Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
DVR-4HD
2nd Generation Vehicle Drive Recorder 2018
DVR-5HD
User manual
ContentsAbout this Guide ...............................................................................4FCC Statement ................................................................................4WEEE Notice ...................................................................................5CE Regulatory Notice ......................................................................5Battery Warning ...............................................................................5Notes on Installation ........................................................................6Caution ............................................................................................71 Introduction 81.1 Features 81.2 Package Contents 81.3 Product Overview 91.3.1 Main Body Graphic 91.3.2 Rear Camera Graphic 102 Getting Started 112.1 Storage Media 112.1.1 Insert the Memory Card 112.1.2 Remove the Memory Card 112.2 Installing in Vehicles 122.2.1 Mount the Device to Windshield 122.2.2 Adjust the Device 132.2.2.1 Dismount the Device 142.2.2.2 Dismount the Bracket 142.2.3 Mount Rear Camera to the Windshield 152.2.4 Adjust Rear Camera 162.2.4.1 Record Rearview 162.2.4.2 Record inside the Vehicle 172.3 Connecting to Power and Rear Camera 182.3.1 Connecting to Power 182.3.2 Connecting to Rear Camera 192.4 LED Indicator 212.5 Powering the Device On / Off 22
1 Introduction ..................................................................... 71.1 Features .............................................................................71.2 Package Contents .............................................................71.3 Product Overview ..............................................................81.4 Product Overview – Rear camera (DVR-5HD only) .............9
2 Getting Started......................................................................102.1 Storage Media .................................................................102.1.1 Inserting the Memory Card ..............................................102.1.2 Removing the Memory Card ............................................102.2 Installation in Vehicles ......................................................112.2.1 Mount to Windshield ........................................................112.2.2 Adjusting the device position ...........................................122.3 Connecting to the Power Supply .....................................132.4 Installation in Vehicles – Rear Camera (DVR-5HD only) ...142.4.1 Mounting Rear Camera to the Windshield ..........................142.4.2 Adjusting Rear Camera (DVR-5HD only) .............................162.4.2.1 Recording Rear View .......................................................162.4.2.2 Recording Inside the Vehicle ............................................172.5 Connect and Set Up Rear Camera (DVR-5HD only) ..........182.5.1 Battery Status Indicator ...................................................192.6 LED Indicator ...................................................................192.7 Powering the Device On / Off and Resetting .......................202.7.1 Auto Power On/Off ...........................................................202.7.2 Manual Power On/Off ......................................................202.7.3 Reset ...............................................................................202.8 Initial Settings ..................................................................212.8.1 Set the Time Zone ............................................................212.8.2 Set the Date / Time ..........................................................23
About this Guide ....................................................................... .......3WEEE Notice ............................................................................ .......4CE Regulatory Notice ............................................................... .......4Battery Warning ........................................................................ .......4Notes on Installation ................................................................. .......5Caution ................................................................................ ............6
1DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2.5.1 Auto Power On/Off 222.5.2 Manual Power On/Off and Reset 222.5.2.1 Manual Power On 222.5.2.2 Manual Power Off 222.5.2.3 Reset the Device 222.6 Initial Settings 232.6.1 Set Time zone 232.6.2 Set the Date / Time 253 Using the Drive Recorder 263.1 Automatic Record 263.1.1 Resolution 263.1.2 The Recording Screen 273.1.3 Emergency Recording 293.2 Add Speed Point 303.3 Picture in Video 303.4 Driving Safety 313.4.1 Speed Limit Alert 323.4.2 Parking Mode 333.4.3 Collision Detection 353.4.4 Driver Fatigue Alert 363.4.5 Headlight Warning 373.4.6 LDWS 383.4.7 FCWS 403.4.8 FCMD 41 3.5 File Playback 423.5.1 Playing Videos 433.5.2 Viewing Pictures 443.5.3 Playback Screen 453.6 Deleting Files 474 Adjusting the Settings 494.1 Using the Menu 494.2 Menu Items 505 Connecting to Other Devices 555.1 Connecting to the Computer 55
3 Using the Drive Recorder..................................................24 3.1 Automatic Recording .......................................................24 3.1.1 The Front Camera’s Recording Screen.............................25 3.1.2 Emergency Recording......................................................27 3.2 Add Speed Point..............................................................28 3.3 Picture in Video ...............................................................28 3.4 Driving Safety ..................................................................29 3.4.1 Speed Cam Alert .............................................................29 3.4.2 Speed Limit Alert .............................................................30 3.5 Parking Mode...................................................................31 3.6 Collision Detection ..........................................................33 3.7 Driver Fatigue Alert ..........................................................34 3.8 LDWS ..............................................................................34 3.9 FCWS ..............................................................................36 3.10 2 Grid Function Chart .....................................................37 3.11 Playback Videos and Photos ..........................................38 3.11.1 Playback ..........................................................................38 3.11.2 Playback Mode ............................................................39 3.12 Deleting Files ...................................................................40
4 Adjusting the Settings .....................................................42 4.1 Using the Menu ..............................................................42 5 Connecting to Other Devices ..........................................45 5.1 Connecting to the Computer............................................45 5.2 Connecting to TV .............................................................46 6 Installing the Software .....................................................47 6.1 Updating the speed camera data.....................................48 7 Snooper DVR Player ........................................................49 8 Specifications...............................................................50 9 Service Under Warranty ................................................52
2DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
About this Guide The content in this document is for information purpose and is subject to change without prior notice. We have made every effort to ensure that this User Guide is accurate and complete. However, no liability is assumed for any errors or omissions that may have occurred. The manufacturer reserves the right to change the technical specifications without prior notice.
IMPORTANT NOTICE:The only regular maintenance required on a Dash Cam is formatting the Micro SD Card. Most problems encountered with Dash Cams are SD card related and not the Dash Cam itself.
For optimal performance of your Dash Cam and the SD card, it is recommended to format your SD Card monthly. It is also important to format your Micro SD card at first use via the camera menu.Due to the fragmented nature of the files produced, from constantly starting and stopping recordings, these partial files will clog up the SD card and may negative impact on recordings quality and the lifespan of the SD card.
It is the responsibility of the user to regularly review footage to check that videos and data is recording correctly.
3DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
WEEE Notice Disposal of Waste Electrical and Electronic Equipment and/or Battery by users in private households in the European Union
This symbol on the product or on the packaging indicates that this cannot be disposed of as a household waste. You must dispose of your waste equipment and/or battery by handling it over to the applicable take-back scheme for the recycling of electrical and electronic equipment and/or battery. For more information about recycling of this equipment and/or battery, please contact your city office, the shop where you purchased the equipment or your household waste disposal service. The recycling of materials will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and environment.
CE Regulatory Notice This product will meet the Basic Restriction limits of 1999/519/EC. The product herewith complies with the requirements of the Low Voltage Directive 2014/35/EU, the EMC Directive 2014/30/EU, battery directive 2006/66/EC, the R&TTE Directive 1999/5/EC and the RoHS Directive 2011/65/EC.
Battery Warning • Never dismantle, crush, or pierce the battery. Do not expose the
battery to a high temperature environment.• Only replace the battery with a genuine Snooper battery.• Keep the battery out of reach of children.• Batteries may explode if exposed to fire. Never dispose of
batteries in a fire.• There are no user serviceable parts inside the DVR-5HD,
the battery can only be replaced by an authorised Snooper technician.
• Dispose of used batteries by observing local regulations.• Disposed of used batteries observing local regulations.
WEEE
Battery
4DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
Notes on Installation
1. Before installing the device, measure the front windshield viewingarea, make sure not to block the driver’s front view,install the devicebelow the rear view mirror (the central, higher right position of thefront windshield). And we recommend that the sky and the landeach occupy 50% of the screen, fix the carholder and then adjustthe device so that the lane ahead is aligned with the screen. Properinstallation enables the device to maximize the efficiency and canalso enhance the accuracy of LDWS.
2. Make sure that the lens is within the wiping range of the windscreenwiper to ensure a clear view when it rains.
3. Do not touch the lens with your fingers. Finger grease may be left on the lens and will result in unclear videos or pictures. Clean the lenson a regular basis.
4. Do not install the device on a tinted window. Doing so may damagethe tint film.
5. Make sure that the installation position is not hindered by the tintingon a window.
6. This product is suitable for light windshield or light colour heat-resistant film windows, it will affect video quality if it is installed ondark tinted windows or windows with dark heat-resistant film.
7. Only use the supplied battery charger. Do not use any other branded battery charger, using any other charger may cause damage to yourequipment or may cause the battery to explode.
8. The suction cup bracket is designed for temporary mountingand will require periodic re-installation. The adhesive bracket isdesigned for one time and long term installation. We recommendusing the adhesive bracket if permanent installation is desired. Weare NOT liable for any damages or data loss due to improper bracket mounting or the suction cup bracket losing suction and falling off.
5DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
CautionDue to local laws and vehicle safety considerations, do not operate this device while driving.• Set up time zone, time and date accurately before you use
this device.• Please use Snooper Player software only if the Maps are
functioning correctly.• The firmware function in the device is for reference only, drivers
are advised to exercise discretion based on actual roadconditions.
• The results of GPS positioning are only for reference, and shouldnot be used to affect the actual driving situation. The devicecannot ensure total positioning accuracy.
• GPS positioning accuracy may differ depending onweather conditions and the location, such as high buildings,tunnels, undergrounds, or forests. GPS satellite signals cannotpass through solid materials (except glass). Tinted windows willalso affect the performance of the GPS satellite reception.
• GPS reception performance may differ on each device. The device cannot determine the accuracy of positioning data from differentdevices.
• The values displayed in this device, such as speed andposition, may be inaccurate due to the influence of the surrounding environment. They are for reference only.
• This product should only be used for non-commercial use withinthe limits permitted by the appropriate laws. We do not take anyresponsibilities for the loss of use of the product.
• It is normal for this device to become warm during use.• Improper use or operation of the product may result in damage to
the product or its accessories and will void the warranty.
Before you start using the product, it is assumed that you agree to the above statement.
6DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
1 IntroductionThank you for purchasing this advanced drive recorder. This product is specifically designed for real time video recording when driving.
1.1 Features• SONY Sensor, low light enhancement• Full HD 1920* 1080• 3.0” TFT-LCD colour screen• 155° Wide angle lens• Collision Detection, when a collision is detected, the device will
automatically trigger the emergency recording function• Parking Mode (Motion detection, Vibration detection)• Multifunction traffic safety reminder• Rear Camera 1080p (DVR-5HD only)
1.2 Package ContentsThe package contains the following items. If there are any missing or damaged items, contact your dealer immediately.
Drive Recorder
Quick Start Guide
Bracket X2
Car Adapter
Do NOT install the bracket in a location that may obstruct your field of view and impact driving safety.
7DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
1.3 Product Overview
No. Item
1 Menu / Back Button ( / )
2 Add Speed Point / Up Button ( / )
3 Snapshot / Down Button ( / )
4 Emergency Recording / Confirm But-ton ( / )
5 Switch Camera Button ( 2CH)
6 LED Indicator
7 LCD Colour Screen
8 Speaker
9 Wide Angle Lens
No. Item
10 Reset Hole
11 Microphone
12 Power Switch
13 Power Connector Port
14 Memory Card Slot
15 HDMI Connector Port
16 Rear Camera Connector Port (option)
17 Bracket Socket
Please press the button (1~5) according to the diagram notice shown on screen.
8DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
1.4 Product Overview – Rear camera (DVR-5HD only)
No. Item
1 Wide Angle Lens
2 Base
3 Micro USB Connector Port
4 Camera Rotation Shaft
5 Rear/ front image switch
9DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2 Getting Started2.1 Storage Media2.1.1 Insert the Memory CardInsert the memory card with the contacts facing towards the screen of the device, see the illustration below. Push the memory card in until you hear a click, indicating the card is in position.
2.1.2 Remove the Memory CardIf the device is powered on, please power off first and wait for the device to completely power down before ejecting the memory card.
Note:1. Do not remove or insert the memory card when the device is
turned on. This may damage the memory card.2. Support SDHC class 10 and memory storage of 8GB or above
(supports up to 32GB).3. Please format the micro SD cards before the initial use. The
formatted file type for this device is FAT32 file.4. When removing the memory card, be careful that the card may
spring out and become lost. The memory slot has this spring- out feature for easy removal of the card.
10DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2.2 Installation in Vehicles2.2.1 Mount to Windshield
11DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2.2.2 Adjusting the device position
12DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2.3 Connecting to the Power SupplyOnly use the supplied car adapter to power this device and charge the built-in battery.1. Connect one end of the car adapter to the power connector
port on the device. USB port input: DC 5V / 1.0A.
2. Plug the other end of the car adapter to the cigarette lightersocket of your vehicle. Once the vehicle engine starts thedevice will automatically power on. Car adapter input: DC 12 /24V.
Please measure the front windshield viewing area. So as not to block the driver’s field of view, install the device under the driving mirror (upper center of the front windshield). We recommend that the sky and the land each occupy 50% in the recording screen, please adjust the device so that the alignment icon is correctly aligned with the driving lane. Proper installation enables the device to operate with maximum efficiency and improve the accuracy of LDWS.
13DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2.4 Installation in Vehicles – Rear Camera (DVR-5HD only)2.4.1 Mounting Rear Camera to the Windshield
1. Remove the white paper from the doublesided tape, stick it onto the base of therear camera, then firmly press the double sided adhesive tape to ensure its firmlystuck.
2. Adjust the rear camera as illustratedbelow: please check the recordingdirection is aligned correctly beforeinstallation.
3. Connect the USB cable with the primary camcorder and power it onto enter the preview screen and confirm the field of view. Then cleanthe surface of the windshield with alcohol to ensure that the adhesion surface is clean.
4. Remove the red paper on the double sided adhesive tape.5. Install the rear camera onto the windshield, firmly press the pad to
ensure its firmly stuck.
Rear view recording In-car recording
14DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
Note:1. Do not install the device on a tinted window. Doing so may damage the tint film.2. This product is suitable for light windshield or light colour heat-resistant film
windows, it will affect video quality if installed on dark windows or dark heat-re sistant film windows.
15DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2.4.2 Adjusting Rear Camera (DVR-5HD only)
1. Once the rear camera is mounted to the rear windshield, thelens should be rotated to accommodate the external rear viewas illustrated below.
2. Slide the switch to “Rear”.
3. Use the preview screen on the front camera to fine tune thedesired lens angle.
16DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
1. Once the rear camera is mounted to the rear windshield, the lens should be rotated to accommodate the internal cabin view as shown by the illustrations below.
2. Slide the switch to “Front”.
3. Use the preview screen from the front camera to fine tune the desired lens angle.
We recommend users to disconnect the micro USB cable from rear camera before adjusting.
17DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2.5 Connect and Set Up Rear Camera (DVR-5HD only)Use the USB cable from the rear camera package to connect between the front and rear cameras. (Rear camera is included in the DVR-5HD package only. Please contact distributor for further information.)
1. Plug phone jack into the front camera’s 2CH port. (Front camerashould be powered off.)
2. Plug the other end of the USB cable (micro USB connector) intothe rear camera’s USB port.
1. Install the rear camera in the upper central position of the rear windshield. 2. The rear camera doesn’t support hot Plug-n-Play. Please turn off the front
camera before plugging in the rear camera. 3. If you change to the other rear camera, after Menu setting, you will need to
re-power on the front camera.
18DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2.5.1 Battery Status Indicator
2.6 LED Indicator
Icon Description
Full battery power.
2/3 battery power.
1/3 battery power.
Out of battery power.
Battery is charging.
Connect to the car adapter & the battery is fully charged.
NOTE:1. To avoid equipment overheating and possible catastrophic damage to the
battery, please only use the supplied car adapter. Do not use any other brand of car adapter, any damage caused by using any other adapter than the one supplied will void your products warranty.
2. Please note, if the environmental temperature reaches 45°C or above, the car adapter can still supply power to device, but it will not charge the Lithium-ion battery. This is a characteristic of Li-polymer and is not a malfunction.
Power off, battery charging Red
Power off, battery full charged LED light off
Power on, battery charging Red
Power on, battery full charged Green
Standby / Standby with screen off Green
Recording/ Recording with screen off Flashing red
19DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2.7 Powering the Device On / Off and Resetting2.7.1 Auto Power On/OffIf the device is connected to the vehicle power supply, start the car engine, the device will automatically power on and start recording.Once the vehicle engine shuts down, the device automatically saves the recording and powers off within 10 seconds.
2.7.2 Manual Power On/OffTo manually turn on the power, press the POWER button. To turn off, press and hold the POWER button for at least 2 seconds.
2.7.3 Reset In case the device fails to function normally due to unknown causes, insert a pin or paper clip into the Reset hole for 5 seconds to restart the device.
20DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2.8 Initial SettingsBefore using the device, we recommend you setup the correct Time zone, Date and Time.
2.8.1 Set the Time Zone
To set the time zone, do the following:1. Press the / button to enter the OSD menu.
2. Press the or button to select Set Time Zone, and then press the button to enter the function menu.
3. Press the or button to set the current time zone, and then press the button to save the setting.
4. Press the button to return to recording screen.
Please note that if you press the / button during recording, the system will stop recording and enter the OSD menu. Before accessing the menu make sure the recording is stopped.
21DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
1. If Satellite Synchronization is on, the device clock will be set via satellite clock signal based on the Set Time zone. 2. If satellite positioning is not available, the device clock will run based on the user defined time.
22DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2.8.2 Set the Date / TimeTo set the correct date and time, do the following:
1. Press the / button to enter the OSD menu.
2. Press the or button to select Date / Time, and then press the button to enter the function menu.
3. Press the or button to adjust the value, and then press the button to set the data and proceed to the next field.
4. Repeat step 3 until the date and time setting is completed.
5. Press the button to return to recording screen.
To ensure the accuracy of the video file time, please reset the date and time when the battery power runs out or when not in use for more than 7 days.
23DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3 Using the Drive Recorder 3.1 Automatic RecordOnce the car engine starts, the device will automatically power on and start recording.Recording will automatically stop when the engine is switched off.
1. Some vehicle power supplies do not turn on / off automatically when the car engine starts. If the device cannot automatically power on / off with the car engine, please manually connect the power supply to the vehicle power, and then power on, or manually power off the device and then remove the connector from the vehicle power supply.2. The recorder can be configured to save a video file every 30 seconds, for between 1 to 3 minutes duration. 3. All the videos and photos are saved on the memory card, if memory card is full, loop recording will overwrite the oldest video file.
24DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3.1.1 The Front Camera’s Recording Screen
No. Icon Item Description
1 Recording Duration Indicates the current video duration.
2 Date / Time Indicates the current recording date and time.
3 Menu During video recording, press the button to enter the OSD menu.
4 Add Speed Cam Position
During video recording, press the button to add a speed cam position.
5 PIV (Picture in Video)
Press to capture video screen shots from the primary camcorder.
6 Emergency Recording
During video recording, press the button to record emergency file.
7 Switch Camera Preview
Press to switch preview screen.
8 Satellite Positioning
Indicates the strength of satellite positioning. If the icon shows in red on screen, it indicates that the camcorder cannot complete the satellite positioning.
25DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3.1.2 Emergency Recording
To Start the Emergency Recording, do the following:1. During Video Recording, press the / button to enter
No. Icon Item Description
9 Speed Current driving speed.
10 Voice Record Indicates voice recording muted, sound will not be recorded.
11 Resolution Indicates the video resolution.
12 Micro SD Card When a compatible micro SD memory
card is inserted, the LCD displays .
If no memory card is inserted or if the memory card is damaged / incompatible, the LCD displays
13 Battery Indicates battery status.
14 VIV (Video in Video)
Rear camera recording screen.(DVR-5HD only)
26DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
emergency recording mode, the “Emergency” message will be displayed immediately at the upper left corner of the screen, and the recorded file will be protected.
2. The emergency video recording length is the same as the recording interval setting. When the emergency recording duration reaches the interval setting, the system will return to the general recording mode.
3.2 Add Speed PointYou may customize speed cam positions in this product.1. When the GPS positioning is active, press / to update speed camera points.
Note:1. If the Collision Detection function is enabled and a collision is detected, the device will automatically trigger the emergency recording. 2. The emergency file is created as a new file and is saved in the Event folder, which will be protected to avoid being overwritten by normal loop recording. The emergency video folder will occupy 40% of the available memory card capacity. For example, if you use 8GB memory card, about 3.2GB memory space will be reserved for emergency files. When the event folder is full, the oldest emergency file will be automatically deleted by the newest emergency file.
27DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
2. This product features a capacity for 200 speed cam positions. In case you are trying to add more than that the system will prompt with the message “Speed Position is full”.
3.3
Picture in VideoYou can use this device to take snapshots of the current view.1. In recording status, press / to capture screen shots from the front lens.2. When the icon shows in the centre of the screen, it means the screenshot is captured.
3.4 Driving Safety
Note:You may delete custom speed cam positions by selecting the Delete Last Position or Delete All Position option from the Speed Position Management menu. Please note that all of your existing speed cam positions are deleted once the Delete All Position option is selected. Make sure you are ready to recreate your custom speed cam positions before running this option.
Note:1. The screenshot image resolution quality is dependent on the video resolution setting. 2. The picture resolution is limited by the speed of the target object and the quality of the ambient lighting. The screenshot function is better used for taking still pictures in accident scenes or when the car is stopped waiting for a traffic light.
28DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3.4.1 Speed Limit Alert If the Speed Limit Alert function is enabled, once your car’s location is determined by GPS and approaches a speed cam, this product produces an audible alert and onscreen message.To enable the Speed Cam Alert: 1. Press the button to enter the OSD menu. 2. Press the / button to select Speed Limit Alert, and
then press the button to enter the function menu. 3. Press the / button to select On, and then press the
button to enable the function.4. Press the button to return recording screen. 5. The alarm screen turns red to
remind you to slow down if you are driving faster than the speed limit.
The following driving safety function is for reference only. Drivers are advised to exercise discretion based on actual road conditions.
1. The Driving Safety function is limited to triggering no more than two alarms at the same time. If a voice and alert message have been triggered, any other alarm will be ignored until either of the two is settled.2. Satellite positioning must be completed before functions such as Speed Cam Alert, Speed Position Management, Speed Limit Alert, LDWS and FCWS should be enabled. Be sure to check that Satellite positioning has been completed prior to using the product.3. The detections of LDWS and FCWS may be inaccurate when used in rain, at night or in environments with insufficient lighting. Drivers are advised to exercise discretion based on actual road conditions.
Note:The Speed Cam Alert function must have the speed cam datum from the country you use. The function will be void if the product is used in any other countries. Please consult with the shop you purchased from if the function is void. There is no guarantee the speed cam datum will be included for other countries.
29DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3.4.2 Speed Limit Alert If the Speed Limit Alert function is enabled, this product produces an audible alert and screen message once your car’s location is determined by GPS and its running speed exceeds the set limit.To activate the Speed Limit Alert, do the following: 1. Press the button to enter the OSD menu. 2. Press the / button to select Speed Limit Alert, and then
press the button to enter the function menu. 3. Press the / button to set up a Speed Limit Alert to trigger
this product’s alarm [Off / 50 ~ 200 km/h (30~125 mph)], and then press the button to complete setting.
4. Press the button to return recording screen. 5. The alarm screen turns red to
remind you to slow down if you are driving faster than the speed limit.
30DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3.5 Parking Mode To monitor the vehicle when it is parked, you can activate Vibration Detection, or Motion Detection.Follow the steps below to change the settings for Parking Mode: 1. Press the / button to enter the main menu.2. Press the or button to select Parking Mode, and then press the button to confirm.3. Press the or button to configure Parking Mode (Off / Vibration Detection / Motion Detection), and then press the button to complete setting.4. Press the button to return to the recording screen. • Off: No parking monitoring activated.• Vibration Detection: - If disconnected from the external power supply when the device is powered on, the system will display the alert message “Press OK to power off or enter Vibration Detection after 10 sec”. This means the system will power off and enter Vibration Detection automatically in 10 seconds. - Once Vibration Detection Mode is triggered, when the device detects any vibration, it will automatically power on and start recording, the event will be recorded for 60 seconds (per file). - In this mode, the device is powered off until the event happens. This mode uses power saving. - To disable this function, in vibration detection recording, press any key to wake up the screen, and resume to normal loop recording; or when the car engine is started again, it will be return to normal loop recording.
31DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
• Motion Detection: - If disconnected from the external power supply when the device is powered on, the system will display the alert message “Press OK to power off or enter Parking mode after 10 sec”. This means the system will enter Motion Detection automatically in 10 seconds, and then the LCD screen turns off (the device will turn off the screen temporarily, but will remain in standby detection status. Press any button to turn on the operation screen and resume normal loop recording). - In Motion Detection mode, when the device detects any motion in front of the lens, automatic recording will be activated. - In this mode, when the device detects any motion in front of the lens, video recording will be triggered and the event will be recorded for 10 seconds (per file). If the event lasts more than 10 seconds, the device will continue recording up to 2 minutes. - In this mode, the device is in standby mode until an event happens. This mode will consume more battery power. - To disable this function, in the standby mode or motion detection recording, press any key to wake up the screen, and resume normal loop recording; or when the car engine is started again, it will be return to normal loop recording.
Note:1. If the battery is fully charged, it can record about 30 minute’s video in Motion Detection mode. As the device is used, the battery storage capacity will decrease gradually. This is a normal phenomenon for the battery.2. The video files taken in Vibration Detection mode will be saved in the Event recording folder, which will not be overwritten by normal video files.3. The video files taken in Motion Detection mode will be saved in the normal recording folder.
32DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3.6 Collision Detection If the Collision Detection function is enabled, this device begins emergency recording once it detects any collision. The sensitivity of the Collision Detection function is set to Normal by default, to change the settings of Collision Detection:
1. Press the / button to enter the OSD menu.
2. Press the / button to select Collision Detection, and then press the button to enter the function menu.
3. Press the / button to change the sensitivity of this device’s Collision Detection (Off / High Sensitivity / Normal Sensitivity / Low Sensitivity), and then press the button to set the sensitivity.
4. Press the button to return recording screen.
33DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3.7 Driver Fatigue AlertIf the Driver Fatigue Alert function is enabled, this product produces an audible alert and screen message one hour after it has begun recording and repeats the alerts every half hour afterwards.To enable the Driver Fatigue Alert, do the following:1. Press the button to enter the OSD menu.2. Press the / button to select Driver Fatigue Alert, and
then press the button to enter the function menu.3. Press the / button to select On, and then press the
button to enable the function.4. Press the button to return recording screen.5. This product produces audible alert and screen message when
Driver Fatigue Alert activates.
3.8 LDWS Once your car’s location is determined by GPS and the LDWS function is enabled, this camcorder produces an audible alert and screen message when you deviate from or change lanes at speeds over 70 km/h (43 mph).To set the LDWS (Lane Departure Warning Systems):
1. Press the button to enter the OSD menu.2. Press the / button to select LDWS, and then press the
button to enter the function menu.3. Press the / button to select On, and then press the
button to enable the function.4. Press the button to return recording screen.
34DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
5. After enabling LDWS, the screen will display a traffic lane align icon in green , please adjust the camcorder so the slash lines are centred in the driving lane.
6. This product produces an audible alert and screen message when LDWS is activated.
Note:1. Please measure the front windshield viewing area, do not block the driver’s forward field of view, and install the camcorder below rearview mirror (upper center of the front windshield). We recommend that the sky and the ground both occupy 50% of the video screen, install the bracket then adjust the camcorder to ensure the lane is aligned to the lane alignment icon. Correct installation maximizes the efficiency and improves the accuracy of the LDWS function.2. Make sure that the traffic lane align icon will not be obscured by other things (e.g. hood). It may cause misjudgment if the endpoint is obscured.
35DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3.9 FCWSOnce your car’s location is determined by GPS and the FCWS function is enabled, this camcorder produces an audible alert and screen message when you drive at speeds over 60 km/h (37 mph) and are less than 20 m away from the car in front of you. If the camcorder is not connected to a satellite, and the distance from the leading vehicle is below 20 meters, it will also produce a warning screen and an audible beep reminder.To set the FCWS (Forward Collision Warning System):
1. Press the button to enter the OSD menu.2. Press the / button to select FCWS, and then press the
button to enter the function menu.3. Press the / button to select On, and then press the
button to enable the function.4. Press the button to return recording screen.5. This product produces audible alert and screen message when
FCWS activates.
36DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3.10 2 Grid Function Chart When the camcorder is recording, pressing the Power button will enter the 2 GRID FUNCTION CHART in the LCD screen, users can
check vehicular information here. Pressing the Power button once again will return to your recording.
1 Driving Speed 2 Driving direction
Note:Driving Speed and Driving Direction are only applicable when satellite positioning is active; otherwise, they will be displayed grayed out. Satellite positioning function is dependent on the model purchased.
37DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3.11 Playback Videos and Photos3.11.1 Playback1. Press the / button to enter the OSD menu.
2. Press the / button to select Playback, and then press the button to enter the function menu.
3. Press the / button to select file types (Video / Event / Picture), and then press the button to enter menu.
4. Press / button to browse the files, select the file and then press the button to enter Playback Mode.
5. Press the repetitively to return recording screen.
38DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3.11.2 Playback Mode3.11.2 Playback Mode
No. Icon Item Description
1 File Type Indicates the type of file currently playing.
2 File Name Indicates the file name of video / picture.
3
Duration / Total
recorded time
Indicates the video elapsed time / Indicates total recorded time.
Date and time Date and time the photo was taken.
4 Return
Press the button to return to preview screen of video or picture. Press the button repetitively to return to the recording screen.
5 Previous File
Button Press button to view previous file.
6 Next File Button
Press button to view next file.
7 / Playback/
Pause button Press the / / button to play or pause the video.
Video Playback Screen Picture Playback Screen
6
1
345
9
11
7
2
8
10
1
3456
9
11
2
8
10
DVR-4/5 HD Gen2 V1.2 EN 04/18 39
No. Icon Item Description
1 File Type Indicates the type of file currently playing.
2 File Name Indicates the file name of video / picture.
3
Duration / Total recorded time
Indicates the video elapsed time / Indicates total recorded time.
Date and time Date and time the photo was taken.
4 Return Press the button to return to preview screen of video or picture. Press the button repetitively to return to the recording screen.
5 Previous File Button
Press button to view previous file.
6 Next File Button Press button to view next file.
7 / Playback/Pause button
Press the / / button to play or pause the video.
8 TF Card When a compatible memory card is
inserted, the LCD displays . If no memory card is inserted or if the memory card is damaged /
incompatible, the LCD displays
39DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
3.12 Deleting FilesTo delete file(s), perform the following steps:
1. Press the / button to enter the OSD menu.
2. Press the or button to select File Deletion, and then press the the button to enter the function menu.
3. Press the or button to select file types (Video / Event / Picture), and then press the button to enter the menu.
• Delete One: - Press the or button to select Delete One, and then
press button to enter the menu.
No. Icon Item Description
9 Battery icon Indicates battery power and charging status.
10 Serial Number Shows the current file number and total file number.
11 Time Stamp Indicates the date and time of the video or photo.
40DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
- Press or button to browse files, select the files you want to delete and then press button to enter the menu.
- Press the or button to select item, and then press the or button to confirm or cancel the selection.
• Delete All:- Press the or button to select Delete All, and then press
button to delete all the files in this file type.
- Press the or button to select item, and then press the or button to confirm or cancel the selection.
4. Press the repetitively to return recording screen.
Note:Deleted files CANNOT be recovered. Ensure the files you wish to preserve are backed up before deletion.
41DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
4 Adjusting the Settings 4.1 Using the MenuRefer to the table below for details of the main menu and function list.
Menu option Description Available option
Playback Select the file category that you want to view. (Rear camera only available with DVR-5HD)
Video (Front camera)Video (Rear camera)Event (Front camera)Event (Rear camera)Picture (Front camera)Picture (Rear camera)
Satellite Status Displays the current state of the satellite reception.
Satellite Synchronization
If the satellite time is enabled, the drive recorder clock will synchronize according to the satellite time zone you set. When you turn on this feature, it will display the satellite time preferentially, and cannot be manually changed.
On / Off
Speed Unit The system displays the speed setting unit.
KM/H / MPH
Speed Cam Alert
If the Speed Cam Alert function is enabled, once your car’s location is determined by GPS and approaches a speed cam, this product produces an audible alert and screen message.
On / Off
Speed Position Management
Add Speed Point: The satellite positioning will manually add speed camera location. You can add up to 200 speed camera locations to the built-in system.Delete Last Position: Delete the last speed camera point. Delete All Position:Delete all speed camera points.
Add Speed Point / Delete Last Position / Delete All Position
Speed Limit Alert
Set a customized maximum speed limit. When the vehicle speed exceeds the maximum, an audible alert is automatically triggered and a warning message is displayed on the screen.
Press the / button to set the speed limit. You can set it off, or set speed limit from 50 to 200km/h (30 to 125mph) 42DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
Menu option Description Available option
Set Time Zone Set the time zone you are in. Press the / button to set the satellite time. You may customize it between GMT -12:00 ~ GMT +13:00
Date / Time Set the date and time. Press the / button to adjust the value, and then press the button to set the next field, and complete setting
Language Language setting. English∕ Español/Deutsch/ Italiano/Français/Nederlands
Time Stamp If the time stamp is enabled, recorded files or photos will show the date and time.
On / Off
Resolution Setting of video resolution. 1080P 30fps / 720P 30fps
EV Setting of exposure value. Press the / button to set the exposure value. It can be set between -2 ~ +2
LCD Setting Set LCD off time. Device screen will be off after a set time if no operation is detected during the standby or record mode. Pressing any button will switch it on. (Recording is not affected when screen is off).
On / Turn Off After 7 sec. / Turn Off After 1 min. / Turn Off After 3 min.
Voice Record Setting for activating audio in the video. On / Off
Key Tone Enable / disable key tone. On / Off
Volume Adjust the power-on sound and key tone volume.
Press the / button to set the volume. It can be set between 0 ~ 10.
43DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
Menu option Description Available option
Record Interval Save respective video files in a length of the selected duration.
30 sec. / 1 min. / 3 min.
Parking Mode If one of the parking modes is activated, the device will enter parking mode 10 seconds after disconnecting from the external power source.
Off / Vibration Detection / Motion Detection
Collision Detection
If Collision Detection is activated, this device starts an emergency recording once it detects any collision.
Off / High Sensitivity / Normal Sensitivity / Low Sensitivity
Driver Fatigue Alert
When Driver Fatigue Alert is enabled, audible alert and screen message will be activated 1 hour after the camcorder is powered on, with a repetition every 30 minutes.
On / Off
LDWS Once your car’s location is determined by GPS and the LDWS function is enabled, the camcorder produces an audible alert and screen message when you deviate from or change lanes at speeds over 70 km/h (43 mph).
On / Off
FCWS When FCWS is activated after satellite positioning, the camcorder will issue an audible alert and screen message when vehicle speed is above 60 km/h (37 mph) and the distance between the front vehicle is less than 20m.
On / Off
File Deletion Delete the file(s). Video / Event / Picture
Anti-flicker Domestic power supply varies by area. It is recommended that you should check the “Table of voltage and frequency of different countries” for the correct setting.
60 Hz / 50 Hz
Format Format the inserted memory card. All the files on the card will be erased.
Yes / No
Default The system reverts to the default settings.
Yes / No
Firmware Version
Indicates the current firmware version.
44DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
5 Connecting to Other Devices 5.1 Connecting to the Computer
You can connect the device to a desktop computer or notebook to transfer or view files. 1. Connect micro USB cable to the device micro USB port. 2. Connect the other end of USB cable to an available USB port of
your computer.
1. This only indicates the device can connect to the computer; micro USB cable is not included in standard package.
2. Under dual-lens mode, the recording files will be saved separately in differentfolders, "F" folder is for front camera files, "R" folder is for rear camera files.
3. If user only deletes front camera files with on computer, then the rear camera files would be unavailable, also it couldn’t be overwritten by loop recording. To avoid residual files occupy memory capacity, please delete thefiles by computers, or format the memory card by the device. Please refer to Format (4.2).
56
5 Connecting to Other Devices5.1 Connecting to the ComputerYou can connect the device to a desktop computer or notebook to transfer or view files.1. Connect micro USB cable to the device micro USB port.2. Connect the other end of USB cable to an available USB port of
your computer.
3. Power on the device, the computer screen will show up the message when the computer detects your device, select "Openfolder to view files", or open the "Removable Disk", then userscan save the files to your computer.
Note:
4. If user only deletes rear camera files with on computer, then the device can only review the front camera files which hasn’t been deleted.
5. The micro USB cable will not supply the power to the device, please power on the device and make sure it has enough battery power, or take out the memory card to read the files.
3. Power on the device, the computer screen will show the message “Open folder to view files”, or open the “Removable Disk” when the computer detects your device. Confirm the message and then users can save the files to your computer..
Note:This only indicates the device can connect to the computer; mini USB cable is not included in standard package.
45DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
5.2 Connecting to TVYou can use HDMI cable transfer to TV to play the file. 1. Power on the device. 2. Connect HDMI cable to device HDMI port. 3. Connect HDMI cable to TV HDMI port.
4. Power on TV, switch TV signal input to HDMI, use the / / / buttons to operate the device.
Note:1. It only indicates this device can connect to TV, HDMI cables are not included in the standard package.2. Please make sure the device is powered on before using the HDMI cable to connect to the TV.
46DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
6 Installing the Software
1. Place the attached CD ROM into the CD drive. 2. If the CD does not execute automatically, please use Windows File Manager to execute the Install_CD.exe file on the CD.
The following screen will be displayed.
3. Press the [Menu] item to start the installation process and follow the instructions on-screen.
47DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
6.1 Updating Speed Camera data
Updating the speed trap data is simple.Register your DVR5-HD at http://www.snooperneo.co.uk once registered, follow the on screen instructions.For subsequent downloads please follow the instructions below:
1. For DVR-4HD Gen 2 go to or click on the link below: https://www.snooperneo.co.uk/SoftwareDVR.cfm?type=305 and enter your serial number. For DVR-5HD Gen 2 go to or click on the link below: https://www.snooperneo.co.uk/SoftwareDVR.cfm?type=306
2. Download by clicking the link on the webpage, when prompted save the file to your PC.
3. Unzip/decompress the downloaded file and copy the 2 files “SdFwCode.bin” & “DVR401.bin” into a micro SD card.
4. Insert the micro SD card into the DVR-4HD or DVR-5HD gen2.
5. Press the button, and then connect a power adaptor to power on the dash camera. You can release the button when you see the firmware begin to update.
6.
Do not disconnect power form the device until the update has completed.
7. Once the update has completed the device will switch off. The device will automatically delete the .BIN file from the SD card.
48DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
7. Snooper DVR Player
No. Item
1 Front Camera View
2 Rear Camera View
3 File name*
4 Google Map view
5 Current File details
6 Speed kmh/mph
7 Compass
8 Play back controls
No. Item
9 G sensor
10 Volume control
11 Browse files
12 Playback Duration / Total Duration
* For file playback ONLY select file from the Front (F) folder
Note:1. To display the route on Google Maps, please make sure the internet is connected before starting the video playback.2. Video files recorded using the front camera (MOV) and the GPS/G-Sensor files (NMEA) must be stored in the same folder before starting the playback. 3. The Snooper DVR software is only available on the Windows operating system.
49DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
8 Specifications
Item Description
Image sensor 1/2.9” SONY sensor
Effective pixels 1920 (H) x 1080 (V)
Storage media Supports Micro SDHC, up to 32GB class 10 speed or greater
LCD display 3” LCD colour TFT
Lens Wide Angle Fixed Focus lens, Aperture: Up to F1.8
Focus range 1.5m~Infinity
Satellite System GPS
VideoResolution: Full HD 1920 x 1080 @ 30fps HD 1280 x 720 @30fps
Format: MOV
Still image (Photograph)
Resolution: depends on video resolution setting
Format: DCF (JPG)
Shutter Electronic shutter, Auto: 1/33 • 120~1/30 sec.
G-Sensor 3-Axis G-Force sensor
ISO Auto
White Balance Auto
Microphone Built-in
Speaker Built-in
Interface Mini USB, A/V port, HDMI
Battery Built-in Li-polymer rechargeable (This battery is NOT replaceable)
Operating Temperature
0° ~ 60° C
Operating Humidity
20 ~ 70% RH
50DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
Rear Camera (DVR-5HD only):
Item Description
Storage Temperature
-20° ~ 70° C
Dimensions 87.6 x 53 x 28.5 mm
Weight Approx. 86g (without memory card)
Item Description
Image Sensor 1/2.9” SONY sensor
Effective Pixels 1920 (H) x 1080 (V)
Lens Wide Angle Fixed Focus lens F2.0, f=3.8mm
Focus Range 1.5m~Infinity
Movie Clip Resolution: FHD@30 (1080P 30fps)Format: MOV
Operating Temperature
0° ~ 50° C
Storage Temperature
-20° ~ 70° C
Dimensions 65 x 36.5 x 25.5 mm
Weight Approx. 22g
51DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
9 Service Under WarrantySnooper comes with a standard 12 month manufacturer’s warranty. Register your device for warranty at www.snooperneo.co.ukFaulty Products up to 30 days from purchase.Refund or Replace Policy, Contact Seller directly for this. The consumer is responsible to ensure software is up to date. All products must be complete with accessories and original packaging on return.Faulty Products from 31 days to 12 months from purchase.Snooper (Performance Products Ltd) will offer a prompt repair service. In all cases we reserve the right to inspect the product and verify the fault. Contact Seller for their returns procedure, all warranty claims MUST go through the seller. Consumer is responsible for software updates!We do not cover faults caused by accident, neglect, misuse or normal wear and tear. All products must be complete with accessories and original packaging on return.PLEASE NOTE:We cannot process any warranty claims unless proof of purchase is provided.Please retain your receipt as a precaution.Full terms and conditions of warranty are available on request.Limited WarrantyThis Snooper product is warranted against all defects in materials and workmanship for a period of one (1) year from the date of original purchase, when purchased from an authorized Snooper dealer.ALL PURCHASES OF SNOOPER PRODUCTS FROM NON-AUTHORIZED SNOOPER DEALERS ARE SUBJECT TO FURTHER WARRANTY RESTRICTIONS AS DESCRIBED BELOW.The conditions of this Limited Warranty and the extent of responsibility of Performance Products Ltd (PPL) under this Limited Warranty are as follows: 1. This Limited Warranty will become void if service is performed by anyone other than an approved Snooper Warranty Service Centre that results in damage to the product.2. This Limited Warranty does not apply to any product which has been subject to misuse, neglect or accident, or which has had the serial number altered, defaced or removed, or which has been connected, installed, adjusted or repaired, other than in accordance with the instructions provided by Snooper.3. Should you have any difficulties with the performance of this product during the warranty period, please call Snooper or visit our web site http://www.snooperneo. co.uk. You may also contact Snooper Customer Services at the address listed below for any service help you may need with Snooper products.4. PROOF OF DATE OF PURCHASE FROM AN AUTHORIZED SNOOPER DEALER WILL BE REQUIRED FOR ANY WARRANTY SERVICE OF THIS PRODUCT.5. SNOOPER PRODUCTS PURCHASED FROM A SOURCE OTHER THAN AN AUTHORIZED SNOOPER DEALER, INCLUDING ANY AND ALL PURCHASES VIA
52DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
THE INTERNET FROM A NON INTERNET AUTHORIZED SNOOPER DEALER, SHALL NOT BE COVERED BY ANY SNOOPER LIMITED WARRANTY TO THE EXTENT ALLOWED BY APPLICABLE LAW.6. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM EU COUNTRY TO EU COUNTRY.7. ALL IMPLIED WARRANTIES, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, SHALL HAVE NO GREATER DURATION THAN THE WARRANTY PERIOD SET FORTH ABOVE. UNDER NO CIRCUMSTANCES SHALL SNOOPER BE LIABLE FOR ANY LOSS OR DAMAGE, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT. BECAUSE SOME EU COUNTRIES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSIONS OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.8. Product must be shipped in its original carton or equivalent carton, fully insured, with shipping charges prepaid. Snooper will not assume any responsibility for any loss or damage incurred in shipping.9. The sole responsibility of Snooper under this Limited Warranty shall be limited to the repair of the product or the replacement of the product only (whichever is deemed appropriate and at the sole discretion of Snooper).10. This Limited Warranty does not cover car static or other electrical interferences, labour costs or any other associated or incidental costs incurred for the removal or reinstallation of the unit for repair.
Copyright © 2018All rights reserved.All other marks, products or company names mentioned in this guide are trademarks of their respective companies.
53DVR-4HD & DVR-5HD Gen 2 V1.4 EN 07/18
Performance Products Ltd, Cleaver House, Sarus Court, Manor Park, Runcorn,
Cheshire, WA7 1UL. Tel +44 (0)1928 579579 E: [email protected].
www.snooper.co.uk
SnooperUK @snooperuk Snooper UK