Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
TYLDEN HERITAGE R MODEL MACK
MAIL ORDER PARTS
CATALOGUE Custom Classic Truck & Tractor Restorations
Business Hours: 0428 507 408
Location: 1906 Trentham Road, Kyneton Vic 3444 Australia
Note: Our workshop & warehouse are only open by appointment
Postal Address: P.O. Box 614, Kyneton Vic 3444 Australia
Supplier of after market Mack reproduction and dress up parts
Big range of Mack ‘B’ & “R” Model bits. Special Interest in:
Mack Trucks...........Diamond T Trucks......Caterpillar Tractors Trading since 1961
Email: [email protected] web: www.tyldenheritage.com.au
Lee No 3 Pty Ltd – A.C.N. 005 204 599 A.B.N. 40 005 204 599 These pages may only be reproduced after obtaining written permission from Tylden Heritage.
All rights reserved.
COST PER PRINTED CATALOGUE INCL POSTAGE $10
1956 Mack LTL Diesel
INDEX FOR R MACK PARTS
1R. AXLE: Section 1
CHASSIS: Section 1. Bumper, Fuel Tank, Mudflaps, Steering, Tail Shaft. ENGINE: Section 1: Radiator, Starter Motor. 2R BONNET Section 2: Latches, JEWELLERY: Dogs, Emblems. 3R CABIN INTERIOR: Section 3. 4R CABIN EXTERIOR: Section 4. 5R DOOR PARTS: Section 5.
SEE GENERAL SECTION CATALOGUE FOR OTHER PART OPTIONS
- Parts for Axle, Brakes, Catches, Dress Up, Electrical, Parts Books, Rubber Parts, Reproduction Cast Parts, Steel Name Plates & Instruction Plates & Stickers.
20/09/2016
SECTION 1---- R SERIES MACK PARTSALL PRICES ARE SUBJECT TO GST
E9 MOTOR - 2 AVAILABLEMack E9 - 450 complete motor. Governed at 1800RPM. 4
Valve Serial No SK0280. Built new 1/3/85. Clutch CL795. -
2 available.
15,000.00$
12 SPEED GEAR BOX - EX ABOVEMack TRTXL 1070B 12 speed gear box. Serial No. 5K0892 5,000.00$
REAR AXLE COMPLETE ASSEMBLYRear axle air bag Mack SA38C Carrier CRDPC92 CRD93
Ratio 3.87 Spacing bogie 60 inches.
6,500.00$
NOTE: ABOVE PARTS BUILTThe above parts came from a Superliner 11 to give truck a
required speed of 75 mph = 120Km per hour at 1800 rpm.
SLEEPER BOX60 inch sleeper box. Has been stripped out inside. Came
from US built Superliner, has V type opening and comes
with cabin cut out if required.
3,000.00$
R CABINS - PAINT STRIPPEDR Model cabin, hand stripped back to gal finish - no rust.
Ready for painting inside and out.
6,500.00$
R CABIN COMPLETE - WHITER Model cabin complete as lifted out of classic. Very good
condition and would not require painting if used for work
truck.
8,500.00$
NEW MACK BUMPERSSuit new Superliner, Titan bumper, complete mounting kit
with front under protection. (FUP).
1,000.00$
R MODEL FIBREGLASS BONNETR Model fibreglass bonnet. Does not include grille. 750.00$
EARLY 'R' DOOR - LIKE NEWEarly door, complete with early type door lock & window
winder. Ex USA fire trucks.
1,500.00$
R MODEL-1 AXLE
20/09/2016
SECTION 1---- R SERIES MACK PARTSALL PRICES ARE SUBJECT TO GST
CHASSIS PARTS
R MODEL DIFFSingle axle diff hub to hub ex R model - ratio 4.25 with
springs.
$ 2,000.00
AXLE HUB - MODERN CONVERSIONAxle wheel hubs for conversion to 10 stud USA from Spider.
Suit 44000lbs diff. Made in USA. NEW. Price Per Each.
Mack Part No MK3398HR735K
$ 635.00
Brake drum for 2947. NEW. Price Per Each. $ 120.00
BUMPER BARR Model standard bumper bar - black. New. Made in USA POA
R Model standard bumper bar - chrome. New. Weight 25kg.
Length 2450mm, height 450mm. Flanges are 90mm.
$ 1,950.00
BUMPS STOP SPRINGFront spring buffer, suit R, flat top 2 1/4 high, 2 1/8 diam,
3/4 long X 3/8 locating bolt...See Rubber Parts General
Section 6G-6 for pricing and options
BATTERY BOX.Heavy duty Mack battery box base with ribbed top - 2
sections. New. Note: we can supply lid chrome plated.
380.00$
Heavy duty Mack type battery box, bottom section holds 2
batteries with rubber latch/catch- as on R model - new.
Note: we can supply chrome catch for B Model.
$ 263.90
R MODEL-1 AXLE
20/09/2016
SECTION 1---- R SERIES MACK PARTS
CHASSIS PARTSALL PRICES ARE SUBJECT TO GST
BATTERY BOX. (cont)Black steel ribbed top battery box lid cover - correct for R
model - NEW. Note: we can supply lid chrome plated.
$ 145.60
Steel battery hold down bracket, hold the batteries securely -
not stocked.
$ 81.90
Nickel Cadium carriage bolt. Holds batteries bracket down -
2 required (sold as a kit)- not stocked
$ 10.00
ELEPHANT SPRING INSULATOR FEETTop insulator, suit 44000. 4 Required. Price Per Each. SEE
RUBBER PARTS IN GENERAL SECTION 6G-19 FOR
PRICING.
Top insulator suit 34-38000 steel base, 6ins x 4 1/2 ins 1
3/4 dowl. 4 Required. Price Per Each. SEE RUBBER
PARTS IN GENERAL SECTION 6G-19 FOR PRICING
Lower insulator. Suit 34-38 & 44000 rear end. Steel Base 6
1/8 x 6 1/8 1 3/4 dowl. 4 Required. Price Per Each.SEE
RUBBER PARTS IN GENERAL SECTION 6G-19 FOR
PRICING.
Side spacer of lower insulator Neoprene. 8 Required. Price
Per Each. SEE RUBBER PARTS IN GENERAL SECTION
6G-19 FOR PRICING.
MUD FLAPSMack facing dog. SEE RUBBER PARTS IN GENERAL
SECTION 6G-18 FOR PRICING AND OPTIONS.
FUEL TANK J BRACKET ROLLED EDGE
STRAPRubber Fuel Tank Strap - 2 inch. Comes in bag of 25ft.
(7.6M) SEE RUBBER PARTS IN GENERAL SECTION 6G-
20 FOR PRICING AND OTHER OPTIONS.
R MODEL-1 AXLE
20/09/2016
SECTION 1---- R SERIES MACK PARTS
ALL PRICES ARE SUBJECT TO GST
R MODEL FUEL TANK FLAT STRAPR Mack flat fuel tank strap. 2 1/8 wide 1/8 thick (has no
edge turn up). Sold Per Foot. SEE GENERAL SECTION 6G-
20 FOR PRICING & OPTIONS
FRONT FUEL TANK SUPPORT RUBBERSR fuel tanks per each. 3 3/4 in long x 2 5/8 diam x 1 1/2
hole are split for fitting. SEE GENERAL SECION 6G-20
FOR PRICING & OPTIONS.
STEERING PARTS
BEARINGR Bearing Steering Shaft. Size shaft 1 inch OD 2 inch. $ 75.00
R Bearing Steering Shaft Firewall. Size shaft 1 inch hole,
centres 3 1/2 inch.
$ 82.00
DUST COVERR Rubber dust boot steering shaft 1 inch (25mm) round
hole. See Rubber Parts in General Section 6G-5 for pricing
and options.
$ 14.50
R Rubber dust boot slip yoke 4 slots to suit shaft. See
General Section 6G-5 for pricing & options.
SHAFTShaft steering lower - suit Superliner 2 and other models $ 250.00
Shaft steering main - suit Superliner 2 over all length 46
inches (1070mm) as in photo thats with 6 inch (150mm)
inside yoke
$ 510.00
R STEERING
YOKEYoke. Steering Shaft Ross Box. (.875 inch ID) . Bin 3091 $ 65.00
R MODEL-1 AXLE
20/09/2016
SECTION 1---- R SERIES MACK PARTSALL PRICES ARE SUBJECT TO GST
ENGINEAir starter motor used. Note: Pinion lengths vary. 400.00$
Air starter valve remote valve assembly. NEW $ 279.00
12V air starter solonoid control valve - to suit 3179. NEW $ 206.00
AIR INTAKE FITTINGSAir Hose hump connector, straight, suit 5 inch tube. Suit
Superliner. SEE GENERAL RUBBER SECTION 6G-16
FOR COST & OPTIONS
Air hose connector, straight, suit 6 inch tube. SEE
GENERAL RUBBER SECTION 6G-16 FOR COST &
OPTIONS
Air elbow 38 deg. Suit 5 inch tube. SEE GENERAL
RUBBERS SECTION 6G-16 FOR COST & OPTIONS
Air elbow 38deg. Suit 6inch tube. Suit Superliner. SEE
GENERAL RUBBER SECTION 6G-16 FOR COST &
OPTIONS
Air elbow 90 deg suit 5 inch tube. SEE GENERAL RUBBER
SECTION 6G-16 FOR COST & OPTIONS
Air elbow 90 deg suit 6 inch tube. SEE GENERAL
RUBBER SECTION 6G-16 FOR COST & OPTIONS
INTERCOOLER CLAMPSpring loaded inter cooler clamps - 5 inch. SEE GENERAL
SECTION 6C-2 FOR COST & OPTIONS
Spring loaded inter coller clamp - 6 inch. SEE GENERAL
SECTION 6C-2 FOR COST & OPTIONS
R MODEL-1 AXLE
20/09/2016
SECTION 1---- R SERIES MACK PARTSALL PRICES ARE SUBJECT TO GST
ENGINE PARTS - 6 CYLINDER
WATER PUMP KIT
Suit most 60's & 70's Macks 5/8 shaft. (Note: shaft lengths
do vary with number of pulleys and front bearing sizes may
vary also)
130.00$
WATER PUMP PARTS E9 V8Water Pump Kit - 9 Pieces. NOTE: This kit bushes need
reaming after fitting.
550.00$
Water pump, complete new unit 1,300.00$
Water pump seal only, suit above kit suit 3/4 shaft 1 5/8
OD. Suit E9. Bin 3106
60.00$
LUBERFINEREngine oil filter Luberfiner. Length15 inches (380mm)
diameter 7 1/2 inches (190mm). Suit 675 and other similar
build engines
120.00$
E9 EXHAUSTGasket Exhaust E9. 3.5/8 bolt. Centres 21/2 x 2 1/2
hole..PER EACH
37.00$
Oil Ring Turbo Oil Drain 3.00$
Gasket Ring Exhaust - PER EACH 50.00$
Oil Drain Gasket 1 inch hole. 2 1/16 bolt holes 8.45$
Turbo gasket. 33.00$
Oil Drain Gasket. 1/2 inch hole. 1 1/2 inch bolt holes. 5.00$
R MODEL-1 AXLE
20/09/2016
SECTION 1---- R SERIES MACK PARTSALL PRICES ARE SUBJECT TO GST
E 9 PARTS (CONT)
DRAG LINK COVERSDrag link leather grease covers with lace - new. See
Rubber Parts in General Section 6G-13 for pricing.
POWER STEERINGOriginal power assist booster type steering kit - Used (note:
pump not included) as taken off used trucks. See engine
parts in next section for pump options.
$ 2,750.00
POWER STEERING PUMPGenerator with regulator and power steering drive type and
oil pump as fitted to B & early R Models with power assist
optional steering from new
$ 445.00
DRIVE COUPLINGRubber Drive coupling for power steering pump of
Generator. B & early R models. (as above)..Bin 131
$ 100.00
POWER STEERING PUMP V8Power Steering pump with drive - suit 864 V8 - Used $ 500.00
SECTION 1---- R SERIES MACK PARTSALL PRICES ARE SUBJECT TO GST
ENGINE
BELT DRIVEPower Steering pump -Belt drive $ 250.00
Power Steering Pump Bracket $ 100.00
R MODEL-1 AXLE
20/09/2016
R MODEL ENGINE MOUNTING INSULATORS
Mack engine mounting rubber. Fits some Flintstones, R
Model, V/Liner, Superliner, Ultraliner, Cruiseliner etc from
about 70's to around 1990's where they run 8 rear engine
mounts, also used as front engine mount on some models.
Note: Very common engine mounts. Size of 2745 & 2747
80mmx20mmdeep with 50mm wide and 18mm hgh centre.
Number depending on model. 8 required for most models. 8
standard mounts. Price per each.
22.50$
Top harder rubber yellow dot used on rear top mount. 4 per
truck. Price per each
30.45$
ENGINE PLATESMack engine exhaust emission control information rocker
cover plate. 200mm long x 70mm high. Supplied blank for
your detail. See General Section 6I-2 for price & options.
MACK GENERAL MODELS ( Photocopy)Workshop Manual - 937 Pages - Early - Covers Models B67-
673-70. Includes Mack C.M.B.F.R.U & Flintstone - For
Engines END 465 - END 673 - ENDT 673 - ENDT673 & B -
END 711 - END 864 - ENDT 864. Fuel pump, clutch, gear
box, drive shaft, diffs, came with our first new R Model Mack
in 1976
$ 138.00
MACK R WORKSHOP MANUAL (Photocopy)
Workshop Manual - covers R-RD-U & DM models - 338
Pages. Chassis, cooling, front axle, steering, springs, &
suspension, wheels, brakes, electrical. Cabs. This book
came with our first new R model Mack in 1976
$ 91.00
R MODEL-1 AXLE
20/09/2016
R MODEL - SECTION 2
BONNETT, JEWELLERY, LATCHES
ALL PRICES ARE SUBJECT TO GST
BONNET LATCH SHORT TYPE - STEEL BONNET
3290 R Model black hood latch with square body - New - 4 required per
truck - Note: bottom pin needs turning for some models - sold per
each - catch is extra. Square tube section 3 1/2 inch x 90mm long
$ 81.90
3291 R Model black hood catch for above– NEW – Price Per Each. $ 25.00
OPTIONAL CHROME- SHORT TYPE3292 Model R chrome hood latch with square body - new. Sold per
each. Note: Catch is extra. Square tube section 3 1/2 inch x
90mm long
$ 200.00
3293 Model R chrome hood latch for above - new. Suit 3292. Bin 3297 $ 40.00
MODEL R HOOD LATCH3294 Model R hood latch socket - NEW not painted. Bin 3293 $ 24.50
USED BLACK SHORT TYPE3295 Used R Model black short square - some rust. Used. $ 40.00
BONNET LATCH - LONG TYPE - FIBREGLASS
BONNET 3296 Latch - R model chrome fibreglass hood (bonnet) 8 inch (200mm)
pin centres with adjustable length. Suit Superliner 11 &
Valveliner. Sold Per Each.
$ 92.00
3297 Latch - R Model black fibreglass hood (bonnet) 8inch (200mm) pin
centres. 2 Per Truck. Sold per Each. Square tube section 5 1/2
inch x 140mm long.
$ 70.00
BONNET LATCH SPRING - SHORT TYPE161 Replacement spring bonnet latch. 80mm long x 13mm wide -
Bin 141
$ 22.75
BONNET LATCH RUBBER3302 Long bonnet latch. Suit Superliner 2 and others. Length centre of
mounting pin to latch connecting point - 7 inch x 180mm overall
length 330mm x 13 inch.
$ 89.00
R MODEL-2 BONNET ETC
20/09/2016
R MODEL - SECTION 2
BONNETT, JEWELLERY, LATCHES
ALL PRICES ARE SUBJECT TO GST
SOCKET CLIP FOR 33023305 Clip for long rubber bonnet latch. Part No 3302. As fitted to
Superliner and Valveliner. PRICE PER EACH.
$ 38.50
3301 Short bonnet latch. Also suit battery box and some bonnets. PER
EACH. Length centre of mounting pin to latch connecting point 4
3/4 inch x 125mm.
$ 25.50
SOCKET CLIP FOR 33023299 Clip for short bonnet hatch. Bin 3301 $ 10.20
3260 Lower mounting kit for 3301 $ 11.00
BONNET WEAR STRAP3300 Nylon cabin to hood wear strap. R Model. PER EACH $ 31.00
BONNET HINGE3268 Bonnet hinge ball type $ 98.00
3269 Bonnet hinge pivot ball type. Suits R Model bonnet mount (with
front radiator mtg intercooler).
$ 120.00
R BONNET LOCATING ROLLERS3298 Bonnet locating rollers. 3 inch diam 2 3/8 wide, 5/8 hole $ 105.00
BONNET FLARES3273 R Model bonnet mudguard flares $ 599.00
BONNET BADGES
GRILLE FRONT LETTER SET - R MODEL3310 Mack letter set. Front. Suit R Bonnet (hood). NEW. Letter size- 5
1/2inch by 3 1/4 inch
$ 107.00
R MODEL-2 BONNET ETC
20/09/2016
R MODEL - SECTION 2
BONNETT, JEWELLERY, LATCHES, DOGS etc
ALL PRICES ARE SUBJECT TO GST
CABIN FRONT LETTER SET - F MODEL3312 Mack F letter set. Front of cabin. New. Letter size 2 inch high $ 98.00
SIDE SCRIPT3311 Mack script name - side 9inch x 3 inch. NEW. Sold Per Each. $ 48.00
BONNET BADGES3318 Econodyne Emblem - suit R Model - Price Per Each. Not stocked $ 115.00
3319 Maxidyne Emblem - suit R Model - not stocked POA
3321 Super liner emblem. Price per Each. NEW. $ 140.00
HALF DOG3322 Mack R - Half Dog - 2 per truck. L&R hand...NEW. Price Per
Each
$ 63.70
LATE MACK HALF DOG3270 New Mack logo standing half dog. Left and Right, facing each
other. Cast from brass, detailed and chrome plated. PRICE PER
SET OF 2 DOGS.
$ 170.00
MACK LETTER SET 3271 New Mack logo letters. Set of 4, cast from brass, detailed and
chrome plated. Price per Set of 8 letters. Bin 3270
$ 280.00
EARLY MACK DOG654A New old stock Mack long ear dogs, as fitted to Mack trucks 1932
to 1979.
$ 225.00
LATE MACK DOG3307 Late Mack Short Eared Dog. Standard bonnet size...NEW $ 159.00
DOG BASE3308 R Model base for Bulldog - chromed with special screws.NEW $ 50.00
R MODEL-2 BONNET ETC
20/09/2016
R MODEL - SECTION 2
BONNETT, JEWELLERY, LATCHES, DOGS etc
ALL PRICES ARE SUBJECT TO GST
REPRODUCTION MODEL BADGES3324 Mack R600 badge.Cast from Brass, Detailed & Chromed - length
210mm (8 1/4 inch)
$ 165.00
3325 Mack R700 Badge, Cast from Brass, Detailed & Chromed. Length
210mm (8 1/4 inch)
$ 165.00
3326 Mack F700 Badge. Cast from Brass, Detailed & Chromed. Length
210mm (8 1/4 inch)
$ 165.00
3327 Mack R800 badge. Cast from brass. Detailed & Chromed. Length
210mm (8 1/4 inch)
$ 175.00
3330 V8 Side Badge. Cast from Brass. Detailed & Chromed.
90mmx60x8 thick.
$ 165.00
BONNET BADGES
GRILLE 3303 Grille - Suit R & F - New or Used and Reconditioned. Price
subject to quality & stock. Priced on condition.
$ 1,000.00
FIBREGLASS GRILLE MOUNTING3304 New fibreglass mounting surround POA
GRILLE MOULDING3306 Grille surround moulding - black, in 2 sections. POA
3313 New Headlamp Assembly 12V. Fits most Macks with single round
headlight also other model trucks & cars. Supplied with lens body
and lead ready for fitting.
$ 85.00
3314 Headlamp Gasket for 3313 light assembly. $ 11.00
3317 Chrome head light bezel. Suits steel style fronts, R also DM,
Valueliner and Flintstone & B80 & 81 Tylden JR ute. Size rear ID
210mm front ID. 185mmx30mm deep. Sold Per each.
$ 103.00
R MODEL-2 BONNET ETC
20/09/2016
R MODEL - SECTION 2
BONNETT, JEWELLERY, LATCHES, DOGS etc
ALL PRICES ARE SUBJECT TO GST3316 Headlight Trim. New Stainless steel 16 5/8 long x 9 1/4 high. 7 3/8
inch hole. Price Per Each. NOTE: This type has only 2 bolt holes
and is a wee bit smaller than the 6 bolt hole one.
$ 99.00
HEADLIGHT BEZEL3332 Duel headlight bezel. Suit Superliner. 1 3/4 (45mm) deep with
mounting screws. PRICE PER EACH
$ 97.00
3333 Dual headlight bezel. Suit Superliner. 1 3/8 (35mm) with mounting
screws PRICE PER EACH
$ 130.00
HEADLIGHT ASSEMBLY3338 Complete oblong head light assembly RH (see part no 3332 for
chrome bezel)
$ 229.00
3339 Complete oblong head light assembly LH. (see part no 3332 for
chrome bezel)
$ 229.00
ROUND BLINKER (INDICATOR) LIGHTS772 Fender (mudguard) turn signal LED round face look a like 100mm
light with chrome bezel - amber both sides - suits B & R model &
other US built trucks - SOLD PER EACH SEE GENERAL 6E-1
FOR PRICING & OTHER OPTIONS
R TYPE SQUARE BLINKER3334 R Model double side square LED hood top mounting blinker lamp
includes wiring tail. NOTE: This light has built in side lamp so
3335 below would not be necessary. SEE GENERAL 6E-1 FOR
PRICING & OTHER OPTIONS
SUPERLINER STYLED DUAL FACE BLINKER3341 Combination turn signal, side marker & park light signal with round
lens. USA made, grey body with amber or amber and red main
lens. Replaceable globe 12V 2.1A 0.5 minor. 4 wires. Price Per
Each. SEE GENERAL 6E FOR PRICING & OTHER OPTIONS
ROUND BLINKER SIDE AMBER3335 R Model side hood blinker lamp assembly. - Amber with wiring.
SEE GENERAL 6E-1 FOR PRICING & OTHER OPTIONS.
PARK LIGHTS3336 Lamp Marker Park Light Assembly, clear with wiring. See General
Section 6E-7 for Pricing.
3337 Parking light lens only - clear or amber for above. 3335 & 3336.
See General Section 6E-7 for Pricing and options.
R MODEL-2 BONNET ETC
20/09/2016
R MODEL - SECTION 2
BONNETT, JEWELLERY, LATCHES, DOGS etc
ALL PRICES ARE SUBJECT TO GST
FRONT MUDFLAP3340 .Mudflap bonnet LH & RH R Model black with brass eyelets, not
Valveliner. See Rubber Parts in General Section 6G-18 for pricing
and options.
BONNET (HOOD) WEBBING2692 Suit Flintstone etc. - See Rubber in General Section 6G-4 for
Pricing and Options.
BONNET MOUNTING RUBBERS2746 Bonnet pivot mounting insulators. Supplied with 2 large lower & 2
small upper. Note: this part fits some R, V/Liner, S/Liner & early
Titans and cab and sleeper box mounts as well. Size 65x30 with
52x13 top. See Section 6G-3 for pricing.
2748 Lower bonnet mount size 52mmx13. See Rubber in General
Section 6G-3 for pricing and options.
R MODEL-2 BONNET ETC
20/09/2016
R MODEL - SECTION 3 - CABIN INTERIOR
ALL PRICES ARE SUBJECT TO GST
WESTERN TRIM3345 Tylden offer a full R Model Western Trim package as per factory
with large facing dogs or diamonds hot welded into material or
optional stitched with buttons. Available in brown, cream, grey,
magnum (red), or colour of your choice.
2,560.00$
Western Trim including 2 seats (part No 3347), 2 Door trims (Part
No 3348), Rear Cab (Part No 3349) and Hood Lining (Part No
3350). 2 Pillar Trims.
NOTE: ALL PRICES SHOWN ARE FOR UPHOLSTERY ONLY.
3347 Bucket Seats, original perforated vinyl with Mack Logo stamp (as
original) Price Per Each. Ask us to email better photos.
400.00$
3348 R Model Western door trim with welded dog logo. Original
welded patterns or stitched with buttons. Price Per Each. Ask us
to email better photos.
400.00$
3356 R Model door arm rest, included with 3348 OR Price Per Each.
Ask us to email better photos.
25.00$
3349 R Model rear Western original pattern cab lining in perforated
vinyl.
Ask us to email better quality photos.
475.00$
3350 R Model roof head lining in perforated vinyl.
Ask us to email better quality photos
475.00$
FOLLOWING NOT INCLUDED IN PART NO. 3345 PACKAGE
ABOVE PRICES
ROOF CONSOLE3351 R Model front roof console 160.00$
FLOOR CONSOLE3352 R Model centre floor console in vinyl and carpet, base & lid. - trim
only. Supplied by Customer. NOTE: Photos shows a special
one.
170.00$
ALL NEW FLOOR CONSOLE3357 Complete new centre console, 390mm long x 300mm deep x
280mm wide, folded from S/S with hinged marine ply. Lid
covered in vinyl with carpet kick strip on bottom with stamped
dog logo in lid. Photo show lid only.
290.00$
3356 Stainless steel centre console base, 390mm x300mm deep x 280
wide.
148.00$
R MODEL-3 CABIN INTERIOR
20/09/2016
R MODEL - SECTION 3 - CABIN INTERIOR
ALL PRICES ARE SUBJECT TO GST
CABIN SIDE INFILL3358 Cabin side kick infill same colour of interior. 98.00$
HATCH SURROUND3353 R Model hatch surround 55.00$
DOOR PILLAR3354 R Model Side front pillar trims - L & R at top of photo.
Centre of photo shows door arm rests - part 3356.
Bottom photo are angles to hold roof console part 3351.
Note: 3356 & 3351 are display only.
110.00$
DOG STAMP3365 Stamp your material with original dog type stamp PRICE PER
EACH.
45.00$
INTERIOR LIGHT3364 R Model dome interior light with switch and lead. 99.00$
DASH3412 Dash - new. Made from fibreglass POA
DASH PANEL LH3410 New R model genuine dash - left hand section. Including top
hatch.
1,385.00$
GLOVE BOX LID3413 New glove box lid to suit above 135.00$
DASH PANEL RH3411 New R model genuine dash - right hand section. 539.00$
3516 Dash Panel Screw. See door for nut. Bin 3540 3.00$
3519 Nut dash and door trim. Bin 3540. 3.00$
R MODEL-3 CABIN INTERIOR
20/09/2016
R MODEL - SECTION 3 - CABIN INTERIOR
ALL PRICES ARE SUBJECT TO GST
ENGINE STOP CABLE3359 R Model engine stop cable. Red Knob. 80.00$
HAND TROTTLE CABLE3360 R Model hand throttle cable. Black knob. 80.00$
STANDARD MATCHING GAUGES SUIT R & B MACK
SPEEDO3367 Speedo gauge. 0-120 kmh cable 3 1/4 diam. 200.00$
3368 R Model speedo cable with 2 types of adaptors -112 Length
3050mm
70.00$
TACHO3369 Tacho gauge. Zero to 3200 RPM with built in hour meter. 3 1/4
inch.
210.00$
3370 R Model Tacho cable with 3 types of adaptors. 2250mm long. 70.00$
MECHANICAL OIL PRESSURE GAUGE3372 Oil pressure gauge. 0 - 50 PSI mechanical. Suit 2 inch hole
mounting.
128.00$
LOW OIL PRESSURE SWITCH3373 Low oil pressure warning engine switch 51.00$
OIL TEMPERATURE GAUGE3378 Mack Gauge - Oil Temp. Engine, Transmission & Diff. 60 to 160
Cel.Bin 3373.
125.00$
3379 Mack Gauge - Oil Temperature Sender for 3378. Transmission &
Diff.
60.00$
R MODEL-3 CABIN INTERIOR
20/09/2016
R MODEL - SECTION 3 - CABIN INTERIOR
ALL PRICES ARE SUBJECT TO GST
VOLT METER3377 Mack Gauge Volt 12V 10 to 16amps battery condition and
charge section
110.00$
WATER TEMPERATURE GAUGE3380 Mack Gauge - Water Temp Neg 100-230 Fahrenheit 105.00$
3381 Mack Gauge - Water Temperture Sender Unit. Negative Ground.
Bin 3373
55.00$
AIR PRESSURE GAUGE3386 Mack Gauge - Air Pressure Dual needle 50mm diam. 1000KPA
1/8 - 27 NPTF.
140.00$
FUEL GAUGE3387 Fuel Gauge 105.00$
3388 Sender Fuel Gauge R & F multi volt. Suit tank 6-24 inch deep.
Suit Pal & Mack gauges. 250ohm empty 1020ohm half full &
31ohm full.
81.00$
TACKO WITH MACK LOGO1030 Tachometer head - black face with Mack logo. 0 to 3200 RPM
with engine hours. Cable operated. Suit 85mm diam hole.
$ 178.00
GAUGE INDENTIFICATION STICKER1281 Gauge face sticker for 1 and 2 diff, engine and oil temp. See
stickers in general section 6J-5 for pricing and options.
INDICATOR STALK - TURN SIGNAL771 R Series indicator stalk - 7 wires. See General Section 6E-1 for
pricing and options.
3383-8 R Series indicator stalk. - 8 Wires. See General Section 6E-1
for pricing and options.
R MODEL-3 CABIN INTERIOR
20/09/2016
R MODEL - SECTION 3 - CABIN INTERIOR
ALL PRICES ARE SUBJECT TO GST
DIP SWITCH3389 R Series dip switch with long or short leg. Bin 3377 55.00$
LOCK SET IGNITION & DOOR856 Lock Kit Ignition and door lock R & F . See General Section 6E-
2 for pricingBin 88
CUSTOM HORN BUTTON LOGO1258 Custom horn button logo with your Custom details. Mounted on
S/S plate for easy mounting on your horn button. See Stickers in
General Section for Pricing.
38.00$
FRONT FLOOR MAT3391 R Model front floor mat - moulded rubber ribbed with Mack logo
& wear section on LH side.
429.00$
REAR FLOOR MAT3392 R Model rear floor under seat mat - moulded ribbed rubber 200.00$
3393 R Model plain floor mat (no ribs etc) supplied in one section.
LOOSE FLOOR MAT2771 Floor mat - loose with dog logo with cut out for peddles. Sold as
Pair. The second (passenger side) one is square.
135.00$
R MODEL CLUTCH PEDAL3406 R Model clutch pedal & bracket clutch type. Generally stocked to
change from old through floor pedal type to pendulum type with
cable. Photo shows insulation in B Model. - Used
230.00$
CLUTCH CABLE3404 Suit R600 & Valveliner 109" (2770mm) 112" (2850mm) tip to tip. 144.00$
3403 Suit Trident, Titan, VL S/L, 138" (3480mm) long 220.00$
R MODEL-3 CABIN INTERIOR
20/09/2016
R MODEL - SECTION 3 - CABIN INTERIOR
ALL PRICES ARE SUBJECT TO GST
GEAR SHIFT BOOT2869 Gear shift boot - rubber - 180mm long x 100mm wide x 70mm
high. See General Section 6G-5 for pricing
2868 Stainless steel surround Cover for boot 2869. See General
Section Rubber 6G-5 for Pricing.
2870 Steering Column gear shift boot and rubber - 222mm long x
135mm wide x 70 high.See General Section 6G-5 for pricing
CLUTCH RUBBER2482 Clutch pedal - rubber replacement pad, also fits B Model. See
General Section 6G-1 for pricing.
R MODEL FOOT VALVE PEDAL3074 New brake pedal with Mack logo. Note holes are not drilled. See
General Section for other brake options.
78.00$
THROTTLE PEDAL361 R Model fuel pedal only with Mack logo - New. Price Per Each. 72.80$
KICK PLATES3415 R Door entry aluminium kick plates. Price Per Each. 45.00$
3414 R Model Entry Kick Plate. Custom Polished Stainless Steel. POA
HEATER DUCT3407 Round heater duct vents - suit R Model POA
3408 Oblong heater duct vents - suit R Model POA
R MODEL-3 CABIN INTERIOR
20/09/2016
R MODEL - SECTION 3 - CABIN INTERIOR
VINYL STICKERS - GENERAL
STEERING WHEEL3454 Mack optional upgrade. 18 inch 4 spoke steering wheel. See
General Section 6D for pricing.
POA
3455 Steering wheel hub for above to suit R model standard steering
shaft.
POA
MACK AIR ACTUATORY3405 Mack red dot part no 4379-RD554144 suit Mack CHR 1992 to
about 2000. Used to open and close air vent shutters.
60.00$
DRIVER INSTRUCTION STICKERSSEE GENERAL SECTION - 6J FOR OPTIONS
R SERIES MACK CAB STICKERS1236 WARNING TOWING. See Stickers General Section 6J-5 for
pricing
1237 COMPOUND TRANSFER CASE See Stickers General Section
6-5J for pricing
`
1241 MAXIDYNE OPERATING INSTRUCTIONS. See Stickers
General Section 6J-5 for pricing
1244 CAUTION T2090 TRANSMISSION. See Stickers General
Section 6J-5 for pricing
1246 STEERING LOCK ADJUST STICKER 60x30mm - SAMPLE
PHOTO See Stickers General Section 6J-5 for pricing
1274 DOOR ENTRY WARNING sticker 100x60mm. See General
Section 6J-5 for pricing
1280 HORN COVER LOGO. Rectangular horn cover 112mm long
56mm deep. Wording is 107mm long. See General Section 6J-5
for pricing
GAUGE INDENTIFICATION STICKER1281 Gauge face sticker for diff 1 & 2 gearbox and engine. See
General Section 6J-5 for pricing.
R MODEL-3 CABIN INTERIOR
20/09/2016
SECTION 4 - R MODEL CABIN EXTERIOR
ALL PRICES ARE SUBJECT TO GST
AIR CLEANER3460 Used RH Mack air cleaner (sample photo) POA
AIR CLEANER TOP HAT NUTS3190 Nut top of air cleaner. 24 in set. Price per each nut. $ 5.00
AIR CLEANER HAT3461 Air cleaner hat - black plastic 15in x 3 1/2 plus sprigit extra 1 1/2 ins
rain.
$ 140.00
AIR CLEANER SERVICE INSTRUCTIONS1276 Air Cleaner Service Instructuion for EBA15 as fitted to Superliner
and other models. 180mmx145
$ 20.00
AIR CLEANER ELEMENT INFORMATION1278 Air Cleaner Element Information Sticker. Length 120mmx70mm $ 15.00
AIR INTAKE FITTINGS2739 Air Hose hump connector, straight, suit 5 inch tube. Suit Superliner.
SEE GENERAL RUBBER SECTION 6G-1 FOR COST & OPTIONS
2742 Air hose connector, straight, suit 6 inch tube. SEE GENERAL
RUBBER SECTION 6G-16 FOR COST & OPTIONS
2740 Air elbow 38 deg. Suit 5 inch tube. SEE GENERAL RUBBERS
SECTION 6G-16 FOR COST & OPTIONS
2743 Air elbow 38deg. Suit 6inch tube. Suit Superliner. SEE GENERAL
RUBBER SECTION 6G-16 FOR COST & OPTIONS
2741 Air elbow 90 deg suit 5 inch tube. SEE GENERAL RUBBER
SECTION 6G-16 FOR COST & OPTIONS
2744 Air elbow 90 deg suit 6 inch tube. SEE GENERAL RUBBER
SECTION 6G-16 FOR COST & OPTIONS
Page 22 R MODEL-4 CABIN EXTERIOR
20/09/2016
SECTION 4 - R MODEL CABIN EXTERIOR
ALL PRICES ARE SUBJECT TO GST
AIR HORN - ROUND3439 Horn - Air - round trumpet kit. $ 141.00
AIR HORN - RECTANGULAR3440 Mack horn air rectangular - front with snow cover with mounting kit. $ 210.00
HORN COVER LOGO1280 Rectangular Horn Cover 115mm long 56mm deep. Wording is
110mm long.
$ 18.00
CABIN INSULATOR3434 Cab insulator R cabin. Also R fuel tanks per each. 3 3/4 in long x 2
5/8 diam x 1 1/2 hole are split for fitting.
$ 28.00
CAB ENTRY GRAB HANDLE3437 Grab entry handles. 23 long. Price Per Each. $ 78.00
CAB LEVELLING VALVE3467 Valve cab levelling suit R Model + T401 Kw. $ 148.00
CABIN SUPER CUSHION AIR BAG3468 Cabin rear air spring bag. Max inflation 100 PSI. Max Torque 15ft
lbs. Length 5 1/4 inch. Diameter at big end - 3 1/2 inch
$ 86.42
CABIN BULLET LIGHTS3444 Bullet type roof lights 390mm long x 90mm diam, supplied with
mounting bolts. See General Electrical Section 6E for pricing and
options.
3445 Bullet short centre light. 200mm long x 90mm diam. Price Per Each.
See General Electrical Section 6E for pricing and options.
ROUND BLINKER (INDICATOR) LIGHTS772 Fender (mudguard) turn signal LED round face look a like 100mm
light with chrome bezel - amber both sides - suits B & R model &
other US built trucks - SOLD PER EACH SEE GENERAL 6E FOR
PRICING & OTHER OPTIONS
Page 23 R MODEL-4 CABIN EXTERIOR
20/09/2016
SECTION 4 - R MODEL CABIN EXTERIOR
ALL PRICES ARE SUBJECT TO GST
R TYPE SQUARE BLINKER3334 R Model double side square LED hood top mounting blinker lamp
includes wiring tail. . (see Electrical in General Section 6E-1 for
pricing). NOTE: This light has built in side lamp so 3335 above
would not be necessary. SEE GENERAL 6E FOR PRICING &
OTHER OPTIONS
SUPERLINER STYLED BLINKER3341 Combination turn signal, side marker & park light signal. USA made,
grey body with amber or amber and red main lens. 4 wires. Price Per
Each. Extra 2 Amber lens. SEE GENERAL 6E-1 FOR PRICING &
OTHER OPTIONS
ROUND BLINKER SIDE AMBER3335 R Model side hood blinker lamp assembly. - Amber with wiring.
SEE GENERAL 6E-1 FOR PRICING & OTHER OPTIONS.
CABIN VENTS
TOP ROOF VENT3449 Cabin top roof vent cowl assembly $ 240.00
R MODEL CABIN ROOF VENT SEAL3420 Roof Vent Seal . 37 INCHES (940mm) $ 38.00
SIDE CABIN VENT3450 Side Vent Cover. $ 160.00
SIDE CABIN AIR VENT RUBBER2621 R Model side air vent sealing rubber. 10mmx8mm. 700mm (27 1/2
inches) per vent. SEE SECTION 6G-15 FOR PRICING
FRONT VENT OPENER OPTION 901 Optional front vent opener. Can be adapted to suit without a lot of
modification. 155mm closed 205mm open. Max load 125kg. Travel
speed 6mm per second. Has inbuilt limit switches supplied with 12V
switch.
$ 125.00
MIRROR - SEE DOORS NEXT SECTION
Page 24 R MODEL-4 CABIN EXTERIOR
20/09/2016
SECTION 4 - R MODEL CABIN EXTERIOR
ALL PRICES ARE SUBJECT TO GST
WINDSCREEN GLASS3416 Windscreen glass LHR, suit R. valve, super, metro. Weight 6Kg. 31
inches (800mm) x 21 inches (530mm).
$ 160.00
3417 Windscreen glass RHR, suit R, valve, super, metro. $ 160.00
R MODEL WINDSCREEN RUBBER3418 Windscreen rubber - complete both sides. $ 215.00
REAR WINDOW3430 R Model rear window - laminated. Tinted Std. Auto glass. $ 150.00
3432 Rear window rubber seal. $ 98.00
MIRROR
SEE DOOR PARTS - NEXT SECTION
R MODEL WIPER BLADE3497 Windscreen wiper blade. R Model. 16 inch long. $ 39.00
F MODEL WIPER BLADE3498 Windscreen wiper blade - F Model - 20 inch long (500mm) $ 58.00
R MODEL WIPER ARMS3495 LH wiper arm with inbuilt concealed windshield washer nozzles &
two knurled drive options.
$ 107.00
3496 RH Wiper arm with inbuilt concealed windshield washer nozzle and
two knurled drive options.
$ 107.00
WINDSCREEN BOTTLE3499 Reservoir windscreen washer bottle cap & pump. R model door. $ 125.00
3493 Washer bottle cap only $ 16.00
Page 25 R MODEL-4 CABIN EXTERIOR
20/09/2016
SECTION 4 - R MODEL CABIN EXTERIOR
ALL PRICES ARE SUBJECT TO GST
WINDSCREEN BOTTLE PUMP3494 Washer bottle pump $ 46.00
STEEL PLATE
FIREWALL PLATE1235 Blank Firewall certification plate (See General Section 6-3I for
pricing).
Page 26 R MODEL-4 CABIN EXTERIOR
20/09/2016
SECTION 5 - R MODEL - DOORS
ALL PRICES ARE SUBJECT TO GST3500 Door shell - R Model - new Left - suits 79 onwards door locks. $ 990.00
3501 Door shell - R Model. New right. Sit 79 onwards door locks. $ 990.00
3503 Door - R Model - Used. Ask re condition & price. Shell or
complete.
DOOR INNER PANEL3506 Door inner panel RH late bare - NEW $ 210.00
3516 Door panel screws. Price Per Each. Bin 2904 $ 3.00
2590 Door Panel J Nuts - 1/4 in thread. Bin 2907 $ 3.00
DOOR HANDLE3523 R door handle. Outer R & F model cb. $ 79.50
3524 R door handle inner R & F pre 79 NOTE: Part no. 3522 below has
better clearance.
$ 79.50
3522 R Model door handle late - inner R & F after 1979 with thicker
Western trim. NOTE: Later type, fits pre 79 door if you need better
clearance.
$ 70.00
3521 R Model door pull handle. Suit R, RB, RD, DM, MC, MR & LE.
R MODEL-5 DOORS
20/09/2016
SECTION 5 - R MODEL - DOORS
ALL PRICES ARE SUBJECT TO GST
PLEASE NOTE: DOOR PART CHANGES IN 1979
AND 1983,
DOOR HANDLE ESCUTCHEON3526 Handle escutcheon. Suit door and window crank handle. $ 9.90
3527 Pin Handle window & door. Suit door and window crank handle.
Bin 3526.
$ 2.15
QUARTER VENT WINDOW3528 Vent window flipper LH. (Quarter Vent), Suit models R & F. $ 275.00
3529 Vent window flipper RH. (Quarter Vent). Suit models R & F $ 275.00
GENUINE MACK SUPPLY3532 R model vent window flipper (quarter vent). LH only. Bin 3533 $ 356.00
3533 R model vent window flipper (quarter vent). RH only. $ 356.00
3571 R Model vent window flipper (quarter vent) outer rubber seal LH
only
$ 104.00
3572 R Model vent window flipper (quarter vent) outer rubber seal RH
only
$ 104.00
R MODEL DOOR GLASS3530 Door glass R & L. Note: We supply 6mm green tinted toughened
auto glass.
$ 102.00
R MODEL EARLY WINDOW REGULATOR89 Window regulator scissors - Left. Suit early R style cabs. $ 159.00
90 Window regulator scissors - Right. Suit early R style cabs. $ 159.00
R MODEL EARLY REGULATOR GEAR PLATE91 Gear plate for passenger side door regulator. Suit early style cabs. $ 149.00
92 Gear plate for driver side door regulator. Suit early styled cabs. $ 149.00
R MODEL-5 DOORS
20/09/2016
SECTION 5 - R MODEL - DOORS
ALL PRICES ARE SUBJECT TO GST
EARLY SIDE GLASS SUPPORT CHANNEL
PLEASE NOTE: DOOR PART CHANGES IN 1979
AND 1983,3566 Support channel for door glass regulator for passenger RHside roll
up window glass 400mm long. Used with Part 89 & 90. Suit early
styled cabs.
$ 53.50
3567 Support channel for door glass regulator for driver side LH roll up
window glass 400mm long. Suit early styled cabs.
$ 53.50
LATE MODEL WINDOW REGULATOR
3538 Regulator assembly LH. (Later model - post 83) $ 138.00
3539 Regulator assembly RH. (Later model - post 83). $ 138.00
3541 Screw for regulator assembly above. 4 Per Door. Price Per Each. $ 1.00
3540 Retaining ring for regulator to glass support track. Price Per Each.
(Suit 3538 & 3539) Bin 2914.
$ 3.60
3545 Linkage remote door. Connects handle to door lock. Used with
part No 3538 & 3539
$ 68.00
LATE MODEL WINDOW SUPPORT3535 Support window RH model. Used with Part 3538 - 450mm long. $ 89.00
3536 Support window LH model. Used with Part 3539. 450mm long. $ 89.00
WINDOW REGULATOR HANDLE3525 Window regulator handle, early R&F. See part no 3526 & 3527
for escutcheon & pin..page 2. Note Part No 3531 below has more
clearance.
$ 50.00
3531 Window regulator handle. Suit doors with Western Trim or worn
Shafts.
$ 72.00
R MODEL-5 DOORS
20/09/2016
SECTION 5 - R MODEL - DOORS
ALL PRICES ARE SUBJECT TO GST
PLEASE NOTE: DOOR PART CHANGES IN 1979
AND 1983,
DOOR LATCH EARLY TO 19793553 Latch door early RH, suit R & F, MIR, MBR $ 275.00
3554 Latch door - early LH. Suit R & F, MIR, MBR. $ 275.00
DOOR LATCH AFTER 1979 R & F3542 Latch door late RH. Used with part no. 3545. Mack current style
DM, R, RB, RD.
$ 84.00
3543 Latch door- late LH. Used with part no. 3545. Mack current style
DM, R, RB, RD.
$ 84.00
DOOR LATCH SCREWS3517 Door latch holding screws. 3 Per Door - 1/4 inch. PRICE PER
EACH..... Bin 2900
$ 1.82
DOOR STRIKER - EARLY R & F3555 Striker Plate - RH. Mack early style R, RB, RD, DM. $ 153.00
3556 Striker Plate - LH. Mack early style R, RB, RD, DM. $ 153.00
3559 Striker Plate RH - used with part no. 3560. Mack current style R,
RB, RD, DM.
$ 44.00
3560 Striker Plate LH. used with part no. 3560. Mack current style R,
RB, RD, DM.
$ 48.00
R MODEL-5 DOORS
20/09/2016
SECTION 5 -R MODEL - DOORS
ALL PRICES ARE SUBJECT TO GST
KEY DOOR LOCKS856 Door & ignition lock set, includes 2 door tumblers and one ignition
tumbler with 2 matching keys. New. SEE GENERAL SECTION
6E-2 FOR PRICING Bin 88
DOOR LOCK RETAINER CLIP2912 Door lock slide in retainer clip. Slides from outside inner door to
hold door lock in place. - New. Bin 2914
$ 11.50
BAILEY CHANNEL3549 Channel Bailey R&F. 2 per door. Price Per Each. Supplied with 5
clips. See Rubber Parts in General Section 6G-8 for Pricing.
WINDOW WEATHER FELT STRIP3550 Weather strip R & F model door glass sqeegee guides.- 1
required per door L & R. Price Per Each.see Rubber Parts in
General Section 6G-8 for Pricing.
WINDOW WEATHER STRIP WITH RUBBER SEAL
3546 Weather strip R&F model door glass squegee guides with rubber
wiper seal and door lip - RH (one per door)
$ 45.50
3547 Weather strip R&F model door glass squegee guides with rubber
wiper seal and door lip (one per door) - LH
$ 45.50
SPECIAL DOOR SEAL3558 Rubber super soft hollow door seal. Adhesive backing. Fits in
cabin door, closes against it.. 13mm wide 18mm high, sold in a
4.5m (15ft) length. See Rubber Parts in General Section 6G-9 for
Pricing.
MIRROR ARMS3575 Kit mirror bracket RH stainless. $ 204.00
3576 Kit mirror bracket LH stainless. $ 204.00
MIRROR HEAD3577 Mirror head-Mack. LH alloy type with bulldog but no heating or
light. See 803 General Electrical Section for light in photo
$ 229.00
3578 Mirror head-Mack. RH alloy type with bulldog but no heating or
light.
$ 229.00
R MODEL-5 DOORS