Upload
hoanghanh
View
230
Download
4
Embed Size (px)
Citation preview
SDC application - commissioning
This manual serves as a guide for uploading SDC applications to your phone, tablet or computer. The manual is for those who ask for remote assistance Somfy or your distributor.
These instructions will lead you with commissioning of SDC application that will control RTS receivers via RS485 RTS transmitter. This system allows you to control RTS motors over the Internet.
2
SDC application - Youtube links
You can watch content of this manual on Youtube channel SomfyCZ (with subtitles):
1. iRidium Client installation -http://www.youtube.com/watch?v=UTGhOyYArF4
2. iRidium Transfer installation -http://www.youtube.com/watch?v=jfxZFW-6LKc
3. licence and device test -http://www.youtube.com/watch?v=AX2ahPSw4HI
Settings manual:1. communication -
http://www.youtube.com/watch?v=MOz-hmDhBv02. Sonnese motors, timers and control panel -
http://www.youtube.com/watch?v=tR5yjLVcOUs3. channels and groups and RS485 RTS transmitter -
http://www.youtube.com/watch?v=eTU0EtoXsVs3
Content
1. Installation
2. Downloading i2 Control into your smart device
3. Transfer project to your device
4. Router configuration
5. Contact
4
SDC application - installation
For controlling RTS receivers over the Internet you need:� RS485 RTS transmitter� LAN (WiFi) / RS485 interface� iRidium mobile licence
You can receive demo licences from iRidium mobile for free.
6
iRidium mobile for free.
.
Connect RS485 RTS transmitter and LAN / RS485 interface with 2(3) wire cable - this will be RS485 bus.
SDC application - installation
These 2 connected devices can be displayed in this scheme:
7
In case of WiFi / RS485 interface then no cable is needed between the interface and the router.
This scheme allows to control the installation in one moment only from one smart device.
SDC application - installation
Following instruction describes how to install SDC application into your smart device. Somfy SDC application is used for control:
� RTS motors or motors with RTS receivers� Sonnese RS485 motors� ILT2 motors connected to RS485 4ILT interface� RS485 motor controllers� IB+ motor controllers
8
� IB+ motor controllers
Somfy SDC application was developed on iRidium Mobile console. Therefore, first you have to install iRidium client application into your device. Then you can upload SDC applications into iRidium client using iRidiumTransfer SW.
SDC application - installation
The installation will be divided into the following steps:1. upload iRidium client application to your device2. setting IP addresses of WiFi (LAN) / RS485 converter
9
SDC application - iRidium client
Selecting iRidium client application depends on the type of used smart devices:
� iPad / iPhoneinstall i2 control from Apple Store
� Mac OS Xinstall iM
� Android phone / tablet
11
� Android phone / tabletinstall i2 control from Google Play
� PC with Windowsinstall Iridium client app (in case you will need also software Iridium Gate
for concurrent access of more smart devices then download full SW package for PC)
All links are available on http://www.iridiummobile.net/ in DOWNLOAD section. You have to register before you are allowed to download.
SDC application - iRidium client
In case that your smart Android device didn´t find i2 control on Google play, then you should download *.apk file from www.iridiummobile.net.
12
Instructions how to install SDC application you can find also on SomfyCZ Youtube channel.
This manual covers also problematic HTC phones.
SDC aplikace - iRidium client
Open the app i2 control. You can see the following screen. Hold for 10 seconds finger on the screen until appears to you requirement to enter a password. Enter the password 2007. For Windows request to get the password display by pressing F8.
13
SDC aplikace - menu iRidium client
Copy HWID number and send it to Somfy or your distributor together with the requirement of the type of license (demo or commerciallicense).
14
SDC aplikace - menu iRidium client
You will get from Somfy or distributor an IP address that you insert into the green box. Make sure that you have the Update ON and Update Now to YES. Then press Apply and you will download the application SDC.
15
SDC application - Somfy demo board
You can try SDC application on Somfy demo board via the Internet. Just enter IP address of our public Internet connection 46.13.164.254 (in case of a problem with the connection, contact Somfy by email [email protected] or phone +420267910007 to check this IP address).
If you download SDC app from web site www.somfyarchitecture.cz, then the correct IP address is set within SDC app.
16
You can watch a reaction on your orders. Just type the following address into an internet browser: http://sdcapplication.click2stream.com/
Then you can watch a reaction on your orders sent from your device thanks to the installed IP camera. Count with 3 sec delay. Be patient because this page is very slow.
SDC application - IP addresses
Set IP address of your LAN(WiFi)/RS485 interface in SDC app. Probably you have the interface set to receive IP address from the router that is connected to. In this case you can use free software Advance IP scanner (http://www.advanced-ip-scanner.com/), that can find the interface´s IP address.
17
As the 2nd IP address set your public IP address. In case you don´t have a permanent IP address from your Internet provider then it can happen that this IP address will be changed in the future.
SDC application - router setting
To have access from the Internet, the router must be set to forward port 4999 to the IP address of LAN (WiFi) / RS485 interface or IP address of PC with running iRidium Gate. Next you have to forward port 4998 to the IP address of LAN (WiFi) / RS485 interface.
Then you enter public IP address to your smart device. It is adviced to set permanent IP addresses for used devices.
18
SDC application - IP addresses scheme
Final scheme:
IP address accessible from the Internet, ie. 46.13.164.254
insert public IP address visible from the Internet side, ie. 46.13.164.254
search for IP address obtained by the router,ie. 192.168.1.4
19
PC IP address will be ie. 192.168.1.10; in iRidium Gate fill IP address LAN/RS 485 interface -ie.192.168.1.4
pozn.: in case of only short bus wiring, you don´t need to use resistors at the ends
forward a communication of port 4999 to the IP address of PC, ie. 192.168.1.10
SDC application - LAN(WiFi)/RS485 interface setting
If SDC application controls IB+ motor controllers, some parameters of LAN/RS485 interface have to be changed.
enter correct IP address of your interface
20
port number
serial net setting
SDC application - LAN(WiFi)/RS485 interface setting
Serial NET settings in the interface:
21
In case you purchase an interface from Somfy, it is set for usage with Somfy RS485 products. If you want to use IB+ motor controllers, you need to change these settings.
SDC application contact
In case of any questions use the contact below:
Tomáš Veselý[email protected]. +420 733 683 351
22