Upload
edidjo-darwin
View
55
Download
8
Tags:
Embed Size (px)
DESCRIPTION
audi ssp study
Citation preview
ATU Audi Technical UpdatesA3 2.0 TDI Turbo Charger Vacuum Unit
2 Title or name, division, Date
Contents: Technical actionsEngine
No. Event Topic Type/model
1 03/10 Replacing turbocharger a vacuum unit A3 and TT
Audi ATU, 8/2010
3 Title or name, division, Date
Replacing turbocharger vacuum units 2.0l CR TDI transversally installed Complaint and problem description
Glow plug filament flashes
The following entries may appear in the fault memory for the engine control unit:
- P0299 Charge pressure control, "lower than" control limit
- P2563 Position sender for charge pressure positioner, "implausible signal
Audi ATU, 8/2010
4 Title or name, division, Date
Necessary special tools
Create tools yourself - SW 14 to counterhold the connection for the oil supply line:
A = 110 mm
B = 25 mm
Testing and measuring equipment
- Hand vacuum pump "VAS 6213"
- Vehicle diagnostic tester
Replacing turbocharger vacuum units 2.0l CR TDI transversally installed
Caution:
The specified special tools, in particular the plug-in tool T10422, are designed solely for
use as described in the following work procedure and may not be used for other screw connections, as this runs the risk of
deformation caused by using higher torques.
Audi ATU, 8/2010
5 Title or name, division, Date
Replacing turbocharger vacuum units 2.0l CR TDI transversally installed Note:
A replacement part kit "03L198716" is available for changing the control capsule with charge pressure positioner - G581 See electronic parts catalogue (ETKA)
Removal:- Remove the air cleaner housing with air mass meter and connecting pipe- Detach connecting pipe "1" for crankcase breather from the cylinder head cover by pressing the release tabs.
- Uncover the vacuum hoses see arrows - Unscrew screw "2" (undetachable), swing air pipe back with suction pipe anddetach from the turbocharger.
Close the opening on the turbocharger using the sealing cap in the replacement part kit.
- Remove the thermal insulating sleeve surrounding electrical connector "1".
- Detach electrical connector "1" on the position sender for chargepressure positioner "G581".
- Disconnect vacuum hose "2" from the vacuum unit on theturbocharger.
Audi ATU, 8/2010
6 Title or name, division, Date
Replacing turbocharger vacuum units 2.0l CR TDI transversally installed Removal:
- Depending on the design, unscrew and remove securing nut "arrow" for the connection oil supply line/vacuum line on the cylinder head
Note! When loosening the oil supply line, always counterhold the connections.Risk of damage!
- Counterhold connections with custom-built open-end spanner and unscrew and remove oil supply line "arrow" on the turbocharger.
A = 110 mm B = 25 mm
Seal the oil supply hole on the turbocharger with the plugs from the replacement part kit.
Audi ATU, 8/2010
7 Title or name, division, Date
Replacing turbocharger vacuum units 2.0l CR TDI transversally installed Removal:
- Counterhold lock nut "B" with ring spanner "T10423" and unscrew and remove securing nut "A" from the control rod
using plug-in tool "T10422".
- Loosen securing bolts on the vacuum unit "arrow"
and remove vacuum unit "A".
Audi ATU, 8/2010
8 Title or name, division, Date
Replacing turbocharger vacuum units 2.0l CR TDI transversally installed Installation:
Note! Only use new screws and nuts from the replacement part kit!
- Remove lower (if present) securing nuts from the control rod
on the new vacuum unit
- Manually turn locking nut on the control rod as far as it will go
in the direction of the vacuum unit
- Guide control rod through the control lever on the turbocharger,
position vacuum unit "A" and attach the securing bolts
- Tighten securing boltsarrows to 8 Nm
Note:Ensure that the guide moves smoothly on the control rod.
Audi ATU, 8/2010
9 Title or name, division, Date
Replacing turbocharger vacuum units 2.0l CR TDI transversally installed Installation:
- Remove protective cap, place the oil supply line "arrow" on theturbocharger and tighten to 22 Nm.
- Plug in connector "2" on the position sender for charge pressurepositioner -G581- and close heat shield mat
Audi ATU, 8/2010
10 Title or name, division, Date
Replacing turbocharger vacuum units 2.0l CR TDI transversally installed Connect vehicle diagnostic tester and set the vacuum unit control rod:
Select mode: - Press the button for vehicle self-diagnosis on the display
Select vehicle system:- Press the button 01 Engine electronics on the display
- The display shows the control unit identification and coding
for the engine control unit.
Select diagnostic function: - Press the button "011" measured values on the display
- Using the number block enter the measured value block "120"
and confirm the entry by pressing the "Q" key.
- Connect hand vacuum pump "VAS 6213" to the vacuum unit
- While monitoring the lowest value of the measured value block,
set a voltage of 0.760 V by creating a vacuum
During the subsequent setting procedure for the control rod, keep the vacuum and therefore the voltage of 0.760 V constant.
Audi ATU, 8/2010
11 Title or name, division, Date
Replacing turbocharger vacuum units 2.0l CR TDI transversally installed Set the vacuum unit control rod:
- Twist the lock nut "B" down the control rod slowly by hand.
Control lever is at the lowest "stop"
- Counterhold lock nut "B" and twist securing nut "A" on
the control rod against the control lever. Using ring
spanner "T10423", screw on loosely
- Relieve the vacuum in the control unit.
- Monitor the lowest value in the measured block value;
this must settle at a value of 3.303.90 V when depressurised.
- Position the plug-in tool "T10422", counterhold lock nut "B" using ring
spanner "T10423" and tighten securing nut "A".
tighten.
Note! Create a vacuum of 750 50 mbar on the vacuum unit to ensure that the control lever is at the "stop". A voltage of 0.760 V must be generated.
Audi ATU, 8/2010
12 Title or name, division, Date
Replacing turbocharger vacuum units 2.0l CR TDI transversally installed Set the vacuum unit control rod:
Voltage value OK - Press the lock washer onto the control rod by hand and twist it by 90 in the direction of the arrow.
- Seal the control rod/securing nut connection with sealing waxpaint from the replacement part kit.
Voltage value not OK- Counterhold lock nut "B" and loosen securing nut "A" on the control rod; twist locknut "B" to correct the value.
- Counterhold lock nut "B" and turn securing nut "A" in the oppositedirection and tighten with plug-in tool "T10422".
- Press the lock washer onto the control rod by hand and twist it by 90 in the direction of the arrow.
- Seal the control rod/securing nut connection with sealing wax paint from the replacement part kit.
Audi ATU, 8/2010
13 Title or name, division, Date
Replacing turbocharger vacuum units 2.0l CR TDI transversally installed Set the vacuum unit control rod:
- Depending on the design, unscrew and place securing nut "arrow" on the connection oil supply line/vacuum line on the cylinder head and tighten. Remove the sealing cap on the turbocharger
- Finish work on the engine- Start engine and delete fault memory connect vehicle diagnostic, measuring and information "VAS 5051".
- Check setting as follows:
Select basic diagnostic function setting:- Press the button "006" Basic setting on the display - Using the number block enter the measured value block "120"and confirm the entry by pressing the "Q" key
- Press the "Activate" button on the lower half of the screen. - Monitor the values on the lower screen window; must fluctuate
between 0.650.85 V and 3.303.90 V (vacuum unit will move alternately to both end stops).
Voltage values OK exit basic setting!Audi ATU, 8/2010
14 Title or name, division, Date
Replacing turbocharger vacuum units 2.0l CR TDI transversally installedMeasured value block 120: charge pressure positioner
Display value "Charge pressure positioner, monitoring status"XXXX XXX1 Control element opened fullyXXXX XX1X Control element closed fullyXXXX X1XX Learn release for offsetXXXX 1XXX Offset learning activeXXX1 XXXX Opened stop learnt successfullyXX1X XXXX Closed stop learnt successfullyX1XX XXXX Offset learning completed1XXX XXXX Cleaning/verify function active
Display 1 Display 2 Display 3 Display 4
Charge pressure positioner, offsetClosed position
Charge pressure positioner,
Offset Open position,
Charge pressure positioner,
monitoring status
Charge pressure positioner,
Basic voltage position sensor
-10+10% -10+10% XXXX XXXX3.3 3.9 V
0.65 0.85 V
Audi ATU, 8/2010
15 Title or name, division, Date
Replacing turbocharger vacuum units 2.0l CR TDI transversally installedCauses of P0234, P0299 and P2563
- Vacuum hose twisted, kinked leaky/not connected
- Charge pressure hose loose ripped vacuum unit leaky
Audi ATU, 8/2010
16 Title or name, division, Date
Thank you.
ATU Audi Technical UpdatesContents: Technical actionsEngineReplacing turbocharger vacuum units 2.0l CR TDI transversally installedReplacing turbocharger vacuum units 2.0l CR TDI transversally installedReplacing turbocharger vacuum units 2.0l CR TDI transversally installedReplacing turbocharger vacuum units 2.0l CR TDI transversally installedReplacing turbocharger vacuum units 2.0l CR TDI transversally installedReplacing turbocharger vacuum units 2.0l CR TDI transversally installedReplacing turbocharger vacuum units 2.0l CR TDI transversally installedReplacing turbocharger vacuum units 2.0l CR TDI transversally installedReplacing turbocharger vacuum units 2.0l CR TDI transversally installedReplacing turbocharger vacuum units 2.0l CR TDI transversally installedReplacing turbocharger vacuum units 2.0l CR TDI transversally installedReplacing turbocharger vacuum units 2.0l CR TDI transversally installed Measured value block 120: charge pressure positioner Replacing turbocharger vacuum units 2.0l CR TDI transversally installedCauses of P0234, P0299 and P2563Slide Number 16