18 Watt Stout Parts

You can scroll through the images above using the Image scroll controls or you can use the Left and Right

arrow keys on your keyboard.

18 Watt stout with Hot switch.

This is not a kit, it is a parts listing from my project build.

Back to library page

Qty Description of part

1 Suitable Chassis of your choice - I do not stock a small Stout chassis.

Back panel parts

1 rotary impedance selector switch

1 Knob of your choice

2 #11 jacks speaker jacks

1 12 Foot Power cord

Ads by a2zLyrics Ad Options

Ads by a2zLyrics Ad Options

18 Watt Stout Parts http://www.el34world.com/projects/18WattStoutParts.htm

1 de 4 11/10/2013 11:17 p.m.

1 180 Ohm LED current limiting resistor

2 Knobs of your choice

2 pots 2 x 500KA

1 12A input jack

1 SPST mini toggle switch - relay only

Top chassis parts

4 9 pin tube sockets that fits your chassis

2 12AX7 pre amp tubes

2 EL84 power tubes

2 EL84 spring clips

1 8 pin tube socket that fits your chassis - rectifier tube

1 5Y3 Rectifier Tube

1 Sovtek tube spring retainer - rectifier tube

1 18 Watt power tranny with 5 volt tap

1 18 Watt output tranny with 4, 8 and 16 ohm taps

Off board 1/2 watt resistors

2 100 ohm - heater center tap

1 100K - pots

2 8.2K - El84 grid stoppers

1 1M - input jack

Off board misc.

1 125C3A choke

1 40x20x20x20 filter cap

1 40x20x20x20 cap clamp

5 ft Each Red, Black, White, Green 20GA Solid core wire or cloth wire

5 ft 18 Gauge Heater wire or cloth wire

5 ft Mini shielded cable if shielding is needed.

6 #8 Ring terminals

6 inches Heat shrink tubing

1 6 Lug terminal strip

Assortment of #4, #6 and #8 screws, nuts and washers, depending on what you are mounting.

Get 20 of each to have on hand.

Circuit board 1/2 watt resistors

1 820 OHM

2 2.2K

1 47K

4 100K

5 47OK

Circuit board 3 watt resistors

1 4.7K

1 10K


2 de 4 11/10/2013 11:17 p.m.

2 .01 Mallory 150 - 400 volt or higher

4 .022 Mallory 150 - 400 volt or higher

1 .68/250V

1 47uf/100v cathode cap

Circuit board misc.

4 1/4" Nylon standoffs

4 #8 x 5/8" screws

4 #8 Nuts

1 1/8" Thick circuit board x 7.25 inches long

44 Turret lugs - 52 if you are doing relay switching

On board Relay stuff

1 Relay socket

1 5 volt signal switching relay

1 1N4001 or 1N4007 Diode

Relay power supply board

1 Bridge #1 - See my web catalog

2 4700uf/16V caps

1 1/2 watt dropping resistor - 100 ohm will work

1 1/8" Thick circuit board x 1.5" wide x 3" long

7 Turret lugs

Home - Ordering Information - PayPal info - Returning parts - Search the Hoffman Amps parts catalog -

Links

Shipping Info/policy - E-mail Me - Amplifier Service Technicians - About Hoffman Amps

Sound Clips - LED Bike light build info - Guitar Rig and Behringer FCB1010 info

The Tube amp Library of information - Charts - Diagrams - How To's - ProjectsClick the link above for Tube amp info, Schematics, Board building information, Projects, Mods, Transformer

diagrams, Photo's, Sound clips.

There are hundreds of pages of Tube amp information on my library page.

Check out our huge library of Tube Amp Schematics here

Please visit my Tube Amplifier ForumHere's the place you can go to ask tube amplifier questions.

You will find a large community of friendly amp builders at the link above.

MEMBER OF PROJECT HONEY POTSpam Harvester Protection Network

provided by Unspam@


3 de 4 11/10/2013 11:17 p.m.


4 de 4 11/10/2013 11:17 p.m.

Documents

18 Watt Stout Parts