Upload
hazmi-hanif
View
218
Download
0
Embed Size (px)
Citation preview
8/18/2019 136 Sandblasting Cabinet (1)
1/2
MASTSAFE WORK PROCEDURE
Division: Analysis By: Date: Sep/12/2006
Department: Supervisor: Frequency: Hourly
Job Title: Auto Body Metl Approved By: JSA Number:
Job Title: S!d"l#t$!% C"$!et Job Performed By: Te&'er !d or #tude!t#
RE(U)RED PERSO*A+ PROTECT),E E(U)PME*T- CSA approved safety bootss!oes" CSA approved safety #lasses#o##les"!earin# protection" $%%& cotton coveralls
.E*ERA+ *OTES- 'perators must be trained by a teac!er" demonstrate competency and receive pre(approval to operate t!isequipment" by t!e teac!ers of t!e Auto Body )etal s!op or Automotive Tec!nolo#y s!op*
No matc!es" li#!ters or cell p!ones allo+ed in t!e s!op area* ,on# !air s!ould be tied bac-. strin#s and !oods from pulloverss+eaterss!ould be removed or tuc-ed inside of coveralls* ,on# nec-laces and or bracelets s!ould be removed*
OB SAFET A*A+S)S-
Step De#&r$pt$o! Hrd Co!trol#
$ Pre(operation +al- around inspection ofsand(((blaster and surroundin# area*((Sandblaster side door s+in# s!ould beclear of obstructions* /nsure t!at t!e
side door closes properly and t!at t!elatc! secures door ti#!t*
a0 'peration in1urin# yourself or ((b0'peration in1urin# ot!ers((c0 Sliparound mac!ine area*
a0 2 b0 3emove any obstructive material fromdoor s+in# area*((c0 Clean up sand from 4oorarea to reduce slippa#e*((/nsure t!at t!eequipment is not dama#e ( if dama#ed do not
use" notify teac!er ri#!t a+ay*
5 a0 C!ec- for e6!aust fan operation* 78nt!e Auto Tec!nolo#y s!op you mustattac! an e6!aust !ose to t!e !ose of t!esand blaster0*((B0 C!ec- for cabinet li#!toperation*((c0 C!ec- #lass for abrasiveareas*((
a0 Dust in!alation((b0 9isibility a0 Contact a teac!er immediately if e6!aust fanfails to start(up*((b0 Contact teac!er and reportan inoperative interior li#!t*((c0 8f t!e cabinetinspection #lass !as been eroded" as- a teac!erto assist +it! its replacement or as- teac!er to!ave it replaced*
a0 'pen doors and inspect door seals*((b08nspect bead #un for proper #roundin#*((c0 8nspect #loves to ma-e sure t!ey arenot torn or ripped*
a0 ,ea-a#e onto 4oor ( slips((b0/lectrical static s!oc-((c0 Sandpenetratin# s-in ( abrasion
a0 3eseal lea-in# door((b0 3epair #round onbead #un((c0 3eplace #loves((
Pa#e $ of 5 Print Date: Sep$55%%;
8/18/2019 136 Sandblasting Cabinet (1)
2/2
< 8f sandblaster passes all inspections andeveryt!in# is in #ood +or-in# order* ((Turnon li#!t" ensure bot! doors are sealed andsecure" place !ands in #loves !old bead#un +it! one !and and +it! t!e ot!er!and !old +!at you are blastin#* Pressdo+n on foot pedal +it! foot" a mi6ture of air and sand +ill be forced t!rou#! t!e
bead #un* Continue sandblastin# untilyou are satis=ed" 1ob completed*
Doors not sealed and secured ( dustin!alation" lea-a#e onto 4oor ( slips*
)a-e sure doors are sealed and secure*
> 3emove foot from foot pedal" and +aituntil dust !as settled before openin# topdoor or side door to remove your +or-*'nce +or- is removed" re(latc! doors*((S!ut o? li#!t" 7disconnect e6!aust !ose(auto tec! only0* Clean up any sand t!at!as fallen around sandblaster*
Dust in!alation((Slip around mac!inearea
@ait until dust !as settled before removin# your+or-*((Clean up area of any sand t!at !as fallenaround sandblaster*
AUTHOR)ED EMP+OEE )*FORMAT)O*-
)D *UMBER- +AST *AME- F)RST *AME- REMARKS-
OB H)STOR )*FORMAT)O*-
DATE- REMARKS-
Approval Si#nature: Date:
Pa#e 5 of 5 Print Date: Sep$55%%;