3-in-1TM Flat Panel Console Model # XL-10 · 3-in-1TM Flat Panel Console Model # XL-10 This item is designed to be a 3-in-1 configuration. Please choose the option that best suits

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Whalen Furniture Mfg. Inc. Page 1 Factory No. 56-12089

3-in-1TM

Flat Panel Console Model # XL-10

This item is designed to be a 3-in-1 configuration. Please choose the option that best suits your needs. DO NOT discard any of the hardware or parts that you will not use on your set option, this will give you the opportunity to use this TV Console for different configurations in case you decide to upgrade your TV set in the future.

ADULT ASSEMBLY REQUIRED

If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number:

1-866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday

Or visit our web site 24 hours a day, 7 days a week for product assistance at

www.whalenstyle.com Or e-mail your request to [email protected]

LOT NUMBER: DATE PURCHASED: / /

mailto:[email protected]

Model # XL-10

Whalen Furniture Mfg. Inc. Page 2 Factory No. 56-12089

MANUFACTURER: Whalen Furniture CATALOG: 3-in-1TM Flat Panel Console (XL-10) DATE OF MANUFACTURE: June 2012 MADE IN CHINA

1. Please read the Assembly Instructions prior to assembling this product. 2. Remove all hardware from box and sort by size. 3. Check to see that all hardware and parts are present BEFORE assembling. 4. Ask a friend to assist you with the assembly of this furniture. 5. To avoid damage, assemble the product on a sturdy, level and protective surface. 6. Please wait until all steps are completed before tightening bolts. 7. Make sure all bolts are tightly fastened before the unit is used.

M AX I M UM REC OM M EN D E D W EI G H T LO AD S

GENER AL IN FORM ATION, T I PS and TRICKS

THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN CENTRE OF UNIT; CRT TVS, IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS OR OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.

FITS UP TO MOST 56” FLAT PANEL TVs MAXIMUM LOAD 135 lb. (61.2 kg)

FITS UP TO MOST 56” FLAT PANEL TVs WITHOUT SWIVELING BRACKET MAXIMUM LOAD 135 lb. (61.2 kg)

MAXIMUM LOAD 50 lb. (22.7 kg)

PLACE TV BEHIND STOPPER

This product is sold with Tip Restraint Hardware kit. You must install the Tipping Restraint Hardware between the wall and the TV stand to prevent any accidents or damages. When properly installed, this restraint can provide protection against the unexpected tipping of the unit due to small tremors, bumps or climbing. The restraint is only a deterrent and is not a substitute for proper adult supervision. Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.

Model # XL-10


Parts and Hardware List

Please read completely through the instructions and verify that all parts listed are present before beginning assembly.

A- TOP SHELF FRAME (1) B- MIDDLE SHELF FRAME (1)

C- BOTTOM SHELF FRAME (1) D- LONG SPINE (1) D1- SHORT SPINE (1)

E- LEFT LEG (1) F- RIGHT LEG (1) G- TOP GLASS (1)

H- GLASS SHELF (2) I- FRONT LEFT SUPPORT (1) J- FRONT RIGHT SUPPORT (1)

K- BACK LEFT SUPPORT (1) L- BACK RIGHT SUPPORT (1) M- SWIVELING BRACKET (1)

N- XYZ MOUNTING FRAME (1) O- MONITOR BRACKET (L/R) (2) P- CABLE CONTROL (2)

OR OL

Model # XL-10


Parts and Hardware Master List

(1) SUCTION CUP (2) 3/4” BOLT (3) 1-1/4” BOLT (4) HEX NUT

(12+1 extra) (44+2 extra) (9+1 extra) (4+1 extra)

(5) LOCK WASHER (6) FLAT WASHER (7) LAG BOLT WASHER (8) 2-1/2” LAG BOLT

(49+2 extra) (53+2 extra) (6) (6)

(9) CONCRETE ANCHOR (10) ACRYLIC STOPPER (11) FLOOR LEVELER TOUCH-UP PEN (6) (1) (1) (1)

OPEN WRENCH M4 ALLEN WRENCH 3/16” ALLEN WRENCH TIPPING RESTRAINT HARDWARE KIT (1)

(1) (2) (1) (Inside Plastic Bag)

TV Mounting Kit

M4 x 12 BOLT (4) M4 x 30 BOLT (4) M5 x 12 BOLT (4) M5 x 30 BOLT (4)

M6 x 12 BOLT (4) M6 x 35 BOLT (4) M8 x 16 BOLT (4) M8 x 40 BOLT (4)

M4 LOCK WASHER (4) M5 LOCK WASHER (4) M6 LOCK WASHER (4) M8 LOCK WASHER (4)

LARGE SPACER (4) SMALL SPACER (4) M4/M5 FLAT WASHER (8) M6/M8 FLAT WASHER (4)

Tools required: Allen Wrench, Open Wrench (provided) and Phillips screwdriver (not provided).

Model # XL-10


3

5

D/D1

A/B/C

D

D1

UP

UP

C11

Assembly Instructions

Note: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled, go back and fully tighten all bolts. This will make it easier during assembly of unit.

1. Unpack the unit and confirm that you have all the hardware and parts required. 2. Choose the option suits your needs. Locate LONG SPINE (D) or SHORT SPINE (D1) and

set back face down on a scratch free surface as shown above. 3. Align and attach three SHELF FRAMES (A, B and C) to the SPINE using 1-1/4” BOLTS (3)

with LOCK WASHERS (5) and FLAT WASHERS (6) through the pre-drilled holes on back rail into the threaded inserts included in the SPINE. Ensure the end bracket is positioned with two holes facing the floor.

4. Screw FLOOR LEVELER (11) to the center support of the BOTTOM SHELF FRAME (C) by rotating clockwise.

1-1/4” BOLT

(6 used in this step)

③

LOCK WASHER


⑤

FLAT WASHER


⑥

FLOOR LEVELER


⑪

Model # XL-10



5. Stand the unit upright.

6. Align and attach LEFT LEG (E) to three SHELF FRAMES (A, B and C) by inserting the 3/4” BOLTS (2) with WASHERS (5 and 6) through the end bracket holes of SHELF FRAMES into the threaded inserts on the LEFT LEG. Make sure the top surface is flush with TOP SHELF FRAME (A). DO NOT tighten the bolts.

7. Repeat last step with RIGHT LEG (F). Make sure the gaps and offsets between the wooden front rail of TOP SHELF FRAME (A) and the LEGS (E and F) are equal. Loosen the bolts on the end brackets and wooden front rail and adjust if necessary.

D

E

F

D1

E

F

E/F

2

6

FLAT WASHER


⑥

LOCK WASHER


⑤

3/4” BOLT


②

Model # XL-10



8. For a stable structure, align and attach FRONT LEFT SUPPORT (I) and FRONT RIGHT SUPPORT (J) in place to connect the TOP SHELF FRAME (A) with LEFT and RIGHT LEGS (E and F) using 3/4” BOLTS (2) with WASHERS (5 and 6) through the end bracket holes, as shown above.

9. Align and attach BACK LEFT SUPPORT (K) and BACK RIGHT SUPPORT (L) to the TOP SHELF FRAME (A) and SPINE using the 3/4” BOLTS (2) and WASHERS (5 and 6).

FLAT WASHER


⑥

LOCK WASHER


⑤

3/4” BOLT


②

D

E

6 5

I

A

A

D/D1

K L

625

E

F

D1

I

JL

I

JL

E

F

Model # XL-10



10. Go back and tighten all BOLTS with the ALLEN WRENCH provided.

11. In case of uneven floor, FLOOR LEVELERS are provided at the bottom of both LEGS (E and F) and the SUPPORT LEG on BOTTOM SHELF FRAME (C). Simply tilt the unit back and raise or lower FLOOR LEVELER by hand to correct tilting as shown above.

If you choose Table-top configuration, continue to STEP 12.

If mounting TV with the Swinging Floater,

skip ahead to PAGE 13.

EC/E/F

E

F

F

Model # XL-10


E

F

D1

P

2

D1

Assembly Instructions for Table-top Console

12. Attach 2 CABLE CONTROLS (P) onto the backside of SHORT SPINE (D1) with the 3/4” BOLTS (2). Tighten the BOLTS with the ALLEN WRENCH provided.

13. The CABLE CONTROLS (P) enable you to shorten, separate and route cables and cords. Using the CABLE CONTROLS you can create a system for routing cables through channels, between components and to power sources without tangled mess or annoying signal interference.

3/4” BOLT


②

Model # XL-10


B/C

1

H

A

B

CE

G

H

H

35

A

G


14. Put the SUCTION CUPS (1) firmly into top holes of the MIDDLE SHELF FRAME (B) and BOTTOM SHELF FRAME (C) as shown. Tip: If a SUCTION CUP resists insertion, try pressing down on the middle of the cup with the ALLEN WRENCH while twisting it clockwise into the hole.

15. Place GLASS SHELVES (H) in place starting from the BOTTOM GLASS SHELF as shown above. Make sure the glass is properly centered. Push each GLASS all the way back against the SPINE. Also, be sure to press down evenly and firmly each GLASS onto the SUCTION CUPS to make sure they securely rest onto the SUCTION CUPS.

16. Set the TOP GLASS (G) onto place so that the bottom glass risers overlap the pre-drilled holes on the TOP SHELF FRAME (A) properly. Insert three 1-1/4” BOLTS (3) with WASHERS (5 and 6) through the pre-drilled holes on TOP SHELF FRAME (A) and screw into the glass risers.

1-1/4” BOLT


③

LOCK WASHER


⑤

FLAT WASHER


⑥

SUCTION CUP


①

Model # XL-10



NOTE: You must install the Acrylic TV Stopper to prevent TV from tipping when placing your flat panel television directly on the table-top console.

17. Remove the tape of ACRYLIC STOPPER (10) and place it on the cut-out of the warning

label on the front of TOP GLASS (G). Make sure it is aligned before applying pressure.

18. Remove the warning label for ACRYLIC STOPPER carefully.

G

G

ACRYLIC STOPPER (1 used in this step)

⑩

Model # XL-10


Assembly Instructions for Table-top

Tools required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.

19. Position the assembled Table-top in your desired location against a wall. Now follow the instructions printed on the plastic bag containing the TIPPING RESTRAINT HARDWARE to mount the tipping restraint to the SPINE and the wall. NOTE: YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO THE WALL, TO PREVENT ACCIDENTS AND/OR INJURIES.

20. The Table-top is ready for use now. Be sure to position your Flat Panel TV in center of the

console.

NOTE: For Tilting Wall Mount, proceed to PAGE #20.

Model # XL-10


D

M

6

UP

5

C

D

E

F

M

M

D

21. Align and attach the SWIVELING BRACKET (M) to the top of LONG SPINE (D) with six 3/4” BOLTS (2) and WASHERS (5 and 6). Make sure the pivoting bolt head is up. Tighten the bolts with enclosed M4 Allen Wrench.

NOTE: The LONG SPINE can provide four height options for your TV set. Refer to your TV size, adjust the Swiveling Bracket at your desired height to offer optimum viewing.

Asse mbl y Ins t ruc t ions for Opt ion :

F loa t ing Sw i ve l Mount

FLAT WASHER


⑥

LOCK WASHER


⑤

3/4” BOLT


②

Model # XL-10


M

M

N

5

5

6

CE

F

D

N

Assembly Instructions for Floating Swivel Mount

22. Hold the flat side of XYZ MOUNTING FRAME (N) onto the SWIVELING BRACKET (M) ensuring the recessed 2 holes on the MOUNTING FRAME bottom. Align and attach by threading four 3/4” BOLTS (2) with FLAT WASHERS (6) through the metal plate on XYZ MOUNTING FRAME and the SWIVELING BRACKET, at the other side of SWIVELING BRACKET fit the other FLAT WASHERS (6) and LOCK WASHERS (5) onto the BOLTS, and then secure with HEX NUTS (4). Securely tighten with OPEN WRENCH and ALLEN WRENCH provided.

FLAT WASHER


⑥

LOCK WASHER


⑤

3/4” BOLT


②

HEX NUT


④

Model # XL-10


Mounting Monitor Brackets to a Television with a Flat Back

NOTE: For televisions with a curved back or recessed back proceed directly to next page.

23. Determine the correct diameter of the bolt your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If you are unable to find the correct bolt consult a local hardware store.

24. Follow the appropriate diagram above to attach MONITOR BRACKETS (OL/OR) to the back of your TV with selected fasteners. Make sure the MONITOR BRACKETS are centered and level with each other. Secure the bolts with a PHILLIPS SCREWDRIVER. DO NOT over tighten the bolts.

NOTE: Lean the TV up against a wall or other solid surface when attaching with the Monitor Brackets. DO NOT place the TV face down on the glass this may cause permanent damage.

Model # XL-10


Mounting Monitor Brackets to a Television with a Curved/Recess Back

25. Determine the correct diameter of the bolt your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If you are unable to find the correct bolt consult a local hardware store.

26. Follow the appropriate diagram above to attach MONITOR BRACKETS (OL/OR) to the back

of your TV with selected fasteners. Make sure the MONITOR BRACKETS are vertically centered and level with each other. Secure the bolts with a PHILLIPS SCREWDRIVER. DO NOT over tighten the bolts.

Model # XL-10


D

C

E

F

N

OR

OL

NN

N


MAKE SURE ALL BOLTS ARE TIGHT AND SPINE IS AT A 90 DEGREE ANGLE AND USING A QUALITY LEVEL TO VERIFY THE MOUNTING FRAME IS LEVEL PRIOR TO INSTALLATION OF TV.

27. Once the MONITOR BRACKETS (OL/OR) are attached onto the back of television, ask for

assistance to lift the television up to hang the MONITOR BRACKETS onto the XYZ MOUNTING FRAME (N). Set the hooks on MONITOR BRACKETS over the MOUNTING FRAME then lower them onto the bars of MOUNTING FRAME. NOTE: Loosen the LOCK BOLT pre-attached on the MONITOR BRACKETS to ensure an easy fit at the bottom hooks.

28. Center the television and tighten both LOCK BOLTS with a long PHILLIPS SCREWDRIVER

until they hit underside of XYZ MOUNTING FRAME (N) to secure it in place.

Model # XL-10



29. The MONITOR BRACKETS (OL/OR) can tilt up to 11˚ downward and 5˚ upward, depending on your optimum viewing position. Have your assistant hold the TV steady before you start to adjust the tilt. Simply reach behind the TV and turn the both Tilt Adjustment Knobs with enclosed 3/16” ALLEN WRENCH to adjust your TV to provide optimum viewing and minimize glare. When the TV is in its intended position, tighten both lock bolts to secure it in place.

Note: If you need to remove the TV, make sure both Lock Bolts are disengaged fully.

Model # XL-10



Tools required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.

30. Repeat the same process to attach the CABLE CONTROLS (P) and install the TOP GLASS (G) and GLASS SHELVES (H) in place.

31. Carefully move the console and position in your desired location against a wall. Now follow the instructions printed on the plastic bag containing TIPPING RESTRAINT HARDWARE KIT to mount the tipping restraint to the SPINE and the wall.

NOTE: You must install the Tipping Restraint Hardware with the unit in use to prevent any accidents or damage to the unit.

32. You can enjoy your home entertainment center now. Swivel left-or-right for optimum viewing control.

Model # XL-10


Assembly Instructions for Universal Wall Mount Installing XYZ Mounting Frame onto WOODEN STUD WALL

NOTE: If you are mounting your TV onto brick, solid concrete or concrete block, skip this section. This assembly requires an electric drill, level and stud finder (not included).

33. Using a stud finder, locate the edges of the wood studs. Find the center line of each stud and draw a vertical reference line on the wall over each one. Place the XYZ MOUNTING FRAME (N) level against the wall where you intend to mount the TV. Using the MOUNTING FRAME (N) as a template, mark 4 drill points (2 on top, 2 on bottom) with a pencil on the vertical reference lines you just drew.

34. With an electric drill (not included) drill 3/16 inch diameter holes to at least 2½ inch deep on the four drill points. While holding the Bracket Plate in place, loosely screw in the Lag Bolts (8).

35. Secure the XYZ MOUNTING FRAME (N) to wall with LAG BOLTS (8) and WASHERS (7) at the drill points. Tighten bolts firmly, but be careful not to over-tighten.

The following steps are only for those who wish to mount their TV directly to the wall. If you have already mounted your TV to the Swinging Floater or plan to display your TV on the top surface of the stand, disregard the following steps.

Do not over-tighten the Lag Bolts. Tighten Lag Bolts only until the Lag Bolt Washer is pulled firmly against the metal plate of Mounting Frame. If there is a layer of drywall or other material, this drywall or other material may not exceed 5/8 inch in thickness. Failure to heed this caution may result property damage and/or personal injury.

2.50" (63 mm)

?0

.20

" (5

mm

)

Model # XL-10


Assembly Instruction for installing XYZ Mounting Frame onto BRICK, SOLID CONCRETE OR CONCRETE BLOCK

NOTE: If you are mounting your TV to a wall with wooden studs, skip this section. This assembly requires an electric drill and level (not included).

36. Begin by placing the XYZ MOUNTING FRAME (N) level against the wall where you intend to mount the TV. Using the MOUNTING FRAME as a template, mark 6 drill points with a pencil.

37. With an electric drill (not included) on its low setting, drill 7/16 inch diameter holes to at least 2½ inch deep. Insert CONCRETE ANCHORS (9) into pre-drilled holes so that they are flush with the wall.

38. Place the XYZ MOUNTING FRAME (N) level in the desired position against the wall. Secure the MOUNTING FRAME (N) to wall with six LAG BOLTS (8) and WASHERS (7) at the drill points. Tighten bolts firmly, but be careful not to over-tighten.

Concrete Anchors should only be used for masonry mounting. NEVER use the wall anchors to mount the unit to drywall.

Maximum weight 135 lb. (61.2 kg)

Model # XL-10



39. Once the MONITOR BRACKETS (OL/OR) are attached onto the back of television, ask for assistance to lift the television up to attach the Monitor Brackets onto the XYZ MOUNTING FRAME (N). Set the hooks on Monitor Brackets over the Mounting Frame then lower them onto the bars of Mounting Frame. Loosen the Lock Bolt pre-attached on the Monitor Brackets to ensure an easy fit at the bottom hooks. Proceed to center the television.

40. If you want to adjust the tilt, ask for help from your friends to hold the TV steady before you start to adjust. Simply turn the both Tilt Adjustment Knobs on Monitor Brackets (OL/OR) with 3/16” Allen Wrench to adjust your TV to provide optimum viewing and minimize glare. When the TV is in its intended position, tighten both Lock bolts with a long Phillips Screwdriver until they hit underside of XYZ Mounting Frame (N) to ensure your TV is safe and secure on the wall.

41. Place assembled console under your TV set. Finally, connect the A/V and power cables to your TV. You are now ready to enjoy your wall-mounted Flat Panel TV.

Model # XL-10


Care and Maintenance

Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an

inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently.

Avoid rubbing. Always use protective pads under hot dishes and plates. Heat can cause chemical changes

that may create spotting within the furniture finish. Stains or marks from crayons or ink markers will be difficult to remove. In the event that your furniture is stained or otherwise damaged during use, we recommend

that you call a professional to repair your furniture. Check bolts/screws periodically and tighten them if necessary.

Further advice about furniture care

It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from direct sunlight as sun may damage the finish. Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages.

A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during assembly or shipping.

We hope you enjoy your purchase for many years. Thank you for choosing Whalen Furniture!

QUALITY GUARANTEE

We are confident that you will be delighted with your Whalen Furniture purchase. Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture. This warranty gives you specific legal rights and you may also have other rights which vary from State to State.

Customer Service: 1-866-942-5362

8:30 a.m. - 4:30 p.m., PST, Monday to Friday

www.whalenstyle.com

http://www.whalenstyle.com/

SI R

EQ

UIE

RE

OR

DE

NA

R P

AR

TE

S U

TIL

IZA

R L

A L

IST

A IN

FE

RIO

R

Consola

para

Tele

vis

ión 3

en 1

TM (X

L-1

0)

2

356 4

99

8

10

11

12

13

14

15

16

17

21

722

18

19

20

24

25

26

27

28

29

30

31

32

33

34

35

36

37

23

*XL-1

0-1

-LS

Poste

Larg

o*X

L-1

0-2

1-R

MB

Soporte

de M

onito

r Dere

cho

*XL-1

0-2

-SS

Poste

Corto

*XL-1

0-2

2-O

PG

Oja

l Ovala

do

*XL-1

0-3

-TS

FR

epis

a S

uperio

r*X

L-1

0-2

3-T

RH

KJuego S

uje

tador

*XL-1

0-4

-WF

RR

iel F

ronta

l de M

adera

*XL-1

0-2

4-S

CV

ento

sa

*XL-1

0-5

-MS

FR

epis

a In

term

edia

*XL-1

0-2

5-3

/4B

Torn

illo d

e 3

/4”

*XL-1

0-6

-BS

FR

epis

a In

ferio

r*X

L-1

0-2

6-1

1/4

BT

orn

illo d

e 1

-1/4

”

*XL-1

0-7

-CC

Guía

para

Cable

*XL-1

0-2

7-H

NT

uerc

a

*XL-1

0-8

-TG

Vid

rio S

uperio

r*X

L-1

0-2

8-L

WA

randela

de P

resió

n

*XL-1

0-9

-GS

Entre

paño d

e V

idrio

*XL-1

0-2

9-F

WA

randela

Pla

na

*XL-1

0-1

0-L

LP

ata

Izquie

rda

*XL-1

0-3

0-L

BW

Ara

ndela

Gra

nde

*XL-1

0-1

1-R

LP

ata

Dere

cha

*XL-1

0-3

1-2

1/2

LB

Torn

illo d

e 2

-1/2

”

*XL-1

0-1

2-F

LS

Soporte

Fro

nta

l Izquie

rdo

*XL-1

0-3

2-C

AT

aquete

*XL-1

0-1

3-F

RS

Soporte

Fro

nta

l Dere

cho

*XL-1

0-3

3-F

LN

ivela

dor

*XL-1

0-1

4-B

LS

Soporte

Poste

rior Iz

quie

rdo

*XL-1

0-3

4-O

WLla

ve E

spañola

*XL-1

0-1

5-B

RS

Soporte

Poste

rior D

ere

cho

*XL-1

0-3

5-T

UP

Plu

món

*XL-1

0-1

6-S

BS

oporte

Gira

torio

*XL-1

0-3

6-M

4A

WM

4 L

lave A

llen

*XL-1

0-1

7-M

FM

arc

o d

e M

onta

je X

YZ

*XL-1

0-3

7-3

/16A

W3/1

6" L

lave A

llen

*XL-1

0-1

8-L

BT

orn

illo C

andado

*XL-1

0-T

VM

KJuego d

e M

onta

je T

V

*XL

10

19

TA

KM

il

dj

td

Ili

ió*X

L10

CH

C

2

356 4

99

8

10

11

12

13

14

15

16

17

21

722

18

19

20

24

25

26

27

28

29

30

31

32

33

34

35

36

37

23

*XL-1

0-1

9-T

AK

Maniv

ela

de a

juste

de In

clin

ació

n*X

L-1

0-C

HH

erra

je C

om

ple

to

*XL-1

0-2

0-L

MB

Soporte

de M

onito

r Izquie

rdo

2

356 4

99

8

10

11

12

13

14

15

16

17

21

722

18

19

20

24

25

26

27

28

29

30

31

32

33

34

35

36

37

23

Documents

3-in-1TM Flat Panel Console Model # XL-10 · 3-in-1TM Flat Panel Console Model # XL-10 This item is designed to be a 3-in-1 configuration. Please choose the option that best suits