Upload
ciaran-mcauley
View
220
Download
2
Embed Size (px)
Citation preview
WCDMA BTS Rel1 HWconfigurations
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
1 (33)
469300A.4_0Nokia UltraSite WCDMA BTS Optima Compact,Rel2
The information in this document is subject to change without notice and describes only theproduct defined in the introduction of this documentation. This document is intended for the useof Nokia's customers only for the purposes of the agreement under which the document issubmitted, and no part of it may be reproduced or transmitted in any form or means without theprior written permission of Nokia. The document has been prepared to be used by professionaland properly trained personnel, and the customer assumes full responsibility when using it.Nokia welcomes customer comments as part of the process of continuous development andimprovement of the documentation.
The information or statements given in this document concerning the suitability, capacity, orperformance of the mentioned hardware or software products cannot be considered binding butshall be defined in the agreement made between Nokia and the customer. However, Nokia hasmade all reasonable efforts to ensure that the instructions contained in the document areadequate and free of material errors and omissions. Nokia will, if necessary, explain issueswhich may not be covered by the document.
Nokia's liability for any errors in the document is limited to the documentary correction of errors.NOKIA WILL NOT BE RESPONSIBLE IN ANY EVENT FOR ERRORS IN THIS DOCUMENTOR FOR ANY DAMAGES, INCIDENTAL OR CONSEQUENTIAL (INCLUDING MONETARYLOSSES), that might arise from the use of this document or the information in it.
This document and the product it describes are considered protected by copyright according tothe applicable laws.
NOKIA logo is a registered trademark of Nokia Corporation.
Other product names mentioned in this document may be trademarks of their respectivecompanies, and they are mentioned for identification purposes only.
Copyright © Nokia Corporation 2003. All rights reserved.
2 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
Contents
Contents 3
1 Installing WOC and WPD units 51.1 Installing the WOC unit 51.2 Installing a WPD unit 7
2 WSM cabling 92.1 Connecting WSM unit cables 9
3 Typical BTS configurations 133.1 RF extension cabinet configurations 133.1.1 1-carrier omni configuration (1+0+0) 133.1.2 1+1+0 configuration 163.1.3 1+1+1 configuration 183.1.4 6x1 configuration 203.1.5 2+2+2 configuration 223.1.6 3x (1+1) ROC configuration 243.1.7 1+1+1 ROC configuration 263.2 IBBU cabinet configurations 283.2.1 IBBU 1+0+0 configuration 283.2.2 IBBU 1+1+1 configuration 303.2.3 IBBU 1+1+1 ROC configuration 32
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
3 (33)
Contents
4 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
1 Installing WOC and WPD units
1.1 Installing the WOC unit
Steps
1. Attach the long output cable of the WOC to the appropriate WAF unitsocket
Tighten slightly so that the WOC cable connector cannot be jerked freefrom the socket. See the Installing the WOC unit diagram.
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
5 (33)
Installing WOC and WPD units
Figure 1. Installing the WOC unit
2. Attach the other two WOC cables to the WPA unit sockets
Tighten slightly so that the WOC cable connectors cannot be jerked freefrom the sockets.
3. Tighten each WOC cable connector in even intervals to a torque of 1Nm
DN02207043
WAF
Long output cable
WPA
6 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
Note
Use care when bending the WOC cables. If bending a WOC cable to the front orback (as opposed to bending it to the side), first ensure that the cable is straight.
Note
When tightening the WOC cable connectors with a torque wrench to a torque of 1Nm, hold the other cable connector steady with another torque wrench so that itdoes not bend.
Expected outcome
The WOC unit is successfully installed.
1.2 Installing a WPD unit
Purpose
The WPD unit is used in the ROC configurations.
It should be installed according to these instructions and the appropriateconfiguration diagram.
Steps
1. Remove any unnecessary blanco panels
Remove any blanco panels from the slot(s) in which the WPD unit(s) willbe installed.
2. Slide the WPD unit into place and tighten the screws
Slide the WPD unit carefully into place, then tighten the screws to therecommended torque as specified in the Torque Values section.
3. Attach the appropriate cables to the WPD unit
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
7 (33)
Installing WOC and WPD units
Attach the appropriate cables to the WPD unit, tightening the connectors tothe recommended torque as specified in the Torque Values section.
Expected outcome
The WPD unit is successfully installed.
8 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
2 WSM cabling
2.1 Connecting WSM unit cables
Before you start
There are 3 WSM units in the RF extension cabinet and 2 WSM units in theIBBU cabinet.
The cable is delivered with the WSM unit, code: 993929
Note
Refer to steps 1 and 2 if your cabinet is the RF extension cabinet. Refer only tostep 3 if your cabinet is the IBBU cabinet.
Steps
1. Fix the connectors from the bottom WSM (shelf 3, slot 1)
From the L-connector to the R-connector in the middle WSM (shelf 2, slot1) and from the R-connector to the L-connector in the top WSM (shelf 1,slot 8).
See the WSM cabling for RF extension cabinet diagram.
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
9 (33)
WSM cabling
Figure 2. WSM cabling for RF extension cabinet
DN02206944
Shelf 1Slot 8
Shelf 2Slot 1
Shelf 3Slot 1
10 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
2. Connect the cables from the middle WSM
From the L-connector to the R-connector in the top WSM and from the R-connector to the L-connector in the bottom WSM.
3. Fix the connectors from the bottom WSM (shelf 3, slot 1)
Do this only if the cabinet is the IBBU cabinet version. From the L-connector to the R-connector in the middle WSM (shelf 2, slot 1) and fromthe R-connector to the L- connector in the middle WSM. See the WSMcabling for IBBU cabinet diagram.
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
11 (33)
WSM cabling
Figure 3. WSM cabling for IBBU cabinet
DN02206956
Shelf 2Slot 1
Shelf 3Slot 1
12 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
3 Typical BTS configurations
3.1 RF extension cabinet configurations
3.1.1 1-carrier omni configuration (1+0+0)
Purpose
Diagram Unit connectors and cables in a typical 1-carrier omni configurationshows the connectors and cables in a typical 1-carrier omni configuration.
Diagram 1+0+0 omni configuration shows the unit positions and cables in RFextension cabinet 1-carrier omni configuration. The 1-carrier omni configurationis the smallest possible configuration.
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
13 (33)
Typical BTS configurations
Figure 4. Unit connectors and cables in a typical 1-carrier omni configuration
= terminator part
DN02206983
1
2
2 1
ANT DIV
ANT MAIN
RX1
RX2
RX3
RX4
TX
RXDIV1
RXDIV2
RXDIV4
RXDIV3
TX Out
TX In
TX
RX2
RX1
DIVOut1
DIVOut2
DIVIn
CombOut
CombIn1
CombIn2
14 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
Figure 5. 1+0+0 omni configuration
2 1
DN02206995= terminator part
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
15 (33)
Typical BTS configurations
Before you start
Note
Bend any excess cable from its top.
Note
For torque recommendations, see Torque values section.
Steps
1. Connect the front cables
For information on the front cables see the The cables in the front cable setsection.
2. Tighten the cables
3.1.2 1+1+0 configuration
Purpose
Diagram 1+1+0 configuration shows the unit positions and cables in RFextension cabinet 1+1+0 configuration.
Before you start
Note
For recommended torque vales for tightening each connector, see Torque valuessection.
Steps
1. Connect the front cables
16 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
Figure 6. 1+1+0 configuration
For information on the front cables see the The cables in the front cable setsection.
2. Tighten the cables
DN02207004= terminator part
2 1 6 5
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
17 (33)
Typical BTS configurations
3.1.3 1+1+1 configuration
Purpose
Diagram 1+1+1 configuration shows the unit positions and cables in RFextension cabinet 1+1+1 configuration.
Before you start
Note
For recommended torque vales for tightening each connector, see Torque valuessection.
Steps
1. Connect the front cables
18 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
Figure 7. 1+1+1 configuration
For information on the front cables see the The cables in the front cable setsection.
2. Tighten the cables
DN02207016= terminator part
2 1 6 5 10 9
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
19 (33)
Typical BTS configurations
3.1.4 6x1 configuration
Purpose
Diagram 6x1 configuration shows the unit positions and cables in RF extensioncabinet 6x1 configuration.
Before you start
Note
For recommended torque vales for tightening each connector, see Torque valuessection.
Steps
1. Connect the front cables
20 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
Figure 8. 6x1 configuration
For information on the front cables see the The cables in the front cable setsection.
2. Tighten the cables
DN02207028
= terminator part
12
12
12
12
12
12
4 3 6 5 8 7 10 9 12 112 1
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
21 (33)
Typical BTS configurations
Note
If you need 6x2 RF chaining, refer to RF chaining cabling list section.
3.1.5 2+2+2 configuration
Purpose
Diagram 2+2+2 configuration shows the unit positions and cables in RFextension cabinet 2+2+2 configuration.
Before you start
Note
For recommended torque vales for tightening each connector, see Torque valuessection.
Steps
1. Connect the front cables
22 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
Figure 9. 2+2+2 configuration
For information on the front cables see the The cables in the front cable setsection.
2. Tighten the cables
DN02207031
2 1
= terminator part
6 5 8 7 10 9
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
23 (33)
Typical BTS configurations
3.1.6 3x (1+1) ROC configuration
Purpose
Diagram 3x (1+1) ROC configuration for RF extension cabinet shows the unitpositions and cables in RF extension cabinet 3x (1+1) ROC configuration.
Before you start
Note
For recommended torque vales for tightening each connector, see Torque valuessection.
Steps
1. Attach the WPD unit to the cabinet
ROC configurations need 1-3 WPD units. WPDA/WPDB units aredelivered with the other units according to the configuration the customerordered. AWPD unit is attached to a blanco panel, and therefore it can beinstalled in the same manner; fixing it to the cabinet core with 4 screwsfrom its corners. To install a WPD unit, remove the blanco panel from thecabinet, and according to the desired configuration, replace it by a WPDunit attached to a blanco panel.
2. Connect the front cables
24 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
Figure 10. 3x (1+1) ROC configuration for RF extension cabinet
For information on the front cables see the The cables in the front cable setsection.
3. Tighten the cables
DN02207055
= terminator part
12
12
12
12
12
12
4 3 6 5 8 7 10 9 12 112 1
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
25 (33)
Typical BTS configurations
3.1.7 1+1+1 ROC configuration
Purpose
Diagram 1+1+1 ROC configuration for RF extension cabinet shows the unitpositions and cables in RF extension cabinet 1+1+1 ROC configuration.
Before you start
Note
For recommended torque vales for tightening each connector, see Torque valuessection.
Note
ROC configurations need 1-3 WPD units. WPDA/WPDB units are delivered withthe other units according to the configuration the customer ordered. AWPD unitis attached to a blanco panel, and therefore it can be installed in the same manner;fixing it to the cabinet core with 4 screws from its corners. To install a WPD unit,remove the blanco panel from the cabinet, and according to the desiredconfiguration, replace it by a WPD unit attached to a blanco panel.
Steps
1. Attach the WPD unit to the cabinet
AWPD unit is attached to a blanco panel, and therefore it can be installedin the same manner; fixing it to the cabinet core with 4 screws from itscorners.
2. Connect the front cables
26 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
Figure 11. 1+1+1 ROC configuration for RF extension cabinet
For information on the front cables see the The cables in the front cable setsection.
3. Tighten the cables
DN02207067= terminator part
2 1 6 5 10 9
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
27 (33)
Typical BTS configurations
3.2 IBBU cabinet configurations
3.2.1 IBBU 1+0+0 configuration
Purpose
Diagram IBBU 1+0+0 configuration shows the unit positions and cables inIBBU 1+0+0 configuration.
Before you start
Note
For recommended torque vales for tightening each connector, see Torque valuessection.
Steps
1. Connect the front cables
28 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
Figure 12. IBBU 1+0+0 configuration
For information on the front cables see the The cables in the front cable setsection.
2. Tighten the cables
2 1
DN02207079= terminator part
21
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
29 (33)
Typical BTS configurations
3.2.2 IBBU 1+1+1 configuration
Purpose
Diagram IBBU 1+1+1 configuration shows the unit positions and cables inIBBU 1+1+1 configuration.
Before you start
Note
For recommended torque vales for tightening each connector, see Torque valuessection.
Steps
1. Connect the front cables
30 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
Figure 13. IBBU 1+1+1 configuration
For information on the front cables see the The cables in the front cable setsection.
2. Tighten the cables
DN02207082terminator part
2 4 6 51 3
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
31 (33)
Typical BTS configurations
If you need 2+2+2 RF chaining, refer to RF chaining cabling list section.
3.2.3 IBBU 1+1+1 ROC configuration
Purpose
Diagram 1+1+1 ROC configuration for IBBU cabinet shows the unit positionsand cables in IBBU 1+1+1 ROC configuration.
Before you start
Note
For recommended torque vales for tightening each connector, see Torque valuessection.
Note
ROC configurations need 1-3 WPD units. WPDA/WPDB units are delivered withthe other units according to the configuration the customer ordered. AWPD unitis attached to a blanco panel, and therefore it can be installed in the same manner;fixing it to the cabinet core with 4 screws from its corners. To install a WPD unit,remove the blanco panel from the cabinet, and according to the desiredconfiguration, replace it by a WPD unit attached to a blanco panel.
Steps
1. Attach the WPD unit to the cabinet
AWPD unit is attached to a blanco panel, and therefore it can be installedin the same manner; fixing it to the cabinet core with 4 screws from itscorners.
2. Connect the front cables
32 (33) # Nokia CorporationNokia Proprietary and Confidential
dn03474536Issue 1 en
WCDMA BTS Rel1 HW configurations
Figure 14. 1+1+1 ROC configuration for IBBU cabinet
For information on the front cables see the The cables in the front cable setsection.
3. Tighten the cables
DN02207094terminator part
2 4 6 51 3
dn03474536Issue 1 en
# Nokia CorporationNokia Proprietary and Confidential
33 (33)
Typical BTS configurations