01, Front Cover - Alamo Industrial · 1. The purchase order must include the Name, Address (Ship to Street Address) of the Person / Organization ordering the parts. Who / How Parts

© 2004 Alamo Group Inc.

SWITCHBLADE5 & 6 Foot

COMPLETE PARTSLISTING

ALAMO INDUSTRIAL1502 E. WalnutSeguin, Texas 78155830-372-3551

ARCHIVE BOOKBy Serial Number / Production Mar. 2001 to Oct. 2003 (Current)

(SWB5 & SWB6 Models)

2004 Edition

Archive BookPart No.

0297944301/04

© 2004 Alamo Group Inc. Parts Section -3

The Switchblade (SWB5 & SWB6) Archive Book is a complete listing of Parts from the first Unit tothe Present. The Production Dates, Serial Numbers, Special Notes and Descriptions are furnishedto help find Replacement Parts. Dimension (if listed) are for Identification of Parts and MAY NOT beto Manufacturing Specification, Your measurements may vary some from dimensions listed. SomeParts may be changed and be different than parts listed. Some Modification may be required whenreplacing older parts. Match S/N's listed in the rear of this Book with the Ship Dates listed at the topof each Parts Page. This is because of the wide range of Model sizes using these S/N's (Currentmeans this model is still in pruduction at the time this manual was printed)

May 2001to

Current

S/N SB5-01001of

S/N SB5-Current

FRAMEASSEMBLY

Beginning Production Date

Ending Production Date Componets Listed This Page

PAGE EXAMPLE

For ordering parts the following instructions are offered to help eliminate delay

1. The purchase order must include the Name, Address (Ship to Street Address) of thePerson / Organization ordering the parts. Who / How Parts should be Billed. Name andPhone Number of a Contact Person at your end.

2. The Purchase Order must list clearly the correct Part Number of Part. Quantity of eachPart wanted, Complete and correct Description of each Part. All Parts will be shipped asrequested depending on availability and/or reasonability of request carrier / method.

3. Alamo Industrial reserves the right to substitute parts where applicable and change pricesWithout prior notice. Alamo Industrial also reserves the right to Ship Parts the mostReasonable way as determined by Alamo Industrial.

4. Some Parts are unlisted items, which are special production items not normally stockedor built for a limited / special use, These parts may be subject to special handling orcannot be priced till ordered. Always Request a quotation for such Parts before sending apurchase order.

INTRODUCTION

SWITCHBLADE 5 & 6 FOOTSICKLE BAR

ARCHIVE BOOK

Beginning S/N

Ending S/N


INDEX - SWITCH BLADE5 ft & 6 ft

ITEM PAGE NO.

INTRODUCTION SWITCH BLADEModel Parts Introduction....................................................................3

BAR TILT CYLINDER5 & 6 Foot Model............................................................................... 22

BREAK-A-WAY ASY.5 & 6 Foot Model............................................................................... 28, 29

CARRIAGE ARM ASY5 & 6 Foot Model............................................................................... 20, 21

COMMON COMPONENT BOX5 & 6 Foot Model............................................................................... 30, 31

CONTROL VALVEMechanical Valve & Handles.............................................................. 40, 41Solenoid Valve)..................................................................................43Remote Control Valve & Stand............................................................ 46, 47Remote Control Handles & Cables.......................................................44, 45

CURB LIFT CYLINDER5 & 6 Foot Model............................................................................... 23

DECALS & LOCATION CHART5 & 6 Foot Model............................................................................... 50 trhu 54

FILTER ASY5 & 6 Foot Model............................................................................... 48, 49

HYDRAULIC MOTOR ASY5 & 6 Foot Model............................................................................... 38, 39

HYDRAULIC PUMP ASY5 & 6 Foot Model (1.16 / 0.49 Cu In.)................................................... 34,355 & 6 Foot Model (0.98 / 0.37 Cu In.)................................................... 36,37

HYDRAULIC TANK ASY5 & 6 Foot Model............................................................................... 32, 33

KNIFE DRIVE ASY5 & 6 Foot Model............................................................................... 24, 25

MOUNT KIT, Hydraulic Kits & Sub-frame KitsAll, By Tractor Model..........................................................................56 thru 89

SAFETY SECTION5 Foot Model..................................................................................... 7 thru 12

SERRATED KNIFE BAR ASY5 & 6 Foot Model............................................................................... 18, 19

SHOE, DRIVE ASY.5 & 6 Foot Model............................................................................... 26, 27

SICKLE BAR ASY5 Foot Model..................................................................................... 14, 156 Foot Model..................................................................................... 16, 17

WIRE HARNESS5 & 6 Foot Model............................................................................... 42



TRACTOR MOUNT KITSTRACTOR MODEL PAGE NO.

INTRODUCTION SWITCH BLADE MOUNT KIT COMPONENT LIST Introduction........................................................................................................................... 56

CASE - IHHose Schematic................................................................................. 57

3220,Rops, 2 WD Row Crop Bolster .............................................................. 58

385, 395,Rops, 2 WD & 4 WD Row Crop Bolster ................................................. 59

485, 495,Rops, 2 WD & 4 WD Row Crop Bolster .................................................. 60

585, 685, 595, 695,Rops, 2 WD Row Crop Bolster ............................................................. 61

C50, C60,Rops, 2 WD Row Crop Bolster .............................................................. 62

FORD - NEW HOLLANDHose Schematic................................................................................. 63

335, 340, 540, 2000, 2600, 3000, 3100, 3400, 3600, 4000SU, 4100SU, 4600SU,Rops, 2 WD .........................................................................................64

2310, 2610, 2810, 3910, 3610, 4610SU,Rops, 2 WD .........................................................................................65

250C, 260C, 340A, 445, 545, 540A, 3230, 3430, 3930Rops, 2 WD .........................................................................................66

4610, 4630Rops, 2 WD ........................................................................................ 67Cab, 2 WD & 4 WD.............................................................................. 68

5635Cab, 2 WD ......................................................................................... 69

TN55, 65, 70, 75Rops, 2 WD & 4 WD (Single Wing RH)................................................... 70Rops, 2 WD (Dual Wings RH & LH)....................................................... 71

TN55D, 65D, 70D, 75DCab, 2WD (Single RH Wing)................................................................ 72Cab, 4WD (Single RH Wing)............................................................... 73Cab, 4WD (w/ Loader)........................................................................ 74

TL80, 90, 100Cab, 2 WD & 4 WD (Single Wing RH).................................................... 75Rops, 2 WD & 4 WD (Single Wing RH).................................................. 76Cab, 2 WD & 4 WD (Dual Wings RH & LH)............................................ 77

TS SERIESCab, 2 WD & 4 WD (Single Wing RH)................................................... 78



TRACTOR MOUNT KITSTRACTOR MODEL PAGE NO.

JOHN DEEREHose Schematic................................................................................... 79

4500, 4600, 4700Rops, 4 WD .........................................................................................80

5200, 5300, 5400Rops, 2 & 4 WD ...................................................................................81

5210, 5310, 5410Rops, 2 & 4 WD .................................................................................. 82Cab, 2 & 4 WD .................................................................................... 83

5220, 5320Rops, 2 WD (w/ Straddle Mount Platform)............................................... 84

6200, 6300, 6400Rops, 2 & 4 WD ...................................................................................85

KUBOTAHose Schematic................................................................................... 86

L3750, L4150Rops, 2 & 4 WD .................................................................................. 87

MASSEY FERGUSONHose Schematic................................................................................... 88

1433V, 1440VRops, 2 & 4 WD .................................................................................. 89

SAFETYSECTION

Safety Section - 7© 2003 Alamo Group Inc.

Safety Section - 8

SAFETY


Read these assembly instructions through completely and understand thembefore proceeding with the assembly of the equipement.

A safe and careful operator is the best operator. Safety is of primary importance to the manufac-turer and should be to the owner/operator. Most accidents can be avoided by being aware ofyour equipment, your surroundings, and observing certain precautions. The first section of thismanual includes a list of Safety Messages that, if followed, will help protect the operator andbystanders from injury or death. Read and understand these Safety Messages before assem-bling, operating or servicing this Implement. This equipment should only be operated by thosepersons who have read the Manual, who are responsible and trained, and who know how to doso safely and responsibly.

The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout thismanual and on decals which are attached to the equipment. The Safety Alert Symbol means:“ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and SignalWord are intended to warn the owner/operator of impending hazards and the degree of possibleinjury faced when operating this equipment..

CAUTION! The lowest level of Safety Message; warns of possible injury. Decals located on the Equipment with this Signal Word are Black and Yellow.

WARNING! Serious injury or possible death! Decals are Black and Orange.

DANGER! Imminent death/critical injury. Decals are Red and White. (SG-1)

Practice all usual and customary safe working precautions andabove all---remember safety is up to YOU. Only YOU can preventserious injury or death from unsafe practices.

Safety Section - 9

SAFETY

© 2003Alamo Group Inc.

Si no lee Ingles, pida ayuda a alguien que si lo lea para que letraduzca las medidas de seguridad. (SG-3)

PELIGRO!

!LEA EL INSTRUCTIVO!

READ, UNDERSTAND, and FOLLOW the following SafetyMessages. Serious injury or death may occur unless care istaken to follow the warnings and instructions stated in the SafetyMessages. Always use good common sense to avoid hazards.

(SG-2)

!Si no lee Ingles, pida ayuda a alguien quesi lo lea para que le traduzca las medidasde seguridad. (SG-3)

PELIGRO! LEA ELINSTRUCTIVO!

WARNING! Perform service, repairs and lubrication according to the maintenance section. Ensure the unitis properly lubricated as specified in the lubrication schedule and all bolts and nuts are properlytorqued. Failure to properly service, repair and maintain this Implement in good operatingcondition could cause component failure and possible serious injury or even death. (SG-35)

WARNING! Operate this Equipment only with a Tractor equipped with anapproved roll-over-protective system (ROPS). Always wear seatbelts. Serious injury or even death could result from falling off thetractor--particularly during a turnover when the operator could bepinned under the ROPS. (SG-7)

DANGER! Never work under the Implement, the framework, or any lifted compo-nent unless the Implement is securely supported or blocked up toprevent sudden or inadvertent falling which could cause serious injuryor even death. (SG-14)

WARNING! Use caution and wear protective gloves when handling sharp objects such as blades, knives,and other cutting edges. Be alert to worn component surfaces which have sharp edges. Sharpsurfaces can inflict severe laceration injuries if proper hand protection is not worn. (SG-37)

Safety Section - 10

SAFETY


Many of the parts are heavy and require lifting assistance. Do not try tolift the heavy parts by yourself. Get help from another employee or froman overhead crane.

WARNING! The operator and all support personnel should wear hard hats,safety shoes, safety glasses, and proper hearing protection at alltimes for protection from injury including injury from items thrown bythe equipment. (SG-16)

Always wear safety shoes with steel toes when working on this equipment.It is recommended that the safety shoes have metatarsal guards.

When welding use Welding hood with the appropriate OSHA requiredprotective lens, welding apron, and welding gloves.

DANGER! Always disconnect the wire leads from the mower valve solenoid beforeperforming service on the Tractor or Mower. Use caution when workingon the Tractor or Mower. Tractor engine must be stopped beforeworking on Mower or Tractor. The Mower Blades could inadvertently beturned on without warning and cause immediate dismemberment, injuryor death. (SBM-12)

DANGER! Never run the tractor engine in a closed building or without adequateventilation. The exhaust fumes can be hazardous to your health.

(SG-23)

WARNING!

WARNING!

WARNING!

Safety Section - 11

SAFETY

© 2003Alamo Group Inc.

Before starting the mower make sure the area is clear and the floor hasbeen swept. The mower blade can throw objects several hundred feet.Thrown objects could damge property or cause severe bodily injuries evendeath.

WARNING! Make certain that the “Slow Moving Vehicle” (SMV) sign is installed insuch a way as to be clearly visible and legible. When transporting theEquipment use the Tractor flashing warning lights and follow all local trafficregulations. (SG-6)

DANGER! Start tractor only when properly seated in the Tractor seat. Starting atractor in gear can result in injury or death. Read the Tractor operatorsmanual for proper starting instructions. (SG-13)

DANGER! Do not operate this Equipment with hydraulic oil leaking. Oil isexpensive and its presence could present a hazard. Do not check forleaks with your hand! Use a piece of heavy paper or cardboard. High-pressure oil streams from breaks in the line could penetrate the skinand cause tissue damage including gangrene. If oil does penetrate theskin, have the injury treated immediately by a physician knowledge-able and skilled in this procedure. (SG-15)

WARNING! Always read carefully and comply fully with the manufacturers instruc-tions when handling oil, solvents, cleansers, and any other chemicalagent. (SG-22)

DANGER! All Safety Shields, Guards and Safety devices including(but not limited to) - the Deflectors, Chain Guards, SteelGuards, Gearbox Shields, PTO integral shields , andRetractable Door Shields should be used and main-tained in good working condition. All safety devicesshould be inspected carefully at least daily for missingor broken components. Missing, broken, or worn itemsmust be replaced at once to reduce the possibility ofinjury or death from thrown objects, entanglement, orblade contact. (SGM-3)

DANGER!

Safety Section - 12

SAFETY


DANGER! NEVER use drugs or alcohol immediately before or while operating theTractor and Implement. Drugs and alcohol will affect an operator’salertness and coordination and therefore affect the operator’s ability tooperate the equipment safely. Before operating the Tractor or Imple-ment, an operator on prescription or over-the-counter medication mustconsult a medical professional regarding any side effects of the medi-cation that would hinder their ability to operate the Equipment safely.NEVER knowingly allow anyone to operate this equipment when theiralertness or coordination is impaired. Serious injury or death to theoperator or others could result if the operator is under the influence ofdrugs or alcohol. (SG-27)

DANGER! Operate the Tractor and/or Implement controls only while properly seatedin the Tractor seat with the seat belt securely fastened around you.Inadvertent movement of the Tractor or Implement may cause seriousinjury or death. (SG-29)

WARNING! Engine Exhaust, some of its constituents, and certain vehiclecomponents contain or emit chemicals known to the state ofCalifornia to cause cancer and birth defects or otherreproductive harm. (SG-30)

WARNING! Battery posts, terminals and related accessories contain leadand lead compounds, chemicals known to the state of Califor-nia to cause cancer and birth defects or other reproductiveharm. Wash Hands after handling. (SG-31)

WARNING! Use extreme caution when getting onto the Implement to perform repairs, maintenance andwhen removing accumulated material. Only stand on solid flat surfaces to ensure good footing.Use a ladder or raised stand to access high spots which cannot be reached from gound level.Slipping and falling can cause serious injury or death. (SG-33)

WARNING! Avoid contact with hot surfaces including hydraulic oil tanks, pumps, motors, valves and hoseconnections. Relieve hydraulic pressure before performing maintenance or repairs. Usegloves and eye protection when servicing hot components. Contact with a hot surface or fluidcan cause serious injury from burns or scalding. (SG-34)

WARNING! Avoid contact with hot surfaces of the engine or muffler. Use gloves and eye protection whenservicing hot components. Contact with a hot surface or fluid can cause serious injury fromburns or scalding. (SG-38)


SWB 5 & 6 (Archive Book) 01/04

NOTES



Mar. 2001to

CurrentS/N SWB5-10001

toS/N SWB5-Current

SICKLE BAR ASY5 Foot

8

4

9

19

136

14

146

14

6

146

14

6

18

11

7

7

7

7

7

12

12

12

12

15

5

10

10

10

10

73

3

7

12

16



ITEM PART NO. QTY. DESCRIPTION

02974360 - 5' Bar Asy

1 00001200 1 Nut2 00019600 1 Lockwasher3 00022200 2 Lockwasher4 000516 1 Carriage Bolt (1-3/4" Long)5 0012700 1 Knife Clip High6 0046400 10 Plow Bolt (1-1/2" Long)7 00999316 22 Nut8 0123800 1 Outer Shoe Sole9 0129000 1 Carriage Bolt (1-3/4" Long)10 0188700 4 Knife Clip11 02974345 1 Cutterbar 5'12 0532600 4 Wear Plate13 0570900 1 Outer Shoe Asy14 0571800 10 Plow Bolt (2" Long)15 0571900 1 Wear Plate16 0593600 1 Outer Rock Guard17 0593700 18 Center Rock Guard18 0593800 1 Inner Rock Guard19 12666000 1 Carriage Bolt (1-1/2" Long)

Mar. 2001to

Current

S/N SWB5-10001to

S/N SWB5-Current




Mar. 2001to

Current

S/N SWB5-10001to

S/N SWB5-Current


146

14

6

6

18

146

146

146

14

1112

12

12

12

12

15

5

10

10

10

10

10

7

7

7

7

7

7

3

7

1213

816

9

4

19



Mar. 2001to

Current

S/N SWB6-10001to

S/N SWB6-Current

ITEM PART NO. QTY. DESCRIPTION

02974372 - 6' Bar Assembly

1 00001200 1 Nut2 00019600 1 Lockwasher3 00022200 2 Lockwasher4 000516 1 Carriage Bolt (1-3/4" Long)5 0012700 1 Knife Clip High6 0046400 12 Plow Bolt (1-1/2" Long)7 00999316 26 Nut8 0123800 1 Outer Shoe Sole9 0129000 1 Carriage Bolt (1-3/4" Long)10 0188700 5 Knife Clip11 02974346 1 Cutterbar 6'12 0532600 5 Wear Plate13 0570900 1 Outer Shoe Assembly14 0571800 12 Plow Bolt (2" Long)15 0571900 1 Wear Plate16 0593600 1 Outer Rock Guard17 0593700 22 Center Rock Guard18 0593800 1 Inner Rock Guard19 12666000 1 Carriage Bolt (1-1/2" Long)




Mar. 2001to

Current

SERRATED KNIFEBAR ASY5 & 6 Foot

Knife Head WeldmentBlade Sections

Backing Strip

Note Orientation ofKnife Head Weldmnt

1

3

4

5

6

7

8

S/N SWB5-10001S/N SWB6-10001

toS/N SWB5-CurrentS/N SWB6-Current



Mar. 2001to

Current

SERRATED KNIFEBAR ASY5 & 6 Foot

ITEM PART NO. QTY Qty DESCRIPTION5' 6'

02974361 1 - 5' Serrated Knife Bar Asy02974373 - 1 6' Serrated Knife Bar Asy

1 0064600 21 25 Knife Sections (3")3 02974316 1 1 Insert Nylon Drive BRG Clamp4 02974349 1 1 Weldment Knife Head

00756328 1 1 Clamp Bolt5 02976270 35 43 Section Bolt - 5/86 02976271 9 9 Head Bolt 1-1/647 02976272 42 50 Section Locknut - Cone8 0530100M 1 - Backing Strip, 5'

0531900 - 1 Backing Strip, 6'

Note: 5 Foot Knife Bar Asy Shown, 6' is same except length and qty of knives.

S/N SWB5-10001S/N SWB6-10001




Mar. 2001to

Current

CARRIAGE ARM ASY

S/N SWB5-10001S/N SWB6-10001


8 6

7

6

6

REAR VIEWFRONT VIEW

11

312

4

3

11

11

3

1311

3

4

91,2 5

1, 2

5

6A

4



Mar. 2001to

Current

CARRIAGE ARMASY

ITEM PART NO. QTY DESCRIPTION

02974362 - Carriage Arm Assy.

1 000206 2 Red Lubricaps

2 00752670 2 Grease Fitting

3 00755153 4 Cotter Pin

4 0112700 2 Carriage Pin

5 0113400 2 Roll Pin

6 02045200 3 Elbow Adapter

6A 02961325 1 * Restrictor

7 02965475 1 Hose

8 02970702 1 Tee Adapter

9 02974324 1 Weldment Carriage Arm

10 02974329 1 Weldment Pivot Mount

11 0424200 4 Cylinder Lug Pin

12 0693400A 1 Curb Lift Cylinder

13 0693500A 1 Bar Tilt Cylinder

S/N SWB5-10001S/N SWB6-10001


* Note: Item 6A was not used on all units, it was only used in specialcases where the cyliners used did not have built in restrictors and cylindermovement was to fast, Cylinder should have built in restrictors to preventthe need for external restrictors. Only use this restrictor if needed to slowCylinder travel down.



Item Part No. Qty Description

00693500A - Bar Tilt Cylinder Asy1. 02977114 1 Tube Weldment2. 02977116 1 Cylinder Head3. 02977115 1 Rod Weldment4. ------------ 1 Wire Ring5. ------------ 1 O-Ring6. ------------ 1 Seal7. ------------ 1 Seal8. ------------ 1 Seal, Wiper Rod9. 02977121 1 Seal Kit (items 4,5,6,7 & 8)

213

4 5 67

8

Mar. 2001to

Current

BAR TILT CYLINDERP/N 0693500A

S/N SWB5-10001S/N SWB6-10001





00693400A - Curb Lift Cylinder Asy1. 02977114 1 Tube Weldment2. 02977116 1 Cylinder Head3. 02977118 1 Piston4. 02977122 1 Rod Weldment5. 02977123 1 Rod, Inner6. ------------ 1 O-Ring7. ------------ 1 Seal8. ------------ 1 Seal, Piston Ring9. ------------ 1 Seal, Wiper Rod10. ------------ 1 Wear Ring11. ------------ 1 Wear Ring12. 02208000 1 Locknut13. ------------ 1 Seal14. 02977121 1 Seal Kit (items 6,7,8,9,10,11 & 13)

Mar. 2001to

Current

CURB LIFT CYLINDERP/N 0693400A

S/N SWB5-10001S/N SWB6-10001


123123

123123

123123123

12312312312

12

12

123456789012345678901234567890121234567890123456789012345678901212345123456789012345678901234567890121234567890123456789012345678901212345123456789012345678901234567890121234567890123456789012345678901212345123456789012345678901234567890121234567890123456789012345678901212345

123456789012345678901234567890121234567890123456789012345678901212345123456789012345678901234567890121234567890123456789012345678901212345123456789012345678901234567890121234567890123456789012345678901212345

12341234

12341234

1212

1212

1

3

8

10 2

129713

Piston pressed onw/ Loctite 271 or equivalent

11 5 64

123451234512345123451234512345

Hose Port

3/64" PortRestriction

1234123412341234

Hose Port

3/64" PortRestriction



Mar. 2001to

Current

KNIFE DRIVE ASY5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001


1

2

3

123456123456123456123456123456123456

12345671234567123456712345671234567

55

6

© 2004 Alamo Group Inc. Parts Section -25SWB 5 & 6 (Archive Book) 01/04


02974300 - Knife Drive Asy (w/ Items 2 thru 5)1 02974311 1 Flywheel2 02974315 1 Adapter Hub3 02974317 1 Knife Drive Stud Asy4 02977820 2 * Socket Head Bolt5 02980453 1 Support6 02967570 2 Bolts

Mar. 2001to

Current

KNIFE DRIVE ASY5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001


NOTE *: Item # 5 bolts torque to 35 ft. lbs.



Mar. 2001to

Current

S/N SWB5-10001S/N SWB6-10001


SHOE - DRIVE& BREAKAWAY ASY

5 & 6 Foot

2423

27

9,14

6,7,158

13

Lube Release Pin withGrease After Assembly

Breakaway Pivot Mount ofWeldment (#27) Shown Only

19

5

20

1

20 120 1

1927

See Detailabove #27

Item # 1 (3/4" Nuts) are used forShipping Only and removed whenCutter Bar is installed

33

16

217

1

1126

93

2125

3

18,22

12

3



Mar. 2001to

Current


02975194 - Shoe, Drive & Breakaway Asy.

1 00000200 5 Nut

2 00001200 1 Nut

3 00001800 10 Nut

5 00002701 2 Flatwasher


7 00015800 2 Nut

8 5C8130 1 Nut

9 000206 3 Red Lubricap

11 02974343 2 Short Spacer Tube

12 00749130 2 Bolt

13 02974344 1 Skid Shoe Sole

14 00752670 1 Grease Fitting

15 00753642 2 Bolt

16 02974354 1 Cutter Bar Spacer

17 02974358 1 Deflector Red

18 02042300 2 Straight Adapter

19 02931300 3 Bolt

20 02972570 3 Lockwasher

21 02974300 1 Knife Drive Asy

22 02974301 1 Motor

23 02976853 4 Plow Bolt (2-1/2" Long)

24 02976854 4 Plow Bolt (7" Long)

25 02974313 1 Hydraulic Motor Adapter Bracket

26 02974342 2 Long Spacer Tube

27 02975986 1 Break-a-way Pre-asy

SHOE - DRIVE& BREAKAWAY ASY

5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001




Mar. 2001to

Current

BREAK-A-WAY ASY5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001


2

3

4

5

66

78

1

DANGER ! : DO NOT REMOVEThis Assembly is Spring Loadedat Factory and MUST NOT bedis-assembled before SpringTension is released !

7,9,12

10

11




02975986 - Breakaway Pre-asy, ( w/ Items 1 thru 12)1 02974339 1 Skid Shoe Weldment2 00011100 1 Flatwasher3 03101646 1 Lockwasher4 00002000 1 Bolt5 03200250 1 Rubber Bumper Pad6 02974363 6 Washer7 00019600 3 Lockwasher8 00607900 1 Bolt9 02975217 1 Spring Tension Block10 02974333 1 Breakaway Pivot & Spring Weldment11 0113900 1 Release Pin12 00750959 2 Bolt (Not Shown)

NOTE: DANGER ! This item is spring loaded at the factory and is displayeddis-assembled only to show components, All parts listed are available forindividual sales as replacement parts. DO NOT attempt to remove any Boltsot to remove any parts from this assembly before tension is released onspring, See Spring tension procedure in Back of BookBreakaway Pre-Assembly includes Pin & Spring already assembled in Break-a-way weldment from Factory and it is recommended that this is the wayit should be purchased for replacement as a pre-Assembled compo-nent. Item # 10 is manufactured w/ Spring installed, Spring alone cannot bereplaced without replaceing Breakaway pivot weldment.

Mar. 2001to

Current

BREAK-A-WAY ASY5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001




Mar. 2001to

Current

COMMON COMPONENTBOX

5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001


7

8

9

313

12

211

10

6


Mar. 2001to

Current

Item Part No. Qty Desription

02974368 - Common Component Box

1 00725746 1 Spanish Translation, Decal(Not Shown Attach To Tractor)

2 02964028 1 Push Pull Switch

3 02964063 1 Knob, Switch

4 02965093 1 Proper Engine, Decal(Not Shown-Attach To Tractor)

5 02970354 1 Knife Clearance, Decal(Not Shown-Attach To Tractor)

6 02974310 1 Filter Element

7 02974318 1 Wire Harness

8 02974321 1 Valve Operation Decal (Not Shown)

9 02974322 1 Reversing Switch

10 02974348 1 Tank Assembly

11 02974364 1 Valve Assembly

12 02974962 1 Switch Boot

13 02975270 1 Bar Reversing Instruction Decal

14 0410300 1 Warning Sign Decal (Not Shown-Attach To Tractor)

COMMON COMPONENTBOX

5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001




Mar. 2001to

Current

HYDRAULIC TANK ASY5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001


10

13

5

15

2520

18

23

12

12

22

2

17

4

2424

11

14

6

33 3

7

19

1

16

- " P " Port

- " T " Port


Mar. 2001to

Current

Item Part No Qty Description

02974348 - Hydraulic Tank Asy

1 00017000 8 Lockwasher2 001891 1 Elbow Adapter3 00696800 3 Straight Adapter4 10121000 2 Bolt5 0117100 1 Magentic Drain Plug6 02959924 2 Nut7 02962213 1 Elbow Adapter10 02968880 1 Sight /Temperature Guage*11 02974305 1 Solenoid Control Valve12 02974309 1 Filter Housing Asy13 02974312 1 Suction Strainer14 02974320 1 Hose15 02974366 1 Hydraulic Tank Weldment16 02974369 1 Tank Access Cover17 02974370 1 Elbow Tee Adapter18 064600D 1 Cover Gasket19 10058000 8 Bolt20 10074000 2 Bolt22 000752 1 Elbow Adapter23 02976123 2 Seal Washer24 00011700 2 Lockwasher25 02976124 8 Threaded Insert26 02976125 2 Threaded Insert

*Note: Item 10 sight gauge was moved to the other side of oil tank in July 2003and will not be visible from left side of tank as shown. Sight gauge left on leftside in drawing for illustration only.

HYDRAULIC TANK ASY5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001




Mar. 2001to

Current

HYDRAULIC PUMP ASYDisplacement

1.16 / 0.49 Cu in / Rev.5 & 6 Foot Model

S/N SWB5-10001S/N SWB6-10001


** 5-3/16" Long

Demension For Identification

3

5

11

2

4

813

610

1

1279

*

**



Mar. 2001to

Current



S/N SWB5-10001S/N SWB6-10001



02974302 1 Pump Assembly

1 02976923 1 Connecting Shaft2 02976922 1 Gear Set3 02976921 1 Gear Set4 02976920 1 End Cap5 02976919 1 Mounting Flange6 02976918 1 Gear Housing7 02976917 1 Gear Housing8 02976916 4 Housing Tie Bolt9 02976915 2 Dowel Pin10 02976914 2 Dowel Pin11 02976913 1 Mid Spacer Plate12 02976912 4 Thrust Block13 02976911 4 Flatwasher* 02976924 Ref Seal Kit (Includes Items With *)

NOTE **: Always Measure Lenth of Gear Housings (item #6 & #7)which is length of both plus Spacer Plate (item # 11) before order-ing Pump Parts, This is because there are 2 pumps with differentdisplacement, which pump depends on which model tractor isbeing used.



Mar. 2001to

Current



S/N SWB5-10001S/N SWB6-10001


** 4-7/8" Long

Demension For Identification

3

5

11

2

4

813

610

1

1279

*

**



Mar. 2001to

Current



S/N SWB5-10001S/N SWB6-10001



02974303 1 Pump Assembly

1 02976923 1 Connecting Shaft2 02976929 1 Gear Set3 02976928 1 Gear Set4 02976920 1 End Cap5 02976919 1 Mounting Flange6 02976927 1 Gear Housing7 02976926 1 Gear Housing8 02976925 4 Housing Tie Bolt9 02976915 2 Dowel Pin10 02976914 2 Dowel Pin11 02976913 1 Mid Spacer Plate12 02976912 4 Thrust Block13 02976911 4 Flatwasher* 02976924 Ref Seal Kit (Includes Items With *)

NOTE **: Always Measure Lenth of Gear Housings (item #6 & #7)which is length of both plus Spacer Plate (item # 11) before order-ing Pump Parts, This is because there are 2 pumps with differentdisplacement, which pump depends on which model tractor isbeing used. There is a special Pump # 02976844 which is thesame as above pump but it is assembled different to turn CWinstead of the standard CCW as # 02974303 does. See Instruc-tion Sheet # 02976962 on the assembly of special pump. Alsothis special Pump is rare as it was only used on one model (JohnDeere 4500, 4600, 4700) Tractor



14

14

14

14

14

14

14

4

5

6 7 8

13

109

111

2

12

3

Mar. 2001to

Current

MOTOR ASY5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001




Mar. 2001to

Current

MOTOR ASY5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001



02974301 - Hydraulic Motor

1 02976883 1 Internal Drive Shaft2 02976884 1 Star and Housing Set3 02976885 7 Housing Tie Screw4 02976886 4 Flange Attachment Screw5 02976887 1 Mount Flange6 02976888 1 Thrust Bearing Race7 02976889 1 Thrust Bearing8 02976890 1 Output Shaft9 02976891 1 Motor Housing10 02976892 1 Plug11 02976893 1 Spacer Plate12 02976894 1 End Cap13 MA000229 1 Key14 02976895 Ref Seal Kit

NOTE: Some parts are only available as prt of the seal kit.



Mar. 2001to

Current

CONTROL VALVE ASYManual Valve

5 & 6 Foot Model

S/N SWB5-10001S/N SWB6-10001


35

InOut

A

B

C

D

BYD

1

2 56

7

9

UPPER CROSS SECTION VIEW

LOWER CROSS SECTION VIEW

17,18,19

Torque to30 - 35 ft lbs.(40.7 - 47.5 NM)

-- At Least 1 Shim Must Be Used

22

13 14Apply Thread Locking Compound ToObtain Break-a-way Torque 60 in. lbs. (6.8 NM)

Torque to 21 - 24 ft. lbs. (28.5 - 32.5 NM)

20 233 1011

34

4 15 1225

28

29

16318 21

2627 33

3230

Torque to30 - 35 ft lbs.(40.7 - 47.5 NM)

Breather Must Not BePlugged With Paint

Torque to 20 - 25 ft. lbs(27.1 - 33.9 NM)

Coat Detent Parts With Grease

Torque to 10 - 12 ft.lbs. (13.6 - 16.3 NM)

24Torque to 10 - 12 ft.lbs. (13.6 - 16.3 NM)

UPPER CROSSSECTION VIEW

LOWER CROSSSECTION VIEW


Mar. 2001to

Current

CONTROL VALVE ASYManual Valve

5 & 6 Foot Model

S/N SWB5-10001S/N SWB6-10001

toS/N SWB5-CurrentS/N SWB6-CurrentItem Part No. Qty Description

02974364 - Valve Asy1 02976934 2 Unload Plunger2 02966645 2 Poppet Asy3 02966646 1 Spacer4 02976933 2 Spool5 02966648 4 Seat Asy6 02966649 2 Plug Asy7 02966650 2 Plug Asy8 02966651 2 Bushing9 02966652 2 Spring10 02966653 1 Cap Asy11 02966654 1 Plug Asy12 02976932 1 Body13 02976931 1 Poppet14 02976930 1 Seat15 02966657 4 O-Ring16 02966658 2 Retaining Ring17 02966659 AR Washer18 02966660 AR Washer19 02966661 AR Washer20 02966662 1 Washer21 02976946 1 Cap Assy22 02976945 1 Spring23 02966669 1 Spring24 02976944 2 Cone25 02976943 1 Washer26 02976942 1 Washer27 02976941 3 Ball28 02976940 1 Spring29 02976939 1 Spring30 02976938 1 Cone31 02976937 1 Spacer32 02976936 1 Adapter Cap33 02976935 AR Washer34 02966671 2 Wiper Seal35 02976957 2 Handle Kit



Mar. 2001to

Current

WIRE HARNESSP/N 02974318

5 & 6 Foot Model

S/N SWB5-10001S/N SWB6-10001


#16 Yellow wire 4" Long

Connectors f/ wires on toggleswitch are fully insulated female1/4" wide Blade Connectors

#16 White wire4" Long

#16 Red wire 4" Long

#12 Brown wire 2" Long



Inline ATC typeFuse Holder w/ 10AMP Fuse In-stalled

4-Terminal Female Connector f/ Push-Pull Switch # 02964028 & Knob #02964063 (switch not included in wire harness) see switch above

48"

36"

102"

1-1/2"

7"

#16 Red wire 16"Long (12 volt sup-ply from Tractor)

#12 Brown 16" Long(Engine Solenoid) w/insulated butt connectors

#16 Black wire 16"Long (Ground) w/ Hookor Ring terminal f/ # 10stud

12

3

1

2

3

#16 black wire insideplug (Ground Wire)

No wire connectedto this terminal

Guide Lug (no wire con-nected to this terminal)

#16 White wireinside plug

#16 black wireinside plug(Ground Wire)

No wire connectedto this terminal

#16 Yellow wireinside plug

Guide Lug (nowire connectedto this terminal)

Connectors usesealing gaskets

Connectors usesealing gaskets

1111

111111

12121212

3 position toggle reversing switch# 02974322 & switch boot #02964962 (switch not included inwire harness)

1 23 4

123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890

1234512345

12345678901123456789011234567890112345678901

1234512345

1 2

3 4

Push Pull Switch# 02964028 w/Knob # 02964063



02974305 1 Valve Solenoid Asy1 02979345 1 Body2 02979346 1 Cartridge3 02979190 1 Bolt Kit4 02979349 1 *Solenoid5 02979186 1 Stem Tube6 02979187 1 Coil Solenoid7 02979188 1 Coil Nut

* Consists of Replacement Parts: Stem Tube, Coil Solenoid, CoilNut.

3

2 x Ø .28THRU

Date Code Stamp

1

4

6

7

5

2

SCHEMATIC

2

5

4 37

61

VALVE SOLENOID5 & 6 Foot Model

Mar. 2001to

Current

S/N SWB5-10001S/N SWB6-10001




1,2 4,20

20,21

11

12

1213

15

17

16

14

10

22

19

9

9

REMOTE CONTROLHANDLES

5 & 6 Foot Model

Mar. 2001to

Current

S/N SWB5-10001S/N SWB6-10001




1. 00015800 2 Locknut (Not Shown)2. 000354 2 Bolt (Not Shown)4. 00750940 2 Locknut9. 02971200 a/r *Cable, 40" Long

02971201 a/r *Cable, 60" Long02971202 a/r *Cable, 72" Long02971203 a/r *Cable, 102" Long

10 02974296 1 Switch Mount Weldment11. 02974299 1 Remote Control Angle Mount12. 02974323 2 Controla Asy.Single Axis13. 02964028 1 Push-Pull Switch14. 02964063 1 Knob, f/ Pussh Pull Switch15. 02974318 1 Wiring Harness16. 02974321 1 Decal, Instruction Valve & Switch17. 02974322 1 Toggle Switch. 3 position19. 02974962 1 Switch Boot, f/ toggle Switch20. 00023500 6 Flatwasher21 02733700 3 Bolt22. 02975270 1 Decal Instruction Reversing Switch

* Note: Cable length will vary with type tractor that is used.Measure Cables or refer to orginal mount kit components

list to determine which cable needed.

REMOTED CONTROLHANDLES

5 & 6 Foot Model

Mar. 2001to

Current

S/N SWB5-10001S/N SWB6-10001




7,8

7.8

6

3.518

9

10

15

Mar. 2001to

Current

REMOTED CONTROLVALVE STAND

5 & 6 Foot Model

S/N SWB5-10001S/N SWB6-10001




3. 001636 2 Bolt (Not Shown)5. 02959924 2 Locknut6. 02966687 2 Adjusting Yoke End7. 02966688 2 Clevis Pin8. 02968698 2 Cotter Pin9. 02971200 a/r *Cable, 40" Long

02971201 a/r *Cable, 60" Long02971202 a/r *Cable, 72" Long02971203 a/r *Cable, 102" Long

10 ------------- 1 Valve Stand, varies with Mount Kit18 02974364 1 Valve Asy, 2 Spool

REMOTED CONTROLVALVE STAND

5 & 6 Foot Model

Mar. 2001to

Current

S/N SWB5-10001S/N SWB6-10001


NOTE: Remote Control Valve Stand only used with remote controlOption and parts on previous page showing remote control handles.Standard model used a mechanical handle assembly shown onprevios pages. Note the same valve is used with the remote handlesor the mechanical handles. Item 10 Valve stand part number will varywith the type of Tractor clipper is mounted on.



Mar. 2001to

Current

FILTER ASY5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001


1

2

3

4

5

6


Mar. 2001to

Current

FILTER ASY5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001



02974309 - Filter Asy

1 02976906 1 Bowl2 02976907 1 Filter Condition Gauge3 02976908 1 Spring4 02974319 1 Air Breather Element5 02976909 1 Air Breather Kit6 02974310 1 Filter Element7 02976910 1 Seal Kit



Mar. 2001to

Current

DECALS5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001


4

5

786

1

2

3

12

13

149

10

15


Mar. 2001to

Current

DECALS5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001



1 02966305 1 Instruction, Universal Tractor

2 02974997 1 Name, Switch Blade

3 02965262 1 Warning, Hose Burst

4 000678 1 Instruction, Grease Fitting Iniside

5 0614600 1 Caution, Spring

6 02962765 1 Danger, Multiple Hazard

7 0614500 1 Caution, No Step

8 nfs 1 Switchblade Serial Number Plate

9 02977417 1 Instruction, Operators Manual Inside

10 00776031 1 Canister, Parts Manual

11 02974374C 1 Switch Blade Oper. Manual

12 10058000 3 Bolt

13 00017000 3 Lockwasher


15 02959924 3 Locknut



ITEM PART NO. QTY TYPE DESCRIPTION

1 02970354 1 INSTRUCT Knife Clearance2 02965093 1 INSTRUCT Proper Engine3 00725746 1 PELIGRO Spanish Translation4 0410300 1 WARNING Warning Sign5 02975270 1 INSTRUCT Bar Reversing Instruction6 02974321 1 INSTRUCT Valve Operation

Mar. 2001to

Current

DECALS5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001


123

4

5

6


Mar. 2001to

Current

DECALS5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001


P/N 02970354 P/N 02965093

P/N 02977417

P/N 02966305 P/N 02962765

P/N 02974997

P/N 00725746



Mar. 2001to

Current

DECALS5 & 6 Foot

S/N SWB5-10001S/N SWB6-10001


P/N 0410300

P/N 0614500

P/N 000678 P/N 0614600

P/N 02975270

P/N 02974321

P/N 02965262


NOTES

56

SWB 5-6 Archive Book 01/04


S/N INTRODUCTION

1. This Section is to help find and identify Mount Kits, Hyd Kits and theircomponents. DO NOT ORDER Mount Kit, Sub Frame Kit or Hyd KitNumbers as they will consist of assortment of parts that may no beneeded. Use these Mount Kit, Sub-Frame Kit and Hyd Kit numbers tobreak down component list to find parts.

2. Also listed in this section is Pump Drive componet number and whichpump (2 pump sizes) should be used on which Tractor. Check thisbefore ordering Pumps or parts for the Pump.

3. Not all components of Mount Kits, Hydraulic Kits or Sub-Frame Kithave all the parts listed in this section.

4. Some Mount Kits Do Not have intallation drawings and some do.5. Shown in Illustration is a general View of Hose Connections, The

Routing and location of Tank will vary, But the hose connectionsshould not, with the exception of the Dual Wing Mounting which willcause hose to be connected different, See the Installation drawingsfor these Dual Wing Units.

6. Importand Notice: There is a Hydraulic Pump Used on one of the JohnDeere Models that is assembled to turn CW (Pump # 02976844) whichis different than the other Pumps which are assembled to turn CCW.When replaceing this pump always make sure it is assembled with thePart going in the right direction (see Instruction Sheet # 02976962).

7. When Looking up part numbers in the Hydraulic Kit or Sub-Frame Kitalways use the Serial Number Production Date as the Bill Of MaterialEffective Date. This can be done by furnishing Customer Service Dept.with the Serial Number Prefix & Serial Number of your unit when lookingfor parts. This will be required because the Kit number should not changebut the componet numbers in it can be changed.

SWITCH BLADE 5 & 6 FootMount Kit & Hyd Kit Components

Listing by Tractor Model

57SWB 5-6 Archive Book 01/04


HOSE SCHEMATIC / SINGLE WING5 & 6 Foot

CASE - IHSee Following Pages

For Tractor Model

18

14

19

19

1613

15,20

5

10

Note; This is a general hose routing, thehose routing may vary, the hose length willvary, the tank location will vary. But the hoseconnections will still be in the same place.

21

58



CASE - IH

Model: CASE - 3220Type: Rops 2 WDBolster: Row CropTires: Front: 7.50 - 16 Rear : 14.9 - 28

Item Part No. Qty Description02974985 - Sub-Frame Kit. (w/ Items 1 Thru 5)

1. 0667800 1 Cross Frame2. 0667500 1 Sub-Frame3. 0749400 1 Sub-Frame, LH5. 02974964 1 Valve Mount Weldment

02974986 - Hydraulic Kit (w/ Items 6 Thru 20)6. 0750300 1 Driveshaft, 23.88" Long7. 02975238 1 Flex Coupler Asy.8. 0749600 1 Pulley Adapter9. 0656500 1 Pump Bracket10. 02974303 1 Pump, 0.98/0.37 CID13. 02975454 1 Hose, 46" Long (1/2")14. 001771 2 Hose, 48" Long (1/4")15. 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)16. 107559 1 Hose, 52" Long (3/8")17. 0022000 2 Hose, 66" Long (1/2")18. 02972980 2 Hose, 80" Long (1/2")19. 02975239 1 Hose, 96" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy

SWB 5-6 Foot Sub-Frame Kits & Hyd Kits



Model: CASE - 385, 395Type: Rops 2 WD & 4 WDBolster: Row Crop (2 WD)Tires: Front: 7.50 - 16 (2 WD) or 8.30 - 24R3 (4 WD)

Rear : 14.9 - 28 (2 WD or 4 WD)Note: Tractor must be equiped with Hollow Axle Pivot Pin, Tractors starting

with S/N 18000 and above.


1. 0665500 1 Main Frame2. 0665400 1 Sub-Frame3. 0685900 2 Shim, 1/16" Thick4. 0686000 1 Shim, 1/32" Thick5. 02974964 1 Valve Mount Weldment

02975250 - Hydraulic Kit (w/ Items 6 Thru 20)6. 0684600 1 Pump Shaft7. 02975188 1 Flex Coupler Asy.

701573 1 Front Coupling Asy8. 0684500 1 Adapter Plate9. 0656500 1 Pump Bracket10. 02974302 1 Pump, 1.16/0.49 CID13. 02975454 1 Hose, 46" Long (1/2")14. 001771 2 Hose, 48" Long (1/4")15. 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)16. 107559 1 Hose, 52" Long (3/8")18. 02972980 2 Hose, 80" Long (1/2")19. 02975239 1 Hose, 96" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy

SWB 5-6 Foot Sub-Frame Kits & Hyd KitsCASE - IH

60




Model: CASE - 485, 495Type: Rops 2 WD & 4 WDBolster: Row CropTires: Front: 7.50 - 16 (2 WD) & 8.30 - 24R3 (4 WD)

Rear : 14.9 - 28 (2 WD or 4 WD)Note: Tractor must be equiped with Hollow Axle Pivot Pin, Tractors starting




02974988 - Hydraulic Kit (w/ Items 6 Thru 20)6. 0662200 1 Pump Shaft7. 02975188 1 Flex Coupler Asy.

701573 1 Front Coupling Asy8 0684500 1 Adapter Plate9. 0656500 1 Pump Bracket10. 02974302 1 Pump, 1.16/0.49 CID13. 02975454 1 Hose, 46" Long (1/2")14. 001771 2 Hose, 48" Long (1/4")15. 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)16. 107559 1 Hose, 52" Long (3/8")18. 02972980 2 Hose, 80" Long (1/2")19. 02975239 1 Hose, 96" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy




Model: CASE - 585, 685, 595, 695Type: Rops 2 WDBolster: Row CropTires: Front: 10.00 - 16 (2 WD) Rear : 16.9 - 34 (2 WD)Note: Tractor must be equiped with Hollow Axle Pivot Pin, Tractors starting




02975997 - Hydraulic Kit (w/ Items 6 Thru 20)6. 0662200 1 Pump Shaft7. 02975188 1 Flex Coupler Asy.8. 701573 1 Front Coupling Asy9. 0656500 1 Pump Bracket10. 02974302 1 Pump, 1.16/0.49 CID13. 02975454 1 Hose, 46" Long (1/2")14. 001771 2 Hose, 48" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)16. 107559 1 Hose, 52" Long (3/8")18. 02890700 2 Hose, 90" Long (1/2")19 02975239 1 Hose, 96" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy

62



Model: CASE - C50, C60Type: Rops 2 WDBolster: Row CropTires: Front: 10.00 - 16 (2 WD)

Rear : 16.9 - 34 (2 WD)


1. 0758200 1 Main Frame2. 0758600 1 Sub-Frame4. 02977326 1 Installation Drawing5. 02977323 1 Valve Mount Weldment

02977318 - Hydraulic Kit (w/ Items 6 Thru 20)6. 0756000 1 Pump Shaft, 22-3/4" Long7. 0148600 1 Key8. 0752200 1 Pulley Adapter, 7/8" X 13 Spline

02975188 1 Coupling Asy, Flex9. 0656500 1 Pump Bracket10. 02974302 1 Pump, 1.16/0.49 CID11. 02977327 1 Installation Drawing13. 02975454 1 Hose, 46" Long (1/2")14. 00756811 2 Hose, 70" Long (1/4")15. 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)16. 107559 1 Hose, 52" Long (3/8")18. 02972980 2 Hose, 80" Long (1/2")19. 02975239 1 Hose, 96" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy




HOSE SCHEMATIC / SINGLEWING

5 & 6 FootFORD - NH

See Following PagesFor Tractor Model

18

14

19

19

1613

15,20

5

10


21

64



SWB 5-6 Foot Sub-Frame Kits & Hyd KitsFORD - NEW HOLLAND

Model: Ford - 335, 340, 540, 2000, 2600, 3000, 3100,3400, 3600, 4000SU, 4100SU, 4600SU

Type: Rops 2 WDTires: Front: 7.50 - 16 (2 WD) Rear : 14.9 - 28 (2 WD)


2. 0586100 1 Sub-Frame3. 0486500 2 Spacer4. 02978351 1 Installation Drawing5. 02974977 1 Valve Mount Weldment

02974984 - Hydraulic Kit (w/ Items 6 Thru 20)6. 0419500 1 Pump Shaft

0148600 1 Key7. 0429400 1 Pulley Adapter Asy.8. 02975188 1 Coupling Asy, Flex9. 0335700 1 Pump Bracket10. 02974302 1 Pump, 1.16/0.49 CID11. 02978352 1 Installation Drawing13. 02975454 1 Hose, 46" Long (1/2")14. 001771 2 Hose, 48" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02972980 2 Hose, 80" Long (1/2")19 02975239 2 Hose, 96" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy



Model: Ford - 2310, 2610, 2810, 2910, 3910, 3610, 4610SU

Type: Rops 2 WD

Tires: Front: 7.50 - 16 (2 WD) Rear : 14.9 - 28 (2 WD)Note: Tank Blocks Tractor Lights: Relocate Lights if required, using

Ford P/N 310068 & EONN13A097AA For Side Hood Mounting


2. 0647000 1 Sub-Frame3. 036310D 1 Spacer4. 02977956 1 Installation Drawing5. 02974977 1 Valve Mount Weldment




66




Model: Ford - 250C, 260C, 340A, 340B, 445, 545, 540A,3230, 3430, 3930

Type: Rops 2 WDTires: Front: 7.50 - 16 (2 WD) Rear : 14.9 - 28 (2 WD)Notel: Tank Blocks Tractor Lights: Relocate Lights if required, using

Ford P/N 310068 & EoNN13A097AA For Side Hood Mounting


2. 0647000 1 Sub-Frame3. 036310D 1 Spacer4. 02977956 1 Installation Drawing5. 02974977 1 Valve Mount Weldment





Model: Ford - 4610, 4630Type: Rops 2 WD & 4 WDTires: Front: 7.50 - 18 (2 WD) 11.2 - 24 (4 WD)

Rear : 16.9 - 30 (2 WD) 9.5 - 24 (4 WD)


2. 0655900 1 Sub-Frame3. 0635200 1 Sub-Frame4. 02977330 1 Installation Drawing5. 02974977 1 Valve Mount Weldment



FORD - NEW HOLLANDSWB 5-6 Foot Sub-Frame Kits & Hyd Kits

68



Model: Ford - 4610, 4630Type: Cab 2 WD & 4 WDTires: Front: 7.50 - 18 (2 WD) 11.2 - 24 (4 WD)

Rear : 14.9 - 28 (2 WD) 16.9 - 30 (4 WD)Note: Tank Blocks Tractor Lights: Relocate Lights if required, using

Ford P/N 310068 & EONN13A097AA For Side Hood Mounting


1. 0672900 1 Main Frame2. 0665400 1 Sub-Frame4. 02978030 1 Installation Drawing5. 02978032 1 Valve Mount Weldment


0148600 1 Key7. 0429400 1 Pulley Adapter Asy.8. 02975188 1 Coupling Asy, Flex9. 0336600 1 Pump Bracket10. 02974302 1 Pump, 1.16/0.49 CID11. 02978031 1 Installation Drawing (Hyd Kit)

02975200 1 Installation Drawing (Remote Control Asy)13. 02970870 1 Hose, 20" Long (1/2")14. 00763741 1 Hose, 36" Long (1/4")

02964451 1 Hose, 43" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02858800 2 Hose, 102" Long (1/2")19 02966148 2 Hose, 76" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy





Model: Ford - 5635Type: Cab 2 WDTires: Front: 10.00 - 16 (2 WD)

Rear : 16.9 - 30 (2 WD)Item Part No. Qty Description

02974980 - Sub-Frame Kit. (w/ Items 1 Thru 3)1. 0742100 1 Main-Frame2. 0725900 1 Sub-Frame3. 0741400 1 Spacer


0743600 1 Pump Drive Adapter0148600 1 Key

7. 0429400 1 Pulley Adapter Asy.8. 02975188 1 Coupling Asy, Flex9. 0742500 1 Pump Mount Weldment10. 02974302 1 Pump, 1.16/0.49 CID11. 02975200 1 Installation Drawing13. 02965454 1 Hose, 46" Long (1/2")14. 001978 1 Hose, 69" Long (1/4")

001977 1 Hose, 76" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02972980 2 Hose, 80" Long (1/2")19 02275900 1 Hose, 35" Long (3/8")

03200277 1 Hose, 72" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy

70



Model: Ford - TN55,65,70 & 75 Series (Single Wing)Type: Rops 2 WD & 4 WD (Single Wing RH)Tires: Front: 7.50 - 18 (2 WD) 11.2 - 24 (4 WD)

Rear : 16.9 - 30 (2 WD & 4 WD)


1. 02976275 1 Main-Frame2. 0665400 1 Sub-Frame4. 02977332 1 Installation Drawing5. 02977678 1 Saddle Mount Weldment

02977321 - Hydraulic Kit (w/ Items 6 Thru 20)6. 02976279 1 Pump Shaft, 25.25" Long

0148600 1 Key7. 02975110 1 Pulley Adapter, Machined8. 02975188 1 Coupling Asy, Flex9. 02976283 1 Pump Mount, Machined10. 02974303 1 Pump, 0.98/0.37 CID11. 02977333 1 Installation Drawing13. 02977224 1 Hose, 62" Long (1/2")14. 00756811 2 Hose, 70" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02972980 2 Hose, 80" Long (1/2")19 107559 1 Hose, 52" Long (3/8")

02975239 1 Hose, 96" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy22. 02977682 - Pump Guard Kit (optional equipment)23. 0487100 -- Knife Brackets (optional equipment)24. 02979512 -- Canopy Cage Kit (optional equipment)25. 02979481 -- Rear Screen Kit (optional equipment)26. 02979502 -- Aluminum Canopy (optional equipment)




Model: Ford - TN55, 65, 70 & 75 Series (Dual Wings)Type: Rops 2 WD (Dual Wing RH & LH)Special: Illustration for Single Wing in This Book Will Not work for this.Tires: Front: 7.50 - 18 (2 WD)

Rear : 16.9 - 30 (2 WD)


1. 02978012 1 Main-Frame2. 02978001 1 Plate, RH Front Mount

02978002 1 Plate, LH Front Mount4. 02978031 1 Installation Drawing5. 02977660 1 Tank Mount Weldment

02978027 1 Tank Mount Weldment, Dual Wing02978068 - Hydraulic Kit (w/ Items 6 Thru 20)

6. 02976279 1 Pump Shaft, 25.25" Long0148600 1 Key

7. 02975110 1 Pulley Adapter, Machined8. 02975188 1 Coupling Asy, Flex9. 02976283 1 Pump Mount, Machined10. 02974303 1 Pump, 0.98/0.37 CID11. 02978062 1 Installation Drawing, (Hyd Kit)

02978141 1 Installation Drawing, (Wiring Harness)02975133 1 Installation Drawing, (Crankshaft Pulley Adapter)

13. 02977224 1 Hose, 62" Long (1/2")14. 02045800 2 Hose, 53" Long (1/4")

001845 2 Hose, 70" Long (1/4")03200291 2 Hose, 100" Long (1/4")

15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 03200804 2 Hose, 39" Long (1/2")


19 107559 1 Hose, 52" Long (3/8")02975239 1 Hose, 96" Long (3/8")

20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy22. 02977682 - Pump Guard Kit (optional Equipment)


72



Model: Ford - TN 55D, 65D, 70D & 75D Series (Single Wing)Type: Cab 2 WDTires: Front: 9.5L - 15 (2 WD)

Rear : 16.9 - 28 (2 WD)


2. 02978056 1 Sub-Frame4. 02978054 1 Installation Drawing5. 02975125 1 Axle Mount Strap


0148600 1 Key7. 02975110 1 Pulley Adapter, Machined8. 02975188 1 Coupling Asy, Flex9. 02976283 1 Pump Mount, Machined10. 02974303 1 Pump, 0.98/0.37 CID11. 02978055 1 Installation Drawing, (Hyd Kit)

02975200 1 Installation Drawing, (Remote Control)02975133 1 Installation Drawing, (Crankshaft Pulley Adapter)

13. 02977224 1 Hose, 62" Long (1/2")14. 02839000 2 Hose, 64" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02890700 2 Hose, 90" Long (1/2")19 02974439 1 Hose, 40" Long (3/8")

03200851 1 Hose, 62" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy22. 02977682 1 Pump Guard (Optional)23. 0487100 & 02980026 1 Knife Brackets (Optional), qty 1 / each




Model: Ford - TN 55D, 65D, 70D & 75D Series (Single Wing)Type: Cab 4 WDTires: Front: 9.5 - 20 (4 WD)

Rear : 13.6 - 28 (4 WD)


2. 02980079 1 Sub-Frame5. 02975125 1 Axle Mount Strap



02975133 1 Installation Drawing, (Crankshaft Pulley Adapter)13. 02980088 1 Hose, 80" Long (1/4")14. 001979 1 Hose, 72" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02961852 1 Hose, 72" Long (1/2")19 02980090 1 Hose, 69" Long (3/8")

02890700 2 Hose, 90" Long (1/2")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02977674 1 Control Stand Weldment22. 02980078 1 Valve Mount Weldment23. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy24. 02977682 1 Pump Guard (Optional)25. 0487100 & 02980026 1 Knife Brackets (Optional), qty 1 / each


74



Model: Ford - TN 55D, 65D, 72D & 75D Series w/ LoaderType: Cab 4 WD w/ Front End LoaderSpecial: This Kit is designed to fit w/ NH "32LA" Loader. The Tank is mounted

on the RH side of Cab. The RH Door NOT accessible as entry or exit.Tires: Front: 11.2 - 24 (4 WD) Rear : 16.9 - 28 (4 WD)


2. 02979015 1 Sub-Frame3 02979100 1 Spacer, 1"4. 02979059 1 Installation Drawing5. 02975125 1 Axle Mount Strap



02975200 1 Installation Drawing, (Remote Control)02975133 1 Installation Drawing, (Crankshaft Pulley Adapter)

13. 02972423 1 Hose, 112" Long (1/2")14. 03200287 2 Hose, 58" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02041700 2 Hose, 53" Long (1/2")19 02275900 1 Hose, 35" Long (3/8")

02965101 1 Hose, 105" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy22. 02977682 1 Pump Guard (Optional)23. 0487100 & 02980026 1 Knife Brackets (Optional), qty 1 / each




Model: Ford - TL 80 / 90 / 100 Series w/ Single WingType: Cab 2 WD & 4 WD w/ Single WingSpecial: SINGLE WING ONLYTires: Front: 11.2 - 24 (R-1) (4 WD) Rear : 16.9 - 30 (R-1) (4 WD)


1 02977630 1 Main Frame2. 0725900 1 Sub-Frame3 02977608 1 Plate, Front Mount

02977609 1 Plate, Side Mount02977610 1 Plate Spacer

4. 02977694 1 Installation Drawing5. 02975125 1 Saddle Mount Weldment, RH

02977660 1 Tank Mount Wldment02977680 - Hydraulic Kit (w/ Items 6 Thru 20)

6. 02977633 1 Pump Drive Shaft0148600 1 Key

7. 02975110 1 Pulley Adapter, Machined02977632 1 Plate, Crank Shaft Adapter

8. 02975188 1 Coupling Asy, Flex9. 02977652 1 Pump Mount, Machined

00774909 4 Spacer, To Raise Battery Mount10. 02974303 1 Pump, 0.98/0.37 CID11. 02977695 1 Installation Drawing, (Hyd Kit)

02975200 1 Installation Drawing, (Remote Control)13. 02977224 1 Hose, 62" Long (1/2")14. 00756811 2 Hose, 70" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 00757224 2 Hose, 106" Long (1/2")19 107559 1 Hose, 52" Long (3/8")



76




Model: Ford - TL 80 / 90 / 100 Series w/ Single WingType: ROPS 2 WD & 4 WD (w/ Single Wing RH)Special: SINGLE WING ONLYTires: Front: 11.2 - 24 (R-1) (4 WD) Rear : 16.9 - 30 (R-1) (4 WD)


1 02980183 1 Sub-Frame Weldment2. 0725900 1 Sub-Frame Weldment3 02977608 1 Plate, Front Mount

02977609 1 Plate, Side Mount02977610 1 Plate Spacer

4. 0112400 4 Stop Pin5. 02977870 1 Saddle Mount Weldment, RH

02977660 1 Tank Mount Wldment02980165 - Hydraulic Kit (w/ Items 6 Thru 23)


7. 02980013 1 Pulley Adapter, Machined8. 02975188 1 Coupling Asy, Flex9. 02977652 1 Pump Mount, Machined

00774909 4 Spacer, To Raise Battery Mount10. 02974303 1 Pump, 0.98/0.37 CID13. 02965454 1 Hose, 48" Long (1/2")14. 02980166 1 Hose, 66" Long (1/2")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02980167 1 Hose, 115" Long (1/2")19. 00758811 2 Hose, 70" Long (1/4")20. 00757224 2 Hose, 106" Long (1/2")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02977335 1 Valve Mount Bracket Weldment22. 107352 1 Control Stand Weldment23. 02979318 1 Plate, Belt Cover24. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy



Model: Ford - TL80 / 90 / 100 Series (Dual Wings)Type: Cab 2 WD & 4 WD (Dual Wing RH & LH)Special: Illustration for Single Wing in This Book Will Not work for this.Tires: Front: 7.50 - 18 (2 WD) 11.2 - 24 (4 WD)

Rear : 16.9 - 30 (2 WD) 16.9 - 30 (4 WD)


1. 02977630 1 Main-Frame, RH02977835 1 Main-Frame, LH

2. 0748700 1 Sub-Frame, RH0748700 1 Sub-Frame, LH

3. 02977608 1 Plate, Front Mount, RH02977829 1 Plate, Front Mount, LH02977609 1 Plate, Side Mount02977610 1 Plate, Spacer

4. 02977917 1 Installation Drawing5. 02977660 1 Tank Mount Weldment

02977871 1 Dual Wing Saddle Mount Weldment02977926 - Hydraulic Kit (w/ Items 6 Thru 20)


7. 02975110 1 Pulley Adapter, Machined02977632 1 Plate, Crank Shaft Adapter

8. 02975188 1 Coupling Asy, Flex9. 02977652 1 Pump Mount, Machined10. 02974303 1 Pump, .098/0.37 CID

00774909 4 Spacer, To Raise Battery11. 02977918 1 Installation Drawing, (Hyd Kit)

02978141 1 Installation Drawing, (Wiring Harness)02975200 1 Installation drawing, (Remote Control)02975133 1 Installation Drawing, (Crankshaft Pulley Adapter)

13. 03200804 1 Hose, 39" Long (1/2")14. 02045800 2 Hose, 53" Long (1/4")


15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 03200804 2 Hose, 39" Long (1/2")


19 107559 1 Hose, 52" Long (3/8")02975239 1 Hose, 96" Long (3/8")

20. 0741300 2 Hose Clamp (for Hose # 01500321)02977681 - Pump Guard Kit (optional Equipment)

21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy


78



Model: Ford - TS SeriesType: Cab 2 WD & 4 WDSpecial: This Kit includes Battery Relocation Instructions, This relocation does

not work on Tractors with 24 X 24 Transmissions, in such case Dealer/Customer will be responsible for Modifications.

Tires: Front: 7.50 - 18 (2 WD) 11.2 - 24 (4 WD)Rear : 16.9 - 30 (2 WD & 4 WD)


1. 02977843 1 Frame Rail, Front02977842 1 Rail Weldment

2. 0665400 1 Sub-Frame4. 02978139 1 Installation Drawing5. 02943100 1 Axle Mount Strap

02978074 - Hydraulic Kit (w/ Items 6 Thru 20)6. 02977731 1 Pump Shaft, 24" Long

02702900 1 Hub0148600 1 Key

7. 02966404 1 Machined Spacer8. 02975188 1 Coupling Asy, Flex9. 02977845 1 Pump Mount, Machined10. 02974302 1 Pump, 1.16/0.49 CID11. 02978140 1 Installation Drawing, (Hyd Kit)

02975200 1 Installation Drawing, (Remote Control)803455 1 Installation Drawing, (Bracket Modification)

13. 02977224 1 Hose, 62" Long (1/2")14. 00756811 2 Hose, 70" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 00757224 2 Hose, 106" Long (1/2")19 107559 1 Hose, 52" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy




HOSE SCHEMATIC / SINGLEWING

5 & 6 FootJOHN DEERESee Following Pages

For Tractor Model

18

14

19

19

1613

15,20

5

10


21

80



Model: John Deere - 4500, 4600, 4700Type: Rops 4 WDSpecial: Tractor must be eqipped with Mid-Mount PTO in order to operate the

Switch Blade, (Not included in Mount Kit), If required order JD P/N 19590 and install according to Instructions supplied with Kit.

Tires: Front: 7.50 - 18 (2 WD) 11.2 - 24 (4 WD)Rear : 16.9 - 30 (2 WD & 4 WD)


1. 02976683 1 Switch Blade Mount Weldment2. 0665400 1 Sub-Frame4. 02976797 1 Installation Drawing5. 02976676 1 Plate, Backside Hanger

02976795 - Hydraulic Kit (w/ Items 6 Thru 20)6. 02975257A 1 Driveline Asy7. 02976848 1 Collar Shaft Spacer8. 02976692 1 Plate, Pump Coupler

02976772 1 Plate, Shaft Cover02976715 1 Plate, Tank Mount Brace

10.* 02976844 1 *Pump, 0.98/0.37 CID (CW Rotation Pump)02976962 1 *Pump Asy Instruction, (to Reverse Rotation

of the CCW Pump #02974303 to make it CW)11. 02976798 1 Installation Drawing, (Hyd Kit)13. 02963468 1 Hose, 56" Long (1/2")14. 02839000 2 Hose, 64" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02890700 2 Hose, 90" Long (1/2")19 03200276 1 Hose, 62" Long (3/8")


* Importand Notice: This Hydraulic Pump # 02976962 ONLY Usedon this Special John Deere Tractor, Pump is assembled to turn CW(Pump # 02976844) which is different than the other Pumps which areassembled to turn CCW. When replaceing this pump always makesure it is assembled with the Part going in the right direction (seeInstruction Sheet 02976962). The Parts are the same as the #02974303Pump BUT ARE ASSEMBLED COMPLETLY DIFFERENT. There areNOT MANY of these Pumps Used.

JOHN DEERESWB 5-6 Foot Sub-Frame Kits & Hyd Kits



Model: John Deere - 5200, 5300, 5400Type: Rops 2 WD & 4 WDTires: Front: 7.50 - 16 (2 WD) 11.2 - 24 (4 WD)

Rear : 16.9 - 30 (2 WD & 4 WD)


2. 0690400 1 Sub-Frame Asy0689900 1 Sub-Frame w/ Extended Lugs

4. 02977328 1 Installation Drawing5. 02975253 1 Valve Mount Weldment

02977322 - Hydraulic Kit (w/ Items 6 Thru 20)6. 0690800 1 Pump Drive Shaft

0148600 1 Key7. 02975188 1 Coupler Asy, Flex8. 0429400 1 Pulley Adapter Asy

0745500 1 Plate, Pulley Adapter9. 0670300 1 Pump & Tank Mounting Bracket10. 02974303 1 Pump, 0.98/0.37 CID (CCW Rotation Pump)11. 02977334 1 Installation Drawing, (Hyd Kit)13. 02970870 1 Hose, 20" Long (1/2")14. 00756811 2 Hose, 70" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02972980 2 Hose, 80" Long (1/2")19 02966148 1 Hose, 76" Long (3/8")


SWB 5-6 Foot Sub-Frame Kits & Hyd KitsJOHN DEERE

82




Model: John Deere - 5210, 5310, 5410Type: Rops 2 WD & 4 WDTires: Front: 7.50 - 16 (2 WD) 11.2 - 24 (4 WD)

Rear : 16.9 - 30 (2 WD & 4 WD)






0754700 1 Pulley Adapter9. 0754200 1 Pump & Tank Mount Bracket10. 02974303 1 Pump, 0.98/0.37 CID (CCW Rotation Pump)11. 02977329 1 Installation Drawing, (Hyd Kit)13. 02970870 1 Hose, 20" Long (1/2")14. 02839000 2 Hose, 64" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02972980 2 Hose, 80" Long (1/2")19 02975239 2 Hose, 96" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy




Model: John Deere - 5210, 5310, 5410Type: Cab 2 WD & 4 WDTires: Front: 7.50 - 16 (2 WD) 11.2 - 24 (4 WD)

Rear : 16.9 - 30 (2 WD & 4 WD)


1 0737200 1 Main-Frame4. 02977930 1 Installation Drawing



0754700 1 Pulley Adapter9. 0754200 1 Pump & Tank Mount Bracket10. 02974303 1 Pump, 0.98/0.37 CID (CCW Rotation Pump)11. 02977931 1 Installation Drawing, (Hyd Kit)

02975200 1 Installation Drawing, (Remote Control)13. 02970870 1 Hose, 20" Long (1/2")14. 02890900 2 Hose, 47" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02890700 2 Hose, 90" Long (1/2")19 107559 1 Hose, 52" Long (3/8")


84



SWB 5-6 Foot Sub-Frame Kits & Hyd KitsJOHN DEEREModel: John Deere - 5220, 5320Type: Rops 2 WD w/ Straddle Mount PlatformTires: Front: 7.50 - 16 (2 WD)

Rear : 16.9 - 30 (2 WD)Note: This mount kit has been designed to fit tractors with a "Straddle mount opera-

tor station". Dealer / Customer responsible for any required modifications formounting tractors equiped w/ an "Isolated open operators station (IOOS)" (ieflat platform). Thw RH Steps must be removed for lift carraige clearence,entrance / exit on rh side blocked by control stand. Mid mounted valves onsome tarctors may have to be moved to allow clearence.






0754700 1 Pulley Adapter9. 0754200 1 Pump & Tank Mount Bracket10. 02974303 1 Pump, 0.98/0.37 CID (CCW Rotation Pump)11. 02977329 1 Installation Drawing, (Hyd Kit)13. 02970870 1 Hose, 20" Long (1/2")14. 02839000 2 Hose, 64" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02972980 2 Hose, 80" Long (1/2")19 02975239 2 Hose, 96" Long (3/8")20. 0741300 2 Hose Clamp (for Hose # 01500321)21. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy22. 02979943 -- Aluminum Canopy (Straddle Platform only)



Model: John Deere - 6200, 6300, 6400Type: Rops 2 WDTires: Front: 10.00 - 16 (2 WD)

Rear : 16.9 - 30 (2 WD)


1 0734000 1 Main-Frame2. 0665400 1 Sub-Frame



0735600 1 Plate, Pulley Adapter9. 0736400 1 Pump & Tank Mount Bracket10. 02974303 1 Pump, 0.98/0.37 CID (CCW Rotation Pump)13. 02965454 1 Hose, 46" Long (1/2")14. 02839000 1 Hose, 64" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)18. 02972980 2 Hose, 80" Long (1/2")19 107559 1 Hose, 52" Long (3/8")



86



HOSE SCHEMATIC / SINGLE WING5 & 6 FootKubota

See Following PagesFor Tractor Model


18

14

19

19

1613

15,20

5

10

21



Model: Kubota - L3750, L4150Type: Rops 2 WD & 4 WDSpecial: Tractor must be equipped with Kubota Pulley P/N 70765-9001-0 from

Loader Kit P/NBF900-APTires: Front: (2 WD) 8.3 - 20 (4 WD)

Rear : 13.6 - 28 (2 WD) 13.6 - 28 (4 WD)


2. 0660500 1 Sub-Frame0635200 1 Sub-Frame

3 0660100 1 Tank Bracket4. 02978406 1 Installation Drawing5. 02974964 1 Valve Mount Weldment


0148600 1 Key7. 02975188 1 Coupler Asy, Flex8. 0663200 1 Pulley Adapter9. 0664700 1 Pump Mount Bracket10. 02974302 1 Pump, 1.16/0.49 CID (CCW Rotation Pump)11. 02978407 1 Installation Drawing, (Hyd Kit)13. 02977224 1 Hose, 62" Long (1/2")14. 001771 2 Hose, 48" Long (1/4")15 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)19 02971139 1 Hose, 40" Long (3/8")


SWB 5-6 Foot Sub-Frame Kits & Hyd KitsKUBOTA

88



HOSE SCHEMATIC / SINGLE WING5 & 6 Foot

Massey FergusonSee Following Pages

For Tractor Model

18

14

19

19

1613

15,20

5

10


21



SWB 5-6 Foot Sub-Frame Kits & Hyd KitsMASSEY FERGUSON

Model: Massey Ferguson - 1433V, 1440VType: Rops 2 WD& 4 WDTires: Front: 7.50 - 16 (2 WD)

Rear : 14.9 - 24 (2 WD)


1. 02979310 1 Frame Rail Weldment2. 0112400 1 Stop Pin


0148600 1 Key4. 02975188 1 Coupler Asy, Flex5. 02975110 1 Pulley Adapter, Machined6. 02979324 1 Plate Spacer Adapter7. 02979315 1 Tank Mount Bracket Weldment8. 02974303 1 Pump, 0.98/0.37 CID (CCW Rotation Pump)9. 02979319 1 Pump Mount, Machined10. 02979329 1 Hose, 21-1/2" Long (1/2")11. 02972719 2 Hose, 66" Long (1/2")12 01500321 1 Hose, 48" Long (1") (use Clamps on Ends)13. 02966148 1 Hose, 76" Long (3/8")14. 02045800 2 Hose, 53" Long (1/4")15. 61026400 1 Hose, 42" Long (1/2")16. 0741300 2 Hose Clamp (for Hose # 01500321)17. 02979318 1 Plate, Belt Cover18. 02979325 1 Valve Stand Weldment19. 02979328 1 Plate Support20. 02974320 1 Hose, 14" Long (1/2") See Hyd Tank Asy

90



NOTES

Switch Blade Archive Book 10/02Printed U.S.A.

Switch Blade 5 ft. & 6 ft.Archive Book No. 02979443

2002 Edition

Documents

01, Front Cover - Alamo Industrial · 1. The purchase order must include the Name, Address (Ship to Street Address) of the Person / Organization ordering the parts. Who / How Parts