37

David machines

Embed Size (px)

Citation preview

Page 1: David machines
Page 2: David machines

CHASSIS LOCATED TO: BUCKET OR CONCRETE MIXER.

Page 3: David machines

DELTA

Page 4: David machines

TECHNICAL SPECIFICATIONS 1.3 ENGINE Perkins 1104D-44TA -Diesel 4 stroke - 4 cylinders in line -Turbo charged Aftercooled - Direct - Mechanical injection -

Max power [email protected] kW@RPM - Max torque [email protected] Nm@RPM - Water cooled - Dry air filters - USA EPA Tier 3 / EU STAGE IIIA Compliance

TRASMISSION Integral 4x4 - N.4 forward / rearward gears (2 mechanical + 2 hydraulic) - Max speed 32 km/h - Full load Max Slope Pendenza max superabile a pieno carico 40% Hydrostatic - “Automotive” – powered by variable displacement pump and dual displacement hydrostatic motor – electrohydraulic control lever to select a "slow" gear, "fast" gear and “reverse”. Double ratio mechanical gearbox with electric control gear lever to selection of "work" or "transfer" gear. Inching command.

AXLES Hurth load bearing with final epicyclical gearing reducers – Oscillating front axle (± 6°) - Fixed rear axle.

BRAKE Oil-bath disc brakes acting on four wheels powered by a twin independent circuit – Hydraulic inner in-oil power disc parking brake acts directly on rear axle – Emergency brake incorporated directly on service brake.

STEERING Hydrostatic powered by an independent pump controlled by the steering wheel - Four wheel steering by means of double action twin cylinders - Steering Selector Device on Operator's Console for: Front Wheel Drive, 4 Wheel Bi-Lateral Drive, 4 Wheel Parallel Drive - Int. turning radius 2.000 mm - Ext. turning radius 4.300 mm.

FRAME Electrically Welded High-tempered steel – Rotating frame assembled on slew bearing allowing 360° hydraulic rotation - Automatic and negative mechanical Stop\Block – Drum lifting hydraulic control. Hydraulic Chute control (rotation and tilting got by dual action cylinder). In cab and on ground chute actuation.

DRUM Double spiral mixing blade and emergency manhole, double cone and convex end – Hydrostatic gear motor and variable displacement pump – In cab and on ground drum actuation – Hydraulic lifting for fast casting - metric volume approx. 5800 Lt - Concrete Yield 4,5 mc – Drum Speed 18 RPM in both directions 360° drum slewing.

Page 5: David machines

TECHNICAL SPECIFICATIONS 2.3 BUCKET Articulated bucket - N.2 dual action cylinders for arms lifting and n.1 dual action

cylinders for bucket opening/closing – Electro-hydraulic command for bucket's door actuation – Bucket capacity 600 lt - Productivity up to 4 cycle/hour.

CAB Integral with slewing frame. Continous 360° rotation for visibility enhancement during every cycle phase. ROPS and FOPS requirement compliance. - Adjustable - anatomically designed seat with springy ergonomically shaped suspension. - Adjustable armrest with twin joystick. - Thermoformed (ABS) steering column equipped with electronic display. - User friendly dashboard and control panels - Closed cab with lenhanced visibilità - Wiper on fontal winshield.

HYDRAULIC SYSTEM Servo-controlled hydraulic distributor (4 elements) – Hydraulic distributor electrically managed (6 elements) - Volumetric alternative pump for drum rotation 34Lt @ 1000 RPM – Gear pump for utilities 26Lt @ 1000 RPM – Gear pump for power steering 20Lt @ 1000 RPM – Hydrostatic circuit filter (intake) 10 micron; Hydraulic circuit filter (outlet) 40 micron. Aluminum heat exchanger equipped with electrically powered fan.

WATER SYSTEM Rapid Intake Water Pump with "Self-Priming" rotor. In cab and on ground actuation permitted. Two multiposition taps for water delivery - Alternate Water Intake capabilities with quick disconnect hoses and filter - Flow rate 500Lt/min. - Max Pressure 2.2 bar - N.1 water tank integral with slewing frame: capacity approx. 350 lt. - N. 2 auxiliary water tank: capacity approx. 635 Lt - Electronic water meter.

Page 6: David machines

TECHNICAL SPECIFICATIONS 3.3 TechELECTRIC SYSTEM Starter 12V 3kW - Alternator 12V 95A with incorporated regulator. - Battery

12V – 110 Ah.

GROUND COMMAND Water meter and controls for water pump operation, drum rotation, chute actuation and emergency stop.

DIESEL, OIL AND COOLANT Diesel (tank capacity) 120 l - Hydrauli oil (tank capacity) 100 l - Oil motor 9,5l - Engine coolant 7,0 l.

TYRES 18-19,5 - 16 PR.

DIMENSIONS 2.500x6.845x3.270 mm (bucket on ground).

MASS Curb weight 7.800 kg.

HOMOLOGATION Meets CEE road standards.

MACHINE EQUIPMENT Clamshell bucket - Railway application - DAS - Davino Advanced System - Weighing system with printer – Additives - Air conditioning - High pressure cleaning pump - Automatic grasing unit - Rearward camera - Impact sensors - Work lamp - Chute extension.

Page 7: David machines

DIMENSIONS

Page 8: David machines

EVOLUTION

Page 9: David machines

TECHNICAL SPECIFICATIONS 1.3 Engine 4 stroke 4 cylinder turbo diesel 1104D-44T – Water Cooled –Dry Air Filter–Max Power 74 kW @ 2300 RPM–

Stage 3

Transmission 4x4 Hydrostatic (“Air cooled with oil heat exchanger”) powered by variable deliver pump and dual displacement hydraulic motor controlled by an electro-hydraulic selector lever producing a high-low ratio in both forward and reverse – Max speed 28 Km/H – Hydraulic Accelerator - Inching Pedal.

Axles over-sized load bearing with final epicyclical gearing reducers – Front axel able to oscillate at 10° - Fixed rear axle.

Electrical System Starter 12V 3 kW. Alternator 12V 90A with regulator incorporated. Battery 12V 92Ah.

Brakes inner in-oil power disc brakes acting on all four wheels with power supplied by a twin circuit independent pump – Hydraulic inner in-oil power disc parking brake acts directly on rear axel – Emergency brake incorporated directly on service brake

Frame Electrically Welded High-tempered steel - Frame mounted on roller bearing swivel ring with 315° hydraulic rotation - Automatic and negative mechanical Stop\Block – Control of the hydraulic lifting of drum cylinder by double effect Chute with hydraulic tilt and dual action cylinder controlled from Operator’s Turret or from the ground and hydraulic rotation by dual action cylinder controlled from Operator’s Turret.

Steering Hydrostatic (Orbital Type) fed by an independent pump controlled by steering wheel - Four wheel steering by means of double action twin cylinders- Steering Selector Device on Operator’s Console for: Front Wheel Drive, 4 Wheel Bi-Lateral Drive, 4 Wheel Parallel Drive

Page 10: David machines

TECHNICAL SPECIFICATIONS 2.3 Bucket Loading arm with fixed high pendant dumping bucket for fast and hassle free

discharge of aggregates - Cap. 600Lt– Loader Arms with 2 lifting cylinders and dual return action – 8 loading shovel - Single lever control

Water System Rapid Intake Positive Displacement Water Pump with "Self-Priming" Rotor, controlled by both the driver’s seat from the ground – Delivery 500Lt/min. - Max Pressure 2.2 bar – Dual Standard Water tanks approx. 650 Lt – Two multi-position taps for water delivery to mixing drum - Alternate Water Intake capabilities with quick disconnect hoses and filter- cleaning hose – Electronic water meter – Emergency stop from ground

Operator’s Turret Welded to the rotating frame, with a possibility to rotate at 315° allowing perfect visibility in transfer and work phases - Adjustable anatomically designed seat with springy suspension ergonomically shaped for easy access to controls – Adjustable articulated armrest with joystick – Steering column thermoformed with electronic display instrumentation easily accessible and readablev - User friendly dashboards and control panels- Closed cab with large high visibility windshield and wiper

Hydraulic System 3 Component Hydaulic Distributor - Variable cylindered pump and piston for rotation drive of drum 34Lt @ 1000 RPM – Geared pump for utilities 26Lt @ 1000 RPM – Geared pump for power steering 20Lt @ 1000 RPM – Max pressure 250 bar – Hydrostatic circuit filter (intake) 10 microns; Hydraulic Circuit filter (intake) 25 microns.

Page 11: David machines

TECHNICAL SPECIFICATIONS 3.3 Drum Trilateral discharging, double spiral mixing blade drum with

emergency manhole, double cone and convex – Hydrostatic motor-gear and variable delivery pump with orbital engine together of the redactor – Electro-hydraulic command both from the operator’s turret or from ground - Geometric volume approx.. 5100 Lt (1347 gals.) Max Concrete Yield 3,6 mc – Drum Speed 22 RPM in both directions – Drum flexible to 180° - Hydraulic telescopic hoisting cylinder for easy and quickly discharge of cement

Ground commands water meter and controls for water pump operation, drum rotation, up/down chute and emergency stop

Dimensions (Bucket Down) L-6930 mm (@272”) W-2330 mm (@91”) H-3160 mm.(@ 124”).

Weight with open cab kg - Tires 18-19.5/16 PR - Meets CEE road standards

Page 12: David machines

DIMENSIONS

Page 13: David machines

PRIMA

Page 14: David machines

TECHNICAL SPECIFICATIONS 1.3 Engine Perkins 404D-22 – Diesel stroke 4 – 4 cylinder fuel injected - Water Cooled – Dry Air Filter –

Max Power 37,3 kW @ 2800 RPM (HP51) – Stage 3

Transmission 4x4 Hydrostatic Automative (“Air cooled with oil heat exchanger”) powered by variable deliver pump and dual displacement hydraulic motor controlled by an electro-hydraulic selector lever producing a high-low ratio in both forward and reverse – Max speed 20,5 Km/H (13 MPH). - Inching Pedal.

Axles both over-sized load bearing with final epicyclical gearing reducers – Fixed front axel – Rear axle able to oscillate at 10°.

Electrical System Starter 12V 2 kW. Alternator 12V 65A - Battery 12V 70Ah.

Brakes inner in-oil power disc brakes acting on all four wheels with power supplied by a twin circuit independent pump – Hydraulic inner in-oil power disc parking brake acts directly on rear axel – Emergency brake incorporated directly on service brake.

Frame Electrically Welded High-tempered steel – Manually positionable chute – Hydraulic command Hopper max. discharge height 1300 mm – Chute max discharge height 1100 mm6 bucks per load - Single lever control

Page 15: David machines

TECHNICAL SPECIFICATIONS 2.3 Steering Hydrostatic (Orbital Type) fed by an independent pump controlled by steering

wheel - Four wheel steering by means of double action twin cylinders- Steering Selector Device on Operator’s Console for: Front Wheel Drive/ 4 Wheel Bi-Lateral Drive/ 4 Wheel Parallel Drive – Minimum steering radius mm 900.

Bucket Loading arm with fixed high pendant dumping bucket for fast and hassle free discharge of aggregates. Cap. 230 Lt (61 gals.) - Loader Arm driven by a double acting hydraulic cylinder – Nr 6 bucks per load - Single lever control

Water System Rapid Intake Positive Displacement Water Pump with "Self-Priming" Rotor – Delivery 500Lt/min. (131 gals.) - Max Pressure 2,2 bar – Dual Standard Water tanks approx. 350 Lt (92 gals) – Two switches three way flow and use a ball valve and connected directly to the spray lance - Alternate Water Intake capabilities with quick disconnect hoses and filter - Cleaning hose – Electronic water meter – Emergency stop from ground

Operator’s Turret adjustable anatomically designed seat with springy suspension ergonomically shaped for easy access to controls – User friendly dashboards and control panels- 3 sided enclosed cab (optional cab with total closure) with large high visibility windshield and wiper

Page 16: David machines

TECHNICAL SPECIFICATIONS 3.3 Hydraulic System 3 Component Hydaulic Distributor - Steering gear pump and

drum tilt 6,3Lt @ 1000 RPM – Bucket and water pump motor gear pump 17Lt @ 1000 RPM, 2 nd speed drum drive motor and water pump – Variable delivery pump 8Lt @ 1000 RPM for 1st speed drum– Max pressure 160 bar – Hydrostatic circuit filter (intake) 10 microns; Feedback circuit filter 40 microns.

Drum double spiral mixing blade drum with emergency manhole, double cone and convex bottom – Hydrostatic motor-gear and variable delivery pump controlled by levers produce a two speed drum rotation –- Geometric volume approx.. 1400 Lt (370 gals) - Max Concrete Yield 1,1mc (1,3cubic yards) – Drum Speed 24 RPM in both directions - Drum lift cylinder double effect for quick unload

Dimensions L-4500 mm. W-1790 mm. H-2460 mm.. (Bucket Down)

Weight with open cab 2600 kg -Tires 12. x 16.5/10 PR - Meets CEE road standards

Page 17: David machines

DIMENSIONS

Page 18: David machines

RANGER

Page 19: David machines

TECHNICAL SPECIFICATIONS 1.3 Engine 4 stroke 4 cylinder turbo diesel 804C - 33T – Water Cooled –Dry Air Filter–Max Power 60 kW

@ 2600 RPM (HP80) – Stage 3

Transmission 4x4 Hydrostatic ("Air cooled with oil heat exchanger") powered by variable deliver pump and dual displacement hydraulic motor controlled by an electro-hydraulic selector lever producing a high-low ratio in both forward and reverse – Max speed 30 Km/H (19 MPH). Inching Pedal.

Axles Hurth over-sized load bearing with final epicyclical gearing reducers – Front axel able to oscillate at 10° - Fixed rear axle .

Electrical System Starter 12V 3 kW. Alternator 12V 90A with regulator incorporated. Battery 12V 92Ah. Electric Start/Stop switch – Gauges for engine temp. and hour meter - Indicator lights for glow plugs, generator, turn signals, lights, oil pressure, and fuel level - Contains a horn and fuse box with water proof relays – Warning beacon switch - A safety sensor under the seat allows machines machine movement only if the operator is seated - Engine can only be started in neutral.

Brakes inner in-oil power disc brakes acting on all four wheels with power supplied by a twin circuit independent pump – Hydraulic inner in-oil power disc parking brake acts directly on rear axel – Emergency brake incorporated directly on service brake.

Page 20: David machines

TECHNICAL SPECIFICATIONS 2.3 Steering Hydrostatic (Orbital Type) fed by an independent pump controlled by steering wheel - Four

wheel steering by means of double action twin cylinders- Steering Selector Device on Operator’s Console for: Front Wheel Drive/ 4 Wheel Bi-Lateral Drive/ 4 Wheel Parallel Drive.

Frame Electrically Welded High-tempered steel - Frame mounted on roller bearing swivel ring with 180° hydraulic rotation - automatic and negative mechanical Stop\Block - Chute with hydraulic tilt and dual action cylinder controlled from Operator’s Turret which is independent from Drum Tilt – Manual 180° chute rotation

Bucket Loading arm with fixed high pendant dumping bucket for fast and hassle free discharge of aggregates. Cap. 500Lt (132 gals.) - Loader Arms with 2 lifting cylinders and dual return action – Single lever control

Water System Rapid Intake Positive Displacement Water Pump with "Self-Priming" Rotor – Delivery 500Lt/min. (132 gals.) - Max Pressure 2.2 bar – Dual Standard Water tanks approx. 500Lt (132 gals) – Two multi-position taps for water delivery to mixing drum - Alternate Water Intake capabilities with quick disconnect hoses and filter- cleaning hose – water meter

Operator’s Turret rotate able, mounted on ball-bearing swivel ring - adjustable anatomically designed seat with springy suspension ergonomically shaped for easy access to controls – user friendly dashboards and control panels- 3 sided enclosed cab (optional cab with total closure) with large high visibility windshield and wiper

Page 21: David machines

TECHNICAL SPECIFICATIONS 3.3 Hydraulic System 3 3 Component Hydaulic Distributor - Variable cylindered pump and

piston for rotation drive of drum 34Lt @ 1000 RPM – Geared pump for utilities 26Lt @ 1000 RPM – Geared pump for power steering 6Lt @ 1000 RPM – Max pressure 250 bar – Hydrostatic circuit filter (intake) 10 microns; Hydraulic Circuit filter (intake) 25 microns.

Drum Trilateral discharging, double spiral mixing blade drum with emergency manhole – hydrostatic motor-gear and variable delivery pump controlled by an infinitesimal toggle switch on the control panel for mix/discharge operations (optional remote control) – hydraulic telescopic drum lift- Geometric volume approx.. 3100 Lt (792 gals) – Max Concrete Yield 2,1 mc (2,6 cubic yards) – Drum Speed 24 RPM in both directions – Drum flexible to 180° - Hydraulic dual effect hoisting cylinder for easy discharge of cement.

Dimensions L-5875. W-2000 mm. H-2940 mm.. (Bucket Down)

Weight with open cab 4400kg

Tires 12.5 x 18 16 PR EM All Terrain

Meets CEE road standards

Page 22: David machines

DIMENSIONS

Page 23: David machines

MASTER

Page 24: David machines

TECHNICAL SPECIFICATIONS 1.3 Engine 4 stroke 4 cylinder turbo diesel 804D - 33T – Water Cooled –Dry Air Filter–Max Power 74 kW

@ 2.300 – Stage 3

Transmission 4x4 Hydrostatic (“Air cooled with oil heat exchanger”) powered by variable deliver pump and dual displacement hydraulic motor controlled by an electro-hydraulic selector lever producing a high-low ratio in both forward and reverse – Max speed 28 Km/H - Inching Pedal.

Axles over-sized load bearing with final epicyclical gearing reducers – Front axel able to oscillate at 10° - Fixed rear axle.

Electrical System Starter 12V 3 kW. Alternator 12V 90A with regulator incorporated. Battery 12V 92Ah.

Brakes inner in-oil power disc brakes acting on all four wheels with power supplied by a twin circuit independent pump – Hydraulic inner in-oil power disc parking brake acts directly on rear axel – Emergency brake incorporated directly on service brake.

Steering Hydrostatic (Orbital Type) fed by an independent pump controlled by steering wheel - Four wheel steering by means of double action twin cylinders- Steering Selector Device on Operator’s Console for: Front Wheel Drive, 4 Wheel Bi-Lateral Drive, 4 Wheel Parallel Drive.

Page 25: David machines

TECHNICAL SPECIFICATIONS 2.3 Frame Electrically Welded High-tempered steel - Frame mounted on roller bearing swivel ring with

180° hydraulic rotation - Automatic and negative mechanical Stop\Block – Control of the hydraulic lifting of drum cylinder by double effect Chute with hydraulic tilt and dual action cylinder controlled both from Operator’s Turret or from the ground which is independent from Drum Tilt – Manual 180° chute rotation

Bucket Loading arm with fixed high pendant dumping bucket for fast and hassle free discharge of aggregates - Cap. 600Lt (158 gals.) – Loader Arms with 2 lifting cylinders and dual return action – Six loading shovel - Single lever control

Water System Rapid Intake Positive Displacement Water Pump with "Self-Priming" Rotor, controlled by both the driver’s seat from the ground – Delivery 500Lt/min. (132 gals.) - Max Pressure 2.2 bar – Dual Standard Water tanks approx. 550Lt – Two multi-position taps for water delivery to mixing drum - Alternate Water Intake capabilities with quick disconnect hoses and filter- cleaning hose – Electronic water meter - Emergency stop from ground

Operator’s Turret rotate able, mounted on ball-bearing swivel ring - adjustable anatomically designed seat with springy suspension ergonomically shaped for easy access to controls – Steering column thermoformed with electronic display instrumentation easily accessible and readable - User friendly dashboards and control panels- 3 sided enclosed cab (optional : cab with total closure) with large high visibility windshield and wiper

Page 26: David machines

TECHNICAL SPECIFICATIONS 3.3 Hydraulic System 3 3 Component Hydaulic Distributor - Variable cylindered pump and piston

for rotation drive of drum 34Lt @ 1000 RPM – Geared pump for utilities 26Lt @ 1000 RPM – Geared pump for power steering 20Lt @ 1000 RPM – Max pressure 250 bar – Hydrostatic circuit filter (intake) 10 microns; Hydraulic Circuit filter (intake) 25 microns.

Drum Trilateral discharging, double spiral mixing blade drum with emergency manhole, double cone and convex – Hydrostatic motor-gear and variable delivery pump controlled by an infinitesimal toggle switch on the control panel for mix/discharge operations (optional remote control) – Electro-hydraulic command both from the operator’s turret or from ground - Hydraulic telescopic drum lift- Geometric volume approx.. 3700 Lt - Max Concrete Yield 2,6 mc (3.25 cubic yards) – Drum Speed 27 RPM in both directions – Drum flexible to 180° - Hydraulic telescopic hoisting cylinder for easy and quickly discharge of cement

Ground commands availability from the ground of water meter and controls for operating the water pump, drum rotation, up/down drain and emergency stop

Dimensions (Bucket Down) L-6110 mm. W-2000 mm. H-2940 mm.

Weight with open cab 4950kg (10,913 lbs.) -Tires 112.5/80-18 16 PR - Meets CEE road standards

Page 27: David machines

DIMENSIONS

Page 28: David machines

EXCLUSIVE

Page 29: David machines

DIMENSIONS

Page 30: David machines

RUNNER

Page 31: David machines

TECHNICAL SPECIFICATIONS 1.3 Engine 4 stroke 4 cylinder turbo diesel 1104D-44T – Water Cooled –Dry Air Filter–Max Power 74 kW

@ 2.300 RPM– Stage 3

Transmission 4x4 Hydrostatic (“Air cooled with oil heat exchanger”) powered by variable deliver pump and dual displacement hydraulic motor controlled by an electro-hydraulic selector lever producing a high-low ratio in both forward and reverse – Max speed 28 Km/H - Inching Pedal.

Axles over-sized load bearing with final epicyclical gearing reducers – Front axel able to oscillate at 10° - Fixed rear axle.

Electrical System Starter 12V 3 kW. Alternator 12V 90A with regulator incorporated. Battery 12V 92Ah.

Brakes inner in-oil power disc brakes acting on all four wheels with power supplied by a twin circuit independent pump – Hydraulic inner in-oil power disc parking brake acts directly on rear axel – Emergency brake incorporated directly on service brake.

Steering Hydrostatic (Orbital Type) fed by an independent pump controlled by steering wheel - Four wheel steering by means of double action twin cylinders- Steering Selector Device on Operator’s Console for: Front Wheel Drive, 4 Wheel Bi-Lateral Drive, 4 Wheel Parallel Drive.

Page 32: David machines

TECHNICAL SPECIFICATIONS 2.3 Frame Electrically Welded High-tempered steel - Frame mounted on roller bearing swivel ring

with 180° hydraulic rotation - Automatic and negative mechanical Stop\Block – Control of the hydraulic lifting of drum cylinder by double effect Chute with hydraulic tilt and dual action cylinder controlled both from Operator’s Turret or from the ground which is independent from Drum Tilt – Manual 180° chute rotation

Bucket Loading arm with fixed high pendant dumping bucket for fast and hassle free discharge of aggregates - Cap. 600Lt– Loader Arms with 2 lifting cylinders and dual return action – 10 loading shovel - Single lever control

Water System Rapid Intake Positive Displacement Water Pump with "Self-Priming" Rotor, controlled by both the driver’s seat from the ground – Delivery 500Lt/min. - Max Pressure 2.2 bar – Dual Standard Water tanks approx. 800 Lt – Two multi-position taps for water delivery to mixing drum - Alternate Water Intake capabilities with quick disconnect hoses and filter- cleaning hose – Electronic water meter - Emergency stop from ground

Operator’s Turret rotate able, mounted on ball-bearing swivel ring - Adjustable anatomically designed seat with springy suspension ergonomically shaped for easy access to controls – Steering column thermoformed with electronic display instrumentation easily accessible and readable - User friendly dashboards and control panels- Closed cab with large high visibility windshield and wiper

Page 33: David machines

TECHNICAL SPECIFICATIONS 3.3 Hydraulic System 3 3 Component Hydaulic Distributor - Variable cylindered pump and

piston for rotation drive of drum 34Lt @ 1000 RPM – Geared pump for utilities 26Lt @ 1000 RPM – Geared pump for power steering 20Lt @ 1000 RPM – Max pressure 250 bar – Hydrostatic circuit filter (intake) 10 microns; Hydraulic Circuit filter (intake) 25 microns.

Drum Trilateral discharging, double spiral mixing blade drum with emergency manhole, double cone and convex – Hydrostatic motor-gear and variable delivery pump with orbital engine together of the redactor – Electro-hydraulic command both from the operator’s turret or from ground - Geometric volume approx.. 5.800 Lt Max Concrete Yield 4,0 mc – Drum Speed 18 RPM in both directions – Drum flexible to 180° - Hydraulic telescopic hoisting cylinder for easy and quickly discharge of cement

Ground commands availability from the ground of water meter and controls for operating the water pump, drum rotation, up/down drain and emergency stop

Dimensions (Bucket Down) L-6.930 mm (@272”) W-2.360 mm (@91”) H-3.180 mm.(@ 124”).

Weight with open cab 7.160 Kg -Tires 18-19,5 16 PR - Meets CEE road standards

Page 34: David machines

DIMENSIONS

Page 35: David machines

MINIDUMPER

Page 36: David machines

TECHNICAL SPECIFICATIONS Lenght: mm760

Lenght without thebucket: mm1732

Lenght w/bucket down: mm2318

Height: mm1311

Clearance: mm111

Ground pressare (empty): Kg/cmq0,16

Ground pressure (fullload): Kg/cmq0,4

Track: 190x37x72

Honda Diesel Engine: GX2709hp3600rpm

Electric starter: GX2709hp3600rpm

Transmission: Hydraulic

Speed: Km/h2,3-3,2

Bucket Load: Kg600

Platform load: Kg800

Operational weight: Kg490

Dumping height: mm500

Slope: 25°(35%)

Roller spertracks: 8

Auxiliary hydraulica: l/min14

Page 37: David machines

CONTACT For more details, contact:

Mr. Ugorji Okorie (+234- 8184576955 & 8067117637 [email protected] Skype: ugorji.okorie

Our Official Representative on Nigeria.