4-in-1 SuperSeat®

Sit, Snack & Play!

INSTRUCTION MANUAL

Thank you for purchasing the 4-in-1 SuperSeat from Summer Infant. This multi-use seat is designed to grow with your little one from approximately 4 months

to approximately 4 years of age, providing a safe place to sit, snack and play!

13360/13365Please read the following instructions and warnings carefully

KEEP THIS INSTRUCTION MANUALFOR FUTURE REFERENCE.

Tool required: Phillips head screwdriver (not included).For technical support, contact us at (401) 671-6551.

or www.summerinfant.com/contactFor use with children from

approximately 4 months to 4 years (see page 8).Adult assembly required.

WARNING

2

FALL HAZARD: Infants have suffered skull fractures falling while in and from floor seats:· Use ONLY on the floor.· NEVER use on an elevated surface.· ALWAYS use restraints. Adjust to fit snugly.· NEVER lift or carry child in the product.· Use ONLY with a child that is able to hold their head up unassisted.· STOP using when child can climb out or walk.· ALWAYS keep child in view while in product.· NEVER use the toybar to lift or carry product with child in it.DROWNING HAZARD: Infants have drowned when floor seat has been placed in a bath tub or pool.· NEVER use in or near water.

Children have suffered head injuries, including skull fractures, after falling with or from booster seats.· Check that booster seat is securely attached to adult chair before each use.· Always use restraint until child is able to get in and out of booster seat without help. Adjust to fit snugly.· Never allow child to push away from table.· Never lift and carry child in booster seat.· Stay near and watch your child during use.· ALWAYS secure BOTH back and seat straps to an adult chair.· NEVER lift this product with your child in it.· NEVER leave child unattended and without supervision.· Prevent serious injury or death. Do not use in motor vehicles. · NEVER use this product as a car seat or bath seat, on a table or counter top, stool, swivel chair, folding chair, unstable chair or any chair where the straps cannot secure it properly.

· Minimum dimensions of adult chair that the booster seat shall be attached to: Seat width 18 in. and depth 18 in., and the seat backrest height is at least 8 in. tall.

· ALWAYS use product with plastic support insert securely installed, during all modes of use (as shown on page 8).· Until child is able to get in and out of the booster seat without help (about 2½ years old), the child should be secured in the booster seat at all times by the restraining system. The tray is not designed to hold the child in the chair.

· Use this product only with children capable of sitting upright unassisted.· Check that both the floor and seat of the chair are level before installing the booster seat.· Prevent finger injury: Keep child away from chair when installing the tray.· When in booster seat mode, use only feeding tray section and remove activity tray sections.· Once installed, check the security and position of the booster seat.· Do not use this booster unless all components are correctly fitted and adjusted.· Discontinue use of the product if damaged, broken, or disassembled.PREVENT FALLS: ALWAYS USE ADULT CHAIR STRAPS when using product on elevated surfaces as a booster seat.

Infant Floor/Support Seat Use:

Booster Seat Use:

WARNING

C

D

E

L

I

J K M

A

Seat BaseA

Fabric Seat B

Track Toy

I

C Support Insert

Plastic Support Insert

Backrest

D

Spinner Ball Tray

E

Shape Sorter Toys (2)

J

Center Tray

F

Feeding Tray

H Shape Sorter Tray

G

Clip Toys (2)

K

L

Adult Chair Straps (4)M

Long Screws (6)N

O Short Screws (4)

B

components:

assembly:

click!

click!

Press the

backrest

down into the

seat base.

It will lock

into place.

1 3

HF G

Activity Tray:

Hardware:

Note: Toddlers may not need the support insert. Remove insert from straps if desired.

Note: Ensure backrest and seat base are fully connected. Test stability and connection points before use.

!

!

Seat Base will come preassembled with: Child Restraint Straps, Fabric Seat, Plastic Support Insert, and Support Insert.

x6 x4

N O

assembly (continued):

Align the 2 screw holes in the

plastic support insert to the

those in the front base. Using

2 long screws, attach from the

underside of the base.

x 2

2

34

Flip the seat over.

Insert and fasten

the 4 long screws.

N

x 4

Helpful Hint: If possible, use a long screw-driver on the two front screw locations.

!Note: Bottom front T-straps will be attached prior to first use. To re-attach fabric seat if you need to remove and machine wash it, rethread T-straps through the slots.

!

N

x 2

Helpful Hint: This step may be easiest with the seat flipped over. You may need to pull the fabric back slightly to access the screw holes.

!

assembly (continued):

5

Thread the three

T-straps on the back of the

fabric seat into the slots on

the backrest.

4

5

Insert the four plastic fasteners

into the keyhole slots on the front of the

seat frame. Slide fasteners to lock.

x 2

Insert the two plastic fasteners

on the underside of the

fabric seat into the

top of the seat frame.

x 2

6

x 3

Note: Pull up to ensure the straps are fully inserted. They should not pull out of the slots.

!

x 2

assembly (continued):

Slide activity

tray into

track around

the backrest.Connect track toy (I)

by inserting it

onto the activity tray.

Use 4 short screws

to assemble the

activity tray (F,G,H).

press!press!

9

7

6

O

x 4

8

H

G

F

assembly (continued):

7

Connect feeding tray

to activity tray.

Clip toys (L)

onto loops on

each side of

the track toy.

click!

x 2

Note: It may help to place one hand on the back of the activity tray. Pull on all sides of the tray to ensure that it is fully connected.

click!

!

FINISHED!

Connect the square and

triangle sorter toys (K)

by threading the T-straps

through the slots

in the activity tray.

11

10

12

Note: Pull up to ensure the straps are fully inserted. They should not pull out of the slots.

!

modes of use:

Positioner/Support Seat Activity Center

Feeding SeatUse on the floor or on an adult chair

(chair straps included).

Booster SeatUse on an adult chair (chair straps included).

Fabric insert supports baby’s waist & back. Use for babies just learning to sit up unassisted.

360º rotating tray allows easy transition between feeding and activity time. Activity tray features

shape sorters, track toy with glider beads, spinner ball & lock and key teethers.

43

21

8

WARNING When seat is used on adult chair, use only the feeding tray. Remove the activity tray sections.

!

Only use for children who are able to hold their head up unassisted (approximately 4 months of age). Stop using as a Positioner/Support Seat and Activity Seat when child can walk or get in and out of product by themselves (approximately 12 months of age).

!

Only use for children capable of sitting upright unassisted. !

Pull the

lever beneath

the feeding tray

to release.

remove tray:

attach to adult chair:

9

x 4

LThread the

adult chair straps (L)

into the slots on the

underside of the

seat base.

1

Note: Pull up to ensure the straps are fully inserted. They should not pull out of the slots.

!

attach to adult chair (continued):

storing adult chair straps:

child restraint:

be sure to

tighten straps!

fasten clips

around

chair back and

underneath chair

seat!

press in

to release

Once fully assembled,

a storage pocket is located

underneath the front of the seat.

This pocket is used to store

the adult chair straps.

Coil straps and insert.

Never use on an adult chair without securely fastening chair straps. Always tighten adult chair straps and test security before use.

IMPORTANT

10

2

Insert. Press to

release.

removing fabric seat:

Remove the feeding

and activity trays.

11

x 3

Pull up the

two fasteners

on the underside

of the fabric seat

by lifting them up

and out from the

seat base.Remove the

four fasteners

from the keyhole

slots on the front

of the seat base

by sliding out.

x 2 x 2

1

4

32

Remove the

three T-straps from the

slots on the backrest.

x 2

Please retain informationfor future reference.

Colors and styles may vary.

MADE IN CHINA.7/18

Summer Infant (USA), Inc.1275 Park East DriveWoonsocket, RI 02895 USA 401-671-6551© 2018 Summer Infant (USA), Inc.

removing fabric seat (continued):

cleaning & maintenance:

• Fabric Seat & Support Insert: Machine wash, cold water, gentle cycle, no bleach. Tumble dry, low heat.• Wipe frame with a damp cloth and mild soap.• Do not use if any components are damaged missing, broken, or disassembled.

5 6

Remove the

two T-straps from the

slots underneath

the seat.Remove insert &

fabric seat

from restraint

straps.

x 2

We’re here to help! If you have questions or need assistance,please contact our Consumer Relations Team at401-671-6551 or www.summerinfant.com/contact