Upload
oswald-dalton
View
224
Download
1
Embed Size (px)
Citation preview
1
Detectors
RIT Course Number 1051-465Lecture N: Lecture Title
2
Section Title Slide
3
pn Junction Review
• PN junctions are fabricated from a monocrystalline piece of semiconductor with both a P-type and N-type region in proximity at a junction.
• The transfer of electrons from the N side of the junction to holes annihilated on the P side of the junction produces a barrier voltage. This is 0.6 to 0.7 V in silicon, and varies with other semiconductors.
• A forward biased PN junction conducts a current once the barrier voltage is overcome. The external applied potential forces majority carriers toward the junction where recombinetion takes place, allowing current flow.
• A reverse biased PN junction conducts almost no current. The applied reverse bias attracts majority carriers away from the junction. This increases the thickness of the nonconducting depletion region.
• Reverse biased PN junctions show a temperature dependent reverse leakage current. This is less than a µA in small silicon diodes.
4
N-type
5
Band Diagram: Acceptor Dopant in Semiconductor
• For Si, add a group III element to “accept” an electron and make p-type Si (more positive “holes”).
• “Missing” electron results in an extra “hole”, with an acceptor energy level EA just above the valence band EV.
– Holes easily formed in valence band, greatly increasing the electrical conductivity.
• Fermi level EF moves down towards EV.
EA
EC
EV
EF
p-type Si
6
P-type
7
Conduction in p/n-type Semiconductors
8
9
PN Junction: Band Diagram
• Due to diffusion, electrons move from n to p-side and holes from p to n-side.
• Causes depletion zone at junction where immobile charged ion cores remain.
• Results in a built-in electric field (103 to 105 V/cm), which opposes further diffusion.
• Note: EF levels are aligned across pn junction under equilibrium.
Depletion Zone
electrons
pn regions in equilibrium
holesEV
EF
EC
EF
EV
EF
EC
+++
++++
++++
+––––
––––
––––
p-type
n-type
10
PN Junction: Band Diagram under Bias
• Forward Bias: negative voltage on n-side promotes diffusion of electrons by decreasing built-in junction potential higher current.
• Reverse Bias: positive voltage on n-side inhibits diffusion of electrons by increasing built-in junction potential lower current.
Minority Carriers
Forward Bias Reverse BiasEquilibrium
e–e– e–
Majority Carriers
p-type n-type p-type n-type p-type n-type
–V +V
11
Forward & Reverse Biased
12
PN Junction: IV Characteristics
• Current-Voltage Relationship
• Forward Bias: current exponentially increases.
• Reverse Bias: low leakage current equal to ~Io.
• Ability of pn junction to pass current in only one direction is known as “rectifying” behavior.
/[ 1]eV kToI I e
Reverse Bias
ForwardBias
13
• Current-Voltage Relationship
• Forward Bias: current exponentially increases.
• Reverse Bias: low leakage current equal to ~Io.
• Ability of pn junction to pass current in only one direction is known as “rectifying” behavior.
/[ 1]eV kToI I e
PN Junction: IV Characteristics
14
Doped Silicon
15
Suitable doped silicon bandgaps for detectors
16
Generation & Recombination
• In intrinsic semiconductor– n = p = ni
• ni is strongly temperature dependent• This is because at a give temperature
– Recombination of electrons (ri)= thermal generation rate (gi)
• ri = Bnp = gi (= Bni**2 for intrinsic semiconductor)
17
Photon induced excess carriers
18
Photon induced excess carriers
19
Photon induced excess carriers
20
xx
21
xx
22
xx
23
xx
24
Rate of change of carrier concentration
25
26
27
Diffusion
28
29
30
31
32
PN Junction
33
PN Junction
34
35
36
37
Put it all together …
38
Steps
• PN junction is reversed biased. • Shutter opened and photon enters semiconductor• Interacts with lattice generates minority carrier• Minority carrier diffuses till it reaches vicinity of junction• Junction field drives minority carrier across junction and discharges junction capacitance• At the end of some integration time measure voltage (V2)across junction.• Reset junction voltage to initial reverse bias value and measure its value (V1).• Difference in voltage is proportional to signal.
ΔQ = C1(V1-Vbi) * (V1-vbi) – C2(V2-Vbi) * (V2-Vbi)
39
Designing a junction
40
Dark Signal
41
Slide Title
• xxxxxx
42
Section Title Slide
43
Slide Title
• xxxxxx
44
Section Title Slide
45
Slide Title
• xxxxxx