011-011

Embed Size (px)

Citation preview

  • 8/3/2019 011-011

    1/33

    SPECIFICATIONS

    A FIXED FOUNTAIN SYSTEM

    1.0 GENERAL

    1.1 DESCRIPTION

    A. Manufacturer shall furnish a fixed fountain aeration system capable of

    pumping water from below the surface of a body of water.

    B. A submersible motor shall draw water into an impeller housing where

    it shall be pumped into the atmosphere in the form of a decorative spray-

    type fountain.

    C. The water droplets shall become oxygen enriched and return to the

    surface, therefore transferring oxygen from the atmosphere into the body of

    water. Surface area of water body shall also be increased through constant

    wave action resulting in additional atmospheric oxygen transfer.

    D. This repeated action shall effectively mix and de-stratify the body of

    water and distribute the dissolved oxygen continuously.

    E. Fountain system shall include an oil-cooled motor sealed in a stainless

    steel housing, with shaft mounted impeller inside a discharge tube. This

    assembly shall be connected to an electrical control panel by underwater

    power cable, all of which as specified in SECTION 1.2.

    1.2 AERATOR COMPONENTS DESCRIPTION

    A. Frameworkshall be a weldment of rectangular and square Series 300

    Stainless Steel tubing with a minimum wall thickness of 1/8 inch. Pump

    support brackets (horizontal only) shall be made out of PVC, nylon, other non

    metallic material and Series 300 stainless steel to give the power/pump unit

    proper support. All fasteners shall be Series 300 Stainless Steel.

    B. Discharge Tube shall be manufactured out of PVC for proper

    diameter and shall be of proper length to insure that the discharge assembly

    and pattern are above the highest water level when the unit is running.

    C. Impeller housing shall be cast from nylon type 6 material. The

    impeller housing shall be precision machined to accept the float tube and

    capable of being bolted to the motor housing. The impeller housing shall

    house the stainless steel impeller, insert and flow straightener (if applicable).

    D. Flow Straightener shall be precision machined from nylon type 6

    material and shall have 18 curved vanes. The vanes shall take the spinning

    01/07Page 1

  • 8/3/2019 011-011

    2/33

    discharge water from the impeller and convert it to a straight, vertical flow.

    The gap between the vanes shall be at least 3/8 wide and have a total

    length not less than 2-1/2 long. It shall be factory installed for various

    optional spray patterns.

    E. Motor housing shall be Series 300 Stainless Steel. 1-5HP shall have

    a permanent Series 300 Stainless Steel electrical hub welded on the side of

    the housing to allow electrical cable entry. The 1/2HP shall have a Series 300

    Stainless Steel electrical hub welded on the bottom of the housing to allow

    electrical cable entry.

    01/07Page 2

  • 8/3/2019 011-011

    3/33

    F. Motor shall contain a Series 300 Stainless Steel shaft incorporating a

    permanent split phase capacitor run on single phase motors and a polyphase

    induction on three phase motors. The rotor shall be dynamically balanced

    and run in a ball bearing supported system. The stator windings shall be

    double dipped and baked with a Class F insulation, designed for oil

    immersion operation. The oil shall be a highly refined, mineral oil of food

    grade quality, specially formulated for lubrication. It shall meet FDA

    regulations. The oil shall provide continuous lubrication of bearings and

    internal seals and further function as an efficient heat transfer medium,

    allowing the motor to operate at 3450 RPM, at relatively low temperatures.

    The motor shall be contained in the motor housing by a Series 300 Stainless

    Steel top plate.

    G.

    Seals used to protect the motor against water or oil leakage shall be amechanical, rotating type assembly, composed of silicon carbide and Series

    300 Stainless Steel. All elastomers shall meet UL 778 requirements. This

    assembly shall then be encapsulated and protected within a Series 300

    Stainless Steel cartridge assembly.

    H. Underwater power cable shall be UL Listed and specifically

    designed for underwater use. The conductors are flexible, stranded copper

    wire sized for the amp draw and length of run. The conductors shall be

    resistant to oil, water and cracking. Power cable shall be fitted with a cablestrain relief device, located within five feet of motor housing, capable of

    being attached to the S hooks mounted on the motor housing clamp. This

    will ensure that no potential damage can occur to any cable connections, due

    to tension on the cable.

    I. Underwater power cable disconnect shall be located

    approximately three feet from the motor housing. It is a two piece molded

    assembly made of thermoplastics, meeting UL 778 requirements. The cap

    end shall be permanently connected to the underwater pin and socketconnector (see Section 1.2 Item J.). The body end of the disconnect shall be

    permanently attached to the underwater power cable and sealed with an

    approved compound. This is intended to prevent water entry if damage

    should occur to the cable. The disconnect shall be sealed with an internal o-

    ring and by an external Series 300 Stainless Steel clamp ring, which can be

    easily opened.

    01/07Page 3

  • 8/3/2019 011-011

    4/33

    J. Underwater Pin and Socket Connector (1-5HP)shall consist of a

    Series 900 IP68 pin and socket connector. It shall be of a 4 pin configuration

    rated 32 amps at 600 volts AC. The pin end shall be potted into a Series 300

    Stainless Steel 90 adapter elbow with an approved ridged epoxy. This

    assembly shall be permanently attached to the Series 300 Stainless Steel

    hub that is welded onto the side of the Series 300 Stainless Steel motor

    housing. The socket end shall be attached to a 36 piece of UL Listed

    underwater power cable. It shall be permanently secured to the UL Listed

    power cable by means of an integrated clamp and Series 300 Stainless Steel

    screws. It shall be completely epoxied to prevent entry of water or any other

    foreign matter. The other end of this assembly is permanently attached to

    the cap end of the underwater cable disconnect. It is sealed with a flexible

    potting compound.

    1/2HP shall consist of a Series 900, IP68 pin and socket connector. It shall be

    of a 4 pin configuration rated 32 amps at 600 volts AC. The pin end shall be

    potted into a Series 300 Stainless Steel straight bell-shaped adapter with an

    approved ridged epoxy. This assembly shall be permanently attached to a

    reinforced braided hose and a Series 300 Stainless Steel elbow. This shall be

    attached to a Series 300 Stainless Steel hub which is welded on the bottom

    of the motor housing. This complete assembly shall be sealed with an

    approved flexible potting compound. The socket end shall be attached to a

    36 piece of UL Listed underwater power cable. It shall be permanently

    secured to the UL Listed power cable by means of an integrated clamp and

    01/07Page 4

  • 8/3/2019 011-011

    5/33

    Series 300 Stainless Steel screws. It shall be completely epoxied to prevent

    entry of water or any other foreign matter. The other end of this assembly

    shall be permanently attached to the cap end of the underwater cable

    disconnect. It shall be sealed with an approved flexible potting compound.

    K. Fasteners and anchor connectors shall be Series 300 Stainless

    Steel.

    L. Electrical control panel specifications, see SECTION 3.

    M. Intake screen shall be made of 20 Gauge, Series 300 Stainless Steel.

    The screen shall have a minimum of 58% open area, representing 91 square

    inches of open intake area.

    N. Large custom intake screen (optional for 1-5HP) shall be made of

    18 Gauge Series 300 Stainless Steel and completely enclose the motor power

    unit assembly. It shall have a minimum of 58% open area, representing 765square inches of open intake area. The screen hole size shall vary according

    to the horsepower for which it is to be used on.

    O. Nozzles (first one is included, must be specified, additional are

    optional) shall be interchangeable without the use of tools. Nozzles will be

    sealed to the float tube utilizing an o-ring and stainless steel thumb screws to

    prevent leakage.

    01/07Page 5

  • 8/3/2019 011-011

    6/33

    FIXED FOUNTAIN DETAIL SPECIFICATIONS

    2.0 DETAILED INFORMATION

    2.1 This specification is intended to provide prospective bidders the necessary

    information pertaining to the fixed fountain(s) specified for the_______________________ Project.

    2.2 The MOTOR(S) shall be _____ HP, operating at _____ Volts, 60 Hertz, _____ Phase at

    3450 RPM.

    2.3 The pattern specified shall be capable of creating a ________________________ pattern.

    It shall come complete with an electrical control panel, protective intake screen to

    be attached to a float assembly and ________ feet of _______ gauge, 3 (1/2 HP

    models only) or 4 conductor underwater power cable.

    2.4 The fountain shall produce a SPRAY PATTERN _____feet in diameter and _____feet in

    height.

    Please refer to TABLES 1, 2 and 3 to assist in the completion of SECTION 2.0

    01/07Page 6

  • 8/3/2019 011-011

    7/33

    FIXED FOUNTAIN DETAIL SPECIFICATIONS (cont.)

    3.0 ELECTRICAL CONTROL PANEL COMPONENTS DESCRIPTION

    A. Electrical enclosure shall be NEMA 3R type, galvanized and powder-

    coat painted gray in color. Panel shall be both lock and mount capable.

    B. GFCI breaker shall provide overload and short circuit protection,

    combined with Class A ground fault protection.

    C. Control breaker shall provide overload protection and be capable of

    disconnecting all incoming electricity from the control panel.

    D. Motor contactor shall provide a means for disconnection of all motor

    leads. It shall be a magnetic, across the line starter type.

    E. Overload assembly shall provide overload protection by means of a

    bi-metallic overload relay. It is adjustable over the full load amperage draw

    of the motor. It shall have a visual trip indicator, test button and

    manual/automatic reset modes.

    F. Timer shall be a single pole type, rated at 120 Volts, 20 Amps,

    capable of a timing cycle, in 30 minute increments up to 24 hours.

    3.1 SAFETY TESTING CONTROL PANEL

    The electrical control panel shall be tested and approved as a complete unit. It is

    inspected and listed by Underwriters Laboratories, Inc. under Category 508:

    Industrial Control Panels and Category 778: Submersible Aerators and Aerating

    Fountain Pump Systems.

    3.2 ACCEPTABLE MANUFACTURER

    This fixed fountains electrical control panel, as specified in Section 3.0, shall be

    manufactured by AQUAMASTER

    FOUNTAINS AND AERATORS, 16024 CTH X, Kiel, WI

    53042, (800) 693-3144 or approved equal.

    3.3 INSTALLATION

    The electrical control panel must be installed in accordance with the installation

    instructions, in compliance with all local and National Electrical Code requirements.

    This should be done by a licensed electrical contractor. Any alterations to or

    substitution for items in this system, unless allowed by the installation instructions,

    will void the Underwriters Laboratories Listing and will void the product warranty. It

    may also create a hazardous installation. Read the instructions thoroughly before

    starting the installation and follow them carefully throughout.

    01/07Page 7

  • 8/3/2019 011-011

    8/33

    3.4 ELECTRICAL CONTROL PANEL WARRANTY

    All electrical panel and on-shore components shall have a 1 year warranty.

    01/07Page 8

  • 8/3/2019 011-011

    9/33

    FIXED FOUNTAIN DETAIL SPECIFICATIONS (cont.)

    4.0 SAFETY TESTING

    The fixed fountain system shall be tested and approved as a complete unit. This

    approval must meet Underwriters Laboratories Inc. requirements in compliance with

    Category 508: Industrial Control Panels and Category 778: Submersible Aerators

    and Aerating Fountain Pump Systems. Individual component testing and wet niche

    environment equipment approval are not acceptable.

    4.1 ACCEPTABLE MANUFACTURER

    This fixed fountain, as specified in Sections 2.2, 2.3 and 2.4, shall be manufactured

    by AQUAMASTER

    FOUNTAINS AND AERATORS, 16024 CTH X, Kiel, WI 53042, (800)

    693-3144, or approved equal.

    4.2 INSTALLATION

    All AQUAMASTER

    FOUNTAINS are designed and built to be installed with an

    AQUAMASTER

    UL Listed control panel and to be operated as a complete system.

    Any alterations to or substitution for items in this system, unless allowed by the

    installation instructions, will void the UL Listing and will void the product warranty.

    It may also create a hazardous installation. Read the instructions thoroughly before

    starting the installation and follow them carefully throughout.

    4.3 WARRANTY

    All 1 5HP AQUAMASTER

    FOUNTAIN AERATORS motor, seal assembly, float and

    underwater power cable (referred to as in-water components) are covered under

    warranty at 100% replacement cost should it fail due to defects in materials or

    workmanship for a period of 3 years. This is in effect from the date of shipment,

    when given normal and proper usage as determined by The Seller upon

    examination, and when owned by the original user. All 1/2HP units have a similar 2

    year warranty.

    01/07Page 9

  • 8/3/2019 011-011

    10/3301/07

    Page 10

  • 8/3/2019 011-011

    11/33

    FIXED FOUNTAIN LIGHTING SYSTEMS AND OPTIONS SPECIFICATIONS

    5.0 LIGHTING SYSTEM shall be _______ Volt, Model #(s)______________.

    There are ______ total fixtures, containing ________________________

    (clear or choose color(s): amber, blue, red, green or turquoise) lenses.

    5.1 A total length of __________ feet of _______ gauge 3 conductor underwater power

    cable is required. Two runs of cable may be required; reference cable sizing chart.

    5.2 MULTI-PURPOSE ELECTRONIC LIGHT SYSTEM SEQUENCER shall be capable of

    cycling light fixtures off and on, up to 6 programs. Yes____No____

    5.3 A total length of __________ feet of _______ gauge, 4 conductor underwater power

    cable is required for sequencer. Two runs of cable may be required.

    5.4 LARGE CUSTOM INTAKE SCREEN (1-5HP) shall provide additional protected intake

    area if Fixed Fountain will operate in a potentially high debris filled aquatic

    environment. Yes ____ No _____

    Please refer to TABLES 2 and 3 to assist in the completion of SECTION 5.

    6.0 DESCRIPTION

    A. Lamp housings shall be of Series 300 Stainless Steel construction. They

    shall have a permanent Series 300 Stainless Steel electrical hub welded on the

    bottom of the housing to allow electrical cable entry and be trunnion mounted to

    cart framework for ease of light fixture adjustment.

    B. Construction shall consist of nonmetallic Cord Connectors to prevent water

    from entering the lamp housing. Lamp holders shall be double contact base

    constructed of stainless steel with wires rated for a minimum of 105 degrees

    Celsius. Reflectors shall be metal spun with Alzak finish for high reflectivity.

    Lamps shall be high intensity, quartz halogen flood, double contact bayonet

    base rated at 130VAC, mounted vertically.

    C. Light fixture assembly shall consist of V shaped Lamp gaskets made of

    silicon construction. Lens shall be of tempered glass with a clear non-diffusing

    surface with a minimum of 5/32nd

    thickness. Clamp ring shall be of Series 300

    Stainless Steel. Fasteners and mounting hardware shall be of Series 300

    stainless steel.

    01/07Page 11

  • 8/3/2019 011-011

    12/33

    D. Underwater Pin and Socket Connector shall consist of a Series 900, IP68

    pin and socket connector. It shall be of a 3 pin (4 pin when a sequencer is used)

    configuration rated 32 Amps at 600 VAC. The pin and socket ends shall each be

    attached to a 30 piece of UL Listed underwater power cable rated at 600 Volts.

    They both shall be permanently secured to their UL Listed power cables by a

    integrated neoprene grommet and compression nut assembly. These assemblies

    shall be epoxy filled to prevent entry of water or any other foreign matter. The

    pin end assembly shall be permanently attached to the light housing with a

    nonmetallic connector. This shall be potted using a flexible approved potting

    compound. The underwater disconnect is a two piece molded assembly made of

    glass reinforced nylon meeting UL 676 requirements. The socket end assembly

    shall be permanently attached to the underwater disconnect cap end with a

    nonmetallic connector. The body end of the underwater disconnect shall be

    permanently attached to the power cable assembly with a nonmetallic

    connector. Both cap and body ends shall be potted with an approved sealing

    compound. The disconnect shall be sealed with an o-ring and by and external

    Series 300 Stainless Steel clamp ring, which can be easily opened.

    E. Safety Testing Lighting shall be tested and approved as a complete

    assembly. This approval must meet Underwriters Laboratories Inc. requirements

    in compliance with UL Category 676: Underwater Lighting Fixtures.

    01/07Page 12

  • 8/3/2019 011-011

    13/3301/07

    Page 13

  • 8/3/2019 011-011

    14/33

    TABLE 1:CABLE SIZING CHARTS

    MAXIMUM RECOMMENDED LENGTH FOR FOUNTAIN TO CONTROL PANEL

    Single Phase 3 conductor 3 conductor Copper Wire Gauge Size

    Unit Volts

    Approx

    Amps

    #

    14

    #1

    2

    #1

    0 #8 #6 #4 #2

    1/2 HP 120 5.0

    17

    5 275 450 675

    100

    0 1700 2700

    1/2 HP 208-240 2.5

    55

    0 875

    140

    0

    220

    0

    350

    0 5500 8000

    4 conductor: Required on all 1 - 5HP Single Phase & ThreePhase Fountains

    Single Phase 4 conductor 4 conductor Copper Wire Gauge Size

    Unit Volts ApproxAmps #14 #12 #10 #8 #6 #4 #2

    1 HP 120 18.0 -- -- 130 200 325 500 800

    1 HP 208-240 9.0 -- 250 375 600

    100

    0 1500 2400

    2 HP 208-240 12.0 -- 200 300 475 775 1200 1900

    3.5 HP 208-240 15.0 -- -- 200 350 550 850 1350

    5 HP 208-240 26.0 -- -- 150 250 400 650 1000

    Three Phase 4 conductor 4 conductor Copper Wire Gauge Size

    Unit VoltsApproxAmps

    #14

    #12

    #10 #8 #6 #4 #2

    1 HP 208-240 5.0 -- 450 700

    120

    0

    180

    0 3000 4800

    1 HP 440-480 2.5 --

    170

    0

    270

    0

    430

    0

    690

    0

    1100

    0

    1750

    0

    2 HP 208-240 6.0 -- 300 500 800

    120

    0 1900 3100

    2 HP 440-480 3.0 --

    110

    0

    175

    0

    280

    0

    445

    0 7000

    1120

    0

    3 HP 208-240 10.0 -- 250 400 650

    100

    0 1650 2600

    3 HP 440-480 5.0 --

    100

    0

    160

    0

    255

    0

    400

    0 6400

    1000

    0

    01/07Page 14

  • 8/3/2019 011-011

    15/33

    5 HP 208-240 12.0 -- 150 250 400 600 950 1500

    5 HP 440-480 6.0 -- 600 950

    155

    0

    247

    5 3900 6250

    01/07Page 15

  • 8/3/2019 011-011

    16/33

    TABLE 2: FIXED FOUNTAIN LIGHTING SYSTEMS

    AQUAMASTER

    FIXED FOUNTAINS are even more dramatic at night, with the addition of a

    UL and cUL Listed NIGHT GLOW LIGHTING SYSTEM.

    Any lighting system choice includes stainless steel lamp housings, ready to be installed,sealed with clear tempered glass lenses in a stainless steel clamp ring. Minimal

    installation is required. All lights remain water-cooled and out of sight below the surface.

    All necessary electrical controls, including timer, are pre-wired into the fountains existing

    UL Listed control panel. Optional glass colored lenses (amber, blue, red, green or

    turquoise), with or without an optional sequencer complete your dramatic aquatic display.

    For uniformity of spray pattern coverage, 3 lights minimum is recommended.

    1. LINE VOLTAGE: 120 Volt Lighting Systems

    1/2 5 HP Fountain Lighting Systems available in 75, 150, or 250 watt fixtures

    75 Watt Fixtures 1/2 HP

    Units

    Each system includes:

    75 Watt Par 30 halogen flood lamps

    50 of underwater cable

    GFCI Protection

    Timer

    Clear lenses

    UL andcUL Listing

    2 light system: Model # 870352

    3 light system: Model # 870353

    4 light system: Model # 870354

    75 Watt Fixtures 1- 5 HP

    Units

    2 light system: Model # 870322

    3 light system: Model # 870323

    4 light system: Model # 870324

    150 Watt Fixtures 1/2 HP

    Units

    Each system includes:

    150 or 250 Watt quartz halogenflood lamps

    50 of underwater cable

    GFCI Protection

    Timer

    Clear lenses

    UL and cUL Listing

    2 light system: Model # 870362

    3 light system: Model # 870363

    4 light system: Model # 870364

    150 Watt Fixtures 1- 5 HP

    Units

    2 light system: Model # 870332

    01/07Page 16

  • 8/3/2019 011-011

    17/33

    3 light system: Model # 870333

    4 light system: Model # 870334

    250 Watt Fixtures 1/2 HP

    Units

    2 light system: Model # 870372

    3 light system: Model # 870373

    4 light system: Model # 870374

    250 Watt Fixtures 1- 5 HP

    Units

    2 light system: Model # 870342

    3 light system: Model # 870343

    4 light system: Model # 870344

    01/07Page 17

  • 8/3/2019 011-011

    18/33

    TABLE 3: FIXED FOUNTAIN LIGHTING SYSTEMS (cont.)

    CABLE SIZING CHART FOR LIGHTSMAXIMUM RECOMMENDED LENGTH FROM FOUNTAIN LIGHTS TO CONTROL

    PANEL

    3 Conductor Copper Wire Gauge Size

    WattsPer

    Fixture

    # ofFixtures

    Volts

    Approx

    Amps

    #14

    #12

    #10

    #8 #6 #4 #2

    75 2 120 1.3750

    1200

    2000

    3000

    5000

    8000

    13000

    75 3 120 1.9500 800

    1300

    2000

    3300

    5700 9000

    75 4 120 2.5400 600

    1000

    1600

    2500

    4300 6900

    150 2 120 2.5400 600

    1000

    1600

    2500

    4300 6900

    150 3 120 3.8 250 400 650 1000 1650 2800 4500

    150 4 120 5200 300 500 800

    1200

    2100 3400

    250 2 120 4.2250 400 640

    1000

    1600

    2500 4100

    250 3 120 6.3160 260 420 675

    1050

    1700 2700

    250 4 120 8.5100 200 300 500 750

    1250 2000

    CABLE SIZING CHART FOR LIGHTS WHEN ORDERED WITH A SEQUENCERMAXIMUM RECOMMENDED LENGTH FROM FOUNTAIN LIGHTS TO

    CONTROL PANEL

    3 & 4 Conductor see notes below Copper Wire Gauge SizeWatts Per

    Fixture# of Fixtures

    Volts

    #14

    #12

    #10

    #8 #6 #4 #2

    75 3 or 4 120800

    1200

    2000

    3200

    5000 - -

    75 6 (3 colors) 120400 600

    1000

    1600

    2500 - -

    75 8 (4 colors) 120400 600

    1000

    1600

    2500 -

    150 3 or 4 120400 600

    1000

    1600

    2500

    4300 -

    150 6 (3 colors) 120200 300 500 800

    1250

    2150 -

    150 8 (4 colors) 120200 300 500 800

    1250

    2150 -

    250 3 or 4 120 25 400 650 100 160 26 -

    01/07Page 18

  • 8/3/2019 011-011

    19/33

    0 0 0 00

    250 6 (3 colors) 120125 200 325 500 800

    1300 -

    250 8 (4 colors) 120125 200 325 500 800

    1300

    Lighting sequencer requires 2 runsof cable:

    1) Sequencer with 3 colors require (1) run of 3 conductor cableand (1) run of 4 conductor cable2) Sequencer with 4 colors require (2) runs of4 conductor cable

    P/Fixing of Glass Mosaic of approved shades of Zestha,Palladio, Bisazza make onlyincluding Chemical Adhesive(Bal Endura-Diamondstar), Grout Powder( Bal Endura-Diamondstar) complete in all respects including cleaning of the same as per Drawing

    attached herewith showing the dimensions of each point.

    Ripples Engineering Pvt. Ltd

    C-119, Phase - II Extension, Noida (U.P)

    Tel: 0120-2461911-15, Fax: 0120-2461910

    Email: [email protected]

    3153/R/PS/ 218

    Dated 16/11/11

    Gautam Banerjee

    Bhopal IN

    Kind Attn. : Mr. Gautam Banerjee

    Subject :- Quote for the providing, fixing, testing & commissioning of water fetures

    01/07Page 19

  • 8/3/2019 011-011

    20/33

    Dear Sir,

    Please find below our quote for the providing, fixing, testing & commissioning of water

    features, based on the

    drawings we received from you.

    Remarks. : Wiring distance from water body sump to plant room/panel taken as 15m. as

    per information available,

    incase of change beyond 10% cost of wiring would change on pro-rata basis

    Item Code Description Make/Brand Qty UoM Rate Amount

    Water Body 1 : Providing, fixing, testing & commissioning of Geyser Jet Fountain (for 1.8

    mtr. dia pool)

    Providing, fixing, testing & commissioning of Nozzles

    NOZ16.11 Geyser 25N (M.O.C Gunmetal - Noryl) Ripples 4 No 1,553.00 6,212.00 INR

    NOZ16.12 Geyser 40N (M.O.C Gunmetal - Noryl) Ripples 1 No 2,329.00 2,329.00 INR

    NOZ13.08 Floor Inlet Nozzle (ABS)(3 PCs./Set)

    Adjustable Ripples Make

    Ripples 3 No 225.00 675.00 INR

    Providing, fixing, testing & commissioning of Lights

    LED1.03 NL418LN/W Submersible LED Light - Warm

    White 18W (6x3W LED's)

    Ripples 11 No 4,169.00 45,859.00 INR

    MOL1.42 Niche for NL 418LN - Nylon Ripples 11 No 230.00 2,530.00 INR

    ELX2.20 Power Supply - 18V DC/15 Amp. (Make-

    PE)

    PE 1 No 10,120.00 10,120.00 INR

    EL6.02 Junction Box 180/8 MOC Nylon MakeRipples

    Ripples 2 No 978.00 1,956.00 INR

    Providing, fixing, testing & commissioning of Suction inlet fittings

    SWA2.240 Suction Point (2 Pcs./Set)ABS(Ripples) Ripples 1 No 184.00 184.00 INR

    Providing, fixing, testing & commissioning of Dosing Unit

    SWA4.09 Chlorine/ Bromine Dosing Unit (IN-LINE

    01/07Page 20

  • 8/3/2019 011-011

    21/33

    Feeder)- Ripples

    Ripples (Brand) 1 No 4,526.00 4,526.00 INR

    Providing, fixing, testing & commissioning of Filter

    SWA4.01 Sand/Bio Filter Top-mounted with 40mm

    MPV (T 450-18") flow 8 m3/hr. - Ripples

    Ripples (Brand) 1 No 19,323.00 19,323.00 INR

    SWA2.18 Sand for Sand Filter (SIZE 16/32 Mesh) 50 Kg 14.00 700.00 INR

    Providing, fixing, testing & commissioning of Pumps

    OP8.07 Pump 3Hp Submersible 3 Phase

    (SHOOL32TAE/65x65) C.G.

    Crompton 1 No 21,758.00 21,758.00 INR

    OP7.13 Pump 1Hp Submersible 1 Phase

    (SHOEM12SAM30/32X25) C.G.

    Crompton 1 No 13,854.00 13,854.00 INR

    REGD. OFFICE:G-36, Green Park Main Mkt., New Delhi-110016, Ph. : +91-11-26524682,

    26856164, Fax: 26855645

    E-mail: [email protected]

    01/07Page 21

  • 8/3/2019 011-011

    22/33

    Item Code Description Make/Brand Qty UoM Rate Amount

    Providing, fixing, testing & commissioning of Control Panel

    PNL2.05 Panel Body for Two Pump with

    Transformer

    Ripples 1 No 7,105.00 7,105.00 INR

    PNL3.14 Three Phase Panel Incomer 1 No 6,506.00 6,506.00 INR

    PNL3.01 Starter for 3HP Submersible Pump Three

    Phase

    1 No 8,165.00 8,165.00 INR

    PNL3.07 Starter for 1HP Submersible Pump Single

    Phase

    1 No 7,310.00 7,310.00 INR

    Providing and fixing of pipes (uPVC pipe- 10kg. Pressure) & fittings (Heavy) including

    Elbow, Tee, Socket

    etc.

    PL53.03 uPVC Pipe OD 32 (10 Kg.) Finolex/Prince/S

    upreme

    6 Mtr 58.00 348.00 INR

    PL53.05 uPVC Pipe OD 50 (10 Kg.) Finolex/Prince/S

    upreme

    30 Mtr 135.00 4,050.00 INR

    PL53.08 uPVC Pipe OD 90 (10 Kg.) Finolex/Prince/S

    upreme

    3 Mtr 428.00 1,284.00 INR

    Providing & fixing of Valves, fittings etc of required size

    PL5.06 Brass Ball Valve 40mm Imported 6 No 1,109.00 6,654.00 INR

    PL5.04 Brass Ball Valve 25mm Imported 4 No 496.00 1,984.00 INR

    PL10.12 NRV - 40mm (Flap/Wafer Type - C.I.) Quin/Krishna 1 No 704.00 704.00 INRPL47.03 MS Flange 40 NB - Threaded (for NRV

    40mm )

    2 No 235.00 470.00 INR

    PL28.05 GI Nipple 40 NB 3 No 99.00 297.00 INR

    PL86.03 SS Nipple 25mm 4 No 275.00 1,100.00 INR

    PL86.05 SS Nipple 40mm 1 No 365.00 365.00 INR

    01/07Page 22

  • 8/3/2019 011-011

    23/33

    Providing & fixing of Wires/cables including necessary accessories

    EL29.80 Wire 2.5mm Three Core (Flat) Power

    Lite/Everest

    20 Mtr 154.00 3,080.00 INR

    EL29.75 Wire 1.5mm Three Core (Flat) Power

    Lite/Everest

    20 Mtr 104.00 2,080.00 INR

    EL29.116 Wire 1.5mm Two Core (Round) Power

    Lite/Everest

    50 mtr 71.00 3,550.00 INR

    Providing and fixing of conduits, bends, fittings etc. of required size

    PL60.02 PVC Conduit 20mm AKG/Sethia 20 Mtr 22.00 440.00 INR

    PL60.03 PVC Conduit 25mm AKG/Sethia 70 Mtr 30.00 2,100.00 INR

    PL60.04 PVC Conduit 32mm AKG/Sethia 20 Mtr 46.00 920.00 INR

    Subtotal 188,538.00 INR

    Water Body 2 : Providing, fixing, testing & commissioning of Dome Fountain (for 3.6 mtr.

    dia pool)

    Providing, fixing, testing & commissioning of Nozzles

    NOZ26.13 Vertical Jet AF-20 -10mm bore Ripples 56 No 520.00 29,120.00 INR

    NOZ26.10 Vertical Jet AF-40 -19mm bore Ripples 1 No 4,016.00 4,016.00 INR

    NOZ13.08 Floor Inlet Nozzle (ABS)(3 PCs./Set)

    Adjustable Ripples Make

    Ripples 3 No 225.00 675.00 INR

    Providing, fixing, testing & commissioning of Ring 3.6 mtr. dia

    NOZ33.05 GI Ring 65NB (Per Linear Meter) Ripples 11.31 Mtr 1,086.00 12,282.66 INR

    REGD. OFFICE:G-36, Green Park Main Mkt., New Delhi-110016, Ph. : +91-11-26524682,

    26856164, Fax: 26855645

    E-mail: [email protected]

    01/07Page 23

  • 8/3/2019 011-011

    24/33

    Item Code Description Make/Brand Qty UoM Rate Amount

    Providing, fixing, testing & commissioning of Lights

    LED1.02 SL418LN/W Submersible LED Light - Warm

    White 18W (6x3W LED's)

    Ripples 17 No 4,169.00 70,873.00 INR

    ELX2.20 Power Supply - 18V DC/15 Amp. (Make-

    PE)

    PE 1 No 10,120.00 10,120.00 INR

    EL6.02 Junction Box 180/8 MOC Nylon Make

    Ripples

    Ripples 3 No 978.00 2,934.00 INR

    EL13.12 SS Light Stand 3 Way 40 NB Ripples 1 No 500.00 500.00 INR

    Providing, fixing, testing & commissioning of Pumps

    OP7.13 Pump 1Hp Submersible 1 Phase

    (SHOEM12SAM30/32X25) C.G.

    Crompton 1 No 13,854.00 13,854.00 INR

    OP7.05 Pump 2HP Submersible 1 Phase

    (OSK22/50x40) C.G. Discharge -305 LPM

    @ 10.5mtr. Head, Starting-DOL

    Crompton 1 No 18,400.00 18,400.00 INR

    OP8.44 Pump 5HP Submersible 3 Phase

    (OSQ52/80X80) C.G.

    Crompton 2 No 23,895.00 47,790.00 INR

    Providing, fixing, testing & commissioning of Suction inlet fittings

    SWA2.240 Suction Point (2 Pcs./Set)ABS(Ripples) Ripples 1 No 184.00 184.00 INR

    Providing, fixing, testing & commissioning of Dosing Unit

    SWA4.09 Chlorine/ Bromine Dosing Unit (IN-LINE

    Feeder)- RipplesRipples (Brand) 1 No 4,526.00 4,526.00 INR

    Providing, fixing, testing & commissioning of Filter

    SWA4.01 Sand/Bio Filter Top-mounted with 40mm

    MPV (T 450-18") flow 8 m3/hr. - Ripples

    Ripples (Brand) 1 No 19,323.00 19,323.00 INR

    SWA2.18 Sand for Sand Filter (SIZE 16/32 Mesh) 50 Kg 14.00 700.00 INR

    01/07Page 24

  • 8/3/2019 011-011

    25/33

    Providing, fixing, testing & commissioning of Control Panel

    PNL2.09 Panel Body for Four Pump with

    Transformer

    Ripples 1 No 15,496.00 15,496.00 INR

    PNL3.14 Three Phase Panel Incomer 1 No 6,506.00 6,506.00 INR

    PNL3.09 Starter for 2HP Submersible Pump Single

    Phase

    1 No 8,120.00 8,120.00 INR

    PNL3.07 Starter for 1HP Submersible Pump Single

    Phase

    1 No 7,310.00 7,310.00 INR

    PNL3.02 Starter for 5HP Submersible Pump Three

    Phase

    2 No 10,284.00 20,568.00 INR

    Providing and fixing of pipes (uPVC pipe- 10kg. Pressure) & fittings (Heavy) including

    Elbow, Tee, Socket

    etc.

    PL53.06 uPVC Pipe OD 63 (10 Kg.) Finolex/Prince/S

    upreme

    15 Mtr 212.00 3,180.00 INR

    PL53.05 uPVC Pipe OD 50 (10 Kg.) Finolex/Prince/S

    upreme

    40 Mtr 135.00 5,400.00 INR

    PL53.13 uPVC Pipe OD 140 (10 Kg.) Finolex/Prince/S

    upreme

    3 Mtr 1,070.00 3,210.00 INR

    Providing & fixing of Valves, fittings etc of required size

    PL5.06 Brass Ball Valve 40mm Imported 9 No 1,109.00 9,981.00 INR

    PL10.12 NRV - 40mm (Flap/Wafer Type - C.I.) Quin/Krishna 1 No 704.00 704.00 INRPL47.03 MS Flange 40 NB - Threaded (for NRV

    40mm )

    2 No 235.00 470.00 INR

    PL28.05 GI Nipple 40 NB 3 No 99.00 297.00 INR

    PL86.05 SS Nipple 40mm 1 No 365.00 365.00 INR

    01/07Page 25

  • 8/3/2019 011-011

    26/33

    REGD. OFFICE:G-36, Green Park Main Mkt., New Delhi-110016, Ph. : +91-11-26524682,

    26856164, Fax: 26855645

    E-mail: [email protected]

    01/07Page 26

  • 8/3/2019 011-011

    27/33

    Item Code Description Make/Brand Qty UoM Rate Amount

    Providing & fixing of Wires/cables of various sizes including necessary accessories

    EL29.75 Wire 1.5mm Three Core (Flat) Power

    Lite/Everest

    45 Mtr 104.00 4,680.00 INR

    EL29.116 Wire 1.5mm Two Core (Round) Power

    Lite/Everest

    90 mtr 71.00 6,390.00 INR

    EL29.80 Wire 2.5mm Three Core (Flat) Power

    Lite/Everest

    45 Mtr 154.00 6,930.00 INR

    Providing and fixing of conduits, bends, fittings etc. of required size

    PL60.02 PVC Conduit 20mm AKG/Sethia 50 Mtr 22.00 1,100.00 INR

    PL60.03 PVC Conduit 25mm AKG/Sethia 135 Mtr 30.00 4,050.00 INR

    Subtotal 340,054.66 INR

    Water Body 3 (Arc Shape Water Body) : Providing, fixing, testing & commissioning of

    Geyser Jet Fountain

    Providing, fixing, testing & commissioning of Nozzles

    NOZ16.11 Geyser 25N (M.O.C Gunmetal - Noryl) Ripples 20 No 1,553.00 31,060.00 INR

    NOZ13.08 Floor Inlet Nozzle (ABS)(3 PCs./Set)

    Adjustable Ripples Make

    Ripples 4 No 225.00 900.00 INR

    Providing, fixing, testing & commissioning of Lights

    LED1.18 NL409LN/W Submersible LED Light Warm

    White 9W (3X3W LEDs)

    Ripples 40 No 1,898.00 75,920.00 INR

    MOL1.52 Niche for NL409LN Nylon Ripples 40 No 173.00 6,920.00 INR

    ELX2.19 Power Supply - 9V DC/15 Amp. (Make PE)PE 2 No 5,951.00 11,902.00 INR

    EL6.02 Junction Box 180/8 MOC Nylon Make

    Ripples

    Ripples 8 No 978.00 7,824.00 INR

    Providing, fixing, testing & commissioning of Suction inlet fittings

    SWA2.240 Suction Point (2 Pcs./Set)ABS(Ripples) Ripples 1 No 184.00 184.00 INR

    01/07Page 27

  • 8/3/2019 011-011

    28/33

    SWA2.40 Vacuum Point (2 Pcs./Set)ABS(Ripples) Ripples 1 No 184.00 184.00 INR

    Providing, fixing, testing & commissioning of Dosing Unit

    SWA4.09 Chlorine/ Bromine Dosing Unit (IN-LINE

    Feeder)- Ripples

    Ripples (Brand) 1 No 4,526.00 4,526.00 INR

    Providing, fixing, testing & commissioning of Filter

    SWA4.01 Sand/Bio Filter Top-mounted with 40mm

    MPV (T 450-18") flow 8 m3/hr. - Ripples

    Ripples (Brand) 1 No 19,323.00 19,323.00 INR

    SWA2.18 Sand for Sand Filter (SIZE 16/32 Mesh) 50 Kg 14.00 700.00 INR

    Providing, fixing, testing & commissioning of Pumps

    OP8.44 Pump 5HP Submersible 3 Phase

    (OSQ52/80X80) C.G.

    Crompton 2 No 23,895.00 47,790.00 INR

    OP7.13 Pump 1Hp Submersible 1 Phase

    (SHOEM12SAM30/32X25) C.G.

    Crompton 1 No 13,854.00 13,854.00 INR

    Providing, fixing, testing & commissioning of Control Panel

    PNL2.07 Panel Body for Three Pump with

    Transformer

    Ripples 1 No 11,742.00 11,742.00 INR

    PNL3.14 Three Phase Panel Incomer 1 No 6,506.00 6,506.00 INR

    PNL3.07 Starter for 1HP Submersible Pump Single

    Phase

    1 No 7,310.00 7,310.00 INR

    PNL3.02 Starter for 5HP Submersible Pump Three

    Phase

    2 No 10,284.00 20,568.00 INR

    REGD. OFFICE:G-36, Green Park Main Mkt., New Delhi-110016, Ph. : +91-11-26524682,

    26856164, Fax: 26855645

    E-mail: [email protected]

    01/07Page 28

  • 8/3/2019 011-011

    29/33

    Item Code Description Make/Brand Qty UoM Rate Amount

    Providing and fixing of pipes (uPVC pipe- 10kg. Pressure) & fittings (Heavy) including

    Elbow, Tee, Socket

    etc.

    PL53.13 uPVC Pipe OD 140 (10 Kg.) Finolex/Prince/S

    upreme

    12 Mtr 1,070.00 12,840.00 INR

    PL53.08 uPVC Pipe OD 90 (10 Kg.) Finolex/Prince/S

    upreme

    12 Mtr 428.00 5,136.00 INR

    PL53.03 uPVC Pipe OD 32 (10 Kg.) Finolex/Prince/S

    upreme

    12 Mtr 57.00 684.00 INR

    PL53.05 uPVC Pipe OD 50 (10 Kg.) Finolex/Prince/S

    upreme

    60 Mtr 135.00 8,100.00 INR

    Providing & fixing of Valves, fittings etc of required size

    PL5.06 Brass Ball Valve 40mm Imported 6 No 1,109.00 6,654.00 INR

    PL5.04 Brass Ball Valve 25mm Imported 20 No 496.00 9,920.00 INR

    PL10.12 NRV - 40mm (Flap/Wafer Type - C.I.) Quin/Krishna 1 No 704.00 704.00 INR

    PL47.03 MS Flange 40 NB - Threaded (for NRV

    40mm )

    2 No 235.00 470.00 INR

    PL86.03 SS Nipple 25mm 20 No 275.00 5,500.00 INR

    PL28.05 GI Nipple 40 NB 3 No 99.00 297.00 INR

    Providing & fixing of Wires/cables of various sizes including necessary accessories

    EL29.75 Wire 1.5mm Three Core (Flat) Power

    Lite/Everest25 Mtr 104.00 2,600.00 INR

    EL29.116 Wire 1.5mm Two Core (Round) Power

    Lite/Everest

    300 mtr 71.00 21,300.00 INR

    EL29.80 Wire 2.5mm Three Core (Flat) Power

    Lite/Everest

    01/07Page 29

  • 8/3/2019 011-011

    30/33

    60 Mtr 154.00 9,240.00 INR

    Providing and fixing of conduits, bends, fittings etc. of required size

    PL60.02 PVC Conduit 20mm AKG/Sethia 100 Mtr 22.00 2,200.00 INR

    PL60.03 PVC Conduit 25mm AKG/Sethia 325 Mtr 30.00 9,750.00 INR

    PL60.04 PVC Conduit 32mm AKG/Sethia 60 Mtr 46.00 2,760.00 INR

    Subtotal 365,368.00 INR

    Pool Cleaning Kit

    SWA4.30 Vaccum Hose 50 Ft. Spiral Wound EVA Dia.

    40mm - Ripples

    Ripples (Brand) 1 No 8,965.00 8,965.00 INR

    SWA4.08 Leaf Skimmer - Standard Ripples Ripples (Brand) 1 No 391.00 391.00 INR

    SWA4.07 Brush Curved 18"/45cm. (Standard

    Polybristle Wall Brush) - Ripples

    Ripples (Brand) 1 No 695.00 695.00 INR

    SWA4.06 Vacuum Head Deluxe Triangular

    Transparent Cast Iron Weighted - Ripples

    Ripples (Brand) 1 No 2,958.00 2,958.00 INR

    SWA4.05 Telescopic pole 2x120cm. - 0.8mm Thick Al.

    Tubbing white -2.5mtr Long - Ripples

    Ripples (Brand) 1 No 1,628.00 1,628.00 INR

    Subtotal 14,637.00 INR

    PAF1.05 Packing & Forwading Charges 1 No 16,000.00 16,000.00 INR

    REGD. OFFICE:G-36, Green Park Main Mkt., New Delhi-110016, Ph. : +91-11-26524682,

    26856164, Fax: 26855645

    E-mail: [email protected]

    01/07Page 30

  • 8/3/2019 011-011

    31/33

    Item Code Description Make/Brand Qty UoM Rate Amount

    OS1.02 Outstation charges- (Boarding, lodging &

    travel cost of our project teams).

    1 No 32,000.00 32,000.00 INR

    Summary of Cost

    Tax

    Grand Total

    129,011.79 INR

    1,085,609.45 INR

    EXCLUSIONS:

    Safe custody of material at site.

    Providing necessary power supply near the Control Panel

    Earthing work required for the fountain equipment.

    Civil work if any.

    Providing inlet and drain for the water body

    TERMS AND CONDITIONS OF CONTRACT:

    Price : FOR Site.

    Payment : 35% Advance along with order, 50% On completion of plumbing & conduiting

    work within the water

    body and Prior to dispatch of capital material & 15% on Completion

    Warranty : One Year from date of commisioning.Validity : One Month from date of Quote

    Delivery : 8-10 weeks from date of order and Advance.

    Taxes : Included (CST @ 13.5% on 80% of value & Service Tax @ 3.40% on 100% of value)

    Note : (i) Tax not applicable on packing forwarding & outstation charges

    01/07Page 31

  • 8/3/2019 011-011

    32/33

    We hope our quote is in line with your requirement. Should you need any further

    information / clarifications please

    feel free to contact us.

    We look forward to receiving your valued order.

    Yours truly,

    For Ripples Engineering Pvt Ltd

    Pankaj Sharma

    (Sr. Sales Officer)

    Mob : 9350001909

    Email : [email protected]

    REGD. OFFICE:G-36, Green Park Main Mkt., New Delhi-110016, Ph. : +91-11-26524682,

    26856164, Fax: 26855645

    E-mail: [email protected]

    01/07Page 32

  • 8/3/2019 011-011

    33/33