- Tiger Trucktigertruck.com/wp-content/uploads/2015/12/M201_Wiring... · 2016-10-07 · Read Wiring Diagram and Analyze Causes Make a complete

M201 2014.01

Table of Contents

1.1.1 Introduction........................................................................................................... 1.1.1-1

1.1.2 Symbol................................................................................................................... 1.1.2-1

1.1.3 Circuit Fault Diagnosis ........................................................................................ 1.1.3-1Diagnostic Procedure ......................................................................................................... 1.1.3-1Diagnostic Tools.................................................................................................................. 1.1.3-1Fault Testing ....................................................................................................................... 1.1.3-2Repair Tools........................................................................................................................ 1.1.3-4Wiring Harness Terminal Repair ......................................................................................... 1.1.3-6

3.1.4 Cooling System .................................................................................................... 3.1.4-1

3.1.7 Fuel System .......................................................................................................... 3.1.7-1

3.1.8 Ignition System..................................................................................................... 3.1.8-1

3.1.9 Starting System .................................................................................................... 3.1.9-1

3.1.10 Charging System ................................................................................................ 3.1.10-1

3.1.12 Electronic Control System................................................................................. 3.1.12-1Power Supply and Data Line .............................................................................................. 3.1.12-2HO2S/EVAP........................................................................................................................ 3.1.12-3TPS/KS/IAC ........................................................................................................................ 3.1.12-5CKP/Evaporator Thermistor/ECT/IAT ................................................................................. 3.1.12-7

4.1.1 Heating, Ventilation and Air Conditioning.......................................................... 4.1.1-1Compressor and Sensor Control Operation ....................................................................... 4.1.1-2Power Supply/Sensor/Actuator........................................................................................... 4.1.1-4

4.2.2 Instrument Cluster................................................................................................ 4.2.2-1Power Supply and Signal.................................................................................................... 4.2.2-2Signal Lamp........................................................................................................................ 4.2.2-4Lighting Signal Lamp .......................................................................................................... 4.2.2-6

4.2.3 Horn ....................................................................................................................... 4.2.3-1

4.2.4 Cigarette Lighter................................................................................................... 4.2.4-1

4.2.5 Information and Entertainment System.............................................................. 4.2.5-1Power Supply...................................................................................................................... 4.2.5-2Speaker............................................................................................................................... 4.2.5-3

M201 2014.01

Table of Contents

4.2.6 Lighting System ....................................................................................................4.2.6-1Headlamp............................................................................................................................ 4.2.6-2Brake Lamp......................................................................................................................... 4.2.6-5Turn Lamp........................................................................................................................... 4.2.6-7Position Lamp and License Plate Lamp.............................................................................. 4.2.6-11Fog Lamp............................................................................................................................ 4.2.6-13Backup Lamp ...................................................................................................................... 4.2.6-15Interior Lamp....................................................................................................................... 4.2.6-17

4.2.7 Wiper ......................................................................................................................4.2.7-1Front Wiper ......................................................................................................................... 4.2.7-1

4.2.8 Central Door Lock .................................................................................................4.2.8-1

4.2.9 Power Window.......................................................................................................4.2.9-1

4.2.10 Body Control System..........................................................................................4.2.10-1

4.2.11 On-board Network System .................................................................................4.2.11-1DLC (Data Link Connector)................................................................................................. 4.2.11-1

6.1.1 Fuses and Relays..................................................................................................6.1.1-1Main Fuse Box .................................................................................................................... 6.1.1-1I/P Fuse Box ....................................................................................................................... 6.1.1-2

6.1.2 Power Supply Distribution ...................................................................................6.1.2-1I/P Power Supply Distribution 1........................................................................................... 6.1.2-1I/P Power Supply Distribution 2........................................................................................... 6.1.2-2I/P Power Supply Distribution 3........................................................................................... 6.1.2-3

6.1.3 Fuse Details ...........................................................................................................6.1.3-1

6.1.4 Grounding Distribution.........................................................................................6.1.4-1

6.1.5 Wiring Harness Connector Location View..........................................................6.1.5-1

6.1.6 Grounding Location View.....................................................................................6.1.6-1

6.1.7 Wiring Harness Connector Terminal View..........................................................6.1.7-1

6.1.8 Abbreviation ..........................................................................................................6.1.8-1

M201 2014.01

1.1.1-1 1.1.1-1Introduction

M1101001

I/P Fuse Box P40

2

7

1

Main Fuse Box P01

Fuel System

1.25

BU

/WH

1.25

BU

/WH

3 X07

0.5

WH

/BN

0.5

WH

/YE

0.5

WH

/GN

0.5

WH

/BK

1.0

RD

/BU

1.0

RD

/BU

1.0

RD

/BU

1.0

RD

/BU1.25

RD

/BU

1.25

RD

/BU

2 E09

1 E09

2 E06

1 E06

2 E04

1 E04

2 E02

1 E02

8.0

WH

8.0

WH

8.0

WH

2

IF15

15A

29

30

1

EF01

80A

67

65

68

69

IR05

ECM

0.5

BN/W

H0.

5 BN

/WH

32 E18

15 X05

0.5

YE/R

D0.

5 YE

/RD

60 E18

25 X05

1.25

BU

/WH

16 X04

IF19

15A

37

38

82

80

83

84

IR08

2.0

RD

/BU

2.0

BK1.

25 B

K1.

25 B

K

G201

4

2

S01

S01

FuelPump

Fuel Injector 1

Fuel Injector 2

Fuel Injector 3

Fuel Injector 4

2.0

RD

/BU

M

50 E18 63 E18 49 E18 64 E18

Refer to 3.1.12 Electronic Control

System

1 X05

4 X07

13

10

3

4

9+B

12

11

6

5

8

1.1.1 Introduction

1.1.1-2

M201 2014.01

1.1.1-2Introduction

1. System name.

2. Wiring harness connector numbering.

In this manual, the wiring harness connectoris numbered based on wiring harness. Forexample, connector of ECM wiring harness inengine wiring harnesses is numbered as E01.E is the wiring harness code, 01 is theconnector serial number.

The following table lists are wiring harness codes:

Note： Door wiring harness consists of wiring harness of two front doors andback door.

Note：For wiring harness connector numbering details, please refer to wiring harness layout views.

3. Component name.

4. System information related to the circuit.

5. Wiring harness to wiring harness connector,the black arrow represents positive pole andthe box represents the negative pole. Thecharacter in the box is the connector code.

6. Wiring harness color and width. The followingtable shows the color code.

If a wiring harness has two colors, the firstcharacter shows the background color and thesecond shows the stripe color, divided by “/”.

For example, YE/WH means yellow backgroundcolor with white stripe.

7. Pin number. The pin number of matedconnector pair are mirrored relationship, asshown below:

8. Grounding number. The grounding numberstarts with G. For grounding details, pleaserefer to grounding layout views.

Code Wiring Harness NameEN Engine wiring harness

E-- Engine wiring harness connector

I/P I/P wiring harness

P-- I/P wiring harness connector

SO Chassis wiring harness

S-- Chassis wiring harness connector

DR Door wiring harness

D-- Door wiring harness connector

RF Roof Wiring Harness

L-- Roof Wiring Harness connector

X-- Wiring harness to wiring harness connector

Color Code Wiring Harness Color Legend

BK Black

BN Brown

BU Blue

GN Green

GY Grey

LG Light Green

LU Light Blue

OG Orange

PK Pink

RD Red

SR Silver

VT Purple

WH White

YE Yellow

1 2 34 5 6

123456

M1101002

M201 2014.01

1.1.1-3 1.1.1-3Introduction

9. Power supply type supplied to fuse. +Brepresents battery power supply. ACCrepresents power supply when ignition switchis at “ACC”. IG1 represents terminal 2 outputwhen ignition switch is at “ON”. IG2represents terminal 5 output when ignitionswitch is at “ON”.

Note： The difference between IG1 andIG2 is that there is power supply output from IG1, but no from IG2 when the ignition switch is at “ST”.

10. Wiring harness splice point

11. Fuse number consists of a fuse code and asequential number. Code EF representsfuses in the main fuse and relay box; Code IFrepresents fuses in instrument panel fuse andrelay box. For details, please refer to fusetable.

12. A relay is represented by two capital Englishletters. Code ER represents relays in themain fuse and relay box; Code IR representsrelays in the instrument panel fuse and relaybox. For details, please refer to the relaytable.

13. Filling grey shade means the electroniccomponent, P01 represents the wiringharness connector code.

14. Circuit differences in different models,engines or specifications are noted bydashed lines and texts beside the circuit.

15. The 8-shaped symbol between wiringharnesses represents ‘Unshielded TwistedPair’ (UTP), which is used for sensor signal ordata communication.

16. If a system wiring diagram requires more than onepage, it starts with and ends with . If more thanone circuit extends to the next page, use B, C and otherletters to represent respectively.

Not Spliced Cross Circuit

Spliced Cross Circuit

M1101003

0.5 BK/WH

0.85

BK/

WH

ECM(1.0L)

ECM(1.3L)

17S0

113

S01a

M1101004

0.5 BU

0.5 VT

M1101005

A1 A1

0.5 RD/YEA1

0.5 RD/YE A1

M1101006

M201 2014.01

1.1.2-1 1.1.2-1Symbol

Grounding

TemperatureSensor

Solenoid

Solenoid

Light LoadFuse

Moderate LoadFuse

Heavy LoadFuse

Heater

Normal CloseRelay

Normal OpenRelay

Double ThrowRelay

Resistor

Potentiometer

Rheostat

Ignition Coil

Battery

Capacitor

Cigarette Lighter

Antenna

Normal OpenSwitch

Normal CloseSwitch

Double ThrowSwitch

Knock Sensor

G7

M1102001

1.1.2 Symbol

1.1.2-2

M201 2014.01

1.1.2-2Symbol

UTP(UnshieldedTwisted Pair)

Starting Motor

Oxygen Sensor

Stopper Switch

Diode

Photodiode

Light EmittingDiode

Motor

Not Spliced Cross Circuit

Bulb

Horn

Clock Spring

Airbag

Spliced Cross Circuit

M

M

M

M1102002

M201 2014.01

1.1.3-1 1.1.3-1Circuit Fault Diagnosis

Diagnostic ProcedureRefer to the following procedure for the circuitfault diagnosis:

1. Confirm Fault

To do the proper repair, confirm the faultsymptoms described by the customer firstly.Inspect the relevant component carefully toconfirm the fault symptoms and make record.DO NOT disassemble the component beforeconfirmation of the fault scope and causes.

2. Read Wiring Diagram and Analyze Causes

Make a complete analysis and judgement onthe fault components from power supply togrounding according to the sub-system wiringdiagram and determine the repair solution. Ifit cannot be determined, please read thesystem description in the “Description andOperation” section in the repair manual tounderstand the working principle. And inspectother circuits that has common part with thefault circuit, for example, the fuse, grounding,switch, etc. Inspect the circuit not covered instep 1. If other components in the commoncircuit work properly, it means the fault existsin its own circuit. Otherwise, the fuse orgrounding may have faults.

3. Inspect Circuits and Components

Always use the wiring diagram together withrepair manual and refer to the diagnosticprocedure for the relevant circuits orcomponents in the repair manual. For thecircuit with a control module, fully usediagnostic tools to do the test. Effectivediagnosis should be a logical and reasonableoperation. Fully use the diagnosticprocedures in the repair manual and start theinspection from the causes with mostpossibility and the components with easiestinspection way.

4. Repair Fault

Repair the fault. Refer to the wiring diagramand the description for fault treatment inrepair manual. For example, the diagnosticprocedure for poor grounding and the wiringharness connector treatment.

5. Confirm Circuit Working Condition

After repair, all functions should be reinspectedto confirm the fault repaired. For the fuse blownfault, Inspect all the relevant circuits using thisfuse.

Diagnostic Tools1. Voltmeter and Test Lamp

Use test lamp or voltmeter to inspect thecircuit status. Test lamp comprises a pair ofwiring harnesses and a 12 V bulb. Wheninspecting, connect one wiring harness to theground and the other one to the certainmeasurement point. If the bulb is lit, it meansthe measurement point has power supply.

Warning: DO NOT use test lamp to inspectthe control module voltage. Otherwise itcould damage the interior circuit insidethe control module. Please use a voltmeterwith 10 MΩ or higher internal resistance(for example, to test the ECM voltage).

Voltmeter has the same connection methodas the test lamp, but voltmeter can display thevoltage value of the circuit. Use a voltmeterwith high resistance to test the voltage. If thecircuit has poor connection, the voltmetermay show the normal value, but the voltagecannot drive the load successfully.

M1103001

1.1.3 Circuit Fault Diagnosis

1.1.3-2

M201 2014.01

1.1.3-2Circuit Fault Diagnosis

2. Self-powered Test Lamp and Ohmmeter

Use test lamp with own 12 V power supply orohmmeter to inspect the circuit for continuity.Test lamp comprises a bulb, battery and a pairof wiring harnesses. The bulb will be lit whenthe two wiring harnesses are connected.Before testing, disconnect the negativebattery cable and pull out the fuse of thecircuit. To test the circuit for continuity,connect two wiring harnesses to the twomeasurement points. If the bulb is lit, it meansthe circuit is normal.

Warning: DO NOT use self-powered testlamp to inspect the control module.Otherwise, it could damage the interiorcircuit inside the control module. Pleaseuse a ohmmeter with 10 MΩ or higherinternal resistance.

Ohmmeter has the same usage method asvoltmeter, but ohmmeter can show theresistance value. The lower resistance, thebetter continuity.

3. Jumper Wire with Fuse

Use jumper wire to test a broken point foropen loop circuit (circuit open). The jumperwire is a tool that should be in tandem withthe circuit.

Warning: To protect the circuit to beinspected, DO NOT use the fuse higherthan the rated capacity of circuit toinspect relevant circuits. DO NOT use thejumper wire as the input or output signalwhen a control module such as ECM orTCM is in the circuit. Otherwise it coulddamage the circuit interior inside thecontrol module.

Fault Testing1. Voltage Testing

Voltage testing is to test the voltage at acertain point. When testing a certainconnector terminal, insert the positive probeinto the wiring harness from the connectorback without assembling wiring harnessconnector.

M1103002

5A

M1103003

Test Lamp

Solenoid

Switch

5A+B

0.5R

DI/P Fuse andRelay Box

Voltmeter0.

5G

2 E00

1 E00

1 C00

M1103004

M201 2014.01


1 When testing the voltage with test lampor voltmeter, connect the negative oftesting tools to battery negative.

2 Connect the other wiring harness of thetest lamp or the positive probe of thevoltmeter to the test position.

3 If a voltmeter is used and voltage displaylower 1 V above compared to the ratedvalue, it means a circuit fault. It means acircuit fault if a test lamp is used and lampis not lit.

2. Power Testing

1 Disconnect the negative battery cable.

2 Connect one wiring harness of the self-powered test lamp or the probe of theohmmeter to the test component. If usingohmmeter, please connect the twoprobes each other and use reset buttonto adjust the ohmmeter to zero.

3 Connect the other wiring harness of thetest lamp or probe of the ohmmeter to theother side of the test load.

4 If the bulb is lit, it means the circuit isnormal. If an ohmmeter is used and theresistance value is very low or close to 0Ω, it means the component has goodcontinuity.

3. Short Circuit Testing

1 Disconnect negative battery cable.

2 Connect one wiring harness of the self-powered test lamp or one probe of theohmmeter to the output terminal of thefuse.

3 Connect the other wiring harness of thetest lamp or other probe of the ohmmeterto the grounding.

4 Disconnect all the electrical loads to thefuse.

CAUTION: If not disconnecting all the electrical loads to the fuse, when testing the low resistance circuit like lights, the ohmmeter will always display the low value. This will cause wrong judgement.

5 Do the careful inspection from the placeclosest to the fuse.

6 If the bulb is lit or ohmmeter has valuedisplay less than 5 Ω, it means the shortcircuit to the ground.

Switch

M1103005

Test Lamp

Solenoid

Switch

I/P Fuse andRelay Box

Voltmeter

5A

+B

0.5R

D0.

5G

2 E00

1 E00

1 C00

M1103006

1.1.3-4

M201 2014.01


4. Voltage Drop Testing

This is a test to inspect the voltage drop alongthe wiring harness, connector or switch.

1 Connect the positive probe of thevoltmeter to one end of the circuit close tothe battery (connector or switch side).

2 Connect the negative probe to the otherend of the circuit (the other side ofconnector or switch).

3 Switch on or off to make the circuit work.

4 The voltmeter will display the voltagedifference between the two test points.

5 If the voltage difference is more than 0.1V (less than 50 mV for 5 V voltagecircuit), it means a circuit fault. Inspect forloose, oxidized or corrosive circuit.

Repair Tools

1. 5 KΩ Rheostat

It can simulate each ohm-type sensor signal,like coolant temperature sensor, air intaketemperature sensor and the like. And helpmake quick judgement on the performance ofthe component.

Switch

Solenoid

Voltmeter

5A

+B

0.5R

D

I/P Fuse andRelay Box

0.5G

2 E00

1 E00

1 C00

M1103007

M1103008

M1103009

M201 2014.01


2. LED Test Lamp

Bidirectional two-color LED lamp can changeits color when exchanging the positive andnegative. This feature can be used to test thePWM control signals of Hall sensor.

3. Airbag Test Tool

Before installing a new airbag after airbagsystem has faults or vehicle accident, installthis tool to the airbag system, and usediagnostic tools to confirm the airbag systemwork properly. After that, install the newairbag. This process can guarantee a safeairbag operation.

4. Probe

When testing a system component, insert thistool into the connector from the back and it isunnecessary to break the wiring harness toreduce man-made fault.

5. Terminal Repair Tool

When maintaining and repairing certainterminal, use this tool to separate them fromthe connector.

M1103010

M1103011

M1103012

M1103013

1.1.3-6

M201 2014.01


Wiring Harness Terminal Repair1. Remove the terminal pin.

2. Separate the clip with wiring harness terminalrepair tool.

3. Pull out the wiring harness terminal from therear of connector.

M1103014

Wiring HarnessTerminal Clip

Wiring Harness TerminalRepair Tool

M1103015

M1103016

M201 2014.01


4. Adjust and clean the wiring harness terminalcontact plate pulled out from connector.

M1103017

1.1.3-8

M201 2014.01


Poor Grounding Connection Repair Procedure1. Remove the grounding bolt.

2. Clean the two surfaces (both bolt side andvehicle contact side) of the copper ring withabrasive cloth until the oxide completelycleared.

3. Clean the grounding surface on the vehiclewith abrasive cloth until it is completelycleaned.

M1103018

M1103019

M1103020

M201 2014.01


4. Reinstall the wiring harness and retaining boltof grounding. Tighten to specified torque.

Torque for M6 bolt: 8 Nm

Torque for M8 bolt: 20 Nm

M1103021

3.1.4-1

M201 2014.01

3.1.4-1Cooling System

Cooling System

I/P Fuse Box P40Main Fuse Box P018.

0 W

H8.

0 W

H

8.0

WH

+B

2IF

15

15A

29

301

EF01

80A

67

65

68

69

IR05

ECM

0.5

BN/W

H0.

5 BN

/WH

32 E18

15 X05

2.0

RD

/BU

2.0

BK2.

0 BK

G103

0.5

BK/R

D0.

5 BK

/RD

2.0

RD

/BK

60 64

23 X05

62

1

2

P13

P13

2.0

BU/W

H

0.5

RD

/BU

IF04

20A

7

8

IR04

62 63

CondenserFan

RadiatorFan

2.0

BK2.

0 BK

G105

0.5

BK/W

H

2.0

BU/R

D

0.5

BK/W

H

2.0

RD

/BU

0.5

RD

/BU

IF03

30A

5

6

IR03

5857

55 59

19 X05 1

2

P10

P10

M M

52 E18 E18

M3104001

3.1.4 Cooling System

M201 2014.01

3.1.4-2 3.1.4-2Cooling System

• Operating circuit analysis of radiator fan is as follows:

Current from the battery positive → Main fuse box (main fuse EF01) → I/P fuse box (radiator fan fuseIF03) → Radiator fan relay-terminal 58 → Radiator fan relay closing contact → Radiator fan relay-terminal 59→Radiator fan connector P10-terminal 1→Radiator fan motor→Radiator fan connectorP10-terminal 2 → Grounding G105

Radiator fan motor is powered on and fan starts to work normally.

• Operating circuit analysis of condenser fan is as follows:

Current from the battery positive → Main fuse box (main fuse EF01) → I/P fuse box (radiator fan fuseIF04) → Condenser fan relay-terminal 63 → Condenser fan relay closing contact → Condenser fanrelay-terminal 64 → Condenser connector P13-terminal 1 → Condenser fan motor → Condenser fanconnector P13-terminal 2 → Grounding G103

Condenser fan motor is powered on and fan starts to work normally.

3.1.4-3

M201 2014.01

3.1.4-3Cooling System

Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24

IR01 IR02 IR03 IR04 IR05

IF40 IF39 IF38 IF37 IF36 IF35 IF34 IF33 IF32 IF31 IF30 IF29 IF28 IF27 IF26 IF25

IF23 IF22 IF21 IF20 IF19 IF18 IF17 IF16 IF15 IF14 IF13 IF12 IF11 IF10 IF09

IF08 IF02 IF03 IF04 IF05 IF06


P40

M201 2014.01

3.1.4-4 3.1.4-4Cooling System

I/P Wiring Harness to Engine Wiring Harness Engine Wiring Harness to I/P Wiring Harness

Radiator Fan Condenser Fan

ECM

1 7 8 9 10 411 12 13 14

2 15 16 17 18 5

19 20 21 223 23 24 25 26 6

1

2

3

7

11

15

19

23

8

12

16

20

24

9

13

17

21

25

10

14

18

22

26

4

5

6

X05

12

P10

12

P13

7 8

5 6

3 4

1 2

51 52 53 54 55 56 57 58 59 60 61 62 63 64

37 38 39 40 41 42 43 44 45 46 47 48 49 50

23 24 25 26 27 28 29 30 31 32 33 34 35 36

9 10 11 12 13 14 15 16 17 18 19 20 21 22

E18

3.1.7-1

M201 2014.01

3.1.7-1Fuel System

Fuel System

Fuel Injector 1

Fuel Injector 2

Fuel Injector 3

Fuel Injector 4

Main Fuse Box P01

1.25

BU

/WH

1.25

BU

/WH

3 X07

0.5

WH

/BN

0.5

WH

/YE

0.5

WH

/GN

0.5

WH

/BK

1.0

RD

/BU

1.0

RD

/BU

1.0

RD

/BU

1.0

RD

/BU1.25

RD

/BU

1.25

RD

/BU

2 E09

1 E09

2 E06

1 E06

2 E04

1 E04

2 E02

1 E02

I/P Fuse Box P40

8.0

WH

8.0

WH

8.0

WH

+B

2

IF15

15A

29

30

1

EF01

80A

67

65

68

69

IR05

ECM

0.5

BN/W

H0.

5 BN

/WH

32 E18

15 X050.

5 YE

/RD

0.5

YE/R

D

60 E18

25 X05

1.25

BU

/WH

16 X04

IF19

15A

37

38

82

80

83

84

IR08

2.0

RD

/BU

2.0

BK1.

25 B

K1.

25 B

K

G201

4

2

S01

S01

2.0

RD

/BU

M

50 E18 63 E18 49 E18 64 E18

Refer to 3.1.12Electronic Control

System

1 X05

4 X07

FuelPump

M3107001

3.1.7 Fuel System

M201 2014.01

3.1.7-2 3.1.7-2Fuel System

• Operating circuit analysis of fuel injector 1 is as follows:

Current from the battery positive → Main fuse box (main fuse EF01) → I/P fuse box (main relay fuseIF15) → Main relay-terminal 68 → Main relay closing contact → Main relay-terminal 69 → ConnectorX05-terminal 1 → Fuel injector 1 connector E09-terminal 1 → Fuel injector 1 coil → Fuel injector 1connector E09-terminal 2 → ECM connector E18-terminal 50 → ECM → Grounding

Fuel injector coil is powered on to inject oil and ECM controls fuel-injection amount through pulsewidth of power supply to fuel injector coil.





Current from the battery positive → Main fuse box (main fuse EF01) → I/P fuse box (main relay fuseIF15) → Main relay-terminal 68 → Main relay closing contact → Main relay-terminal 69 → ConnectorX05-terminal 1 → Fuel injector 3 connector E04-terminal 1 → Fuel injector 3 coil → Fuel injector 3connector E04 terminal 2 → ECM connector E18-terminal 49 → ECM → Grounding





• Operating circuit analysis of fuel pump is as follows:

Current from the battery positive → Main fuse box (main fuse EF01) → I/P fuse box (fuel pump fuseIF19) → Fuel pump relay-terminal 83 → Fuel pump closing contact → Fuel pump-terminal 84 →

Connector X04-terminal 16 → Connector X07-terminal 3 → Fuel pump connector S01-terminal 4 →

Fuel pump motor → Fuel pump connector S01-terminal 2 → Connector X07-terminal 4 → GroundingG201

Fuel pump motor is powered on to start work and ECM controls fuel pump running through fuelpump relay.

3.1.7-3

M201 2014.01

3.1.7-3Fuel System

Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

M201 2014.01

3.1.7-4 3.1.7-4Fuel System

I/P Wiring Harness to Chassis Wiring Harness Chassis Wiring Harness to I/P Wiring Harness


1 2 3 4 5 67 8 9 10

11 12 13 14 15 16

17 18 19 2021 22 23 24 25 26

12345678910

11121314151617181920

212223242526

X04

1 7 8 9 10 411 12 13 14

2 15 16 17 18 5

19 20 21 223 23 24 25 26 6

1

2

3

7

11

15

19

23

8

12

16

20

24

9

13

17

21

25

10

14

18

22

26

4

5

6

X05

3.1.7-5

M201 2014.01

3.1.7-5Fuel System

Chassis Wiring Harness to Fuel Pump Wiring Harness Fuel Pump Wiring Harness to Chassis Wiring Harness

Fuel Injector 1 Fuel Injector 2

Fuel Injector 3 Fuel Injector 4

13

24

1

2

3

4

X07

1 2

E09

1 2

E06

1 2

E04

1 2

E02

M201 2014.01

3.1.7-6 3.1.7-6Fuel System

ECM

Fuel Pump

7 8

5 6

3 4

1 2

51 52 53 54 55 56 57 58 59 60 61 62 63 64

37 38 39 40 41 42 43 44 45 46 47 48 49 50

23 24 25 26 27 28 29 30 31 32 33 34 35 36

9 10 11 12 13 14 15 16 17 18 19 20 21 22

E18

1

2

3

4

S01

3.1.8-1

M201 2014.01

3.1.8-1Ignition System

Ignition System

Main Fuse Box P010.

5 BU

/WH

0.5

BU/R

D0.

5 BU

/RD

I/P Fuse Box P40

Ignition Coil 1

Ignition Coil 2

Ignition Coil 3

Ignition Coil 4

Speed Sensor

8.0

WH

8.0

WH

8.0

WH

8.0

WH

+B

2 IF15

15A

29

30

1

EF01

80A

67

65

68

69

IR05

ECM

0.5

BN/W

H0.

5 BN

/WH

0.5

YE/B

K0.

5 YE

/BK

1.5

BK/Y

E

32 E18 3 E1819 E18

3 E083 E17 2 E17 1 E17 2 E08

15 X05

2.0

RD

/BU

2.0

RD

/BU

2.0

RD

/BU

1.5

RD

/BU

1 X05

1 E08

1.5

BK1.

0 BK

47 E1840 E18

G303

1.5

BK/V

T

6 E18

3 E07 2 E07

1.5

RD

/BU

1 E07

1.5

BK1.

0 BK

G303

1.5

BK/B

U

7 E18

3 E05 2 E05

1.5

RD

/BU

1 E05

1.5

BK1.

0 BK

G303

1.5

BK/R

D

1 E18

3 E03 2 E03

1.5

RD

/BU

1 E03

1.5

BK1.

0 BK

G303

M3108001

3.1.8 Ignition System

M201 2014.01

3.1.8-2 3.1.8-2Ignition System

• Operating circuit analysis of ignition coil 1 is as follows:

Ignition coil 1 is controlled by ECM through Connector E18-terminal 3 → Ignition coil 1 connectorE08-terminal 3→ Ignition coil. Current from the battery positive→Main fuse box (main fuse EF01)→I/P fuse box (main relay fuse IF15) → Main relay-terminal 68 → Main relay closing contact → Mainrelay-terminal 69 → Connector X05-terminal 1 → Ignition coil 1 connector E08-terminal 1 → Ignitioncoil → Ignition coil 1 connector E08-terminal 2 → Grounding G303

Ignition time of ignition coil is controlled by ECM according to the engine operating condition.










3.1.8-3

M201 2014.01


Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

M201 2014.01

3.1.8-4 3.1.8-4Ignition System


Ignition Coil 1 Ignition Coil 2

Ignition Coil 3 Ignition Coil 4

1 7 8 9 10 411 12 13 14

2 15 16 17 18 5

19 20 21 223 23 24 25 26 6

1

2

3

7

11

15

19

23

8

12

16

20

24

9

13

17

21

25

10

14

18

22

26

4

5

6

X05

1 2 3

E08

1 2 3

E07

1 2 3

E05

1 2 3

E03

3.1.8-5

M201 2014.01


Crankshaft Position Sensor

ECM

1 2 3

E17

7 8

5 6

3 4

1 2

51 52 53 54 55 56 57 58 59 60 61 62 63 64

37 38 39 40 41 42 43 44 45 46 47 48 49 50

23 24 25 26 27 28 29 30 31 32 33 34 35 36

9 10 11 12 13 14 15 16 17 18 19 20 21 22

E18

3.1.9-1

M201 2014.01

3.1.9-1Starting System

Starting System

Main Fuse Box P01

1 S161 S17

15.0 RD

1 S20

M

2.0

BK/Y

E2.

0 BK

/YE

1 S19

1

4 P31

6 P31

IG1

IG2ST ST

ACC

ACC

LOC

K

LOC

K OFF

OFF

L1 L2

Ignition Switch

Battery Starting Motor

8.0

WH

8.0

WH

8.0

WH

3.0

WH

/GN

1

2

EF01

80A

X04

2

1

IF0240A

I/P Fuse Box P40

M3109001

3.1.9 Starting System

M201 2014.01

3.1.9-2 3.1.9-2Starting System

• Operating circuit analysis of starting motor is is as follows:

Current from the battery positive → Main fuse box (main fuse EF01) → I/P fuse box (ignition switch 2fuse IF02) → Ignition switch connector P31-terminal 4 → Ignition switch ST contact → Ignition switchconnector P31-terminal 6 → Connector X04-terminal 1 → Starting motor connector S16-terminal 1 →

Starting motor solenoid switch → Starting motor grounding

• Starting motor solenoid switch is powered on to close two contacts of solenoid switch.

Current from the battery positive → Connector S17-terminal 1 → Solenoid switch closing contact →Starting motor coil → Starting motor grounding

Controlled by starting switch, starting motor starts to work.

3.1.9-3

M201 2014.01


Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

M201 2014.01

3.1.9-4 3.1.9-4Starting System


Ignition Switch Starting motor Switch

Starting motor Battery Positive

1 2 3 4 5 67 8 9 10

11 12 13 14 15 16

17 18 19 2021 22 23 24 25 26

12345678910

11121314151617181920

212223242526

X04

123

456

P31

1

S16

1

S17

1

S19

3.1.9-5

M201 2014.01


Battery Negative

S20

3.1.10-1

M201 2014.01

3.1.10-1Charging System

Charging System

Main Fuse Box P01

IF36

15A

72

71

IF33

10A

IG1

66

65

3.0

YE/B

K

I/P Fuse Box P40

Battery Alternator

Instrument Cluster

1 S20

1 S19

24 P21

0.3

WH

/RD

2 P031 P04 3 P03

8.0

WH

8.0

WH

1.25

BK/

BU

1

2

EF01

80A

M3110001

3.1.10 Charging System

M201 2014.01

3.1.10-2 3.1.10-2Charging System

• Operating circuit analysis of alternator is as follows:

When alternator is not working: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (ignition switch 1 fuse IF01) → Ignition switch connector P31-terminal 3 → Ignition switchIG1 contact → Ignition switch connector P31-terminal 2 → I/P fuse box (alternator fuse IF36) →

Alternator connector P03-terminal 2 → Alternator regulator and rotor coil → Alternator grounding

Current from instrument cluster (charging indicator) → Instrument cluster connector P21-terminal 24→ Alternator connector P03-terminal 3 → Alternator regulator → Alternator grounding

Charging indicator is turned on.

When the alternator is working: Current from alternator stator coil → Alternator commutator →

Connector P04-terminal 1 → Main fuse box (main fuse EF01) → Connector S19-terminal 1 → Battery

When the alternator is working, alternator regulator and rotor coil supply power to all electricaldevices in vehicle on one hand and charge battery on the other hand.

3.1.10-3

M201 2014.01

3.1.10-3Charging System

Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

M201 2014.01

3.1.10-4 3.1.10-4Charging System

Alternator Connector Alternator Positive

Instrument Cluster

Battery Positive Battery Negative

123

P03

1

P04

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

26 27 28 29 30 31 3217 18 19 20 21 22 23 24 25

P21

1

S19 S20

3.1.12-1

M201 2014.01

3.1.12-1Electronic Control System

Electronic Control System

M3112005

Carbon Canister Solenoid

16

32

851

371 2

24

13

B+IF11

IF15

IR05

IF30

17

12

10

44

18

26

4

2

1

2

3

3

IG1IF37

ECM

39

452

Front Oxygen Sensor

43

21

294

Rear Oxygen Sensor

DiodeTerminal 1

Diode A Terminal 1

Diode B Terminal 1

TristatePressure

Switch

1

2

3

4

22

21

35

36

Stepper Motor

12

13

5

28

9

56

57

20

24

DLC Terminal 15

15

Instrument Cluster

4

3

2

1

1

2

59

19

25

40

41

13

47

AirIntakePressure/TemperatureSensor

Coolant Temperature Sensor

1

2

2

1

3

Evaporator Thermistor


ThrottlePositionSensor

30

31

1

2KnockSensor

G301

5

G30143

48

G302

3.1.12 Electronic Control System

M201 2014.01

3.1.12-2 3.1.12-2Electronic Control System

Power Supply and Data Line

2.0

BK

5 E18

0.5

BK

/YE

61 E18

G301

0.5

BK

43 E18

G302

0.5

BK

48 E18

IF37

10A

74

73

IF33

10A

IG1

66

65

3.0

YE/B

K

I/P Fuse Box P40

Main Fuse Box P01

IF11

10A

8.0

WH

8.0

WH

8.0

WH

8.0

WH

8.0

WH

0.5

PK/B

U

0.5 PK/BU

0.5

PK/B

U0.

5 PK

/BU

+B

2

21

22

IF15

15A

29

30

1

EF01

80A

0.5

BU

/BK

10 E18

0.5

PK

/BK

44 E18

0.5

LG/R

D

12 E18

Refer to 4.1.1Heating, Ventilation and Air Conditioning

Power Supply/Sensor/Actuator





Refer to 4.1.1Heating, Ventilation and Air Conditioning Compressor Control/

Sensor

Refer to 4.2.11On-board Network

System DLC

Refer to 3.1.7 Fuel System3.1.8 Ignition System 3.1.10 Charging System

ECM

67

65

68

69

IR05

16 E18

12 X05

2.0

RD

/BU

2.0 RD/BU

2.0

RD

/BU

2.0

RD

/BU

1.25

RD

/BU

0.5

RD

/BU

8 E18 51 E18

1 X05

0.5

BN/W

H0.

5 BN

/WH

32 E18

15 X05

0.5

BU0.

5 BU

17 E18

11 X05

M3112001

3.1.12-3

M201 2014.01


HO2S/EVAP

Main Fuse Box P01

0.5

YE0.

5 YE

0.5

YE

7 X04

16 X05

0.85

RD

/BU

0.85

RD

/WH

2 E13

1 E13 4 E01 2 E01

3 E01 1 E01

I/P Fuse Box P40


Front Oxygen Sensor

8.0

WH

8.0

WH

8.0

WH

8.0

WH

+B

2 IF15

15A

29

30

IF30

15A

59

60

1

EF01

80A

67

65

68

69

IR05

ECM

0.5

BN/W

H0.

5 BN

/WH

32 E18 37 E18 2 E18

15 X05

2.0

RD

/BU

1.25

RD

/BU

1.25

RD

/GN

1.25

RD

/GN

0.85

RD

/GN

0.85

YE/

WH

45 E18

0.5

BK/O

G

2.0

RD

/BU

2.0

RD

/BU

1 X056 X05

3 S14 4 S14

1 S14 2 S14

Rear Oxygen Sensor

4 E1839 E18

1.25

RD

/GN

1.25

RD

/GN

0.5

YE/G

N

0.5

YE/G

N

0.5

YE/G

N

0.5

YE/G

N

0.5

YE/G

N

0.5

WH

/RD

0.5

WH

/RD

0.85

WH

29 E18

6 X04

19 X04

17 X04

22 X05

10 X05

Refer to 3.1.12Electronic Control System

TPS/KS/IAC

M3112002

M201 2014.01


• Operating circuit analysis of carbon canister solenoid is as follows:

Current from the battery positive → Main fuse box (main fuse EF01) → I/P fuse box (main relay fuseIF15) → Main relay-terminal 68 → Main relay closing contact → Main relay-terminal 69 → ConnectorX05-terminal 1→Carbon canister solenoid connector E13-terminal 1→Carbon canister solenoid coil→ Carbon canister solenoid connector E13-terminal 2 → ECM connector E18-terminal 37 → ECM →

Grounding

Carbon canister solenoid coil is powered on to start work.

• Operating circuit analysis of front oxygen sensor is as follows:

Current from the battery positive → Main fuse box (main fuse EF01) → I/P fuse box (main relay fuseIF15)→Main relay-terminal 68→Main relay closing contact→Main relay-terminal 69→ I/P fuse box(oxygen sensor fuse IF30) → Connector X05-terminal 6 → Front oxygen sensor connector E01-terminal 4 → Front oxygen sensor (heating resistor) → Front oxygen sensor connector E01-terminal3 → ECM connector E18-terminal 2 → ECM → Grounding

Controlled by ECM directly, front oxygen sensor (heating resistor) is powered on to start work.

Signal from front oxygen sensor → Front oxygen sensor connector E01-terminal 2 → ECM connectorE18-terminal 39 → ECM and front oxygen sensor → Front oxygen sensor connector E01-terminal 1→ ECM connector E18-terminal 45 → ECM

• Operating circuit analysis of rear oxygen sensor is as follows:

Current from the battery positive → Main fuse box (main fuse EF01) → I/P fuse box (main relay fuseIF15)→Main relay-terminal 68→Main relay closing contact→Main relay-terminal 69→ I/P fuse box(oxygen sensor fuse IF30) → Connector X04-terminal 6 → Rear oxygen sensor connector S14-terminal 3 → Rear oxygen sensor (heating resistor) → Rear oxygen sensor connector S14-terminal 1→ Connector X04-terminal 17 → Connector X05-terminal 10 → ECM connector E18-terminal 4 →

ECM → Grounding

Controlled by ECM directly, rear oxygen sensor (heating resistor) is powered on to start work.

Signal from rear oxygen sensor → Rear oxygen sensor connector S14-terminal 2 → Connector X04-terminal 7 → ECM connector E18-terminal 29 → ECM and rear oxygen sensor → Connector X04-terminal 19 → Connector X05-terminal 22 → ECM connector E18-terminal 39 → ECM

3.1.12-5

M201 2014.01


TPS/KS/IAC

0.5

GY/

GN

ECM


HO2S/EVAP

26 E18

22 E18

0.5

GY/

BK

36 E18

0.5

GY

35 E18

0.5

GY/

YE

21 E18

1 E14 4 E14 3 E14 2 E14

0.5

BU/W

H

39 E18

0.5

YE/G

N

18 E18

0.5

BU/B

N

30 E18

0.5

RD

31 E18

0.5

GN

2.0

BK0.

5 BK0.5

YE/G

N

0.5 YE/GN

Throttle Position Sensor Knock Sensor

3 E16 2 E16 1 E12 3 E121 E16 2 E12

G301

Stepper Motor

M3112003

M201 2014.01


• Operating circuit analysis of throttle position sensor is as follows:

Current from ECM → ECM connector E18-terminal 18 → Throttle position sensor connector E16-terminal 2 → Throttle position sensor → Throttle position sensor connector E16-terminal 1 → ECMconnector E18-terminal 39 → ECM → Grounding

Position signal from throttle position sensor → Throttle position sensor connector E16-terminal 3 →

ECM connector E18-terminal 26 → ECM

• Operating circuit analysis of knock sensor is as follows:

Signal from knock sensor → Knock sensor connector E12-terminal 2 → ECM connector E18-terminal31 → ECM and knock sensor → Knock sensor connector E12-terminal 1 → ECM connector E18-terminal 30 → ECM

• Operating circuit analysis of stepper motor is as follows:

Stepper motor is powered on by four phases alternately, and rotating direction is determined by thepower supplying order of four phases.

When A phase is working, current from ECM → ECM connector E18-terminal 22 → Stepper motorconnector E14-terminal 1 → Stepper motor → Stepper motor connector E14-terminal 4 → ECMconnector E18-terminal 36 → ECM → Grounding

When B phase is working, current from ECM → ECM connector E18-terminal 21 → Stepper motorconnector E14-terminal 2 → Stepper motor → Stepper motor connector E14-terminal 3 → ECMconnector E18-terminal 35 → ECM → Grounding

When C phase is working, current from ECM → ECM connector E18-terminal 35 → Stepper motorconnector E14-terminal 3 → Stepper motor → Stepper motor connector E14-terminal 2 → ECMconnector E18-terminal 21 → ECM → Grounding

When D phase is working, current from ECM → ECM connector E18-terminal 36 → Stepper motorconnector E14-terminal 4 → Stepper motor → Stepper motor connector E14-terminal 1 → ECMconnector E18-terminal 22 → ECM → Grounding

3.1.12-7

M201 2014.01


CKP/Evaporator Thermistor/ECT/IAT

0.5

BU/G

N

ECM

25 E18

2 E15

0.5

BU/R

D0.

5 BU

/RD

40 E18

1 E15

0.5

YE/B

N

59 E18

4 E15

0.5

YE/B

K0.

5 YE

/BK

19 E18

3 E15

0.5

BU/R

D

1 E11

0.5

BN/Y

E

41 E18

2 E11

Air Intake Pressure/Temperature SensorCoolant Temperature

SensorEvaporatorThermistorCrankshaft Position Sensor

0.5

LG/B

K0.

5 LG

/BK

13 E18

2 P39

0.5

BU/R

D0.

5 BU

/RD

1 P39

0.5

BU/R

D

3 E17

0.5

BU/W

H

47 E18

2 E17

0.5

YE/B

K

1 E17

21 X05 14 X05

0.5

YE

/GN

57 E18

Refer to 4.2.2 Instrument Cluster

Signal Lamp


Signal Lamp


Signal Lamp


Power Supply and Signal

Refer to 4.2.6 Lighting System

Headlamp

Refer to 4.2.11 On-board Network

System

0.5

LG/W

H

15 E18

0.5

WH

/BU

9 E18

0.5

YE

/WH

56 E18

0.5

VT/

YE

20 E18

0.5

RD

/YE

24 E18

M3112004

M201 2014.01


• Operating circuit analysis of crankshaft position sensor is as follows:

Current from ECM → ECM connector E18-terminal 19 → Crankshaft position sensor connector E17-terminal 1 → Crankshaft position sensor → Crankshaft position sensor connector E17-terminal 3 →

ECM connector E18-terminal 40 → ECM → Grounding

Position signal from crankshaft position sensor→Crankshaft position sensor connector E17-terminal2 → ECM connector E18-terminal 47 → ECM

• Operating circuit analysis of air intake pressure/temperature sensor is as follows:

Current from ECM → ECM connector E18-terminal 19 → Air intake pressure/temperature sensorconnector E15-terminal 3 → Air intake pressure/temperature sensor → Connector E15-terminal 1 →

ECM connector E18-terminal 40 → ECM → Grounding

Air intake temperature signal from air intake pressure/temperature sensor → Air intake pressure/temperature sensor connector E15-terminal 2 → ECM connector E18-terminal 25 → ECM

Air intake pressure signal from air intake pressure/temperature sensor → Air intake pressure/temperature sensor connector E15-terminal 4 → ECM connector E18-terminal 59 → ECM

• Operating circuit analysis of evaporator thermistor is as follows:

Current from ECM → ECM connector E18-terminal 13 → Connector X05-terminal 14 → Evaporatorthermistor connector P39-terminal 2→Evaporator thermistor→Evaporator thermistor connector P39-terminal 1 → Connector X05-terminal 21 → ECM connector E18-terminal 40 → ECM → Grounding

• Operating circuit analysis of coolant temperature sensor is as follows:

Current from ECM→ECM connector E18-terminal 41→Coolant temperature sensor connector E11-terminal 2 → Coolant temperature sensor → Coolant temperature sensor connector E11-terminal 1→ ECM connector E18-terminal 40 → ECM → Grounding

3.1.12-9

M201 2014.01


Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

M201 2014.01




1 2 3 4 5 67 8 9 10

11 12 13 14 15 16

17 18 19 2021 22 23 24 25 26

12345678910

11121314151617181920

212223242526

X04

1 7 8 9 10 411 12 13 14

2 15 16 17 18 5

19 20 21 223 23 24 25 26 6

1

2

3

7

11

15

19

23

8

12

16

20

24

9

13

17

21

25

10

14

18

22

26

4

5

6

X05

3.1.12-11

M201 2014.01


Front Oxygen Sensor Coolant Temperature Sensor

Knock Sensor Carbon Canister Solenoid

Stepper Motor Air Intake Pressure/Temperature Sensor

1

2

3

4

E01

1 2

E11

1 2 3

E12

1 2

E13

4321

E14

1 2 3 4

E15

M201 2014.01


Throttle Position Sensor Crankshaft Position Sensor

ECM

Rear Oxygen Sensor Evaporator Thermistor

1 2 3

E16

1 2 3

E17

7 8

5 6

3 4

1 2

51 52 53 54 55 56 57 58 59 60 61 62 63 64

37 38 39 40 41 42 43 44 45 46 47 48 49 50

23 24 25 26 27 28 29 30 31 32 33 34 35 36

9 10 11 12 13 14 15 16 17 18 19 20 21 22

E18

12

34

S14

12

P39

M201 2014.01

4.1.1-1 4.1.1-1Heating, Ventilation and Air Conditioning

Heating, Ventilation and Air Conditioning

M4101004

HeaterMotor

GovernorResistor

A/C Controller

4

10

6

8

7

5

2

2

11 3

2 2134

4

1

IG2

B+

IF26

IF33

IR02

G1031

2

G106

OverheadBlower

Lighting CombinationSwitch Terminal 8

Tristate Pressure

Switch

Overhead Blower Resistor Overhead Evaporator

Diode

Compressor

EvaporatorThermistor

392

44

12

10

61

1

1

2

G106

3 4

12

G105

ECM

40

13

1

2

Relay IR05Terminal 69

B+IF08

IR01

4.1.1 Heating, Ventilation and Air Conditioning

4.1.1-2

M201 2014.01

4.1.1-2Heating, Ventilation and Air Conditioning

Compressor and Sensor Control Operation

M4101001

IF15

15A

8.0

WH

8.0

WH

2.0

WH

/YE

2.0

WH

/YE

2.0

RD

/BU

0.5

BN/W

H0.

5 BN

/WH

0.85

OG

0.5

BK/Y

E0.

5 BK

/YE0.

5 BU

/RD

0.5

BU/R

D

0.5

LG/B

K0.

5 LG

/BK

0.5

RD

/BU

0.5

WH

/YE

8.0

WH

+B

2

29

30

1EF

01

80A

I/P Fuse Box P40

67

65

68

69

47 48

49

1

IF18

10A

35

36

IR01

Compressor


45

IR05

15 X05 24 X05

21 X05

32 E18 61

ECM

E1840 E18

14 X05

13 E18

1 P39 2 P39

P02

Main Fuse Box P01

M201 2014.01


• Operating circuit analysis of compressor is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (compressor fuseIF18) → Compressor relay-terminal 48 → Compressor relay closing contact → Compressor relay-terminal 49 → Compressor connector P02-terminal 1 → Compressor → Grounding

The compressor starts to work when electromagnetic clutch is engaged.

4.1.1-4

M201 2014.01


Power Supply/Sensor/Actuator3.

0 BK

2.0

BK

G106

IR02

A/C Controller

A/C

Sw

itch

Hea

ter

Switc

h

7 P264 8 P265 P26

10 P26

6 P26

1 P38 2 P38 4 P38

I/P Fuse Box P40

HeaterMotor

Governor Resistor

Main Fuse Box P01

IG2

3.0

BK/B

U

0.5

BK/W

H0.

5 BK

/WH

0.5 BK/WH

IF41

82

81

20A

IF26

52

51

20A

53

54

52

50

3.0

BK0.

5 BK

2.0

RD

/GN

2.0

RD

/GN

2.0

RD

/GN

2.0

RD

/GN

2.0 GN/WH

2.0 PK/BU2.0

PK/B

U

0.5

RD

/YE

2.0

PK

2.0

YE

G103

2 P28

M

1 P28

8.0

WH

8.0

WH

8.0

WH

+B

2

1

EF01

80A

34

33

IF1730A

P26

Refer to 4.2.6Lighting System

Position Lamp and License Plate Lamp

ECM

3 X03

A

0.5

GN

/BU

Tristate Pressure Switch

1 P09

0.5

BK

0.5

BU/B

K0.

5 BU

/BK

2 P09

G105

3 P09 4 P09

10 E18

8 X05

2 P263 P26

0.5

PK/B

K0.

5 PK

/BK

44 E18

20 X05

Diode

0.5

PK/W

H

0.5

PK/W

H

0.5

LG/R

D

2 P22

1 P22

7 X05

9 P26

12 E18

M4101002

M201 2014.01


OFF

Low

2.0

BK/Y

E2.

0 BK

/YE

0.85

LU

0.85

VT

2.0 BK/YE

2.0

BK2.

0 BK

2.0

BK

G106

Overhead Evaporator Switch

Overhead Blower

Overhead Blower Resistor

2 L03

1 L03

1 L04

3 L042 L04

4 L05 3 L05

2 L05

1 L05

2.0

BK/R

D

1 X08

4 X03

2 X08

High Medium

2.0

RD

/GN

A

M

M4101003

4.1.1-6

M201 2014.01


• Operating circuit analysis of tristate pressure switch is as follows:

Current from ECM→ECM connector E18-terminal 44→Connector X05-terminal 20→A/C controllerconnector P26-terminal 2 → A/C switch (closing contact) → A/C controller connector P26-terminal 3→ Tristate pressure switch connector P09-terminal 1 → Tristate pressure switch (closing contact) →Tristate pressure switch connector P09-terminal 2 → A/C controller connector P26-terminal 9 → A/Ccontroller heater switch (speed closing contact) → A/C controller connector P26-terminal 10 →

Grounding G106

Current from ECM→ECM connector E18-terminal 10→Connector X05-terminal 8→Tristate pressureswitch connector P09-terminal 4 → Tristate pressure switch (medium pressure closing contact) →

Tristate pressure switch connector P09-terminal 3 → Grounding G106

• Operating circuit analysis of heater is as follows:

High speed: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (Heater& overhead evaporator fuse IF17)→Heater relay-terminal 53→Heater relay closing contact→Heaterrelay-terminal 54→Heater motor connector P28-terminal 1→Heater motor→Heater motor connectorP28-terminal 2 → A/C controller connector P26-terminal 6 → Heater switch (high speed contact) →A/C controller connector P26-terminal 10 → Grounding G106

Medium speed: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box(Heater & overhead evaporator fuse IF17)→ Heater relay-terminal 53 → Heater relay closing contact→Heater relay-terminal 54→Heater motor connector P28-terminal 1→Heater motor→Heater motorconnector P28-terminal 2 → Governor resistor connector P38-terminal 4 → Governor resistor →

Governor resistor connector P38-terminal 2 → A/C controller connector P26-terminal 8 → Heaterswitch (medium speed contact) → A/C controller connector P26-terminal 10 → Grounding G106

Low speed: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (Heater& overhead evaporator fuse IF17)→Heater relay-terminal 53→Heater relay closing contact→Heaterrelay-terminal 54→Heater motor connector P28-terminal 1→Heater motor→Heater motor connectorP28-terminal 2→Governor resistor connector P38-terminal 4→Governor resistor→Governor resistorconnector P38-terminal 1 → A/C controller connector P26-terminal 7 → Heater switch (low speedcontact) → A/C controller connector P26-terminal 10 → Grounding G106

Heater motor is controlled by the heater switch, whose speed can be changed through changing thecurrent magnitude of motor.

• Operating circuit analysis of overhead blower is as follows:

High speed: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (Heater& overhead evaporator fuse IF17)→Heater relay-terminal 53→Heater relay closing contact→Heaterrelay-terminal 54 → Connector X03-terminal 3 → Connector X08-terminal 1 → Overhead blowerconnector L03-terminal 2 → Overhead blower → Overhead blower connector L03-terminal 1 →

Overhead evaporator switch connector L05-terminal 4 → Overhead evaporator switch (high speed contact) → Overhead evaporator switch connector L05-terminal 2 → Connector X08-terminal 2 → Connector X03-terminal 4 → Grounding G106

M201 2014.01


Medium speed: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box(Heater & overhead evaporator fuse IF17) → Heater relay-terminal 53 → Heater relay closing contact→ Heater relay-terminal 54 → Connector X03-terminal 3 → Connector X08-terminal 1 → Overheadblower connector L03-terminal 2 → Overhead blower → Overhead blower connector L03-terminal 1→Overhead blower resistor connector L04-terminal 1→Overhead blower resistor→Overhead blowerresistor connector L04-terminal 2 → Overhead evaporator switch connector L05-terminal 3 →

Overhead evaporator switch (medium speed contact) → Overhead evaporator switch connector L05-terminal 2 → Connector X08-terminal 2 → Connector X03-terminal 4 → Grounding G106

Low speed: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (Heater& overhead evaporator fuse IF17)→Heater relay-terminal 53→Heater relay closing contact→Heaterrelay-terminal 54 → Connector X03-terminal 3 → Connector X08-terminal 1 → Overhead blowerconnector L03-terminal 2 → Overhead blower → Overhead blower connector L03-terminal 1 →Overhead blower resistor L04-terminal 1 → Overhead blower resistor → Overhead blower resistorconnector L04-terminal 3 → Overhead evaporator switch connector L05-terminal 1 → Overheadevaporator switch (low speed contact) → Overhead evaporator switch connector L05-terminal 2 →

Connector X08-terminal 2 → Connector X03-terminal 4 → Grounding G106

Overhead blower is controlled by the overhead blower switch, whose speed can be changed bychanging the current magnitude of motor.

4.1.1-8

M201 2014.01


Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

M201 2014.01


I/P Wiring Harness to Roof Wiring Harness Roof Wiring Harness to I/P Wiring Harness


4 3 2 1

1 2 3 4

X03

1 7 8 9 10 411 12 13 14

2 15 16 17 18 5

19 20 21 223 23 24 25 26 6

1

2

3

7

11

15

19

23

8

12

16

20

24

9

13

17

21

25

10

14

18

22

26

4

5

6

X05

4.1.1-10

M201 2014.01


Roof Wiring Harness to Overhead Evaporator Wiring Harness

Overhead Evaporator Wiring Harness to Roof Wiring Harness

Compressor Tristate Pressure Switch

Diode A/C Controller

1

2

1

2

X08

1

P02

1

243

P09

1

2

P22

12345

678910

P26

M201 2014.01


Heater Motor Governor Resistor


ECM

1

2

P28

12

34

P38

12

P39

7 8

5 6

3 4

1 2

51 52 53 54 55 56 57 58 59 60 61 62 63 64

37 38 39 40 41 42 43 44 45 46 47 48 49 50

23 24 25 26 27 28 29 30 31 32 33 34 35 36

9 10 11 12 13 14 15 16 17 18 19 20 21 22

E18

4.1.1-12

M201 2014.01


Overhead Evaporator Blower Blower Resistor

Blower Switch

1

2

L03

3

1

2

L04

12

34

L05

M201 2014.01

4.2.2-1 4.2.2-1Instrument Cluster

Instrument Cluster

M4202004

8B+IF07

7

11

24

1 3

IG1IF35

IF33

G104

G104

G104

Instrument Cluster

VehicleSpeedSensor2

Engine Oil Pressure Switch

Relay IR06Terminal 74

Front Left DoorSignal Lamp Switch

Front Right DoorSignal Lamp Switch

Rear Left DoorSignal Lamp Switch

Rear Right DoorSignal Lamp Switch

231

Fuel LevelSensor

AlternatorTerminal 3

110 3

Parking Brake Switch

Brake Fluid Level Switch

27

22

ECM

1

21

G104

Seat Belt Switch

21

13

18

9

56

129

557

2820

G202

Lighting Combination Switch

817

111

132

219

104

93

20

21

1

1

1

1

4.2.2 Instrument Cluster

4.2.2-2

M201 2014.01

4.2.2-2Instrument Cluster

Power Supply and Signal

Main Fuse Box P01

+B

2

18.0

WH

EF01

80A

Instrument Cluster

2 X05

0.3

YE

/BK

0.5

YE

/BK

18 X05

0.3

VT/

YE

0.5

VT/

YE

1 E10Engine OilPressureSwitch

SeatBeltSwitch

5 X04

BA

0.3

GY

/BK

0.5

GY

/BK

0.5

BK

2 S05

1 S05

9 X04

0.3

WH

/RD

0.3

RD

/BK

0.3

RD

/BK

0.3

RD

/BK

0.5

RD

/BK

8 P21 7 P21

24 P21 27 P21

2 P19

1 P19

23 P21 28 P21 22 P21

IF35

10A

70

69

0.3

BK0.

5 BK

IF33

10A

IG1

66

65

3.0

YE/B

K0.

5 YE

/BN

0.5

GN

/BK

G104 G202

I/P Fuse Box P40

Refer to 4.2.5 Information andEntertainment System 4.2.6 Lighting System Roof Lamp

Refer to 3.1.10Charging System


BatteryChargingIndication

Brake Fluid LevelParking Brake

Engine Oil Pressure Engine Fault

Seat Belt Unfastened Warning

BrakeFluidLevelSwitch

1 S18

ParkingBrakeSwitch

IF07

10A

8.0

WH

8.0

WH

0.5

WH

0.5

WH

13

14

C

M4202001

M201 2014.01


• Operating circuit analysis of brake fluid level and parking brake indicator is as follows:

Brake fluid level indicator: Current from battery positive→Main fuse box (main fuse EF01)→ I/P fusebox (ignition switch 1 fuse IF01) → Ignition switch connector P31-terminal 3 → Ignition switch IG1contact → Ignition switch connector P31-terminal 2 → I/P fuse box (instrument cluster fuse IF35) →Instrument cluster connector P21-terminal 7 → Instrument cluster (brake fluid level indicator) →

Instrument cluster connector P21-terminal 27 → Brake fluid level switch connector P19-terminal 2 →

Brake fluid level switch (closing contact) → Brake fluid level switch connector P19-terminal 1 →

Grounding G104

Parking brake indicator: Current from battery positive → Main fuse box (main fuse EF01) → I/P fusebox (ignition switch 1 fuse IF01) → Ignition switch connector P31-terminal 3 → Ignition switch IG1contact → Ignition switch connector P31-terminal 2 → I/P fuse box (instrument cluster fuse IF35) →Instrument cluster connector P21-terminal 7 → Instrument cluster (brake fluid level indicator) →

Instrument cluster connector P21-terminal 27 → Connector X04-terminal 5 → Parking brake switchconnector S18-terminal 1 → Parking brake switch (closing contact) → Grounding

The indicator is used as brake fluid level indicator and parking brake indicator at the same time.

• Operating circuit analysis of engine oil pressure warning lamp is as follows:

Current from battery positive→Main fuse box (main fuse EF01)→ I/P fuse box (ignition switch 1 fuseIF01) → Ignition switch connector P31-terminal 3 → Ignition switch IG1 contact → Ignition switchconnector P31-terminal 2→I/P fuse box (instrument cluster fuse IF35)→Instrument cluster connectorP21-terminal 7 → Instrument cluster (engine oil pressure warning lamp ) → Instrument clusterconnector P21-terminal 23→Connector X05-terminal 2→Engine oil pressure switch connector E10-terminal 1 → Engine oil pressure switch (closing contact) → Engine cylinder block grounding

The engine oil pressure warning lamp is turned on.

• Operating circuit analysis of seat belt unfastened warning lamp is as follows:

Current from battery positive→Main fuse box (main fuse EF01)→ I/P fuse box (ignition switch 1 fuseIF01) → Ignition switch connector P31-terminal 3 → Ignition switch IG1 contact → Ignition switchconnector P31-terminal 2→I/P fuse box (instrument cluster fuse IF35)→Instrument cluster connectorP21-terminal 7 → Instrument cluster (seat belt unfastened warning lamp ) → Instrument clusterconnector P21-terminal 22 → Connector X04-terminal 9 → Seat belt switch connector S05-terminal2→Seat belt switch (closing contact)→Seat belt switch connector S05-terminal 1→Grounding G202

The seat belt unfastened warning lamp is turned on.

4.2.2-4

M201 2014.01


Signal Lamp

S

0.3

YE

/RD

0.3

YE

/RD

0.5

YE

/RD

0.5

BK

/YE

0.5 BK/YE

0.3

YE

/WH

0.3

WH

/BU

0.3

YE

/GN

0.3

GN

0.3

GN

0.5

YE

/WH

0.5

WH

/BU

0.5

YE

/GN

ECM

Instrument Cluster

B

C

A

A

10 P21 13 P21 12 P21 5 P21

56 E183

2

S01

1 S01

9 E18 57 E18 1 S12

2 S12

3 S12

11 P21 9 P21

0.5

BK0.

5 BK

0.5

BK

G104

Vehicle SpeedSignal

Vehicle SpeedSensor

FuelLevel

Sensor

Engine SpeedSignal

Fuel LevelSignal

Coolant TemperatureSignal

Control Unit Inside Instrument Cluster

Buzzer

3 X0518 X04

1 X07

X07

9 X05 26 X05 20 X043 X04

10 X04

0.5

BK

0.5

YE/B

N0.

5 YE

/BN

M4202002

M201 2014.01


• Operating circuit analysis of fuel level signal is as follows:

Current from instrument cluster → Instrument cluster connector P21-terminal 10 → Connector X04-terminal 18 → Connector X07-terminal 1 → Fuel level sensor connector S01-terminal 3 → Fuel levelsensor→Fuel level sensor connector S01-terminal 1→Connector X07-terminal 2→Connector X04-terminal 10 → Grounding G104

• Operating circuit analysis of engine coolant temperature signal is as follows:

Signal from ECM→ECM connector E18-terminal 56→Connector X05-terminal 3→Instrument clusterconnector P21-terminal 13 → Instrument cluster (control unit inside instrument cluster)

• Operating circuit analysis of engine speed signal is as follows:

Signal from ECM→ECM connector E18-terminal 9→Connector X05-terminal 9→ Instrument clusterconnector P21-terminal 12 → Instrument cluster (control unit inside instrument cluster)

• Operating circuit analysis of vehicle speed signal is as follows:

Output: Signal from instrument cluster (control unit inside instrument cluster) → Instrument clusterconnector P21-terminal 5 → Connector X05-terminal 26 → ECM connector E18-terminal 57 → ECM

Input: Signal from vehicle speed sensor → Vehicle speed sensor connector S12-terminal 3 →

Connector X04-terminal 20 → Instrument cluster connector P21-terminal 11 → Instrument cluster (control unit inside instrument cluster)

4.2.2-6

M201 2014.01


Lighting Signal Lamp

0.5

RD

/YE

0.3

RD

/YE

0.3

RD

/WH

1.25

RD

/WH

Refer to 4.2.6Lighting SystemPosition Lamp

Refer to 4.2.6Lighting SystemTurn signal lamp

Low BeamIndicator

High BeamIndicator

Door OpenIndicator

BackgroundLamp

Indicator Right TurnIndicator

Left TurnIndicator

Front FogIndicator

RearFogIndicator

0.3

RD

1.25

RD

0.3

BK

/RD

0.5

BK

/RD

0.5

GN

/YE

0.3

GN

/YE

0.5

GN

/RD

0.3

GN

/RD

1.25

LG

0.3

LG

0.5

GY

0.3

GY

Instrument Cluster

A

4 P21 3 P21 21 P21 18 P21

17 P21 1 P21 2 P21 20 P21 19 P21

0.5

BK0.

5 BK

G104


Fog Lamp


Headlamp


Roof Lamp

M4202003

M201 2014.01


Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

4.2.2-8

M201 2014.01




1 2 3 4 5 67 8 9 10

11 12 13 14 15 16

17 18 19 2021 22 23 24 25 26

12345678910

11121314151617181920

212223242526

X04

1 7 8 9 10 411 12 13 14

2 15 16 17 18 5

19 20 21 223 23 24 25 26 6

1

2

3

7

11

15

19

23

8

12

16

20

24

9

13

17

21

25

10

14

18

22

26

4

5

6

X05

M201 2014.01


Chassis Wiring Harness to Fuel Pump Wiring Harness Fuel Pump Wiring Harness to Chassis Wiring Harness

Engine Oil Pressure Switch Brake Fluid Level Switch

Instrument Cluster

13

24

1

2

3

4

X07

1

E10

12

P19

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

26 27 28 29 30 31 3217 18 19 20 21 22 23 24 25

P21

4.2.2-10

M201 2014.01


Fuel Pump Seat Belt Switch

Vehicle Speed Sensor Parking Brake Switch

ECM

1

2

3

4

S01

1

2

S05

1 2 3

S12

1

S18

7 8

5 6

3 4

1 2

51 52 53 54 55 56 57 58 59 60 61 62 63 64

37 38 39 40 41 42 43 44 45 46 47 48 49 50

23 24 25 26 27 28 29 30 31 32 33 34 35 36

9 10 11 12 13 14 15 16 17 18 19 20 21 22

E18

4.2.3-1

M201 2014.01

4.2.3-1Horn

Horn

Main Fuse Box P01

P12

2

1

P12

IF12

15A

8.0

WH

8.0

WH

8.0

WH

0.85

RD

0.85

RD

0.5

RD

0.5

YE

0.85

WH

/GN

0.85

BK

2.0

BK

+B

2

23

24

8887

85 89

1EF

01

80A

I/P Fuse Box P40

IR09

Horn SwitchHorn

1 P32

G105

M4203001

4.2.3 Horn

M201 2014.01

4.2.3-2 4.2.3-2Horn

• Operating circuit analysis of horn is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P box (horn fuse IF12) → Hornrelay-terminal 88 → Horn relay closing contact → Horn relay-terminal 89 → Horn connector P12-terminal 2 → Horn → Horn connector P12-terminal 1 → Grounding G105

Controlled by the horn switch through horn relay, horn is powered on to work.

4.2.3-3

M201 2014.01

4.2.3-3Horn

Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

M201 2014.01

4.2.3-4 4.2.3-4Horn

Electrical Horn Horn Switch

12

P12

1

P32

4.2.4-1

M201 2014.01

4.2.4-1Cigarette Lighter

Cigarette Lighter

1 P37

1 P36

1.25

BK

2.0

BK1.

25 W

H/B

K1.

25 W

H/B

K

1.25 WH/BK0.85 WH/BKIF

40

80

79

15A

ACC

1.25

BU

G106

I/P Fuse Box P40

CigaretteLighter

Refer to 4.2.5Information and

Entertainment System

Refer to 4.2.10Body Control System

M4204001

4.2.4 Cigarette Lighter

M201 2014.01

4.2.4-2 4.2.4-2Cigarette Lighter

• Operating circuit analysis of cigarette lighter is as follows:

Current from battery positive→Main fuse box (main fuse EF01)→ I/P fuse box (ignition switch 2 fuseIF02) → Ignition switch connector P31-terminal 4 → Ignition switch ACC contact → Ignition switchconnector P31-terminal 1 → I/P fuse box (cigarette lighter & radio fuse IF40) → Cigarette lighterconnector P37-terminal 1 → Cigarette lighter → Cigarette lighter connector P36-terminal 1 →

Grounding G106

4.2.4-3

M201 2014.01

4.2.4-3Cigarette Lighter

I/P Fuse Box

Cigarette Lighter Negative Cigarette Lighter Positive

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

1

P36

1

P37

4.2.5-1

M201 2014.01

4.2.5-1Information and Entertainment System

Information and Entertainment System

M4205003

Lighting Combination

SwitchTerminal 8

6 3

8

2

1

5ACCIF40

1

4

G106

B+IF07

Front Left Speaker

RADIO

2

7

2

1 Front Right Speaker

Antenna

4.2.5 Information and Entertainment System

M201 2014.01

4.2.5-2 4.2.5-2Information and Entertainment System

Power Supply

M4205001

Main Fuse Box P01 I/P Fuse Box P40

+B

2

1

8.0

WH

8.0

WH

0.5

WH

0.5

WH

0.5

WH

1.25

WH

/BK

Antenna

1.25

WH

/BK

0.5

WH

1.25

WH

/BK

0.85

WH

/BK

8.0

WH


Roof Lamp

Refer to 4.2.2Instrument

Cluster

Refer to 4.2.10Body Control System

Refer to 4.2.4Cigarette Lighter

IF07

10A

13

14

IF40

80

79

15A

ACC

1.25

BU

2.0

BK0.

85 B

K

P34

RADIO

P34ACC

GND

P34+B

1 5

G106

4

EF01

80A

4.2.5-3

M201 2014.01


Speaker

M4205002

0.5

RD

/YE


P34 P34

0.5

RD

0.5

RD

0.5

RD

/BK

0.5

RD

/BK

0.5

BU/R

D0.

5 BU

/RD

0.5

BU/B

K0.

5 BU

/BK

P3423P346 8 7 P34

2 1 D05D04D04

R_RFR_RFL_RFL_RF

RADIO

1

12

X022 X01 3 X01 2 X02

Front Right SpeakerFront Left Speaker

D05

M201 2014.01


• Operating circuit analysis of radio is as follows:

Memory power: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (rooflamp fuse IF07) → Radio connector P34-terminal 1 → Radio → Radio connector P34-terminal 4 →

Grounding G106

Energizing power: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box(ignition switch 2 fuse IF02)→ Ignition switch connector P31-terminal 4→ Ignition switch ACC contact→Ignition switch connector P31-terminal 1→I/P fuse box (cigarette lighter & radio fuse IF40)→Radioconnector P34-terminal 5 → Radio → Radio connector P34-terminal 4 → Grounding G106

Radio can start to work only when both powers supply.

• Operating circuit analysis of speaker is as follows:

Front left speaker：Radio → Radio connector P34-terminal 3 → Connector X01-terminal 2 → Frontleft speaker connector D04-terminal 2 → Front left speaker → Front left speaker connector D04-terminal 1 → Connector X01-terminal 3 → Radio connector P34-terminal 8 → Radio

Front right speaker：Radio → Radio connector P34-terminal 2 → Connector X02-terminal 1 → Frontright speaker connector D05-terminal 2 → Front right speaker → Front right speaker connector D05-terminal 1 → Connector X02-terminal 2 → Radio connector P34-terminal 7 → Radio

4.2.5-5

M201 2014.01


Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

M201 2014.01


Radio Front Left Speaker

Front Right Speaker

I/P Wiring Harness to Front Left Door Wiring Harness Front Left Door Wiring Harness to I/P Wiring Harness

123

478 56

P34

1

2

D04

1

2

D05

1 2 4 53

6 7 11 128 9 10

34

11 10 812

5

7 69

2 1

X01

4.2.5-7

M201 2014.01


I/P Wiring Harness to Front Right Door Wiring Harness Front Right Door Wiring Harness to I/P Wiring Harness

1 2 4 53

6 7 11 128 9 10

34

11 10 812

5

7 69

2 1

X02

4.2.6-1

M201 2014.01

4.2.6-1Lighting System

Lighting System

M4206010

Right License Plate Lamp

Diode A

5

109

3

2

B+

IF09

5

6 4

5

6 4

3 4

IR06

IF08 IF14IF16

Ligh

ting

Com

bina

tion

Switc

h

RightHeadlamp

LeftHeadlamp

InstrumentCluster

Terminal 17

G103

G106G103G202G201

InstrumentCluster

Front Right Turn Lamp

Rear Right Turn Lamp

Front Left Turn Lamp

Rear Left Turn Lamp

Flasher Relay

InstrumentCluster

Diode B

1224 ECM

Right Low Beam Regulator Motor

Left Low Beam Regulator Motor

1

1 2

2

3

3

3

3 2

1

A/C ControllerTerminal 5

RadioTerminal 6

1

LightingPowerControlSwitch

Front Left Position Lamp

Front Right Position Lamp

Rear Left Position Lamp

Rear Right Position Lamp

Left License Plate Lamp

145

2

G106

G103

6 8

3 2

G105 1 4

G201 1 4

G2022 1

2 1

G201

1

2

1

2

RearLeftFogLamp

RearRightFogLamp

FrontLeftFogLamp

FrontRightFogLamp

1

2

1

2

19

1

1 2

3 1

1 2

3

1

2

8

3

1

76

11

2

20Central Lock

Controller

G105

G20213

12

G103

HazardWarning

LampSwitch

G201

G105

4

G106

13

2

7

6

5

B+IF21

IG1IF33

4.2.6 Lighting System

M201 2014.01

4.2.6-2 4.2.6-2Lighting System

Headlamp

Main Fuse Box P01

P24

IF08

15A

16

15

IF09

15A

18

17

6 4P08 P08

5 P08

2.0

BK3.

0 BK

1.25

RD

/WH

1.25

RD

1.25

RD

1.25

RD

/WH

0.3

RD

0.3

RD

/WH

0.5B

K1.

25 R

D

1.25

RD

/WH

1.25

WH

/RD

1.25

WH

/BU

HI LO HI LO

7 10 9P30 P30 P30

6 4P14 P14

5 P14

IPC

3 P03

2

4 P03

ECM

24 E18

G103

OFF

10 97

I/P Fuse Box P40

8.0

WH

8.0

WH

+B

1

2

EF01

80A

0.5

RD

/WH

0.5

RD

P24

1P23

2 P23

1

0.5

RD

/YE

0.5

RD

/YE

0.5

RD

/YE

Combination Switch

Dio

de A

Dio

de B

Headlamp(Right)

Headlamp(Left)

Low BeamLamp

High BeamLamp

OvertakingLamp

A

17 X05

M4206001

4.2.6-3

M201 2014.01


Main Fuse Box P01

+B

2

1

0.5 WH/BU 0.5 WH/BU

0.5 WH/YE

0.5

BK

0.5 BK

0.5 BK

0.5 BN

0.5

RD

/YE

0.5

RD

/YE

1 P41

51ΩR

510Ω

820Ω

51Ω 0.5 YE

2 P413 P41

IF16

10A

32

31

I/P Fuse Box P40

8.0 WH

8.0

WH

8.0

WH

0.5

YE/R

D

Left Low BeamRegulator Motor

3P15

1P15

2P15

M

Right Low BeamRegulator Motor

3P07

1P07

2P07

M

Lighting PowerControl Switch

45

P41P41

6 P41

0.5

BK2.

0 BK

G106

EF01

80A

OFF

85CombinationSwitch

PositionLamp

5 P30

8 P30 A

M4206002

M201 2014.01


• Operating circuit analysis of left headlamp low beam is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (left headlamp & leftlight regulator motor fuse IF08) → Left headlamp connector P14-terminal 5 → Left headlamp (lowbeam bulb)→Left headlamp connector P14-terminal 4→Combination switch connector P30-terminal10 → Combination switch (Low beam lamp contact) → Combination switch connector P30-terminal 7→ Grounding G103

• Operating circuit analysis of left headlamp high beam is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (left headlamp & leftlight regulator motor fuse IF08) → Left headlamp connector P14-terminal 5 → Left headlamp (highbeam bulb)→Left headlamp connector P14-terminal 6→Combination switch connector P30-terminal9 → Combination switch (High beam/overtaking lamp contact) → Combination switch connector P30-terminal 7 → Grounding G103

• Operating circuit analysis of right headlamp low beam is as follows:

Current from battery positive→Main fuse box (main fuse EF01)→ I/P fuse box (right headlamp & leftlight regulator motor fuse IF09) → Right headlamp connector P08-terminal 5 → Right headlamp (lowbeam bulb) → Right headlamp connector P08-terminal 4 → Combination switch connector P30-terminal 10 → Combination switch (Low beam lamp contact) → Combination switch connector P30-terminal 7 → Grounding G103

• Operating circuit analysis of right headlamp high beam is as follows:

Current from battery positive→Main fuse box (main fuse EF01)→ I/P fuse box (right headlamp & leftlight regulator motor fuse IF09)→Right headlamp connector P08-terminal 5→Right headlamp (highbeam bulb) → Right headlamp connector P08-terminal 6 → Combination switch connector P30-terminal 9 → Combination switch (high beam/overtaking lamp contact) → Combination switchconnector P30-terminal 7 → Grounding G103

4.2.6-5

M201 2014.01


Brake Lamp

I/P Fuse Box P40Main Fuse Box P01

+B

2

1

IF10

10A

8.0

WH

8.0

WH

0.5

GN

/YE

0.5

GN

/WH

0.5

GN

/WH

0.5

GN

/WH0.

5 G

N/W

H0.

5 G

N/W

H 0.5

GN

/WH

8.0

WH

19

20

Brake LampSwitch

Rear LeftCombinationLamp

2.0

BK

G201

2 S10

1 S10

High MountedStop Lamp

0.85

BK

0.85 BK

2 D13

1 D13

Rear RightCombinationLamp

1.25

BK

1.25

BK

1.25

BK

G202

2 S08

1 S08

2 P20

1 P20

4 X04

3 X06

6 X06

EF01

80A

M4206003

M201 2014.01


• Operating circuit analysis of high mounted stop lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (brake lamp fuseIF10) → Brake lamp switch connector P20-terminal 1 → Brake lamp switch (closing contact) → Brakelamp switch connector P20-terminal 2 → Connector X04-terminal 4 → Connector X06-terminal 3 →

High mounted stop lamp connector D13-terminal 2 → High mounted stop lamp → High mounted stoplamp connector D13-terminal 1 → Connector X06-terminal 6 → Grounding G201

• Operating circuit analysis of left brake lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (brake lamp fuseIF10) → Brake lamp switch connector P20-terminal 1 → Brake lamp switch (closing contact) → Brakelamp switch connector P20-terminal 2 → Connector X04-terminal 4 → Rear left combination lampconnector S10-terminal 2→Rear left combination lamp→Rear left combination lamp connector S10-terminal 1 → Grounding G201

• Operating circuit analysis of right brake lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (brake lamp fuseIF10) → Brake lamp switch connector P20-terminal 1 → Brake lamp switch (closing contact) → Brakelamp switch connector P20-terminal 2 → Connector X04-terminal 4 → Rear right combination lampconnector S08-terminal 2 → Rear right combination lamp → Rear right combination lamp connectorS08-terminal 1 → Grounding G202

4.2.6-7

M201 2014.01


Turn Lamp

M4206004

Main Fuse Box P01

+B

2

1

IF21

15A

8.0

WH

8.0

WH

0.85

RD

/BK

8.0

WH

41

42

I/P Fuse Box P40

3.0

YE/B

K

0.85

YE

0.85

YE/

GN

0.85

GN

0.85

YE/

GN

0.5

YE/G

N

0.85 BK

0.5 BK

2.0

BK

2.0

BK

0.5

GN

/YE

0.5

GN

/RD

0.5 GN/RD

0.5 GN/YE

0.5

RD

/YE

IF34

68

67

10A

IG1

IF33

66

65

10A

HazardWarningLampSwitch

Flasher Relay

5

4

1

32

8

6P25 7P25 P25 P25 P25

P25P25

2

1

P27

P27

3P27

P25

L

N

R

1212

13

13

A B

11

11P30

P30

P30

Combination Switch

TurnLampSwitch


G105

G106

EF01

80A

M201 2014.01


M4206005

2.0

BK

2.0

BK

0.5

BK

0.5

GN

/YE

0.5

GN

/YE

0.5

GN

/YE

0.5

GN

/YE0.

5 G

N/Y

E

0.3

GN

/YE

0.5

GN

/RD

0.5

GN

/RD

0.5

GN

/RD

0.5

GN

/RD

0.5

GN

/RD

0.3

GN

/RD

A

G103

1.25

BK

G201


Cluster

Refer to 4.2.10Body Control

System


Cluster

Refer to 4.2.10Body Control

System

FrontLeftTurnLamp2 P16

1 P16RearLeftCombinationLamp1 S10

3 S10

14 X04

2.0

BK0.

5 BK

B

G105

1.25

BK

G202

FrontRightTurnLamp

RearRightCombinationLamp2 P06

1 P06

1 S08

3 S08

13 X04

4.2.6-9

M201 2014.01


• Operating circuit analysis of front left turn lamp is as follows:

Current from battery positive→Main fuse box (main fuse EF01)→ I/P fuse box (ignition switch 1 fuseIF01) → Ignition switch connector P31-terminal 3 → Ignition switch IG1 contact → Ignition switchconnector P31-terminal 2 → I/P fuse box (turn lamp fuse IF34) → Hazard warning lamp switchconnector P25-terminal 6 → Hazard warning lamp switch (normal close contact) → Hazard warninglamp switch connector P25-terminal 8 → Flasher relay connector P27-terminal 2 → Flasher relay(closing contact) → Flasher relay connector P27-terminal 1 → Combination switch connector P30-terminal 12→Combination switch (turn lamp switch L)→Combination switch connector P30-terminal13 → Front left turn lamp connector P16-terminal 1 → Front left turn lamp → Front left turn lampconnector P16-terminal 2 → Grounding G103

• Operating circuit analysis of rear left turn lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (ignition switch 1 fuseIF01) → Ignition switch connector P31-terminal 3 → Ignition switch IG1 contact → Ignition switchconnector P31-terminal 2 → I/P fuse box (turn lamp fuse IF34) → Hazard warning lamp switchconnector P25-terminal 6 → Hazard warning lamp switch (normal close contact) → Hazard warninglamp switch connector P25-terminal 8 → Flasher relay connector P27-terminal 2 → Flasher relay(closing contact) → Flasher relay connector P27-terminal 1 → Combination switch connector P30-terminal 12 → Combination switch (turn lamp switch L) → Combination switch connector P30-terminal13 → Connector X04-terminal 14 → Rear left combination lamp connector S10-terminal 3 → Rear leftcombination lamp → Rear left combination lamp connector S10-terminal 1 → Grounding G201

• Operating circuit analysis of front right turn lamp is as follows:

Current from battery positive→Main fuse box (main fuse EF01)→ I/P fuse box (ignition switch 1 fuseIF01) → Ignition switch connector P31-terminal 3 → Ignition switch IG1 contact → Ignition switchconnector P31-terminal 2 → I/P fuse box (turn lamp fuse IF34) → Hazard warning lamp switchconnector P25-terminal 6 → Hazard warning lamp switch (normal close contact) → Hazard warninglamp switch connector P25-terminal 8 → Flasher relay connector P27-terminal 2 → Flasher relay(closing contact) → Flasher relay connector P27-terminal 1 → Combination switch connector P30-terminal 12→Combination switch (turn lamp switch R)→Combination switch connector P30-terminal11 → Front right turn lamp connector P06-terminal 1 → Front right turn lamp → Front right turn lampconnector P06-terminal 2 → Grounding 105

• Operating circuit analysis of rear right turn lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (ignition switch 1 fuseIF01) → Ignition switch connector P31-terminal 3 → Ignition switch IG1 contact → Ignition switchconnector P31-terminal 2 → I/P fuse box (turn lamp fuse IF34) → Hazard warning lamp switchconnector P25-terminal 6 → Hazard warning lamp switch (normal close contact) → Hazard warninglamp switch connector P25-terminal 8 → Flasher relay connector P27-terminal 2 → Flasher relay(closing contact) → Flasher relay connector P27-terminal 1 → Combination switch connector P30-terminal 12 → Combination switch (turn lamp switch L) → Combination switch connector P30-terminal11 → Connector X04-terminal 13 → Rear right combination lamp connector S08-terminal 3 → Rearright combination lamp → Rear right combination lamp connector S08-terminal 1 → Grounding G202

M201 2014.01


• Operating circuit analysis of front left turn lamp (hazard warning lamp) is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (warning lamp switchfuse IF21) → Hazard warning lamp switch connector P25-terminal 7 → Hazard warning lamp switch(closing contact)→Hazard warning lamp switch connector P25-terminal 8→Flasher relay connectorP27-terminal 2→Flasher relay (closing contact)→Flasher relay connector P27-terminal 1→Hazardwarning lamp switch connector P25-terminal 1 → Hazard warning lamp switch (closing contact) →

Hazard warning lamp switch connector P25-terminal 3 → Front left turn lamp connector P16-terminal1 → Front left turn lamp → Front left turn lamp connector P16-terminal 2 → Grounding G103

• Operating circuit analysis of rear left turn lamp (hazard warning lamp) is as follows:


Hazard warning lamp switch connector P25-terminal 3 → Connector X04-terminal 14 → Rear leftcombination lamp connector S10-terminal 3 → Rear left combination lamp → Rear left combinationlamp connector S10-terminal 1 → Grounding G201

• Operating circuit analysis of front right turn lamp (hazard warning lamp) is as follows:


Hazard warning lamp switch connector P25-terminal 2 → Front right turn lamp connector P06-terminal 1→Front right turn lamp→Front right turn lamp connector P06-terminal 2→Grounding G105

• Operating circuit analysis of rear right turn lamp (hazard warning lamp) is as follows:


Hazard warning lamp switch connector P25-terminal 2 → Connector X04-terminal 13 → Rear rightcombination lamp connector S08-terminal 3→Rear right combination lamp→Rear right combinationlamp connector S08-terminal 1 → Grounding G202

4.2.6-11

M201 2014.01


Position Lamp and License Plate Lamp

Main Fuse Box P01

8.0

WH

+B

2

1

EF01

80A

2.0

BK0.

5 BK

G103

2.0

BK0.

5 BK

G105

IF16

10A

0.85

BK

0.85

BK

2.0

BK

0.5

BK

0.5

BK0.

5 R

D/Y

E

0.5 RD/YE

I/P Fuse Box P40

CombinationSwitch

FrontRightPositionLamp

FrontLeftPositionLamp

LicensePlateLamp(Right)

LicensePlateLamp(Left)

RearRightPositionLamp

RearleftpositionLamp

0.5 RD/YE

0.5

RD

/YE

1 1

2 2

2.0

BK1.

25 B

K

3

2

3

2

1.25

BK


Turn Lamp Signal

Refer to 4.1.1Heating, Ventilation and

Air Conditioning



Refer to 4.2.2Instrument Cluster

8.0

WH 0.

5 YE

/RD

0.5

RD

/YE

0.5 RD/YE

0.5

RD

/YE

0.5

RD

/YE

0.5 RD/YE

0.5

RD

/YE

0.5

RD

/YE

0.5

RD

/YE

0.5

RD

/YE

0.5

RD

/YE

0.5

RD

/YE

8.0

WH

31

32

4 4

2X0

4

6

8

OFF

855

1 1

1.25

BK

G202 G201G201

4

P30

P30

P08

P08

S10

S10

S08

S08

D11

D11

D10

D10

P14

P14

X06

X06

PositionLamp

M4206006

M201 2014.01


• Operating circuit analysis of rear left position lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (background lampfuse IF16) → Combination switch connector P30-terminal 5 → Combination switch (position lampcontact) → Combination switch connector P30-terminal 8 → Connector X04-terminal 2 → Rear leftposition lamp connector S10-terminal 4→Rear left position lamp→Rear left position lamp connectorS10-terminal 1 → Grounding G201

• Operating circuit analysis of rear right position lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (background lampfuse IF16) → Combination switch connector P30-terminal 5 → Combination switch (position lampcontact) → Combination switch connector P30-terminal 8 → Connector X04-terminal 2 → Rear rightposition lamp connector S08-terminal 4 → Rear right position lamp → Rear right position lampconnector S08-terminal 1 → Grounding G202

• Operating circuit analysis of front left position lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (background lampfuse IF16) → Combination switch connector P30-terminal 5 → Combination switch (position lampcontact) → Combination switch connector P30-terminal 8 → Front left position lamp connector P14-terminal 2→Front left position lamp→Front left position lamp connector P14-terminal 3→GroundingG103

• Operating circuit analysis of front right position lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (background lampfuse IF16) → Combination switch connector P30-terminal 5 → Combination switch (position lampcontact) → Combination switch connector P30-terminal 8 → Front right position lamp connector P08-terminal 2 → Front right position lamp → Front right position lamp connector P08-terminal 3 →

Grounding G105

• Operating circuit analysis of left license plate lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (background lampfuse IF16) → Combination switch connector P30-terminal 5 → Combination switch (position lampcontact) → Combination switch connector P30-terminal 8 → Connector X04-terminal 2 → ConnectorX06-terminal 4 → Left license plate lamp connector D11-terminal 1 → Left license plate lamp → Leftlicense plate lamp connector D11-terminal 2 → Connector X06-terminal 6 → Grounding G201

• Operating circuit analysis of right license plate lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (background lampfuse IF16) → Combination switch connector P30-terminal 5 → Combination switch (position lampcontact) → Combination switch connector P30-terminal 8 → Connector X04-terminal 2 → ConnectorX06-terminal 4 → Right license plate lamp connector D10-terminal 1 → Right license plate lamp →

Right license plate lamp connector D10-terminal 2 → Connector X06-terminal 6 → Grounding G201

4.2.6-13

M201 2014.01


Fog Lamp

Main Fuse Box P01

+B

2

10.

5 BK

G201

IF16

10A

8.0

WH

8.0

WH

0.5

YE/R

D

0.5 RD/YE

1.25

LG

/BK

0.5

LG/R

D

0.5

GY

0.5

GY

0.5

GY

0.5

BK1.

25 B

K

8.0

WH

31

32

IF14

15A

29

30

2 3

PositionLamp

Front FogLamp

Rear FogLamp

OFF

88

5 11

325

CombinationSwitch

I/P Fuse Box P40

Rear LeftFog Lamp

Rear RightFog Lamp

Front LeftFog Lamp

Front RightFog Lamp



0.5

GY

0.5

GY

0.5

GY

11 X04

1

2

1

2

G202

1.25

BK

2.0

BK

1

2

G103

1.25

BK

2.0

BK

1

2

G106

0.5

BK3.

0 BK

1.25

LG

1.25

LG

1.25

LG

G103

72

70

73

74

P30 P30 P30

P30

S11 S09

S09

P18

P18

P05

P05S11

EF01

80A

IR06

P30

M4206007

M201 2014.01


• Operating circuit analysis of front left fog lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (fog lamp fuse IF14)→ Front fog lamp relay-terminal 73 → Front fog lamp relay (closing contact) → Front fog lamp relay-terminal 74→Front left fog lamp connector P18-terminal 1→Front left fog lamp→Front left fog lampconnector P18-terminal 2 → Grounding G103

• Operating circuit analysis of front right fog lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (fog lamp fuse IF14)→ Front fog lamp relay-terminal 73 → Front fog lamp relay (closing contact) → Front fog lamp relay-terminal 74 → Front right fog lamp connector P05-terminal 1 → Front right fog lamp → Front right foglamp connector P05-terminal 2 → Grounding G106

Front fog lamp is controlled by the combination switch (fog lamp switch) through front fog lamp relay.

• Operating circuit analysis of rear left fog lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (background lampfuse IF16) → Combination switch connector P30-terminal 5 → Combination switch (position lampcontact) → Combination switch connector P30-terminal 8 → Combination switch connector P30-terminal 1 → Combination switch (rear fog lamp contact) → Combination switch connector P30-terminal 2 → Connector X04-terminal 11 → Rear left fog lamp connector S11-terminal 1 → Rear leftfog lamp → Rear left fog lamp connector S11-terminal 2 → Grounding G201

• Operating circuit analysis of rear right fog lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (background lampfuse IF16) → Combination switch connector P30-terminal 5 → Combination switch (position lampcontact) → Combination switch connector P30-terminal 8 → Combination switch connector P30-terminal 1 → Combination switch (rear fog lamp contact) → Combination switch connector P30-terminal 2→Connector X04-terminal 11→Rear right fog lamp connector S09-terminal 1→Rear rightfog lamp → Rear right fog lamp connector S09-terminal 2 → Grounding G202

4.2.6-15

M201 2014.01


Backup Lamp

3.0

YE/B

K

Refer to 4.2.2InstrumentCluster

0.5

YE/B

N

IF33

66

65

10A

IG1IF

34

86

85

10A

0.5

YE/B

N 0.5

YE/B

N

0.5 YE/BN

3 X04

0.5

RD

0.5

RD

0.5

RD

0.5

RD

Backup LampSwitch

2 S15

1 S15

1 X06

LeftBackupLamp

RightBackupLamp

0.5

B0.

85 B

2.0

B

G201

2 D12

1 D12

0.5

B0.

85 B

2 D09

1 D09

6 X06

I/P Fuse Box P40

M4206008

M201 2014.01


• Operating circuit analysis of left backup lamp is as follows:

Current from battery positive→Main fuse box (main fuse EF01)→ I/P fuse box (ignition switch 1 fuseIF01) → Ignition switch connector P31-terminal 3 → Ignition switch IG1 contact → Ignition switchconnector P31-terminal 2 → I/P fuse box (backup lamp & vehicle speed sensor fuse IF33) →

Connector X04-terminal 3 → Backup lamp switch connector S15-terminal 1 → Backup lamp switch(closing contact) → Backup lamp switch connector S15-terminal 2 → Connector X06-terminal 1 →

Left backup lamp connector D12-terminal 2 → Left backup lamp → Left backup lamp connector D12-terminal 1 → Connector X06-terminal 6 → Grounding G201

• Operating circuit analysis of right backup lamp is as follows:

Current from battery positive→Main fuse box (main fuse EF01)→ I/P fuse box (ignition switch 1 fuseIF01) → Ignition switch connector P31-terminal 3 → Ignition switch IG1 contact → Ignition switchconnector P31-terminal 2 → I/P fuse box (backup lamp & vehicle speed sensor fuse IF33) →

Connector X04-terminal 3 → Backup lamp switch connector S15-terminal 1 → Backup lamp switch(closing contact) → Backup lamp switch connector S15-terminal 2 → Connector X06-terminal 1 →

Right backup lamp connector D09-terminal 2 → Right backup lamp → Right backup lamp connectorD09-terminal 1 → Connector X06-terminal 6 → Grounding G201

4.2.6-17

M201 2014.01


Interior Lamp

Main Fuse Box P01

+B

2

1

0.5

WH

2 L02

IF07

10A

8.0

WH

8.0

WH

8.0

WH

0.5

WH

0.5

WH

0.5

WH

0.5

WH

0.5

WH

0.5

BK

0.5

BK/R

D0.

3 BK

/RD

0.3

BK/R

D0.

5 BK

/RD

0.5

BK/R

D

0.5

BK/R

D

0.5

BK/R

D

0.5

BK/R

D

0.5 BK/RD0.3 BK/RD

0.5

BK/R

D

2.0

BK2.

0 BK

2.0

BK0.

5 BK

13

14

I/P Fuse Box P40

Rea

ding

Lam

p

Fron

t Roo

f Lam

p

1 X03

4 X03

2 L01

OFF ONDoor OFF ONDoor

1L01 3L02

G106

3 L01 1 L02

2 X03

8 X04

Front Left DoorSignal Lamp Switch

Front Right DoorSignal Lamp Switch

1 S06

Rear Right DoorSignal Lamp Switch

1 S03

Rear Left DoorSignal Lamp Switch

1 S131 S02

EF01

80A




Cluster


Refer to 4.2.10 Body Control System

M4206009

M201 2014.01


• Operating circuit analysis of front roof lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (roof lamp fuse IF07)→ Connector X03-terminal 1 → Front roof lamp connector L01-terminal 2 → Front roof lamp → Frontroof lamp connector L01-terminal 1 → Connector X03-terminal 4 → Grounding G106

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (roof lamp fuse IF07)→ Connector X03-terminal 1 → Front roof lamp connector L01-terminal 2 → Front roof lamp → Frontroof lamp connector L01-terminal 3→Connector X03-terminal 2→Connector X04-terminal 8 →Frontleft door signal switch connector S06-terminal 1 → Front left door signal switch → Body grounding

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (roof lamp fuse IF07)→ Connector X03-terminal 1 → Front roof lamp connector L01-terminal 2 → Front roof lamp → Frontroof lamp connector L01-terminal 3→Connector X03-terminal 2→Connector X04-terminal 8 →Frontright door signal switch connector S02-terminal 1 → Front right door signal switch → Body grounding

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (roof lamp fuse IF07)→ Connector X03-terminal 1 → Front roof lamp connector L01-terminal 2 → Front roof lamp → Frontroof lamp connector L01-terminal 3→Connector X03-terminal 2→Connector X04-terminal 8→Rearleft door signal switch connector S13-terminal 1 → Rear left door signal switch → Body grounding

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (roof lamp fuse IF07)→ Connector X03-terminal 1 → Front roof lamp connector L01-terminal 2 → Front roof lamp → Frontroof lamp connector L01-terminal 3→Connector X03-terminal 2→Connector X04-terminal 8→Rearright door signal switch connector S03-terminal 1 → Rear right door signal switch → Body grounding

• Operating circuit analysis of reading lamp is as follows:

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (roof lamp fuse IF07)→ Connector X03-terminal 1 → Reading lamp connector L02-terminal 2 → Reading lamp → Readinglamp connector L02-terminal 3 → Connector X03-terminal 4 → Grounding G106

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (roof lamp fuse IF07)→ Connector X03-terminal 1 → Reading lamp connector L02-terminal 2 → Reading lamp → Readinglamp connector L02-terminal 1→Connector X03-terminal 2→Connector X04-terminal 8 →Front leftdoor signal switch connector S06-terminal 1 → Front left door signal switch → Body grounding

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (roof lamp fuse IF07)→ Connector X03-terminal 1 → Reading lamp connector L02-terminal 2 → Reading lamp → Readinglamp connector L02-terminal 1 → Connector X03-terminal 2 → Connector X04-terminal 8 → Frontright door signal switch connector S02-terminal 1 → Front right door signal switch → Body grounding

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (roof lamp fuse IF07)→ Connector X03-terminal 1 → Reading lamp connector L02-terminal 2 → Reading lamp → Readinglamp connector L02-terminal 1 → Connector X03-terminal 2 → Connector X04-terminal 8 → Rear leftdoor signal switch connector S13-terminal 1 → Rear left door signal switch → Body grounding

Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (roof lamp fuse IF07)→ Connector X03-terminal 1 → Reading lamp connector L02-terminal 2 → Reading lamp → Readinglamp connector L02-terminal 1 → Connector X03-terminal 2 → Connector X04-terminal 8 → Rear leftdoor signal switch connector S03-terminal 1 → Rear right door signal switch → Body grounding

4.2.6-19

M201 2014.01


Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

M201 2014.01




4 3 2 1

1 2 3 4

X03

1 2 3 4 5 67 8 9 10

11 12 13 14 15 16

17 18 19 2021 22 23 24 25 26

12345678910

11121314151617181920

212223242526

X04

4.2.6-21

M201 2014.01


Chassis Wiring Harness to Back Door Wiring Harness Back Door Wiring Harness to Chassis Wiring Harness

Alternator Connector Front Right Fog Lamp

Right Turn Lamp Right Low Beam Regulator Motor

1 2

3 4 5 6

1

3456

2

X06

123

P03

12

P05

12

P06

3 2 1

P07

M201 2014.01


Right Headlamp Left Headlamp

Left Low Beam Regulator Motor Left Turn Lamp

Front Left Fog Lamp Brake Lamp Switch

123

456

P08

123

456

P14

3 2 1

P15

12

P16

12

P18

1

2

P20

4.2.6-23

M201 2014.01


Diode A Diode B

Hazard Warning Lamp Switch Flasher Relay

Combination Switch (Lighting) Lighting Power Control Switch

1

2

P23

1

2

P24

123

478 56

P25

1

23

P27

561213 7891011

1234

P30

12

3456

P41

M201 2014.01


Right Backup Lamp Right License Plate Lamp

Left License Plate Lamp Left Backup Lamp

High Mounted Stop Lamp Front Right Door Signal Lamp Switch

2 1

D09

1

2

D10

1

2

D11

2 1

D12

2 1

D13

1

S02

4.2.6-25

M201 2014.01


Rear Left Door Signal Lamp Switch Front Left Door Signal Lamp Switch

Rear Right Combination Lamp Rear Right Fog Lamp

Rear Left Combination Lamp Rear left Fog Lamp

1

S03

1

S06

1 2 3 4

S08

2 1

S09

1 2 3 4

S10

2 1

S11

M201 2014.01


Rear Left Door Signal Lamp Switch Backup Lamp

ECM

Front Interior Lamp Rear Interior Lamp

1

S13

21

S15

7 8

5 6

3 4

1 2

51 52 53 54 55 56 57 58 59 60 61 62 63 64

37 38 39 40 41 42 43 44 45 46 47 48 49 50

23 24 25 26 27 28 29 30 31 32 33 34 35 36

9 10 11 12 13 14 15 16 17 18 19 20 21 22

E18

1 2 3

L01

31 2

L02

4.2.7-1

M201 2014.01

4.2.7-1Wiper

Front Wiper

5 P334 P332 P33 7 P33 6 P33

IF25

20A

50

49

1.25

YE/

GN

1.25

YE/

GN

1.25

YE/

GN

1.25

BU

/WH

1.25

BU

0.5 YE/BU

1.25

BU

1.25

BU

/RD

1.25

BU

/RD

0.5

GN

/YE

1.25

BK

2.0

BK

2 P17

M

1 P11 2 P11

M

4P1

1

LOW HI

IF26

10A

IG2

52

51

3.0

BK/B

U

1 P17

G103

I/P Fuse Box P40

Wiper Intermittent Control Module

Wiper Combination Switch

FrontWasherMotor

FrontWiperMotor

T TPOFFON

B+ +2 +1 +S INT1 INT2 WF EWB1PMISTOFFINT

LOWHI

3 P33

3 P11

M4207001

4.2.7 Wiper

M201 2014.01

4.2.7-2 4.2.7-2Wiper

• Operating circuit analysis of front wiper motor is as follows:

Intermittent level：Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (ignition switch 2 fuse IF02) → Ignition switch connector P31-terminal 4 → Ignition switch IG2 contact→ Ignition switch connector P31-terminal 5→ I/P fuse box (wiper& washer fuse IF25)→Combinationswitch connector P33-terminal 3 → Combination switch (wiper intermittent control module) →

Combination switch (intermittent level closing contact)→Combination switch connector P33-terminal4 → Front wiper motor connector P11-terminal 1 → Front wiper motor (low speed coil) → Front wipermotor grounding

Low speed level：Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (ignition switch 2 fuse IF02) → Ignition switch connector P31-terminal 4 → Ignition switch IG2 contact→ Ignition switch connector P31-terminal 5→ I/P fuse box (wiper& washer fuse IF25)→Combinationswitch connector P33-terminal 3 → Combination switch (intermittent level closing contact) →

Combination switch connector P33-terminal 4→Front wiper motor connector P11-terminal 1→Frontwiper motor (low speed coil) → Front wiper motor grounding

High speed level：Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (ignition switch 2 fuse IF02) → Ignition switch connector P31-terminal 4 → Ignition switch IG2 contact→ Ignition switch connector P31-terminal 5→ I/P fuse box (wiper& washer fuse IF25)→Combinationswitch connector P33-terminal 3 → Combination switch (high speed level closing contact) →

Combination switch connector P33-terminal 2→Front wiper motor connector P11-terminal 2→Frontwiper motor (high speed coil) → Front wiper motor grounding

• Operating circuit analysis of front washer motor is as follows:

Current from battery positive→Main fuse box (main fuse EF01)→ I/P fuse box (ignition switch 2 fuseIF02) → Ignition switch connector P31-terminal 4 → Ignition switch IG2 contact → Ignition switchconnector P31-terminal 5→ I/P fuse box (wiper& washer fuse IF25)→Front washer motor connectorP17-terminal 2→Front washer motor→Front washer motor connector P17-terminal 1→Combinationswitch connector P33-terminal 7→Combination switch (washer level closing contact)→Combinationswitch connector P33-terminal 6 → Grounding G103

4.2.7-3

M201 2014.01

4.2.7-3Wiper

I/P Fuse Box

Front Wiper Motor Front Washer Motor

Combination Switch (Wiper)

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

12

34

P11

1

2

P17

110 23456789

P33

4.2.8-1

M201 2014.01

4.2.8-1Central Door Lock

Central Door Lock

+B

2

18.0

WH

EF01

80A

Main Fuse Box P01

1.25

WH

/BK

0.85

WH

0.85

WH0.

5 W

H/Y

E

0.5

YE0.

5 YE

0.5

WH

/YE

0.85

WH

0.85

WH

0.85

WH

0.85 WH

0.85

BU

0.85

WH

IF40

80

79

15A

ACC

1.25

BU

8.0

WH

1.25

RD

/WH

0.5

BK/R

D

0.5

GN

/RD

0.5

GN

/YE

1.25

BK

2.0

BK

8.0

WH

I/P Fuse Box P40

Central Lock Controller

FastenerSwitch

1 P29 5 26

2 6

3 41

P29

81112 P29 9P29

D01

D01

1S07

IF22

20A

43

44

710

M M

12 X01

1 X01 5 X01

11 X01

9 X0121 X04

9 X02

24 X04

10 X02

2S07

0.85

BU

0.85

BU

0.85

BU

0.5 BK2.0 BK

2.0

BK3.

0 BK

0.85 BU

0.85

BU

Front LeftDoorFastener

Front RightDoorFastener

Rear LeftDoorfastener

Rear RightDoorfastener

2D08

M

1D08

0.85

BU

1S04

M

2S04

D01

D01D01

P29P29

G103

G105

P29 P29 P29 P29


Roof Lamp


Turn Signal Lamp

M4208001

4.2.8 Central Door Lock

M201 2014.01

4.2.8-2 4.2.8-2Central Door Lock

• Operating circuit analysis of front left door fastener is as follows:

Unlock：Current from central lock controller → Central lock controller connector P29-terminal 8 →

Connector X01-terminal 12 → Front left door fastener connector D01-terminal 4 → Front left doorfastener (motor) → Front left door fastener connector D01-terminal 6 → Connector X01-terminal 11→ Central lock controller connector P29-terminal 9 → Central lock controller

When unlocking, current from central lock controller→Central lock controller connector P29-terminal11→Connector X01-terminal 5 → Front left door fastener connector D01-terminal 3 → Front left doorfastener (switch) → Front left door fastener connector D01-terminal 2 → Connector X01-terminal 9 →

Grounding G103

Central lock controller determines the fastener position based on low level signal.

Lock：Current from central lock controller → Central lock controller connector P29-terminal 9 →

Connector X01-terminal 11 → Front left door fastener connector D01-terminal 6 → Front left doorfastener→Front left door fastener connector D01-terminal 4→Connector X01-terminal 12→Centrallock controller connector P29-terminal 8 → Central lock controller

When locking, current from central lock controller → Central lock controller connector P29-terminal12→Connector X01-terminal 1→Front left door fastener connector D01-terminal 1→Front left doorfastener (switch) → Front left door fastener connector D01-terminal 2 → Connector X01-terminal 9 →

Grounding G103

Central lock controller determines the fastener position based on low level signal.

• Operating circuit analysis of front right door fastener is as follows:


Connector X02-terminal 10 → Front right door fastener connector D08-terminal 2 → Front right doorfastener (motor) → Front right door fastener connector D08-terminal 1 → Connector X02-terminal 9→ Central lock controller connector P29-terminal 9 → Central lock controller


Connector X02-terminal 9 → Front right door fastener connector D08-terminal 1 → Front right doorfastener (motor) → Front right door fastener connector D08-terminal 2 → Connector X02-terminal 10→ Central lock controller connector P29-terminal 8 → Central lock controller

• Operating circuit analysis of rear left door fastener is as follows:


Connector X04-terminal 24 → Rear left door fastener connector S07-terminal 1 → Rear left doorfastener (motor) → Rear left door fastener connector S07-terminal 2 → Connector X04-terminal 21→ Central lock controller connector P29-terminal 9 → Central lock controller


Connector X04-terminal 21 → Rear left door fastener connector S07-terminal 2 → Rear left doorfastener (motor) → Rear left door fastener connector S07-terminal 1 → Connector X04-terminal 24→ Central lock controller connector P29-terminal 8 → Central lock controller

4.2.8-3

M201 2014.01


• Operating circuit analysis of rear right door fastener is as follows:


Connector X04-terminal 24 → Rear right door fastener connector S04-terminal 1 → Rear right doorfastener (motor) → Rear right door fastener connector S04-terminal 2 → Connector X04-terminal 21→ Central lock controller connector P29-terminal 9 → Central lock controller


Connector X04-terminal 21 → Rear right door fastener connector S04-terminal 2 → Rear right doorfastener (motor) → Rear right door fastener connector S04-terminal 1 → Connector X04-terminal 24→ Central lock controller connector P29-terminal 8 → Central lock controller

M201 2014.01


Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

4.2.8-5

M201 2014.01




1 2 4 53

6 7 11 128 9 10

34

11 10 812

5

7 69

2 1

X01

1 2 4 53

6 7 11 128 9 10

34

11 10 812

5

7 69

2 1

X02

M201 2014.01



Central Lock Controller Front Left Door Fastener

Front Right Door Fastener Rear Right Door Fastener

1 2 3 4 5 67 8 9 10

11 12 13 14 15 16

17 18 19 2021 22 23 24 25 26

12345678910

11121314151617181920

212223242526

X04

12345

12 11 10 9 8 7 6

P29

5

1 2 3

4 6

D01

2 1

D08

2 1

S04

4.2.8-7

M201 2014.01


Rear Left Door Fastener

2 1

S07

4.2.9-1

M201 2014.01

4.2.9-1Power Window

Power Window

2.0

BK

2.0

BK2.

0 BK

3.0

BK

G105

1D

02

IC

UP

UP

PU

DU DD

PD

DOWN

DOWNU

U

RLD

D

P/W P SW

P/W D SW W/L SW

LOCK

UNLOCK

RelayFr

ont R

ight

Doo

r Pow

er W

indo

w S

witc

h

Front LeftDoor Power

Window Motor

Front RightDoor Power

Window Motor

Fron

t Lef

t Doo

r Pow

er W

indo

w S

witc

h

DOWNAUTO

6 D02

2D

023

D02

6 D07 7 D07 2 D07

3.0

BK/B

U

2.0

BU/Y

E2.

0 BU

/YE

2.0

GN

/WH

2.0

GN

/WH

2.0

GN

/WH

IF28

56

55

20A

IG2

IF26

52

51

20A

I/P Fuse Box P402.

0 W

H/B

N2.

0 W

H/B

N

2.0 RD/WH

2.0

RD

2.0

RD

2.0 BK

2.0

GN

2.0

GN

2.0

RD

/WH

2.0

RD

/WH

2.0

RD

/YE2.

0 R

D/Y

E

2.0 RD/YE

IF27

54

53

30A

8D07

4 D07

3 X026 X01

X0110

X027

X018

X017

8

6

X02

9 X01

X02

5 X02

7 D02

MM

3 D071 D07

2 D06 1 D06

4

2

D02

D03

8 D02

1 D03

G103

M4209001

4.2.9 Power Window

M201 2014.01

4.2.9-2 4.2.9-2Power Window

• Operating circuit analysis of front left door power window motor is as follows:

Up: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (ignition switch 2fuse IF02) → Ignition switch connector P31-terminal 4 → Ignition switch IG2 contact → Ignition switchconnector P31-terminal 5 → I/P fuse box (front left door power window fuse IF27) → Connector X01-terminal 6 → Front left door power window switch connector D02-terminal 7 → Front left door powerwindow switch (relay contact)→Front left door power window switch connector D02-terminal 4→Frontleft door power window motor connector D03-terminal 2 → Front left door power window motor → Frontleft door power window motor connector D03-terminal 1 → Front left door power window switchconnector D02-terminal 8 → Front left door power window switch (relay normal close contact) → Frontleft door power window switch connector D02-terminal 1 → Connector X01-terminal 9 → GroundingG103

Down: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (ignition switch2 fuse IF02) → Ignition switch connector P31-terminal 4 → Ignition switch IG2 contact → Ignition switchconnector P31-terminal 5 → I/P fuse box (front left door power window fuse IF27) → Connector X01-terminal 6 → Front left door power window switch connector D02-terminal 7 → Front left door powerwindow switch (relay contact)→Front left door power window switch connector D02-terminal 8→Frontleft door power window motor connector D03-terminal 1 → Front left door power window motor → Frontleft door power window motor connector D03-terminal 2 → Front left door power window switchconnector D02-terminal 4 → Front left door power window switch (relay normal close contact) → Frontleft door power window switch connector D02-terminal 1 → Connector X01-terminal 9 → GroundingG103

• Operating circuit analysis of front right door power window motor is as follows:

Up: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (ignition switch 2fuse IF02) → Ignition switch connector P31-terminal 4 → Ignition switch IG2 contact → Ignition switchconnector P31-terminal 5 → I/P fuse box (front right door power window fuse IF28) → Connector X02-terminal 3 → Front right door power window switch connector D07-terminal 8 → Front right door powerwindow switch (relay contact)→Front right door power window switch connector D07-terminal 1→Frontright door power window motor connector D06-terminal 2 → Front right door power window motor →

Front right door power window motor connector D06-terminal 1→Front right door power window switchconnector D07-terminal 3→Front right door power window switch (relay normal close contact) →Frontright door power window switch connector D07-terminal 4 → Connector X02-terminal 7 → GroundingG105

Down: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (ignition switch2 fuse IF02) → Ignition switch connector P31-terminal 4 → Ignition switch IG2 contact → Ignition switchconnector P31-terminal 5 → I/P fuse box (front right door power window fuse IF28) → Connector X02-terminal 3 → Front right door power window switch connector D07-terminal 8 → Front right door powerwindow switch (relay contact)→Front right door power window switch connector D07-terminal 3→Frontright door power window motor connector D06-terminal 1 → Front right door power window motor →

Front right door power window motor connector D06-terminal 2→Front right door power window switchconnector D07-terminal 1→Front right door power window switch (relay normal close contact) →Frontright door power window switch connector D07-terminal 4 → Connector X02-terminal 7 → GroundingG105

4.2.9-3

M201 2014.01

4.2.9-3Power Window

I/P Fuse Box


1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

1 2 4 53

6 7 11 128 9 10

34

11 10 812

5

7 69

2 1

X01

M201 2014.01

4.2.9-4 4.2.9-4Power Window


Front Left Door Power Window Switch Front Left Door Power Window Motor

Front Right Door Power Window Motor Front Right Door Power Window Switch

1 2 4 53

6 7 11 128 9 10

34

11 10 812

5

7 69

2 1

X02

57

23

6

1

8 4

D02

2 1

D03

2 1

D06

57

23

6

1

8 4

D07

4.2.10-1

M201 2014.01

4.2.10-1Body Control System

Body Control System

+B

2

18.0

WH

EF01

80A

Main Fuse Box P01

1.25

WH

/BK

IF40

80

79

15A

ACC

1.25

BU

8.0

WH

1.25

RD

/WH

1.25

BK

2.0

BK

8.0

WH

I/P Fuse Box P40


1 P29 5

2

P29

IF22

20A

43

44

G105

P29

M4210001

4.2.10 Body Control System

M201 2014.01

4.2.10-2 4.2.10-2Body Control System

• Operating circuit analysis of central lock controller is as follows:

Constant power supply: Current from battery positive → Main fuse box (main fuse EF01) → I/P fusebox (central lock controller fuse IF22) → Central lock controller connector P29-terminal 1 → Centrallock controller → Central lock controller connector P29-terminal 2 → Grounding G105

ACC energizing power supply: Current from battery positive → Main fuse box (main fuse EF01) → I/P fuse box (ignition switch 2 fuse IF02) → Ignition switch connector P31-terminal 4 → Ignition switchACC contact → Ignition switch connector P31-terminal 1 → I/P fuse box (cigarette lighter & radio fuseIF40) → Central lock controller connector P29-terminal 5 → Central lock controller → Central lockcontroller connector P29-terminal 2 → Grounding G105

4.2.10-3

M201 2014.01

4.2.10-3Body Control System

Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

M201 2014.01

4.2.10-4 4.2.10-4Body Control System


12345

12 11 10 9 8 7 6

P29

4.2.11-1

M201 2014.01

4.2.11-1On-board Network System

DLC (Data Link Connector)

+B

2

18.0

WH

EF01

80A

Main Fuse Box P018.

0 W

H

0.5

PK/B

U0.

5 PK

/BU

0.5

LG/W

H0.

5 LG

/WH

0.5 PK/BU 0.5 PK/BU

2.0

BK

0.5

BK

0.5

BK

8.0

WH

I/P Fuse Box P40

8 P35

16E1

8

12

IF11

10A

21

22

ECM

P35 13

G106

P35

DLC

12X0

5

12X05

15 E18

15 P35

M4211001

4.2.11 On-board Network System

M201 2014.01

4.2.11-2 4.2.11-2On-board Network System

Main Fuse Box

I/P Fuse Box

1

2

EF01

P01

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

4.2.11-3

M201 2014.01

4.2.11-3On-board Network System


DLC

ECM

1 7 8 9 10 411 12 13 14

2 15 16 17 18 5

19 20 21 223 23 24 25 26 6

1

2

3

7

11

15

19

23

8

12

16

20

24

9

13

17

21

25

10

14

18

22

26

4

5

6

X05

12345678

910111213141516

P35

7 8

5 6

3 4

1 2

51 52 53 54 55 56 57 58 59 60 61 62 63 64

37 38 39 40 41 42 43 44 45 46 47 48 49 50

23 24 25 26 27 28 29 30 31 32 33 34 35 36

9 10 11 12 13 14 15 16 17 18 19 20 21 22

E18

M201 2014.01

6.1.1-1 6.1.1-1Fuse and Relay

Main Fuse Box

Main Fuse Box Fuse

1

2

EF01

P01

Code Application Rated Current (A) DescriptionEF01 Main Fuse 80A -

6.1.1 Fuses and Relays

6.1.1-2

M201 2014.01

6.1.1-2Fuse and Relay

I/P Fuse Box

I/P Fuse Box Relay

1

2

15

16

13

14

3

4

5

6

7

8

9

10

11

12

45

4647

5448

50

5152

5953

55

5657

6458

60

6162

6963

65

6667

68

70

71

7273

75

7677

78 8382

80

81 8687

88

90

9192

93

49

74 79 84 89 94

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

IF01IF07

IF24






P40

Code Application DescriptionIR01 A/C Compressor Relay -

IR02 Heater Relay -

IR03 Radiator Fan Relay -

IR04 Condenser Fan Relay -

IR05 Main Relay -

IR06 Front Fog Lamp Relay -

IR07 Rear Defroster Relay -

IR08 Fuel Pump Relay -

IR09 Horn Relay -

IR10 - -

M201 2014.01

6.1.1-3 6.1.1-3Fuse and Relay

I/P Fuse Box Fuse

Code Application Rated Current (A) DescriptionIF01 Ignition Switch 1 30A -

IF02 Ignition Switch 2 40A -

IF03 Radiator Fan 30A -

IF04 Condenser Fan 20A -

IF05 EPS 30A -

IF06 - - -

IF07 Roof Lamp 10A -

IF08 Left Headlamp &Left Aiming Motor 15A -

IF09 Right Headlamp &Right Aiming Motor 15A -

IF10 Brake Lamp 10A -

IF11 ECU Diagnostor 10A -

IF12 Horn 15A -

IF13 - - -

IF14 Fog Lamp 15A -

IF15 Main Relay 15A -

IF16 Background Lamp 10A -

IF17 Heater & Overhead Evaporator 30A -

IF18 Compressor 10A -

IF19 Fuel Pump 15A -

IF20 Rear Defroster 25A -

IF21 Warning Switch 15A -

IF22 Central Controller 25A -

IF23 - - -

IF24 - - -

IF25 Wiper & Washer 20A -

IF26 Blower & Rear Defroster 10A -

IF27 Left Power Window 30A -

IF28 Right Power Window 30A -

IF29 - - -

IF30 Oxygen Sensor 15A -

IF31 - - -

IF32 - - -

IF33 Backup Lamp &Vehicle Speed Sensor 10A -

IF34 Turn Lamp 10A -

6.1.1-4

M201 2014.01

6.1.1-4Fuse and Relay

IF35 Instrument Cluster 10A -

IF36 Alternator 15A -

IF37 ECU 10A -

IF38 EPS 10A -

IF39 - - -

IF40 Cigarette Lighter & Radio 15A -

Code Application Rated Current (A) Description

M201 2014.01

6.1.2-1 6.1.2-1Power Supply Distribution

I/P Power Supply Distribution 1

M6102001

1.25 LG/BK

72 70

73 74IR06

2.0 GN/WH

52 50

53 54IR02

I/P Fuse Box P40

1 30A

IF01

2

0.85 RD0.85 RD

0.5 RD

87 85

88 89IR09

Main Fuse Box P018.

0 W

H8.

0 W

H

8.0

WH

+B

2

1 3 40A

IF02

4

13 10A

IF07

14

15 15A

IF08

16

17 15A

IF09

18

19 10A

IF10

20

21 10A

IF11

22

23 15A

IF12

24

27 15A

IF14

28

31 10A

IF16

32

33 30A

IF17

34

41 15A

IF21

42

43 20A

IF22

44

EF01

80A

6.1.2 Power Supply Distribution

6.1.2-2

M201 2014.01

6.1.2-2Power Supply Distribution


M6102002

37 15A

IF19

38

2.0 WH/YE

0.5 WH/YET

I/P Fuse Box P40Main Fuse Box P01

8.0

WH

8.0

WH

8.0

WH

+B

2

1

59 15A

IF30

60

2.0 RD/BU

0.5 RD/BU

0.5 RD/BU

0.5 RD/BU

0.5 RD/BU

57 55

58 59IR035 30A

IF03

6

2.0 BU/WH

62 60

63 64IR047 20A

IF04

8

0.85 OG/BK

47 45

48 49IR0135 10A

IF18

36

1.25 RD/YE

82 80

83 84IR08

67 65

68 69IR0529 15A

IF15

302.0 RD/BU 2.0 RD/BU

EF01

80A

M201 2014.01

6.1.2-3 6.1.2-3Power Supply Distribution


M6102003

I/P Fuse Box P40

I/P Fuse Box P40

Main Fuse Box P01

8.0

WH

8.0

WH

8.0

WH

3.0

WH

/GN

3.0

RD

/BK

1.25 BU

+B

2

1

1 30A

IF01

2

3.0 BK/BU

3.0 YE/BK

3 40A

IF02

4

3 P31

2 P31 5 P31 1 P31

4 P31

IG1

IG2ST ST

ACC

ACC

LOC

K

LOC

K OFF

OFF

L1 L2

Ignition Switch

79 15A

IF40

80

49 20A

IF25

50

31 10A

IF26

32

33 30A

IF27

34

35 20A

IF28

36

65 10A

IF33

66

67 10A

IF34

68

69 10A

IF35

70

71 15A

IF36

72

73 10A

IF37

74

EF01

80A

M201 2014.01

6.1.3-1 6.1.3-1Fuse Details

EF01 IF01 IF02 IF07 IF08 IF09 IF10 IF11 IF12 IR09

M6103001

I/P Fuse Box P40Starting Motor Switch

Alternator Positive

Ignition Switch

Instrument Cluster

Radio

Front Interior Lamp

Left Headlamp

Right Headlamp

Brake Lamp Switch

Engine ECM

DLC

Electrical Horn

Horn Switch

+B

1

1 30A

IF01

2

80A

EF01

2

3.0 WH/GN

8.0 WH

15.0 RD 15.0 RD

1P0

41

S16

8P2

1

1P3

4

23 15A

IF12

24

3P3

1

3 40A

IF02

43.0 RD/BK

13 10A

IF07

140.5 WH 0.5 WH

0.5 WH

0.5 WH 0.5 WH

4P3

12

L01

15 15A

IF08

161.25WH/BU

1X0

312

X05

5P1

4

17 15A

IF09

181.25WH/RD

5P0

819 10A

IF10

200.5GN/YE

1P2

0

21 10A

IF11

220.5PK/BU

0.85RD

0.5RD 0.5YE

0.5PK/BU

16E1

88

P35

0.85 WH/GN

2P1

21

P32

87 85

88 89IR09

6.1.3 Fuse Details

6.1.3-2

M201 2014.01

6.1.3-2Fuse Details

EF01 IF14 IF16 IF17 IF21 IF22 IR02 IR06

M6103002

31 10A

IF16

320.5 YE/RD

I/P Fuse Box P40

+B1 80A

EF01

215.0 RD

52 50

53 5433

41

30A

IF17

34 IR022.0 GN/WH

0.5BK/WH

0.85RD/BK

2.0 RD/GN

1P2

8Heater Motor

7P2

5

Hazard WarningLamp Switch

2.0 RD/GN 2.0 RD/GN

1L0

3

Overhead Evaporator Motor

72 70

73 7427 15A

IF14

28 IR06

0.5 BK

0.5 LG/RD

1.25 LG

1.25 LG

0.3 LG

1.25 LG/BK

1P1

8

Front Left Fog Lamp

Front Right Fog Lamp

Instrument Cluster

Combination Switch (Lighting)

1P0

520

P21

G103

0.5 BKG103

IF26

3P3

05

P30

3X0

3

15A

IF21

42

431.25RD/WH

1P2

9


20A

IF22

44

M201 2014.01


EF01 IF03 IF04 IF15 IF18 IF19 IR01 IR03 IR04 IR05 IR08

M6103003

I/P Fuse Box P40

2.0 RD/BU

2.0 RD/BU 2.0 BU/RD

0.5 BK/WH 0.5 BK/WH

0.5 RD/BU 1P1

0

Radiator Fan

52E1

8

Engine ECM

+B1 80A

EF01

215.0 RD

67 65

68 6929 15A

IF15

30 IR05

0.5 WH/YE

2.0 WH/YE

57 55

58 595 30A

IF03

6 IR03

19X0

5

2.0 BU/WH 2.0 RD/BK

0.5 BK/RD 0.5 BK/RD

0.5 RD/BU 1P1

3

Condenser Fan

62E1

8

Engine ECM

Engine ECM

Engine ECM

62 60

63 647 20A

IF04

8 IR04

23X0

5

1.25 BU/WH

0.85 OG/BK 0.85 OG

0.5 BK/YE 0.5 BK/RD

0.5 RD/BU 1P0

2

Compressor

61E1

847 45

48 4935 10A

IF18

36 IR01

24X0

5

16X0

4 1.25 BU/WH 1.25 BU/WH

3X0

71.25 RD/YE

0.5 YE/RD 0.5 YE/RD

0.5 RD/BU 4S0

1

Fuel Pump

60E1

8

82 80

83 8437 15A

IF19

38 IR08

25X0

5

6.1.3-4

M201 2014.01

6.1.3-4Fuse Details

EF01 IF15 IF30 IR05

M6103004

I/P Fuse Box P40

Engine ECM

Engine ECM

8E1

851

E18

+B1 80A

EF01

215.0 RD

67 65

68 6929 15A

IF15

30 59 15A

IF30

60IR051.25 RD/BU

2.0 RD/BU 1.5 RD/BU

1.5 RD/BU

1.5 RD/BU

1.5 RD/BU

1.25 RD/GN1.25 RD/GN

0.85 RD/GN1.25 RD/GN

0.5 WH/YE

2.0 WH/YE

3S1

4

Rear Oxygen Sensor

4E0

4

Front Oxygen Sensor

1E0

8

Ignition Coil 1

Ignition Coil 2

Ignition Coil 3

Ignition Coil 4

1E0

71

E05

1E0

3

0.5 BN/WH 0.5BN/WH

32E1

8

15X0

5

6X0

46

X05

1X0

5

1.0 RD/BU

1E0

9

Fuel Injector 1

Fuel Injector 2

Fuel Injector 3

Fuel Injector 4

1.0 RD/BU

1E0

6

1.0 RD/BU

1E0

4

1.0 RD/BU

1E0

2

0.85 RD/BU

1E1

3


1.25 RD/BU

0.5 RD/BU

M201 2014.01


IF25 IF26 IF27 IF28

M6103005

I/P Fuse Box P40

1.25 YE/GN 1.25 YE/GN

1.25 YE/GN

0.5 YE/GN

IG23.0 BK/BU

ST22.0 BK/YE

31 10A

IF26

320.5 BK/WH

49 20A

IF25

50

A/C Controller

4P2

6


3P3

3

Starting Motor

1S1

7

Front Wiper Motor

3P1

1

33 30A

IF27

IF28

342.0 WH/BN 2.0 WH/BN

Front Left Door PowerWindow Switch

7D

02

35 20A 362.0 BU/YE 2.0 BU/YE

Front Right Door PowerWindow Switch

8D

07

Front Washer Motor

2P1

70.5 YE/GN

Heater Relay52

P40

6X0

11

X04

3X0

2

6.1.3-6

M201 2014.01

6.1.3-6Fuse Details


M6103006

I/P Fuse Box P40

0.5 YE/BN 0.5 YE/BN

0.5 YE/BN

IG13.0 YE/BK

67 10A

IF34

680.85 YE

65 10A

IF33

66

Hazard Warning Lamp Switch

6P2

5

69 10A

IF35

700.5 GN/BK

Backup Lamp Switch

1S1

5

71 15A

IF36

721.25 BK/BU

Alternator Connector

2P0

3

73 10A

IF37

740.5 BU 0.5 BU

Engine ECM

17E1

8

Vehicle Speed Sensor

1S1

2

11X0

53

X04

Instrument Cluster

7P2

1

1.25 WH/BK 1.25 WH/BK

1.25 WH/BK

0.85 WH/BK

ACC1.25 BU

79 15A

IF40

80Cigarette Lighter Positive

1P3

7


5P2

9

Radio

5P3

4

M201 2014.01

6.1.4-1 6.1.4-1Grounding Distribution

G103 G104

M6104001

Front Left Door PowerWindow Switch

Front LeftDoor Fastener Front Fog Lamp Relay

Heater Relay

CombinationSwitch (Lighting) Left Turn Lamp

Left Headlamp

Condenser Fan Front Left fog Lamp

CombinationSwitch (Wiper)

18 P08

9 X01

Vehicle Speed SensorFuel PumpInstrument Cluster Brake Fluid Level Switch

10 X04

2 X07

3.0

BK

0.5

BK

0.5

BK

2.0

BK

0.5

BK

2 P1370 P40

2.0

BK

0.5

BK

1.25

BK

1.25

BK

0.5

BK

7 P30

6 P333

2 P18 2 P16

P14

2.0

BK2.

0 BK

0.5

BK

1 D02

2 D01

50 P40 3 P41

3.0

BK

0.5

BK

0.5

BK

9 P21

0.3

BK

1 P19

0.5

BK0.

5 BK

0.5

BK/Y

E0.

5 BK

/YE

2 S121 S01

G104

G103

Lamp PowerControl Switch

6.1.4 Grounding Distribution

6.1.4-2

M201 2014.01

6.1.4-2Grounding Distribution

G105 G106

M6104002

7 X02

Radio

4 X03

2.0

BK

0.5

BK

1.25

BK

2.0

BK

0.85

BK

0.85

BK

2 P103 P09

0.5

BK

0.5

BK

3 P27

3

2 P06

P08

2.0

BK2.

0 BK

4 D07 2 P29 1 P12

G105

2.0

BK

2.0

BK

1.25

BK

0.5

BK

0.85

BK

10 P26

0.5

BK

1.25

BK

4 P34

12

2 P05

P35 13 P35

2.0

BK2.

0 BK

2 L023 L03

1 P36

4 P25

G106

0.5

BK

0.5

BK

1 L01

Front Right Door PowerWindow Switch

TristatePressure Switch Flasher Relay Radiator Fan Right Turn Lamp

Rear Interior Lamp

Front Right Fog LampFront Interior Lamp

A/C Controller DLCOverhead

Evaporator Motor

CigaretteLighter Negative

Hazard WarningLamp Switch

Central Lock Controller Right Headlamp Electrical Horn

M201 2014.01

6.1.4-3 6.1.4-3Grounding Distribution

G201 G202

M6104003

Rear RightCombination Lamp

Rear Left Fog Lamp

4 X07 6 X06

2.0

BK

1.25

BK

0.5

BK

0.5

BK

2D11

1 S10

0.5

BK

2

2 2 S11

D10

1.25

BK

1.25

BK

0.85

BK

0.5

BK

2 S01

1 D13 1 D09

G201

0.5

BK

1 S05

0.5

BK

2 S09

1.25

BK

1.25

BK

1 S08

G202

0.5

BK1 D12

0.5

BK

High MountedStop Lamp

Seat Belt Switch Rear Right Fog Lamp

Right LicensePlate Lamp

Left LicensePlate Lamp

Right Backup Lamp

Fuel Pump Left Backup Lamp

Rear LeftCombination Lamp

6.1.4-4

M201 2014.01

6.1.4-4Grounding Distribution

G301 G302 G303

M6104004

2.0B

K2.

0BK

5 E18

G301

1.0

BK

1.0

BK

1.0

BK

1.0

BK

2 E08 2 E03

1.5

BK

2 E07 2 E05

G303

0.5B

K0.

5BK

43 E18

G302

48

0.5

BK

E18

Engine ECM

Ignition Coil 1 Ignition Coil 2 Ignition Coil 3 Ignition Coil 4

Engine ECM

M201 2014.01

6.1.5-1 6.1.5-1Wiring Harness Connector Location View

Connector Joining wiring Harness and wiring Harness (X--)

X03X01 X02

M6105001

6.1.5 Wiring Harness Connector Location View

6.1.5-2

M201 2014.01

6.1.5-2Wiring Harness Connector Location View

X04 X05

M6105002

M201 2014.01


X07 X06

M6105003

6.1.5-4

M201 2014.01


X08

M6105014

M201 2014.01


Connector Joining Wiring Harness and Wiring Harness (X) Chart

A Connector Name B Connector Name DefinitionI/P Wiring Harness to Front Left Door Wiring Harness

Front Left Door Wiring Harness to I/P Wiring Harness X01

I/P Wiring Harness to Front Right Door Wiring Harness

Front Right Door Wiring Harness to I/P Wiring Harness X02

I/P Wiring Harness to Roof Wiring Harness Roof Wiring Harness to I/P Wiring Harness X03

I/P Wiring Harness to Chassis Wiring Harness Chassis Wiring Harness to I/P Wiring Harness X04

I/P Wiring Harness to Engine Wiring Harness Engine Wiring Harness to I/P Wiring Harness X05

Chassis Wiring Harness to Back Door Wiring Harness

Back Door Wiring Harness to Chassis Wiring Harness X06

Chassis Wiring Harness to Fuel Pump Wiring Harness

Fuel Pump Wiring Harness to Chassis Wiring Harness X07


Overhead Evaporator Wiring Harness to Roof Wiring Harness X08

6.1.5-6

M201 2014.01


Engine Wiring Harness Connector (E--)

E19

E06 E07 E08 E09 E10E05E04E03E02E01

E12 E17E16E15E14E13E11 E18M6105004

M201 2014.01


Engine Wiring Harness Connector (E) Chart

Connector Name DefinitionFront Oxygen Sensor E01

Fuel Injector 4 E02

Ignition Coil 4 E03

Fuel Injector 3 E04

Ignition Coil 3 E05

Fuel Injector 2 E06

Ignition Coil 2 E07

Ignition Coil 1 E08

Fuel Injector 1 E09

Engine Oil Pressure Sensor E10

Coolant Temperature Sensor E11

Knock Sensor E12

Carbon Canister Solenoid E13

Stepper Motor E14

Air Intake Pressure/Temperature Sensor E15

Throttle Position Sensor E16

Crankshaft Position Sensor E17

Engine ECM E18

Transmission Grounding E19

6.1.5-8

M201 2014.01


I/P Wiring Harness Connector (P--)

P01 P04P03P02

M6105005

M201 2014.01


P17P16P15P14P13P11P09P08P07P06

P18

P19

P12P10P05

M6105006

6.1.5-10

M201 2014.01


P35P34P33P32P31P30 P39P38P37P36

P21P20P41 P29P28P27P26P25

P22 P40 P24 P23

M6105007

M201 2014.01


I/P Wiring Harness Connector (P) Chart

Connector Name DefinitionMain Fuse P01

Compressor P02

Alternator Connector P03

Alternator Positive P04

Front Right Fog Lamp P05

Right Turn Lamp P06

Right Low Beam Regulator Motor P07

Right Headlamp P08

Tristate Pressure Switch P09

Radiator Fan P10

Front Wiper Motor P11

Electrical Horn P12

Condenser Fan P13

Left Headlamp P14

Left Low Beam Regulator Motor P15

Left Turn Lamp P16

Front Washer Motor P17

Front Left Fog Lamp P18

Brake Fluid Level Switch P19

Brake Lamp Switch P20

Instrument Cluster P21

Diode P22

Diode A P23

Diode B P24

Hazard Warning Lamp Switch P25

A/C Controller P26

Flasher Relay P27

Heater Motor P28

Central Lock Controller P29

Combination Switch (Lighting) P30

Ignition Switch P31

Horn Switch P32

Combination Switch (Wiper) P33

Radio P34

DLC P35

Cigarette Lighter Negative P36

Cigarette Lighter Positive P37

6.1.5-12

M201 2014.01


Governor Resistor P38

Evaporator Thermistor P39

Fuse Box P40

Lighting Power Control Switch P41

Connector Name Definition

M201 2014.01


Floor Wiring Harness Connector (S--)

S10S09S08S07S06S05S04S03S02

S19 S18 S17 S16 P41S15 P41S14 S13 S12 S11

S01

M6105008

6.1.5-14

M201 2014.01


S20

M6105013

M201 2014.01


Floor Wiring Harness Connector (S) Chart

Connector Name DefinitionFuel Pump S01

Front Right Door Signal Lamp Switch S02

Rear Right Door Signal Lamp Switch S03

Rear Right Door Fastener S04

Seat Belt Switch S05

Front Left Door Signal Lamp Switch S06

Rear Left Door Fastener S07

Rear Right Combination Lamp S08

Rear Right Fog Lamp S09

Rear Left Combination Lamp S10

Rear Left Fog Lamp S11

Vehicle Speed Sensor S12

Rear Left Door Signal Lamp Switch S13

Rear Oxygen Sensor S14

Backup Lamp Switch S15

Starting Motor Switch S16

Starting Motor S17

Parking Brake Switch S18

Battery Positive S19

Battery Negative S20

6.1.5-16

M201 2014.01


Door Wiring Harness Connector (D--)

D04D03D02D01

M6105009

M201 2014.01


D08D07D06D05

M6105010

6.1.5-18

M201 2014.01


D12D11D10D09 D13

M6105011

M201 2014.01


Door Wiring Harness Connector (D) Chart

Connector Name DefinitionFront Left Door Fastener D01

Front Left Door Power Window Switch D02

Front Left Door Power Window Motor D03

Front Left Speaker D04

Front Right Speaker D05

Front Right Door Power Window Motor D06

Front Right Door Power Window Switch D07

Front Right Door Fastener D08

Right Backup Lamp D09

Right License Plate Lamp D10

Left License Plate Lamp D11

Left Backup Lamp D12

High Mounted Stop Lamp D13

6.1.5-20

M201 2014.01


Roof Wiring Harness Connector (L--)

Roof Wiring Harness Connector (L) Chart

Connector Name DefinitionFront Interior Lamp L01

Rear Interior Lamp L02

Overhead Evaporator Blower L03

Blower Resistor L04

Blower Switch L05

L03 L02L01 L04 L05

M6105012

M201 2014.01

6.1.6-1 6.1.6-1Grounding Location View

GND1

GND1

M6106001

6.1.6 Grounding Location View

6.1.6-2

M201 2014.01

6.1.6-2Grounding Location View

GND191 G301 G302 G303

G302

G303 G301GND191

M6106002

M201 2014.01

6.1.6-3 6.1.6-3Grounding Location View

G103 G104 D105 G106

G103G105

G104G106

M6106004

6.1.6-4

M201 2014.01

6.1.6-4Grounding Location View

G201 G202

G201

G202

M6106003

M201 2014.01

6.1.7-1 6.1.7-1Wiring Harness Connector Terminal View

Connector Joining Wiring Harness and Wiring Harness (X--)

X01 Wiring Harness Connector Pin Definition


1 2 4 53

6 7 11 128 9 10

34

11 10 812

5

7 69

2 1

X01

Pin No. Wire Diameter/Color Function1 - -

2 0.5 RD Front Left Speaker Positive

3 0.5 RD/BK Front Left Speaker Negative

4 0.5 WH/YE Locking Switch Signal A

5 0.5 YE Locking Switch Signal B

6 2.0 WH/BN Power Window Main Switch Power Supply

7 2.0 RD/YE Front Right Door Control Power Supply Output

8 2.0 GN/WH Passenger Side Door Glass Down Control

9 2.0 BK Grounding

10 2.0 RD/WH Passenger Side Door Glass Up Control

11 0.85 BU Front Left Door Lock Motor Locking Power Supply

12 0.85 WH Front Left Door Lock Motor Unlocking Power Supply

6.1.7 Wiring Harness Connector Terminal View

6.1.7-2

M201 2014.01

6.1.7-2Wiring Harness Connector Terminal View



1 2 4 53

6 7 11 128 9 10

34

11 10 812

5

7 69

2 1

X02

Pin No. Wire Diameter/Color Function1 0.5 BU/RD Front Right Speaker Positive

2 0.5 BU/BK Front Right Speaker Negative

3 2.0 BU/YE Front Right Power Window Switch Power Supply

4 - -

5 2.0 RD/YE Front Right Door Control Power Supply

6 2.0 GN/WH Passenger Side Glass Down Signal Controlled by Driver Side

7 2.0 BK Grounding

8 2.0 RD/WH Passenger Side Glass Up Signal Controlled by Driver Side

9 0.85 BU Front Right Door Lock Motor Locking Power Supply

10 0.85 WH Front Right Door Lock Motor Unlocking Power Supply

11 - -

12 - -

M201 2014.01




4 3 2 1

1 2 3 4

X03

Pin No. Wire Diameter/Color Function1 0.5 WH Interior Roof Lamp Power Supply

2 0.3 BK/RD Interior Roof Lamp DR Position Signal Output

3 2.0 RD/GN Overhead Evaporator Motor Power Supply

4 2.0 BK Grounding

6.1.7-4

M201 2014.01




1 2 3 4 5 67 8 9 10

11 12 13 14 15 16

17 18 19 2021 22 23 24 25 26

12345678910

11121314151617181920

212223242526

X04

Pin No. Wire Diameter/Color Function1 2.0 BK/YE Starting Switch Power Supply

2 0.5 RD/YE Rear Position Lamp & Rear License Plate Lamp Power Supply

3 0.5 YE/BN Vehicle Speed Sensor & Backup Lamp Switch Power Supply

4 0.5 GN/WH Rear Brake Lamp Power Supply

5 0.3 RD/BK Parking Brake Switch Signal

6 1.25 RD/GN Rear Oxygen Sensor Heating Power Supply

7 0.5 YE Rear Oxygen Sensor Signal

8 0.5 BK/RD Door Signal Lamp Switch Signal

9 0.3 GY/BK Seat Belt Switch Power Supply

10 0.5 BK Fuel Level Sensor & Vehicle Speed Sensor Grounding

11 0.5 GY Rear Fog Lamp Power Supply

12 - -

13 0.5 GN/YE Rear Right Turn Lamp Power Supply

14 0.5 GN/RD Rear Left Turn Lamp Power Supply

15 - -

16 1.25 BU/WH Fuel Pump Power Supply

17 0.5 WH/RD Rear Oxygen Sensor Heating Signal

18 0.3 YE/RD Fuel Level Sensor Power Supply

19 0.5 YE/GN Rear Oxygen Sensor Grounding

20 0.3 GN Vehicle Speed Sensor Signal

M201 2014.01


21 0.85 BU Rear Door Lock Motor Locking Power Supply

22 - -

23 - -

24 0.85 WH Rear Door Lock Motor Unlocking Power Supply

25 - -

26 - -

Pin No. Wire Diameter/Color Function

6.1.7-6

M201 2014.01




1 7 8 9 10 411 12 13 14

2 15 16 17 18 5

19 20 21 223 23 24 25 26 6

1

2

3

7

11

15

19

23

8

12

16

20

24

9

13

17

21

25

10

14

18

22

26

4

5

6

X05

Pin No. Wire Diameter/Color Function1 2.0 RD/BU Main Relay Power Supply

2 0.3 YE/BK Engine Oil Pressure Signal

3 0.3 YE/WH Coolant Temperature Signal

4 - -

5 - -

6 1.25 RD/GN Front Oxygen Sensor Heating Signal

7 0.5 LG/RD Blower Switch Signal

8 0.5 BU/BK A/C Medium Pressure Switch Signal

9 0.3 WH/BU Engine Speed Signal

10 0.5 WH/RD Rear Oxygen Sensor Heating

11 0.5 BU Ignition Switch Power Supply

12 0.5 PK/BU Constant Power Supply

13 0.5 LG/WH Diagnosis K Line

14 0.5 LG/BK A/C Temperature Sensor

15 0.5 BN/WH Main Relay

16 0.5 YE Rear Oxygen Sensor

17 0.5 RD/YE Headlamp Switch Signal

18 0.3 VT/YE MIL Lamp

19 0.5 BK/WH Radiator Fan Relay

20 0.5 PK/BK A/C Switch Signal

21 0.5 BU/RD Sensor Grounding 2

22 0.5 YE/GN Sensor Grounding 1

M201 2014.01


Pin No. Wire Diameter/Color Function23 0.5 BK/RD A/C Condenser Fan Relay

24 0.5 BK/YE A/C Compressor Relay

25 0.5 YE/RD Fuel Pump Relay

26 0.3 YE/GN Vehicle Speed Signal

6.1.7-8

M201 2014.01



Chassis Wiring Harness to Back Door Wiring Harness Back Door Wiring Harness to Chassis Wiring Harness

1 2

3 4 5 6

1

3456

2

X06

Pin No. Wire Diameter/Color Function1 0.5 RD Backup Lamp Power Supply

2 - -

3 0.5 GN/WH High Mounted Stop Lamp Power Supply

4 0.5 RD/YE Rear License Plate Lamp Power Supply

5 - -

6 0.5 BK Grounding

M201 2014.01



Fuel Pump Wiring Harness to Chassis Wiring Harness Chassis Wiring Harness to Fuel Pump Wiring Harness

13

24

1

2

3

4

X07

Pin No. Wire Diameter/Color Function1 0.3 YE/RD Fuel Level Sensor Power Supply

2 0.5 BK/YE Fuel Level Sensor Grounding


4 1.25 BK Fuel Pump Grounding

6.1.7-10

M201 2014.01




Overhead Evaporator Wiring Harness to Roof Wiring Harness

1

2

1

2

X08

Pin No. Wire Diameter/Color Function1 2.0 BK/RD Overhead Evaporator Motor Power Supply

2 2.0 BK Grounding

M201 2014.01


Engine Wiring Harness Connector (E--)

E01 Wiring Harness Connector Pin Definition


Front Oxygen Sensor

1

2

3

4

E01

Pin No. Wire Diameter/Color Function1 0.5 BK/OG Front Oxygen Sensor Signal

2 0.5 YE/GN Front Oxygen Sensor Grounding

3 0.85 YE/WH Front Oxygen Sensor Heating Signal

4 0.85 RD/GN Front Oxygen Sensor Heating Power Supply

Fuel Injector 4

1 2

E02


1 1.0 RD/BU Fuel Injector 4 Power Supply (+B, Main Relay Control)

2 0.5 WH/BK Fuel Injector 4 Signal

6.1.7-12

M201 2014.01




Ignition Coil 4

1 2 3

E03

Pin No. Wire Diameter/Color Function1 1.5 RD/BU Ignition Coil 4 (+B, Main Relay Control)

2 1.0 BK Ignition Coil 4 Grounding

3 1.5 BK/RD Ignition Coil 4 Signal

Fuel Injector 3

1 2

E04



2 0.5 WH/GN Fuel Injector 3 Signal

M201 2014.01




Ignition Coil 3

1 2 3

E05



3 1.5 BK/BU Ignition Coil 3 Signal

Fuel Injector 2

1 2

E06



2 0.5 WH/YE Fuel Injector 2 Signal

6.1.7-14

M201 2014.01




Ignition Coil 2

1 2 3

E07



3 1.5 BK/VT Ignition Coil 2 Signal

Ignition Coil 1

1 2 3

E08



3 1.5 BK/YE Ignition Coil 1 Signal

M201 2014.01




Fuel Injector 1

1 2

E09



2 0.5 WH/BN Fuel Injector 1 Signal

Engine Oil Pressure Sensor

1

E10

Pin No. Wire Diameter/Color Function1 0.5 YE/BK Engine Oil Pressure Switch Power Supply

6.1.7-16

M201 2014.01




Coolant Temperature Sensor

1 2

E11

Pin No. Wire Diameter/Color Function1 0.5 BU/RD Coolant Temperate Sensor Grounding

2 0.5 BN/YE Engine Coolant Temperate Sensor Signal

Knock Sensor

1 2 3

E12

Pin No. Wire Diameter/Color Function1 0.5 RD Knock Sensor A

2 0.5 GN Knock Sensor B

3 0.5 BK Grounding

M201 2014.01




Carbon Canister Control Valve

1 2

E13

Pin No. Wire Diameter/Color Function1 0.85 RD/BU Carbon Canister Control Valve Power Supply

2 0.85 RD/WH Carbon Canister Control Valve Signal

Stepper Motor

4321

E14

Pin No. Wire Diameter/Color Function1 0.5 GY/GN Idle Control Valve Signal A

2 0.5 GY/YE Idle Control Valve Signal B

3 0.5 GY Idle Control Valve Signal C

4 0.5 GY/BK Idle Control Valve Signal D

6.1.7-18

M201 2014.01




Air Intake Pressure/Temperature Sensor

1 2 3 4

E15


1 0.5 BU/RD Air Intake Pressure/Temperature Sensor Internal Grounding

2 0.5 BU/GN Air Intake Temperature Sensor Signal

3 0.5 YE/BK Air Intake Pressure/Temperature Sensor 5 V Power Supply

4 0.5 YE/BN Air Intake Pressure Sensor Signal

Throttle Position Sensor

1 2 3

E16

Pin No. Wire Diameter/Color Function1 0.5 YE/GN Throttle Position Sensor Internal Grounding

2 0.5 BU/BN Throttle Position Sensor 5 V Power Supply

3 0.5 BU/WH Throttle Position Sensor Signal

M201 2014.01





1 2 3

E17

Pin No. Wire Diameter/Color Function1 0.5 YE/BK Crankshaft Position Sensor 5 V Power Supply

2 0.5 BU/WH Crankshaft Position Sensor Signal

3 0.5 BU/RD Crankshaft Position Sensor Grounding

ECM

7 8

5 6

3 4

1 2

51 52 53 54 55 56 57 58 59 60 61 62 63 64

37 38 39 40 41 42 43 44 45 46 47 48 49 50

23 24 25 26 27 28 29 30 31 32 33 34 35 36

9 10 11 12 13 14 15 16 17 18 19 20 21 22

E18

Pin No. Wire Diameter/Color Function1 1.25 BK/RD Ignition Coil for 4th Cylinder

2 0.85 YE/WH Front Oxygen Sensor Heating

3 1.25 BK/YE Ignition Coil for 1st Cylinder

4 0.85 WH Rear Oxygen Sensor Heating

5 2.0 BK Grounding

6.1.7-20

M201 2014.01


Pin No. Wire Diameter/Color Function6 1.25 BK/VT Ignition Coil for 2nd Cylinder

7 1.25 BK/BU Ignition Coil for 3rd Cylinder

8 1.25 RD/BU Non-constant Power Supply

9 0.5 WH/BU Engine Speed Output

10 0.5 BU/BK A/C Medium Pressure Switch

11 - -

12 0.5 LG/RD Blower Switch

13 0.5 LG/BK A/C Temperature Sensor

14 - -

15 0.5 LG/WH 0.5 LG/WH

16 0.5 PK/BU Constant Power Supply

17 0.5 BU Ignition Switch

18 0.5 BU/BN 5V Power Supply 2

19 0.5 YE/BK 5V Power Supply 1

20 0.5 VT/YE MIL Lamp

21 0.5 GY/YE Stepper Motor Phase B

22 0.5 GY/GN Stepper Motor Phase A

23 - -

24 0.5 RD/YE Headlamp Switch

25 0.5 BU/GN Air Intake Temperature Sensor

26 0.5 BU/WH Throttle Position Sensor

27 - -

28 - -

29 0.5 YE Rear Oxygen Sensor

30 0.5 RD Knock Sensor Side A

31 0.5 GN Knock Sensor Side B

32 0.5 BN/WH Main Relay

33 - -

34 - -

35 0.5 GY Stepper Motor Phase C

36 0.5 GY/BK Stepper Motor Phase D

37 0.5 RD/WH Carbon Canister Valve

38 - -

39 0.5 YE/GN Sensor Grounding 1

40 0.5 BU/RD Sensor Grounding 2

41 0.5 BN/YE Engine Coolant Temperature Sensor

42 - -

M201 2014.01



Pin No. Wire Diameter/Color Function43 0.5 BK Electrical Grounding 1

44 0.5 PK/BK A/C Switch

45 0.5 BK/OG Front Oxygen Sensor

46 - -

47 0.5 BU/WH Engine Speed Sensor

48 0.5 BK Power Grounding 1

49 0.5 WH/GN Fuel Injector 2 (3rd Cylinder)

50 0.5 WH/BN Fuel Injector 1 (1st Cylinder)

51 0.5 RD/BU Non-constant Power Supply

52 0.5 BK/WH Radiator Fan Relay

53 - -

54 - -

55 - -

56 0.5 YE/WH Coolant Temperature Output

57 0.5 YE/GN Vehicle Speed Signal

58 - -

59 0.5 YE/BN Air Intake Pressure Sensor

60 0.5 YE/RD Fuel Pump Relay

61 0.5 BK/YE A/C Compressor Relay

62 0.5 BK/RD A/C Condenser Fan Relay

63 0.5 WH/YE Fuel Injector 4 (2nd Cylinder)

64 0.5 WH/BK Fuel Injector 3 (4th Cylinder)

Transmission Grounding

E19

1

Pin No. Wire Diameter/Color Function 1 15.0 BK Engine & Transmission Grounding

6.1.7-22

M201 2014.01


I/P Wiring Harness Connector (P--)

P02 Wiring Harness Connector Pin Definition


Compressor

1

P02

Pin No. Wire Diameter/Color Function1 0.85 OG A/C Compressor Clutch Power Supply

Alternator Connector

123

P03


2 1.25 BK/BU Ignition Switch ON Signal

3 0.3 RD/WH Charging Indicator Signal

M201 2014.01




Alternator Positive

1

P04

Pin No. Wire Diameter/Color Function1 8.0 WH Battery Charging Power Supply Output

Front Right Fog Lamp

12

P05

Pin No. Wire Diameter/Color Function1 1.25 LG Front Right Fog Lamp Power Supply

2 1.25 BK Grounding

6.1.7-24

M201 2014.01




Right Turn Lamp

12

P06

Pin No. Wire Diameter/Color Function1 0.5 GN/YE Right Turn Lamp Power Supply

2 0.5 BK Grounding

Right Low Beam Regulator Motor

3 2 1

P07

Pin No. Wire Diameter/Color Function1 0.5 BK Right Light Regulator Motor Grounding

2 0.5 GN Right Low Beam Lamp Height Signal

3 0.5 WH/RD Right Light Regulator Motor Power Supply

M201 2014.01




Right Headlamp

123

456

P08


2 0.5 RD/YE Front Right Position Lamp Power Supply

3 0.5 BK Front Right Position Lamp Grounding

4 1.25 RD/WH Low Beam Lamp Signal Output

5 1.25 WH/RD Right Headlamp Power Supply Input

6 1.25 RD High Beam Lamp Signal Output

Tristate Pressure Switch

1

243

P09

Pin No. Wire Diameter/Color Function1 0.5 GN/BU A/C Signal Input

2 0.5 PK/WH A/C Signal Output

3 0.5 BK Medium Pressure Signal Grounding

4 0.5 BU/BK Medium Pressure Signal Input

6.1.7-26

M201 2014.01




Radiator Fan

12

P10

Pin No. Wire Diameter/Color Function1 2.0 BU/RD Radiator Fan Motor Power Supply

2 2.0 BK Grounding

Front Wiper Motor

12

34

P11

Pin No. Wire Diameter/Color Function1 1.25 BU Front Wiper Motor Low Speed Level Signal

2 1.25 BU/RD Front Wiper Motor High Speed Level Signal

3 1.25 YE/GN Front Wiper Motor Power Supply (IG2)

4 1.25 BU/WH Front Wiper Motor Intermittent Level Signal

M201 2014.01




Electrical Horn

12

P12

Pin No. Wire Diameter/Color Function1 0.85 BK Grounding

2 0.85 WH/GN Horn Power Supply

Condenser Fan

12

P13

Pin No. Wire Diameter/Color Function1 2.0 RD/BK Condenser Fan Motor Power Supply

2 2.0 BK Grounding

6.1.7-28

M201 2014.01




Left Headlamp

123

456

P14


2 0.5 RD/YE Front Left Position Lamp Power Supply

3 0.5 BK Front Left Position Lamp Grounding

4 1.25 RD/WH Low Beam Lamp Signal Output

5 1.25 WH/BU Left Headlamp Power Supply Input

6 1.25 RD High Beam Lamp Signal Output

Left Low Beam Regulator Motor

3 2 1

P15

Pin No. Wire Diameter/Color Function1 0.5 BK Left Light Regulator Motor Grounding

2 0.5 YE Left Low Beam Lamp Height Signal

3 0.5 WH/BU Left Light Regulator Motor Power Supply

M201 2014.01




Left Turn Lamp

12

P16

Pin No. Wire Diameter/Color Function1 0.5 GN/RD Left Turn Lamp Power Supply

2 0.5 BK Grounding

Front Washer Motor

1

2

P17

Pin No. Wire Diameter/Color Function1 0.5 GN/YE Grounding

2 0.5 YE/BU Front Washer Motor Power Supply

6.1.7-30

M201 2014.01




Front Left Fog Lamp

12

P18

Pin No. Wire Diameter/Color Function1 1.25 LG Front Left Fog Lamp Power Supply

2 1.25 BK Grounding

Brake Fluid Level Switch

12

P19


2 0.3 RD/BK Brake Oil Level Switch Power Supply

M201 2014.01




Brake Lamp Switch

1

2

P20

Pin No. Wire Diameter/Color Function1 0.5 GN/YE Brake Lamp Switch Power Supply

2 0.5 GN/WH Brake Lamp Switch Signal Output

Instrument Cluster

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

26 27 28 29 30 31 3217 18 19 20 21 22 23 24 25

P21

Pin No. Wire Diameter/Color Function1 0.3 GN/YE Right Turn Lamp Signal

2 0.3 GN/RD Left Turn Lamp Signal

3 0.3 RD High Beam Indicator Signal

4 0.3 RD/WH Low Beam Indicator Signal

5 0.3 YE/GN Instrument Cluster Power Supply (IG1)

6 - -

6.1.7-32

M201 2014.01


Pin No. Wire Diameter/Color Function7 0.5 GN/BK Instrument Cluster Power Supply (IG1)

8 0.5 WH Instrument Cluster Power Supply (B+)

9 0.5 BK Instrument Cluster Signal Grounding

10 0.3 YE/RD Fuel Level Sensor Signal

11 0.3 GN Vehicle Speed Signal Input

12 0.3 WH/BU Speed Sensor Signal

13 0.3 YE/WH Coolant Temperature Sensor Signal

14 - -

15 - -

16 - -

17 0.3 RD/YE Background Lamp Power Supply

18 0.5 BK Lighting Grounding

19 0.3 GY Rear Fog Lamp Indication Signal

20 0.3 LG Front Fog Lamp Indication Signal

21 0.3 BK/RD Door Open Indication Signal

22 0.3 GY/BK Seat Belt Unfastened Warning Signal

23 0.3 YE/BK Engine Oil Pressure Signal

24 0.3 WH/RD Battery Charging Indication Signal

25 - -

26 - -

27 0.3 RD/BK Brake Fluid Level & Parking Brake Indication Signal

28 0.3 VT/YE Engine Fault Indication Signal

29 - -

30 - -

31 - -

32 - -

M201 2014.01




Diode

1

2

P22

Pin No. Wire Diameter/Color Function1 0.5 LG/RD A/C Load Signal Output

2 0.5 PK/WH A/C Load Signal

Diode A

1

2

P23

Pin No. Wire Diameter/Color Function1 0.5 RD/YE High Beam ON Signal Input

2 0.5 RD High Beam ON Signal Output

6.1.7-34

M201 2014.01




Diode B

1

2

P24

Pin No. Wire Diameter/Color Function1 0.5 RD/YE Low Beam ON Signal Input

2 0.5 RD/WH Low Beam ON Signal Output

Hazard Warning Lamp Switch

123

478 56

P25

Pin No. Wire Diameter/Color Function1 0.85 YE/GN Hazard Warning Lamp Power Supply Input

2 0.5 GN/YE Right Turn Lamp Power Supply Output

3 0.5 GN/RD Left Turn Lamp Power Supply Output

4 0.5 BK Background Lamp Grounding

5 0.5 RD/YEHazard Warning Lamp & Background Lamp

Power Supply

6 0.85 YE Turn Lamp Power Supply Input (IG1)

7 0.85 RD/BK Turn Lamp Power Supply Input (B+)

8 0.85 GN Turn Lamp Power Supply Output

M201 2014.01




A/C Controller

12345

678910

P26


2 0.5 PK/BK A/C Switch Signal

3 0.5 GN/BU A/C Output

4 0.5 BK/WH A/C Switch Indicator Power Supply


6 2.0 PK/BU 3rd Air Volume

7 2.0 YE 2nd Air Volume

8 2.0 PK 1st Air Volume

9 0.5 PK/WH Air Volume ON Signal

10 2.0 BK Grounding

Flasher Relay

1

23

P27

Pin No. Wire Diameter/Color Function1 0.85 YE/GN Turn Lamp Combination Switch Signal Input

2 0.85 GN Turn Lamp Relay Power Supply

3 0.85 BK Grounding

6.1.7-36

M201 2014.01




Heater Motor

1

2

P28

Pin No. Wire Diameter/Color Function1 2.0 RD/GN Heater Motor Power Supply

2 2.0 PK/BU Heater Motor Signal Output


12345

12 11 10 9 8 7 6

P29

Pin No. Wire Diameter/Color Function1 1.25 RD/WH Central Lock Controller Power Supply (B+)

2 1.25 BK Central Lock Controller Grounding

3 - -

4 - -

5 1.25 WH/BK Central Lock Controller Power Supply (ACC)

6 0.5 GN/YE Right Turn Lamp

7 0.5 GN/RD Left Turn Lamp

8 0.85 WH Door Unlocking Power Supply

9 0.85 BU Door Locking Power Supply

10 0.5 BK/RD Door Signal Switch

M201 2014.01



Pin No. Wire Diameter/Color Function11 0.5 YE Locking Switch Signal A

12 0.5 WH/YE Locking Switch Signal B

Combination Switch (Lighting)

561213 7891011

1234

P30

Pin No. Wire Diameter/Color Function1 0.5 RD/YE Fog Lamp Power Supply

2 0.5 GY Rear Fog Lamp Power Supply Output

3 0.5 LG/RD Front Fog Lamp Switch Signal Output

4 - -

5 0.5 YE/RD Position Lamp & Background Lamp Power Supply Input

6 - -

7 2.0 BK Grounding

8 0.5 RD/YE Position Lamp & Background Lamp Power Supply Output

9 1.25 RD High Beam Signal

10 1.25 RD/WH Low Beam Signal

11 0.5 GN/YE Right Turn Lamp

12 0.5 YE/GN Turn Lamp Power Supply

13 0.5 GN/RD Left Turn Lamp

6.1.7-38

M201 2014.01




Ignition Switch

123

456

P31

Pin No. Wire Diameter/Color Function1 1.25 BU Ignition Switch ACC

2 3.0 YE/BK Ignition Switch IG1

3 3.0 WH/GN Ignition Switch Power Supply 1

4 3.0 RD/BK Ignition Switch Power Supply 2

5 3.0 BK/BU Ignition Switch IG2

6 2.0 BK/YE Ignition Switch ST

Horn Switch

1

P32

Pin No. Wire Diameter/Color Function1 0.5 YE Horn Signal

M201 2014.01





110 23456789

P33


2 1.25 BU/RD Front Wiper Motor High Speed Level Signal Output

3 1.25 YE/GN Wiper Combination Switch Power Supply (IG1)

4 1.25 BU Front Wiper Motor Low Speed Level Signal Output

5 1.25 BU/WH Front Wiper Motor Intermittent Speed Level Signal Output

6 1.25 BK Grounding

7 0.5 GN/YE Front Washer Motor Signal

8 - -

9 - -

10 - -

Radio

123

478 56

P34

Pin No. Wire Diameter/Color Function1 0.5 WH Radio Power Supply (+B)

2 0.5 BU/RD Front Right Speaker Positive

6.1.7-40

M201 2014.01



Pin No. Wire Diameter/Color Function3 0.5 RD Front Left Speaker Positive

4 0.85 BK Radio Grounding

5 0.85 WH/BK Radio Power Supply (ACC)

6 0.5 RD/YE Backup Lamp Power Supply

7 0.5 BU/BK Front Right Speaker Negative

8 0.5 RD/BK Front Left Speaker Negative

DLC

12345678

910111213141516

P35


2 - -

3 - -

4 - -

5 - -

6 - -

7 - -

8 0.5 PK/BU DLC Power Supply

9 - -

10 - -

11 - -

12 0.5 BK Grounding

13 0.5 BK Grounding

14 - -

15 0.5 LG/WH K-line

16 - -

M201 2014.01




Cigarette Lighter Negative

1

P36


Cigarette Lighter Positive

1

P37

Pin No. Wire Diameter/Color Function1 1.25 WH/BK Cigarette Lighter Power Supply

6.1.7-42

M201 2014.01




Governor Resistor

12

34

P38

Pin No. Wire Diameter/Color Function1 2.0 YE Heater Motor Medium Speed Level Output

2 2.0 PK Heater Motor Low Speed Level Output

3 - -

4 2.0 PK/BU Heater Motor High Speed Level Output


12

P39

Pin No. Wire Diameter/Color Function1 0.5 BU/RD Evaporator Thermistor Internal Grounding

2 0.5 LG/BK Evaporator Thermistor Signal

M201 2014.01



Lighting Power Control Switch

12

3456

P41

Pin No. Wire Diameter/Color Function1 0.5 BK Lighting Control Grounding

2 0.5 WH/BU Lighting Control Power Supply

3 0.5 BK Background Lamp Grounding

4 0.5 BN Right Low Beam Lamp Height Signal

5 0.5 YE Left Low Beam Lamp Height Signal


6.1.7-44

M201 2014.01


Floor Wiring Harness Connector (S--)

S01 Wiring Harness Connector Pin Definition


Fuel Pump

1

2

3

4

S01

Pin No. Wire Diameter/Color Function1 0.5 BK/YE Fuel Level Sensor Grounding

2 1.25 BK Fuel Pump Grounding

3 0.5 YE/RD Fuel Level Sensor Power Supply


Front Right Door Signal Lamp Switch

1

S02

Pin No. Wire Diameter/Color Function1 0.5 BK/RD Front Right Door Signal Lamp Switch Signal

M201 2014.01




Rear Right Door Signal Lamp Switch

1

S03

Pin No. Wire Diameter/Color Function1 0.5 BK/RD Rear Right Door Signal Lamp Switch Signal

Rear Right Door Fastener

2 1

S04


1 0.85 WH Rear Right Door Lock Motor Unlocking Power Supply

2 0.85 BU Rear Right Door Lock Motor Locking Power Supply

6.1.7-46

M201 2014.01




Seat Belt Switch

1

2

S05

Pin No. Wire Diameter/Color Function1 0.5 BK Seat Belt Switch Grounding

2 0.5 GY/BK Seat Belt Switch Power Supply

Front Left Door Signal Lamp Switch

1

S06

Pin No. Wire Diameter/Color Function1 0.5 BK/RD Front Left Door Signal Lamp Switch Signal

M201 2014.01




Rear Left Door Fastener

2 1

S07


1 0.85 WH Rear Left Door Lock Motor Unlocking Power Supply

2 0.85 BU Rear Left Door Lock Motor Locking Power Supply

Rear Right Combination Lamp

1 2 3 4

S08


2 0.5 GN/WH Rear Right Brake Lamp Power Lamp

3 0.5 GN/YE Rear Right Turn Lamp Power Supply

4 0.5 RD/YE Rear Right Position Lamp Power Supply

6.1.7-48

M201 2014.01




Rear Right Fog Lamp

2 1

S09

Pin No. Wire Diameter/Color Function1 0.5 GY Rear Right Fog Lamp Power Supply

2 0.5 BK Grounding

Rear Left Combination Lamp

1 2 3 4

S10


2 0.5 GN/WH Rear Left Brake Lamp Power Supply

3 0.5 GN/RD Rear Left Turn Lamp Power Supply

4 0.5 RD/YE Rear Left Position Lamp Power Supply

M201 2014.01




Rear Left Fog Lamp

2 1

S11

Pin No. Wire Diameter/Color Function1 0.5 GY Rear Left Fog Lamp Power Supply

2 0.5 BK Grounding

Vehicle Speed Sensor

1 2 3

S12

Pin No. Wire Diameter/Color Function1 0.5 YE/BN Vehicle Speed Sensor Power Supply

2 0.5 BK Grounding

3 0.5 GN Vehicle Speed Sensor Signal

6.1.7-50

M201 2014.01




Rear Left Door Signal Lamp Switch

1

S13

Pin No. Wire Diameter/Color Function1 0.5 BK/RD Rear Left Door Signal Lamp Switch Signal

Rear Oxygen Sensor

12

34

S14

Pin No. Wire Diameter/Color Function1 0.5 WH/RD Rear Oxygen Sensor Heating Signal

2 0.5 YE Rear Oxygen Sensor Signal

3 1.25 RD/GN Rear Oxygen Sensor Heating Power Supply

4 0.5 YE/GN Rear Oxygen Sensor Grounding

M201 2014.01




Backup Lamp Switch

21

S15

Pin No. Wire Diameter/Color Function1 0.5 YE/BN Backup Lamp Power Supply Input

2 0.5 RD Backup Lamp Power Supply Output

Starting Motor Switch

1

S16

Pin No. Wire Diameter/Color Function1 2.0 BK/YE Starting Motor Switch Power Supply

6.1.7-52

M201 2014.01




Starting Motor

1

S17

Pin No. Wire Diameter/Color Function1 15.0 RD Starting Motor Power Supply

Parking Brake Switch

1

S18

Pin No. Wire Diameter/Color Function1 0.5 RD/BK Parking Brake Switch Signal

M201 2014.01




Battery Positive

1

S19

Pin No. Wire Diameter/Color Function1 15.0 RD Battery Power Supply

Battery Negative

S20

Pin No. Wire Diameter/Color Function1 15.0 BK Battery Grounding

6.1.7-54

M201 2014.01


Door Wiring Harness Connector (D--)

D01 Wiring Harness Connector Pin Definition


Front Left Door Fastener

Pin No. Wire Diameter/Color Function1 0.5 WH/YE Locking Switch Signal A

2 0.5 BK Locking Switch Grounding

3 0.5 YE Locking Switch Signal B

4 0.85 WH Front Left Door Lock Motor Unlocking Power Supply

5 - -

6 0.85 BU Front Left Door Lock Motor Locking Power Supply

Front Left Door Power Window Switch


2 2.0 RD/WH Passenger Side Door Glass Up Control

3 2.0 GN/WH Passenger Side Door Glass Down Control

4 2.0 RD Driver Side Door Glass Up Power Supply

5

1 2 3

4 6

D01

57

23

6

1

8 4

D02

M201 2014.01





6 2.0 RD/YE Front Right Door Control Power Supply Output

7 2.0 WH/BN Power Window Main Switch Power Supply

8 2.0 GN Driver Side Door Glass Down Power Supply

Front Left Door Power Window Motor

2 1

D03

Pin No. Wire Diameter/Color Function1 2.0 GN Driver Side Door Glass Down Power Supply

2 2.0 RD Driver Side Door Glass Up Power Supply

Front Left Speaker

1

2

D04

Pin No. Wire Diameter/Color Function1 0.5 RD/BK Front Left Speaker Negative

2 0.5 RD Front Left Speaker Positive

6.1.7-56

M201 2014.01




Front Right Speaker

1

2

D05

Pin No. Wire Diameter/Color Function1 0.5 BU/BK Front Right Speaker Negative

2 0.5 BU/RD Front Right Speaker Positive

Front Right Door Power Window Motor

2 1

D06


1 2.0 GN Passenger Side Door Glass Down Power Supply

2 2.0 RD Passenger Side Door Glass Up Power Supply

M201 2014.01




Front Right Door Power Window Switch

57

23

6

1

8 4

D07

Pin No. Wire Diameter/Color Function1 2.0 RD Passenger Side Door Glass Up Power Supply

2 2.0 GN/WH Passenger Side Glass Down Signal Controlled by Driver Side

3 2.0 GN Passenger Side Door Glass Down Power Supply

4 2.0 BK Grounding

5 - -

6 2.0 RD/WH Passenger Side Glass Up Signal Controlled by Driver Side

7 2.0 RD/YE Front Right Door Control Power Supply

8 2.0 BU/YE Front Right Door Power Window Switch Power Supply

Front Right Door Fastener

2 1

D08


1 0.85 BU Front Right Door Lock Motor Locking Power Supply

2 0.85 WH Front Right Door Lock Motor Unlocking Power Supply

6.1.7-58

M201 2014.01




Right Backup Lamp

2 1

D09


2 0.5 RD Right Backup Lamp Power Supply

Right License Plate Lamp

1

2

D10

Pin No. Wire Diameter/Color Function1 0.5 RD/YE Right License Plate Lamp Power Supply

2 0.5 BK Grounding

M201 2014.01




Left License Plate Lamp

1

2

D11

Pin No. Wire Diameter/Color Function1 0.5 RD/YE Left License Plate Lamp Power Supply

2 0.5 BK Grounding

Left Backup Lamp

2 1

D12


2 0.5 RD Left Backup Lamp Power Supply

6.1.7-60

M201 2014.01



High Mounted Stop Lamp

2 1

D13


2 0.5 GN/WH High Mounted Stop Lamp Power Supply

M201 2014.01


Roof Wiring Harness Connector (L--)

L01 Wiring Harness Connector Pin Definition


Front Interior Roof Lamp

1 2 3

L01

Pin No. Wire Diameter/Color Function1 0.5 BK Front Roof Lamp Grounding

2 0.5 WH Front Roof Lamp Power Supply

3 0.5 BK/RD Front Roof Lamp DR Signal Output

Reading Lamp

31 2

L02

Pin No. Wire Diameter/Color Function1 0.5 BK/RD Reading Lamp DR Signal Output

2 0.5 WH Reading Lamp Power Supply

3 0.5 BK Reading Lamp Grounding

6.1.7-62

M201 2014.01




Overhead Evaporator Blower

1

2

L03

Pin No. Wire Diameter/Color Function1 2.0 BK/YE Blower Power Supply Output

2 2.0 RD/BK Blower Power Supply Input

Blower Resistor

3

1

2

L04

Pin No. Wire Diameter/Color Function1 2.0 BK/YE Blower Resistor Power Supply

2 0.85 LU Blower Resistor 2

3 0.85 VT Blower Resistor 1

M201 2014.01



Blower Switch

12

34

L05

Pin No. Wire Diameter/Color Function1 0.85 VT Blower Power Supply Input 1

2 2.0 BK Grounding

3 0.85 LU Blower Power Supply Input 2

4 2.0 BK/YE Blower Power Supply Input 3

M201 2014.01

6.1.8-1 6.1.8-1Abbreviation

Abbreviation List

Abbreviation English Full Name Chinese NameA/C Air Conditioning 空调

AAT Ambient Air Temperature 大气温度

ABS Anti-lock Brake System 防抱死制动系统

AM/FM Amplitude Modulation/ Frequency Modulation 调幅 / 调频

APP Accelerator Pedal Position 加速踏板位置

ASR Acceleration Slip Regulation 加速防滑控制系统

AT Automatic Transmission 自动变速器

ATF Automatic Transmission Fluid 自动变速器油

BCM Body Control Module 车身控制模块

CAN Controller Area Network 控制器局域网

CD Compact Disc CD

CHMSL Center High Mounted Stop Lamp 中央高位制动灯

CKP Crankshaft Position Sensor 曲轴位置传感器

CMP Camshaft Position Sensor 凸轮轴位置传感器

CRK Crank 曲轴

DDM Driver Door Module 驾驶员门控模块

DLC Data Link Connector 诊断接口

DOHC Double Overhead Camshaft 双顶置凸轮轴

DTC Diagnostic Trouble Code 故障代码

DVD Digital Video Disk DVD

EBD Electric Brakeforce Distribution 电子制动力分配

ECM Engine Control Module 发动机控制模块

ECT Engine Coolant Temperature 发动机冷却液温度

EGR Exhaust-Gas Recirculation 废气再循环

EOBD European On Board Diagnostic 欧洲车载诊断系统

ESP Electronic Stability Program 电子稳定程序

ETC Electronic Throttle Control 电子节气门控制

EVAP Evaporative Emission Control System 燃油蒸发排放系统

FWD Front Wheel Drive 前轮驱动

GPS Global Positioning System 全球定位系统

GVM Gross Vehicle Mass 车辆总重量

HCU Hydraulic Control Unit 液压控制单元

HFM Hands Free Module 免提电话模块

HID High Intensity Discharge 高强度放电

HO2S Heated Oxygen Sensor 氧传感器

HVAC Heating, Ventilation and Air Conditioning 暖风、通风和空调总成

I/P Instrument Panel 仪表板

6.1.8 Abbreviation

6.1.8-2

M201 2014.01

6.1.8-2Abbreviation

Abbreviation English Full Name Chinese NameIAC Idle Air Control Valve 怠速空气控制阀

IAT Intake Air Temperature 进气温度

ICU Integrated Control Unit 集成控制单元

IPC Instrument Panel Cluster 组合仪表

ISO International Standards Organization 国际标准化组织

ISS Input Shaft Speed 输入轴转速传感器

KS Knock Sensor 爆震传感器

LED Light Emitting Diode 发光二极管

LF Left Front 左前

LIN Local Interconnect Network 局部互联网络

LR Left Rear 左后

MAF Mass Air Flow 质量空气流量

MAP Manifold Absolute Pressure 进气歧管绝对压力

MIL Malfunction Indicator Lamp 故障指示灯

MP3 MPEG Audio Layer 3 MP3

MT Manual Transmission 手动变速器

MTC Manual Temperature Control 手动温度控制

MY Model Year 车型年款

OBD-II On Board Diagnostic II 第二代车载诊断系统

OEM Original Equipment Manufacturer 原始设备制造商

PAM Parking Aid Module 停车辅助模块

PCV Positive Crankcase Ventilation 曲轴箱强制通风

PDC Power Distribution Center 配电中心

PDM Passenger Door Mudule 乘客门控模块

PIN Personal Identification Number 个人身份号码

PWM Pulse Width Modulation 脉宽调制

RF Right Front 右前

RR Right Rear 右后

SAE Society of Automotive Engineers 美国汽车工程师学会

SAS Steering Angle Sensor 转向角度传感器

SCCM Steering Column Control Module 转向管柱控制模块

SDM Supplemental Diagnostic Module 安全气囊控制模块

SFI Sequential Fuel Injection 顺序燃油喷射

SOHC Single Overhead Camshaft 单顶置凸轮轴

SRI Service Reminder Indicator 维修提示指示灯

SRS Supplemental Restraint System 安全气囊系统

TCC Torque Converter Clutch 变矩器离合器

TCM Transmission Control Module 变速器控制模块

M201 2014.01

6.1.8-3 6.1.8-3Abbreviation

Caution：For abbreviations not in this list, please refer to the M201 Service Manual.

Abbreviation English Full Name Chinese NameTIR Total Indicator Reading 百分表总读数

TPMS Tire Pressure Monitoring System 轮胎压力监控系统

TPS Throttle Position Switch Sensor 节气门位置开关传感器

TRS Transmission Range Sensor 变速器档位传感器

TSB Technical Service Bulletin 技术服务公报

TWC Three-way Catalyst 三元催化转换剂

VFD Vacuum Fluorescent Display 真空荧光显示器

VIN Vehicle Identification Number 车辆识别码

VSS Vehicle Speed Sensor 车速传感器

WSS Wheel Speed Sensor 轮速传感器

Documents

- Tiger Trucktigertruck.com/wp-content/uploads/2015/12/M201_Wiring... · 2016-10-07 · Read Wiring Diagram and Analyze Causes Make a complete