2009 Liberty 1st, Manual, de uso

LIBERTY 2009 owners manual

VEHICLES SOLD IN CANADA

With respect to any Vehicles Sold in Canada, the nameChrysler LLC shall be deemed to be deleted and thename Chrysler Canada Inc. used in substitution there-fore.DRIVING AND ALCOHOLDrunken driving is one of the most frequent causes ofaccidents.Your driving ability can be seriously impaired with bloodalcohol levels far below the legal minimum. If you aredrinking, dont drive. Ride with a designated non-drinkingdriver, call a cab, a friend, or use public transportation.

WARNING!

Driving after drinking can lead to an accident. Yourperceptions are less sharp, your reflexes are slower,and your judgment is impaired when you have beendrinking. Never drink and then drive.

This manual illustrates and describes the operation offeatures and equipment that are either standard or op-tional on this vehicle. This manual may also include adescription of features and equipment that are no longeravailable or were not ordered on this vehicle. Pleasedisregard any features and equipment described in thismanual that are not on this vehicle.

Chrysler LLC reserves the right to make changes indesign and specifications, and/or make additions to orimprovements to its products without imposing anyobligation upon itself to install them on products previ-ously manufactured.

Copyright 2008 Chrysler LLC

TABLE OF CONTENTSSECTION PAGE1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195

5 STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285

6 WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .391

7 MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405

8 MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451

9 IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .467

10 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477

1

2

3

4

5

6

7

8

9

10

INTRODUCTION

CONTENTS

m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

m Rollover Warning . . . . . . . . . . . . . . . . . . . . . . . . 4

m How To Use This Manual . . . . . . . . . . . . . . . . . . 5

m Warnings And Cautions . . . . . . . . . . . . . . . . . . . 7

m Vehicle Identification Number . . . . . . . . . . . . . . . 7

m Vehicle Modifications/Alterations . . . . . . . . . . . . 8

1

INTRODUCTIONThis Owners Manual has been prepared with the assis-tance of service and engineering specialists to acquaintyou with the operation and maintenance of your vehicle.It is supplemented by a Warranty Information Bookletand various customer-oriented documents. You areurged to read these publications carefully. Following theinstructions and recommendations in this manual willhelp assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be storedin the vehicle for convenient referencing and remainwith the vehicle when sold, so that the new owner willbe aware of all safety warnings.

When it comes to service, remember that your authorizeddealer knows your vehicle best, has the factory-trainedtechnicians and genuine Mopart parts, and is interestedin your satisfaction.

ROLLOVER WARNINGUtility vehicles have a significantly higher rollover ratethan other types of vehicles. This vehicle has a higherground clearance and a higher center of gravity thanmany passenger cars. It is capable of performing better ina wide variety of off-road applications. Driven in anunsafe manner, all vehicles can go out of control. Becauseof the higher center of gravity, if this vehicle is out ofcontrol it may roll over when some other vehicles maynot.

Do not attempt sharp turns, abrupt maneuvers, or otherunsafe driving actions that can cause loss of vehiclecontrol. Failure to operate this vehicle safely may resultin an accident, rollover of the vehicle, and severe or fatalinjury. Drive carefully.

4 INTRODUCTION

Failure to use driver and passenger seat belts providedis a major cause of severe or fatal injury. In fact, the U.S.government notes that the universal use of existing seat

belts could cut the highway death toll by 10,000 or moreeach year and could reduce disabling injuries by twomillion annually. In a rollover crash, an unbelted personis significantly more likely to die than a person wearinga seat belt. Always buckle up.

HOW TO USE THIS MANUALConsult the Table of Contents to determine which sectioncontains the information you desire.

The detailed index at the back of this Owners Manualcontains a complete listing of all subjects.

Consult the following table for a description of thesymbols that may be used on your vehicle or throughoutthis Owners Manual:

Rollover Warning Label

INTRODUCTION 5

1

6 INTRODUCTION

WARNINGS AND CAUTIONSThis Owners Manual contains WARNINGS against op-erating procedures that could result in an accident orbodily injury. It also contains CAUTIONS against proce-dures that could result in damage to your vehicle. If youdo not read this entire manual, you may miss importantinformation. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBERThe Vehicle Identification Number (VIN) is found on theleft front corner of the instrument panel. The VIN isvisible from outside of the vehicle through the wind-shield. This number also appears on the AutomobileInformation Disclosure Label affixed to a window onyour vehicle, the vehicle registration, and the title.

NOTE: It is illegal to remove the VIN.Vehicle Identification Number

INTRODUCTION 7

1

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle couldseriously affect its roadworthiness and safety andmay lead to an accident resulting in serious injury ordeath.

8 INTRODUCTION

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

m A Word About Your Keys . . . . . . . . . . . . . . . . . 12

Ignition Key Removal . . . . . . . . . . . . . . . . . . 12

Key-In-Ignition Reminder . . . . . . . . . . . . . . . . 14

m Sentry Keyt . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Replacement Keys . . . . . . . . . . . . . . . . . . . . . 16

Customer Key Programming . . . . . . . . . . . . . 16

General Information . . . . . . . . . . . . . . . . . . . . 17

m Vehicle Security Alarm System If Equipped . . 18

Rearming Of The System . . . . . . . . . . . . . . . . 18

To Arm The System . . . . . . . . . . . . . . . . . . . . 18

To Disarm The System . . . . . . . . . . . . . . . . . . 19

m Illuminated Entry System . . . . . . . . . . . . . . . . . 19

m Remote Keyless Entry (RKE) . . . . . . . . . . . . . . . 20

To Unlock The Doors And Liftgate . . . . . . . . . 20

To Lock The Doors And Liftgate . . . . . . . . . . . 22

To Unlatch The Liftgate Flip-Up Window . . . . . 23

Express Down Window Feature If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2

Using The Panic Alarm . . . . . . . . . . . . . . . . . 24

Programming Additional Transmitters . . . . . . . 25

Battery Replacement . . . . . . . . . . . . . . . . . . . 25

General Information . . . . . . . . . . . . . . . . . . . . 26

m Remote Starting System If Equipped . . . . . . . 27

How To Use Remote Start . . . . . . . . . . . . . . . 27

m Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Manual Door Locks . . . . . . . . . . . . . . . . . . . . 29

Power Door Locks . . . . . . . . . . . . . . . . . . . . . 30

Child-Protection Door Lock System(Rear Doors) . . . . . . . . . . . . . . . . . . . . . . . . . 33

m Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Power Windows . . . . . . . . . . . . . . . . . . . . . . 35

Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 39

m Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

m Occupant Restraints . . . . . . . . . . . . . . . . . . . . . 40

Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . 41

Lap/Shoulder Belt Untwisting Procedure . . . . . 47

Seat Belt Pretensioner If Present . . . . . . . . . 47

Enhanced Seat Belt Use Reminder System(BeltAlertt) . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Automatic Locking Mode If Equipped . . . . . 49

Energy Management Feature . . . . . . . . . . . . . 50

Seat Belts And Pregnant Women . . . . . . . . . . . 51

Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . 51

Driver And Front Passenger SupplementalRestraint System (SRS) - Airbag. . . . . . . . . . . . 52

Child Restraint . . . . . . . . . . . . . . . . . . . . . . . 70

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

m Engine Break-In Recommendations . . . . . . . . . . 80

m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Transporting Passengers . . . . . . . . . . . . . . . . . 80

Lock Your Vehicle . . . . . . . . . . . . . . . . . . . . . 81

Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . 81

Safety Checks You Should Make Inside TheVehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Periodic Safety Checks You Should MakeOutside The Vehicle . . . . . . . . . . . . . . . . . . . . 83

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11

2

A WORD ABOUT YOUR KEYSYou can insert the double-sided keys into the locks witheither side up.

The authorized dealer that sold you your new vehicle hasthe key code numbers for your vehicle locks. Thesenumbers can be used to order duplicate keys from yourauthorized dealer. Ask your authorized dealer for thesenumbers and keep them in a safe place.

Ignition Key RemovalAutomatic TransmissionPlace the shift lever in PARK. Turn the key to the ACCposition and then push the key and cylinder inwardslightly and rotate the key to the LOCK position. Thenremove the key.

Vehicle Key


NOTE: For vehicles not equipped with the Electronic Vehicle

Information Center (EVIC), features such as the powerwindow switches, radio, power sunroof or Sky Slidert(if equipped), and power outlets will remain active for45 seconds after the ignition switch is turned to theLOCK position. Opening either front door will cancelthis feature.

For vehicles equipped with the EVIC, features such asthe power window switches, radio, power sunroof orSky Slidert (if equipped), and power outlets willremain active for up to 10 minutes after the ignitionswitch is turned to the LOCK position. Opening eitherfront door will cancel this feature. The time for thisfeature is programmable. For details, refer to DelayPower Off to Accessories Until Exit, under PersonalSettings (Customer Programmable Features) underElectronic Vehicle Information Center (EVIC) inSection 4 of this manual.

Ignition Switch Positions

1 Lock 3 On2 Acc 4 Start


2

WARNING!

Never leave children alone in a vehicle. Leavingunattended children in a vehicle is dangerous for anumber of reasons. A child or others could be seri-ously or fatally injured. Dont leave the key in theignition. A child could operate power windows,other controls, or move the vehicle.

CAUTION!

An unlocked vehicle is an invitation to thieves.Always remove the key from the ignition, and lockall doors when leaving the vehicle unattended.

Key-In-Ignition ReminderIf you open the drivers door and the key is in theignition, a chime will sound to remind you to remove thekey.

NOTE: The Key-In-Ignition reminder only soundswhen the ignition key is placed in the LOCK or ACCposition.

SENTRY KEYTThe Sentry Keyt Immobilizer System prevents unautho-rized vehicle operation by disabling the engine. Thesystem does not need to be armed or activated. Operationis automatic, regardless of whether the vehicle is lockedor unlocked.

The system uses ignition keys that have an embeddedelectronic chip (transponder) to prevent unauthorizedvehicle operation. Therefore, only keys that are pro-grammed to the vehicle can be used to start and operatethe vehicle. The system will shut the engine off in twoseconds if someone uses an invalid key to try to start theengine.


NOTE: A key that has not been programmed is alsoconsidered an invalid key, even if it is cut to fit theignition switch lock cylinder for that vehicle.

During normal operation, after turning on the ignitionswitch, the Vehicle Security Light will turn on for threeseconds for a bulb check. If the light remains on after thebulb check, it indicates that there is a problem with theelectronics. In addition, if the Vehicle Security Lightbegins to flash after the bulb check, it indicates thatsomeone used an invalid key to try to start the engine.Either of these conditions will result in the engine beingshut off after two seconds.

If the Vehicle Security Light turns on during normalvehicle operation (vehicle running for longer than 10 sec-onds), it indicates that there is a fault in the electronics.Should this occur, have the vehicle serviced as soon aspossible.

NOTE: The Sentry Keyt Immobilizer System is not compat-

ible with some aftermarket remote starting systems.Use of these systems may result in vehicle startingproblems and loss of security protection.

Exxon/Mobil Speedpass, additional Sentry Keyst,or any other transponder-equipped components onthe same key chain will not cause a key-related(transponder) fault unless the additional part is physi-cally held against the ignition key being used whenstarting the vehicle. Cell phones, pagers, or otherRadio Frequency (RF) electronics will not cause inter-ference with this system.

All of the keys provided with your new vehicle havebeen programmed to the vehicle electronics.


2

Replacement KeysNOTE: Only keys that are programmed to the vehicleelectronics can be used to start and operate the vehicle.Once a Sentry Keyt is programmed to a vehicle, it cannotbe programmed to any other vehicle.

CAUTION!

Always remove the Sentry Keyst from the vehicleand lock all doors when leaving the vehicle unat-tended.

At the time of purchase, the original owner is providedwith a four-digit Personal Identification Number (PIN).Keep the PIN in a secure location. This number isrequired for authorized dealer replacement of keys. Du-plication of keys may be performed at an authorizeddealer or by following the customer key programming

procedure. This procedure consists of programming ablank key to the vehicle electronics. A blank key is onethat has never been programmed.

NOTE: When having the Sentry Keyt ImmobilizerSystem serviced, bring all vehicle keys with you to anauthorized dealer.

Customer Key ProgrammingIf you have two valid Sentry Keyst, you can programnew Sentry Keyst to the system by performing thefollowing procedure:

1. Cut the additional Sentry Keyt Transponder blank(s)to match the ignition switch lock cylinder key code.

2. Insert the first valid key into the ignition switch. Turnthe ignition switch to the ON position for at least threeseconds, but no longer than 15 seconds. Then, turn theignition switch to the LOCK position and remove the firstkey.


3. Insert the second valid key into the ignition switch.Turn the ignition switch to the ON position within15 seconds. After 10 seconds, a chime will sound. Inaddition, the Vehicle Security Light will begin to flash.Turn the ignition switch to the LOCK position andremove the second key.

4. Insert a blank Sentry Keyt into the ignition switch.Turn the ignition switch to the ON position within60 seconds. After 10 seconds, a single chime will sound.In addition, the Vehicle Security Light will stop flashing.To indicate that programming is complete, the VehicleSecurity Light will turn on again for three seconds andthen turn off.

The new Sentry Keyt is programmed. The RemoteKeyless Entry (RKE) transmitter will also be pro-grammed during this procedure.

Repeat this procedure to program up to eight keys. If youdo not have a programmed Sentry Keyt, contact yourauthorized dealer for details.

NOTE: If a programmed key is lost, see your authorizeddealer to have all remaining keys erased from the sys-tems memory. This will prevent the lost key from startingyour vehicle. The remaining keys must then be repro-grammed. All vehicle keys must be taken to an authorizeddealer at the time of service to be reprogrammed.

General InformationThe Sentry Keyt system complies with FCC rules Part 15and with RSS-210 of Industry Canada. Operation issubject to the following conditions:

This device may not cause harmful interference. This device must accept any interference that may be

received, including interference that may cause undes-ired operation.


2

VEHICLE SECURITY ALARM SYSTEM IFEQUIPPEDThe Vehicle Security Alarm system monitors the vehicledoors, liftgate, and liftgate flip-up window for unautho-rized entry and ignition for unauthorized operation.If something triggers the alarm, the system will soundthe horn intermittently, flash the headlights and tail-lights, and flash the Vehicle Security Light in the instru-ment cluster.NOTE: The Panic and Security alarms are quite differ-ent. Please take a moment to activate the Panic and theSecurity modes to hear the differences in the horn. In caseone should go off in the future, you will need to knowwhich mode has been activated in order to deactivate it.

Rearming of the System:If something triggers the Vehicle Security Alarm, and noaction is taken to disarm it, the system will turn off thehorn after three minutes, turn off all of the visual signalsafter 15 minutes, and then the system will rearm itself.

To Arm the System:1. Remove the key from the ignition switch and exit thevehicle.

2. Lock the doors and liftgate by pressing the power doorLOCK switch or the LOCK button on the Remote KeylessEntry (RKE) transmitter.

NOTE: The system will not arm if you lock the doorswith the manual door lock plungers or the drivers doorlock cylinder.

3. Close all doors. The Vehicle Security Light in theinstrument cluster will flash rapidly for about 16 secondsto signal that the system is arming. During this period,opening any door or the liftgate will cancel the armingprocess. If the system arms successfully, the VehicleSecurity Light will flash at a slower rate to indicate thealarm is set.


NOTE: For added security, whenever the SecurityAlarm is armed, the HomeLinkt/Garage Door Opener(if equipped) is disabled as well.

To Disarm the System:Either press the UNLOCK button on the RKE transmitteror insert a valid Sentry Keyt into the ignition lockcylinder and turn the key to the ON position.

NOTE: Unlocking the doors with the manual door lock plung-

ers or the drivers door lock cylinder will not disarmthe system.

When the system is armed, the interior power doorlock switches will not unlock the doors.

The Security Alarm System is designed to protect yourvehicle; however, you can create conditions where thesystem will give you a false alarm. If the previouslydescribed arming sequence has occurred, the system will

arm regardless of whether you are inside or outside thevehicle. If you remain inside the vehicle and open a door,the alarm will sound. If this occurs, disarm the system.

Tamper AlertIf something has triggered the Vehicle Security Alarm inyour absence, the horn will sound three times when youunlock the doors. Check the vehicle for tampering.

ILLUMINATED ENTRY SYSTEMThe interior lights will turn on when you use the RemoteKeyless Entry (RKE) transmitter or open a door.

This feature also turns on the approach lighting (if soequipped). For details, refer to Illumination Approach,under Personal Settings (Customer Programmable Fea-tures) under Electronic Vehicle Information Center(EVIC) in Section 4.


2

The interior lights will fade to off after about 30 secondsor they will immediately fade to off once the ignitionswitch is turned ON.

NOTE: The Illuminated Entry system will not operate the

interior lights if the dimmer control is in the extremedownward position.

REMOTE KEYLESS ENTRY (RKE)This system allows you to lock or unlock the doors andliftgate, open the liftgate flip-up window, or activate thePANIC alarm from distances up to 23 ft (7 m) using ahand-held Remote Keyless Entry (RKE) transmitter. TheRKE transmitter need not be pointed at the vehicle toactivate the system. However, the line of transmissionmust not be blocked with metal objects when using theRKE transmitter.

NOTE: Inserting the key into the ignition switch dis-ables all buttons on the RKE transmitter.

To Unlock the Doors and Liftgate:Press and release the UNLOCK button on the RKEtransmitter once to unlock the drivers door, or twice tounlock all doors and the liftgate. The turn signal lightswill flash to acknowledge the unlock signal. The illumi-nated entry system will also turn on.

Vehicle Key


Remote Key Unlock, Driver Door/All Doors FirstThis feature lets you program the system to unlock eitherthe drivers door or all doors and the liftgate on the firstpress of the UNLOCK button on the RKE transmitter. Tochange the current setting, proceed as follows:

For vehicles equipped with the Electronic VehicleInformation Center (EVIC), refer to Remote KeyUnlock, under Personal Settings (Customer Pro-grammable Features) under Electronic Vehicle Infor-mation Center (EVIC) in Section 4.

For vehicles not equipped with the EVIC, perform thefollowing steps:

1. Press and hold the LOCK button on a programmed(i.e., functional) RKE transmitter for at least 4 seconds,but no longer than 10 seconds. Then, press and hold theUNLOCK button while still holding the LOCK button.

2. Release both buttons at the same time.

3. Test the feature from outside the vehicle by pressingthe LOCK and UNLOCK buttons on the RKE transmitter.

4. Repeat these steps if you want to return this feature toits previous setting.

NOTE: Pressing the LOCK button on the RKE transmit-ter while you are inside the vehicle will activate theSecurity Alarm. Opening a door with the Security Alarmactivated will cause the alarm to sound. Press the UN-LOCK button to deactivate the Security Alarm.

Illuminated Approach If EquippedThis feature activates the headlights for up to 90 secondswhen the doors are unlocked with the RKE transmitter.The time for this feature is programmable on vehiclesequipped with the Electronic Vehicle Information Center(EVIC). For details, refer to Illumination Approach,under Personal Settings (Customer Programmable Fea-tures) under Electronic Vehicle Information Center(EVIC) in Section 4.


2

To Lock the Doors and Liftgate:Press and release the LOCK button on the RKE transmit-ter to lock all doors and the liftgate. The turn signal lightswill flash and the horn will chirp to acknowledge the locksignal.

Sound Horn with LockThis feature will cause the horn to chirp when the doorsare locked with the RKE transmitter. This feature can beturned on or turned off. To change the current setting,proceed as follows:

For vehicles equipped with the Electronic VehicleInformation Center (EVIC), refer to Sound Horn withRemote Key Lock, under Personal Settings (Cus-tomer Programmable Features) under Electronic Ve-hicle Information Center (EVIC) in Section 4.


1. Press the LOCK button on a programmed (i.e., func-tional) RKE transmitter for at least 4 seconds, but nolonger than 10 seconds. Then, press the PANIC buttonwhile still holding the LOCK button.


3. Test the feature from outside the vehicle by pressingthe LOCK button on the RKE transmitter.




Flash Lights with LockThe feature will cause the turn signal lights to flash whenthe doors are locked or unlocked with the RKE transmit-ter. This feature can be turned on or turned off. To changethe current setting, proceed as follows:

For vehicles equipped with the Electronic VehicleInformation Center (EVIC), refer to Flash Lights withRemote Key Lock, under 9Personal Settings (Cus-tomer Programmable Features) under Electronic Ve-hicle Information Center (EVIC) in Section 4.


1. Press and hold the UNLOCK button on a programmed(i.e., functional) RKE transmitter for at least 4 seconds,but no longer than 10 seconds. Then, press and hold theLOCK button while still holding the UNLOCK button.


3. Test the feature from outside the vehicle by pressingthe LOCK and UNLOCK buttons on the RKE transmitter.



To Unlatch the Liftgate Flip-Up Window:Press the REAR RELEASE button twice to unlatch theliftgate flip-up window.

WARNING!

To avoid injury stand back when opening. Glass willautomatically rise.


2

Express Down Window Feature If EquippedThis feature allows you to remotely lower both front doorwindows at the same time. To use this feature, press andrelease the UNLOCK button on the RKE transmitter andthen immediately press and hold the UNLOCK buttonuntil the windows lower to the level desired or until theylower completely.

Using the PANIC AlarmNOTE: The PANIC and Security Alarms are quitedifferent. Please take a moment to activate the PANICand the Security modes to hear the differences in thehorn. In case one should go off in the future, you willneed to know which mode has been activated in order todeactivate it.

To turn the PANIC Alarm feature ON or OFF, press andhold the PANIC button on the RKE transmitter for at

least one second and release. When the PANIC Alarm ison, the headlights and turn signal lights will flash, thehorn will pulse on and off, and the illuminated entrysystem will turn on.

The PANIC Alarm will stay on for three minutes unlessyou turn it off by pressing the PANIC button a secondtime or if the vehicle speed is 5 mph (8 km/h) or greater.

During the PANIC Mode, the door locks and RemoteKeyless Entry (RKE) system will function normally.PANIC mode will not disarm the Security System onvehicles so equipped.

NOTE: You may need to be close to the vehicle whenusing the RKE transmitter to turn off the PANIC Alarmdue to the radio frequency noises emitted by the system.


Programming Additional TransmittersRefer to SENTRY KEYt Customer Key Programmingin this section.

NOTE: If you do not have a programmed RKE trans-mitter, contact your authorized dealer for details.

Battery ReplacementThe recommended replacement battery is CR2032.

NOTE: Perchlorate Material special handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

Do not touch the battery terminals that are on the backhousing or the printed circuit board.

1. Remove the screw from the RKE transmitter case (ifequipped).

2. With the RKE transmitter buttons facing down, use aflat blade tool to pry the two halves of the RKE transmit-ter case apart. Make sure not to damage the seal duringremoval.

Separating Case Halves


2

3. Remove and replace the batteries. Avoid touching thenew batteries with your fingers. Skin oils may causebattery deterioration. If you touch a battery, clean it withrubbing alcohol.

4. To reassemble the RKE transmitter case, snap the twohalves together.

5. Reinstall and tighten the screw until snug (ifequipped).

General InformationThis device complies with Part 15 of FCC rules and withRS-210 of Industry Canada. Operation is subject to thefollowing conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference that may bereceived including interference that may cause undesiredoperation.

NOTE: Changes or modifications not expressly ap-proved by the party responsible for compliance couldvoid the users authority to operate the equipment.

If your RKE transmitter fails to operate from a normaldistance, check for these two conditions.

1. Weak batteries in RKE transmitter. The expected life ofthe batteries is from one to two years.

2. Closeness to a radio transmitter such as a radio stationtower, airport transmitter, and some mobile or CB radios.


REMOTE STARTING SYSTEM IF EQUIPPEDThis system uses the Remote Keyless Entry (RKE) trans-mitter to start the engine conveniently from outside thevehicle while still maintaining security. The system has atargeted range of 328 ft (100 m).

NOTE: The vehicle must be equipped with an auto-matic transmission to be equipped with Remote Start.

How To Use Remote StartAll of the following conditions must be met before theengine will remote start:

Shift lever in PARK. Doors closed. Hood closed. Liftgate closed. Hazard switch off. Brake switch inactive (brake pedal not pressed). Ignition key removed from ignition switch. Battery at an acceptable charge level. RKE PANIC button not pressed.

Remote Start Button


2

To Enter Remote Start ModePress and release the REMOTE START buttonon the RKE transmitter twice. The engine willstart and the vehicle will remain in the RemoteStart mode for a 15-minute cycle.

NOTE: For security, power window operation and sunroof or

Sky Slidert operation (if equipped) is disabled whenthe vehicle is in the Remote Start mode.

The engine can be started two consecutive times (two15-minute cycles) with the RKE transmitter. However,the ignition switch must be cycled to the ON positionbefore you can repeat the start sequence for a thirdcycle.

To Exit Remote Start Mode without Driving theVehicleAllow the engine to run for the entire 15-minute cycle.

To Exit Remote Start Mode and Drive the VehicleBefore the end of the 15-minute cycle, press and releasethe UNLOCK button on the RKE transmitter to unlockthe doors and disarm the Vehicle Security Alarm (ifequipped). Then, insert the key into the ignition switchand turn the switch to the ON position.

NOTE: The ignition switch must be in the ON positionin order to drive the vehicle.

To Turn Off the Engine While in Remote StartModePress and release the REMOTE START button one time.

NOTE: To avoid inadvertent shut downs, the systemwill disable the one-time press of the REMOTE STARTbutton for two seconds after receiving a valid RemoteStart request.


DOOR LOCKSManual Door LocksTo lock each door, push the door lock plunger on eachdoor trim panel downward. To unlock each door, pull thedoor lock plunger on each door trim panel upward.

If the door lock plunger is down when you shut the door,the door will lock. Therefore, make sure the keys are notinside the vehicle before closing the door.

NOTE: The manual door locks will not lock or unlockthe liftgate.

WARNING!

For personal security and safety in the event of anaccident, lock the vehicle doors as you drive aswell as when you park and leave the vehicle.

When leaving the vehicle always remove the keyfrom the ignition lock, and lock your vehicle.Unsupervised use of vehicle equipment may causesevere personal injuries and death.

(Continued)

Manual Lock Plunger


2

WARNING! (Continued) Never leave children alone in a vehicle. Leaving

unattended children in a vehicle is dangerous for anumber of reasons. A child or others could beseriously or fatally injured. Dont leave the key inthe ignition. A child could operate power win-dows, other controls, or move the vehicle.

Power Door LocksA power door lock switch is located on each of the frontdoor trim panels. Use this switch to lock or unlock thedoors and liftgate.

If you press the power door LOCK switch while the keyis in the ignition, and any front door is open, the powerlocks will not operate. This prevents you from acciden-tally locking your keys in the vehicle. Removing the keyor closing the door will allow the locks to operate. Achime will sound if the key is in the ignition switch anda door is open, as a reminder to remove the key.

Power Door Lock Switch


Automatic Door LocksThe doors will lock automatically on vehicles with powerdoor locks if all of the following conditions are met:

1. The Automatic Door Locks feature is enabled.

2. The transmission is in gear.

3. All doors are closed.

4. The throttle is pressed.

5. The vehicle speed is above 15 mph (24 km/h).

6. The doors were not previously locked using the powerdoor lock switch or Remote Keyless Entry (RKE)transmitter.

Automatic Door Locks ProgrammingThe Automatic Door Locks feature can be enabled ordisabled as follows:

For vehicles equipped with the Electronic VehicleInformation Center (EVIC), refer to Personal Settings(Customer Programmable Features) under Elec-tronic Vehicle Information Center (EVIC) in Section 4.

For vehicles not equipped with the EVIC, performingthe following procedure:

1. Close all doors and place the key in the ignition.

2. Cycle the ignition switch between LOCK and ON andthen back to LOCK four times, ending up in the LOCKposition.

3. Depress the power door LOCK switch to lock thedoors.

4. A single chime will indicate the completion of theprogramming.


2


NOTE: Use the Automatic Door Locks feature in accor-dance with local laws.

Automatic Unlock Doors on ExitThe doors will unlock automatically on vehicles withpower door locks if:

1. The Automatic Unlock Doors On Exit feature is en-abled.

2. The transmission is in gear and the vehicle speedreturned to 0 mph (0 km/h).

3. The transmission is in NEUTRAL or PARK.

4. The driver door is opened.

5. The doors were not previously unlocked.

6. The vehicle speed is 0 mph (0 km/h).

Automatic Unlock Doors on Exit ProgrammingThe Automatic Unlock Doors On Exit feature can beenabled or disabled as follows:

For vehicles equipped with the Electronic VehicleInformation Center (EVIC), refer to Personal Settings(Customer Programmable Features) under Elec-tronic Vehicle Information Center (EVIC) in Section 4.

For vehicles not equipped with the EVIC, perform thefollowing procedure:

1. Close all doors and place the key in the ignition.

2. Cycle the ignition switch between LOCK and ON andthen back to LOCK four times, ending up in the LOCKposition.

3. Depress the power door UNLOCK switch to unlockthe doors.


4. A single chime will indicate the completion of theprogramming.

Repeat these steps if you want to return this feature to itsprevious setting.

NOTE: Use the Automatic Unlock Doors On Exit featurein accordance with local laws.

Child-Protection Door Lock System (Rear Doors)To provide a safer environment for small children ridingin the rear seats, the rear doors are equipped with a ChildProtection Door Lock system.

To Engage the Child Protection Door Lock

1. Open the rear door.

2. Insert the tip of the ignition key into the child lockcontrol and rotate it to the LOCK position.

3. Repeat Steps 1 and 2 on the opposite rear door.

NOTE: When the child lock system is engaged, the doorcan be opened only by using the outside door handleeven though the inside door lock is in the unlockedposition.

Inserting Ignition Key


2

WARNING!

Avoid trapping anyone in a vehicle in a collision.Remember that the rear doors can only be openedfrom the outside when the child protection locks areengaged.

NOTE: After engaging the Child Protection Door Lock sys-

tem, always test the door from the inside to makecertain it is in the desired position.

For emergency exit with the system engaged, movethe lock plunger up (unlocked position), roll down thewindow, and open the door with the outside doorhandle.

To Disengage the Child Protection Door Lock

1. Open the rear door.

2. Insert the tip of the ignition key into the child lockcontrol and rotate it to the UNLOCK position.

3. Repeat Steps 1 and 2 on the opposite rear door.

NOTE: After disengaging the Child Protection DoorLock system, always test the door from the inside tomake certain it is in the desired position.

Inserting Ignition Key


WINDOWSPower WindowsThe window controls on the drivers door trim panelcontrol all the door windows.

There are single window controls on each passenger doortrim panel, which operate the passenger door windows.The window controls will operate when the ignitionswitch is in the ON or ACC position.

WARNING!

Never leave children in a vehicle, with the key in theignition switch. Occupants, particularly unattendedchildren, can become entrapped by the windowswhile operating the power window switches. Suchentrapment may result in serious injury or death.

Power Window Switches


2

Auto Down FeatureThe driver power window switch has an Auto Downfeature. Press the window switch past the first detent,release, and the window will go down automatically.

To open the window part way, press the window switchto the first detent and release it when you want thewindow to stop.

To stop the window from going all the way down duringthe Auto Down operation, pull up on the switch briefly.

For vehicles not equipped with the Electronic VehicleInformation Center (EVIC), the power window switcheswill remain active for 45 seconds after the ignition switchis turned to the LOCK position. Opening either frontdoor will cancel this feature.

For vehicles equipped with the EVIC, the power windowswitches will remain active for up to 10 minutes after theignition switch is turned to the LOCK position. Opening

either front door will cancel this feature. The time isprogrammable. For details, refer to Delay Power Off toAccessories Until Exit, under Personal Settings (Cus-tomer Programmable Features, under Electronic Ve-hicle Information Center (EVIC) in Section 4.

Auto Up Feature with Anti-Pinch Protection IfEquippedOn some models, the drivers power window switch hasan Auto Up feature. Pull the window switch up to thesecond detent, release, and the window will go upautomatically.

To stop the window from going all the way up during theAuto Up operation, push down on the switch briefly.

To close the window part way, pull the window switchup to the first detent and release when you want thewindow to stop.


For vehicles not equipped with the Electronic VehicleInformation Center (EVIC), the power window switcheswill remain active for 45 seconds after the ignition switchis turned to the LOCK position. Opening either frontdoor will cancel this feature.

For vehicles equipped with the EVIC, the power windowswitches will remain active for up to 10 minutes after theignition switch is turned to the LOCK position. Openingeither front door will cancel this feature. The time isprogrammable. For details, refer to Delay Power Off toAccessories Until Exit, under Personal Settings (Cus-tomer Programmable Features) under Electronic Ve-hicle Information Center (EVIC) in Section 4.

NOTE: If the window runs into any obstacle during auto-

closure, it will reverse direction and then stop. Removethe obstacle and use the window switch again to closethe window.

Any impact due to rough road conditions may triggerthe auto reverse function unexpectedly during auto-closure. If this happens, pull the switch lightly to thefirst detent and hold to close window manually.

WARNING!

There is no anti-pinch protection when the windowis almost closed. Be sure to clear all objects from thewindow before closing.


2

Window Lockout SwitchThe window lockout switch on the drivers door trimpanel allows you to disable the window control on theother doors. To disable the window control on the otherdoors, press and release the window LOCK button(setting it in the down position). To enable the windowcontrols, press and release the window LOCK buttonagain (setting it in the up position).

Window Lockout Switch


ResetIt may be necessary at some point in time to reactivate theAuto Up feature. To do so, perform the following proce-dure:

1. Pull the window switch up to close window com-pletely and continue to hold the switch up for anadditional two seconds after the window is closed.

2. Push the window switch down firmly to the seconddetent to open the window completely and continue tohold the switch down for an additional two seconds afterthe window is fully open.

Wind BuffetingWind buffeting can be described as the perception ofpressure on the ears or a helicopter-type sound in theears. Your vehicle may exhibit wind buffeting with thewindows down, or the sunroof or Sky Slidert (ifequipped) in certain open or partially open positions.This is a normal occurrence and can be minimized. If thebuffeting occurs with the rear windows open, then openthe front and rear windows together to minimize thebuffeting. If the buffeting occurs with the sunroof or SkySlidert open, adjust the sunroof or Sky Slidert openingto minimize the buffeting or open any window.


2

LIFTGATETo open the liftgate, pull up (squeeze) on the handle andlift.

NOTE: Use the power door LOCK switch on either frontdoor trim panel or the Remote Keyless Entry (RKE)transmitter to lock and unlock the liftgate. The manual

door locks on the doors and the drivers door lockcylinder will not lock and unlock the liftgate.

WARNING!

Driving with the liftgate open can allow poisonousexhaust gases into your vehicle. You and your pas-sengers could be injured by these fumes. Keep theliftgate closed when you are operating the vehicle.

OCCUPANT RESTRAINTSSome of the most important safety features in yourvehicle are the restraint systems. These include the frontand rear seat belts for the driver and all passengers, frontairbags for both the driver and front passenger, and sidecurtain airbags for the driver and passengers seated nextto a window. If you will be carrying children too small foradult-size belts, your seat belts also can be used to holdinfant and child restraint systems.

Liftgate Release


Please pay close attention to the information in thissection. It tells you how to use your restraint systemproperly to keep you and your passengers as safe aspossible.

WARNING!

In a collision, you and your passengers can sufferinjuries, including fatalities, if you are not properlybuckled up. You can strike the interior of yourvehicle or other passengers, or you can be thrown outof the vehicle. Always be sure you and others in yourvehicle are buckled up properly.

Buckle up even though you are an excellent driver, evenon short trips. Someone on the road may be a poor driverand cause a collision that includes you. This can happenfar away from home or on your own street.

Research has shown that seat belts save lives, and theycan reduce the seriousness of injuries in a collision. Someof the worst injuries happen when people are thrownfrom the vehicle. Seat belts reduce the possibility ofejection and the risk of injury caused by striking theinside of the vehicle. Everyone in a motor vehicle shouldbe belted at all times to reduce or prevent injuries.

Lap/Shoulder BeltsAll seating positions in your vehicle have combinationlap/shoulder belts. The belt webbing retractor is de-signed to lock during very sudden stops or collisions.This feature allows the shoulder part of the belt to movefreely with you under normal conditions. However, in acollision, the belt will lock and reduce your risk ofstriking the inside of the vehicle or being thrown out.


2

WARNING!

It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, peopleriding in these areas are more likely to be seri-ously injured or killed.

Do not allow people to ride in any area of yourvehicle that is not equipped with seats and seatbelts.

Be sure everyone in your vehicle is in a seat andusing a seat belt properly.

Wearing a seat belt incorrectly is dangerous. Seatbelts are designed to go around the large bones ofyour body. These are the strongest parts of yourbody and can take the forces of a collision the best.

(Continued)

WARNING! (Continued) Wearing your belt in the wrong place could make

your injuries in a collision much worse. You mightsuffer internal injuries, or you could even slide outof part of the belt. Follow these instructions towear your seat belt safely and to keep your pas-sengers safe, too.

Two people should never be belted into a singleseat belt. People belted together can crash into oneanother in an accident, hurting one another badly.Never use a lap/shoulder belt or a lap belt for morethan one person, no matter what their size.

Lap/Shoulder Belt Operating Instructions

1. Enter the vehicle and close the door. Sit back andadjust the seat.


2. The seat belt latch plate, located on the B-Pillar is justabove your seatback. Grasp the latch plate and pull outthe belt. Slide the latch plate up the webbing as far asnecessary to make the belt go around your lap.

3. When the belt is long enough to fit, insert the latchplate into the buckle until you hear a click.

Latch Plate

Latch Plate To Buckle


2

WARNING!

A belt that is buckled into the wrong buckle willnot protect you properly. The lap portion could ridetoo high on your body, possibly causing internalinjuries. Always buckle your belt into the bucklenearest you. A belt that is too loose will not protect you as well.In a sudden stop, you could move too far forward,increasing the possibility of injury. Wear your seatbelt snugly. A belt that is worn under your arm is very danger-ous. Your body could strike the inside surfaces of thevehicle in a collision, increasing head and neckinjury. A belt worn under the arm can cause internalinjuries. Ribs arent as strong as shoulder bones.Wear the belt over your shoulder so that your stron-gest bones will take the force in a collision.

(Continued)

WARNING! (Continued) A shoulder belt placed behind you will not protectyou from injury during a collision. You are morelikely to hit your head in a collision if you do notwear your shoulder belt. The lap and shoulder beltare meant to be used together.

4. Position the lap belt across your thighs, below yourabdomen. To remove slack in the lap belt portion, pull upa bit on the shoulder belt. To loosen the lap belt if it is tootight, tilt the latch plate and pull on the lap belt. A snugbelt reduces the risk of sliding under the belt in acollision.


WARNING!

A lap belt worn too high can increase the risk ofinjury in a collision. The belt forces wont be at thestrong hip and pelvic bones, but across your abdo-men. Always wear the lap part of your seat belt aslow as possible and keep it snug. A twisted belt cant do its job as well. In a collision,it could even cut into you. Be sure the belt is straight.If you cant straighten a belt in your vehicle, take it toyour authorized dealer and have it fixed.

5. Position the shoulder belt on your chest so that it iscomfortable and not resting on your neck. The retractorwill withdraw any slack in the belt.

6. To release the belt, push the red button on the buckle.The belt will automatically retract to its stowed position.If necessary, slide the latch plate down the webbing toallow the belt to retract fully.

Removing Slack From Belt


2

WARNING!

A frayed or torn belt could rip apart in a collision andleave you with no protection. Inspect the belt systemperiodically, checking for cuts, frays, or loose parts.Damaged parts must be replaced immediately. Do notdisassemble or modify the system. Seat belt assem-blies must be replaced after an accident if they havebeen damaged (bent retractor, torn webbing, etc.).

Adjustable Upper Shoulder Belt AnchorageIn the front seating positions, the shoulder belt can beadjusted upward or downward to position the belt awayfrom your neck. Press the RELEASE button to release theanchorage, and then move it up or down to the positionthat fits you best.

NOTE: The adjustable upper shoulder belt anchorage isequipped with an Easy Up feature. This feature allows theshoulder belt anchorage to be adjusted in the upward

position without pressing the release button. To verify theshoulder belt anchorage is latched, pull downward on theshoulder belt anchorage until it is locked into position.

As a guide, if you are shorter than average you willprefer a lower position, and if you are taller than averageyou will prefer a higher position.

Adjusting Upper Shoulder Belt


Lap/Shoulder Belt Untwisting ProcedureUse the following procedure to untwist a twisted lap/shoulder belt.

1. Position the latch plate as close as possible to theanchor point.

2. At about 6 to 12 in (15 to 30 cm) above the latch plate,grasp and twist the belt webbing 180 degrees to create afold that begins immediately above the latch plate.

3. Slide the latch plate upward over the folded webbing.The folded webbing must enter the slot at the top of thelatch plate.

4. Continue to slide the latch plate up until it clears thefolded webbing.

Seat Belt Pretensioner If PresentThe front passenger seat belt is equipped with a preten-sioning device that is designed to remove any slack fromthe seat belt systems in the event of a collision. Thesedevices improve the performance of the seat belt byassuring that the belt is tight around the occupant earlyin a collision. Pretensioners work for all size occupants,including those in child restraints.

NOTE: These devices are not a substitute for proper seatbelt placement by the occupant. The seat belt must still beworn snugly and positioned properly.

The pretensioner is triggered by the Occupant RestraintController (ORC). Like the front airbags, the pretension-ers are single use items. After a collision that is severeenough to deploy the airbags and pretensioners, bothmust be replaced.


2

Enhanced Seat Belt Use Reminder System(BeltAlertT)If the drivers or front passengers seat belt has not beenbuckled within 60 seconds of starting the vehicle, and ifthe vehicle speed is greater than 5 mph (8 km/h), theEnhanced Warning System (BeltAlertt) will alert thedriver or front passenger to buckle their seat belt. Thedriver should also instruct all other occupants to buckletheir seat belts. Once the warning is triggered, theEnhanced Warning System (BeltAlertt) will continue tochime and flash the Seat Belt Reminder Light for 96 sec-onds or until the drivers or front passengers seat belt isbuckled. The Enhanced Warning System (BeltAlertt) willbe reactivated if the drivers or front passengers seat beltis unbuckled for more than 10 seconds and the vehiclespeed is greater than 5 mph (8 km/h).

BeltAlertt ProgrammingThe Enhanced Warning System (BeltAlertt) can be en-abled or disabled by your authorized dealer or byperforming the following steps:

NOTE: Chrysler LLC does not recommend deactivatingthe Enhanced Warning System (BeltAlertt).

1. With all doors closed, and the ignition switch in anyposition except ON or START, buckle the drivers seatbelt.

2. Turn the ignition switch to the ON position, but do notstart the engine. Wait for the Seat Belt Reminder Light toturn off and then proceed to the next step.

NOTE: You must perform the following steps within60 seconds of turning the ignition switch to the ONposition.


3. Within 60 seconds of turning the ignition switch to theON position, unbuckle and then re-buckle the driversseat belt at least three times within 10 seconds, endingwith the seat belt buckled.

NOTE: Watch for the Seat Belt Reminder Light to turnon while unbuckling the seat belt and turn off whilere-buckling the seat belt. It may be necessary to retractthe seat belt.

4. Turn the ignition switch to the LOCK position. Asingle chime will sound to signify that you have success-fully completed the programming.

The Enhanced Warning System (BeltAlertt) can be reac-tivated by repeating this procedure.

NOTE: When the Enhanced Warning System(BeltAlertt) is deactivated, the Seat Belt Reminder Lightwill continue to illuminate as long as the drivers seat beltis unbuckled.

Automatic Locking Mode If EquippedIn this mode, the shoulder belt is automatically pre-locked. However, the belt will still retract to remove anyslack in the shoulder belt.

When To Use The Automatic Locking ModeUse the Automatic Locking mode anytime a child safetyseat is installed in the rear outboard seating position.Children 12 years old and younger should be properlyrestrained in the rear seat whenever possible.

How To Use The Automatic Locking Mode

1. Buckle the combination lap and shoulder belt.

2. Grasp the shoulder portion and pull downward untilthe entire belt is extracted.

3. Allow the belt to retract. As the belt retracts, you willhear a clicking sound. This indicates the safety belt isnow in the Automatic Locking mode.


2

How to Disengage The Automatic Locking ModeDisconnect the combination lap/shoulder belt from thebuckle and allow it to retract completely to disengage theAutomatic Locking mode and activate the vehicle sensi-tive (emergency) locking mode.

Energy Management FeatureThis vehicle has a safety belt system with an energymanagement feature in the front seating positions to helpfurther reduce the risk of injury in the event of a head-oncollision.

This safety belt system has a retractor assembly that isdesigned to release webbing in a controlled manner. Thisfeature is designed to help reduce the belt force acting onthe occupants chest.

WARNING!

The belt and retractor assembly must be replacedif the seat belt assembly automatic locking retrac-tor feature or any other seat belt function is notworking properly when checked according to theprocedures in the Service Manual.

Failure to replace the belt and retractor assemblycould increase the risk of injury in collisions.


Seat Belts and Pregnant WomenWe recommend that pregnant women use the seat beltsthroughout their pregnancy. Keeping the mother safe isthe best way to keep the baby safe.

Pregnant women should wear the lap part of the beltacross the thighs and as snug across the hips as possible.Keep the belt low so that it does not come across theabdomen. That way the strong bones of the hips will takethe force if there is a collision.

Seat Belt ExtenderIf a seat belt is too short, even when fully extended, andwhen the adjustable upper shoulder belt anchorage (if soequipped) is in its lowest position, your authorizeddealer can provide you with a seat belt extender. Thisextender should be used only if the existing belt is notlong enough. When it is not required, remove the ex-tender, and store it.

WARNING!

Using a seat belt extender when not needed canincrease the risk of injury in a collision. Only usewhen the lap belt is not long enough when it is wornlow and snug, and in the recommended seatingpositions. Remove and store the extender when notneeded.


2

Driver and Front Passenger SupplementalRestraint System (SRS) - AirbagThis vehicle has airbags for both the driver and frontpassenger as a supplement to the seat belt restraintsystems. The drivers airbag is mounted in the steeringwheel. The passengers front airbag is mounted in theinstrument panel, above the glove compartment. Thewords SRS AIRBAG are embossed on the airbag covers.

NOTE: The front airbags are certified to the Federalregulations that allow less forceful deployment.

1 Driver Airbag2 Passenger Airbag


The front airbags have a multistage inflator design. Thismay allow the airbag to have different rates of inflationthat are based on collision severity and occupant size.The front passenger airbag is also certified to the Federalregulations that define Occupant Classification (refer toinformation on Occupant Classification System in thissection).

This vehicle is equipped with side curtain airbags toprotect the driver and the front and rear passengerssitting next to a window. They are located above the sidewindows. Their covers are also labeled SRS AIRBAG.

NOTE: Airbag covers may not be obvious in the interiortrim; but they will open to allow airbag deployment.

Window Airbag Location


2

WARNING!

Do not put anything on or around the front andside curtain airbag covers or attempt to manuallyopen them. You may damage the airbags and youcould be injured because the airbags are no longerfunctional. These protective covers for the airbagcushions are designed to open only when theairbags are inflating.

Do not stack luggage or other cargo up highenough to block the location of the side curtainairbag. The area where the side curtain airbag islocated should remain free from any obstructions.

Do not have any accessory items installed whichwill alter the roof, including adding a sunroof toyour vehicle. Do not add roof racks that requirepermanent attachments (bolts or screws) for instal-lation on the vehicle roof. Do not drill into the roofof the vehicle for any reason.

(Continued)

WARNING! (Continued) Do not cover or place items on the airbag covers.

These items may cause serious injury duringinflation.

Along with the seat belts, the front airbags provideimproved protection for the driver and front passenger.Side Curtain Airbags also work with seat belts to im-prove occupant protection.

The seat belts are designed to protect you in many typesof collisions. The front airbags deploy in moderate tosevere collisions. The Side Curtain Airbag will alsotrigger on the crash side of the vehicle in moderate tosevere side collisions or on both sides of the vehicle inrollover collisions. In certain types of collisions, both thefront and side airbags may be triggered. However, evenin collisions where the airbags deploy, you need the seatbelts to keep you in the right position for the airbags toprotect you properly.


NOTE: The passenger front airbag may not deploy evenwhen the driver front airbag has; particularly if theOccupant Classification System has determined the pas-senger seat is empty or is occupied by someone that isclassified in a category other than that of an adult (referto information on Occupant Classification System in thissection). This could be a child, teenager, or even a smallsize adult.

Here are some simple steps you can take to minimizethe risk of harm from a deploying airbag.

1. Children 12 years old and younger should always ridebuckled up in the rear seat.

Infants in rear facing child restraints should NEVER ridein the front seat of a vehicle with a passenger front airbag.An airbag deployment could cause severe injury or deathto infants in that position.

Children that are not big enough to wear the vehicle seatbelt properly should be secured in the rear seat in childrestraints or belt-positioning booster seats. Older chil-dren who do not use child restraints or belt-positioningbooster seats should ride properly buckled up in the rearseat. Never allow children to slide the shoulder beltbehind them or under their arms.

If a child from 1 to 12 years old must ride in the frontpassenger seat because the vehicle is crowded, move theseat as far back as possible, and use the proper childrestraint (refer to information on Child Restraint in thissection).

You should read the instructions provided with yourchild restraint to make sure that you are using it properly.

2. All occupants should use their lap and shoulder beltsproperly.


2

3. The driver and front passenger seats should be movedback as far as practical to allow the front airbags room toinflate.

4. Do not lean against the door or window, airbags willinflate forcefully into the space between you and thedoor.

5. If the airbag system in this vehicle needs to bemodified to accommodate a disabled person, contact theCustomer Center. Phone numbers are provided under IfYou Need Assistance in Section 9 of this manual.

WARNING!

Relying on the airbags alone could lead to moresevere injuries in a collision. The airbags workwith your seat belt to restrain you properly. Insome collisions, the airbags wont deploy at all.Always wear your seat belts even though you haveairbags.

Being too close to the steering wheel or instrumentpanel during airbag deployment could cause seri-ous injury. Airbags need room to inflate. Sit back,comfortably extending your arms to reach thesteering wheel or instrument panel.

The side curtain airbags need room to inflate. Donot lean against the door or window. Sit upright inthe center of the seat.


Airbag System ComponentsThe airbag system consists of the following:

Occupant Restraint Controller (ORC) Airbag Warning Light Driver Airbag Front Passenger Airbag Side Curtain Airbags above Side Windows Side Remote Acceleration Sensors Steering Wheel and Column Instrument Panel Interconnecting Wiring Front Acceleration Sensors Front Passenger Seat Belt Pretensioner and Retractor

If Present

Occupant Classification System (OCS) Front Pas-senger Seat Only

Occupant Classification Module (OCM)

Passenger Airbag Disable (PAD) Indicator Light

Weight Sensors

How The Airbag System Works

The Occupant Restraint Controller (ORC) determinesif a frontal, side, or rollover collision is severe enoughto require the airbags to inflate. The front airbaginflators are designed to provide different rates ofairbag inflation from direction provided by the ORC.The ORC may also modify the rate of inflation basedon the occupant size. The ORC receives this data fromthe Occupant Classification Module (OCM). The ORCwill detect rollovers, but not rear impacts.

The ORC also monitors the readiness of the electronicparts of the system whenever the ignition switch is in


2

the START or ON position. These include all of theitems listed above except the Passenger Airbag Disable(PAD) Indicator Light, the instrument panel, and thesteering wheel and column. If the key is in the LOCKposition, in the ACC position, or not in the ignition,the airbags are not on and they will not inflate.

The ORC also turns on the Airbag WarningLight and PAD Indicator Light for six toeight seconds as a self-check when the igni-tion is first turned ON. After the self-check,

the Airbag Warning Light will turn off. The PADIndicator Light will function normally (refer to infor-mation on Passenger Airbag Disable (PAD) IndicatorLight in this section). If the ORC detects a malfunctionin any part of the system, it turns on the AirbagWarning Light either momentarily or continuously. Asingle chime will sound if the light comes on againafter initial start up.

WARNING!

Ignoring the Airbag Warning Light in your instru-ment panel could mean you wont have the airbags toprotect you in a collision. If the light does not comeon, stays on after you start the vehicle, or if it comeson as you drive, have the airbag system checked rightaway.

The Occupant Classification System (OCS) is part ofa Federally regulated safety system required for thisvehicle. It is designed to turn off the front passengerairbag for an empty seat and for occupants classifiedin a category other than that of an adult. This could bea child, teenager, or even a small size adult.

NOTE: Children 12 years and younger should alwaysride buckled up in a rear seat in an appropriate childrestraint.


The Passenger Airbag Disable (PAD) Indicator Light(an amber light located in the center of the instrumentpanel) tells the driver and front passenger when thefront passenger airbag is turned off. The PAD Indi-cator Light illuminates the words 9PASS AIR BAGOFF9 to show that the passenger airbag will not inflateduring a collision requiring airbags. When the frontpassenger seat is empty or when very light objects areplaced on the seat, the passenger airbag will not inflateeven though the PAD Indicator Light is not illumi-nated.

The PAD Indicator Light should not be illuminatedwhen an adult passenger is properly seated in thefront passenger seat. In this case, the airbag is ready tobe inflated if a collision requiring an airbag occurs. Forall other occupants, the PAD Indicator Light will beilluminated indicating that the front passenger airbag

Indicator Light Location


2

is turned off and it will not inflate. If the PADIndicator Light is not illuminated, DO NOT assumethe airbag is turned off and move the child restraint tothe rear seat. A deploying passenger airbag can causedeath or serious injury to a child in a rear facing infantseat.

NOTE: Even though this vehicle is equipped with anOccupant Classification System, children 12 years andyounger should always ride buckled up in a rear seat inan appropriate child restraint.

Front PassengerSeat Occupant

PassengerAirbag Disable(PAD) Indicator

Light

Airbag Status

Adult OFF ONGrocery Bags,Heavy Brief-

cases, and OtherRelatively Light

Objects

ON OFF

Empty or VerySmall Objects OFF* OFF

* Since the system senses weight, some small objectswill turn the PAD Indicator Light on.


The OCS classifies an occupant using weight sensorsmounted in the base of the front passenger seat. Anyweight on the seat will be sensed by the system. Objectshanging on the seat or other passengers pushing downon the seat will also be sensed. The weight of an adultwill cause the system to turn the airbag on. In this case,the OCS has classified the occupant of the seat as anadult. An adult occupant needs to sit in a normal position(with their feet on or near the floor) in order to beproperly classified. Reclining the seat back too far maychange how an occupant is classified by the OCS.

Drivers and adult passengers should verify that thePAD Indicator Light is not illuminated when an adultis riding in the front passenger seat. If an adult occu-pants weight is transferred to another part of the vehicle(like the door or instrument panel), the weight sensors inthe seat may not properly classify the occupant. Objectslodged under the seat or between the seat and the centerconsole can prevent the occupants weight from being

measured properly and may result in the occupant beingimproperly classified. Ensure that the front passengerseatback does not touch anything placed on the back seatbecause this can also affect occupant classification. Also,if you fold down the rear seat check to be sure it doesnttouch the front passenger seat.

If the front passenger seat is damaged in any way, itshould only be serviced by an authorized dealer. If theseat is removed (or even if the seat attachment bolts areloosened or tightened in any way), take the vehicle to anauthorized dealer.

If there is a fault present in the OCS, the Airbag WarningLight (a red light located in the center of the instrumentcluster directly in front of the driver) will be turned on.This indicates that you should take the vehicle to anauthorized dealer. The Airbag Warning Light is turnedon whenever there is a fault that can affect the operationof the airbag system. If there is a fault present in the OCS,


2

both the PAD Indicator Light and the Airbag WarningLight are illuminated to show that the passenger airbagis turned off until the fault is cleared. If an object islodged under the seat and interferes with operation ofthe weight sensors, a fault will occur which turns on boththe PAD Indicator Light and the Airbag WarningLight. Once the lodged object is removed, the fault willbe automatically cleared after a short period of time.

The Driver and Passenger Airbag/Inflator Units arelocated in the center of the steering wheel and thepassenger side of the instrument panel. When the ORCdetects a collision requiring the airbags, it signals theinflator units. A large quantity of nontoxic gas isgenerated to inflate the front airbags. Different airbaginflation rates are possible, based on collision severityand occupant size. The steering wheel hub trim coverand the upper passenger side of the instrument panelseparate and fold out of the way, as the bags inflate totheir full size. The bags fully inflate in about 50 to 70

milliseconds. This is about half of the time that it takesto blink your eyes. The bags then quickly deflate whilehelping to restrain the driver and front passenger. Thedrivers front airbag gas is vented through the ventholes in the sides of the airbag. The passengers frontairbag gas is vented through the vent holes in the sidesof the airbag. In this way, the airbags do not interferewith your control of the vehicle.

The Occupant Classification Module (OCM) is lo-cated beneath the front passenger seat. The OCMclassifies the occupant into categories based on themeasurements made by the seat weight sensors. TheOCM communicates with the Occupant Restraint Con-troller (ORC). The ORC uses the occupant category todetermine whether the front passenger airbag shouldbe turned off. It also determines the rate of airbaginflation during a collision.


Your vehicle has four Weight Sensors located betweenthe seat and the floor pan. The weight sensors measureapplied weight and transfers that information to theOCM.

The Side Impact SRS Side Curtain Airbags are de-signed to activate only in certain side collisions androllover events. When the ORC detects a collisionrequiring the side curtain airbag to inflate, it signalsthe inflators on the crash side of the vehicle or bothsides of the vehicle for a rollover event. A quantity ofnontoxic gas is generated to inflate the side curtainairbag. The inflating side curtain airbag pushes theoutside edge of the headliner out of the way andcovers the window. The airbag inflates in about 30milliseconds (about one-quarter of the time that it

takes to blink your eyes) with enough force to injureyou if you are not belted and seated properly, or ifitems are positioned in the area where the side curtainairbag inflates. This especially applies to children. Theside curtain airbag is only about 3 12 in (9 cm) thickwhen it is inflated.

The front passenger seat assembly contains critical com-ponents that affect the front passenger airbag deploy-ment. Correctly functioning front passenger seat compo-nents are critical for the Occupant Classification System(OCS) to properly classify the front passenger and calcu-late the proper airbag deployment. Do not make anymodifications to the front passenger seat components orassembly.


2

The following requirements must be strictly adhered to:

Do not modify the front passenger seat assembly orcomponents in any way.

At no time should any Supplemental Restraint System(SRS) component or SRS related component or fas-tener be modified or replaced with any part exceptthose which are approved by Chrysler LLC/Mopart.

WARNING!

Unapproved modifications or service procedures tothe front passenger seat assembly or its related com-ponents may inadvertently change the airbag deploy-ment in case of a frontal crash. This could result indeath or serious injury to the front seat passenger ifthe vehicle is involved in an accident. A modifiedvehicle may not comply with required Federal MotorVehicle Safety Standards (FMVSS).

If A Deployment OccursThe airbag system is designed to deploy when theOccupant Restraint Controller (ORC) detects a moderate-to-severe collision, to help restrain the driver and frontpassenger, and then to immediately deflate.

NOTE: A collision that is not severe enough to needairbag protection will not activate the system. This doesnot mean something is wrong with the airbag system.

If you do have a collision which deploys the airbags, anyor all of the following may occur:

The nylon airbag material may sometimes cause abra-sions and/or skin reddening to the driver and frontpassenger as the airbags deploy and unfold. Theabrasions are similar to friction rope burns or thoseyou might get sliding along a carpet or gymnasiumfloor. They are not caused by contact with chemicals.They are not permanent and normally heal quickly.


However, if you havent healed significantly within afew days, or if you have any blistering, see your doctorimmediately.

As the airbags deflate, you may see some smoke-likeparticles. The particles are a normal by-product of theprocess that generates the nontoxic gas used for airbaginflation. These airborne particles may irritate the skin,eyes, nose, or throat. If you have skin or eye irritation,rinse the area with cool water. For nose or throatirritation, move to fresh air. If the irritation continues,see your doctor. If these particles settle on yourclothing, follow the garment manufacturers instruc-tions for cleaning.

It is not advisable to drive your vehicle after theairbags have deployed. If you are involved in anothercollision, the airbags will not be in place to protect you.

WARNING!

Deployed airbags and seat belt pretensioners cannotprotect you in another collision. Have the airbags,seat belt pretensioner, and seat belt retractor assem-bly replaced by an authorized dealer as soon aspossible. Also, have the Occupant Classification Sys-tem serviced as well.


2

Enhanced Accident Response SystemIn the event of an impact that causes airbag deployment,with the vehicle stopped, and the vehicle communicationnetwork intact, and the power intact, the EnhancedAccident Response System performs the following func-tions:

Cuts off fuel to the engine. Flashes hazard lights. Turns on the interior lights, which remain on as long as

the battery has power or until the ignition key isremoved.

Unlocks the doors automatically.NOTE: The interior lights can only be deactivated if thekey is removed from the ignition switch or the vehicle isdriven.

Maintaining Your Airbag System

WARNING!

Modifications to any part of the airbag systemcould cause it to fail when you need it. You couldbe injured if the airbag system is not there toprotect you. Do not modify the components orwiring, including adding any kind of badges orstickers to the steering wheel hub trim cover or theupper passenger side of the instrument panel. Donot modify the front bumper or vehicle bodystructure.

(Continued)


WARNING! (Continued) Do not attempt to modify any part of your ad-

vanced airbag system. The airbag may inflateaccidentally or may not function properly if modi-fications are made. Take your vehicle to an autho-rized dealer for any advanced airbag system ser-vice. If your seat including your trim cover andcushion needs to be serviced in any way (includ-ing removal or loosening/tightening of seat attach-ment bolts), take the vehicle to your authorizeddealer. Only manufacturer approved seat accesso-ries may be used. If it is necessary to modify anadvanced airbag system for persons with disabili-ties, contact your authorized dealer.

(Continued)

WARNING! (Continued) Do not place or hang any items such as add-on

video players on the front passenger seatback. Theadditional weight may cause the Occupant Classi-fication System to be unable to classify the frontseat passenger correctly. This could allow thepassenger frontal airbag to inflate when it is notdesired.

It is dangerous to try to repair any part of theairbag system yourself. Be sure to tell anyone whoworks on your vehicle that it has an airbag system.


2

Airbag Warning LightYou will want to have the airbag system ready to inflatefor your protection in an impact. The airbag system isdesigned to be maintenance free. If any of the followingoccurs, have an authorized dealer service the systempromptly:

The Airbag Warning Light does not come on or flickersduring the six to eight seconds when the ignitionswitch is first turned ON.

The light remains on or flickers after the six to eightsecond interval.

The light flickers or comes on and remains on whiledriving.

Event Data Recorder (EDR)In the event of an accident, your vehicle is designed torecord up to five seconds of specific vehicle data param-eters (see the following list) in an event data recorder

prior to the moment of airbag deployment, or neardeployment, and up to a quarter second of high-speeddeceleration data during and/or after airbag deploy-ment. EDR data are ONLY recorded if an airbag deploys,or nearly deploys, and are otherwise unavailable.

NOTE:1. A near-deployment event occurs when the airbagsensor detects severe vehicle deceleration usually indica-tive of a crash, but not severe enough to warrant airbagdeployment.

2. Under certain circumstances, EDR data may not berecorded (e.g., loss of battery power).

In conjunction with other data gathered during a com-plete accident investigation, the electronic data may beused by Chrysler LLC and others to learn more about thepossible causes of crashes and associated injuries in orderto assess and improve vehicle performance. In additionto crash investigations initiated by Chrysler LLC, such


investigations may be requested by customers, insurancecarriers, government officials, and professional crashresearchers, such as those associated with universities,and with hospital and insurance organizations.

In the event that an investigation is undertaken byChrysler LLC (regardless of initiative), the company or itsdesignated representative will first obtain permission ofthe appropriate custodial entity for the vehicle (usuallythe vehicle owner or lessee) before accessing the elec-tronic data stored, unless ordered to download data by acourt with legal jurisdiction (i.e., pursuant to a warrant).A copy of the data will be provided to the custodial entityupon request. General data that does not identify par-ticular vehicles or crashes may be released for incorpo-ration in aggregate crash databases, such as those main-tained by the US government and various states. Data ofa potentially sensitive nature, such as would identify a

particular driver, vehicle, or crash, will be treated confi-dentially. Confidential data will not be disclosed byChrysler LLC to any third party except when:

1. Used for research purposes, such as to match datawith a particular crash record in an aggregate database,provided confidentiality of personal data is thereafterpreserved.

2. Used in defense of litigation involving a Chrysler LLCproduct.

3. Requested by police under a legal warrant.

4. Otherwise required by law.


2

Data parameters that may be recorded:

Diagnostic trouble code(s) and warning light status forelectronically-controlled safety systems, including theairbag system

Airbag disable light status (if equipped) 9Time9 of airbag deployment (in terms of ignition

cycles and vehicle mileage)

Airbag deployment level (if applicable) Impact acceleration and angle Seat belt status Brake status (service and parking brakes) Accelerator status (including vehicle speed) Engine control status (including engine speed) Transmission gear selection

Cruise control status Traction/stability control status Tire Pressure Monitoring System statusChild RestraintEveryone in your vehicle needs to be buckled up all thetime babies and children, too. Every state in the UnitedStates and all Canadian provinces require that smallchildren ride in proper restraint systems. This is the law,and you can be prosecuted for ignoring it.

Children 12 years and younger should ride properlybuckled up in a rear seat, if available. According to crashstatistics, children are safer when properly restrained inthe rear seats rather than in the front.


WARNING!

In a collision, an unrestrained child, even a tiny baby,can become a missile inside the vehicle. The forcerequired to hold even an infant on your lap canbecome so great that you could not hold the child, nomatter how strong you are. The child and otherscould be badly injured. Any child riding in yourvehicle should be in a proper restraint for the childssize.

There are different sizes and types of restraints forchildren from newborn size to the child almost largeenough for an adult safety belt. Always check the childseat Owners Manual to ensure you have the right seatfor your child. Use the restraint that is correct for yourchild.

Infants and Child Restraints

Safety experts recommend that children riderearward-facing in the vehicle until they are at leastone year old and weigh at least 20 lbs (9 kg). Two typesof child restraints can be used rearward-facing: infantcarriers and convertible child seats.

The infant carrier is only used rearward-facing in thevehicle. It is recommended for children who weigh upto about 20 lbs (9 kg). Convertible child seats can beused either rearward-facing or forward-facing in thevehicle. Convertible child seats often have a higherweight limit in the rearward-facing direction thaninfant carriers do, so they can be used rearward-facingby children who weigh more than 20 lbs (9 kg) but areless than one year old. Both types of child restraints areheld in the vehicle by the lap/shoulder belt or theLATCH child restraint anchorage system. Refer toLATCH Child Seat Anchorage System (LowerAnchors and Tether for CHildren) in this section.


2

Rearward-facing child seats must NEVER be used inthe front seat of a vehicle with the front passengerairbag unless the airbag is turned off. An airbagdeployment could cause severe injury or death toinfants in this position.

Older Children and Child RestraintsChildren who weigh more than 20 lbs (9 kg) and who areolder than one year can ride forward-facing in thevehicle. Forward-facing child seats and convertible childseats used in the forward-facing direction are for childrenwho weigh 20 to 40 lbs (9 to 18 kg) and who are olderthan one year. These child seats are also held in thevehicle by the lap/shoulder belt or the LATCH childrestraint anchorage system. Refer to LATCH ChildSeat Anchorage System (Lower Anchors and Tether forCHildren) in this section.

The belt-positioning booster seat is for children weighingmore than 40 lbs (18 kg), but who are still too small to fitthe vehicles seat belts properly. If the child cannot sitwith knees bent over the vehicles seat cushion while thechilds back is against the seatback, they should use abelt-positioning booster seat. The child and belt-positioning booster seat are held in the vehicle by thelap/shoulder belt.

Children Too Large for Booster SeatsChildren who are large enough to wear the shoulder beltcomfortably, and whose legs are long enough to bendover the front of the seat when their back is against theseat back, should use the lap/shoulder belt in a rear seat.

Make sure that the child is upright in the seat. The lap portion of the seat belt should be low on the

hips and as snug as possible.


Check belt fit periodically. A childs squirming orslouching can move the belt out of position.

If the shoulder belt contacts the face or neck, move thechild closer to the center of the vehicle. Never allow achild to put the shoulder belt under an arm or behindtheir back.

NOTE: For additional information, refer towww.seatcheck.org or call 1866SEATCHECK.

WARNIN

Documents

2009 Liberty 1st, Manual, de uso