DM-1e SPEC.pdf

1.Before Starting

2.While Operating

•If you are under 18 please read manual (with a parent, guardian or a responsible adult if necessary).

•Any running area you choose must be dry. Do not run car near any water or wet dirt.

•Do not run on public streets. It is very easy to have the car run over or be damaged by hitting the curb.

•Do not operate the car in tight confined space. The car is very fast and will easily hit something.

•Do not run near people or animals. The car is very fast and could easily hit someone if you are not an expert driver.

•Do not operate the car at night. You will not be able to drive it safely.

3.Before Operating

•Make sure that all screws and nuts are properly tightened.

•Radio-Check battery life before running the car. If the radio does not have full control of the car with steering and/or throttle/brake, do not run until corrected. Failure to correct this will result in possible injury and damage to the car or property.

•Please confirm the neutral throttle trigger position.

4.Check Your Car After Running

•Turn OFF receiver first, then turn OFF transmitter. This will prevent the car from losing control.

•After running radio controlled car , it is necessary to perform routine maintenance.

5.Battery Safety

IMPORTANT-READ THIS BEFORE RUNNING

•Please be careful when handling the battery. It will be hot after running. If the wire is frayed, a short circuit can cause a fire.

TOOLS NOT INCLUDED IN THE KIT

Cutter

Curved Scissors

Craft Knife

Precision CaliperNeedle Nosed Pliers

Equipment Needed

Included Items

1.5mm Allen Wrench

2mm Allen Wrench

2.5mm Allen Wrench

OVERVIEW

Components

Transmitter

Parts Bag

Receiver

Radio Control Car

UM-3 Batteries( 8pcs )

Body Reamer

Instant CemmentScrew Cement

CAScrew Cement

GEARGREASE

Gear Grease

Cross Wrench

Turnbuckle Wrench

17mm Wheel Nut Tool

7.4V L

i-Po Battery(Hard Case)

L Battery Chargeri-Po

Servo

Brushless MotorBrushless Electric Speed Controller

40533FRONT AND REAR GEAR BOX

40538DIFF. CASE

40040CENTER DIFF. MOUNT PLASTIC PARTS

40721FRONT BUMPER

31304REAR UPRIGHT

40643SHOCK PLASTIC

Parts forNot Use

PLASTIC PARTS FOR USE

4071940719ARM HOLDER

40537REAR UPPER ARM

30663VELCRO BATTERY STRAPS

40720SIDE IMPACT BUMPER AND BODY POST

40539SERVO SAVER

SYMBOL USED THROUGHOUT THE INSTRUCTION MANUAL

EnsureFreeMovement

Ensure FreeMovement

ApplyGrease

Apply Grease

Oil

Tighten

Tighten

Do NotOver Tighten

RotateDirection

RotateDirection

Contact Adhesive

Contact Adhesive

Screw Cement

BAG

1:1

Parts Bag UsedDegrease WithMotor Spray

Do Not Over Tighten

Clockwise Rotation

Anti-clockwiseRotation

True-To-ScaleApply OilApply Screw Cement

40717 FRONT AND REAR LOWER ARM

40718FRONT KNUCKLE ARM

40716FRONT UPPER ARM

PLASTIC PARTS FOR USE

30662BATTERY CASE

1 ASSEMBLY OF THE FRONT SHOCKS

2 ASSEMBLY OF THE REAR SHOCKS

•Assemble 2 seets for front Step 1 Step 2 Step 3 Step 4

1.Pull down piston and pour oil into shock cylinder.2.To remove air bubbles by slowly moving piston up and down. 3.Pull down piston, attach pressure top and shock oil overflow with tissue paper.

0 20 30 4010

Fill the shocks with oil #80wt.

Step 5 Step 6

•Fit the o-ring into groove before assembly.

40633

40640

40636

Oil

40090

40090

400902mm

40090

400901mm

40634

40737

40736

2.6x5mm

40060

40638

2.6x5mm

30403

40643(Short)

CORRECT SHOCK ASSEMBLY

Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ball end and the shock is 14mm.

Do not over tighten as the plastic will strip.

Oil

•Be careful not to damage shock shaft.

Tighten

40643

40640

0 20 30 4010

40633

40640

40090

40090

400902mm

40090

400901mm

40634

40632

Step 3

2.6x5mm

40638

2.6x5mm

30403

40643(Short)

40054

40643

40090 2mm Washer

40090 1mm Washer

400903.5mm O-Ring

400907mm R-Ring

Step 6

40060

40751

.....x4

.....x2

.....x2

.....x2

Step 2*Assemble 2 seets for rear Step 1

40090 2mm Washer

40090 1mm Washer

400903.5mm O-Ring

400907mm R-Ring

.....x4

.....x2

.....x2

.....x2

Oil

OK

14

mm

1.Pull down piston and pour oil into shock cylinder.2.To remove air bubbles by slowly moving piston up and down. 3.Pull down piston, attach pressure top and shock oil overflow with tissue paper.

Oil

•Fit the o-ring into groove before assembly.

40636

Step 4

Fill the shocks with oil #60wt.

•Be careful not to damage shock shaft.

Step 5

Tighten

CORRECT SHOCK ASSEMBLY

Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ball end and the shock is 32mm.

Do not over tighten as the plastic will strip.

OK

32

mm

Step 1 Step 2

ASSEMBLY OF THE FRONT AND REAR DIFF.3

36053

40514

4x4mm

40538

40009

40513

40517(43T)

40009

40513

360538x16mm Ball Bearing

940344x4mmSet Screw

400102.5x13.8mm Pin .....x4

.....x4

.....x4

.....x2

40009P6 O-Ring

40514

36053

40010

4

.....x16

307764x10mmWasher

307734mmCross Pin .....x4

ASSEMBLY OF THE FRONT AND REAR DIFF.

Diff. Oil

40011

3x12mm30773

4002413x16x0.2mmShim .....x8

360538x16mm Ball Bearing .....x4

5 ASSEMBLY OF THE FRONT AND REAR GEAR CASE

5x4mm

40519

40533

40024

36053

4x35mm

40024

40516(13T)

36053 4x15mm

40533

40010

•Put the Diff. Oil #100000 for front and the #5000 for Rear•Fill the Diff. case to approx. 80% with the Diff. Oil

40513

30776

Step 1 Step 2

Step 1 Step 2

940203x12mmFlat HeadHex Screw

.....x8

940154x35mmHex Screw

.....x4


.....x4

Tight the diff screws in this order.

1

4

3

2

S r wc e

Cen

me t

Oil

Oil

Tighten

ApplyGrease

Builds two differentials for front and rear.

Builds two differentials for front and rear.

Builds two gear case for front and rear.

•Adjust the backlash with the shims.

3x12mm

ASSEMBLY OF THE SERVO SAVER

40719

7

ASSEMBLY OF THE SERVO SAVER8

.....x5

940413mmNylon Nut

405396x10mmPlastic Bearing .....x4

40511

3x10mm

40745

40539

ASSEMBLY OF THE SERVO SAVER

40563

40539

40034

40500(Black)

6

405394x8mmPlastic FlangeBushing

40037Steering Plat Hex Screw .....x2

.....x2

4002413x16x0.2mmShim .....x2

40539

40024

40037

40746

40539

40539

• Notice the direction of the servo saver connecting plate.

40719

.....x2

.....x2

40531Shock BallEnd Post

40531

3x25mm

40719

4x12mm

.....x5

Step 1 Step 2

Step 1 Step 2

3mm


900183x25mmCap Screw


.....x2

•Tighten the steering plate hex screw all way down and then back it off 1/2 turn.

EnsureFreeMovement

*Set the left and right hand side upper arm adjuster in the same direction.

Left Right

Oil

RotateDirection

Sr w

c eemn

Ce t

Sc e r wCem nte

re

Sc w

C m nte e

Screw

Cen

emt

40539

40539

3mm

40539

40539

ASSEMBLY OF THE STEERING TIE-ROD9

Step 1

10

Approx. 29.30 mm

1:1

Front

40533Front Plate Bed

.....x4400387mm Ball

.....x2

36700

36700

40038

40038

3x15mm

4x10mm

40548

36790

.....x2

405483mmNylon Nut(Thin Type)

.....x2

401263x6mm Flange Washer

40126

ASSEMBLY OF THE SERVO SAVER AND FRONT UPPER ARMS

.....x2

405253x48.1mm Arm Shaft

40719

3x12mm

4x12mm

40716(1mm and 3mm)

40716(2mm)

40719

Step 2

40525

40525


.....x2


.....x4


.....x2

*Insert the upper arm adjust into shock stay.

40716

Step 1

Assemble both right and left side.

Step 2

•Set the left and right hand side upper arms adjuster in the same direction.

Left Right

reSc

w Cement


11 ASSEMBLY OF THE FRONT SHOCK STAY

3x15mm

36742

35958

40719(A)

40719(B)

•Notice"L"make are for inside.

ASSEMBLY OF THE FRONT SHOCKS ONTO SHOCK STAY12

940413mmNylon Nut

940403x8mmWasher

40643Shock CapWasher .....x2

.....x2

.....x2

40643

3x8mm 3mm

3x12mm

ASSEMBLY OF THE REAR SHOCK STAY AND UPPER ARMS13

.....x2

368507mmBall

.....x2

.....x4

359585x8x2.5mmBall Bearing

36742Shock CapBushing


.....x2

940043x12mmHex Screw .....x2


.....x4

•Take the shock cap washer from the shock plastic tree.

EnsureFree

Movement

Do NotOver Tighten

Do NotOver Tighten

Step 2

11¡G

36850

36861

40537

40065

Approx. 12.5 mm

Step 1

Assemble both right and left sides.



3x10mm

4x12mm

40750


.....x2

14

ASSEMBLY OF THE REAR BRACE15

ASSEMBLY OF THE REAR UPPER ARMS

40716(2mm)

40716(1mm)

40546*Insert the caster angle adjuster onto arm shaft.

40719

40719

40719

4x16mm

4x12mm

40539

.....x2940114x16mmHex Screw

.....x240546 3x42.7mmArm Shaft

•Set the left and right hand side upper arms adjuster in the same direction.

Left Right



16

40539

4x15mm

ASSEMBLY OF THE ONE SPEED TRANSMISSION

Step 1 Step 2

35247 (47t)35248 (48t)35249 (49t) Stock

35219

40760

5X4mm

40120

36053

40759

6mm

940365x4mmSet Screw

.....x1

367436mm E-Ring

.....x1

Scr

ew

Ce

ntm

e

Clockwise

RotateDirection

17

18

19

ASSEMBLY OF THE ONE SPEED TRANSMISSION

ASSEMBLY OF THE ONE SPEED TRANSMISSION INTO THE CENTER MOUNT

ASSEMBLY OF THE ARM HOLDER ONTO CHASSIS

940365x4mmSet Screw

.....x2

367436mm E-Ring

.....x1

Step 1 Step 2

5x4mm

Scr

ew

Cem

ent

5x4mm

6mm

Scr

ew

Cem

ent

40120

36053

Step 1 Step 2

.....x2940344x4mmSet Screw


.....x4

40040

40040

40512

Step 3

3x10mm

40714

Do NotOver Tighten

40719

4x4mm

40719(Front/Front)

40719

4x16mm

40719

4x16mm

40719(Front/Rear)

40719(Rear/Front)

40719(Rear/Rear)

*set the arm holder adjuster to the same direction.

A A(Type A)

.....x8


•set the arm holder adjuster to the same direction.

A A(Type A)

40761

22

21

20

Step 1 Step 2

ASSEMBLY OF THE FRONT LOWER ARMS

40711

40711

4x10mm

3x18mm 3x8mm

40717

40719

3130840719

2mm

•A 3x8mm set screw is use for tighten or loose stabilizer.

(Left Side)

Center

•Keep stabilizer ball in the center. Turn stabilizer adjuster to adjust the stabilizer to the same angle.

Adjuster





Step 1 Step 2

ASSEMBLY OF THE REAR LOWER ARMS

40711

4x10mm

3x18mm

3x8mm

40717

40719

31308

40719 4x10mm

3x18mm

40719

3x8mm

40717

31308

40719

Center

•Keep stabilizer ball in the center. Turn stabilizer adjuster to adjust the stabilizer to the same angle.

Adjuster


2mm

•A 3x8mm set screw is use for tighten or loose stabilizer.




ASSEMBLY OF THE FRONT AND REAR GEAR BOX ONTO THE CHASSIS


.....x8

.....x2


.....x2

940413mmNylon Nut

.....x2


4x12mm

4x16mm

3x12mm

3mm

4x16mm

3x12mm

3mm

Step 1 Step 2

4x16mm

4x16mm

25

24

23

940344x4mmSet Screw

40526

36055

4x4mm

40521(Front)

36053

36053

.....x2

cw

S

reC

me

te

n

ASSEMBLY OF THE FRONT KNUCKLE ARMS

3690414mm Alum. Nut .....x4

3690314mm Steering Ball .....x4


40718(left)

36903

36903

40718

36904

40718

36904

L

Do NotOver Tighten

360552.5x16.8mm Pin .....x2


Step 1 Step 2•Notice the direction of the plastic washer.

5mm Allen Wrench

ASSEMBLY OF THE FRONT SUSPENSION ARMS Assemble both right and left sides.


940413mmNylon Nut

.....x2

.....x2

3x15mm

40126

3mm

•Put the drive shaft into cap joint before assembly.

2.5mm Allen Wrench

•When assembling the steering balls into the arms, leave about two threads for the upper arm, and leave no room for bottom arm.

ASSEMBLY OF THE FRONT PUSH RODS

30403

30403

4071240063

.....x4304036mm Ball



.....x2

40063

Approx. 34mm

1:1

� 34mm

Step 1 Step 2


3x20mm

3x12mm

28

27

26Assemble both right and left sides.

Step 1

ASSEMBLY OF THE REAR WHEEL HUB

3130711mmSteering Ball .....x4

31304

360552.5x16.8mm Pin .....x2


940365x4mmset screw

.....x2

31307

31305

31306

Step 2

Do NotOver Tighten

5x4mm

36082

36053

36055

40526

36053

8x12x1mm

EnsureFree

Movement Sc

ew

rC

emen

t

ASSEMBLY OF THE REAR SUSPENSION ARMS

.....x2

940413mmNylon Nut



3x25mm

3mm

*Insert the drive shaft before assembly.

34028

2.5mm Allen Wrench

•When assembling the steering balls into the arms, leave about one threads for the rear arm, and leave no room for front arm.

(Front)

(Rear)

ASSEMBLY OF THE REAR SHOCK ABSORBER Assemble both right and left sides.


.....x2

900183x25mmCap Screw

.....x2

40531Shock BallEnd Post

940403x8mmWasher

.....x2

3x20mm

40531

406433x8mm

3mm

3x25mm

.....x2

940413mmNylon Nut

31

30

29 ASSEMBLY OF THE TWO SPEED TRANSMISSION ONTO THE CHASSIS


.....x4

• Insert drive shaft into cap joint before center assembly onto chassis.

4x10mm

crew SCement

4x10mm

40762(90mm)

40762(97mm)

MOTOR INSTALLATION

.....x3


ASSEMBLY OF THE MOTOR MOUNT ONTO CHASSIS

101145mmEngine Mount Screw .....x2

10114 Do NotOver Tighten

Tighten the 10114 screwtemporary.

EnsureFree

Movement

Step detail

3x10mm

4x4mm

41202

Motor(Not Included)

30664-13t (stock)30665-14t30666-15t30667-16t30668-17t


Screw

C mente

4033

32EXTREMELY IMPORTANT

ADJUST MOTOR AND SPUR GEAR MAINTENANCE

Step 2Step 1

Step 3

Step 4

PUSH

PUSH

Tighten

•Adjust the motor mount position to get proper gear mesh.

•To get a perfect gear mesh , place a piece of notebook paper between the gears and tighten the motor mount screws.

•The spur gear may be damaged if the gear mesh is wrong.

3mm

Insert a notebook paper between spur gearand motor gear to make correct gear mesh.

PULL OUT

ASSEMBLY OF THE VELCRO STRAP INTO BATTERY CASE

30662

30663

Step 1 Step 2

Notebook Paper

Notebook Paper

Notebook Paper

34

35

36

ASSEMBLY OF THE ELECTRIC SPEED CONTROL ONTO BATTERY CASE

Electric Speed Control (Not Included)

•Use double side tapes.

ASSEMBLY OF THE WIRE BRIDGE ONTO BATTERY CASE AND RECEIVER BOX

3x10mm

30662

30662

30662

3x8mm

940023x8mmHex Screw

.....x2


.....x2

ASSEMBLY OF THE ELECTRIC SPEED CONTROL WIRE INTO RADIO CASE

Step 1 Step 2

*Route the speed control wire as picture shown.

*Route the speed control wire into receiver box.

38

37

39

ASSEMBLY OF THE STEERING SERVO ONTO RADIO CASE

940403x8x0.8mm Washer

.....x4


.....x4

3x10mm

3x8x0.8mm

30662B

3x10mm

3x8x0.8mm

ASSEMBLY OF THE STEERING SERVO WIRE INTO RADIO CASE

Electric Speed Control Wire

Steering Servo Wire

Steering Servo (Not Included)

ASSEMBLY OF THE RADIO CASE ONTO CHASSIS

3x10mm

4x10mm

3x10mm

4x12mm

Step 2Step 1

940264x12mmFlat Head Hex Screw

.....x1

940193x10mmFlat Head Hex Screw

.....x6

3x10mm

40 ASSEMBLY OF THE RECEIVER INTO RADIO BOX

940023x8mmHex Screw

.....x2

Step 2Step 1 Step 3

30662

3x8mm

Receiver(Not Included)

•Plug in your speed control wire and servo wire to your receiver.

37410

3066240642

30560

Antenna Wire

41

42

ASSEMBLY OF THE STEERING ROD ONTO RADIO BOX

•Approx. 16.6mm


.....x20 20 30 4010

Step 2Step 1

30411

37320

30401

30401

30411

3x12mm

Use the screwprovided withyour servo.

10769

30661

3x12mm

4x12mm

ASSEMBLY OF THE FRONT BUMPER

40721

40721


.....x3

.....x2


3x12mm

Tighten

Tighten

4mm

.....x3

940424mmNylon Nut

*Approx. 30.5 mm

1:1

40721

44

43

45

Step 1 Step 2

40721



.....x2

4x10mm

40117

•Approx. 4 mm

•The 4x10mm set screw is used to adjust down stop.

Completely Finished

Tighten



.....x2

.....x2



4x10mm

40725

3x12mm

ASSEMBLY OF THE REAR BUMPER

40721

4x12mm

40721


.....x2

.....x2


.....x2

940424mmNylon Nut

•Approx. 28.5 mm

1:1

3x12mm

4mm

Tighten

4x12mm

31159

31159

40117

Tighten

Tighten

Tighten

Tighten

17

Step 2

46 ASSEMBLY OF THE REAR BUMPER

4x12mm


4x10mm

31159

31159

40117

2.6x15mm

2.6x15mm

940542.6x15mmScrew

.....x2


.....x2

40721

Tighten

Tighten

Step 1

47


.....x2

4x10mm

3x12mm


.....x2

ASSEMBLY OF THE REAR BUMPER

•The 4x10mm set screw is used to adjust down stop.

•Approx. 3 mm

48

40117

40720

40117

40720

BATTERY INSTALL

Battery(Not Included)

8mm

15mm

•If use hard case battery , make a hole as picture shown.

Follow the manual instruction sprovided by ESC manufacturer to install the wire.

•Be aware of the direction of the battery.

Hard Case Battery

49

50

Step 1

ASSEMBLY OF THE WHEELS ONTO THE FRONT KNUCKLE AND REAR HUB

51

.....x440550Wheel Nut

•Tire and Wheel assembly.

40550

•Notice the direction of the tire pattern.

Assemble both right and left side.

86023 BLACK86024 BLUE86025 LIME86026 WHITE86027 ORANGE86028 GRAY

86059

86052 STOCK NO BELT86053 WITH BELT

86059

•Notice the direction of the tires.

INSTT

AN GLUE

(Right Hand Side)

Contact Adhesive

Contact Adhesive

Contact Adhesive

•Notice the direction of the tires. Make two the same for the left and 2 for the right. Check the rotation direction before gluing.

•Pull back the tire bead slightly and spot glue in four spots as shown. When dry, glue the rest of the wheel between the spots. Repeat the procedure on the other side of the wheel until fully glued.

ASSEMBLY OF THE TIRES AND WHEELS

Contact Adhesive

•Notice the direction of the tires.

(Left Hand Side)

MAKING HOLES AND CUTTING ON THE BODY SHELL

Step 2Step 1

Cut the body shelll as shown.

Wing Side Plate

31157

Left

Right

52

53

54 MAKING HOLES AND CUTTING ON THE WING

MAKING HOLES AND CUTTING ON THE BODY SHELL

MAKING HOLES AND CUTTING ON THE WING

Before making holes on the body, put the unpainted body on the chassisto confirm the mounting position and location for holes.

Step 1 Step 2

Make 9mm holes on the body shell as shown.

Make 4mm holes

Make 7mm holesBody Reamer (not included)

Make a 7mm hole

Make a 7mm hole

Make 3mm holes

Make 3mm hole

Make 3mm holes

Make 3mm hole

Wing Side Plate(L)

Wing Side Plate(R)

Step 1 Step 2

The position and the wing is the same.

Hole Position

Hole Position

Hole Position

55

56

57

WASH THE INSIDE OF THE BODY SHELL

Step 1 Step 2

Wash the inside of the body shell with mild detergent,and then rinse and dry thoroughly.

PAINTING BODY SHELL

Step 1 Mask the windows on the inside with masking tape.

Step 2 Paint the body with polycarbonate spray paints.

•When you have finished painting, peel off the external protective films.

•When the paint is dry, remove the masking.

ASSEMBLY OF THE WING ONTO THE BODY SHELL

Step 1 Step 2

.....x4

940413mmNylon Nut


3mm

3x5mm

Nylon Nut

Nylon Nut

Nylon Screw .....x2

.....x2

Nylon Nut

58 MOUNTING THE BODY SHELL

31159

31159

FRONT TOE-IN AND TOE-OUT SETTING

Firm rear suspension, over steering.Soft rear suspension, under steering.

FRONT AND REAR SHOCK ANGLE SETTING

Firm front suspension, less steering.Soft front suspension, more steering.

FRONT AND REAR CAMBER ANGLE SETTING

- -- -+ ++ +

Turnbuckle

SETTING GUIDE

NegativeNegative PositivePositive

12 Soft Firm

12Soft Firm

Adjust the length of the front steering rod to change the toe angle.

Making the steering rod longer will make the front tires become toe-in.Response will be slower and will over steer. Making the steering rod shorter will make the front tires become toe-out.Response will be quicker and will under steer.We recommended adjusting the front toe-out to 1.5 degrees. Adjust the length of the rear hub (12mm ball/rear) to change the toe angle.

Making the 12mm ball longer will make the rear tires toe-in.Response will be under steer.

Making the 12mm ball shorter will make the rear tires toe-out. Response will be over steer. We recommended adjusting the rear toe-in to 2 degrees.

Use a 2.5mm allen wrench to adjust toe-in for front and rear.

(Front)

(Rear)

Note: Place the model car on a flat surface. Raise the chassis to it's maximum clearance before the wheels leave the ground. Adjust the length of the front and rear upper arms so that the wheels are right angles to the ground.

The front camber adjustment can be made by moving the 14mmsteering ball at the front upper arms on knuckles, clockwise or anticlockwise.

We suggest using 1.5 degrees of negative camber for the front.

(FRONT)

(FRONT)

(REAR)

(REAR)

Adjust the length of the turnbuckle on can be change the rear camber.

We suggest using 2 degrees of negative camber for the rear.

the rear upper arms

•Use 2.5mm hex wrench to adjust upper arm ball in front.

TOE-INTOE-OUT

NEUTRAL POSITION

Steering Rod

REAR TOE-IN

2.5mm Allen Wrench

TOE-OUT

REAR TOE-IN

Soft

Firm

12

1 2 3 4Soft Firm

OFNA DESCRIPTIONS RETAIL OFNA DESCRIPTIONS RETAIL10114 ENGINE MOUNT SCREWS,FLAT HEAD 7.95 40511 SERVO SAVER SPRING POST 6.9510769 SERVO SAVER INSERTS,BLK ALL RADIO 0.99 40512 CENTER DIFF. MOUNT POST 13.9530401 STEERING ENDS, PLASTIC 6 PCS. 2.95 40513 DIFF. GEAR (small & large)ALUM 16.9530403 6mm BALL, STEEL (NO COLLAR) 4.95 40514 CAP JOINT FOR DIFF. 13.9530411 6mm BALLS w/COLLAR,STEERING 6P 4.95 40516 STEEL SMALL BEVEL GEAR 13T 14.9530560 ANT TUBE AND MOUNT 2.95 40517 STEEL BEVEL GEAR 43T 38.9530662 BATTERY CASE,RX BOX LX-1e 19.95 40519 CAP JOINT, CENTER PINION GEAR 9.9530663 BATTERY VELCRO STRAPS LX-1e 9.95 40521 UNIVERSAL JOINT, FRONT 44.9530664 PINION 13T 5MM SHAFT 12.95 40525 SHAFT 3x48.1mm DM UPPER FRONT 6.9530665 PINION 14T 5MM SHAFT 12.95 40526 WHEEL HUB 17MM 11.9530666 PINION 15T 5MM SHAFT 12.95 40531 SHOCK BALL POST/ONE-PIECE/TOP 9.9530667 PINION 16T 5MM SHAFT 12.95 40533 GEAR CASE 11.9530668 PINION 17T 5MM SHAFT 12.95 40537 UPPER ARMS 6.9530773 CROSS PIN AXLES, 4mm STEEL 3.95 40538 DIFF CASE F&R 9.9530774 CROSS PIN AXLES, 4mm ALUM 6PCS 9.95 40539 PLASTIC SERVO SAVER & CNT BRAC 11.9530776 WASHER, 4x10x0.2mm 4PCS. 1.95 40546 FRONT ARM SHAFT 3x42.7mm 11.9531140 BODY, C-TYPE WITH DECALS 64.95 40548 NUT M3 NYLON (Thin Type) 1.9531141 BODY, M-TYPE CLK DECALS/MASK 64.95 40550 WHEEL NUT 17mm LX-2 4.9531144 BODY, V-GTP WITH DECALS 59.95 40632 SHOCK BODY FRONT 13mm 24.9531157 BODY, CLEAR DP8 1/8 GTP BODY 59.95 40633 SHOCK CAP, 13mm 18.9531159 BODY CLIPS, CHROME 4.95 40634 SHOCK SPRINGS ADJUSTER, 13mm 9.9531304 UP-RIGHT HUB REAR, PIVOT BALL 10.95 40636 O-RING 15x1mm 3.9531305 WASHER, PIVOT BALL, PLASTIC 5.95 40638 SHOCK PISTON 13mm 7.9531306 ALUM. HEX NUT, PIVOT BALL 4PCS 8.95 40640 SHOCK, PRESSURE TOP, ORANGE 5.9531307 PIVOT BALL, STEEL, REAR 4PCS 8.95 40642 ANTENNA , FIXING NUT 2.9531308 BARS, BALL & CUP SET 10.95 40643 PLASTIC SHOCK PARTS,13/16mmLX2 9.9534028 DOG BONE, 100mm 15.95 40711 4x90mm LOWER ARM SHAFT DM 7.9535247 SPUR, GEAR, 47T, 2SP REV2 7.95 40712 TURNBUCKLE,3.5x48mm,DM 9.9535248 SPUR, GEAR, 48T, 2SP REV2 7.95 40714 HANDLE BAR, CENTER DM 3.9535249 SPUR, GEAR, 49T, 2SP REV2 7.95 40716 UPPER ARM FRONT,DM 9.9535958 BEARING, 5X8mm 1 PC. 3.95 40717 LOWER ARMS FRONT & REAR DM 19.9536053 BEARING, 8x16mm, PAIR 12.95 40718 STEERING KNUCKLE,PIVOT BALL DM 19.9536055 PIN, 2.5x17mm, HEX HUBS, 4PCS 3.95 40719 ARM HOLDER PLASTIC DM 15.9536082 REAR AXLES, 8mm PAIR 10.95 40720 BUMPER,SIDE BODY DM 9.9536700 STEERING BALL END, 7mm, 8PCS. 6.95 40721 BUMPER FRONT & REAR DM 19.9536742 BUSHING, SERVO SAVER 1.95 40725 BUMPER FOAM DM 14.9536790 4x46MMTURNBUCKLES,4PCS. 10.95 40736 SHOCK SHAFT DM-1 7.9536850 7mm BALL, 6 PCS. 3.95 40737 SHOCK BODY, 13mm DM-1 24.9536861 5x40mm TURNBUCKLES, 2 PCS BLK 6.95 40738 SHOCK SPRING DM-1 RED SOFT 14.9536903 PIVOT BALLS, STEEL (mbx4) 4PCS 7.95 40745 UPPER FRONT PLATE BLACK 7.9536904 14mm ALUM. NUT (mbx4) 4 PCS 9.95 40746 SERVO CONNECTING PLATE BLACK 9.9537320 TURNBUCKLES, 3x26mm 2 PC 3.95 40750 SHOCK TOWER RR ALUM DM1 SPEC 14.9537410 BODY CLIPS, 10 PCS. SMALL JL10 3.95 40751 SPRINGS, RR RED SOFT DM1-SPEC 9.9537650 PLASTIC BALL END,4mm JL10 6.95 40759 SINGLE GEAR SHAFT DM-1E 12.9540009 DIFF O-RING SEALS, 2PCS 2.95 40760 CENTER GEAR MOUNT DM-1E 14.9540010 DIFF PINS,2.5X13.8MM,2PCS 2.95 40761 CHASSIS CNC 6061 DM-1E 99.9540011 DIFF GASKETS,3PCS 3.95 40762 CENTER DOGBONE DM-1E 90/97MM 19.9540024 OUTER DIFF SHIM,13X16XO.2MM 2.95 41202 CNC MOTOR MOUNT NEXX8 29.9540034 SERVO SAVER RING,ADJ. NUT,ALUM 5.95 86023 17mm WHEELS, V SPOKE, BLACK PK 19.9540037 STEERING PLATE HEX SCREWS 5.95 86024 17mm WHEELS, V SPOKE, BLUE PK 19.9540038 BALLS, 7MM 4PCS. 9.95 86025 17mm WHEELS, V SPOKE, LIME PK 19.9540040 CENTER DIFF MOUNT,NYLON 4.95 86026 17mm WHEELS, V SPOKE, WHITE PK 19.9540054 SHOCK SHAFTS,3.5m FR 13/16mm 7.95 86027 17mm WHEELS, V SPOKE,ORANGE PK 19.9540060 SHOCK PISTON LOCKNUT,2.5mm,4PC 4.95 86028 17mm WHEELS, V SPOKE, GRAY PAK 19.9540063 SHOCK SPRING CUP,4 PCS. 6.95 86029 17mm WHEELS, V SPOKE, YEL PACK 19.9540065 REAR UPPER ARM PLASTIC ROD END 4.95 86030 17mm WHEELS, V SPOKE,CHROME PK 23.9540090 SHOCK REBIULD KIT,13MM 7.95 86050 1:8 TIRE, SLICK w/o BELT, PAIR 19.9540117 TRUCK BODY MOUNT NEW 10.95 86051 1:8 TIRE, SLICK with BELT,PAIR 35.9540120 BRAKE CAP JOINT,8MM DM-1 11.95 86052 1:8 TIRE,TREADED w/o BELT, PR. 19.9540126 WASHER FLANGE 3x6x2.5 3.95 86053 1:8 TIRE,TREADED with BELT,PR. 35.9540500 SERVO SAVER SPRING, X1-CR 3.95 86059 FOAM STRIPS, INSERTS, LOW-PRO 9.9540563 SERVO SAVER TUBE 9.95

34328 DM-1e SPEC PARTS LIST

RACER’S NAME TEL:( )

ADDRESS

CITY STATE ZIP

DEALER’S NAME TEL: ( )

ADDRESS

CITY STATE ZIP

OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and han-dling this kit will provide many hours of enjoyment.

The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date.

In the event that the kit is incomplete or component parts are broken due to error in manufacturer, contact yourdealer from which you purchased the kit for replacement part or call OFNA at (949) 586-2910 for your nearest dealerlocation. Other items such as radio and engine other covered by individual warranties.

IMPORTANT!Please print or type, filling in the information listed below and mail immediately

MAIL TO:

OFNA RACING7 VANDERBILT

IRVINE, CA. 92618TEL: (949) 586-2910

OWNER’S REGISTRATION CARD

REGISTRATION CARDWrite in Your Model Name and Part Number

OFNA7 VanderbiltIrvine, Ca. 92618

Documents

DM-1e SPEC.pdf