Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
2014 한국항공우주학회 추계학술대회 2014. 11. 19~21
1 MOTIVATION
2 NUMERICAL APPROACH
3 FIXED WING AIRCRAFT
4 HELICOPTER FUSELAGE
5 CONCLUSION
▮ Helicopter icing
∘ Operating helicopters in icing conditions is particularly dangerous
∘ Blade icing
✓ Rotor blades are especially susceptible to ice growth due to their short chord length
✓ Quick accumulating ice on the rotor systems leads to increased vibration, rapid loss of lift and a large power increase to sustain flight
✓ Shed ice from spinning rotor is common and creates dangerous projectiles
∘ Fuselage icing : considering relatively unimportant parts
✓ Windshield icing will obstruct the pilot’s field of view, making landing and hovering operations difficult
✓ Icing on the nacelle and engine intakes can result in engine failure
✓ Icing on the sensory equipment, antenna, and masts can cause impaired data acquisition
✓ Fuselage icing increases parasite drag, mass, and fuel consumption
∘ Problems to numerical approaches
✓ Flowfield analysis from rotor is essential
✓ 3D effect is dominant contrast to blade with high aspect ratio
▲ Front left of Puma with ice accretion
▲ Air intakes iced-up with clean blades
▲ Ice build-up on the mirrors of Puma
Clean blades
▮ Previous studies
∘ BELL 412 Helicopter(Szilder, K. 2007, 2010*)
✓ With rotor and without rotor
✓ Aerodynamic solver : Euler equation
✓ Impingement model : Lagrangian approach
✓ Thermodynamic model : not used, only rime ice condition
∘ ROBIN body(Fouladi, H. 2013**)
✓ With rotor and without rotor
✓ Aerodynamic solver : Dree’s inflow model in actuator disk model
✓ Impingement model : Eulerian approach
✓ Thermodynamic model : water film model
∘ Limitations of previous study
✓ Low fidelity aerodynamic solver, impingement model, and thermodynamic model
✓ Systematic approach is required in various forward speed
*Szilder, K., "Numerical Simulation of Ice Formation on a Helicopter Fuselage," SAE Technical Paper 2007-01-3308, 2007, doi:10.4271/2007-01-3308. 2013, Fouladi, H., Habashi, W. G., and Ozcer, I. A. Quasi-Steady Modeling of Ice Accretion on a Helicopter Fuselage in Forward Flight, Journal of Aircraft, Vol.50, No.4, pp.1169-1178.**
▲ Droplet trajectories and ice shapes on the fuselage nose*
FEN
SPA-I
CE
▲ Ice accretion shape with FENSAP-ICE**
▮ Numerical approaches to predict ice accretion shapes and its performance
∘ Expensive to operating and maintain costs of experiment
1st generation codes
Limitation of 1st Gen. codes 2nd generation codes
Period 1980~1990s - 1990s~
Aerodynamic solver Panel method, Euler equation
(1) Separation flow of high angle of attack, ice horn, cylinder (2) Prediction of aerodynamic force, especially lack of drag prediction
Navier-Stokes equation
Impingement model Lagrangian approach
No droplet particles in shadow region(flow separation, after ice horn)
Eulerian approach
Thermodynamic mode 2D Messinger model
Sectional approach, axial symmetry problems only
Extended 2D Messinger or 3D water film mode
Representative codes NASA(LEWICE), ONERA, DRA, CIRA
- McGill Univ.(FENSAP-ICE), CIRA(ICECREMO)
▮ Goal of this study
∘ Validation and application of the developed code to 2D and generic 3D icing problems
∘ Comparison of helicopter fuselage icing with various forward flight speed
▮ 4 Models in the platform of open source code(OpenFOAM)
∘ Aerodynamic solver, Impingement model, Thermodynamic model, Ice growth model
∘ Quasi-steady assumption
✓ One or more iterative calculation of each model
✓ Each model assumed to steady state, and field parts(aerodynamic solver, impingement model) are used local time stepping
✓ Fully converged solution conveyed to next model
∘ rhoPimpleFOAM
✓ Navier-Stokes based solver
✓ Unsteady, compressible and turbulent flow
✓ Roughness based S-A model
∘ 3D Eulerian approach
✓ drag, gravity, and buoyancy forces
∘ 3D water film approach
✓ FVM method on the surface water film
∘ 3D surface re-meshing
*Ruff, G. A., and Berkowitz, B. M., “Users Manual for the NASA Lewis Ice
Accretion Prediction Code(LEWICE),” NASA CR-185129, May 1990,
DIANE Publishing, 1990.
Aerodynamic Solver
Impingement Model
Thermodynamic Model
Ice Growth Model
Open source platform
2D
case
, 4 ite
rations
3D
case
, one s
hot(
no ite
ration)
Clean
Final
▮ Validation results of aerodynamic solver
c l
c d
c m
-10 0 10 20-1.5
-1
-0.5
0
0.5
1
1.5
2
0
0.02
0.04
0.06
0.08
0.1
-0.1
-0.05
0
0.05
0.1
0.15
0.2
cm
cl
cd
Cl
Cd
Cm
Experiments[11] Present Method
c
l
cd
cm
-6 -3 0 3 6 9 12 15 18-1.5
-1
-0.5
0
0.5
1
1.5
0
0.03
0.06
0.09
0.12
0.15
-0.1
-0.05
0
0.05
0.1
0.15
0.2
cm
cl
cd
cl
cd
cm
-6 -3 0 3 6 9 12 15-1
-0.5
0
0.5
1
0
0.05
0.1
0.15
0.2
-0.1
-0.05
0
0.05
0.1
0.15
0.2
cm
cl
cd
Clean airfoil*, α=4° Rime ice*, α=4° Glaze ice*, α=4°
*Broeren, P. A., Bragg, M. B., Addy, H. E. Jr., Lee, S., Moens, F., and Guffond, D., “Effect of High Fidelity Ice- Accretion Simulations on Full-Scale Airfoil Performance”, Journal of Aircraft, 47(1): 240-254, 2010, doi: 10.2514 / 1.45203.
▮
x
c f
0 0.2 0.4 0.6 0.8 10
0.005
0.01
0.015
0.02
Hang & Mills ks/L=2.510
4
Hang & Mills ks/L=1010
4
OpenFOAM ks/L=2.510
4
OpenFOAM ks/L=1010
4
▲ Skin friction coefficient of roughened flat plate
▲Heat convection coefficient(right) at roughened airfoil
Sh
c
-0.6 -0.4 -0.2 0 0.2 0.4 0.60
400
800
1200
1600
NASA LEWICE
FENSAP-ICE
Present Method
*Ruff, G. A., and Berkowitz, B. M., “Users Manual for the NASA Lewis Ice
Accretion Prediction Code(LEWICE),” NASA CR-185129, May 1990,
DIANE Publishing, 1990.
-s/c
-0.25-0.2-0.15-0.1-0.0500.050.10.150
0.2
0.4
0.6
0.8
1
Experiment
LEWICE
Present Method
▮
▲Collection efficiency of GLC305*
▲Collection efficiency of NACA64A014*
*Papadakis, M., Hung, K. E., Vu, G. T., Yeong, H. W., Bidwell, C. S., Breer, M. D., and
Bencic, T. J., Experimental Investigation of Water Droplet Impingement on Airfoils,
Finite Wings, and an S-Duct Engine Inlet, NASA Technical Memorandum, 2002.
-s/c
-0.1 -0.05 0 0.05 0.10
0.2
0.4
0.6
0.8
Experiment
LEWICE
Present Method
gravity, and buoyancy drag
▮
➀ ➁ ➂
➀ ➁ ➂ ➃
➀ run in ➀ run out
➁ Impinging water
➂ accumulating ice
➃ heat convection
▮
stop
yes
no no
no
Water & Ice Ice only Water only
yes yes yes
Time step : n+1
Time step : n+1
New surface Surface normal vector
Surface normal vectors at face center
Linear interpolation to nodes
New surface
▮ 3D Grid generation
∘ Linear interpolation from face to point
✓ Face values : ice thickness, surface normal vector
∘ Update surface geometry and re-meshing
▮ Aerodynamic solver
∘ Surface pressure and pressure contour
▮ Impingement model
∘ Collection efficiency and droplet trajectory
▮ Ice accumulated aircraft
▲Top
▲bottom
▲Side
▲Front
1.171m
1.1902m Fuselage : 1.1902m Span : 1.171m Icing Time : 180s Total ice mass : 87.2g
70% Span
50% Span
30% Span
FENSAP-ICE
Present method
10% Span
98% Span
▮ Helicopter fuselage icing*
∘ Aerodynamic solver
✓ The most time consumption step
✓ Helicopter calculation requires calculation costs
⁃ Fixed(Fuselage) and rotating(rotor) parts
✓ Icing code needs many iterations
∘ Actuator disk and actuator surface method
✓ Calculation time efficiency and reliability
Aerodynamic Solver
Impingement Model
Thermodynamic Model
Ice Growth Model
Elliot, J., Althoff, S. L., Sailey, R., “Inflow Measurement Made with a Laser Velocimeter on a Helicopter Model in Forward Flight, Vol. 1. Rectangular Planform Blades at an Advance Ratio of 0.15,” NASA TM 100541, 1987
∘ Same procedures with fixed wing aircraft
▲ Actuator disk model(ADM)
▲ Actuator surface model(ASM)
▮ ADM vs ASM
0o
r/R 180o
Infl
ow
-1 -0.5 0 0.5 1-0.04
-0.02
0
0.02
0.04
0.06
0.08
Experiment
VTM[Kenyon]
Full CFD[Park]
ASM
ADM
270o
r/R 90o
Infl
ow
-1 -0.5 0 0.5 1-0.05
-0.025
0
0.025
0.05
0.075
Experiment
VTM[Kenyon]
Full CFD[Park]
ASM
ADM
x/l
c p
0 0.5 1 1.5 2-0.01
-0.005
0
0.005
0.01
Experiment
ASM
ADM
x
hc
0 0.5 1 1.5 20
20
40
60
80
100
Fuselage only
ADM
ASM
▲ Surface pressure distribution ▲ Heat convection coefficient
▲ longitudinal inflow distribution ▲ Lateral inflow distribution
ADM hub
hub
Pro
pert
ies
on t
he s
urf
ace
ADM
Pro
pert
y in t
he fie
ld
Elliot, J., Althoff, S. L., Sailey, R., “Inflow Measurement Made with a Laser Velocimeter on a Helicopter Model in Forward Flight, Vol. 1. Rectangular Planform Blades at an Advance Ratio of 0.15,” NASA TM 100541, 1987
ADM
ASM
300°
▮
μ=
0
μ=
0.0
75
μ=
0.1
5
ADM ASM ASM ADM
Hig
h sp
eed
Low
speed
Ice accretion shapes
▮ Hovering
ADM ASM
Q>1000 Q>1000
βmax(ASM) > βmax(ADM) , 16%
▮
ADM ASM βmax(ASM) < βmax(ADM) , 2%
Q>1000
Droplets trajectories
ADM ASM
Droplets trajectories
▮
Tip of fuselage Tip of fuselage
ADM ASM βmax(ASM) > βmax(ADM) , 7.3%
▮
ADM ASM
▮ Forward flight speed
∘ Hovering, low speed, and high speed forward flight conditions are simulated
∘ As increasing the forward flight speed, the pattern of ice shapes are different.
✓ Hovering : tail boom and wind shield
✓ Low speed forward flight : fuselage nose and tail boom
✓ High speed forward flight : fuselage nose and wind shield
⁃ The effect of the forward flight speed is more dominant than that of rotor wake
▮ Rotor modeling
∘ Actuator disk model(ADM) and actuator surface models(ASM) are compared
✓ Ice shapes and distribution of collection efficiency are not significantly different qualitatively
✓ Wake body interaction make high collection efficiency
⁃ It is essential to predict the behavior of tip vortex rollup and vortex sheet for accurate wake body interaction
⁃ We consider that the results of ASM are more accurate than those of ADM
• ASM is modeling the behavior of tip vortex and vortex sheets
▮
Elliot, J., Althoff, S. L., Sailey, R., “Inflow Measurement Made with a Laser Velocimeter on a Helicopter Model in Forward Flight, Vol. 1. Rectangular Planform Blades at an Advance Ratio of 0.15,” NASA TM 100541, 1987
◀Fuselage only Rotor+fuselage▶
Rotor wake effect
▮ Helicopter fuselage icing
∘ Without rotor case is heavier than with rotor case
With rotor : 30.0g, less than 20%
Without rotor : 37.8g
Rotor wake effect
▮ Flow field
Low velocity region between rotor and fuselage
High pressure region
◀Fuselage only Rotor+fuselage▶
▮
Straight path of particle impinging Particle can avoid the fuselage
◀Fuselage only Rotor+fuselage▶
Low velocity region
▮ Development of 3D Ice Accretion Code Based on Eulerian approach
∘ 2D problem : Glaze ice(including ice horn), and rime ice condition
✓ Similar accuracy with NASA LEWICE, FENSAP_ICE, and icing wind tunnel tests
∘ Generic 3D problems : DLR-F4(wing and fuselage) cases
✓ Ice heading direction, and maximum thickness are well predicted
∘ Not enough capability around lower surface
✓ Turbulent effect to the impinging model
✓ Heat convection coefficient of lower surface
▮ Rotorcraft fuselage icing problem
∘ Rotor wake effect should be considered – windshield, engine cowl, tail boom icing
✓ Particle trajectories and mass of accumulated ice on the surface are different
∘ As increasing the forward flight speed, the pattern of ice shapes are different.
∘ Predicted ice shapes and distribution of collection efficiency by ASM and ADM are not significantly different qualitatively
✓ Additional research is necessary for quantitative analysis
경청해 주셔서 감사합니다.
▮ View point of an aerodynamicist
∘ There are lots of applicable parts to CFD in aviation safety
∘ AVDL focused on wake vortex turbulence and aircraft icing
▮ Topic 1, Wake vortex turbulence
∘ (1) Development of novel passive equipment, chipped wing tip shape, to attenuate the vortex intensity
✓ A strong counter-rotating vortex is formed at the edge of the chip, which is eventually merged into a single vortex with substantially less strength.
✓ There is a trade-off relationship between increment of drag and the decrement of vortex intensity
∘ (2) Wake vortex warning systems
✓ Research for compatibility of both secure aviation safety and efficient use of airports
✓ Real time visualization of wake vortex from high fidelity NS-LES code and data assimilation method
✓ Proving information of wake hazard area to air traffic controllers
▮ Topic 2, Aircraft icing
∘ (1) Relational Analysis
✓ Lift and drag penalties in glaze ice condition
✓ Moment penalties in rime ice condition
∘ (2) Development of 2nd Generation 3D icing code
✓ 2D problem : Glaze ice(including ice horn), and rime ice condition
⁃ Similar accuracy with NASA LEWICE, FENSAP_ICE, and icing wind tunnel tests
✓ Generic 3D problems : DLR-F4(wing and fuselage) cases
⁃ Ice heading direction, and maximum thickness are well predicted
✓ Rotorcraft fuselage icing prediction
⁃ Rotor wake effect should be considered – windshield, engine cowl, tail boom icing
▮ Aircraft icing
∘ Super-cooled liquid water droplets impact and freeze on the aircraft surface
∘ Aircraft, helicopter, wind turbine blade, ship, and power line
▮ Accumulated ice changes surface roughness, and deforms the wing shapes
∘ Degradation of left, drag and moment performance
∘ Negative to control ability, stall margin, and stall speed
▮ Major cause of aircraft accidents
∘ Aircraft Owners and Pilots Association(AOPA) report : 1990∼2000, 3230 accidents are concerned with weather conditions
∘ 388 accidents(12%) are related to aircraft icing phenomenon
▮ Numerical approaches to predict ice accretion shapes and its performance
∘ Expensive to operating and maintain costs of experiment
▮ Case study(2D ice accretion shapes)
∘ NASA Icing wind tunnel tests*
*1) Wright, W. B., “Validation Results for LEWICE 2.0,” NASA Technical Memorandum, Jan. 1999, pp. 1–679.
IRT case # 308 403 404 405
Airfoil NACA0012
4
102.8 102.8 102.8 102.8
262.04 262.04 256.49 250.3
1.0 0.55 0.55 0.55
20 20 20 20
231 420 420 420
Description Ice horn case Mixture condition Mixture condition Rime ice
IRT shapes
x
y
-0.05 0 0.05 0.1-0.08
-0.06
-0.04
-0.02
0
0.02
0.04
0.06
Experiment1
Experiment2
x
y
-0.04 0 0.04 0.08-0.06
-0.04
-0.02
0
0.02
0.04
Experiment1
Experiment2
x
y
-0.02 0 0.02 0.04 0.06 0.08
-0.06
-0.04
-0.02
0
0.02
Experiment
x
y
-0.02 0 0.02 0.04 0.06 0.08
-0.06
-0.04
-0.02
0
0.02
Experiment
Present Method
NASA LEWICE
x/c
y/c
-0.04 -0.02 0 0.02 0.04 0.06 0.08 0.1-0.06
-0.04
-0.02
0
0.02
0.04
Experiment1
Experiment2
FENSAP_ICE
LEWICE
Present Method
x/c
y/c
-0.04 -0.02 0 0.02 0.04 0.06 0.08 0.1-0.06
-0.04
-0.02
0
0.02
0.04
Experiment1
Experiment2
FENSAP_Oneshot
LEWICE
Present Method
x/c
y/c
-0.04 -0.02 0 0.02 0.04 0.06 0.08 0.1-0.06
-0.04
-0.02
0
0.02
0.04
Experiment
FENSAP_ICE
LEWICE
Present Method
x/c
y/c
-0.04 -0.02 0 0.02 0.04 0.06 0.08 0.1-0.06
-0.04
-0.02
0
0.02
0.04
Experiment
NASA LEWICE
Present Method
▮ Validation results, 4steps Icing limit
Ice heading direction Ice heading direction
Icing limit
Icing limit Icing limit