Upload
lewo-romania
View
112
Download
1
Embed Size (px)
DESCRIPTION
LEWO Romania ofera variante diverse de curatare pentru domeniul industrial, de la petrol si gaze, productie, transport, administratie, la procesul alimentar si agricultura, asigurand orice necesitate pe aceste domenii. Portofoliul de produse cuprinde o gama vasta si certificata de detergenti utilizati in domeniul industrial si in domeniul casnic. Ca distribuitor exclusiv, LEWO Romania a introdus cu succes in piata din Romania produsele Biobased. Impreuna cu specialistii nostri, puteti gasi oricand cea mai buna solutie care sa indeplineasca cerintele dumneavoastra.
Citation preview
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
APPLICATIONS:
Oil & Gas | Industrial | Transportation | Government | Food Process & Agricultural
Oil & Gas:SAFE CARE® cleaning products, specifically SC-1000 which is listed with the USEPA
National Oil & Hazardous Substances Pollution Contingency Plan (NCP), cleans by
reducing the surface tension of the oil at the substrate surface, weakening the polar
attraction of oil to the surface which then allows it to be rinsed from the surface and
captured. Major Oil & Gas service companies are drawn to the benefits of using non-
toxic, non-hazardous cleaners and solvents for a variety of applications including tank
cleaning, degassing, equipment maintenance, oil herding, oil/water separation and Rig
maintenance. Our high-performance non-ionic surfactant, SC-1000 and our non-
evaporative, water soluble solvent, SC-SuperSolv, have shown tremendous promise as
a direct replacement or as an additive for the following functions:
Enhanced Oil Recovery / Improved Yields
Oil Spill Recovery /Soil Remediation
Cooling Pond Clarification / Oil Water Separation
Down-hole Drilling Muds / Wellbore Productivity
Bench testing was conducted with contaminated "mud" samples to
demonstrate release. We used our non-evaporative solvent called
SC-EZ-Solv to soften the tar-like petroleum in the soil. Then, we
introduced our nonionic surfactant called SC-1000 Aqueous Cleaner at a
5% solution which caused the petroleum and solvent to immediately
release and separate from the soil so that it could be captured at the top
of the water column.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
• Petroleum distillates
• Glycol ethers
• Terpenes
• Synthetics
• Builders & reagents
• Caustics
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
APPLICATIONS:
Oil & Gas | | Transportation | Government | Food Process & Agricultural Industrial
Industrial /
Manufacturing:
The manufacturing sector offers a vast array of applications that can be
addressed by GEMTEK® products. Without sacrificing performance, SAFE
CARE® industrial cleaners and solvents replace traditional products that
create greater liabilities due to their negative effects on waste discharge.
Old-school, traditional chemistries resulting in costly clean-up measures and
penalties; additional liability results from human and environmental impact
from toxic and caustic chemistries. Major challenges in the industrial sector
include precision cleaning of high quality mil specs; surface maintenance of
metal processing and the machining of metals, plastics, coatings and other
synthetic materials; the maintenance of dies, presses, cutting, bending and
forming tools, casting molds, lathes, polishing equipment and their cooling
and heat exchanger systems, exhaust waste treatment and spill recovery
systems; filtration and re-circulating systems and other CIP maintenance
activities. SAFE LUBE industrial lubricants and metalworking fluids can
replace petroleum and synthetic products, which significantly reduce
environmental hazards presented by routine use and spills.
Metalworking
Manufacturing
Parts Washing
Processing Cleaning
Facilities Maintenance
Power Transfer Systems
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
• Petroleum distillates
• Glycol ethers
• Terpenes
• Synthetics
• Builders & reagents
• Caustics
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
APPLICATIONS:
Oil & Gas | Industrial | | Government | Food Process & Agricultural Transportation
Transportation:
SAFE CARE® and SAFE LUBE products are used very successfully in all areas
of the transportation industry. SAFE CARE® products may be used for drive-
thru wash racks for buses, trucks, rail cars, and automobiles and interior
maintenance for hard surfaces and textiles. Whether its commercial or
military vessels, SAFE CARE® products may be used for cleaning fuel tanks,
bilges, refrigerator containers, cargo holds, galleys and passenger
compartments. SAFE CARE® products effectively degrease carbon soot from
fuel exhaust areas to engine blocks; from runway / concrete cleaning to
heavy-duty equipment maintenance. Unlike most caustic cleaners, SAFE
CARE® products do not contain reagents that oxidize finishes, causing rust
and degrading elastic materials such as rubber or vinyl, but actually improves
the life of hoses, seals, gaskets, paint finishes and other hard surfaces.
SAFE LUBE products are available for all types of hydraulic systems, as well as
gear lubricants and wire rope lubricants that are safe to use around shipping
ports, commercial marinas, and depots.
Aviation
Marine
Rail / Bus
Trucking
Automotive
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
• Petroleum distillates
• Glycol ethers
• Terpenes
• Synthetics
• Builders & reagents
• Caustics
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
APPLICATIONS:
Oil & Gas | Industrial | Transportation | | Food Process & Agricultural Government
Government:
Government facilities and installations use vast amounts of traditional
chemistries that do not comply with Executive Order 13101 and 13134, which
mandate the use of biobased products. The recent USDA Farm Bill Section
9002 legislation, OSHA and the DOE are all moving quickly to implement
strict use of renewable resource, plant-based, non-toxic and readily
biodegradable products. Applications that may be addressed are similar to
those outlined in the industrial, transportation and petroleum sectors.
SAFE CARE® products work extremely well in janitorial application and do
not present a threat to users or the environment and enhance the lifecycle of
the surfaces they clean.
Applications range from aircraft cleaning to onboard ship maintenance as
well as government building maintenance to forestry and national park
maintenance.
Military: Air Force, Navy & Army
Department of Defense
Department of the Interior
Department of Energy
Department of Agriculture
Environmental Protection Agency
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
• Petroleum distillates
• Glycol ethers
• Terpenes
• Synthetics
• Builders & reagents
• Caustics
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
APPLICATIONS:
Oil & Gas | Industrial | Transportation | Government | Food Process & Agricultural
Food Process
&
Agricultural:
Commercially grown fruits and vegetables generally contain harmful residues of
pesticides, fungicides, fertilizers, food waxes and other organic soils. Many of the
contaminant soils found on fruits and vegetables contain petroleum distillates such
as paraffin or mineral oil. Other toxic chemicals include terpenes, glycol ethers and
reagents such as sodium hydroxide or ammonia compounds. These contaminants
are often derived from pest control and residual products from operating and/or
cleaning agricultural equipment. SAFE CARE® cleaning products and SAFE LUBE
industrial lubricants may improve or eliminate soil contamination, therefore
improving the overall safety and quality of the agricultural product. SAFE CARE®
cleaning products are USDA compliant and may be used in the process waters of
post harvest, fresh cut and processed fruits and vegetables. SAFE CARE®
products may be used in all major processing steps including multi-stage flumes,
chill tanks, coolers, washing equipment and food processing systems. SAFE LUBE
products may be used with agricultural equipment where hydraulics are used, gear
oil for conveyor belts, and general purpose lubricants for food processors. Recent
testing has proven that when orchard fruit such as apples or citrus are cleaned with
SC-1000 Aqueous Cleaner that the shelf-line is actually extended with less fruit
loss to rot.
Food Process:
Food Process Cleaning
Meat, Poultry and Fish Processing
Dairy Product Processing
Beverage Production
Breweries
Agricultural:
Irrigation Cleaner
Root Stimulator
Soil Remediation
Equipment Cleaning
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
GEMTEK® Products
SAFE CARE® PRODUCTS DO NOT CONTAIN:
• Petroleum distillates
• Glycol ethers
• Terpenes
• Synthetics
• Builders & reagents
• Caustics
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
PRODUCTS AT WORK - OIL & GAS # 1:
Heavy deposits of asphaltenes were first removed with a spatula, then SC-EZ-Solv Safety Solvent was spray
applied and agitated with a plastic brush to loosen the hydrocarbon build-up. After the majority of the
asphaltenes were removed, a 50% solution of SC-1000 Aqueous Cleaner was used with a pressure washer as a
final step in removing the hydrocarbon soil.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
GEMTEK® Products
SAFE CARE® PRODUCTS DO NOT CONTAIN:
• Petroleum distillates
• Glycol ethers
• Terpenes
• Synthetics
• Builders & reagents
• Caustics
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
PRODUCTS AT WORK - OIL & GAS # 2:
Cleaning large pistons from Wartsila engines in pump station using SC-SuperSolv Safety Solvent, our non-
evaporative, water miscible solvent, was sprayed applied and rinsed off with water.
PRODUCTS AT WORK - OIL & GAS # 3:
For cleaning petroleum hydrocarbon, SC-1000 Aqueous Cleaner Concentrate at a 50% solution was sprayed on and wiped
off. Less product concentration could be used with additional dwell time and/or agitation.
GEMTEK® Products
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
PRODUCTS AT WORK - OIL & GAS # 4:
Oil spill barriers were pre-treated with our non-evaporative solvent, SC-EZ-Solv Safety Solvent, to loosen the
heavy asphaltene deposits, then a 6% solution of SC-1000 Aqueous Cleaner was used as a final step to
remove the hydrocarbon soil and solvent.
PRODUCTS AT WORK - OIL & GAS # 5:
SC-SuperSolv Safety Solvent, our non-evaporative, water miscible solvent was used to removed the polymerized petroleum
from the exterior of a tank.
For testing purposes, SC-SuperSolv was spray applied, allowed to dwell for 5 - 10 minutes before agitation. The soil was
removed with a water rinse.
GEMTEK® Products
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
PRODUCTS AT WORK - Parts Washing # 1:
SC-1000 Aqueous Cleaner Concentrate is used for parts washing for all ferrous metals, however, SC-Aircraft
& Metal Cleaner is specially formulated for non-ferrous metal such as aluminum.
PRODUCTS AT WORK - Parts Washing # 2:
SC-1000 Aqueous Cleaner and SC-SuperSolv Safety Solvent were blended together at an 80/20 blend and diluted to a
50% solution and allowed to dwell for 30 minutes to remove baked on hydrocarbon soil.
GEMTEK® Products
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
PRODUCTS AT WORK - Copper Coil Cleaning:
A bath of SC-OmniBrite Acid was used
to clean copper fin coils.
The coils were allowed to dwell
overnight and then rinsed with water
in the morning; no agitation was used.
Dwell time will vary depending on the
soil.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
GEMTEK® Products
SAFE CARE® PRODUCTS DO NOT CONTAIN:
• Petroleum distillates
• Glycol ethers
• Terpenes
• Synthetics
• Builders & reagents
• Caustics
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
PRODUCTS AT WORK - Exterior Aircraft Cleaning:
SC-Aircraft & Metal Cleaner Concentrate is diluted to a 10% solution for routine cleaning of exterior aircraft surfaces.
A higher concentration may be needed for heavier soils such as carbon soot, brake fluid and lubricants.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
• Petroleum distillates
• Glycol ethers
• Terpenes
• Synthetics
• Builders & reagents
• Caustics
GEMTEK® Products
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
PRODUCTS AT WORK - Transportation # 2:
A city bus was pretreated with a 10% solution of SC-1000 Aqueous Cleaner when a hydraulic line broke, and a 5%
solution of SC-SuperSolv when an advertisement sign was removed before going through the wash tunnel.
PRODUCTS AT WORK - Transportation # 3:
SC-1000 Aqueous Cleaner is diluted to a
5-10% solution for exterior cleaning of
stainless steel passenger trains using a
pressure washer.
GEMTEK® Products
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
PRODUCTS AT WORK - Industrial # 1:
Various equipment such as a brake cleaning machine at a military depot were cleaned using a 50/50 blend of SC-
SuperSolv Safety Solvent and SC-1000 Aqueous Cleaner at a 20% solution for a spray-on, wipe-off application.
PRODUCTS AT WORK - Industrial # 2:
For cleaning the honeycombs in a cooling
turbine, a side-by-side cleaning trial
compared the use of SC-SuperSolv Safety
Solvent on the left and the traditional cleaner
that was currently used on the right.
GEMTEK® Products
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
PRODUCTS AT WORK - Institutional # 1:
SC-Exhaust Hood & Filter Cleaner is used at a 50% dilution and allowed to dwell for 5 minutes to clean
exhaust hood parts.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
• Petroleum distillates
• Glycol ethers
• Terpenes
• Synthetics
• Builders & reagents
• Caustics
GEMTEK® Products
The information contained herein is believed to be correct including
test data conducted under controlled laboratory conditions. Users of
SAFE CARE products should perform their own test(s) to determine
the suitability of the product for their specific application(s).
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
PRODUCTS AT WORK - Institutional # 1:
Feasibility Study 413
Storage Vessel Decommissioning
We were asked to find a solution for removing and reclaiming petroleum hydrocarbons from storage vessels
located offshore. Although the exact type of contaminants are unknown, it is assumed that the contents
include crude oil, drilling muds, and/or organic materials with seawater.
We have proposed an 80/20 blend of SC-1000 Aqueous Cleaner Concentrate and SC-SuperSolv Safety
Solvent at a 2% solution. The product will be poured into the vessel and allowed to dwell for an extended
period of time. The use of heat or agitation is not practicable, and therefore will not be considered.
Day 1: The contaminants were put into the bottom of the beaker and seawater was poured into
the beaker. Then the blend of SC-1000 and SC-SuperSolv was added at a 2% concentration.
Day 2: Observed the release of micro-emulsion (gases) and a ring of lighter hydrocarbon
factions at the top.
Day 14: Observed the continued release of micro-emulsion (gases) with two distinct rings at
the top along with a transitional interfacial separation of hydrocarbon.
Day 15: Agitated the solution to observe whether phase separation will occur again.
Day 34: After the solution was agitated it took 4 days for the solution to start separating again.
You can see a ring of the light hydrocarbons at the top along with some of the black
hydrocarbons.
Day 34: We also observed reflective particles dispersed throughout the solution. We are not
able to determine what the particles are at this time as we do not want to disturb the solution
again.
GEMTEK® Products
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-1000 Aqueous Cleaner Concentrate
DESCRIPTION: SC-1000 Aqueous Cleaner Concentrate is our most versatile and powerful non-ionic surfactant
system used in a variety of industrial and commercial applications. Comprised of fatty alcohols,
free fatty acids and fatty esters, SC-1000 is a colloidal solution that creates a unique
hydrocarbon release agent that can tolerate tremendous soil load. The powerful micelle
cleaning action of SC-1000 will cause long chain hydrocarbon soils including fats, greases, oils,
proteins and sugars to repel from the surface so that they can be rinsed away with water,
without damaging or reacting with the cleaning surface. SC-1000 is not a typical caustic
detergent or petroleum solvent, therefore it will not damage or react with the cleaning surface.
SC-1000 meets with the following requirements:
USEPA Design for the Environment (DfE)
USEPA National Oil & Hazardous Substances Pollution Contingency Plan (NCP) *
USDA BioPreferred® Program
EU REACH Pre-registered
CEFAS Reg. 25334 North Sea
USDA A1 General Cleaning & L1 Drain/Sewer Acceptable
California’s SCAQMD as a Clean Air Solvent.
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
NSN 6850-01-474-1273 (5 gal.); 6850-01-474-1311 (55 gal.)
*SC-1000™ is on the USEPA NCP Product Schedule under Surface Washing Agents. This listing does not
mean that EPA approves, recommends, licenses, certifies or authorizes the use of SC-1000 on an oil
discharge. The listing means only that data has been submitted to EPA as required by Subpart J of the
NCP § 300.915.
INSTRUCTIONS: Rinse surface to remove loose particulate soil before cleaning. The product should be diluted
with water depending on the specific application. Less product may be necessary with increased
temperature, dwell time or agitation. Rinse with water to remove soil and residual product.
Water-break or sheeting action should be observed on smooth hard surfaces.
Suggested Dilutions: Difficult Cleaning 50% - 20%
Average Cleaning 20% - 5%
Light Cleaning 5% - .5%
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, very light amber liquid
Odor: Mild surfactant
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.004
Relative Density: Greater than water
pH Range: 10.2 – 10.5
HLB: 13.85
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-2000 All-Purpose Cleaner
DESCRIPTION: SC-2000 All-Purpose Cleaner is a ready-to-use non-ionic surfactant cleaner
that will release hydrocarbon soils including fats, greases, oils, and sugars without
reacting with the cleaning surface. SC-2000 All-Purpose may be use on all “water-
safe” surfaces. Based on our most powerful cleaning chemistry approved by the USDA
for general cleaning (A1), SC-2000 All-Purpose Cleaner is ideal for use in the food
and beverage industry. SC-2000 All- Purpose Cleaner complies with:
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
USEPA Design for the Environment (DfE)
USDA BioPreferred® Program
NSN 7930-01-508-2735 (5 gal.); 7930-01-508-2741 (55 gal.); 6850-01-505-7204
(bulk)
INSTRUCTIONS: Rinse surface to remove loose soil before cleaning. The product may be used full
strength or diluted with water depending on the specific application. Less product
may be necessary with increased temperature, dwell time or agitation. For best
results, rinse with water to remove soil and residual product.
Suggested Dilutions: Difficult Cleaning 100% - 50%
Average Cleaning 50% - 25%
Light Cleaning 20% - 5%
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT
CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, very light amber liquid
Odor: Mild surfactant
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.004
Relative Density: Greater than water
pH Range: 10.2 – 10.5
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform
their own test(s) to determine the suitability of the
product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-4000 Multi-Surface Cleaner
DESCRIPTION: SC-Multi-Surface Cleaner is an all-purpose, ready-to-use non-ionic surfactant cleaner
that will release hydrocarbon soils including fats, greases, oils, and sugars without
reacting with the cleaning surface. SC-Multi-Surface Cleaner is based on our most
powerful cleaning chemistry, SC-1000 Aqueous Cleaner, which and meets USDA
requirements for use in food processing. SC-Multi-Surface Cleaner and may be
used on both indoor and outdoor surfaces and complies with:
USEPA Design for the Environment (DfE)
USDA BioPreferred® Program
USDA A1 General Cleaning & L1 Drain/Sewer Acceptable
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
NSN 6850-01-505-7193 (5 gal.); 6850-01-505-7187 (55-gal.); 6850-01-505-7185
(bulk)
INSTRUCTIONS: For best results, rinse surface to remove excess soil before cleaning.
For heavy soil, apply product and let stand for 1 - 2 minutes before agitating with a
nylon brush or other scrubber. For normal to light cleaning, may be applied using
spray bottle, sponge or mop. Increased dwell time will reduce cleaning effort or the
need to agitate.Thoroughly rinse with water to remove soil, avoid streaking and leave
surface residue free. May be use on all “water- safe” surfaces including tile, vinyl,
walls, laminates, marble and plexiglass.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT
CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, very light amber liquid
Odor: Mild surfactant
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.002
Relative Density: Greater than water
pH Range: 9.5 – 9.9
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform
their own test(s) to determine the suitability of the
product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-ActiSolv Safety Solvent
DESCRIPTION: SC-ActiSolv is a low volatile, fatty alcohol solvent derived from renewable plant-based resources.
SC-ActiSolv may be used in a variety of cleaning applications including polymerized lubricants,
fuels, acrylic and oil-based paints, printing inks and coatings. SC-ActiSolv may also be used as a
co- solvent or solvent additive in non-ionic surfactant solutions for heavy-duty degreasing.
Highly water-miscible, SC-ActiSolv may be free rinsed with hot or cold water and is intended to
loosen hardened hydrocarbon soils. SC- ActiSolv is chemically non-reactive, storage stable and
highly reusable for several weeks in conventional solvent recovery machines, ultrasonic
degreasers and hand operations. SC-ActiSolv complies with:
USDA BioPreferred® Program
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
US DOT: Class 55, Liquid Cleaning Compounds
SC-ActiSolv is a powerful replacement for:
Xylene
Toluene, Methyl benzene
Methyl Chloride
Stoddard
Glycol Ethers, Butyl Cellosolve
INSTRUCTIONS: SC-ActiSolv may be sprayed on or applied with a cloth. Depending on the soil, allow the product
to dwell before wiping soil from the cleaning surface. SC-ActiSolv may be used full-strength or
diluted with water depending on the specific application. When water is added, SC-ActiSolv will
become more of a release agent and less of a solvent. Suggest a water rinse to remove soil and
residual product.
Suggested Dilutions: Heavy Cleaning 100% - 50%
Average Cleaning 50% - 20%
Routine Maintenance 10% - 2%
Note: SC-ActiSolv will melt virgin acrylic and should not be exposed to acrylic resins.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, pale yellow liquid
Odor: Slight detergent odor
Water Solubility: 100%
Boiling Point: 120ºC (248ºF)
Flash Point: 78.9ºC (174ºF)
Specific Gravity: 1.060
Relative Density: Greater than water
pH: 9.7
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-Carpet & Upholstery Spotter & Shampoo
DESCRIPTION: SC-Carpet & Upholstery Spotter & Shampoo is comprised of non-ionic surfactants and a water
hardness modifier to create a powerful micelle cleaning action that can tolerate tremendous soil
loads. SC-Carpet & Upholstery Spotter & Shampoo penetrates and lifts hydrocarbon soils
including fats, oils, greases, proteins and sugars without damaging carpeting fibers or
upholstery fabrics or their backing and substrate materials. Because SC-Carpet & Upholstery
Spotter & Shampoo is most effective on organic soils, it is not recommended for use on items
that have been dyed with “natural” colorants.
SC-Carpet & Upholstery Spotter & Shampoo complies with:
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
USDA BioPreferred® Program
INSTRUCTIONS: For best results, SC-Carpet & Upholstery Spotter & Shampoo should be used with extraction
equipment. Recommend pre-testing product on “dry-cleaning only” items before application.
Spotting: Scrape hardened soil such as dried food, dirt or chewing gum before applying product
full strength to spots. Product may be applied with a spray bottle. For best results, agitate with
a nylon brush and allow 5 – 10 minutes of dwell time before extraction cleaning. It is important
to remove all residual product with a water rinse to prevent re-soiling.
Shampooing: Follow manufacturers recommended dilution schedule for preparing cleaning
solution in extraction machines. Generally 1% (1 oz. per gallon) of SC-Carpet & Upholstery
Spotter & Shampoo is adequate for warm water extraction. For best results, rinse all areas after
shampooing with warm water.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, very light amber liquid
Odor: Mild surfactant
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.004
Relative Density: Greater than water
pH Range: 10.2 – 10.5
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-EZ-Solv Safety Solvent
DESCRIPTION: SC-EZ-Solv Safety Solvent is an ideal non-evaporative all purpose, non- toxic solvent where
dwell time and continuous reusability are important. Comprised of soy ester and corn fatty
alcohol, SC-EZ-Solv has a KB value of 1000+ and non-reactive with most cleaning compounds.
SC-EZ-Solv is not water miscible and is an ideal solvent for removing gum adhesives, organic
resins, polyurethane, silicone, latex and acrylic paints, permanent markers and polymerized
hydrocarbon soils. SC-EZ-Solv complies with:
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
USEPA Design for the Environment Program (DfE)
USDA BioPreferred® Program
BAC 5750 Rev. L Solvent Cleaning of Metals
US DOT: Class 55, Liquid Cleaning Compounds
SC-EZ-Solv is a powerful replacement for:
Xylene
Toluene, Methyl benzene
Methyl Ethyl Ketone
Glycol Ethers, Butyl Cellosolve
Kerosene, Mineral Oil
INSTRUCTIONS: SC-EZ-Solv may be spray applied, or applied by a cloth, and allowed to dwell before being wiped
from the cleaning surface. When removing graffiti or adhesive from painted surfaces, care must
be taken to wash the SC-EZ-Solv from the surface after removal of the soil in order to prevent
further solvating of the surface. SC-EZ-Solv will react with polystyrene, polysulphates, and
acrylics, while prolonged exposure will cause some types of rubber, PVC, EPDM and ABS to
become softened over time. SC- EZ-Solv also works effectively in ultrasonic cleaners and
automatic parts washers.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, slightly viscous light yellow liquid
Odor: Distinctive
Water Solubility: Not water soluble
Boiling Point: 144.4ºC (292ºF)
Flash Point: 65.5ºC (150ºF)
Specific Gravity: 0.946
Relative Density: Less than water
pH Range: 6.9 of water dispersion
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-Floor & Tile Cleaner
DESCRIPTION: Based on our proprietary formulation, SC-Floor & Tile Cleaner brings state-of-
the-art surfactant technology to industrial cleaning. SC-Floor & Tile Cleaner is a
concentrated cleaning solution proven to effectively clean floors including ceramic
tile, vinyl, polyresin, linoleum, and marble. SC-Floor & Tile Cleaner does not contain
harmful caustics, which cause damage to grout and the floor finish. SC-Floor & Tile
Cleaner complies with:
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
USEPA Design for the Environment Program
USDA BioPreferred® Program
INSTRUCTIONS: Use warm water, if possible, and mop or machine-wash as usual.
For dried on soil such as food or chewing gum scrape up as much as possible before
pre-treating with full-strength SC-Floor & Tile Cleaner. Allow product to dwell for 5 -
10 minutes, then agitate with a nylon brush and mop as usual. For soiled grout, let
solution stand for 5 minutes before scrubbing grout with a stiff bristle brush. For
best results, rinse with clean water to remove soil and residual product.
Dilution Ratios: 1:40 for light (routine) cleaning
1:20 for cleaning kitchen grease and oil
1:10 for heavy traffic areas
1:5 for grout cleaning
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT
CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, very light amber liquid
Odor: Mild surfactant
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.004
Relative Density: Greater than water
pH Range: 10.2 – 10.5
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform
their own test(s) to determine the suitability of the
product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-Graffiti, Tar & Gum Remover
DESCRIPTION: Derived from 100% plant-based materials, SC-Graffiti, Tar & Gum Remover effectively
removes most organic and inorganic soils without harming the cleaning surface. SC-
Graffiti, Tar & Gum Remover is a powerful non-evaporative solvent intended to
loosen tough soils such as tar, chewing gum, permanent marker, ink and graffiti
paints. SC- Graffiti, Tar & Gum Remover complies with:
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
USEPA Design for the Environment Program (DfE)
SDA BioPreferred® Program
SC-Graffiti, Tar & Gum Remover is a powerful replacement for:
Xylene
Toluene, Methyl benzene
Methyl Ethyl Ketone
Glycol Ethers, Butyl Cellosolve
Kerosene, Mineral Oil
INSTRUCTIONS: When removing grease, tar, gum, or similar materials from carpeting or upholstery
fabrics, begin by scraping off any loose material with the edge of a spatula-like tool.
Apply a small amount of SC-Graffiti, Tar& Gum Remover and allow to dwell for 5 to
10 minutes before agitating with a nylon brush. For best results, rinse soil and
residual product with an aqueous cleaning solution. Warning: Pre-test small
inconspicuous area before applying. SC-Graffiti, Tar & Gum Remover should
not be left on surfaces for a prolonged period of time because it will remove most
paints or may damage some acrylic surfaces.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, slightly viscous light yellow liquid
Odor: Distinctive, mild
Water Solubility: Not water soluble
Boiling Point: 144.4ºC (292ºF)
Flash Point: 65.5ºC (150ºF)
Specific Gravity: 0.946
Relative Density: Less than water
pH Range: 6.9 with water dispersion
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform
their own test(s) to determine the suitability of the
product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-Grease Trap & Drain Cleaner
DESCRIPTION: SC-Grease Trap & Drain Cleaner is intended for grease trap maintenance to solubilize
fats, eliminate odors, and keep drain pipes clean of accumulated fats. SC-Grease Trap
& Drain Cleaner is a combination of our powerful SC-1000 cleaning chemistry with
biodigesters called bacillus septillus in spore form. When used for routine
maintenance, SC-Grease Trap & Drain Cleaner effectively removes food greases
and paraffins without damaging equipment and pipes like hazardous caustics or
solvents. SC-Grease Trap & Drain Cleaner complies with:
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
USEPA Design for the Environment (DfE)
USDA BioPreferred® Program
INSTRUCTIONS: If a grease trap is already impacted by fatty effluent and organic matter, it may be
necessary to completely clean the tank and waste lines back to the sanitary discharge
unit. If calcites have built-up over time, it may be necessary to do an acid wash with
SC-OmniBrite Acid before using SC- Grease Trap & Drain Cleaner. Thereafter, use 1
gallon of SC-Grease Trap & Drain Cleaner per 10-gallon capacity and let stand for 20
minutes by blocking off the drainpipe exit. Drain the tank and rinse thoroughly. For
drain cleaning, block downstream drain and back fill floor drain system with a hose
attached to the hot water supply until floor drains begin to back up at floor level.
Add 8 ounces of SC-Grease Trap & Drain Cleaner at each floor drain, sink drain and
drain inlets; allow to dwell overnight; then drain. To maintain a "healthy" bio
environment, pour 8 oz. of SC-Grease Trap & Drain Cleaner into each drain every day
until the grease trap remains free of organic build-up then reduce to once a week for
routine maintenance.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, slightly viscous very light amber liquid
Odor: Mild surfactant
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.009
Relative Density: Greater than water
pH Range: 10.2 – 10.5
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-Kitchen Exhaust Hood & Filter Cleaner
DESCRIPTION: SC-Kitchen Exhaust Hood & Filter Cleaner is a low foaming, highly concentrated,
non-ionic surfactant system that removes the toughest kitchen soils such as cooking
fats, without harming the cleaning surface or kitchen equipment. Soils are easily
removed by applying SC-Kitchen Exhaust Hood & Filter Cleaner to the warm surface
either sprayed, wiped, or dipped in a warm solution for several minutes in order
to loosen soils before washing away. SC- Kitchen Exhaust Hood & Filter Cleaner ,
based on our SC-1000™ formulation, will also help to minimize cooking odors. This
product is specified for Garland Commercial and VentMaster Kitchen exhaust hoods
and complies with:
USDA A1 General Cleaning & L1 Drain/Sewer Acceptable
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
USEPA Design for the Environment (DfE)
USDA BioPreferred® Program
INSTRUCTIONS: Apply directly to hood surfaces with wet sponge or terry cloth and agitate as
necessary. Rinse with warm water and air dry before using underneath cooking
surfaces. Filters should be placed in deep sink with approximately 8 oz. of SC-Kitchen
Exhaust & Filter Cleaner to 5 gal. of hot water (110°F); allow to soak overnight to
reduce cleaning effort; shake excess solution free and air dry before reinserting over
cook surfaces.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT
CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, slightly viscous, very light amber
liquid
Odor: Mild surfactant
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.009
Relative Density: Greater than water
pH Range: 10.2 – 10.5
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform
their own test(s) to determine the suitability of the
product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-Laundry Stain Remover & Pre-soak
DESCRIPTION: Based upon the powerful cleaning performance of colloidal micelles, SC-Laundry
Stain Remover gently solubilizes fats, greases, oils, lipids, proteins and sugars without
the use of harsh toxic chemicals. SC-Laundry Stain Remover does not contain free
caustics, bleach, artificial brighteners, ammonia, aldehydes, synthetics or phosphates
and will not harm the ozone layer or causing eutrophication in waterways.
SC-Laundry Stain Remover complies with:
USEPA Design for the Environment (DfE)
USDA BioPreferred® Program
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
INSTRUCTIONS: Apply SC- Laundry Stain Remover directly to the stain surface and knead stain
between fore-finger and thumb before placing in regular laundry cycle or allow to
soak for several hours in a shallow sink or soaking tub of warm water, followed by
regular laundry cycle.
Not recommended for “Dry Clean Only” fabrics when water-based solutions may be a
problem. Certain synthetic dyes such as: USDA Red #5, Yellow #5 and Red #3 may not
be removed by SC-Laundry Stain Remover.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT
CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, very light amber liquid
Odor: Mild surfactant
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.004
Relative Density: Greater than water
pH Range: 10.2 – 10.5
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform
their own test(s) to determine the suitability of the
product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-Magic Pan Hand Dishwashing Liquid
DESCRIPTION: SC-Magic Pan does not rely on traditional reagent cleaning chemistries but
rather the powerful cleaning action of micelle technology: hyperactive sub-molecular
particles that churn up soil and gently lift it from the cleaning surface. With this
powerful micelle technology, even a small amount of SC-Magic Pan solution will
solubilize the toughest food soils, including fats, greases, oils, lipids, proteins and
sugars. SC-Magic Pan complies with:
USEPA Design for the Environment (DfE)
USDA BioPreferred® Program
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
INSTRUCTIONS: Recommend scraping off heavy food soils before pre-soaking. For best results, use
hot water (130° F) with 1 oz. of product per 1 gal. of water and let soak for 10-15
minutes. Apply full strength to a sponge for scrubbing off heavy food waste. Rinse
thoroughly with warm water and air dry. Maybe used on oven racks and other
cooking items and equipment; use full strength, overnight for easier cleaning.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT
CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, viscous, light yellow liquid
Odor: Mild detergent
Water Solubility: 100%
Boiling Point: 100.5ºC (213ºF)
Flash Point: None
Specific Gravity: 1.030
Relative Density: Greater than water
pH Range: 8.0 – 8.2
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform
their own test(s) to determine the suitability of the
product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-MaxiSolv Safety Solvent
DESCRIPTION: SC-MaxiSolv is a 100% water miscible, moderately evaporative solvent that can replace hazardous
volatile products for general industrial cleaning. An organic solvent with low flammability risk,
SC-MaxiSolv will not react with other cleaning compounds, and is an effective co-solvent. SC-
MaxiSolv has a Kauri Butinal (KB) value estimated at 1,000+ and is appropriate for precision
cleaning applications where the surface being cleaned needs to be left dry, without any residual
product or requiring a further cleaning step.
SC-MaxiSolv is a suitable release agent for removing:
• Industrial resins, silicone oils and greases, epoxies, and lubricants
• Metalworking fluids, coolants, fats, oils, and lithium greases
• Printing layout inks
• Carriers of oils, lubricants, and coatings
REGULATIONS:
SC-MaxiSolv complies with:
• OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
• USEPA 600, 4-90, 027 for aquatic toxicity
• USEPA 601 & 602 for VOC testing
• USDA BioPreferred® Program
• SNAP for precision and electronics cleaning
• US DOT: Class 55, Liquid Cleaning Compounds
SC-MaxiSolv is a powerful replacement for:
• 1,1,1-Trichloroethane, TCA
• Trichloroethylene, TCE
• Acetone
• Toluene, Methyl benzene
• Perchlorochylene
• Glycol Ethers, Butyl Cellosolve
EQUIPMENT: In most cases, SC-MaxiSolv may be used as a direct replacement for hazardous evaporative
solvents without changing equipment or procedure. Although SC-MaxiSolv is safe to use, it is
recommended that equipment should be designed to handle flammable or combustible liquids.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, very light yellow, slightly viscous liquid
Odor: Strong solvent
Water Solubility: 100%
Boiling Point: 309ºF (154ºC)
Flash Point: 145°F (62.8°C)
Specific Gravity: 1.034 (Water = 1)
Vapor Density: 4.07 (Air = 1)
pH Range: Not determined
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-More Than Glass Cleaner
DESCRIPTION: SC-More Than Glass Cleaner may be used on glass, acrylic finishes, plastic
laminate surfaces, ceramic tile, porcelain, bright metals, and chrome. SC-More Than
Glass is a blend of non-ionic surfactants, corn ethyl lactate and ethanol additives
specifically selected to eliminate residue and improve flash drying while providing an
antistatic effect to reduce soiling. SC-More Than Glass does not contain ammonia or
other toxic volatiles, and will not stain or leave streaks. Continuous use of SC-More
Than Glass will not harm rubber or vinyl, and will leave these surfaces free of
oxidants. SC-More Than Glass complies with:
USEPA Design for the Environment Program (DfE)
USDA BioPreferred® Program
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
INSTRUCTIONS: SC-More Than Glass Cleaner is available in ready-to-use and concentrated
formulations. For concentrate dilute 1 part SC-More Than Glass Concentrate to 9 parts
water. Low-foaming formula can be used in pressure washers for outdoor window
washing and surface cleaning. SC-More Than Glass Cleaner Concentrate may be used
with hose attachments for cleaning exterior windows. Apply ready-to-use
formulations with spray bottle and wipe with clean, lint-free cloth.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT
CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, light blue water-like liquid
Odor: Mild surfactant
Water Solubility: 100%
Boiling Point: 90ºC (194ºF)
Flash Point: None
Specific Gravity: 0.992
Relative Density: Greater than water
pH Range: 8.1 – 8.4
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform
their own test(s) to determine the suitability of the
product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-Odor-Ex Cleaning Deodorizer
DESCRIPTION: SC-Odor-Ex Cleaning Deodorizer is a concentrated cleaning solution proven to
eliminate odors while cleaning. A blend of our odor neutralizer and non-ionic
surfactant system, SC-Odor-Ex Cleaning Deodorizer does not cover up odors with a
masking fragrance, but breaks the odor-causing chemical compound. SC-Odor-Ex
Cleaning Deodorizer is safe to use on all “water-safe” surfaces such as carpeting,
upholstery fabrics, painted walls, laminate counters, and stainless steel. Ideal product
applications include trash compactors, holding tanks, animal kennels, institutional
laundries and treating smoke damage. SC-Odor-Ex Cleaning Deodorizer complies
with:
USEPA Design for the Environment (DfE)
USDA BioPreferred® Program
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
INSTRUCTIONS: SC-Odor-Ex Cleaning Deodorizer may be used full strength or diluted with water
depending on the specific application. The product may be applied using a sprayer or
sponge, agitate if necessary and for best results, rinse with water to remove soil and
residual product.
Suggested Dilutions: Trash Compactors/Receptacles 100% - 20%
Hard Surface Cleaning 20% - 10%
Carpet & Upholstery Cleaning 5%
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT
CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, colorless water-like liquid
Odor: Mild ozone or peroxide
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.002
Relative Density: Around water
pH Range: 7.8 – 8.1
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform
their own test(s) to determine the suitability of the
product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-Odor-Ex Odor Neutralizer
DESCRIPTION: SC-Odor-Ex Odor Neutralizer is a true odor destroyer that eliminates unpleasant
odors on contact. Derived from 100% plant- based ingredients, SC-Odor-Ex Odor
Neutralizer works by breaking key chemical bonds such as sulfur, ammonia, hydrogen
sulfide, and butyl mercaptan so that they are not detectable by smell. Unlike
masking agents that simply cover up odors with a more pleasant fragrance, SC-Odor-
Ex Odor Neutralizer reacts chemically with the odor compound by a process called
oxidation. This oxidation converts the odiferous chemical to a new compound that
has no odor. SC-Odor-Ex Odor Neutralizer is effective for institutional use, food and
beverage processing, and agricultural applications.
SC- Odor-Ex Odor Neutralizer complies with:
USEPA Design for the Environment (DfE)
USDA BioPreferred® Program
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
INSTRUCTIONS: SC-Odor-Ex Odor Neutralizer is safe to use on all soft and hard “water-safe” surfaces,
however, we suggest testing in an inconspicuous area before application. Use
product full-strength and spray 12'' to 18" from surface directly on the odor source
until the surface is lightly damp; it is not necessary to saturate the area. For odors
caused by liquid sources it may be necessary to reapply because the product is
absorbed into liquid-based odor. For large- scale applications, atomize into air using
a fogging system, approximately 1 gal. per 5,000 s.f. (450 m²).
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT
CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, colorless water-like liquid
Odor: Mild ozone or peroxide
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.002
Relative Density: Around water
pH Range: 7.8 – 8.1
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform
their own test(s) to determine the suitability of the
product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-OmniBrite Acid Cleaner
DESCRIPTION: SC-OmniBrite Acid Cleaner is a ready-to-use 100% plant-based formulation
comprised of fatty acids, a unique plant enzyme, non- ionic surfactants and a
buffering system. With a low acid reserve of 9, SC-OmniBrite Acid is not corrosive to
skin making it safe to handle and dispose of. SC-OmniBrite Acid is appropriate for
removing accumulated calcium build-up on metal pipe, elastomeric and vitreous
ceramic surfaces such as aluminum fin coil heat exchangers, circulation pipes, dairy
process equipment, toilets & urinals, beverage machines, and surfaces with hard
water accumulation. SC-OmniBrite Acid Cleaner complies with:
USEPA Design for the Environment (DfE)
USDA BioPreferred® Program
EU REACH Pre-registered
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
INSTRUCTIONS: Apply SC-OmniBrite Acid full strength or depending on the application, SC-
OmniBrite Acid may be diluted with water. Typical solution strength is 1:10 parts
water (10%) solution. Allow product to dwell on soil for 30 minutes up to 2 hours. If
necessary agitate with a nylon brush or sponge before thoroughly rinsing with clean
water. The water rinse is important for removing soil and neutralizing any residual
product.
Suggested Dilutions: Difficult Cleaning 100% - 50%
Average Cleaning 50% - 10%
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, water-like liquid
Odor: Slight detergent
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.034
Relative Density: Greater than water
pH Range: 1.8 – 2.5
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-Oven & Grill Cleaner
DESCRIPTION: SC-Oven & Grill Cleaner is an industrial strength non-ionic linear alcohol surfactant
system, based on our SC-1000 formulation which penetrates and lifts hydrocarbon
soils such as fats, oils, greases, proteins and sugars without damaging the cleaning
surface. SC-Oven & Grill Cleaner cuts through organic soils without any dangerous
chemicals or caustic fumes and does not require the use of protective clothing or
gear. The SC-Oven & Grill Cleaner formulation does not contain abrasives, caustics or
CFCs and complies with:
USEPA Design for the Environment (DfE)
USDA BioPreferred® Program
USDA A1 General Cleaning & L1 Drain/Sewer Acceptable
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
INSTRUCTIONS: Apply SC-Oven & Grill Cleaner directly to grill or oven surface; and allow 3 - 5 minutes
of dwell time before agitating with a scrubber or brush, then rinse thoroughly with
warm water. For heavy soil such as baked on grease and fat, spray apply at full
strength and dwell in warm oven (110°F) for 10 - 15 minutes, then agitate and rinse as
indicated. Increased dwell time (20 minutes) should reduce the scrubbing effort.
Dilution Ratio: Baked-On Heavy soil: 100% - 50%
Average Soil: 20% - 10%
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT
CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, very light amber liquid
Odor: Mild surfactant
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.009
Relative Density: Greater than water
pH Range: 10.2 – 10.5
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform
their own test(s) to determine the suitability of the
product for their specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-Premium Laundry Detergent
DESCRIPTION: SC-Premium Laundry Detergent is a dramatic departure from traditional salt-based detergents
that use artificial foam builders, dyes, fragrances and thickeners, which can irritate skin and
cause allergic reactions in chemically sensitive people. Based upon plant esters from apples, oats,
corn, and soy, SC-Premium Laundry Detergent is based on a non-ionic surfactant system for
loosening and removing organic soils without damaging fibers. SC-Premium Laundry Detergent
also contained a protein allergen neutralizer, referred to as our EX formulation, which has been
proven effective against protein allergens from dust mite droppings, dog dander and cat saliva.
SC-Premium Laundry Detergent does not contain caustics or phosphates and complies with the
following:
USEPA Design for the Environment (DfE)
USDA BioPreferred® Program
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
INSTRUCTIONS: Recommend using warm water (90°F), however, cold water is also effective.
SC-Premium Laundry Detergent will remove organic soils, however certain synthetic dyes
such as: USDA Red #3 & #5, and Yellow #5 may not be removed as effectively. Use as with other
liquid laundry detergents by
pouring into cycle dispenser of washing machine in the following
proportions:
Large load 4 ounces (120ml)
Medium load 2 ounces (60 ml)
Small load 1 ounce (30 ml)
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, viscous, yellow liquid
Odor: Slight detergent
Water Solubility: 100%
Boiling Point: 100ºC (212ºF)
Flash Point: None
Specific Gravity: 1.010
Relative Density: Greater than water
pH Range: 10.1 – 10.3
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-SuperSolv Safety Solvent
DESCRIPTION: SC-SuperSolv is a non-evaporative solvent that safely removes most organic and inorganic
soils without damaging the cleaning surface. With a Kauri Butinol (KB) value estimated in
excess of 150, SC-SuperSolv removes lubricants, brake fluid, engine oil, lithium grease, paint,
permanent marker, and certain adhesives. SC-SuperSolv is non-aromatic and contains no ozone
depleting chemicals. SC-SuperSolv is an organic, antioxidant solvent that will not harm most
plastics, vinyl, nylon, butene, rubber, ferrous metals or natural fibers. SC-SuperSolv is water
miscible and works effectively in ultrasonic cleaners and automatic parts cleaners. SC- SuperSolv
complies with:
USEPA Design for the Environment (DfE)
USDA BioPreferred® Program
EU REACH Pre-registered
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
US DOT: Class 55, Liquid Cleaning Compounds
SC-SuperSolv is a powerful replacement for:
1,1,1-Trichloroethane, TCA
Toluene, Methyl benzene
Methyl Chloride
Glycol Ethers, Butyl Cellosolve
Trichloroethylene, TCE
Perchlorochylene
Stoddard Solvent
INSTRUCTIONS:
SC-SuperSolv is a powerful solvent and should be pre-tested prior to use especially on soft
metals. SC-SuperSolv may be used full-strength or diluted with water depending on the specific
application. When water is added, SC- SuperSolv will become more of a release agent and less of
a solvent. SC- SuperSolv may be spray applied, or applied by a cloth, and wiped from the
cleaning surface. Less product may be necessary with increased temperature, dwell time and/or
agitation. Rinse thoroughly with water to remove soil and residual product.
Suggested Dilutions: Heavy Cleaning 100% - 50%
Average Cleaning 50% - 20%
Routine Maintenance 10% - 2%
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, viscous light amber liquid
Odor: Mild solvent
Water Solubility: 100%
Boiling Point: 136.6ºC (212ºF)
Flash Point: 82.2ºC (180ºF)
Specific Gravity: 1.018
Relative Density: Greater than water
pH Range: 10.2 – 10.4
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SAFE CARE® Steel Bright Polish
DESCRIPTION: SAFE CARE® Steel Bright Polish is a blend of vegetable oils along with a plant-based
solvent to create a unique compound that cleans while it leaves a “like-new” finish.
SC-Steel Bright is a food grade cleaner designed for use on stainless steel and most
other metal surfaces such as chromium, aluminum, zinc, mild steel, brass, copper and
silver. A light application of SC-Steel Bright will leave a protective coating to help
retard tarnishing and restores the metal surface to a brilliant shine without hard
rubbing and polishing.
SC- Steel Bright is an ideal replacement for traditional petroleum-based mineral oil
cleaners or polishing agents.
SC-Steel Bright complies with:
USDA BioPreferred® Program
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
INSTRUCTIONS: Recommend cleaning the surface from heavy soils using warm water and a non-
caustic surfactant such as SC-Stainless Steel Cleaner before application. The surface
should be dry before applying SC- Steel Bright. Smoothly apply to the surface with a
clean soft cloth in the direction of the grain. To avoid bubbles or haze, do not wipe.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT
CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, viscous amber liquid
Odor: Vegetable oil
Water Solubility: 0%
Boiling Point: >304ºC (580ºF)
Flash Point: >150ºC (300ºF)
Specific Gravity: 0.88
Relative Density: Not tested
pH Range: Not tested
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
GEMTEK® Products
EXCLUSIVE DISTRIBUTOR ROMANIA:
Mobile: +40 730 35 35 05 | Tel./Fax: +40 269 23 20 02
e-mail: [email protected]
web: www.lewo.ro
SAFECARE® Industrial Cleaners, Solvents & Specialty Products
SC-SoyEster Safety Solvent
DESCRIPTION: SC-SoyEster is a powerful non-evaporative solvent that creates an effective release
agent for heavy grease, oil and tar, as well as organic and some inorganic inks. A
blend of soy methyl ester and other vegetable esters, SC-SoyEster is 100% plant-
based and ideal for cleaning tools, parts and equipment in the transportation and
printing industries. SC-SoyEster is not water-soluble and may be used with other
plant-based solvents and surfactant systems for more effective cleaning.
SC-SoyEster is low VOC and complies with:
USDA BioPreferred® Program
OSHA 29-CFR Ch. XVII 1910.1200 and 40 CFR Ch. 1, Subparts C & D
USEPA 600, 4-90, 027 for aquatic toxicity
USEPA 601 & 602 for VOC testing
US DOT: Class 55, Liquid Cleaning Compounds
SC-SoyEster is a powerful replacement for:
1,1,1-Trichloroethane, TCA
Trichloroethylene, TCE
Toluene, Methyl benzene
Glycol Ethers, Butyl Cellosolve
Kerosene, Mineral Oil
INSTRUCTIONS: SC-SoyEster may be spray applied, or applied by a cloth, and allowed to dwell
before being wiped from the cleaning surface. When removing ink, care must be
taken to rinse the residual SC- SoyEster from the surface to prevent further solvating.
It can be completely removed from the surface by rinsing with warm water or an
aqueous surfactant cleaning solution such as SC-1000 Aqueous Cleaner. SC-SoyEster
also works effectively in ultrasonic cleaners and automatic parts washers.
SAFE CARE® PRODUCTS ARE:
Non-toxic
Non-reactive
Non-carcinogenic
Readily biodegradable
Derived from renewable resources
Safe to use, store and dispose of
SAFE CARE® PRODUCTS DO NOT
CONTAIN:
Petroleum distillates
Glycol ethers
Terpenes
Synthetics
Builders & reagents
Caustics
BASIC PROPERTIES:
Appearance: Clear, slightly viscous yellow liquid
Odor: Light vegetable oil
Water Solubility: Not water soluble
Boiling Point: >204ºC (400ºF)
Flash Point: >149ºC (300ºF)
Specific Gravity: 0.88
Relative Density: Not tested
pH Range: Not tested
The information contained herein is believed to be correct
including test data conducted under controlled laboratory
conditions. Users of SAFE CARE products should perform their
own test(s) to determine the suitability of the product for their
specific application(s).
GEMTEK® Products