Upload
naveenkrishnas
View
229
Download
0
Embed Size (px)
Citation preview
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 1/26
Pressure drop
DL size 125 150 175 200 225 250 275 300 325
DL 1/2-2 470 540 600 650 700 750 800 850 890
DL 1/2-3 700 800 890 980 1.060 1.130 1.200 1.270 1.330
DL 1-2 940 1.070 1.190 1.300 1.410 1.510 1.600 1.690 1.780
DL 1-3 1.420 1.610 1.790 1.950 2.110 2.260 2.400 2.540 2.670
DL 1-4 1.910 2.150 2.380 2.610 2.810 3.010 3.200 3.380 3.560
DL 1-5 2.380 2.690 2.980 3.260 3.520 3.770 4.010 4.240 4.450
DL 1-6 2.820 3.220 3.580 3.910 4.230 4.520 4.810 5.080 5.340
DL 1-7 3.290 3.760 4.180 4.560 4.930 5.280 5.610 5.930 6.230
DL 1-8 3.770 4.290 4.770 5.220 5.630 6.030 6.410 6.770 7.120
DL 1-10 4.740 5.370 5.960 6.520 7.040 7.540 8.010 8.470 8.900
DL 2-8 7.570 8.590 9.540 10.430 11.270 12.060 12.820 13.550 14.520
DL 2-12 11.330 12.880 14.310 15.640 16.900 18.090 19.230 20.310 21.360
DL 2-15 14.170 16.100 17.890 19.550 21.120 22.610 24.030 25.390 26.700
DL 3-12 16.990 19.320 21.470 23.470 25.350 27.130 28.840 30.470 32.040
DL 3-14 19.820 22.540 25.040 27.370 29.570 31.650 33.640 35.550 37.380
DL 3-16 22.680 25.770 28.630 31.300 33.810 36.190 38.460 40.640 42.740
DL 4-15 28.320 32.190 35.770 39.110 42.240 45.220 48.060 50.780 53.400
DL 4-19 35.900 40.790 45.320 49.550 53.520 57.290 60.890 64.340 67.660
DL 5-18 42.540 48.310 53.670 58.680 63.380 67.850 72.110 76.190 80.120
Inertial Separator
• Factory assembled for easy
on-site installation
• Self-cleaning operation
• Low airow resistance
• Long service life
• Upto 92% arrestance on Arizona
Road Dust Coarse (AFI)
DustLouvre® Housing
Description
The Dust Louvre® Housing is a heavy duty
self-cleaning lter, equipped with an inertial
separator for ltration of dry, granularcontaminants. Typical applications include:
• Prelter for air conditioning and ventilating
systems in heavy industrial conditions.
• Prelter in areas with severe atmospheric
conditions, such as dust and sand storms.
• Air inlet lter in all types of industrial, public
and commercial buildings.
The Housing has one or more rectangular
air inlet aperture(s).
Behind each, a dust louvre pocket is
connected to the housing. A wire mesh
screen protects the aperture(s) and
louvre(s). The Dust Louvre® Housing is
available in nineteen sizes. The primary air
capacity of each housing is determined by
the pressure drop of each particular system.
The recommended pressure drop range is
125 Pa to 300 Pa over the housing.
The air capacity range is 540 - 80,120 m3/h.
Operating Principle
Uncleaned air enters the open end of
the V-shaped louvre pocket(s) and is
com-pressed in the smaller end of the “V”,
where the contaminant is removed fromthe airstream. The clean air exits via the
open louvre slots, while the dust is carried
downstream by inertia with the secondary
airow into the dust chute(s). Individual
chutes are connected by an external
manifold through which dust laden air isconveyed by the secondary air fan for
discharge.
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 2/26
AF-5-172-IN-082014 © 2014 AAF International
DustLouvre® Housing
Selecting the Housing The housing can be selected from the data
in the primary airow capacity table overleaf.
Selecting the Secondary FanThe secondary air capacity and resistance
can be selected from the curves.
The secondary airow should be set
between 7% and 10% of the primary airow.
If additional ducting is required from the fan,
the appropriate external resistance must be
added.
ArrestanceThe arrestance determined by the AFI test
procedure at rated air volume and 250 Pa.
pressure drop is:
- 92% on Arizona Road Dust Coarse
- 78% on Arizona Road Dust Fine
Bird-screen
Sec.
Air
E
J
B
Front elevation
(right hand discharge shown,left hand discharge optional
Side elevation
A H D
C
Rear elevation
50 50
50
50
25
25
25
175 x F25
10 mm holes
1 7 5
x
G
Air
Flow
15
Style
Code
Dimensions in mm Weight kg
A B C D E F G H J
DL 1 / 2 -2
DL 1 / 2 -3
DL 1-2
DL 1-3
DL 1-4
DL 1-5
DL 1-6
DL 1-7
DL 1-8
DL 1-10
DL 2-8
DL 2-12
DL 2-15 DL 3-12
DL 3-14
DL 3-16
DL 4-15
DL 4-19
DL 5-18
470
470
470
470
594
718
842
966
1089
1337
1089
1585
1956 1585
1832
2079
1956
2451
2327
400
400
400
400
400
400
400
400
400
400
800
800
800 1150
1150
1150
1500
1500
1850
196
196
196
196
196
196
196
196
196
196
291,5
291,5
291,5 291,5
291,5
291,5
291,5
291,5
291,5
850
850
850
850
850
850
850
850
850
850
920
920
920 920
920
920
920
920
920
198
198
198
198
198
198
198
198
198
198
410
410
410 410
410
410
410
410
410
2
2
2
2
2
3
4
4
5
7
5
8
10 8
9
11
10
13
12
1
1
1
1
1
1
1
1
1
1
3
3
35
5
5
7
7
9
17
17
17
17
17
17
17
17
17
17
50
50
50 75
75
75
90
90
90
200
200
200
200
200
200
200
200
200
200
400
400
400 504
504
504
504
504
504
26
26
26
26
32
36
42
46
53
61
96
124
146 174
194
217
258
318
372
- - - - - - - - -
100
200
300
400
500
600
700
800
900
1000
1100
0 500 15001000 2000 3000 4000 5000 6000 7000 80002500 3500 4500 5500 6500 7500
DL 2 -8 2 -1 2 2 -1 5 3 -1 43-12 3-16 4-15 4-19 5-18
-
100
200
300
400
500600
700
800
900
1000
1100
0 100 200 300 400 500 600 700 800 900 1000
DL 1/2-2 1-2 1-3 1 -4 1-5 1-6 1-7 1-8 1-10
- - - -- - - - -
1/2-3
Housing:
Louvre pockets:
Wire mesh screen:
Manifold:
Secondary fan:
galvanized steel or stainless steel: upto DL 1-10, 1mm - from DL 2-8, 1.5 mm
galvanized steel or stainless steel
galvanized steel or stainless steel
galvanized steel
direct driven centrifugal left or right hand discharge (other types available on request)
Technical Data
S e c u n
d a r y A i r F l o w
R e
s i s t a n c e ( P a )
S e c u n
d a r y A i r F l o w
R e s i s t a n c e ( P a )
Secundary Air Flow Capacity (m3 /h) Secundary Air Flow Capacity (m3 /h)
AAF has a poli cy of cont inuous product research and improvement and rese rves the righ t to change design and spec ifica tions
without notice. The presented data contains average values within existing specification tolerances. Initial resistance +/- 15%.
AAF-International B.V.
P.O. Box 60
7800 AB Emmen
The Netherlands
Tel: +31 591 686 911
Fax: +31 591 686 936
www.aafeurope.com
International AAF Offices:
Emmen (NL), Glika Nera (GR), Brussels (B),
Cramlington (GB), Oberhausen (D), Dubai
(UAE), Helsinki (Fin), Istanbul (TR), Lisbon
(P), Louisville, Ky (USA), Madrid (E), Mexico
(Mex), Mozzate-Co (I), Vincennes (F),
Bangalore (IND), Riyadh (KSA),
Shah Alam (Mal), Suzhou, Shenzhen (PRC),
Singapore, Taiwan, Brunn am Gebirge (A)
AAF Agents:
Johannesburg (RSA)
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 3/26
AAF INTERNATIONAL
v1.10.0.0
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 4/26
AAF INTERNATIONAL
AAF INTERNATIONALNum. Ref. Remark Model/Tool Qty. Speed (rpm) Rated
Mech.
Power (kW)
Max.
Electrical
Power (kW)
Design
flowrate
(m³/h)
Design
pressure
(Pa)
Flowrate
(m³/h)
Pressure (Pa)
1 1 CMAT-531-2T 1 2850 1.10 - 1103 900 1227.32 1114.25
2 2 CMAT-527-2T 1 2830 0.37 - 444 900 472.85 1020.67
3 3 CMAT-528-2T 1 2855 0.75 - 985 814 985.82 814.61
4 4 CMAT-528-2T 1 2855 0.75 - 610 1100 646.23 1233.93
5 5 CMAT-527-2T 1 2830 0.37 - 455 1050 455.17 1050.67
6 6 CMAT-531-2T 1 2850 1.10 - 1022 850 1191.47 1155.26
7 7 CMAT-527-2T 1 2830 0.37 - 448 1050 450.00 1059.25
TOTAL 7 - 4.81 - - - - -
2/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 5/26
INDEX
·
CMAT-531-2T (1) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4 CMAT-527-2T (2) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 7 CMAT-528-2T (3) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 10 CMAT-528-2T (4)
· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
13
CMAT-527-2T (5) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 16 CMAT-531-2T (6) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 19 CMAT-527-2T (7) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 22
3/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 6/26
Q (m³/h) 1227.30
Ps (Pa) 1114.28
Pd (Pa) 294.04
Pt (Pa) 1408.32
Impeller (rpm) 2850
Max. Temp. (ºC) 120
Outlet air speed (m/s) 22.14
Airflow maximum (m³/h) 1800
Speed (rpm) 2850
Approx. weight (kg) 24
Band Lw dB(A) Lp dB(A)
63 Hz 51 33
125 Hz 67 49
250 Hz 90 72
500 Hz 92 74
1000 Hz 89 71
2000 Hz 83 65
4000 Hz 77 59
8000 Hz 69 51
TOTAL 96 78
CMAT-531-2T AAF INTERNATIONAL (Ref.: 1)
Centrifugal single-inlet, medium-pressure fans with casing and straight-blade
impeller made from cast aluminium to transport dust and solids
Fan:
- Casing made from cast aluminium
-
Cast aluminium straight-blade impeller for models 324 to 531 and sheet steel for models540 to 545
Motor:
- Motors with IE-2 efficiency. except for motors with lower powers than 0.75 kW. single-
phase motors or two-speed motors
- Class F motors. with bearings. IP55 protection
- Three-phase 230/400V.-50Hz.
- Max. air temperature to transport: -20ºC.+ 120ºC
Finish:
- Anticorrosive finish in polyester resin. polymerised at 190ºC. after nanotech and
phosphate-free pre-treatment
On request:
-
Special windings for different voltages - Fan designed to transport air up to 250ºC
- ATEX certification. Category 2
CHARACTERISTIC CURVE AND ACOUSTICS AT 1.2KG/M³
Design Point
Q (m³/h) 1103
Ps (Pa) 900
Acoustics: Inlet, 3 (m), 1 plane
Service Point (SP)
TECHNICAL CHARACTERISTICS
Remarks Exclude. Transport materials
4/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 7/26
MOTOR DATA
Rated Mechanical Power (kW) 1.10
Hz/phases 50/3
Motor (rpm) 2860
Poles 2
Max. current (A) 380-415 V Y 2.40Max. current (A) 220-240 V D 4.20
Motor protection IP55
Motor frame size 80
Data can change, please check motor plate
AVAILABLE ACCESSORIES
INT C2V RM AR RFT/RFM AET RPA-20 B-150 ACE-150
It must be checked that the accessory is suitable for the fan model
5/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 8/26
DIMENSIONS
A A1 B C C1 C2 øD ød ød1 ød2 E H H1 øI
432 420 537 340 315 50 160 215 180 M6 189 320 200 200
øK øk øO øO1 V v X x1 Y
140 175 11 13 240 190 160 120 19
Dimensions without explicitly defined units are shown in millimeters (mm)
6/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 9/26
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 10/26
MOTOR DATA
Rated Mechanical Power (kW) 0.37
Hz/phases 50/3
Motor (rpm) 2710
Poles 2
Max. current (A) 380-415 V Y 1.11Max. current (A) 220-240 V D 1.92
Motor protection IP55
Motor frame size 63
Data can change, please check motor plate
AVAILABLE ACCESSORIES
INT C2V RM AR RFT/RFM AET RPA-17 B-125 B-100 ACE-125 ACE-100
It must be checked that the accessory is suitable for the fan model
8/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 11/26
DIMENSIONS
A A1 B C C1 C2 øD ød ød1 ød2 E H H1 øI
371 361 440 295 261 42 125 170 147 M6 168 260 170 155
øK øk øO øO1 V v X x1 Y
100 129 7 13 220 170 120 80 17
Dimensions without explicitly defined units are shown in millimeters (mm)
9/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 12/26
Q (m³/h) 985.59
Ps (Pa) 814.97
Pd (Pa) 254.23
Pt (Pa) 1069.20
Impeller (rpm) 2855
Max. Temp. (ºC) 120
Outlet air speed (m/s) 20.58
Airflow maximum (m³/h) 1400
Speed (rpm) 2855
Approx. weight (kg) 19.80
Band Lw dB(A) Lp dB(A)
63 Hz 49 31
125 Hz 64 46
250 Hz 89 71
500 Hz 85 67
1000 Hz 84 66
2000 Hz 79 61
4000 Hz 72 54
8000 Hz 65 47
TOTAL 92 74
CMAT-528-2T AAF INTERNATIONAL (Ref.: 3)
Centrifugal single-inlet, medium-pressure fans with casing and straight-blade
impeller made from cast aluminium to transport dust and solids
Fan:
- Casing made from cast aluminium
-
Cast aluminium straight-blade impeller for models 324 to 531 and sheet steel for models540 to 545
Motor:
- Motors with IE-2 efficiency. except for motors with lower powers than 0.75 kW. single-
phase motors or two-speed motors
- Class F motors. with bearings. IP55 protection
- Three-phase 230/400V.-50Hz.
- Max. air temperature to transport: -20ºC.+ 120ºC
Finish:
- Anticorrosive finish in polyester resin. polymerised at 190ºC. after nanotech and
phosphate-free pre-treatment
On request:
-
Special windings for different voltages - Fan designed to transport air up to 250ºC
- ATEX certification. Category 2
CHARACTERISTIC CURVE AND ACOUSTICS AT 1.2KG/M³
Design Point
Q (m³/h) 985
Ps (Pa) 814
Acoustics: Inlet, 3 (m), 1 plane
Service Point (SP)
TECHNICAL CHARACTERISTICS
Remarks Exclude. Transport materials
10/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 13/26
MOTOR DATA
Rated Mechanical Power (kW) 0.75
Hz/phases 50/3
Motor (rpm) 2770
Poles 2
Max. current (A) 380-415 V Y 1.60Max. current (A) 220-240 V D 2.78
Motor protection IP55
Motor frame size 71
Data can change, please check motor plate
AVAILABLE ACCESSORIES
INT C2V RM AR RFT/RFM AET RPA-18 B-125 ACE-125
It must be checked that the accessory is suitable for the fan model
11/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 14/26
DIMENSIONS
A A1 B C C1 C2 øD ød ød1 ød2 E H H1 øI
401 395 488 337 304 48 135 190 162 M6 178 288 177 190
øK øk øO øO1 V v X x1 Y
130 160 11 13 230 180 140 100 20
Dimensions without explicitly defined units are shown in millimeters (mm)
12/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 15/26
Q (m³/h) 646.10
Ps (Pa) 1234.05
Pd (Pa) 109.26
Pt (Pa) 1343.31
Impeller (rpm) 2855
Max. Temp. (ºC) 120
Outlet air speed (m/s) 13.49
Airflow maximum (m³/h) 1400
Speed (rpm) 2855
Approx. weight (kg) 19.80
Band Lw dB(A) Lp dB(A)
63 Hz 49 31
125 Hz 64 46
250 Hz 89 71
500 Hz 85 67
1000 Hz 84 66
2000 Hz 79 61
4000 Hz 72 54
8000 Hz 65 47
TOTAL 92 74
CMAT-528-2T AAF INTERNATIONAL (Ref.: 4)
Centrifugal single-inlet, medium-pressure fans with casing and straight-blade
impeller made from cast aluminium to transport dust and solids
Fan:
- Casing made from cast aluminium
-
Cast aluminium straight-blade impeller for models 324 to 531 and sheet steel for models540 to 545
Motor:
- Motors with IE-2 efficiency. except for motors with lower powers than 0.75 kW. single-
phase motors or two-speed motors
- Class F motors. with bearings. IP55 protection
- Three-phase 230/400V.-50Hz.
- Max. air temperature to transport: -20ºC.+ 120ºC
Finish:
- Anticorrosive finish in polyester resin. polymerised at 190ºC. after nanotech and
phosphate-free pre-treatment
On request:
-
Special windings for different voltages - Fan designed to transport air up to 250ºC
- ATEX certification. Category 2
CHARACTERISTIC CURVE AND ACOUSTICS AT 1.2KG/M³
Design Point
Q (m³/h) 610
Ps (Pa) 1100
Acoustics: Inlet, 3 (m), 1 plane
Service Point (SP)
TECHNICAL CHARACTERISTICS
Remarks Exclude. Transport materials
13/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 16/26
MOTOR DATA
Rated Mechanical Power (kW) 0.75
Hz/phases 50/3
Motor (rpm) 2770
Poles 2
Max. current (A) 380-415 V Y 1.60Max. current (A) 220-240 V D 2.78
Motor protection IP55
Motor frame size 71
Data can change, please check motor plate
AVAILABLE ACCESSORIES
INT C2V RM AR RFT/RFM AET RPA-18 B-125 ACE-125
It must be checked that the accessory is suitable for the fan model
14/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 17/26
DIMENSIONS
A A1 B C C1 C2 øD ød ød1 ød2 E H H1 øI
401 395 488 337 304 48 135 190 162 M6 178 288 177 190
øK øk øO øO1 V v X x1 Y
130 160 11 13 230 180 140 100 20
Dimensions without explicitly defined units are shown in millimeters (mm)
15/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 18/26
Q (m³/h) 455.15
Ps (Pa) 1050.70
Pd (Pa) 157.64
Pt (Pa) 1208.34
Impeller (rpm) 2830
Max. Temp. (ºC) 120
Outlet air speed (m/s) 16.21
Airflow maximum (m³/h) 900
Speed (rpm) 2830
Approx. weight (kg) 13.40
Band Lw dB(A) Lp dB(A)
63 Hz 47 29
125 Hz 61 43
250 Hz 84 66
500 Hz 90 72
1000 Hz 82 64
2000 Hz 75 57
4000 Hz 67 49
8000 Hz 61 43
TOTAL 92 74
CMAT-527-2T AAF INTERNATIONAL (Ref.: 5)
Centrifugal single-inlet, medium-pressure fans with casing and straight-blade
impeller made from cast aluminium to transport dust and solids
Fan:
- Casing made from cast aluminium
-
Cast aluminium straight-blade impeller for models 324 to 531 and sheet steel for models540 to 545
Motor:
- Motors with IE-2 efficiency. except for motors with lower powers than 0.75 kW. single-
phase motors or two-speed motors
- Class F motors. with bearings. IP55 protection
- Three-phase 230/400V.-50Hz.
- Max. air temperature to transport: -20ºC.+ 120ºC
Finish:
- Anticorrosive finish in polyester resin. polymerised at 190ºC. after nanotech and
phosphate-free pre-treatment
On request:
-
Special windings for different voltages - Fan designed to transport air up to 250ºC
- ATEX certification. Category 2
CHARACTERISTIC CURVE AND ACOUSTICS AT 1.2KG/M³
Design Point
Q (m³/h) 455
Ps (Pa) 1050
Acoustics: Inlet, 3 (m), 1 plane
Service Point (SP)
TECHNICAL CHARACTERISTICS
Remarks Exclude. Transport materials
16/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 19/26
MOTOR DATA
Rated Mechanical Power (kW) 0.37
Hz/phases 50/3
Motor (rpm) 2710
Poles 2
Max. current (A) 380-415 V Y 1.11Max. current (A) 220-240 V D 1.92
Motor protection IP55
Motor frame size 63
Data can change, please check motor plate
AVAILABLE ACCESSORIES
INT C2V RM AR RFT/RFM AET RPA-17 B-125 B-100 ACE-125 ACE-100
It must be checked that the accessory is suitable for the fan model
17/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 20/26
DIMENSIONS
A A1 B C C1 C2 øD ød ød1 ød2 E H H1 øI
371 361 440 295 261 42 125 170 147 M6 168 260 170 155
øK øk øO øO1 V v X x1 Y
100 129 7 13 220 170 120 80 17
Dimensions without explicitly defined units are shown in millimeters (mm)
18/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 21/26
Q (m³/h) 1191.47
Ps (Pa) 1155.26
Pd (Pa) 277.12
Pt (Pa) 1432.38
Impeller (rpm) 2850
Max. Temp. (ºC) 120
Outlet air speed (m/s) 21.49
Airflow maximum (m³/h) 1800
Speed (rpm) 2850
Approx. weight (kg) 24
Band Lw dB(A) Lp dB(A)
63 Hz 51 33
125 Hz 67 49
250 Hz 90 72
500 Hz 92 74
1000 Hz 89 71
2000 Hz 83 65
4000 Hz 77 59
8000 Hz 69 51
TOTAL 96 78
CMAT-531-2T AAF INTERNATIONAL (Ref.: 6)
Centrifugal single-inlet, medium-pressure fans with casing and straight-blade
impeller made from cast aluminium to transport dust and solids
Fan:
- Casing made from cast aluminium
-
Cast aluminium straight-blade impeller for models 324 to 531 and sheet steel for models540 to 545
Motor:
- Motors with IE-2 efficiency. except for motors with lower powers than 0.75 kW. single-
phase motors or two-speed motors
- Class F motors. with bearings. IP55 protection
- Three-phase 230/400V.-50Hz.
- Max. air temperature to transport: -20ºC.+ 120ºC
Finish:
- Anticorrosive finish in polyester resin. polymerised at 190ºC. after nanotech and
phosphate-free pre-treatment
On request:
-
Special windings for different voltages - Fan designed to transport air up to 250ºC
- ATEX certification. Category 2
CHARACTERISTIC CURVE AND ACOUSTICS AT 1.2KG/M³
Design Point
Q (m³/h) 1022
Ps (Pa) 850
Acoustics: Inlet, 3 (m), 1 plane
Service Point (SP)
TECHNICAL CHARACTERISTICS
Remarks Exclude. Transport materials
19/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 22/26
MOTOR DATA
Rated Mechanical Power (kW) 1.10
Hz/phases 50/3
Motor (rpm) 2860
Poles 2
Max. current (A) 380-415 V Y 2.40Max. current (A) 220-240 V D 4.20
Motor protection IP55
Motor frame size 80
Data can change, please check motor plate
AVAILABLE ACCESSORIES
INT C2V RM AR RFT/RFM AET RPA-20 B-150 ACE-150
It must be checked that the accessory is suitable for the fan model
20/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 23/26
DIMENSIONS
A A1 B C C1 C2 øD ød ød1 ød2 E H H1 øI
432 420 537 340 315 50 160 215 180 M6 189 320 200 200
øK øk øO øO1 V v X x1 Y
140 175 11 13 240 190 160 120 19
Dimensions without explicitly defined units are shown in millimeters (mm)
21/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 24/26
Q (m³/h) 449.98
Ps (Pa) 1059.29
Pd (Pa) 154.08
Pt (Pa) 1213.37
Impeller (rpm) 2830
Max. Temp. (ºC) 120
Outlet air speed (m/s) 16.02
Airflow maximum (m³/h) 900
Speed (rpm) 2830
Approx. weight (kg) 13.40
Band Lw dB(A) Lp dB(A)
63 Hz 47 29
125 Hz 61 43
250 Hz 84 66
500 Hz 90 72
1000 Hz 82 64
2000 Hz 75 57
4000 Hz 67 49
8000 Hz 61 43
TOTAL 92 74
CMAT-527-2T AAF INTERNATIONAL (Ref.: 7)
Centrifugal single-inlet, medium-pressure fans with casing and straight-blade
impeller made from cast aluminium to transport dust and solids
Fan:
- Casing made from cast aluminium
-
Cast aluminium straight-blade impeller for models 324 to 531 and sheet steel for models540 to 545
Motor:
- Motors with IE-2 efficiency. except for motors with lower powers than 0.75 kW. single-
phase motors or two-speed motors
- Class F motors. with bearings. IP55 protection
- Three-phase 230/400V.-50Hz.
- Max. air temperature to transport: -20ºC.+ 120ºC
Finish:
- Anticorrosive finish in polyester resin. polymerised at 190ºC. after nanotech and
phosphate-free pre-treatment
On request:
-
Special windings for different voltages - Fan designed to transport air up to 250ºC
- ATEX certification. Category 2
CHARACTERISTIC CURVE AND ACOUSTICS AT 1.2KG/M³
Design Point
Q (m³/h) 448
Ps (Pa) 1050
Acoustics: Inlet, 3 (m), 1 plane
Service Point (SP)
TECHNICAL CHARACTERISTICS
Remarks Exclude. Transport materials
22/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 25/26
MOTOR DATA
Rated Mechanical Power (kW) 0.37
Hz/phases 50/3
Motor (rpm) 2710
Poles 2
Max. current (A) 380-415 V Y 1.11Max. current (A) 220-240 V D 1.92
Motor protection IP55
Motor frame size 63
Data can change, please check motor plate
AVAILABLE ACCESSORIES
INT C2V RM AR RFT/RFM AET RPA-17 B-125 B-100 ACE-125 ACE-100
It must be checked that the accessory is suitable for the fan model
23/24www.sodeca.com v1.10.0.0 Data in this report can change without notice
7/24/2019 3 Catalogues
http://slidepdf.com/reader/full/3-catalogues 26/26
DIMENSIONS
A A1 B C C1 C2 øD ød ød1 ød2 E H H1 øI
371 361 440 295 261 42 125 170 147 M6 168 260 170 155
øK øk øO øO1 V v X x1 Y
100 129 7 13 220 170 120 80 17
Dimensions without explicitly defined units are shown in millimeters (mm)