Oracle.Pass4sure.1z0-597.v2015-03-27.by.Forrest - … · Which three are included for each test in the Enterprise Installation Standards (EIS) ... On a SPARC T4 server running Oracle

http://www.gratisexam.com/

Pass4sure 1z0-597 51q

Number: 1z0-597Passing Score: 800Time Limit: 120 minFile Version: 18.5


1z0-597

SPARC T4-Based Server Installation Essentials

Passed on 2-02-15 with an 890. Dump still valid in US. 1 or 2 new questions. You must know the material as answers are worded differently at times.


Exam A

QUESTION 1To disable ILOM CLI session time-out, which command should be used?

A. Set /SP/cli timeout = nB. Set /SP/cli timeout = disableC. Set /SP/cli timeout = 0D. Set /SP/cli timeout = 1000

Correct Answer: DSection: (none)Explanation

Explanation/Reference:References:

QUESTION 2Which three are included for each test in the Enterprise Installation Standards (EIS) Test procedure Plan?

A. The test objectiveB. The test methodC. The expected outcome of the testD. Troubleshooting for each failed test

Correct Answer: ABCSection: (none)Explanation

Explanation/Reference:Explanation:

QUESTION 3In planning for the installation of a SPARC T4 server, you notice that a more recent version of a patch is available than what is currently on the EIS-DVD. Accordingto the Enterprise Installation Standards (EIS) methodology, what should you do?

A. Always install the most recent version of a patchB. Delay Installation until the updated patch is published to the EIS-DVDC. Do not Install the patch, unless instructed to do so by an EIS-Alert


D. Never Install patches outside of the EIS-DVD

Correct Answer: ASection: (none)Explanation


QUESTION 4The SPARC T4-2 server has ___________ than the SPARC T4-1 server.


A. 512 GB more memoryB. 1 TB more memoryC. 64 more compute threadsD. 128 more compute threads

Correct Answer: BSection: (none)Explanation


QUESTION 5Based on the Enterprise Installation Standards (EIS), why should Oracle Explorer Data Collector be run with the "-i" switch after initial system power-on and setupare complete?

A. To remove confidential customer IP addresses from the Explorer outputB. To provide a baseline of the initial system configurationC. To collect local Intelligent Platform management Interface (IPMI) data


D. To collect remote Oracle ILOM snapshot data

Correct Answer: CSection: (none)Explanation


QUESTION 6What package should be installed if you wish to harden the control domain on a SPARC T4 server running Oracle Solaris 10 and Oracle VM Server for SPARC 2.1?

A. SUNWldmB. SUNWdmp2vC. SUNWsstD. SUNWjass



QUESTION 7What is main objective of having Enterprise Installation Standards (EIS)?

A. To create a framework for tracking improperly installed systemsB. To produce consistent, high quality installationsC. To produce systems optimized for Oracle software deploymentsD. To create a framework for tracking properly installed systems




QUESTION 8How many XAUI (10 GbE Attachment Unit Interfaces) ports are provided per SPARC T4 processor?

A. 1B. 2C. 3D. 4



QUESTION 9Which two statements are true regarding the Stream processing Unit (SPU) on the SPARC T4 processor?

A. The SPU is implemented within each processor core.B. The SPU is shared across all cores on the processor.C. The SPU operates at the same clock speed as the core.D. The SPU archives wire-speed performance for encryption only.

Correct Answer: ACSection: (none)Explanation


QUESTION 10You have configured DNS and have determined that the services processor serial number for your target server is 0641AMA007. What is the host name of thisserver?

A. SUN-0641AMA007B. SUNCMM0-0641AMA007C. SUNCMM1-0641AMA007D. SUNSP-0641AMA007




QUESTION 11According to the Enterprise Installation Standards (EIS) on electrical grounding, what is the benefit of additional grounding points?


A. Protect systems by helping to avoid leakage currentB. Allows racks to support either AC or DCC. Allows a rack to support more than two dedicated circuit feeds for higher redundancyD. Allows a rack to support more than one UPS system for higher redundancy



QUESTION 12Error conditions by POST, Oracle Solaris Predictive Self-Healing (PSH), and Oracle ILOM are forward to which component for fault handling?

A. POSTB. Oracle VTSC. Oracle ILOMD. Oracle Solaris PSH

Correct Answer: C


Section: (none)Explanation


QUESTION 13You plan on creating a RAID volume to mirror the system disks. After you have selected a controller, what fcode command should be run to list the physical driverson the controller?

A. Show-devsB. Show-volumeC. Show-childrenD. Show-drives



QUESTION 14In general, when labeling a cable, the host connection should follow the format: <system name> <board no.> <slot no.> and _____________.

A. <port no.>B. <insertion point>C. <cable no.>D. <rack no.>



QUESTION 15In the following example, Power On Self Test (POST) reports an uncorrectable memory error affecting the following locations:


/SYS/PM0/CMP0/B0B0/CH1/D0/SYS/PM0/CMP0/B0B1/CH1/D0

The error was detected by POST running on which node, core, and standard?

A. Node 0, core 7, strand 2B. Node 2, core 7, strand 0


C. Node 7, core 2, strand 0D. Node 0, core 2, strand 7



QUESTION 16According to Enterprise Installation Standards (EIS), which is recommended when creating virtual disk devices for use in guest domain?

A. Create a new volume from an existing ZFS poolB. Use file containersC. Use the file containers and ZFS clones to multiply imagesD. Use a disk slice directly



QUESTION 17You lost your Oracle ILOM settings after a service processor firmware update. Why?

A. You did not enable the Preserve Configuration option.B. You did not back up the Oracle ILOM configuration.C. Oracle ILOM settings must be re-established after every firmware update.D. You used the Oracle ILOM web interface rather than the CLI to perform the update.




QUESTION 18On a SPARC T4 server running Oracle Solaris 10, you execute the following command:# lucreate c sol_run m /:/dev/dsk/c0t4d0s0:ufs \ -m /usr:/dev/dsk/c0t4d0s3:ufs n sol_tan

What is the result?


A. Create a new boot environment named "sol_tan" and name the active boot environment "sol_run".B. Create a new boot environment named "sol_named" and name the active boot environment "sol_tan".C. Replaces the existing boot environment "sol_run" with "sol_tan"D. Replaces the existing boot environment "sol_tan" with "sol_run"



QUESTION 19You have the Oracle ILOM keyswitch_state=standby. What is the Impact ?

A. The system will power on and run power-on self-test (POST), but Oracle Solaris will not boot.B. The system will power on and run power-on self-test (POST), but no flash updates can be made.C. The system cannot power on.D. The system powers on, but does not run power-on self-test (POST) or boot Oracle Solaris.




QUESTION 20Power-on self-test (POST) detected a faulty core on a SPARC T4-2 server. The server supports an important internal application for the customer. What is the stateof the application and why?

A. The application is unavailable until the processor with the faulty core has been replaced.B. The application is available with limited computing resources since POST disabled the processor with the faulty core.C. The application is available since POST disabled the faulty core.D. The application is unavailable until the processor with the faulty core has been disabled by the system administrator.



QUESTION 21Below is a list of boot environments available on a SPARC T4 server running Oracle Solaris 11.Which boot environment is currently booted?

A. S11ampB. SolarisC. Solaris 151aD. Solaris 174




QUESTION 22On a SPARC T4 server running Oracle Solaris 11, you execute the following:

% beaddm create alt_krit

What is the result?

A. Creates a snapshot of the boot environment "alt_krit"B. Makes "alt_krit" the default boot environmentC. Renames the default boot environment to "alt_krit"D. Creates a new boot environment named "alt_krit"



QUESTION 23You are installing a SPARC T4 server at a customer site using a single-phase power feed. The power outlet is 15 meters (16.4 feet) from device. Which EnterpriseInstallation Standard (EIS) document would you have highlighted this issue prior to installation?

A. Site audit reportB. Test procedure planC. Power routing mapD. Server operational checklist




QUESTION 24On SPARC T4-2 server, if the memory riser has four dual-rank DIMMs, its bandwidth is approximately 94% of the possible maximum. If the memory riser has onlytwo dual-rank DIMMs, what is the approximate bandwidth as a percent of the total bandwidth?

A. 29%B. 35%C. 41%D. 47%



QUESTION 25Activating Auto Service Request (ASR) Assets _________.

A. Is done on the Asset onlyB. Is done on both the Asset and the ASR Manager systemC. Is done on the ASR Manager system onlyD. Is done on My Oracle Support only



QUESTION 26According to the Enterprise Installation Standards (EIS) for SPARC T4 servers running Oracle Solaris 10, what steps are required in order to configure the server touse Auto Service Request (ASR)?

A. 1. Enable ILOM telemetry 2. Activate the ASR Asset


B. 1. Enable SunMC telemetry2. Enable FMA telemetry3. Activate the ASR AssetC. 1. Enable SunMC telemetry2. Activate the ASR AssetD. 1. Enable ILOM telemetry2. Enable FMA telemetry 3. Activate the ASR Asset



QUESTION 27The _________ runs its own embedded operating system.


A. Logical Domains ManagerB. Oracle ILOM service processorC. OpenBoot PROMD. Hardware Management Pack



QUESTION 28You have set up several guest domains on a SPARC T4 server. Which operating system(s) are supported in these guest domains?

A. Oracle Solaris onlyB. Oracle Linux only


C. Oracle Solaris or Oracle LinuxD. Oracle Solaris, Oracle Linux, and OpenSolaris



QUESTION 29The amount of disk space recommended by the Enterprise Installation Standards (EIS) for the root slice is __________ for UFS File and Solaris 10.

A. 5 GBB. 10 GBC. 13 GBD. 18 GB



QUESTION 30As part of a server consolidation project, a customer would like to run Solaris 9-based applications on a SPARC T4 server. What technology is required?

A. Oracle VM Server for SPARCB. Oracle Solaris ContainersC. Dynamic DomainsD. Oracle VirtualBox




QUESTION 31During installation, what happens if both power supplies are not cabled at the same time on a SPARC T4-2 server?

A. NothingB. OpenBoot PROM is disabledC. The service processor will not power onD. The Oracle ILOM will signal a fault



QUESTION 32What is Critical Thread Optimization?

A. The ability to dynamically allocate core resources among active threadsB. The ability to bind individual threads to a processorC. Part of the Processor Sets feature of Oracle Solaris that defines a group of logical processors and schedules threads on them.D. Recognized by Oracle Solaris Scheduler as a thread that should run by itself on a single core



QUESTION 33You have printed the partition (slice) information for a disk. What type of label does it have?


A. SMIB. EFI


C. e2labelD. xfs_admin



QUESTION 34Using the logical domain configuration below, what is the domain and virtual CPU corresponding to physical CPU number 5?


A. domain primary, virtual CPU number 0B. domain primary, virtual CPU number 1C. domain ldg2, virtual CPU number 0D. domain ldg1, virtual CPU number 1

Correct Answer: DSection: (none)


Explanation


QUESTION 35After the Logical Domains Manager has been installed, what happens to the original system and instance of Oracle Solaris?

A. It becomes the control domainB. It becomes the first guest domainC. It is automatically configured as a service domainD. Nothing Logical domains are created on top of the original instance of Oracle Solaris.



QUESTION 36In the OpenBoot PROM environment, you used the "show-children" command to list the physical drives on a specific RAID controller. The output is below. Whichcommand creates a RAID 0 volume with targets 9 and a?


A. 9 a create-raid0-volumeB. Create raid-volume = 0 9 aC. 9 a create-raid-volume = 0D. Create raid0-volume = 9 a



QUESTION 37During the acclimatization process, what is the maximum positive or negative temperature gradient that is permitted for multi-layer boards?

A. Approximately 2° C (4° F) per hourB. Approximately 4° C (7° F) per hourC. Approximately 6° C (11° F) per hourD. Approximately 8° C (4° F) per hour



QUESTION 38According to the Enterprise Installation Standards (EIS), what is the recommended minimum amount of memory that should be allocated to the control domain?



A. 2 GBB. 3 GBC. 4 GBD. 6 GB



QUESTION 39When sizing the /var partition on a UFS file system, you have estimated the /var/sadm area to have 20 GB. Why?

A. It is enough space to hold several complete crash dumps.B. It is rough space to hold package and patch information.C. It is enough space to hold logs and spoolsD. It is identical to the space allocated for the root slice, which is 20 GB on this particular system.



QUESTION 40A power supply fails on a SPARC T4-4 server and a replacement is not available. What should you do?

A. Remove the failed power supply immediatelyB. Leave the failed power supply installedC. Power down the serverD. Unconfigure the failed power supply




QUESTION 41According to the Enterprise Installation Standards (EIS), what is the minimum amount of time SunVTS should be run?

A. 10 minutesB. 20 minutesC. 30 minutesD. 1 hour



QUESTION 42Which two tasks are required to install and configure Oracle VM Server for SARC Management Information Base (MIB) software?

A. Install Oracle VM Server for SPARC MIB software on the primary and guest domainsB. Install Oracle VM Server for SPARC MIB software on the primary domain onlyC. Load the Oracle VM Server for SPARC MIB module into the Oracle Solaris SMAD. Load the Oracle VM Server for SPARC MIB module into the Oracle Solaris FMA

Correct Answer: BCSection: (none)Explanation


QUESTION 43You need to hot-plug a hard drive, which is not a boot device, while the server is online. Which action is required before removing the drive?

A. Verify that the green OK-to-OK LED is lit on the hard drive.B. Take the drive offline before removing.


C. Temporarily shut down the OS.D. Run the cfgadm c configure command.



QUESTION 44You are unable to add an Oracle ILOM user account, what is one possibility that would cause this issue?

A. You need to add SSH keys to the system before creating additional user accounts.B. You do not have the user management role enabled.C. You do not have the host control role enabled.D. You have exceeded the maximum number of 5 user accounts.



QUESTION 45When preparing to update the firmware, which two statements are true?

A. If performed via the ILOM interface, the firmware file should reside on the system from which the browser is launched.B. If performed via the ILOM web interface, a TFTP server is required.C. If performed via the ILOM CLI, a TFTP server is required.D. Firmware updates can only be performed via the ILOM CLI.




QUESTION 46You are trying to reach the OpenBoot prompt (ok) from Oracle Solaris on a SPARC T4-1 system running Oracle VM Server for SPARC. The OpenBoot firmware isnot available. Why is the OpenBoot prompt not available?

A. It has been removed from memory.B. It was not installed on the system.C. The service processor property "auto-boot" is disabled.D. An incorrect version of OpenBoot firmware is installed.



QUESTION 47A faulty DIMM needs to be replaced on a SPARC T4-2 server. What are two ways to determine which DIMM on a memory riser is faulty?

A. Run the Oracle ILOM show faulty command.B. Run Oracle VTS software.C. Run the Oracle ILOM al command.D. Press the Remind button on the memory riser.

Correct Answer: ADSection: (none)Explanation


QUESTION 48During the initial installation of a SPARC T4-2 server, you notice the SP NET MGT port is not available. What is one possibility?

A. The SPARC T4-2 does not use the SP NET MGT port.B. It must be connected to a Gigabit network.C. The network does not use DHCP.D. The Oracle ILOM is down.




QUESTION 49You are troubleshooting an installation and have run Oracle Explorer Data Collector. What should you do with the output?

A. Have it analyzed by the Oracle Risk Analysis Services (ORAS) knowledge engine.B. Have it analyzed by the Remote Diagnostic Agent (RDA) tool.C. Review the output and address the identified configuration errors.D. Calculate the system operational risk (e.g., the chance of the system to go out of service due to a hardware issue.)



QUESTION 50You have set up power on self test (POST) to run when the scrvrr has been reset by the user. The customer would like POST to run any error-invoked reset. How isthis accomplished?

A. Change the diagnostic level to "max" (user_reset_level = max).B. Change the diagnostic trigger to "error reset" (trigger = error-reset).C. Change the verbosity to "debug" (user_reset__verbosity = debug).D. Change the diagnostic trigger to "power on-reset" (trigger = power-on-reset).




QUESTION 51Why are Electrostatic Discharge (ESD) "soft failures" the most serious type of failures?

A. The damage is not immediately noticed or detected.B. The damage is immediate and easily detected.C. The damage corrupts firmware.D. The damage results in the failure of the entire system.


Explanation/Reference:


Documents

Oracle.Pass4sure.1z0-597.v2015-03-27.by.Forrest - … · Which three are included for each test in the Enterprise Installation Standards (EIS) ... On a SPARC T4 server running Oracle