玻璃纤维箱 EN 62208-2011 REPORT. (1)

Shenzhen BST Technology Co., Ltd. Report No. BST13050115Y-1SR-2

Building No.23-24, Zhiheng Industrial Park, Guankouer Road, Nantou,Nanshan District,Shenzhen,Guangdong,China

Tel: 400-882-9628 E-mail:[email protected] Complaints hotline:86-755-26747756 http://www.bst-lab.com Page 1 of 11

ZHEJIANG TIANQI ELECTRIC CO.,LTD.

LVD REPORT

Prepared For : ZHEJIANG TIANQI ELECTRIC CO.,LTD. Tianzi Lake Industrial zone, Gaoyu town, Anji county, Houzhou city, Zhejiang Province

Product Name: POLYESTER ENCLOSURE

Trade Name: TIBOX

Model : TIP-86, TIP-325, TIP-43, TIP-44, TIP-54, TIP-64, TIP-65, TX-43, TX-44, TX-54, TX-64, TX-65, TX-86

Prepared By : Shenzhen BST Technology Co., Ltd.


Test Date: May 09, 2013– May 14, 2013

Date of Report : May 14, 2013

Report No.: BST13050115Y-1SR-2




LVD Report EN 62208:2011

Empty enclosures for low-voltage switchgear and controlgear assemblies — General requirements

Testing laboratory ………………….. : Shenzhen BST Technology Co.,Ltd.

Address ……………………………….. : Building No.23-24, Zhiheng Industrial Park, Guankouer Road, Nantou,Nanshan District,Shenzhen,Guangdong,China

Testing location …………………….. : Shenzhen BST Technology Co.,Ltd.

Applicant ……………………………… : ZHEJIANG TIANQI ELECTRIC CO.,LTD.

Address ……………………………….. : Tianzi Lake Industrial zone, Gaoyu town, Anji county, Houzhou city, Zhejiang Province

Standard ………………………………. : EN 62208:2011

Test Result ……………………………. : Compliance with

EN 62208:2011

Procedure deviation ………………… : CE-LVD.

Non-standard test method ………… : N.A.

Type of test object ………………….. : POLYESTER ENCLOSURE

Trademark ……………………………. : TIBOX

Model/type reference ……………….. : TIP-86, TIP-325, TIP-43, TIP-44, TIP-54, TIP-64, TIP-65, TX-43, TX-44, TX-54, TX-64, TX-65, TX-86

Rating …………………………………. : N.A.

Manufacturer …………………………. : ZHEJIANG TIANQI ELECTRIC CO.,LTD.

Address ……………………………….. : Tianzi Lake Industrial zone, Gaoyu town, Anji county, Houzhou city, Zhejiang Province

Test item particulars :

Operation condition ………………… : N.A.




Possible test case verdicts :

test case does not apply to the test object …….. : N(.A.)

test object does meet the requirement …….…… : P(ass)

test object does not meet the requirement ……. : F(ail)

General remarks:

"(see remark #)" refers to a remark appended to the report.

"(see appended table)" refers to a table appended to the report.

Throughout this report a comma is used as the decimal separator.

The test results presented in this report relate only to the object tested.

This report shall not be reproduced except in full without the written approval of the testing laboratory.

Attached with:

A. photo documentation

Remark:




Artwork of Marking Label

Product: PLASTIC ENCLOSUREModel: TJ-AG

ZHEJIANG TIANQI ELECTRIC CO.,LTD.




EN 62208 Clause Requirement - Test Result - Remark Verdict

4 Classification P a) the type of material P b) method of fixing P c) the intended location P d) the degree of protection P e) rated insulation voltage N

5 EMC requirements N

6 Information to be given regarding the enclosure P 6.1 Marking ---

Name, trade mark or identification mark of the enclosure manufacturer

P

type designation or identification number of the enclosure

P

The marking shall be durable and easily legible and may be inside the enclosure

P

Marking for the recycling of plastic parts N

6.2 Documentation P

7 Service conditions P

7.1 Normal service conditions P

7.1.1.1 Ambient air temperature for indoor locations The ambient air temperature does not exceed +40 °C and its average over a period of 24 h does not exceed +35 °C. The lower limit of the ambient air temperature is –5 °C.

P

7.1.1.2 Ambient air temperature for outdoor locations N

7.1.2 Atmospheric conditions P

7.1.2.1 Atmospheric conditions for indoor locations The air is clean and its relative humidity does not exceed 50 % at a maximum temperature of +40 °C. Higher relative humidity may be permitted at lower temperatures, for example 90 % at +20 °C.

P

7.1.2.2 Atmospheric conditions for outdoor locations N

7.1.3 Description of locations P

For outdoor locations the additional tests N


EN 62208

Clause Requirement - Test Result - Remark Verdict



specified in 9.11 and 9.12 apply.

For indoor locations, the additional test specified in 9.12.1 a) applies.

P

7.2 Special service conditions N

Abnormal ambient air temperature and humidity N

Presence of corrosive substances N

Presence of particular dusts (coal, cement, etc.) N

Abnormal mechanical stresses (seismic, etc.) N

Presence of fauna, flora, mould N

Lonizing influences N

Electromagnetic interferences N

Vibrations N

Agreements reached shall not contradict any safety regulations in force.

N

7.3 Conditions during transport and storage Unless otherwise specified, the following temperature range applies during transport and storage: between –25 °C to +55 °C and for short periods not exceeding 24 h up to +70 °C.

P

8 Design and construction P

8.1 General P

8.2 Dimensions P

8.3 Mounting arrangements N

8.3.1 Enclosure P

8.3.2 Equipment mounting surfaces P

8.4 Static loads P

8.5 Lifting and transport support P

8.6 Access to the interior of the enclosure P

8.7 Protective circuit P

8.8 Dielectric strength P

8.9 Degree of protection (IK code) N

8.10 Degree of protection (IP code) P


EN 62208




9 Type tests P

9.1 General conditions of tests P

9.2 Marking 15 s with a piece of cloth soaked in water and then for 15 s with a piece of cloth soaked with petroleum spirit

P

9.3 Static loads P

9.4 Lifting P

9.5 Verification of axial loads of metal inserts N

9.6 Verification of degree of protection against external mechanical impacts (IK code)

N

9.7 Verification of degree of protection (IP code) P

9.7.1 Verification of degree of protection against access to hazardous parts and against the ingress of solid foreign objects indicated by first characteristic numeral

P

9.7.1.1 Verification of the protection against access to hazardous parts

P

9.7.1.2 Verification of degree of protection against the ingress of solid foreign objects

P

9.7.2 Verification of degree of protection against ingress of water as indicated by second characteristic numeral

P

9.7.3 Verification of degree of protection against hazardous parts as indicated by additional letter

P

9.8 Properties of insulating materials P

9.8.1 Verification of thermal stability P

9.8.2 Verification of resistance to heat P

9.8.3 Verification of resistance to abnormal heat and to fire

P

9.9 Verification of dielectric strength P

9.10 Verification of the continuity of the protective circuit

N

9.11 Verification of resistance to weathering P

9.12 Verification of resistance to corrosion N

9.12.1 Test procedure N

a) Enclosures or metallic parts intended to be N


EN 62208




installed indoors and internal parts of enclosures intended to be installed outdoors

b) Enclosures or metallic parts intended to be installed outdoors

N




ANNEX A:

Photo-documentation




Figure 1 General Appearance of the EUT







Documents

玻璃纤维箱 EN 62208-2011 REPORT. (1)