1E115408#1

115408

W a l l C l o c k w i t h o u t H a n d s

Content

Qty Dimensions (mm) Designation Part no.

Plywood 2 300x210x3 Casing 1

Round beermat 3 ø 107 Dials 2

Grey cardboard 2 210x300x1 Dials 3

Quartz clock movement, right-turning 1 Wandstärke: 5 Clockwork 4

Metal set of hands 1 35/25 Top part, clockwork 5

Spacer sleeves 4 10 Spacers 6

Nuts 4 20x3 Screw connection 7

Cylinder head bolts 4 M3 Screw connection 8

Please Note The OPITEC range of projects is not intended as play toys for

young children. They are teaching aids for young people learning the skills of Craft, Design and Technology. These

projects should only be undertaken and operated with the guidance of a fully qualified adult. The finished projects are

not suitable to give to children under 3 years old. Some parts can be swallowed. Danger of suffocation!

Tools required: Fretsaw or scroll saw Drills, ø 2, ø 3, ø 4.5 ø 6.5 mm Pencil, ruler, protractor Open-jaw wrench Sandpaper Craft knife/scissors

2 E115408#2

Ø 3 Ø 10Ø 3

Ø 3Ø 3Ø 10

Ø 10Ø 3

Ø 4,5

Ø 6,5

Ø 168

Ø 115

Ø 168

Instructions

1. Choose your favourite motif and a matching layout template from pages (5 - 12). Transfer the layout template (pages 11-13) on to the plywood (1). For variation 1 both supplied wooden panels will be needed for a front and back panel. In order to be able to saw the two recesses, drill a ø 2mm hole on the cutting lines and feed the blade of your fretsaw through it. Then saw a recess and clean up the edges with sandpaper. Drill a ø 3mm hole. To make sure that the dril-lings are in registry with each other, put both front and back panels on top of each other and stabilise. Also drill a ø 10mm hole for the clock-work. (only back panel!) For the shelf clock transfer the foot rests 2x on to the remaining plywood and saw out. Clean up the sawed edges.

Front panel variation 1

Back panel variation 1

Foot rest variation 1

Front panel variation 2

Back panel variation 2

Foot rest variation 2

The clock without hands offers many design possibilities. Variation 1 shows the construction of a round wall clock, which can also be assembled as a shelf clock. We supply 5 different motif templates to choose from for variation 1. Variation 2 shows the construction of a shelf clock in the shape of an hourglass. Of course you can use your own designs as well for making these clocks. The instructions below cover the construction of both variations.

2x

2x

2. Insert the quartz clock movement from the back through the ø10mm drilled hole as shown and fasten with a nut at the front (see drawing variation 1 & 2)

Variation 1Variation 2

Beermat (2)

Cardboard (3a)

3. Variation 1: use the template (pages 17/19) and trace the circle (3a) ø 168 mm and the correspon-ding ring (3b) on to the cardboard. Cut out with a craft knife or a pair of scissors. Drill the centre hole ø 6,5mm through the cardboard circle ø 168mm. Mark the centre of the beermat (2) and drill a ø 4,5mm hole.Cardboard (3b)

Variation 1

3E115408#1

910

11121

24 5 6 7

83 55

5045

40

353025

2015

10

5 0

Ø 6,5

Ø 107

Ø 4,5

Ø 7

3

Ø 1

07

Ø 69

910

1112

1 2 3 4

56

7

8

55

50 45 40

3530

25

2015105

0

2x1x

(2b)

3a

3b

2

2a

2b

2b

2c

Instructions

3a) Cut out the dials for the wall clock or the shelf clock (round) from page 15.

3b) Variation 2: take the three beermats (2). Mark the centre point on one of them and drill a ø 6,5mm hole. Cut two rings from the other two beermats, following the template (page 14). Cut a ø 69 mm circle from one of the beermat cut-offs and mark the centre point. Drill a ø 4,5mm hole.

5. For both variations 1 und 2 cut off the hands from the hand mechanisms (5) as shown. Only the eyelets that held the hands remains. Glue the eyelet with the bigger hole to the back of the big dial (3a respectively 2a). Glue the eyelet with the small hole to the back of the small dial (2 respectively 2c). This step is not absolutely neces-sary. The hands can also be glued to the back uncut.

Cut off here Cut off here

6. Put the finished hour dial as well as the minute dial on the correct shaft of the quartz clock movement (4) (see drawing variation 1+2). Place the dials in such a way, that the 12 and the 0 are in the top position.

3c) Cut out the two dials from page 14.

4. For both variations glue the pieces to-gether as shown. Make sure that the edges are glued together well. For variation 1 glue part 3b to part 3a. For variation 2 glue the two beermat rings (2b) together and then stick them to part 2a.

Beermat (2a) Beermat (2c)

Variation 1 Variation 2

Variation 1 Variation 2

4 E115408#2

Instructions

7. Choose one of the motives and copy it on to the front panel. We recommend you paint the front panel before assembling it. Acrylic paint is best for colouring in the panel.

8. Insert the four cylinder head screws (7) from the front through the ø 3mm hole. Add a spacer sleeve (6) to each of the screws and stick the screws with the spacer sleeves into the ø 3mm hole in the back panel as shown.

9. Screw the four nuts (8) from the back on to the cylinder head screws (7) and tighten.

10. For the shelf clock version of the clock without hands glue the foot rests on as shown.

11. Insert battery (1,5 V Mignon) and use the small wheel on the clockwork to adjust the time. If this isn’t enough, move the respective dials! The number in the top recess shows the hours. The minutes show in the lower recess.

5E115408#1

InstructionsTemplate motif 1 Scale 1:1

6 E115408#2

InstructionsTemplate motif 2 Scale 1:1

7E115408#1

InstructionsTemplate motif 3 Scale 1:1

8 E115408#2

InstructionsTemplate motif 4 Scale 1:1

9E115408#1

InstructionsTemplate motif 5 Scale 1:1

10 E115408#2

InstructionsTemplate shelf clock motif hourglass Scale 1:1

11E115408#1

Ø 3

InstructionsSchablone Wanduhr rund Frontplatte M 1:1

12 E115408#2

Ø 3

Ø 3

Ø 10

Instructions

Template shelf clock Front panel Scale 1:1

Template shelf clock Back panel Scale 1:1

Template shelf clock Footrest Scale 1:1

2x cut out

13E115408#1

Ø 10Ø 3

Ø 10Ø 3 Ø 10

Ø 3

InstructionsTemplate wall clock Back panel Scale 1:1

Template wall clock Footrest Scale 1:1

14 E115408#2

910

11121

24 5 6 7

83 55

5045

40

353025

2015

105 0

Ø 6,5

Ø 107

Ø 4,5

Ø 7

3

Ø 1

07

Ø 69

InstructionsTemplate dials Shelf clock Scale 1:1

2x cut out

1x cut out

Template dials Shelf clock Scale 1:1

15E115408#1

910

111212

34 5 6 7

8

55

5045

40

353025

2015

10

5 0

InstructionsTemplate dials Wall clock round Scale 1:1

16 E115408#2

17E115408#1

Ø 115

Ø 168

InstructionsTemplate wall clock round Cardboard rings Scale 1:1

18 E115408#2

19E115408#1

Ø 4,5

Ø 6,5

Ø 168

InstructionsTemplate wall clock round Cardboard Scale 1:1

Template wall clock round Beermat Scale 1:1