Upload
ena
View
34
Download
0
Tags:
Embed Size (px)
DESCRIPTION
Review of Chapter 4. Start the router simulator. You will see the prompt " Router> ". This is the user mode prompt. Change the name of the router to Router1. Set the enable password to “en123”. Set the secret password to “secret123”. Try the passwords. - PowerPoint PPT Presentation
Citation preview
IST 228\Ch5\IP Routing 1
IST 228\Ch5\IP Routing 2
Review of Chapter 4• Start the router simulator. You will see the prompt
"Router>". This is the user mode prompt.Change the name of the router to Router1.
• Set the enable password to “en123”.• Set the secret password to “secret123”.• Try the passwords.• Set virtual terminal password to “vty123” for the virtual
terminal 0-4Router1#config terminalRouter1(config)#line vty 0 4 Router1(config-line)#loginRouter1(config-line)#password vty123Router1(config-line)#exit
• Set console 0 password to “con123”Router1(config-line)#line console 0
• Now remove the passwords Router1(config)#no enable password en123
IST 228\Ch5\IP Routing 3
• Assign IP address for the Ethernet 0 interface.• Assign IP address for the Serial 0 interface.• Set the bandwidth of the Serial 0 interface to 56Kps.
Router1(config-if)#bandwidth 56• Set the bandwidth of the Serial 0 interface to 56Kps.
Router1(config-if)#clock rate 56000• Type “exit” to leave the serial interface and type “ctrl-z” to
leave configuration mode.• Show the configuration of Ethernet 0, Serial 0• Show the running configuration of Router1Backing up your configuration to a TFTP server
Router1#copy running-config tftp• Type “172.10.0.10” for the TFTP host.• Type “Router1” to name the destination file.
Router1#copy tftp running-config• Type “172.10.0.10” for the TFTP host.• Type “Router1” for the configuration file name.
IST 228\Ch5\IP Routing 4
IP Routing
• Nonroutable Protocols: – All communication occur on the one local net
segment– Network source and destination infromation is
not needed.– NetBEUI (NetBIOS Enhanced User Interface).
• Routed Protocols:– Have packet headers with Network Layer
address.– TCP/IP, Internetwork Packet Exchange/Squence
Packet Exchange.– Every device must configured with a unique IP or
IPX address.
IST 228\Ch5\IP Routing 5
IP Routing • Routers forward packets by looking the routing
table and discovering how to get remote networks.• A configured router have only information about
directly connected networks. – What happens a router receives a packet with a network
not listed in the routing table?
Routing table for RouterC
IST 228\Ch5\IP Routing 6
Different Types of Routing
• Static• Default• Dynamic
IST 228\Ch5\IP Routing 7
Static Routing•An administrator manually adds routes in each router’s table. •Benefits:
– No overhead on the router CPU– No bandwidth usage between routers– Security
•Disadvantages:– It is not feasible in large networks– Difficult to update– Administrators must know networking very well
ip route [destination_network] [mask] [next-hop_address or exit interface] [administrative_distance] [permanent]
IST 228\Ch5\IP Routing 8
Setting a Static Routing TableEstablishing routes:Router1# show ip route:Router1(config)# ip route 192.168.10.0 255.255.255.0
210.16.54.1This command establishes an IP route to network 192.168.20Add all other required routes in the routing tableType “crtl-Z” to exit from configuration mode. Check the status of the routing table using show ip route
Removing routes:Router1(config)# no ip route 192.168.10.0
255.255.255.0 210.16.54.1
Verifying:Router1# ping 192.168.10.50
IST 228\Ch5\IP Routing 9
Default Routing• Use to send packets with a remote
destination network not in the routing table to the next-hop router.
• You can only use default routing on stub networks-those with only one exit port out of the network.
RouterA(config)#ip route 0.0.0.0 0.0.0.0 192.168.12.1
IST 228\Ch5\IP Routing 10
Why use Default Routing?
IST 228\Ch5\IP Routing 11
Dynamic Routing• In dynamic routing, protocols are used to find and
update routing tables on routers.• A routing protocol defines the set of rules used by
a router when communicating between neighbor routers. – Routing Information Protocol (RIP)– Interior Gateway Routing Protocol (IGRP)– Enhanced Interior Gateway Routing Protocol (EIGRP)
• Types of routing protocols– interior gateway protocols (IGPs)
• RIP, IGRP, EIGRP, OSPF– exterior gateway protocols (EGPs)
• Border Gateway Protocol (BGP)
• Types of IGPs– Distance Vector (RIP, IGRP)– Link State (OSPF)– Hybrid (EIGRP)
IST 228\Ch5\IP Routing 12
Dynamic Routing Basics
• Hop count is the number of routers a packet must pass through to reach a particular network.
• An autonomous system (AS) is a group of routers under the control of a single administration, sharing the same routing table information.
• Administrative Distance is used to rate trustworthiness of routing information, 0 being the most trusted and the 255 least trusted.
IST 228\Ch5\IP Routing 13
Distance-Vector Routing Protocols• Each router broadcasts its entire routing
table to neighbor routers at predetermined intervals (30 to 90 seconds).
• Called routing by rumor
IST 228\Ch5\IP Routing 14
RIP Pinhole Congestion• Two updates list the same remote network?• Two updates list the same remote network and have the
same AD?• Two updates list the same remote network and have the
same AD and hop count?
IST 228\Ch5\IP Routing 15
Router Convergence
Start Up
Converged
IST 228\Ch5\IP Routing 16
Problems in Distance-Vector Routing• It takes up CPU process and link bandwidth.• If a network outage happens, slow converge
of distance-vector routing protocols can cause inconsistent routing tables.
• routing loops (counting-to-infinity).
IST 228\Ch5\IP Routing 17
Solutions
• Maximum Hop Count• Split Horizon• Route positioning• Holddowns
IST 228\Ch5\IP Routing 18
Routing Information Protocol (RIP)• a true distance-vector protocol• sends complete routing table out all
interfaces every 30 sec.• uses only hop count to determine the best
way.• has maximum allowable hop count of 15• is inefficient on large networks• uses three different timers
– route update timer– route invalid timer– flush timer
IST 228\Ch5\IP Routing 19
Setting up for Dynamic Routing• Configure your interfaces (see the next page)• Make sure that other routers in your network use
the same routing protocol (RIP or IGRP).Lab_A(config)# router rip
Lab_A(config-router)#network 201.100.11.0
^Z
• Check your settings with show ip route• Use ping to verify configuration and connectivity
of the network devices. • You can use passive-interface serial 0 to
stop RIP updates from being propagated out serial interface 0, but it can still receive RIP updates.
IST 228\Ch5\IP Routing 20
Example for RIP configuration
IST 228\Ch5\IP Routing 21
Interior Gateway Routing Protocol (IGRP)• Cisco-proprietary distance-vector routing
protocol that can work only with Cisco routers.
• maximum hop count of 255 (100 default)• can use bandwidth and delay of lines in
order to choose the best route.• Timers to control the performance
– update timers – invalid timers– holddown timers– flush
IST 228\Ch5\IP Routing 22
Commands to verify your configuration
Commands Meaning
show ip route shows you the routing protocols configured on your router and routing table
show protocols displays all routed protocols and the interfaces on which they are enabled.
show ip protocols shows the routing protocols with all timing associated with them
debug ip rip displays routing updates in the console session as they are sent and received.
debug ip igrp events displays a summary of the IGRP routing information running on the network
debug ip igrp transactions displays the message request from neighbor routers asking for updates.
undebug all turns all debugging off
show running-config shows the configuration currently running on the router
IST 228\Ch5\IP Routing 23
Commands for configuration routing
Commands Meaning
R(config)#router rip Turns on RIP routing on a router
R(config)#router igrp [AS number] Turns on IGRP routing on a router
R(config)#network [network IP] Identifies networks that routing table will be advertised by RIP and IGRP
R(config)#ip route [IP] [mask] [interface IP]
Creates static and default routes on a router
R(config)#ip route [IP] [mask] [interface IP]
Removes static and default routes
R(config)#ip classes Tells a router to forward packets to a default route when the destination network is not in the routing table
IST 228\Ch5\IP Routing 24
Commands to configure dynamic