2V. Calculate the potential gradient along the wire.

Ans: We have L = 10m, r = 10Ω, R = 990 Ω, E = 2V Let,

The potential difference across the wire is But, V = Ir = 2 × 10-3 × 10 = 2 × 10-2 V

13

9011041155 / 9011031155

∴ Potential gradient along the wire

6. Two cells having unknown e.m.f.s E1 and E2 (E1 > E2) are connected in potentiometer circuit so as to assist each other. The null point is obtained at 8.125 m from the higher potential end. When cell E2 is connected so as to oppose cell E1, the null point is obtained at 1.25m from same end. Compare the e.m.f.s of two cells.

Ans:ℓ1 = 8.125 m (cells assisting), ℓ2 = 1.25 m (cells opposing) E1 + E2 = kℓ1 and E1 – E2 = k ℓ2 Where k is the potential gradient.

7. A potentiometer wire has a length 10m and a resistance 20Ω. Its terminals are connected to a battery of e.m.f. 4V and internal resistance 5Ω. What are the distances at which null points are obtained when two cells of e.m.f.s 1.5V and 1.3 V are connected so as to (a) assist and (b) oppose each other?

Ans: L = 10m, r = 20Ω, E = 4 V, , E1 = 1.5 V, E2 = 1.3 VPotential gradient,

When the cells assist each other, the resultant emf = E1 + E2. Let ℓ1 be the balancing length. ∴ E1 + E2 = kℓ1

14

9011041155 / 9011031155

When the cells oppose each other, the resultant emf = E1 – E2. Let ℓ2 be the balancing length. ∴ E1 – E2 = kℓ2

For the two cells once assisting and once opposing each other, the null points will be obtained at 8.75 m and 0.625 m, respectively, from the high potential end.

8. A potentiometer wire of length 4m and resistance 8Ω is connected in series with a battery of e.m.f. 2V and negligible internal resistance. If the e.m.f. of cell balances against length of 217 cm of the wire, find the e.m.f. of cell. When a cell is shunted by a resistance of 15Ω, the balancing length is reduced by 17 cm. Find the internal resistance of a cell.

Ans: L = 4m, r = 8Ω, E = 2 V, rc = 0, R = 15 Ω, ℓ = 217 cm = 2.17 m, ℓ1 = 217 – 17 = 200 cm = 2m Potential gradient,

If the emf of the cell is E1, E1 = kℓ = 0.5 × 2.17 = 1.085 V The internal resistance of the cell is

9. A voltmeter has a resistance of 100Ω. What will be its reading when it is connected across a cell of e.m.f. 2V and internal resistance 20Ω?

Ans: Given : RV = 100Ω, E = 2V, r = 20ΩTo find : Voltmeter reading = ?Let I be the current drawn from the cell.Applying Kirchhoff’s voltage law we getE - IRV - Ir = 0I (RV + r) = E

The voltmeter measures the terminal potential difference of the cell.

15

9011041155 / 9011031155

10. Four resistances 4, 4, 4 and 12Ω form a Wheatstone’s network. Find the resistance which when connected across the 12Ω resistance, will balance the network.

Ans: Given :R1 = 4Ω, R2 = 4Ω, R3 = 4Ω, R4 = 12 ΩTo find : R connected parallel to R4 = ?To balance the network, the resistance in the fourth arm must also be 4Ω. Hence, the resistance (R) to be connected across the 12Ω resistance should be such that their equivalent resistance is 4Ω.

11. Two resistances X and Y in the two gaps of a meter-bridge give a null point dividing the wire in the ratio 2:3. If each resistance is increased by 30Ω, the null point divides the wire in the ratio 5:6, calculate each resistance,

Ans:From the data, we have in the first case,

and in the second case, ∴ 6 X + 180 = 5Y + 150 ∴ 2 (3X) = 5 Y – 30 …….(2) Substituting the value of 3X from Eq. (1) in Eq. (2), We get, 2 (2Y) = 5Y – 30 ∴ Y = 30 Ω

16

9011041155 / 9011031155

12. Equal lengths of magnin (ρ1) and nichrome (ρ2) are joined in the left gap and right gap of meter-bridge. The null point is at 40cm from the left end. Compare the diameters of the wire. The specific resistances are ρ1 = 4.8 × 10-8 Ωm, ρ2 = 10-6 Ωm.

Ans: Given : Length of Mangnin LM = 40cmLength of Nichrome LN = 60cmρ1 = 4.8 × 10-8 Ωm, ρ2 = 10-6 Ωm

To find : We know,

…(1)

…(2)When the network is balanced we have,

If dM and dN are the diameters of the wire

Divide eq. (1) by (2)

13. Determine the current flowing through the galvanometer (G) shown in the fig.

17

9011041155 / 9011031155

Ans:To find Ig we apply Kirchhoff’s voltage law.

Loop ABDA : - 5 I1 – 10 Ig + 15 I2 = 0 ∴ 5 I1 + 15 I2 = 10 Ig

∴ - I1 + 3 I2 = 2 Ig ………… (1) Loop BCDB : -10 (I1 – Ig) + 20 (I2 + Ig) + 10 Ig = 0 ∴ 10 I1 + 10 Ig + 20 I2 +20 Ig + 10 Ig = 0 ∴ I1 – 2 I2 = 4 Ig …………...(2)Adding Equations (1) and (2), we get, I2 = 6 Ig …….(3) Substituting for I2 from Equation (2) in equation (2). ∴ I1 = 12 Ig + 4 Ig = 16 Ig Now, I1 + I2 = 2 A by the data.

∴ 16 Ig + 6 Ig = 2 A ∴ 22 Ig = 2 A

14. A potentiometer wire has a length of 4m and resistance of 4Ω. What resistance must be connected in series with the potentiometer wire and a cell of e.m.f. 2V having internal resistance 2Ω to get a potential drop of 10-3 V/cm along the wire?

Ans: L = 4 m, r = 4 Ω, E = 2 V, rc = 2 Ω The required potential drop per unit length of the wire is

18

9011041155 / 9011031155

Let R be the series resistance for which the desired potential drop is obtained.The current in the circuit is

The potential difference across the wire is

∴ Potential drop per metre of the wire

15. A uniform wire is cut into two pieces such that one piece is twice as long as the other. The two pieces are connected in parallel in the left gap of a meter-bridge. When a resistance of 20Ω is connected in the right gap, the neutral point is obtained at a distance of 60cm from the right end of the wire. Find the resistance of the wire before it was cut into two pieces.

Ans:Let RW be the resistance of the wire before it was cut in two. Let L1, L2 and X1, X2

be the lengths and resistances of the two pieces.

∴ RW = X1 + X2 and (ρ and A being the same) We have L1 = 2L2, R = 20 Ω (in the right gap) LR = 60 cm

∴ LX = 100 – LR = 40 cm, and Since the pieces are connected in parallel, their equivalent resistance is

And, with the bridge balanced,

19

9011041155 / 9011031155

From equation (1) and (2),

∴ The original resistance of the wire is RW = X1 + X2 = 40 + 20 = 60 Ω

16. With an unknown resistance X in the left gap and a resistance of 30Ω in the right gap of meter-bridge the null point is obtained at 40 cm from the left end of the wire. Find i. the unknown resistance and ii. the shift in the position of the null pointa. when the resistances in both the gaps are increased by 15Ω andb. when the resistance in each gap is shunted by a resistance of 8Ω

Ans: We have, R = 30 Ω, LX = 40 cm, LR = 100 – LX = 60 cm With the resistance X in the left gap and R = 30 Ω in the right gap,

∴ The unknown resistance is,

i. When the resistance in each gap is increased by 15Ω, the resistance in the left gap is X’ = X + 15 = 20 + 15 = 35Ω, and the resistance in the right gap is R’ = R + 15 = 45Ω.

Since L’X > LX , the null point shifts to the right by L’X - LX = 43.75 cm – 40 cm = 3.75cm.

ii. When the resistance in each gap is shunted by 8 Ω, the resistance in the left gap is

20

9011041155 / 9011031155

And the resistance in the right gap is

Since L’X > LX, the null point shifts to the right by L’X - LX = 47.5 cm – 40 cm = 7.5cm.

17. A skeleton cube is made of 12 wires each of resistance RΩ connected to a cell of e.m.f. E and of negligible internet resistance. Use Kirchhoff’s laws to find the resistance between a. adjacent corners of the cube i.e. between two ends of any wire or across any one edge. b. the diagonally opposite 4 corners of same face of cube. i.e. across face diagonal.

Ans:The distribution of currents in the various branches of the cube by applying Kirchhoff’s first law, and making use of the principle of symmetry, is shown above in the figure.a. Resistance between adjacent corners of the cube :

Let a current i1 + 2i2 enter the junction A of the cube ABCDEFGH.Applying Kirchhoff’s second law to the loop DHGCD,(i2 - i3)r + 2(i2 - i3)r + (i2 - i3)r - i3r = 0i2r - i3r + 2i2r - 2i3r + i2r - i3r - i3r = 0

4i2r - 5i3r = 04i2r - 5i3r = 0

Applying Kirchhoff’s second law to ABCDA, we get :i1r - i2r - i3r - i2r = 0

i1 - 2i2 - i3 = 0

21

9011041155 / 9011031155

Let R be the resistance across AB. Then potential difference across AB = i1r.

(i1 + 2i2)R = i1r

b. Resistance between the diagonally opposite corners of same side of cube :

The distribution of currents in the various branches of the cube by applying Kirchhoff’s first law and making use of the principle of symmetry is shown in the above figure.

Applying Kirchhoff’s second law to the loop ABGFA, we get :

2i1 - 3i2 + 2i3 = 0 …(1)Applying Kirchhoff’s second law to the loop ABGFA, we get :

2i1 - 3i2 - 10i3 = 0 …(2)Subtracting equation (2) from equation (1), we get :(2i1 - 3i2 + 2i3) - (2i1 - 3i2 - 10i3) = 0 2i1 - 3i2 + 2i3 - 2i1 + 3i2 + 10i3 = 0

12i3 = 0 i3 = 0 …(3)

Substituting equation (3) in equation (2), we get :2i1 - 3i2 - 10(i3) = 02i1 - 3i2 - 10(0) = 0

2i1 = 3i2

…(4)Now, applying Kirchhoff’s second law in we get :-i1r - (i1 - i3)r + E = 0-i1r - i1r + i3r + E = 0 -2i1r + 0 + E = 0 (∵ i3 = 0)

∴ E = 2i1r …(5)

22

9011041155 / 9011031155

If RAC is the equivalent resistance of the cube between the corners of A and C, then we can write :E - iRAC = 0

E = i RAC …(6)

Comparing equations (5) and (6), we get : 2i1r = i RAC

Now, applying Kirchhoff’s first law at junction A, we get :i = i1 + i1 + i2

= 2i1 + i2

Substituting equation (8) in equation (7) get :2i1r = i RAC

18. Two coils are connected in series in one gap of a meter bridge and the null point is obtained in the middle of the wire by putting 75Ω in the other gap. Two coils aare then connected in parallel and the null point is obtained again in the middle of the wire, the resistance in the other gap is changed by 57Ω. Find the resistance of each coil.

Ans: Let X1 and X2 be the resistances of the two coils. Let XS and XP be the equivalent resistances of their series and parallel combinations, respectively. ∴ XS = X1 + X2 and XP = (X1 . X2) / (X1 + X2) When the coils are connected in series in one gap, let the resistance in the other gap be R1, and when the coils are connected in parallel in one gap, let the resistance in the other gap be R2. Since, XP < XS, R2 < R1.We have , R1 = 75 Ω, R2 = R1 – 57 = 75 – 57 = 18 Ω,

∴ XS = X1 + X2 = R1 = 75 Ω or X2 = 75 – X1 ….. (1)

And

23

9011041155 / 9011031155

Now,

Substituting the value of X2 from Eq. (2) into Eq. (1), X1 (75 – X1) = 1350 or X2

1 – 75 X1 + 1350 = 0 ∴ (X1 – 45) (X1 – 30) = 0 ∴ X1 = 45 Ω or X1 = 30Ω ∴ X2 = 30 Ω or X2 = 45 Ω

19. Find the radius of the wire of length 25m needed to prepare a coil of resistance 25Ω (Resistivity of material of wire is 3.142 × 10-7Ωm)

Ans: Given : ℓ = 25m, R = 25Ω,ρ = 3.142 × 10-7ΩmTo find : r = ?

∴ r = 0.3162mm

20. The resistance of a potentiometer wire is 8Ω and its length is 8m. A resistance box and a 2V battery are connected in series with it. What should be the resistance in the box, if it is desired to have a potential drop of 1μV/mm?

Ans: We have r = 8 Ω, L = 8 m, E = 2V,

Potential gradient,

Now,

24

9011041155 / 9011031155

25