33031235-0108-11 Chevy Cruze Super Fine Mesh

7/29/2019 33031235-0108-11 Chevy Cruze Super Fine Mesh

1/5

IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE !Copyright 2010 by E&G Classics, Inc. All right reserved. The reproduction or utilization of this work in any form or any electronic, mechanical, or other means, no known or hereafter invented,

including xerography, photocopying, and recording, and in any information storage retrieval system is forbidden without written permission of owners.

Part #: Complete 1235-0108-11 / Black Ice Part #1235-B108-11Upper Part #1235-010U-11 / Lower Part #1235-010L-11

Notes to the Technician/Installer:E&G is proud to present this package to you and reminds you that for technical information, contact technical assistance at 410-381-4900. Do not attempt the installation

of any E&G product without first reading the detailed instructions. E&G Classics will not warrant damaged parts or the vehicle due to altered installation instructions.

A 31 H1 R

1. Open the hood and remove the four (4) factory push pins securing

the bumper cover and grille assembly to the radiator support

panel.

2. Loosen the two (2) 10mm hex bolts at the upper outer corners but

to not completely remove them at this time.

3. Raise the vehicle and remove the six (6) Torx T-20 screws from

the wheel wells (three per side).

Copyright 2010 by E&G Classics, Inc. Visit us online today at www.egclassics.com

2011 Chevrolet Cruze Mesh Grille

TOOLS REQUIREDFlat blade screwdriver, 9 & 10mm socket and socket wrench, Torx T-20 bit, automotive grade masking tape,

hammer and small flat punch.

Upper and Lower Overlay

4. Remove eleven (11) Torx T-20 screws from across the bottom of

the bumper cover.

5. Apply several layers of masking tape to the front fender and

bumper cover where they meet.

12 2

3

4 5


2/5

6. Use several quick tugs to pull the top edge of the bumper cover

free from the mounting bracket.

7. Once the edges are loose, continue pulling the bumper cover to

release it from the mounting channel under the headlights.

8. Reach behind the bumper cover and remove the side marker

lamp bulbs (one each side) and remove the electrical plug on the1

bumper mounted sensor on the divers side.

9. Remove the 10mm hex bolts loosened in step 2 and pull the

bumper cover straight off to remove it.

10. Place the bumper cover on a clean work surface for mesh grille

installation.


11. If the vehicle has a front license plate bracket, remove it to

install the lower mesh grille. Use a 3/16 drill bit to drill through

the aluminum rivet heads and remove the bracket.

10. Apply masking tape to the upper and center chrome surrounds

and 1/16 forward of the step in the lower grille opening.

6 7

8 9

11

12


3/5

11. Use a scotch brite pad or fine sandpaper to scuff the paint. Apply

flat or semi-gloss black paint to the factory lower grille opening

as shown.

12. Once the paint has dried, align the pre-assembled lower mesh

grille through the lower factory opening. Install the supplied

mounting brackets and #8-32 ESNA half nuts onto the four long

studs to secure the lower grille.

13. Use a disc grinder to remove the melted over plastic tabs retain

ing the block off plates from the center grille and remove the

plates.

14. Use a 5/32 drill bit to drill through the upper outer factory grille

where shown, each side.


15. Use a 5/32 drill bit to drill through the upper factory grille where

shown, each side.

16. Align the upper mesh section into place, then pass one of the

mesh pins through the mesh above the holes drilled in Steps 14

and 15. Press the pins firmly into place then fold the pins over to

secure the mesh section into place.

17. Remove any masking tape that could get caught behind the

mesh at this time (not shown).

12

14

15

16


4/5

18. Use a small block of wood to press firmly against the pin. 19. With the pin firmly pressed against the mesh, use a punch and a

hammer to fold over the portion of the pins protruding through

the factory grille. This will further tighten the mesh down over the

factory grille.

20. If the mesh is not tight in any of the corners, drill additional 5/32

holes where needed and install the mesh pins.

21 Measure in from the edge 11/16 and use masking tape to form

a cutting line for the factory front license plate bracket.


22. Trim off the excess plastic, remove and grind flush the lower

spacer as shown.

23. Reinstall the front license plate bracket using the supplied self

tapping bolts.

19

2011/16

23


5/5

E&G Classics Warranty Information:E&G Classics, Inc. warrants its chrome parts and products to be free from defects in ma-

terial, workmanship or finish for Thirty-Six (36) months from the date of shipment by E&G.

This warranty is limited to the repair or replacement, at E&G Classics option, of the defec-

tive part or product.Full E&G Classics warranty information is available online @

www.egclassics.com. Just click on the product warranty icon.

For E&G Classic Product Returns:Please contact the authorized E&G Classics Dealer where you purchased our prod-

uct from in regards to any workmanship or warranty claims. All items returned to

E&G Classics must have a return authorization number issued by us for inspection

or a defective product and or warranty issue. All merchandise sent back to E&G

Classics without proper paperwork or authorization will be rejected and returned.

Quantity: Description: Part Number:

1 Upper Upper Mesh Section 1235-053A-11

1 Upper Lower Mesh Section 1235-053B-11

1 Lower Mesh Grille Assembly *****************

1 Installation Hardware Kit 1235-1902-11

14 Powder Coated Mesh Pins 1235-0156-11

4 Lower grille Mounting Brackets 1125-0159-11

4 #8-32 ESNA Half Nuts 1999-0065-00

4 Self Tapping Hex Head Screws 1999-0359-00

Part #1235-0108-11


1 Upper Upper Mesh Section 1235-053A-11BI

1 Upper Lower Mesh Section 1235-053B-11BI





4 #8-32 ESNA Half Nuts 1999-0065-00


Black Ice Part #1235-B108-11


1 Upper Upper Mesh Section 1235-053A-11

1 Upper Lower Mesh Section 1235-053B-11



Upper Part #1235-010U-11





4 #8-32 ESNA Half Nuts 1999-0065-00


Lower Part #1235-010L-11

Documents

33031235-0108-11 Chevy Cruze Super Fine Mesh