Page 1

217 Cat D6R EXL Series 111 (Rego No C92401)Model No D6R EXL Series 111

Serial No EXL 00163C9 Engine No THX 09964

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS29/04/10 637.5 Dozer was floated from Hedges Yard 35 $0.00

Yatala to workshop. 35 $0.0029/04/10 Check machine, get ready to fit reverse 35 $0.00

alarm. (Workshop) (PB) 1.25 35 $43.7530/04/10 Fit new LED beacon light, refit hood 35 $0.00 $286.99

lining & check over. 2.5 35 $87.5030/04/10 Fit squark reverse alarm, check over 35 $0.00 $148.50

Fit new fire extinguisher & bracket. 35 $0.00 $166.10(Workshop) (SP) 3 35 $0.00

14/05/10 Travel to Kedron Tunnel, for site induction 35 $0.00Fit new long cab filter, (Was Missing) 35 $0.00 $39.60Unblock grease holes for bottom ripper 35 $0.00pins, Fit nut to bolt on blade arm trunion 35 $0.00 $0.60on back of blade & tighten other bolts, 35 $0.00return to workshop. (GS) 4 35 $140.00

14/05/10 Go to Kedron tunnel & have site induction, 35 $0.00Fit nut to bolt on blade arm front trunion 35 $0.00drop oil off into Robin Roach ute, return 35 $0.00 $17.50to workshop. (TZ) 4 35 $140.00

17/05/10 Load gear, Go to Kedron Tunnel, Fit 35 $0.00new blade corner tips, turn cutting edges, 35 $0.00 $395.18Fit 2 new ripper boots, pins & retainers, 35 $0.00 $215.01Fit 2 new lights to top of cab & wire up, 35 $0.00 $137.28return to workshop. (GS) 8.25 35 $288.75

19/05/10 Go to Truro St Tunnel Job 35 $0.00Change outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76Remove trans & hyd filters, check part 35 $0.00numbers & refit filters 35 $0.00Return to workshop. (GS) 4.5 35 $157.50

21/05/10 Go to Truro St Tunnel Job, repair throttle 35 $0.00return spring. (GS) 4 35 $140.00

25/05/10 Load gear, travel to Truro St, check out 35 $0.00lost bolt from blade arm trunion, travel 35 $0.00to Hastings, pick up new parts, go back 35 $0.00& fit 2 new bolts, nuts, washers & shims 35 $0.00 $103.19to L/h side blade arm trunion, tighten 35 $0.00L/h & R/h side, check beacon light 35 $0.00operation. (GS) 6 35 $210.00

26/05/10 Travel to Truro St & fit 3 new ripper boots, 35 $0.00 $264.003 new pins & retainers return to workshop. 35 $0.00 $58.51

(GS) 3 35 $105.0031/05/10 Go to Truro St tunnel job, remove broken 35 $0.00

radiator grill mounting bolts & fit new 35 $0.00bolts & flat washers, return to workshop. 35 $0.00 $7.36

(GS) 4 35 $140.004/06/10 999 Load gear travel to Truro St Tunnel, 35 $0.00

Fit new cutting edges & end bits to blade 35 $0.00 $985.37with new plow bolts & nuts, 35 $0.00 $110.70Fit 3 new ripper boots with new pins & 35 $0.00 $322.51retainers, Clean down machine, return 35 $0.00to workshop. (GS) 6.25 35 $218.75

35 $0.0035 $0.00

TOTALS 50.75 $1,671.25 $3,291.24 $17.50MACH

Page 2

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS7/06/10 999 Change engine oil & filter 35 $0.00 $45.77 $96.60

" primary fuel filter 35 $0.00 $34.96 " secondary fuel filter 35 $0.00 $28.19 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76 " trans oil & filter & clean screen 35 $0.00 $107.76 $557.66 " hydraulic filters & cover gaskets 35 $0.00 $97.64Blow out A/c evaporator core, 35 $0.00Fit new battery hold down bolts, 35 $0.00 $3.56Fit new bolts in side guards 35 $0.00 $0.96Change ripper boots back to S/h ones. 35 $0.00

(Workshop) (GS 8.5) (DP 7) 15.5 35 $542.507/06/10 Fitting voltage reducer, UHF & music 35 $0.00

radio. (Workshop) (PB) 1 35 $35.008/06/10 Tap out bolt hole for rear trans guard, 35 $0.00

Fill out service sheet & clean up gear. 35 $0.00(GS) 1.5 35 $52.50

8/06/10 Modify transmission rear guard to allow 35 $0.00 $9.40suction screen to removed without 35 $0.00removing guard. (Workshop) (IK) 2.5 35 $87.50

8/06/10 Finish fitting voltage reducer, UHF & 35 $0.00 $504.23music radio. (Workshop) (PB) 3.5 35 $122.50

8/06/10 Fit rear trans guard & straighten frame 35 $0.00 $4.48on top of blade. (Workshop) (PB) 2 35 $70.00

9/06/10 Weld grouser bar to side cutters of 35 $0.00 $167.75blade. (Workshop) (IK) 5.5 35 $192.50

15/06/10 Detail cab of dozer. " (DW) 0.5 35 $17.5016/06/10 Cut & weld wear plates onto blade side 35 $0.00 $347.99

arms. (Workshop) (IK) 6 35 $210.0029/06/10 Fit new throttle return spring, grease 35 $0.00 $22.90

machine & check over. (Workshop) (GS) 1.5 35 $52.5012/07/10 Go to Kerkin Rd, fit new fire extinguisher, 35 $0.00

remove & fit new screw end for U.H.F 35 $0.00radio aerial lead, return to workshop. (TZ) 1 35 $35.00

9/08/10 1127 Wash dozer. (Workshop) (SW) 2.75 35 $96.251/09/10 1128 Wash dozer. (Workshop) (DW) 1 35 $35.0015/09/10 Wash down dozer. (Workshop) (DW) 1.25 35 $43.751/11/10 1282 Change engine oil & filter 35 $0.00 $33.93 $101.64

" fuel water seperator filter 35 $0.00 $34.96 " secondary fuel filter 35 $0.00 $28.19 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76Check all fluid levels. 35 $0.00

(Wacol Job Site) (GS) 1.25 35 $43.751/11/10 Change outer air filter, cab & fuel filter, 35 $0.00

fill engine oil & check final drives, return 35 $0.00to workshop from Wacol Job Site. (PB) 1.25 35 $43.75

22/12/10 Mounting plates on blade for G.P.S poles. 35 $0.00 $10.90(Workshop) (IK) 5.5 35 $192.50

6/01/11 Make up bracket for G.P.S unit in cab. 35 $0.00(Workshop) (IK) 2 35 $70.00

10/01/11 Remove shims from blade joints, 35 $0.00Grease machine, Check oils & top up, 35 $0.00 $12.71Wash machine. (Workshop) (PB) 6 35 $210.00

24/01/11 Fuel up machine at Upper Coomera & 35 $0.00return to workshop. (GS) 0.75 35 $26.25

35 $0.00TOTALS 113 $3,850.00 $4,875.49 $786.11

MACHDATE HRS DESCRIPTION LAB RATE COST PARTS OILS

Page 3

2/02/11 Go to Rose Valley Dr & repair U.H.F 35 $0.00radio wire. (GS) 0.75 35 $26.25

9/02/11 1489 Load service gear, Go to Rose Valley Dr 35 $0.00Change engine oil & filter 35 $0.00 $45.41 $101.64 " fuel water seperator filter 35 $0.00 $34.96 " secondary fuel filter 35 $0.00 $28.05 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76 " hydraulic oil filters 35 $0.00 $81.27Check over. (GS 3) (DP 3) 6 35 $210.00

14/03/11 Load up, Go to Upper Coomera, Turn 35 $0.00cutting edges & fit new end bits, return 35 $0.00 $392.61to workshop & unload. (DP 3) (RS 3) 6 35 $210.00

30/03/11 1771.6 Load up, Go to Upper Coomera, check 35 $0.00vandal damage, remove rear hood lining 35 $0.00to trace ripped out wiring, Refitted 35 $0.00wiring & earths, Refitted lining & speakers 35 $0.00Repaired wiring to UHF radio & loom to 35 $0.00radio, Fit new UHF radio, removed 35 $0.00 $216.70voltage reducer, repaired wiring & 35 $0.00refitted, Wired up new radio & fitted, 35 $0.00 $138.60Fitted new hood lining, Tested radio's 35 $0.00 $183.87(OK) returned to workshop. (NB) 6 35 $210.00

31/03/11 1771 Load service gear, Go to Riverstone 35 $0.00Estate Upper Coomera, 35 $0.00Change engine oil only 35 $0.00 $101.64 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76Check final drive oils 35 $0.00Check over, return to workshop. (GS) 4 35 $140.00

12/05/11 Go to Eggersdorf Rd & change grease 35 $0.00nipple on L/h ripper pin, return to 35 $0.00 $0.80workshop. (SW) 0.75 35 $26.25

31/05/11 2006.1 Change engine oil & filter 35 $0.00 $43.99 $101.64 " fuel water seperator filter 35 $0.00 $35.49 " secondary fuel filter 35 $0.00 $28.05 " inner air filter 35 $0.00 $52.15 " outer air filter 35 $0.00 $23.58 " cab air filter 35 $0.00 $26.76 " trans oil & filter 35 $0.00 $111.42 $557.66 " hydraulic oil & filter 35 $0.00 $77.22 $171.70 " final drive oils 35 $0.00 $101.79

(Workshop) (GS) 6.75 35 $236.2531/05/11 2006 Clean out main ripper mount pin hole to 35 $0.00

take grease, align final drive bung holes 35 $0.00for draining. (Workshop) (TZ) 1 35 $35.00

1/06/11 2006 Flush L/h final drive, 35 $0.00 $40.32Fit 4 new wiper blades & clean down 35 $0.00 $6.00

(Workshop) (GS) 3 35 $105.007/06/11 Fit Rego number plates. (C92401) 35 $0.00

(Workshop) (PB) 0.5 35 $17.50 $890.7821/06/11 Wash dozer. (Workshop) (SW) 0.5 35 $17.5021/06/11 Fit new set of cutting edges & end bits, 35 $0.00 $890.78

fit new bolts, nuts & flat washers. 35 $0.00 $133.44(Workshop) (SW) 2 35 $70.00

21/06/11 Replace blocked grease nipple on ripper 35 $0.00 $0.80linkage. (Workshop) (SW) 0.5 35 $17.50

TOTALS 150.8 $5,171.25 $8,459.22 $1,922.18MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS23/06/11 2063.4 Check metal in L/h final drive, put dozer 35 $0.00

Page 4

in workshop, break L/h track & remove 35 $0.00L/h final drive, dismantle & check parts 35 $0.00found bearings in planet gears loosing 35 $0.00hardfacing. (GS) 5 35 $175.00

24/06/11 2063.4 Clean up final drive parts, assemble L/h 35 $0.00final drive with new bearings & seals, 35 $0.00 $1,033.31tap out damaged thread in frame for 35 $0.00final drive housing mounting bolt, 35 $0.00Fill L/h final drive oil, join up track & 35 $0.00 $52.78adjust, top up trans oil. (GS) 8.5 35 $297.50 $7.54

24/06/11 Assemble L/h final drive & planetary sets 35 $0.00with new bearings & seals, fit to machine, 35 $0.00join track & adjust, finish off. 35 $0.00

(Workshop) (PB) 3.75 35 $131.2528/07/11 Go to Holcim Quarry Peachey Rd & 35 $0.00

check out crack in L/h trackframe, 35 $0.00return to workshop. (PB) 1 35 $35.00

8/08/11 2252.7 Gouge & weld crack in L/h track frame 35 $0.00(Workshop) (PB) 1 35 $35.00

8/08/11 2252.7 Change engine oil only 35 $0.00 $104.72 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76Top up wheel outer pivot bearing oil 35 $0.00Check over, tighten cutting edge bolts, 35 $0.00Fit 2 new sealed beam to work lights. 35 $0.00 $56.10

(Workshop) (DP 1.5) (SW 2.5) 4 35 $140.008/08/11 Travel to Beenleigh Beaudesert Rd 35 $0.00

Beenleigh & tighten tilt ram hoses & 35 $0.00replace 1 oring, return to workshop. (DP) 1 35 $35.00 $0.84

11/08/11 Travel to Beenleigh Beaudesert Rd 35 $0.00Beenleigh, check & adjust reverse alarm. 35 $0.00

(GS) 1.5 35 $52.5019/08/11 Fuel up machine at workshop on back of 35 $0.00

float with trader fuel truck. (MK) 0.25 35 $8.7524/08/11 Travel to Hope Island & remove G.P.S 35 $0.00

poles from top of blade, move machine 35 $0.00into position ready to be shifted, clean 35 $0.00out tracks, help position float & load, 35 $0.00return to workshop. (TZ) 2 35 $70.00

4/10/11 Travel to Cova 130 & fit GPS poles to 35 $0.00blade. (TZ) 0.75 35 $26.25

14/10/11 2536 Change engine oil & filter 35 $0.00 $43.99 $104.72 " fuel water seperator filter 35 $0.00 $35.49 " secondary fuel filter 35 $0.00 $28.05 " outer air filter (New) 35 $0.00 $56.91 " cab air filters 35 $0.00 $26.76 " trans filter 35 $0.00 $105.89 " hydraulic oil filters 35 $0.00 $77.22Check over. (GS 1.25) (JO 1.25) 2.5 35 $87.50

1/12/11 Go to Stapylton, remove floor plates, 35 $0.00Find oil leak, Drop rear belly plate, 35 $0.00(Blowen test point hose), Cap fitting, refit 35 $0.00belly & floor plates, return to w/shop.(PB) 2 35 $70.00

1/12/11 Travel to Quinns Hill Rd, top up trans (GS) 1 35 $35.00 $120.9035 $0.0035 $0.00

TOTALS 185 $6,370.00 $9,974.12 $2,312.84MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS9/02/12 Check over machine for work, grease 35 $0.00

machine & fuel up. (Workshop) (GS) 1 35 $35.00

Page 5

9/02/12 Clean down machine, checked over & 35 $0.00greased. (Workshop) (SW) 2 35 $70.00

14/02/12 Travel to Biddadabar and remove GPS pole 35 $0.00Return to workshop (SW) 2 35 $70.00

15/02/12 Travel to Yatala and re erect GPS pole 35 $0.00 (SW) 1 35 $35.00

16/02/12 Repair shovel handle and take to machine 35 $0.00 (SW) 0.5 35 $17.50

23/02/12 2773 Load service gear, travel to Yatala 35 $0.00Change engine oil & filter 35 $0.00 $16.02 $102.85 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76Flush oil in outer ends of equalizer bar 35 $0.00Check final drive oils, (Metal in R/h side) 35 $0.00Top up hydraulic oil (1 Lt 15W/40) 35 $0.00 $3.74Check over, return to workshop. (GS) 3.5 35 $122.50

1/03/12 Travel to Cuthbert Drive Ormeau & 35 $0.00tighten A/c belt, return to workshop. 35 $0.00

(GS .25) (SW .25) 0.5 35 $17.504/04/12 Travel to Cuthbert Drive Ormeau & 35 $0.00

install new music radio aerial. (DP) 0.25 35 $8.75 $22.9210/04/12 Pirtek Yatala Hose travelled to Cuthbert 35 $0.00

Drive Ormeau & removed & replaced 35 $0.00blown hydraulic hose, (Hose was rubbing 35 $0.00 $284.33on bracket in belly of machine. 35 $0.00

23/04/12 Load gear, travel to Cuthbert Drive 35 $0.00Ormeau & fit new end bits & turn cutting 35 $0.00 $341.00edges, fit full set of cutting edge bolts & 35 $0.00 $52.03nuts. (TZ) 2 35 $70.00

22/05/12 3087 Change engine oil & filter 35 $0.00 $43.37 $104.72 " fuel water seperator filter 35 $0.00 $35.77 " secondary fuel filter 35 $0.00 $28.05 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76 " trans oil & filter 35 $0.00 $17.61 $596.44 " hydraulic filters, top up oil (2 lts) 35 $0.00 $75.48 $7.48

(Workshop) (GS) 3.5 35 $122.5023/05/12 Finish 1000 hr service. (Workshop) (GS) 6 35 $210.0024/05/12 Perform check list. (Workshop) (TS) 0.5 35 $17.5024/05/12 Weld up crack in R/h track frame. 35 $0.00

(Workshop) (DP) 1.5 35 $52.5030/05/12 Cut off bent rock guards, straighten & 35 $0.00

re-weld on. (Workshop) (SW) 1.5 35 $52.5030/05/12 Tidy up machine, straighten top of blade 35 $0.00

& touch up paint work. (Workshop) (DP) 2.5 35 $87.5030/05/12 Fit new cab floor mat. 35 $0.00 $182.52

(Workshop) (David Keane) 1 35 $35.0031/05/12 Reassemble painted bracket & mount 35 $0.00

fire extinguisher (Workshop) (DP) 1 35 $35.001/06/12 Remove track plates & fit good S/h plates 35 $0.00 $56.47

with good S/h track bolts. 35 $0.00(Workshop) (GS 8.5) (SG 5) 16 35 $560.00

(Workshop) (TS 2.5) (MW 2.75) 5.25 35 $183.7535 $0.0035 $0.00

TOTALS 236.5 $8,172.50 $11,230.37 $3,128.07MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS4/06/12 3087 Swap track plates, fit new bolts to track 35 $0.00 $33.44

joiners, Top up hyd oil (5.5 Lts 15W/40), 35 $0.00 $20.57Clean up work area. (Workshop) (GS) 3 35 $105.00

Page 6

4/06/12 Assist Greg with plates (Workshop) (SW) 2 35 $70.005/06/12 Clean, prepare & paint track gear, blade 35 $0.00 $50.34

& blade arms. (Workshop) (TS) 2.75 35 $96.256/06/12 Cut lengths of grouser bar for track 35 $0.00 $1,234.20

plates & start fitting. (Workshop) (PB) 3.5 35 $122.50 7/06/12 Welding grouser bar to track plates 1 35 $35.00

removed from machine. (Workshop) (PB) 35 $0.00 7/06/12 Relugging grouser plates. " (IK) 1 35 $35.008/06/12 Tacking grouser bars onto track plates, 35 $0.00

cut rest of grouser bar to lengths. (PB) 5 35 $175.008/06/12 Re-lugging grouser plates. (IK) 6 35 $210.0012/06/12 Tacking grouser bars onto track plates 35 $0.00

& weld up ends. (PB) 5.5 35 $192.5012/06/12 Re-lugging grouser plates. (IK) 9 35 $315.0013/06/12 Re-lugging grouser plates. (IK) 3.5 35 $122.50 $236.9518/06/12 3110 Clean down machine, check engine, 35 $0.00

trans & hyd oil levels, check coolant, 35 $0.00check over, fit new rego sticker & clean 35 $0.00up wash bay. (Workshop) (GS) 4.5 35 $157.50

8/08/12 All Diesels fitter travelled to Riverstone 35 $0.00 $236.50Crossing & check A/c system not getting 35 $0.00cold, found heater valve not closed off, 35 $0.00Removed dash panels & adjusted cable 35 $0.00and tested. 35 $0.00

14/08/12 3301 Travel to Riverstone crossing & 35 $0.00Change outer air filter, return to 35 $0.00 $57.41workshop, (51 Kms travel costs from 35 $0.00 $76.50workshop to Riverstone crossing & 35 $0.00return to workshop). (GS) 1 35 $35.00

15/08/12 3313 Load service gear travel Riverstone 35 $0.00Crossing 35 $0.00Change engine oil only 35 $0.00 $102.85 " cab air filters 35 $0.00 $26.76Check equalizer bar outer end oils, 35 $0.00Check over & return to workshop, 35 $0.00(51 Kms travel costs from workshop to 35 $0.00 $89.25Riverstone Crossing & return to 35 $0.00workshop). (GS) 3 35 $105.00

3/10/12 Travel to Beechmont & fit new bolt to 35 $0.00 $2.87R/h side ripper mount pin, return to 35 $0.00workshop, (95 Kms travel costs from 35 $0.00workshop to Beechmont & return). (PB) 2 35 $70.00

24/10/12 3669 Load service gear travel to Beechmont 35 $0.00Change engine oil & filter 35 $0.00 $44.39 $104.72 " fuel water seperator filter 35 $0.00 $35.77 " main fuel filter 35 $0.00 $28.06 " outer air filter 35 $0.00 $23.28 " cab air filters 35 $0.00 $26.76 " hydraulic oil filter 35 $0.00 $88.77Check final drive oils 35 $0.00Grease equalizer bar ends 35 $0.00Check over dozer & return to workshop. 35 $0.00

(GS) 4.5 35 $157.5035 $0.00

TOTALS 293.8 $10,176.25 $13,521.62 $3,356.21MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS6/11/12 Hastings Deering fitter travelled to 35 $0.00 $1,052.39

Ormeau workshop to repair auto blade 35 $0.00control, operated machine & found quick 35 $0.00drop only worked at high idle and after 35 $0.00

Page 7

machine had been operated for several 35 $0.00minutes, turned machine off and operated 35 $0.00implements after 30 seconds, finding that 35 $0.00implement didn’t move, connected gauge 35 $0.00to pilot accumulator and found no 35 $0.00precharge pressure, removed 35 $0.00accumulator and connected nitrogen 35 $0.00regulated to 150 psi, Accumulator would 35 $0.00not hold charge and leaked out through 35 $0.00bladder, charged new accumulator with 35 $0.00150 Psi of nitrogen, fitted & tested 35 $0.00operation, Quick drop now operated 35 $0.00correctly and implements could be moved 35 $0.00several minutes after engine had been 35 $0.00switched off. 35 $0.00

21/11/12 Perform weed & seed, detail,check over 35 $0.00and fuel up. Replace cab filters 35 $0.00

(Workshop) (TS) 3.25 35 $113.7523/11/12 Fit retaining bolts to ripper mounting pins. 35 $0.00

(Workshop) (GS) 0.5 35 $17.5023/11/12 Straighten bars on top of blade. 35 $0.00

(Workshop) (M Schwenke) 0.5 35 $17.5026/11/12 Travel to Sitech at Bowen Hills and pick 35 $0.00

up GPS gear and deliver to site at River- 35 $0.00Stone Crossing (TS) 3.5 35 $122.50

27/11/12 Deliver GPS cables to Riverstone 35 $0.00Crossing (TS) 1 35 $35.00

5/12/12 Deliver 2 x o-rings to operator at 35 $0.00 $9.26Riverstone Crossing (SG) 0.5 35 $17.50

10/12/12 3832 Load service gear travel to Riverstone Cr 35 $0.00Change engine oil only 35 $0.00 $104.72 " outer air filter 35 $0.00 $23.58 " cab filters 35 $0.00 $26.76Check over, return to workshop, 35 $0.00(52 Kms travel costs from workshop to 35 $0.00Riverstone Crossing & return to 35 $0.00workshop). (GS) 3 35 $105.00

10/12/12 Travel to Riverstone Crossing and fit new 35 $0.00 $1,096.07cutting edges and end bits (SG) 1.5 35 $52.50

3/01/13 Travel to Mazda site to check codes on 35 $0.00machine.Unable to repairso called in Cat 35 $0.00Serviceperson (DP) 1.75 35 $61.25

15/01/13 Dismantle starter motor,check brushes. 35 $0.00Remove armature and test OK .Windings 35 $0.00burnt out.Find another dismantled starter 35 $0.00off bench and make one up. Install new 35 $0.00brushes and change gear to fit D6 Dozer. 35 $0.00

(Workshop) (SG) 5 35 $175.0012/02/13 4026 Travel to Gilston & tighten fan, alt & A/c 35 $0.00

belts, return to workshop, (69 Kms travel 35 $0.00 $120.75costs from workshop to Gilston & return). 35 $0.00

(GS) 1.75 35 $61.2535 $0.00

TOTALS 316 $10,955.00 $15,850.43 $3,460.93MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS14/02/13 Travel to Gilston & clean around hyd 35 $0.00

pump suction at tank & find oil leak, 35 $0.00return to workshop & get parts ordered, 35 $0.00(62 Kms travel costs from workshop to 35 $0.00 $108.50Gilston & return). (PB) 1.75 35 $61.25

Page 8

15/02/13 4016 Load service gear travel to Gilston, 35 $0.00Change engine oil & filter 35 $0.00 $44.39 $104.72 " fuel water seperator filter 35 $0.00 $35.77 " secondary fuel filter 35 $0.00 $28.06 " outer air filter (New) 35 $0.00 $57.41 " inner air filter (New) 35 $0.00 $79.23 " cab fresh air filter (Washed) 35 $0.00 $17.78 " cab inner air filter (Washed) 35 $0.00 $8.98 " trans oil & filter 35 $0.00 $105.31 $596.44 " hydraulic oil & filters 35 $0.00 $75.02 $179.52Check over, return to workshop, unload, 35 $0.00Perform paper work. (96 Kms travel costs 35 $0.00 $168.00from workshop to Gilston & return). (GS) 6.5 35 $227.50

25/02/13 Unload machine & put in wash bay, Get 35 $0.00ready to remove L/h final drive, put 35 $0.00machine in workshop, remove & 35 $0.00dismantle L/h final drive, remove planet 35 $0.00gears & bearings (Gear bearings US), 35 $0.00remove R/h final drive planet carrier, 35 $0.00remove gears & bearings (Same disease 35 $0.00as L/h side, Remove floor plates, panels 35 $0.00and filter housing to get to hydraulic pump 35 $0.00suction. (PB) 6 35 $210.00

25/02/13 Remove L/h track & final drive and 35 $0.00dismantle. (Workshop) (TZ) 2 35 $70.00

25/02/13 Clean track frame for fitters (W/shop) (TS) 1.25 35 $43.7526/02/13 Fit new hyd pump suction steel pipe, 35 $0.00 $871.91

assemble R/h final drive planetary with 35 $0.00new bearings and fit to machine, fit new 35 $0.00 $289.68axle shaft seals to both final drives, 35 $0.00 $28.80Assemble L/h planetary with new gear 35 $0.00bearings, assemble L/h final drive, fit 35 $0.00 $289.68new duo-cone oring seals & fit to machine 35 $0.00 $32.96

(Workshop) (PB) 9 35 $315.0026/02/13 Clean up final drive parts, assemble & fit 35 $0.00

to machine, fill L/h side & R/h side with 35 $0.00new oil & join up L/h side track. (GS) 7 35 $245.00 $108.00

27/02/13 Grease machine, check cannon & 35 $0.00track frame pivot oils, check over 35 $0.00machine. (Workshop) (GS) 1 35 $35.00

27/02/13 Put machine in wash bay, clean up from 35 $0.00job, fit new fuel tank sensor kit, calibrate 35 $0.00 $60.12direction switches & reun clutch 35 $0.00calibration, check trans accumulator, 35 $0.00(Over pressure- release to specifictions) 35 $0.00

(Workshop) (PB) 5.5 35 $192.502/04/13 Cut & weld on old cutting edge for blade 35 $0.00

side wear plates. 35 $0.00(M Schwenke) 6 35 $210.00

3/04/13 Hardface edging on blade side wear 35 $0.00plates (Workshop) (MS) 7 35 $245.00

35 $0.00TOTALS 369 $12,810.00 $18,152.03 $4,449.61

MACHDATE HRS DESCRIPTION LAB RATE COST PARTS OILS5/04/13 Remove & dismantle trans accumulator, 35 $0.00

fit new seal kit & re-charge with nitrogen 35 $0.00 $183.18and refit to machine. (Workshop) (PB) 2 35 $70.00

17/04/13 4123.5 Travel to Foxwell Rd, found transmission 35 $0.00hose blown, removed floor, removed & 35 $0.00replaced hose with one from Enzed Hose 35 $0.00 $1,113.37

Page 9

Van, replaced a second hose nearly 35 $0.00rubbed through as well, moved machine 35 $0.00to level ground checked & topped up 35 $0.00transmission oil, (40 Lts 30 oil), returned 35 $0.00 $160.80to workshop, (36 Kms travel costs from 35 $0.00 $54.00workshop to Coomera & return). 35 $0.00

(Jake B) 6 35 $210.006/06/13 Fit new wiper blade. 35 $0.00 $2.75

(Highland Reserve Upper Coomera) (SG) 0.25 35 $8.757/06/13 4367 Load service gear travel to Rose Valley 35 $0.00

Way Upper Coomera 35 $0.00Change engine oil & filter 35 $0.00 $39.96 $104.72 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76Check over, return to workshop, 35 $0.00(48 Kms travel costs from workshop to 35 $0.00 $84.00Upper Coomera & return). (GS) 2.5 35 $87.50

16/07/13 4480.7 Perform weed and seed clean 35 $0.00(Workshop) (Terry S) 3.75 35 $131.25

17/07/13 4480 Change engine oil & filter 35 $0.00 $39.96 $104.72 " fuel water seperator filter 35 $0.00 $40.77 " main fuel filter 35 $0.00 $26.65 " inner air filter (New) 35 $0.00 $57.23 " outer air filter (Washed) 35 $0.00 $23.58 " hydraulic filters 35 $0.00 $75.02Adjust tracks & check over machine. 35 $0.00

(Workshop) (Jake B) 3 35 $105.0017/07/13 4481.3 Detail and clean oil spill off machine. 35 $0.00

(Workshop) (Terry S) 2.5 35 $87.5012/08/13 4659 Load service vehicle with hammer and 35 $0.00

generator and go to Toowoomba Range 35 $0.00and remove jammed rock from track frame 35 $0.00

(Sam W) 3.5 35 $122.5024/08/13 4757 Travel to Toowoomba Range Job Site 35 $0.00

Change engine oil and filter 35 $0.00 $39.96 $104.72 " outer air filter 35 $0.00 $63.14 " cab air filters 35 $0.00 $26.76Top up transmission oil (5 Lts 30) 35 $0.00 $20.10Repair broken cab light wires 35 $0.00Drop off gear, return to workshop, 35 $0.00(332 Kms travel costs from workshop to 35 $0.00 $581.00Toowoomaba & return), (2x Loganlea tolls 35 $0.00 $8.30& 2x Heathwood tolls). (GS) 35 $0.00 $13.62

6/09/13 Travel to Toowoomba Range Job Site and 35 $0.00replace GPS Pole (Kurtis A) 2 35 $70.00282 Kms return, 2x Loganlea & 2x 35 $0.00Heathwood Tolls 35 $0.00 $429.06

35 $0.0035 $0.0035 $0.0035 $0.00

TOTALS 394.5 $13,702.50 $21,104.68 $4,944.67MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS9/09/13 4947 Diagnose warm A/c fault, found heater 35 $0.00

valve to be faulty, returned home from 35 $0.00Toowoomaba), (168 Kms travel costs 35 $0.00 $252.00from Toowoomba Range home), 3 35 $105.00(1x Heathwood toll charge & 1x Loganlea 35 $0.00 $6.21charge 35 $0.00

11/09/13 Prepare service & check and order parts. 35 $0.00

Page 10

(Workshop) (GS) 0.5 35 $17.5011/09/13 4987 Travel to Toowoomba Range, diagnose 35 $0.00

and repair multiple faults in A/c wiring, 35 $0.00return home. (253 Kms travel costs from 35 $0.00 $379.50workshop to Toowoomba Range and 35 $0.00return home), (2 Loganlea tolls & 2x 35 $0.00 $4.70Heathwood tolls). (M. Brown) 7.5 35 $262.50 $7.72

12/09/13 Looked up fault codes and talked to 35 $0.00Hastings deering tech support, results 35 $0.00were in-conclusive. 35 $0.00

(M. Brown) 2 35 $70.0012/09/13 Prepare gear to perform jobs. 35 $0.00

(Workshop) (GS) 0.5 35 $17.5013/09/13 5027 Travel to Toowoomba Range, 35 $0.00

Change engine oil & filter 35 $0.00 $39.96 $104.72 " primary fuel filter 35 $0.00 $41.39 " secondary fuel filter 35 $0.00 $26.65 " outer air filter 35 $0.00 $63.14 " inner air filter 35 $0.00 $56.19 " cab air filters 35 $0.00 $26.76 " trans oil & filter 35 $0.00 $104.43 $596.44 " hydraulic filters 35 $0.00 $78.12Turn cutting edges & fit new end bits, 35 $0.00 $343.46Check over, return to workshop, 35 $0.00(294 Kms travel costs from workhsop to 35 $0.00Toowoomba Range and return), 35 $0.00(2x Loganlea tolls & 2x Heathwood tolls). 35 $0.00

(GS 9) (R Armstrong 9) 18 35 $630.0017/09/13 5036 Travel to Toowoomba Range via 35 $0.00

Hastings Deering and fit re-manufactured 35 $0.00water pump & seals, return to workshop. 35 $0.00 $389.04

(SW 7) (R. Armstrong 8.25) 15.5 35 $542.509/10/13 Put pin in bolt hole for L/h side ripper box 35 $0.00

pin, removed tilt cylinder guard, Replace 35 $0.002 way plug. (Toowoomba Range) (SW) 1 35 $35.00

11/10/13 Get filters out ready for service. 35 $0.00(Workshop) 35 $0.00

21/10/13 5310 Travel to Toowoomba Range & 35 $0.00Perform 250 Hr service, 35 $0.00Change engine oil & filter 35 $0.00 $39.96 $104.72 " primary fuel filter 35 $0.00 $41.39 " secondary fuel filter 35 $0.00 $26.65 " inner air filter (New) 35 $0.00 $57.23 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76Fit 2 new N150 batteries 35 $0.00 $547.80Tighten A/c compressor drive belt, 35 $0.00Repair roof light, 35 $0.00Grease machine, Return to workshop. 35 $0.00

(R. Armstrong) 9 35 $315.00TOTALS 451.5 $15,697.50 $23,687.32 $5,750.55

MACHDATE HRS DESCRIPTION LAB RATE COST PARTS OILS21/10/13 5310 Travel to Toowoomba Range, perform 35 $0.00

welding repair & plate blade, return to 35 $0.00 $45.42workshop. (KA) 5.5 35 $192.50

22/10/13 Clean up after service. 35 $0.00(Workshop) (R Armstrong) 0.5 35 $17.50

2/12/13 Unload & put machine in workshop, 35 $0.00remove blown battery & finding terminals 35 $0.00to make new joiner strap. 35 $0.00

Page 11

(Workshop) (PB) 0.75 35 $26.253/12/13 5365.8 Fit good S/h battery, Make up new joiner 35 $0.00

stap, Straighten, remove broken bolts & 35 $0.00refit blade tilt cylinder guard, Weld up top 35 $0.00 $15.40of L/h track frame behind recoil housing, 35 $0.00Fit new bolt & nyloc nut to L/h bottom 35 $0.00 $4.18ripper mount pin, get ripper pins greasing 35 $0.00and grease machine, Check engine oil 35 $0.00(Nothing on dipstick with engine running), 35 $0.00Top up engine oil (6 Lts 15W/40), 35 $0.00 $22.44Check trans fault (Output speed sensors), 35 $0.00Check sensors & wiring to plug under 35 $0.00fuel tank, (OK), (Found broken wire from 35 $0.00plug under fuel tank to ECM). 35 $0.00

(Workshop) (PB) 8 35 $280.004/12/13 6366 Remove seat & base & floor plates & 35 $0.00

side panel, run new wire replacing green 35 $0.00901 from plug under fuel tank to ECM 35 $0.00(Wire for trans output speed sensor) 35 $0.00Refit panels, plates & seat etc 35 $0.00Fit new LED beacon light with mounting 35 $0.00 $248.95pattern different), Get lights working & 35 $0.00 $10.78remove bridging power supply for A/c 35 $0.00after re-setting circuit breaker, (Was 35 $0.00getting feed back to ignition, wouldn't 35 $0.00turn off). (Workshop) (PB) 9 35 $315.00

5/12/13 Remove shims from blade arm caps, 35 $0.00test drive & park machine outside 35 $0.00workshop. (PB) 1.25 35 $43.75

5/12/13 5366.5 clean and detail machine (Workshop) (TS) 3 35 $105.006/12/13 Finish detail and check over machine 35 $0.00

(Workshop) (Terry S) 0.5 35 $17.5017/01/14 Collect required filters and gear and take 35 $0.00

to site at Toowoomba (Terry S) 5 35 $175.006/02/14 5514 Load service gear travel to Toowoomba 35 $0.00

Change engine oil & filter 35 $0.00 $39.96 $104.72 " fuel water seperator filter 35 $0.00 $41.39 " secondary fuel filter 35 $0.00 $26.65 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76 " hydraulic filters 35 $0.00 $78.12Fit S/h UHF mike. 35 $0.00(145 Kms travel costs from workshop to 35 $0.00 $253.75Toowoomba Range), (1x Loganlea toll & 35 $0.00 $4.151x Heathwood toll Charge). (GS) 5 35 $175.00 $6.81

6/02/14 5514 Assist Greg with service and repair top 35 $0.00work light (Ron A) 4.5 35 $157.50

35 $0.0035 $0.00

TOTALS 494.5 $17,202.50 $24,513.22 $5,877.71MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS14/03/14 5890 Travel to dozer from Tilly's to Toowoomba 35 $0.00

Range Job Site, 35 $0.00Change engine oil & filter 35 $0.00 $39.56 $104.72 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76Fit new fan belts 35 $0.00 $198.10Fit new light bulb 35 $0.00 $13.86Return back to workshop. 35 $0.00

(GS 5.5) (Doug Oslar 5.5) 11 35 $385.00

Page 12

24/03/14 Supplied new UHF (Dean P ) 35 $0.00 $199.201/04/14 5859 Travel to Toowoomba Range Job Site and 35 $0.00

inspected engine oil leak, remove belly 35 $0.00plate and found engine sump cracked on 35 $0.00the bottom, removed sump and travelled 35 $0.00to Hastings deering Toowoomba for 35 $0.00new sump & gasket, returned to dozer 35 $0.00cleaned up and fitted new sump & gasket, 35 $0.00 $698.35Filled engine oil and tested for leaks all 35 $0.00 $104.72(OK), refitted all belly plates, cleaned up 35 $0.00area, recheck oil level and sent dozer 35 $0.00to work, returned home. (Jake B) 13.5 35 $472.50

8/04/14 6052 Travel to Toowoomba, inspect for noise 35 $0.00in engine, remove turbo boost hose, 35 $0.00drive around Toowoomba for parts, pick 35 $0.00clamps from Brown & Hurley acquired 35 $0.00through Hastings, return to doxer and 35 $0.00re-fit boost hose with 4 new clamps, 35 $0.00 $64.72return to workshop, (340 Kms travel costs 35 $0.00 $510.00from Workshop to Toowoomba & return) 35 $0.00(2x Loganlea tolls & 2x Heathwood tolls). 35 $0.00 $12.42

(Doug Oslar) 9.25 35 $323.759/04/14 Travel to Toowoomba Range and replace 35 $0.00

missing corner tip bolts & weld up crack 35 $0.00 $18.88in track frame, return to workshop. 35 $0.00

(KA) 5.5 35 $192.5017/04/14 6064 Travel to Toowoomba ansd perform 2000 35 $0.00

hr service (Greg S. 8.5)(Mitch C 8.5) 17 35 $595.0027 Lts 50 Final Drive Oil 35 $0.00 $108.0028 Lts 15/40 Engine Oil 35 $0.00 $104.7245 Lts 15/40 Hyd. Oil 35 $0.00 $168.30130 Lts 30 Trans Oil 35 $0.00 $596.441x 6T5068 Sq. Air (W) 35 $0.00 $8.981x 1R1808 Engine Oil Filter 35 $0.00 $39.561x 326-1644 Fuel Filter 35 $0.00 $41.151x 1R0672 Fuel filter 35 $0.00 $26.081x 328-3655 Trans filter 35 $0.00 $102.412x 1R0777 Hyd. Filter 35 $0.00 $82.211x 612501 Outer Air (W) 35 $0.00 $23.581x 612502 Inner Air (N) 35 $0.00 $56.19

20/06/14 6301.2 Clean, detail, and check over 35 $0.00(Workshop) (Terry S) 3.5 35 $122.50

35 $0.0035 $0.0035 $0.0035 $0.0035 $0.0035 $0.00

TOTALS 554.3 $19,293.75 $26,698.81 $7,064.61MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS20/06/14 6304 Carry out a 250hr service at workshop. 35 $0.00

(Workshop)(Greg S) 3 35 $105.001 x 612501 Outer air filter(W) 35 $0.00 $23.581 x P527595 Cab air filter(W) 35 $0.00 $17.781 x 6T5068 Cab air filter(W) 35 $0.00 $8.9828ltrs 15/40 engine oil 35 $0.00 $101.756ltrs 30w trans oil 35 $0.00 $24.483ltrs 15/40 hydraulic oil 35 $0.00 $11.10

11/07/14 6344.3 Check over for work 35 $0.00Adjust tracks & grease machine, 35 $0.00

Page 13

Repair wires to L/h roof light. 35 $0.00(Workshop) (PB) 2 35 $70.00

20/08/14 Grease and check over machine 35 $0.00(Workshop) (Sam W) 1.5 35 $52.50

21/08/14 63998 Clean machine ready to go out 35 $0.00(Workshop) (Terry S) 2 35 $70.00

22/08/14 Clean, detail, check lights, replace top 35 $0.00cab light sealed beam, replace 2 door 35 $0.00 $11.39wiper blades, perform weed & seed and 35 $0.00 $5.50fire ant docments. (Workshop) (Terry S) 4.5 35 $157.50

22/08/14 Paint under carriage and side arms of 35 $0.00machine ready for hire 35 $0.00 $101.64

(Workshop) (Seb A) 2.5 35 $87.5025/08/14 6404 Travel to Willawong and check UHF radio 35 $0.00

problem, Check A/c not cold, found 35 $0.00heater valve not closing off completely, 35 $0.00turned off heater taps for now, return to 35 $0.00workshop. (Doug O) 2 35 $70.00

29/08/14 6423 Travel to site and replace all wiper blades 35 $0.00 $11.00check over machine and return to w/shop 35 $0.00

(Doug O) 1.75 35 $61.258/09/14 6460 Travel to Willawong and fit G.P.S poles 35 $0.00

to dozer blade, pump up tracks, return to 35 $0.00workshop. (Doug O) 3 35 $105.00

9/09/14 Travel to Willawong Job Site and drop 35 $0.00off oil & grease for operator, return to 35 $0.00workshop. (Doug O) 1.5 35 $52.50

10/09/14 Check over machine. 35 $0.00(Burman Rd Willawong) (Sam W) 0.25 35 $8.75

17/09/14 Top up engine oil (3 Lts 15W/40), stick 35 $0.00 $11.10G.P.S unit to window in cab. (Sam W) 0.5 35 $17.50

19/09/14 Get parts ready for service. 35 $0.00(Workshop) (Doug O) 0.5 35 $17.50

20/09/14 6552 Travel to Willawong for 500 hr service, 35 $0.00Change engine oil & filter 35 $0.00 $38.73 $103.60 " fuel water seperator filter 35 $0.00 $41.89 " secondary fuel filter 35 $0.00 $25.91 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $47.38 " hydraulic oil filters 35 $0.00 $87.74Check over, return from Willawong Job 35 $0.00Site. (Doug O) 3.5 35 $122.50

22/09/14 Complete service paperwork and clean 35 $0.00service truck (Doug O) 0.5 35 $17.50

26/09/14 Look for rubbed wires for A/c fan, found 35 $0.00and repaired, return to workshop from 35 $0.00Willawong. (Sam W) 2 35 $70.00

TOTALS 585.3 $20,378.75 $27,143.91 $7,316.64MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS23/10/14 6697 Travel to Riverstone Crossing and 35 $0.00

inspect for noise in tracks/idlers/rollers, 35 $0.00return home. (Doug O) 1.5 35 $52.50

28/10/14 Change outer engine air filter 35 $0.00 $23.58(Hope Island) (Michael Gilmore) 0.25 35 $8.75

28/10/14 Travel to Hope Island Job Site and 35 $0.00ispect slow/shudder in blade lift and lower 35 $0.00found large rock impeeding movement of 35 $0.00blade lift arm, rock was jammed between 35 $0.00side arm and track frame, remove rock, 35 $0.00inspect air filter light stays on, check air 35 $0.00

Page 14

filter cyclone and sender wiring, found no 35 $0.00problem, light was off at the time of 35 $0.00checking, inspect transmission light 35 $0.00flickers, remove and inspect trans filter, 35 $0.00Fit new transmission filter 35 $0.00 $101.71Check sender and wiring 35 $0.00

(Doug O) 3.5 35 $122.508/11/14 6769.4 Travel to Dixon Drive Pimpama from 35 $0.00

Royston Cresant Reedy Creek and 35 $0.00Change engine oil & filter 35 $0.00 $38.73 $108.08 " primary fuel filter 35 $0.00 $41.89 " secondary fuel filter 35 $0.00 $25.91 " outer air filter (Washed) 35 $0.00 $23.58 " both cab air filters (Washed) 35 $0.00 $26.76Fit new blade cutting edges and end bits 35 $0.00 $723.80with new bolts, nuts and flat washers. 35 $0.00 $52.92Return to workshop. (Doug O) 6.75 35 $236.25

27/11/14 Travel to Dixon Drive Pimpama and 35 $0.00replace 2x ripper boots, pins & retainers. 35 $0.00 $165.00

(Kurtis A) 1 35 $35.002/12/14 Operator Kerry Oates fitted new outer 35 $0.00 $62.35

engine air filter on Job Site at Dixon Drive 35 $0.00Pimpama. 35 $0.00

2/12/14 6926 Travel to Dixon Drive Pimpama and 35 $0.00repair UHF fuse holder wire, return to 35 $0.00workshop. (Greg S) 2 35 $70.00

9/12/14 6972 Load service gear travel to Pimpama, 35 $0.00Change engine oil & filter 35 $0.00 $38.73 $108.08 " primary fuel filter 35 $0.00 $41.89 " secondary fuel filter 35 $0.00 $25.91 " outer air filter (Washed) 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76 " trans oil & filter 35 $0.00 $101.71 $627.52 " hydraulic filters 35 $0.00 $87.74 " L/h side final drive oil, (Dirty oil) 35 $0.00 $57.24Wash trans breather filter, 35 $0.00Check over, return to workshop. (Greg S) 5.5 35 $192.50

11/12/14 Attempt to straighten old GPS pole 35 $0.00(Workshop) (Kurtis A) 2 35 $70.00

17/12/14 Travel to Pimpama and remove blown 35 $0.00hydraulic hose under under ripper control 35 $0.00lever, travel back to workshop. (Ron A) 3 35 $105.00

18/12/14 Take blown hydraulic hose to Enzed 35 $0.00Yatala for replacement, travel to dozer at 35 $0.00Pimpama & fit hose to ripper control valve, 35 $0.00Top up hyd oil (10 Lts 15W/40). (Ron A) 2.5 35 $87.50 $38.60

TOTALS 613.3 $21,358.75 $28,776.46 $8,256.16MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS22/01/15 7140 Travel to Foxwell Rd & adjust both tracks 35 $0.00

Try to grease ripper box top left hand 35 $0.00front bush, remove grease nipple & clean 35 $0.00hole out, bush has turned & will not take 35 $0.00grease.Drop off 20ltrs of Delo 400 to 35 $0.00 $77.20operator Kerry Oates. Return to base. 35 $0.00

(Ron A) 2.5 35 $87.5029/01/15 7172 Travel to Foxwell Road Job Site, repair 35 $0.00

battery post and replace battery jumper 35 $0.00cable. (Doug O) 1.75 35 $61.25

4/02/15 7208 Drive to Foxwell Rd site and repair GPS 35 $0.00fault. Clean and check all connector pins 35 $0.00

Page 15

and sockets.Return to shop (Doug O) 2 35 $70.0011/02/15 7272 Travel to Foxwell Rd Coomera and 35 $0.00

Change outer engine air filter (Washed) 35 $0.00 $23.58Return to workshop. (Greg S) 0.75 35 $26.25

12/02/15 Travel to Foxwell Rd Coomera and 35 $0.00Fit new inner air filter. (New P532502) 35 $0.00 $48.73Fit new outer air filter. (New P532501) 35 $0.00 $58.89Travel to workshop. (Seb A) 1 35 $35.00

14/02/15 7292 Pick up service truck and service gear, 35 $0.00travel to Foxwell Road Job Site, Coomera 35 $0.00Change engine oil & filter 35 $0.00 $38.69 $108.08 " primary fuel filter 35 $0.00 $41.80 " secondary fuel filter 35 $0.00 $26.20 " cab filters (Washed ones) 35 $0.00 $26.76Check over remove floor to inspect oil 35 $0.00leak, replace oring at pump case drain 35 $0.00fitting and test, after repair (OK), 35 $0.00travel to worshop, unload service gear, 35 $0.00dispose of old filters & clean drain trays. 35 $0.00

(Doug O) 4 35 $140.0018/02/14 7314 Travel to Job Site, inspect G.P.S 35 $0.00

problem with left pod, disconnect & clean 35 $0.00all connections behind front grill, under 35 $0.00bonnet & floor, re-connect and test, (OK) 35 $0.00Replace 4 grease nipples on ripper frame, 35 $0.00 $2.80Remove pin not taking grease on ripper 35 $0.00frame tilt brace & found dirt blocking 35 $0.00grease holes, remove brace arm, return 35 $0.00to workshop, press out bush, clean out 35 $0.00dirt & refit bush, return to Job Site and 35 $0.00refit brace arm, Inspect equalizer bar and 35 $0.00found centre pin as well as R/h outer pin 35 $0.00worn out, remove belly guards and 35 $0.00equalizer bar, return to workshop and 35 $0.00clean parts. (Doug O) 8.5 35 $297.50

18/02/15 Travel to Foxwell Rd Coomera to remove 35 $0.00equalizer bar, bring back to workshop 35 $0.00and dismantle. (Kurtis A) 2.5 35 $87.50

18/02/15 Travel to Foxwell Rd Coomera and 35 $0.00remove equalizer bar return to workshop 35 $0.00remove old bushings & seals, clean out 35 $0.00grease holes & clean parts. (Greg S) 3.5 35 $122.50

18/02/15 Start to clean up equalizer bar. 35 $0.00(Workshop) (Mitch C) 1 35 $35.00

35 $0.00TOTALS 640.8 $22,321.25 $29,043.91 $8,441.44

MACHDATE HRS DESCRIPTION LAB RATE COST PARTS OILS18/02/15 7314 Travel to Foxwell Rd Coomera and help 35 $0.00

remove equalizer bar return to workshop. 35 $0.00(Ron A) 1.5 35 $52.50

19/02/15 Clean equalizer bar parts. 35 $0.00(Workshop) (Doug O) 0.5 35 $17.50

19/02/15 Bore & weld up worn outer bearing holes 35 $0.00in equalizer bar and re-assemble bar 35 $0.00with new bearings, rings & seals etc. 35 $0.00 $755.75

(Workshop) (Kurtis A) 7.5 35 $262.5023/02/15 Load up & travel to Foxwell Road and 35 $0.00

refit equalizer bar with new pins, refit 35 $0.00belly plates, return to workshop. 35 $0.00

(Kurtis A) 3 35 $105.00

Page 16

3/03/15 7315 Check over dozer for work, 35 $0.00Top up engine oil (1 Lt 15W/40) 35 $0.00 $3.86Check trans, hydraulic & coolant fluid 35 $0.00levels, Fill washer bottle, 35 $0.00Clean engine breather, 35 $0.00Blow out engine outer air filter 35 $0.00 " " cab A/c air filters, 35 $0.00Clean out A/c evaporator, 35 $0.00Tighten fan and A/c belts 35 $0.00Check lights, replace front light lens assy 35 $0.00 $52.84and fit new globe, Removing exhaust 35 $0.00manifold. (Workshop) (Greg S) 5 35 $175.00

3/03/15 7315 Check over dozer, 35 $0.00Replace 4 leaking bung orings on engine 35 $0.00 $6.48oil filter mounting head, Replace headlight 35 $0.00lens and globe, start to remove exhaust 35 $0.00manifold. (Workshop) (Mitch C) 4.5 35 $157.50

4/03/15 Remove exhaust manifold & removing 35 $0.00broken studs. (Workshop) (Ron A) 5.5 35 $192.50

4/03/15 Clean up exhaust manifold, clean dirt from 35 $0.00around sprocket segments, remove worn 35 $0.00segments, clean mounting surfaces and 35 $0.00fit good S/h ones. (Workshop) (Mitch C) 7.5 35 $262.50

4/03/15 7315 Check oil level in track frame pivots, 35 $0.00clean up exhaust manifold parts & 35 $0.00removing studs, fitting second hand 35 $0.00sprocket segments. (Workshop) (Greg S) 3 35 $105.00

5/03/15 7315 Remove broken manifold studs, tap out 35 $0.00front bottom stud hole to 12mm for 35 $0.00cap screw, fit new studs for exhaust 35 $0.00 $147.98manifold, fit manifold with new gaskets, 35 $0.00 $25.67nuts & flat washers etc, Fit new length of 35 $0.00 $70.91hose for engine precleaner to exhaust, 35 $0.00 $28.51re-assemble and test. 35 $0.00

(Workshop) (Ron A) 7.5 35 $262.505/03/15 7315 Remove broken bolts from engine side 35 $0.00

guards mounting, help refit muffler after 35 $0.00exhaust manifold repairs, remove 35 $0.00sprocket segments and repalce with 35 $0.00good S/h ones, re-check tension of 35 $0.00segment bolts etc. (Workshop) (Mitch C) 6.25 35 $218.75

5/03/15 7315 Fit good S/h sprocket segments. 35 $0.00(Workshop) (Greg S) 2.5 35 $87.50

35 $0.00TOTALS 695 $24,220.00 $30,132.05 $8,445.30

MACHDATE HRS DESCRIPTION LAB RATE COST PARTS OILS6/03/15 Pick up 12mm steel plate from One Steel 35 $0.00

at Yatala, bring back to workshop, pick 35 $0.00template and deliver steel plate & 35 $0.00template to Bendworx to be pressed into 35 $0.00shape of blade skin. (Terry S) 2.75 35 $96.25

6/03/15 Fit 1 new sprocket segment. 35 $0.00 $127.07(Workshop) (Ron A) 1 35 $35.00

6/03/15 7315 Fit new bolts & nuts to good S/h sprocket 35 $0.00 $16.38segments, fit new segment & tighten 35 $0.00bolts etc. (Workshop) (Greg S) 0.5 35 $17.50

35 $0.0010/03/15 Travel to Bendworx and pick up rolled 35 $0.00

blade skin steel, travel to workshop. 35 $0.00(Seb A) 1 35 $35.00

Page 17

11/03/15 Check and adjust tracks. 35 $0.00(Workshop) (Greg S) 0.5 35 $17.50

12/03/15 Gouge off old cutting edge and hardfacing 35 $0.00 $32.19from blade skin, cut & fitting new middle 35 $0.00section of new blade skin steel plate, 35 $0.00 $968.00rolled to shape by Bendworx.(Inv 44207) 35 $0.00 $181.50

(Workshop) (Kurtis A) 4 35 $140.0013/03/15 Cut and fit new side sections of blade 35 $0.00

skin and weld to blade, weld on main 35 $0.00section of skin etc. (Workshop) (Kurtis A) 7.5 35 $262.50

16/03/15 Remove blade cutting edges and finish 35 $0.00welding skin to front of blade, refit 35 $0.00 $32.59cutting edges with new plow bolts, nuts & 35 $0.00 $63.84flat washers. (Workshop) (Kurtis A) 3 35 $105.00

17/03/15 Weld on wear bars to front of blade and 35 $0.00hardface blade, Gouge out cracks in 35 $0.00 $65.98track frames and weld up. 35 $0.00 $9.99

(Workshop) (Kurtis A) 6 35 $210.0024/03/15 7315.8 Check over & grease machine, 35 $0.00

Fill out inspection form. 35 $0.00(Workshop) (Peter B) 1 35 $35.00

24/03/15 Clean dozer. (Workshop) (Terry S) 1.25 35 $43.7525/03/15 Detail machine. (Workshop) (Terry S) 0.75 35 $26.2525/03/15 Check fitment of G.P.S aerial, wrong 35 $0.00

plug, prepare and paint bare spots etc. 35 $0.00(Workshop) (Seb A) 4 35 $140.00

30/03/15 7318.1 Travel to Reedy Creek and diagnose 35 $0.00A/c problem, bypass low pressure switch, 35 $0.00return to workshop. (Seb A) 3 35 $105.00

10/04/15 Travel to Reedy Creek to sort out dozer 35 $0.00not starting. (Seb A) 2 35 $70.00

14/04/15 7361 Travel to Reedy Creek, remove L/h 35 $0.00engine side covers, door & belly guard for 35 $0.00access to starter motor, remove & 35 $0.00replace starter, start up and check, 35 $0.00 $764.50refit covers and belly guards, return travel 35 $0.00to workshop. (Doug O 5) (Seb A 4) 9 35 $315.00

24/04/15 Cut and make up 50mm spacer plates 35 $0.00 $66.44for top rollers and fit to machine with 35 $0.00longer bolts & washers etc. 35 $0.00 $27.21

(Workshop) (Kurtis A) 4.5 35 $157.5035 $0.0035 $0.00

TOTALS 746.8 $26,031.25 $32,487.74 $8,445.30MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS27/04/15 7400 Perform pre-hire check, check oils, 35 $0.00

Clean outer engine air filter 35 $0.00 " cab air filters 35 $0.00Grease machine. (Workshop) (Ron A) 1.5 35 $52.50

27/04/15 7400.3 Clean, detail and check over machine. 35 $0.00(Workshop) (Terry S) 3.75 35 $131.25

21/05/15 7505 Change engine oil & filter 35 $0.00 $38.69 $108.08 " primary fuel filter 35 $0.00 $41.80 " secondary fuel filter 35 $0.00 $26.20 " outer air filter 35 $0.00 $23.58 " cab air filters 35 $0.00 $26.76 " hydraulic filters 35 $0.00 $88.11Check over for work 35 $0.00Removing track plates & sprocket 35 $0.00segments. (Workshop) (Greg S) 6 35 $210.00

Page 18

21/05/15 Sorting out track chain issue, 35 $0.00Change cab filter 35 $0.00Remove track plates, track chains & 35 $0.00sprocket segments. (Workshop) (Peter B) 4 35 $140.00

21/05/15 7505 Peform pre-hire check & service on 35 $0.00machine, Remove track gear. 35 $0.00

(Workshop) (Ron A) 4 35 $140.0021/05/15 Prepare filters for 500 hr service, 35 $0.00

Release pressure from track idlers, 35 $0.00Clean dirt off top roller mounting brackets, 35 $0.00Remove 3 broken bolts from grill. 35 $0.00

(Workshop) (Mitch C) 2 35 $70.0022/05/15 Repair grille, Fit new sprocket segments 35 $0.00 $2.20

Remove old track guides and fit 35 $0.00Peachey made ones with new bolts, 35 $0.00 $11.00Fit new track chains & re-lugged plates, 35 $0.00 $7,040.00adjust tracks & park dozer ready to go. 35 $0.00

(Workshop) (Peter B) 9 35 $315.0022/05/15 7505 Fit new sprocket segments & track 35 $0.00 $607.20

chains, fit re-lugged track plates, clean 35 $0.00up and prepare parts, grease bolts etc. 35 $0.00

(Workshop) (Greg S) 7 35 $245.0022/05/15 7505 Replace tracks and sprocket segments. 35 $0.00

(Workshop) (Ron A) 6 35 $210.0022/05/15 Help bolt up track plates. 35 $0.00

(Workshop) (Seb A) 0.5 35 $17.5028/05/15 Clean machine. (Workshop) (Terry S) 3.25 35 $113.7519/06/15 Travel to Arterial Road Springfield and 35 $0.00

check out A/con on dozer. (Ron A) 0.5 35 $17.5020/06/15 Travel to to Springfield and turn off 35 $0.00

heater taps for cab and check A/c is 35 $0.00working. (Doug O) 0.75 35 $26.25

10/07/15 Travel to Swan Road Pimpama,fit 2 new 35 $0.00ripper boots.10 litre hyd oil (Seb A) 1 35 $35.00 $150.00 $38.50

22/07/15 7748 Travelled to Pimpama for 250 hr service, 35 $0.00Changed engine only, 35 $0.00 $108.08 " outer air filter, 35 $0.00 $23.58 " cab air filters, 35 $0.00 $26.76Fitted GPS antenna, 35 $0.00Checed over, travelled back to workshop, 35 $0.00performed paper work, unloaded and 35 $0.00cleaned up service gear. (Greg S) 3 35 $105.00

TOTALS 799 $27,860.00 $40,593.62 $8,699.96MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS6/08/15 Organise blade corner tips ready for 35 $0.00

replacement. (Workshop) (Seb A) 0.5 35 $17.507/08/15 Loaded stand into ute, travelled to Swan 35 $0.00

Road Pimpama, clean away mud from 35 $0.00nuts, remove blade cutting edges, clean 35 $0.00down blade & cutting edges, turn cutting 35 $0.00edge and fit new end bits with all new 35 $0.00 $266.20plow bolts, nuts & flat washers, 35 $0.00travelled to workshop and unload. (Seb A) 1.5 35 $52.50

12/08/15 Topped up engine oil (10 Lts 15W/40). 35 $0.00 $38.60(Swan Rd Pimpama) (Greg S) 0.25 35 $8.75

1/09/15 7940 Performed 2000 hr service on truck, 35 $0.00Changed engine oil & filter 35 $0.00 $38.69 $141.37 " primary fuel filter 35 $0.00 $51.18 " secondary fuel filter 35 $0.00 $38.04 " inner air filter 35 $0.00 $43.26

Page 19

" outer air filter 35 $0.00 $23.58 " both cab air filters 35 $0.00 $26.76 " transmission oil & filter 35 $0.00 $102.17 $627.52 " hydraulic oil & filters 35 $0.00 $88.11 $182.58 " L/h side fianl drive oil, 35 $0.00 $57.24Started to remove R/h side final drive 35 $0.00from machine. (Workshop) (Greg S) 5.5 35 $192.50

1/09/15 Helped perform 2000 hour service on 35 $0.00dozer, drained transmission and re-filled 35 $0.00with new oil, changed trans oil filters, 35 $0.00drained hydraulic tank oil and refilled with 35 $0.00new oil, changed hyd filters. 35 $0.00

(Workshop) (Ron A) 2.5 35 $87.501/09/15 7940 Assisted with 2000 hr service, split 35 $0.00

R/h side track ready for final drive 35 $0.00assembly removal. (Workshop) (Mitch C) 3.5 35 $122.50

1/09/15 7940 Checked over machine, 35 $0.00Replaced broken positive battery terminal 35 $0.00and fitted new lug terminal to cable, 35 $0.00Removed & straightened blade tilt 35 $0.00cylinder guard, drilled out broken bolts 35 $0.00and re-fitted guard, 35 $0.00Started to remove R/h side final drive 35 $0.00hub assembly. (Workshop) (Doug O) 8.5 35 $297.50

2/09/15 Removed and dismantled R/h side final 35 $0.00drive assembly, cleaned and checked 35 $0.00parts, fitted new ripper boot, pin and 35 $0.00 $82.50retainer. 35 $0.00

(Workshop) (Greg S 8.5) (Mitch C 7.5) 16 35 $560.003/09/15 Pick up R/h final drive parts from 35 $0.00

Hastings Deering & Statewide Bearings. 35 $0.00(Terry S) 2 35 $70.00

3/09/15 Assembled R/h final drive with new 35 $0.00spindle & planet bearings, fitted new 35 $0.00 $593.65lip seal for axle shaft, new duo-cone seal, 35 $0.00 $228.51new planet carrier oring seal, new 35 $0.00 $16.14hub mounting oring & axle cover oring, 35 $0.00 $20.92Filled final drive with new oil (14 lts 50), 35 $0.00 $59.36Joined and adjusted track. 35 $0.00

(Workshop) (Greg S) 5.5 35 $192.5035 $0.00

TOTALS 844.8 $29,461.25 $42,270.57 $9,749.39MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS3/09/15 7940 Repaired L/h light on top of cab, 35 $0.00

Assembled and fitted R/h final drive, 35 $0.00refitted track and parked machine in 35 $0.00wash bay and cleaned. 35 $0.00

(Workshop) (Mitch C) 6.5 35 $227.504/09/15 7940.7 Cleaned machine. (Workshop) (Terry S) 6 35 $210.0011/09/15 Travelled to Robina and checked out 35 $0.00

transmission light staying on, travelled 35 $0.00to workshop. (Doug O). 1.75 35 $61.25

29/09/15 8075 Travelled to Laver Road Robina and 35 $0.00fitted retaining bolt to ripper mounting pin 35 $0.00 $1.75and R clip to engine side cover catch, 35 $0.00travelled to workshop. (Ron A) 1.5 35 $52.50

9/10/15 Travelled to Exit 54 M1, have Seymour/ 35 $0.00White job site induction, 35 $0.00Changed inner air filter (New) 35 $0.00 $48.73 " outer air filter (Washed) 35 $0.00 $24.29

Page 20

Travelled to workshop. (Ron A) 1.5 35 $52.5017/10/15 Travelled to Exit 54 M1 motorway and 35 $0.00

assisted Peter from Red Devil Radiators 35 $0.00with A/c repairs, travelled to workshop. 35 $0.00

(Doug O) 3.5 35 $122.5017/10/15 Red Devil Radiators travelled to Exit 54 35 $0.00

on M1 Motorway, serviced A/c system 35 $0.00repaired faulty wiring and fitted new 35 $0.00thermostat. (Invoice # 42218) 35 $0.00 $510.00

3/11/15 Hastings Deering fitter travelled to 35 $0.00Exit 54 M1 Motorway Coomera, had Site 35 $0.00Induction, located dozer, connected ET 35 $0.00found 48 logged codes for throttle 35 $0.00position sensor, Erratic and incorrect, 35 $0.00could not get fault to occur, Removed 35 $0.00console panel, disconnected throttle 35 $0.00switch, fault code occurred, inspected 35 $0.00switch, mechanism seemed to be loose 35 $0.00& worn, Ordered part, return travel to 35 $0.00collect, Installed new switch, assembled 35 $0.00 $34.24console and tested operation (OK) 35 $0.00(Dozer has active fault code 585-2 for 35 $0.00transmission out put speed sensor # 1 35 $0.00erratic, intermittent, customer is aware 35 $0.00of the fault but but does not want to 35 $0.00repair). (Invoice #AS000151729) 35 $0.00 $470.62

11/11/15 8205 Loaded service gear, travelled to Exit 54 35 $0.00M1 Motorway Coomera for 250 hr service 35 $0.00Changed engine oil only, 35 $0.00 $101.92 " outer air filter, (New P532501) 35 $0.00 $23.58 " cab air filters, (Washed ones) 35 $0.00 $27.63Checked over machine, 35 $0.00Topped up hydraulic oil (2 lts 15W/40), 35 $0.00 $7.28Travelled to the workshop. (Greg S) 3 35 $105.00

17/11/15 Delivered fire extinguisher to dozer on 35 $0.00Job Site at Deebing Heights. (Terry S) 1.75 35 $61.25

30/11/15 Enzed Coopers Plains Hose Van 35 $0.00travelled to Beaufortia Street Deebing 35 $0.00Heights and replaced 2x hydraulic hoses 35 $0.00as required. (Invoice No 4849165 R1) 35 $0.00 $1,128.64

TOTALS 870.3 $30,353.75 $44,540.05 $9,858.59MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS11/12/15 Travelled to Robina and checked out 35 $0.00

A/c system not working, found 35 $0.00compressor clutch activating wire rubbed 35 $0.00through and shorting out, repaired wire 35 $0.00and travelled back to the workshop. 35 $0.00

(Ron A) 1.5 35 $52.5015/12/15 Enzed Coopers Plains Hose Van 35 $0.00

travelled to Pensar Job Site Beauforth 35 $0.00Street Deebing Heights and replaced 35 $0.00blade tilt hydraulic hose assembly. 35 $0.00(Invoice No 4858225 RI) 35 $0.00 $313.42

21/01/16 8498 Loaded service gear, travelled to Robina 35 $0.00for 500 hour service 35 $0.00Changed engine oil and filter 35 $0.00 $38.69 $101.92 " primary fuel filter 35 $0.00 $51.18 " secondary fuel filter 35 $0.00 $26.20 " outer air filter 35 $0.00 $24.29 " both cab air filters 35 $0.00 $27.63

Page 21

" hydraulic oil filters 35 $0.00 $88.11Topped up hydraulic oil (3 lts 15W/40), 35 $0.00 $10.92Checked over, returned to the workshop, 35 $0.00unloaded and fitted out service sheet. 35 $0.00

(Mitch C 4) (Doug O 4) 8 35 $280.0011/02/16 8572.2 Cleaned machine. (Workshop) (Terry S) 1 35 $35.0012/02/16 8572.2 Carry out a pre-hire inspection sheet on 35 $0.00

machine in workshop. Top up Engine & 35 $0.00Hydraulic oil levels. 35 $0.0010ltrs x 15W/40 Engine Oil 35 $0.00 $36.4010ltrs x 15W/40 Hydraulic Oil 35 $0.00 $36.40(Workshop)(Greg S-1hr) & (Peter B-1.5hr) 2.5 35 $87.50

12/02/16 Cleaned, detailed and carried checks 35 $0.00on machine. 35 $0.00(Workshop) (Terry S) 3 35 $105.00

16/02/16 8575 Travel to site at Reedy Creek to repair 35 $0.00A/C condensor, drill out old rivots and 35 $0.00replace with new ones. (Seb A) 2 35 $70.00

26/02/16 Carried out checks on machine and 35 $0.00fueled up 35 $0.00

(Workshop)(TerryS) 1 35 $35.0026/02/16 Remove & replace all 3 ripper boots on 35 $0.00

ripper tynes on rear of dozer. 35 $0.00 $247.50(Workshop)(Seb A) 0.5 35 $17.50

7/03/16 Travelled to Heathwood and inspected 35 $0.00noisy belt pulley, Removed fan belt 35 $0.00adjuster pulley & bracket assembly, 35 $0.00dismantled pulley, travelled to Hastings 35 $0.00and picked up parts, returned to Job Site 35 $0.00re-assembled pulley to new bracket with 35 $0.00 $257.15new bearings, seals and cap, fitted pulley 35 $0.00 $70.26assembly to machine, started and 35 $0.00checked, travelled home. (Doug O) 4.5 35 $157.50

18/03/16 8731 Washed dozer and checked over, 35 $0.00Topped up engine oil, (2 Lts 15W/40). 35 $0.00 $7.28 " " transmission, oil (5 lts 30) 35 $0.00 $8.48 " " hydraulic oil, (5 lts 15W/40). 35 $0.00 $18.20

(Workshop) (Mitch C) 2 35 $70.0035 $0.00

TOTALS 896.3 $31,263.75 $45,684.48 $10,078.19MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS22/03/16 8741 Loaded up travelled to Coomera Waters, 35 $0.00

Changed primary fuel filter 35 $0.00 $41.80 " secondary fuel filter, 35 $0.00 $26.19Obtained machine fault codes, 35 $0.00travelled back to the workshop, checked 35 $0.00codes in manual, travelled back to the 35 $0.00machine, 35 $0.00Changed engine inner air filter (P532502) 35 $0.00 $49.53 " engine outer air filter (P532501) 35 $0.00 $60.32Re-checked machine faults and 35 $0.00returned to the workshop. (Greg S) 6.5 35 $227.50

22/03/16 All Diesels Travelled to Coomera Waters 35 $0.00checked through fault codes that may 35 $0.00cause loss of power, could not find any, 35 $0.00Ran diagnostic test an engine, all 35 $0.00checked okay, suspect faulty sensor 35 $0.00inside transmission. 35 $0.00(All Diesels Invoice # Q18256) 35 $0.00 $390.50

23/03/16 8744 Removed trans gaurds from rear and 35 $0.00

Page 22

under machine, cleaned under machine, 35 $0.00removed rear trans cover & checked 35 $0.00speed sensors, (OK), Checked wiring 35 $0.00loom to ECM, found wire 900 to be 35 $0.00opened circuited, Replaced wire ECM to 35 $0.00 $0.45trans plug, Had to remove seat, floor 35 $0.00plate, seat base mount plate and side 35 $0.00covers to do so, Tested machine, 35 $0.00Re-fitted covers, seat base mount plate, 35 $0.00floor plate and seat, loaded onto the 35 $0.00float ready to return to the Job Site at 35 $0.00Coomera Waters. (Workshop) (Peter B) 8.5 35 $297.50(Wire 901 to speed sensor # 1 has 35 $0.00already been replaced, Wire 900 is for 35 $0.00Sensor # 1 also). 35 $0.00

23/03/16 Carried out investigation for de-rated fault, 35 $0.00Removed transmission back cover to 35 $0.00access speed sensors, Removed 35 $0.00leaking transmission hose assembly 35 $0.00and fitted new hose supplied by Enzed 35 $0.00Yatala, (Invoice # GCN 104498) 35 $0.00 $325.03Fitted new mounting split clamp to new 35 $0.00 $11.18trans hose. (Workshop) (Steve C) 6.5 35 $227.50

23/03/16 8744 Performed 250 hour service on dozer, 35 $0.00Changed engine oil, (28 lts 15W/40) 35 $0.00 $101.92 " " " filter (1R1808) 35 $0.00 $38.69 " long cab air filter, (W, 6T0988) 35 $0.00 $18.30 " square cab air filter (W 6T5068) 35 $0.00 $9.33Topped up hydraulic oil (1 lts 15W/40) 35 $0.00 $3.64Greased truck, 35 $0.00Prepared for work, Re-fitted guards, 35 $0.00checked over for work. 35 $0.00

(Workshop) (Greg S ) 3 35 $105.0023/03/16 Travelled to Enzed Yatala to deliver 35 $0.00

leaking transmission hose to use as a 35 $0.00sample for a replacemnt hose, travelled 35 $0.00back to the workshop. (Mitch C) 0.5 35 $17.50

35 $0.00TOTALS 921.3 $32,138.75 $46,655.80 $10,183.75

MACHDATE HRS DESCRIPTION LAB RATE COST PARTS OILS29/03/16 Travelled to Coomera Waters to check 35 $0.00

de-rating faults, read the codes and 35 $0.00checked for anything rubbed through in 35 $0.00engine bay, found waste gate hose to be 35 $0.00rubbed through, found fuel pressure to 35 $0.00be dropping off and de-rating, checked 35 $0.005 volt feed from ECM all OK, (Fuel lines 35 $0.00need replacing, rubbed through may be 35 $0.00causing air to be drawn into the fuel 35 $0.00system, travelled to the workshop. 35 $0.00

(Steve C) 5 35 $175.0029/03/16 Checking faults and possible cause of 35 $0.00

engine de-rating. (Workshop) (Peter B) 1 35 $35.0030/03/16 Meet up with Rob from All Diesels at 35 $0.00

Coomera Waters to check fuel pressure, 35 $0.00cleaned out fuel lines which need 35 $0.00replacing next time machine is at the 35 $0.00workshop, travelled to the workshop. 35 $0.00

(Steve C) 3.5 35 $122.5030/03/16 All Diesels Travelled to Coomera Waters 35 $0.00

Page 23

checked through engine and found low 35 $0.00fuel pressure checked wiring and sensor 35 $0.00all check okay checked fuel system 35 $0.00and found rust in fuel supply line 35 $0.00(Invoice Q18271) 35 $0.00 $291.50

35 $0.004/04/16 8879.2 Travelled to Coomera Waters, checked 35 $0.00

fuel lines and fuel level, found a lot of 35 $0.00rust and dirt in fuel filter bowl. (Steve C) 1.5 35 $52.50

6/04/16 8813 Travelled to Coomera Waters and 35 $0.00replaced track plate bolts, travelled to 35 $0.00 $10.36the workshop. (Steve C) 3.5 35 $122.50

21/04/16 Removed fuel lines to replaced. 35 $0.00(Workshop) (Steve C) 1 35 $35.00

22/04/16 Removed engine side covers and cab 35 $0.00floor plates to gain access to the fuel 35 $0.00lines removed all fuel lines, travelled to 35 $0.00Enzed Yatala Store for replacement ones 35 $0.00(Enzed Yatala Invoice # GCN 104892) 35 $0.00 $359.14fitted new fuel lines and re-fitted side 35 $0.00panels and cab floor plates, Carried out 35 $0.00machine check over for defects. 35 $0.00

(Workshop) (Steve C) 6.5 35 $227.5022/04/16 Removed old and fitted new set of 35 $0.00

Cutting Edges and End Bits to the blade 35 $0.00 $639.48with new plow bolts & nuts. 35 $0.00 $53.76

(Workshop) (Seb A) 1.5 35 $52.5026/04/16 8857 Cleaned, washed and detailed. 35 $0.00

(Workshop) (Jordan L) 4 35 $140.005/05/16 Checked over machine & fuel up. 35 $0.00

(Workshop) (Seb A) 1 35 $35.0035 $0.00

NEXT PAGE 35 $0.0035 $0.0035 $0.0035 $0.00

TOTALS 955.3 $33,328.75 $48,010.04 $10,183.75MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS6/05/16 Travelled to Pimpama and checked 35 $0.00

wiring for to GPS unit, removed floor 35 $0.00plates to gain access, checked for power, 35 $0.00called Sitec found to be fault in power 35 $0.00module, requires new one, (Dean to 35 $0.00service). (Steve C) 3.5 35 $122.50

9/05/16 Travelled to Pimpama and investigated 35 $0.00GPS issues, started to change out 35 $0.00harness, but found it had rubbed through 35 $0.00wires was old, light bars on front control 35 $0.00panel, disconnected and tested, 35 $0.00travelled to the wokshop. (Steve C) 3 35 $105.00

10/05/16 Loaded up ripper tynes at the workshop, 35 $0.00travelled to Dixon Drive Pimpama to 35 $0.00swap out broken ripper tyne, spare tynes 35 $0.00had different boots & pins, loaded 35 $0.00broken tyne and travelled back to the 35 $0.00workshop, unloaded tyne and ordered 35 $0.00new replacement tyne from R D Williams 35 $0.00Cat Parts. (Seb A) 1.5 35 $52.50

12/05/16 8899 Travelled to Dixon Drive Pimpama, 35 $0.00removed leaking blade tilt hose, took to 35 $0.00

Page 24

Enzed Yatala Store for new hose, 35 $0.00(Enzed Yatala Invoice # GCN 105172), 35 $0.00 $301.02travelled back to the machine & fitted new 35 $0.00hose, Topped up hyd oil (5 lts 15W/40), 35 $0.00 $19.30Dropped off new ripper tyne, re-fitted 35 $0.00 $550.00original boot from broken tyne with new 35 $0.00pin & retainer, travelled to the workshop. 35 $0.00 $5.50

(Greg S) 2.5 35 $87.5016/05/16 8915 Travelled to Dixon Drive Pimpama and 35 $0.00

replaced 3x ripper boots, pins & retainers. 35 $0.00 $178.20(Steve C) 1 35 $35.00

16/05/16 8915 Travelled with Steve to deliver 2x ripper 35 $0.00boots and fitted 1x ripper boot. (Mitch C) 0.75 35 $26.25

18/05/16 8932 Travelled to Dixon Drive Pimpama and 35 $0.00replaced missing grouser plate bolts 35 $0.00 $7.86and tightened up loose ones. (Mitch C) 0.75 35 $26.25

21/05/16 Travelled to Dixon Drive Pimpama and 35 $0.00drove back in R/h ripper box pin into 35 $0.00ripper box frame and welded in place, 35 $0.00travelled home. (Kurtis A) 4 35 $140.00

23/05/16 Travelled to Dixon Drive Pimpama, 35 $0.00drained oil, removed floor plates, side 35 $0.00covers, covers around hyd tank and all 35 $0.00P clamps holding blown hydraulic cooler 35 $0.00hose assembly, removed hose for 35 $0.00Enzed Yatala to supply new hose, 35 $0.00travelled back to the workshop. (Steve C) 6.5 35 $227.50

23/05/16 Travelled to Enzed Yatala and waited 35 $0.00while new hyd cooler hose was made up, 35 $0.00returned to the workshop. (Doug O) 0.5 35 $17.50

23/05/16 Welded up and re-painted light protection 35 $0.00box. (Workshop) (Seb A) 1 35 $35.00

35 $0.0035 $0.0035 $0.00

TOTALS 980.3 $34,203.75 $49,052.62 $10,203.05MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS24/05/16 Travelled to Dixon Drive Pimpama and 35 $0.00

fitted new hydraulic cooler hose assembly 35 $0.00supplied by Enzed Yatala Store, (Invoice 35 $0.00Number GCN 105315), under the floor 35 $0.00 $322.11from the front of the machine to the hyd 35 $0.00tank fastened in place with the P clamps, 35 $0.00filled hydraulic oil (45 lts 15W/40), tested 35 $0.00 $173.70(All OK), travlled to the workshop. 35 $0.00

(Steve C) 2 35 $70.0026/05/16 Travelled to Dixon Drive Pimpama and 35 $0.00

hammered ripper pin into frame and 35 $0.00 $1.75welded in place, replaced 2x 1/8" BSP 35 $0.00straight grease nipples, travelled back to 35 $0.00 $1.40the worskshop. (Kurtis A) 1.5 35 $52.50

27/05/16 Travelled to the machine at Dixon Drive 35 $0.00Pimpama from Swan Road Pimpama, 35 $0.00topped up engine oil (No amount supplied) 35 $0.00Found mounting lugs broken on cover at 35 $0.00R/h side of cab, travelled to the workshop. 35 $0.00

(Doug O) 1 35 $35.001/06/16 9002 Performed 1000 hour service on machine, 35 $0.00

Changed engine oil ( 28 lts 15W/40) 35 $0.00 $109.76 " engine oil filter (1R1808) 35 $0.00 $38.69

Page 25

" primary fuel filter (326-1644) 35 $0.00 $41.80 " secondary fuel filter (1R0762) 35 $0.00 $26.19 " outer air filter (W) (P532501) 35 $0.00 $24.29 " long cab air filter, (W) (6T0988) 35 $0.00 $18.30 " square cab air filter (W 6T5068) 35 $0.00 $9.33 " trans oil, (148 lts 30 grade) 35 $0.00 $559.44 " transmission oil filter (328-3655) 35 $0.00 $102.16 " transmission breather (9G5127) 35 $0.00 $12.77 " hydraulic oil filters (2x 1R0777) 35 $0.00 $88.11Topped up hydraulic oil, (7 lts 15W/40) 35 $0.00 $27.44Checked final drive oils, (Found metal on 35 $0.00magnetic plugs on both sides), 35 $0.00Fitted new bolts to trans rear suction 35 $0.00 $0.60screen cover, Checked over machine. 35 $0.00

(Workshop) (Greg S) 8 35 $280.001/06/16 Removed belly guard, dug out mud to 35 $0.00

access damaged equalizer bar grease 35 $0.00line hose and removed the hose, 35 $0.00removed damaged transmission filter 35 $0.00guard, cleaned up work area. 35 $0.00

(Workshop) (Mitch C) 2.75 35 $96.252/06/16 9002 Fueled up and re-fitted ripper tynes. 35 $0.00

(Workshop) (Greg S) 1 35 $35.002/6/176 Cut and welded plates to blade and 35 $0.00 $211.98

blade side arms. (Workshop) (Kurtis A) 6.5 35 $227.502/06/17 9002 Travelled to Enzed Yatala Store for a 35 $0.00

new equalizer bar grease line hose assy, 35 $0.00(Enzed Yatala Invoice # GCN Y51454) 35 $0.00 $109.49travelled to the workshop and fitted, 35 $0.00cleaned up the work area. (Mitch C) 1.5 35 $52.50

3/06/16 Turned up new pin & bush for tilt ram 35 $0.00 $22.74mounting and installed, Repaired 35 $0.00transmission cover plate and cracks in 35 $0.00R/h running board. (Workshop) (Kurtis A) 6 35 $210.00

TOTALS 1011 $35,262.50 $50,084.33 $11,073.39MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS3/06/16 9002 Re-fitted guards and belly guards. 35 $0.00

(Workshop) (Mitch C) 1 35 $35.006/06/16 Cleaned, washed, de-greased and 35 $0.00

detailed the dozer.(Workshop) (Jordan L) 3.25 35 $113.758/06/16 9004 Prepared machine for injector removal, 35 $0.00

performed injector checking with All 35 $0.00Diesels, checked for faulty injector, 35 $0.00Cleaned A/c evatorator. 35 $0.00

(Workshop) (Greg S) 6 35 $210.008/06/16 All Diesels travelled to the Ormeau 35 $0.00

Workshops, connected dianostic tool, 35 $0.00carried out tests but could not diagnose 35 $0.00which injector was faulty. (Invoice Q18376) 35 $0.00 $253.00

13/06/16 9020 Travelled to Santa Barbara Road 35 $0.00Sanctuary Cove and inspected engine 35 $0.00running rough, blew out the fuel lines 35 $0.00and test run, travelled to the workshop. 35 $0.00

(Doug O) 2 35 $70.0014/06/16 Travelled to Santa Barbara Road 35 $0.00

Sanctuary Cove and trouble shoot 35 $0.00engine running rough under load 35 $0.00intermittanly, Assist Rob from All Diesels 35 $0.00with testing electronic system and found 35 $0.00No 2 injector and throttle position switch 35 $0.00

Page 26

faulty, removed pre-cleaner/air filter 35 $0.00housing, brackets and wiring harness for 35 $0.00access, removed rocker cover and 35 $0.00removed and replaced No 2 injector with 35 $0.00 $803.88reman one, re-fitted all parts, started 35 $0.00and checked engine, travelled back to 35 $0.00the workshop. (Doug O) 8 35 $280.00

14/06/16 All Diesels travelled to Sanctuary Cove 35 $0.00Job Site, tested injectors when cold, 35 $0.00Found injector No 2 to be faulty, Also 35 $0.00found throttle sensor signal erratic, 35 $0.00Peachey fitter Doug O changed No 2 35 $0.00injector and sensor. (Invoice # Q18376) 35 $0.00 $445.50

15/06/16 Travelled to Hastings Deering and 35 $0.00collected parts, travelled to Sanctuary 35 $0.00Cove, replaced throttle position sensor, 35 $0.00 $184.76trouble shoot another fault code 35 $0.00relating to throttle switch in cab, found 35 $0.00rubbed through wire in engine harness 35 $0.00shorting to ground, repaired fault and 35 $0.00tested, waited on site while machine 35 $0.00went to work, (All OK now), travelled to 35 $0.00the workshop. (Doug O) 4.25 35 $148.75

15/06/16 All Diesels travelled back to Sanctuary 35 $0.00Cove and programed trim code and 35 $0.00checked for any further issues, found a 35 $0.00fault with idle switch circuit, traced 35 $0.00through and found a wire shorting out on 35 $0.00a bracket near the back of the rocker 35 $0.00cover, supplied service charge. 35 $0.00service charge. (Invoice # Q18376) 35 $0.00 $286.00

17/06/16 Checked over machine and repaired the 35 $0.00fan shrouds. (Workshop) (Seb A) 1 35 $35.00

TOTALS 1036 $36,155.00 $52,057.47 $11,073.39MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS6/07/16 9124 Removed under guards ready for cleaning. 35 $0.00

(Workshop) (Greg S) 1.5 35 $52.506/07/16 9124 Removed belly guards and moved 35 $0.00

machine into the wash bay. 35 $0.00(Workshop) (Mitch C) 1 35 $35.00

7/07/16 9124.7 Cleaned, washed, degreased & detailed. 35 $0.00(Workshop) (Jordan L) 5.5 35 $192.50

7/07/16 9125 Removed seat for repair and fitted 35 $0.00stickers, refitted guards under machine, 35 $0.00fitted serviced fire extinguisher, 35 $0.00 $94.60Topped up engine oil (.5 lts 15W/40) 35 $0.00 $1.96 " " hydraulic oil (3 lts 15W/40) 35 $0.00 $11.76Prepared machine for work and fueled up. 35 $0.00

(Workshop) (Greg S) 5 35 $175.007/07/16 9125 Removed the seat with Greg S ready 35 $0.00

for repair, Performed machine check over 35 $0.00for Lend Lease Hire check sheet, Fueled 35 $0.00up machine. (Workshop) (Mitch C) 3 35 $105.00

7/07/16 9125 Fitted belly guards, removed Peachey 35 $0.00stickers and checked over the machine. 35 $0.00

(Workshop) (Steve C) 3.5 35 $122.508/07/16 9125 Changed outer air filter (W) (P532501) 35 $0.00 $24.29

Blew out cab A/c air filters 35 $0.00Fitted seals to trans filter housing senor, 35 $0.00 $2.00Fitted 3x new E Stops 35 $0.00 $306.90

Page 27

Grease the machine, 35 $0.00(Workshop) (Greg S) 6.5 35 $227.50

8/07/16 9125 Fitted new E Stops, wired up and tested 35 $0.00 $2.34on machine. (Workshop) (Mitch C) 5 35 $175.00

8/07/16 Service 8 Pty Ltd travelled to the 35 $0.00workshop, cut and fitted new rear window 35 $0.00glass to the cab. (Invoice # 1035) 35 $0.00 $479.00

11/07/16 9125 Finished lend lease check sheet for 35 $0.00machine hire, masked up machine ready 35 $0.00for painting and painted the track frames 35 $0.00fitted safety stickers. 35 $0.00

(Workshop) (Mitch C) 3.5 35 $122.5012/07/16 Removed masking from machine after 35 $0.00

painting, Blew out rocks and dirt from the 35 $0.00transmission guard, cleaned up. 35 $0.00

(Workshop) (Mitch C) 0.75 35 $26.2514/07/16 9125 Fitted seat bum cushion repaired by 35 $0.00

Beenleigh Auto Trimming. Inv10312 35 $0.00 $220.00(Workshop) (Greg S) 0.75 35 $26.25

8/08/16 Carried out machine inspection, checked 35 $0.00over and find and repair fault with the 35 $0.00de-accelarator. (Workshop) (Steve C) 2 35 $70.00

9/08/16 Cleaned, washed and detailed. 35 $0.00(Workshop) (Jordan L) 1.5 35 $52.50

10/08/16 Greased machine and prepared machine 35 $0.00for work. (Workshop) (Greg S) 1 35 $35.00

16/08/16 Purchased cables for repairs to machine. 35 $0.00 $46.1716/08/16 9173 Checked and filled track frame piviot oils, 35 $0.00

cleaned out rocks from rear guard. Fitted 35 $0.00new battery terminal, refit batteries, 35 $0.00fit rubber over batteries. Prepared machine 35 $0.00for work. (Workshop) (Greg S) 3 35 $105.00

TOTALS 1080 $37,677.50 $53,232.77 $11,087.11MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS16/08/16 Installed and wired up starter isolator. 35 $0.00

Installed and wired up jump start 35 $0.00receptacle, removed isolator switches from 35 $0.00 $475.68Unit #136 to place on this machine. 35 $0.00Place stickers on machine with high vis 35 $0.00tape, fit new reverse camera. (Seb A) 9 35 $315.00

16/08/16 Weed and Seed Inspection. 35 $0.00(Workshop) (Jordan L) 0.25 35 $8.75

17/08/16 9173 Fit new seat belt and cleaned out cab. 35 $0.00 $108.00(Workshop) (Seb A) 0.5 35 $17.50

17/08/16 9173.3 Detailed machine. (Workshop) (Jordan L) 0.5 35 $17.5023/08/16 9173 Removed guards for cleaning and checked 35 $0.00

oil leak on trans pump. 35 $0.00(Workshop) (Greg S) (Mitch C) 1.5 35 $52.50

23/08/16 Prep machine ready to remove trans 35 $0.00pump removed belly guards. (Steve C) 2.5 35 $87.50

23/08/16 Cleaned machine. (Workshop) (JordanL) 2.5 35 $87.5024/08/16 9174 Cleaned transmission suction screen and 35 $0.00

magnetics. Removed worn pump drive 35 $0.00couplings, repaired drive shaft valves. 35 $0.00 $66.04Sorted out new drive couplings and fit to 35 $0.00 $524.41shaft. Placed machine in washbay and 35 $0.00washed machine. Placed machine then in 35 $0.00the workshop, repaired oil leak on hyd 35 $0.00pump fitting. Fit floor plates etc. Topped 35 $0.00up fuel. (Workshop) (Peter B) 6.25 35 $218.75

Page 28

24/08/16 Removed guards for cleaning, reseal 35 $0.00trans pump, cleaned dirt off machine and 35 $0.00refitted guards. (Workshop) (Greg S) 6.5 35 $227.50

24/08/16 Removed floor plates, gained access to 35 $0.00the trans pimp removed GPS wiring and 35 $0.00control box. Removed transmission pump 35 $0.00stripped down and replaced all orings 35 $0.00refit and checked levels all ok. 35 $0.00

(Workshop) (Steve C) 4 35 $140.0024/08/16 Assisted with resealing and refitting 35 $0.00

trans pump. Assisted Steve and Greg. 35 $0.00Took photos of machine from under 35 $0.00machine for Weed and Seed records. 35 $0.00Carried out 250 hour service in machine. 35 $0.00Changed engine oil, (28 lts 15W/40) 35 $0.00 $101.92 " " " filter (1R1808) 35 $0.00 $38.69 " long cab air filter, (W, 6T0988) 35 $0.00 $18.30 " square cab air filter (W 6T5068) 35 $0.00 $9.33Topped up hydraulic oil (1 lts 15W/40) 35 $0.00 $3.64

(Workshop) (Mitch C) 7.5 35 $262.5024/08/16 Cleaned, washed and detailed machine. 35 $0.00

(Workshok) (Jordan L) 1.5 35 $52.507/09/16 Westrac - Engine wont rev - cause of 35 $0.00

failure: wiring rubbed through near ECM 35 $0.00resultant damage: active codes for 35 $0.00throttle position and throttle switch. Repair 35 $0.00process comments: trouble shoot active 35 $0.00codes, replaced sensor and switch, codes 35 $0.00still present, removed all guards from LHS 35 $0.00of engine, diassembled dash and trouble 35 $0.00shoot wiring harness, found two different 35 $0.00wires with high resistence, replaced both 35 $0.00wires between the ECM and engine 35 $0.00harness plug. Checked operation, all ok, 35 $0.00reinstalled guards. Inv SI 1228008 35 $0.00 $1,964.00

9/09/16 Westrac repaired hydraulic system - 35 $0.00cause of failure - cracked trunion resultant 35 $0.00damage - excessive monent in trunion, 35 $0.00repair precess comments: loaded parts 35 $0.00travelled to site removed lift cylinder, 35 $0.00removed and replaced blade lift trunion 35 $0.00installed lift cylinder checked operations 35 $0.00tested ok. Invoice SI1228357 $4594.37 35 $0.00 $4,594.37

35 $0.0035 $0.0035 $0.0035 $0.0035 $0.0035 $0.0035 $0.0035 $0.0035 $0.00

TOTALS 1122 $39,165.00 $61,031.59 $11,192.67MACH

DATE HRS DESCRIPTION LAB RATE COST PARTS OILS