38333780 CCNA Exploration Network Fundamentals Ver4 0 Enetwork Final Exam v1 92 With Feedback Corrections

8/6/2019 38333780 CCNA Exploration Network Fundamentals Ver4 0 Enetwork Final Exam v1 92 With Feedback Corrections

1/29

Assessment Systemkip to Exam Instructions | Skip to Begin Assessment

Assessment Introduction - ENetwork Final Exam - CCNA Exploration: NetworkFundamentals (Version 4.0)

Time Remaining: 02:00:00

Assessment Instructions

Cisco Networking Academy content is copyrighted and the unauthorized posting, distribution or

sharing of this exam content is prohibited.

Assessment IntroductionThis final exam will cover material from all of ENetwork: Network Fundamentals Version 4.0 of thecurriculum.

This exam will be scored using the Weighted Model where each MCSA (Multiple-Choice Single-Answer) isworth two points and each MCMA (Multiple-Choice Multiple-Answer) is worth one point for each correctoption. If more options are selected than required, the student will receive a score of zero.

Mouse Roll Over InstructionsPlease be aware that usage of a mouse with a scroll wheel may change the selected answers during anassessment. If the pointer is focused over the options in a question, then it is possible that using the scrollwheel could change the intended answer. Due to this problem, the use of the scroll wheel while takingassessments is not advised. However, if the scroll wheel is used, please be sure to check your answersprior to submitting your exam.

Personalized FeedbackOnce the exam is submitted, a personalized feedback report will be available to you on the Exam ResultsPage. This report highlights topics that may be helpful for review or study based on your performance onhis exam, but does not make up a complete list of possible weak areas. Please remember that the itemson your exam may not have addressed all of the material covered in the curriculum.

2010, Cisco Systems, Inc.

Form Information:There will be 50 items on this exam.

Begin Assessment

Once the Begin Assessment button is clicked, the button will disappear while the assessment is loadingand the clock will start for this assessment.

l contents copyright 1992-2009 Cisco Systems, Inc. Privacy Statement and Trademarks

co Networking Academy http://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtml

1 15/01/2010 22:11


2/29

Assessment Systemkip to Time Left | Skip to Navigation | Skip to Assessment Items

Take Assessment - ENetwork Final Exam - CCNA Exploration: Network FundamentalsVersion 4.0)

Time Remaining:00:31:46

Showing 1 of 4 Next> Page: GO


3/29

Which subnet mask will allow 2040 hosts per subnet on the IP network 10.0.0.0?255.255.0.0255.255.254.0

255.255.252.0255.255.248.0255.255.240.0255.255.255.128

Refer to the exhibit. A PC is communicating with another PC on a remote network. The two networksare connected by three routers. Which action will help to identify the path between the hosts?

Use the ipconfig command at the host.

Use the ipconfig/all command at the destination.

Use the tracert command at the host.


6 15/01/2010 23:42


4/29

Use the ping command at the destination.

Refer to the exhibit. An administrator made several changes to the configuration of the router but did

not accomplish the desired result. To undo the changes the reload command was used. What will

happen if the administrator answers yes to the prompt?The changes will be lost and the configuration file in RAM will be loaded.The changes will be saved and the configuration file in RAM will be loaded.The changes will be lost and the configuration file in NVRAM will be loaded.The changes will be saved and the configuration file in NVRAM will be loaded.

Refer to the exhibit. What two facts can be determined about the exhibited topology? (Choose two.)A single broadcast domain is present

Two logical address ranges are required.

Three broadcast domains are shown.

Four networks are needed.

Five collision domains exist.

Which option shows how a router will route packets to a remote network?


6 15/01/2010 23:42


5/29

What is true regarding network layer addressing? (Choose three.)

uses a flat structure

prevent broadcastsheirarchical

uniquely identifies each host

48 bits in length

contains a network portion

A network has grown too large for technicians to configure network addresses and hosts files forname resolution. Which two application layer services should be added to the server to allow theseneeds to be satisfied dynamically? (Choose two.)

DNS

FTP

DHCP

HTTP

SMTP

A user sees the command prompt: Router(config-if)# . What task can be performed at this mode?Reload the device.Perform basic tests.Configure individual interfaces.Configure individual terminal lines.

0 A user enters http://www.cisco.com/web1.htm in the address line of a browser. Which statement istrue about this transaction?

The "http" portion indicates the protocol that is being used.The "web1.htm" portion is the specific service name.

The retrieved web page will be displayed in URL code.The "www.cisco.com" is the name of the web page file that is called.

1 What is the Cisco IOS?


6 15/01/2010 23:42


6/29

system software for Cisco devicesRead Only Memory in Cisco devicesnon-volatile storage for device configurationsan initial operating system that is used for boot functions

2

Refer to the exhibit. Communication for hosts X and Y is restricted to the local network. What is thereason for this?

Host X is assigned a network address.Host Y is assigned a multicast address.Host X and host Y belong to different networks.The gateway addresses are broadcast addresses.

3 Which OSI layer offers ordered data reconstruction services?application layernetwork layerpresentation layersession layertransport layer

4

Refer to the exhibit. A student has wired each end of a CAT 5e cable as shown. What is the result?(Choose two.)

The cable is unusable and must be rewired.

The cable is suitable for use as a rollover cable.

The cable is suitable for use as a Fast Ethernet crossover.


6 15/01/2010 23:42


7/29

The cable is suitable for use as a Gigabit Ethernet straight-through.

The cable is suitable for use between two 100 Mbps Auto-MDIX capable switches.

5 Which information is used by the router to determine the path between the source and destinationhosts?

the host portion of the IP addressthe network portion of the IP addresshost default gateway addressthe MAC address



8/29






9/29

7

Refer to the exhibit. The diagram represents the process of sending e-mail between clients. Whichlist correctly identifies the component or protocol used at each numbered stage of the diagram?

1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA

8

Refer to the exhibit. A network technician is trying to determine the correct IP address configurationfor Host A. What is a valid configuration for Host A?IP address: 192.168.100.19; Subnet Mask: 255.255.255.248; Default Gateway: 192.16.1.2IP address: 192.168.100.20; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.17IP address: 192.168.100.21; Subnet Mask: 255.255.255.248; Default Gateway: 192.168.100.18IP address: 192.168.100.22; Subnet Mask: 255.255.255.240; Default Gateway: 10.1.1.5IP address: 192.168.100.30; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.1.1IP address: 192.168.100.31; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.18

9


9 15/01/2010 23:4


10/29

Refer to the exhibit. An employee wants to access the organization intranet from home. Whichintermediary device should be used to connect the organization intranet to the Internet to enable thisaccess?

hubswitch

routerwireless access point

0 Which physical component is used to access and perform the initial configuration on a newunconfigured router?


9 15/01/2010 23:4


11/29

1 Which table accurately associates the RFC 1918 private IP addresses with the correct network mask?

2


9 15/01/2010 23:4


12/29

Refer to the exhibit. A technician is working on a network problem that requires verification of therouter LAN interface. What address should be pinged from this host to confirm that the routerinterface is operational?

127.0.0.1192.168.64.196192.168.254.1192.168.254.9192.168.254.254

3 Which exhibit shows the interface that is configured by the command, router(config)# interface serial

0/0/1?


9 15/01/2010 23:4


13/29

4

Refer to the exhibit. Host B attempts to establish a TCP/IP session with host C. During this attempt, aframe was captured at the FastEthernet interface fa0/1 of the San Francisco router. The packet insidethe captured frame has the source IP address 10.10.1.2, and the destination IP address is


9 15/01/2010 23:4


14/29

10.31.1.20. What is the destination MAC address of the frame at the time of capture?0060.7320.D6320060.7320.D6310040.8517.44C30009.B2E4.EE030010.C2B4.3421

5 Which two functions of the OSI model occur at layer two? (Choose two.)

physical addressing

encoding

routingcabling

media access control

6 A network administrator subnets the network 192.168.1.0/24 into four subnets. Which option correctlyaddresses Router1 and host A into the second subnet created?

7 Which option shows the PDU that contains the Layer 3 source and destination addressing for apacket?


9 15/01/2010 23:4


15/29

8

Refer to the exhibit. A router, whose table is shown, receives a packet that is destined for192.168.1.4. How will router treat the packet?

The packet will be dropped.The packet will be forwarded via FastEthernet 0/0.The packet will be forwarded to the destination host.The packet will be forwarded to the 192.168.1.3 next-hop address.


9 15/01/2010 23:4


16/29

9 Which OSI layer manages data segments?application layerpresentation layersession layertransport layer

0

Refer to the exhibit. RouterB is configured properly. The Ethernet interface Fa0/0 of RouterA isconfigured with the use of the commands that are shown. However, a ping from the Fa0/0 interface ofRouterA to the Fa0/0 interface of RouterB is unsuccessful. What action should be taken on RouterAto solve this problem?

Use the description command on the FastEthernet interface Fa0/0.Configure the clock rate of the FastEthernet interface Fa0/0.

Use the no shutdown command on the FastEthernet interface Fa0/0.Reboot the router.

Showing 2 of 4 Next>Page: GO


17/29






18/29

4

Refer to the exhibit. A user wants to access the Internet from the PC. A part of the runningconfiguration of the router is shown. Which default gateway IP address should be configured at thePC to enable this access?

10.1.192.110.1.192.210.1.192.54

192.31.7.1

5

Refer to the exhibit. Assume all devices are using default configurations. How many subnets arerequired to address the topology that is shown?

134

57

6


7 15/01/2010 23:51


19/29

Refer to the exhibit. Which option shows the correct topology given the configuration of Router1?

7

Refer to the exhibit. The command that is shown was issued on a PC. What does the IP address192.168.33.2 represent?

IP address of the host

default gateway of the hostIP address of the homepage for the hostprimary domain name server for the hostIP address of the website resolver1.mooki.local


7 15/01/2010 23:51


20/29

8 A technician is setting up a workgroup for six users and wants to allow users to share files withoutsetting up a server. Which application layer protocol will provide for peer-to-peer file sharing in aworkgroup?

DNSSMBHTTPDHCP

9

Refer to the exhibit. Which option correctly identifies the network address, range of host addresses,

and the broadcast address for the network that contains host A?

0 Which statement is true about router hostnames?A hostname should be unique on each router.A router hostname cannot contain capital letters.A router hostname is configured in privileged executive mode.A router hostname must be created before any other configurations can be added to the device.


7 15/01/2010 23:51


21/29

1

Refer to the exhibit. Which Layer 2 protocol could be used inside nework A and network C?IPTCPUDPEthernet

2 What are three characteristics of CSMA/CD? (Choose three.)

Devices listen to the media and transmit data only when they cannot detect another signal on themedia.All devices on the media can hear all communications.Devices communicate based on a configured priority.

After a collision occurs, the devices that caused the collision have first priority when attempting toretransmit.When a collision occurs, all devices stop transmitting for a randomly generated period of time.

CSMA/CD uses a token system to avoid collisions.

3


7 15/01/2010 23:51


22/29

Refer to the exhibit. Host A is unable to reach host B on the remote network. A technician attemptedto ping the local gateway and the ping was successful. To verify the host configuration, the

technician issued the ipconfig command. What is the likely cause of the problem?The local NIC is incorrectly configured.The subnet mask on host A is incorrectly configured.The IP address on host A is incorrectly configured.The default gateway on host A is incorrectly configured.

4 An organization has been assigned network ID 10.10.128.0 and subnet mask 255.255.224.0. WhichIP address range can be used for this organization?

10.10.128.0 to 10.10.160.25510.10.128.0 to 10.10.159.25510.10.128.0 to 10.10.192.25510.10.128.0 to 10.10.0.15910.10.128.0 to 10.10.159.0

5

Refer to the exhibit. A PC is connected to a network. Which action will verify that the PC cancommunicate with its default gateway?

Use the ping 127.0.0.1 command.

Use the ipconfig command.

Use the ipconfig/all command.


7 15/01/2010 23:51


23/29

se the ping 10.0.0.254command.



24/29



Time Remaining: 00:19:20



25/29

9 How can ARP be used to help document the network?

It can list each hop on the way to a destination host.It can show the average latency of hosts on the network.It can provide a list of physical addresses on the network.It can indicate which hosts are not responding to network traffic.

0 Which device should be used for enabling a host to communicate with another host on a differentnetwork?

switchhubrouterhost



26/29

All contents copyright 1992-2009 Cisco Systems, Inc. Privacy Statement and Trademarks


3 15/01/2010 2355


27/29

Exam ResultsSkip to Domain Knowledge - Weighted Score | Skip to Personalized Feedback | Skip to

Secondary Scores

Exam Results - ENetwork Final Exam - CCNA Exploration: Network Fundamentals(Version 4.0)

Date Exam was Taken: 15/01/2010

Domain Knowledge - Weighted Score

Max Points: 102

Earned Points: 94

Percentage: 92.2%

Personalized Feedback has been generated based on your responses to this exam. Click Here to view yourPersonalized Feedback

Domain Knowledge - Binary Score

Max Points: 50

Earned Points: 46

Percentage: 92.0%

Close

l contents copyright 1992-2009 Cisco Systems, Inc. Privacy Statement and Trademarks

http://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtml

1 16/01/2010 00:09


28/29

Corrections after feedback- 4 errors

40 Which statement is true about router hostnames?A hostname should be unique on each router.A router hostname cannot contain capital letters.A router hostname is configured in privileged executive mode.A router hostname must be created before any other configurations can be added to

the device.

CCNA Exploration: Network Fundamentals Version 4.0

Chapter 11: Configuring and Testing Your Network

11.2 Applying a Basic Configuration Using Cisco IOS

11.2.1 Devices Need Names

46 Which range of port numbers are reserved for services that are commonlyused by applications that run on servers?0 to 2550 to 10231024 to 4915149152 to 65535


Chapter 4: OSI Transport Layer

4.1 Roles of the Transport Layer

4.1.5 Port Addressing

21 Which table accurately associates the RFC 1918 private IP addresses withthe correct network mask?


Chapter 6: Addressing the Network - IPv4

6.2 Addresses for Different Purposes

6.2.5 Public and Private Addresses


29/29

26A network administrator subnets the network 192.168.1.0/24 into foursubnets. Which option correctlyaddresses Router1 and host A into the second subnet created?


Chapter 6: Addressing the Network - IPv4

6.5 Calculating Addresses

6.5.1 Basic subnetting

Documents

38333780 CCNA Exploration Network Fundamentals Ver4 0 Enetwork Final Exam v1 92 With Feedback Corrections