4 2-Way/2 Position Valves 2-WAY - Tri-State · PDF file2-Way/2 Position Valves Flow Diagrams ... Seals and Disc NBR Core Tube 305 Stainless Steel Core and ... 8215 2-WAY Features

4 2-W

AY

1

2-Way/2 Position Valves

Two-way solenoid valves have one inlet and one outlet,and are used to permit and shut off fluid flow.

Two Types of Operations ApplyNormally Closed (NC)Fluid is shut off when the coil is de-energized, flows throughthe valve when the coil is energized .Normally Open (NO)Fluid flows through the valve when the coil is de-energized,shuts off when the coil is energized .

Two Types of Constructions ApplyDirect ActingWhen the solenoid is energized, the core directly opens theorifice of a Normally Closed valve or closes the orifice in aNormally Open valve. The valve will operate at pressuresfrom 0 psi to its rated maximum. The force needed to openthe valve is proportional to the orifice size and fluid pressure.As orifice size increases, so does the required force. To openlarger orifices without increasing solenoid size, internalpilots are used.

Internally Piloted These valves use line pressure to assist operation. When the coil is de-energized (on a Normally Closed valve),the pilot orifice is closed and line pressure is applied to the topof the piston or diaphragm through the bleed orifice, closingthe valve. When the coil is energized, the core opens the pilotorifice, relieving pressure from the diaphragm or piston. Linepressure, alone, opens the valve by lifting the diaphragm orpiston off the main orifice.

See Engineering Section for further details.

Standard and Optional FeaturesSolenoid valves are supplied, as listed, with either RedHat IImolded epoxy solenoids or RedHat solenoids with metalenclosures. RedHat II valves are identified by the letter “G” or“H” in their catalog numbers ; e.g., 8030G016. Many optionalfeatures may be added to your valves; e.g., high-temperatureClass H molded coils, manual operators, and metering devices. See the Optional Features Section for details.

Index

2-Way/2 Position Valves Flow Diagrams

Normally Closed ValveDe-Energized

Normally Closed ValveEnergized

Normally Open Valve De-Energized

Normally Open Valve Energized

Series General Description Pipe Size (NPT) Page

8030 Low Pressure 3/8" - 3/4" 3

8040/8215 Aluminum Body 1/8" - 3" 7

8210 General Service 3/8" - 2 1/2" 11

8221 Slow Closing 3/8" - 2 1/2" 17

8223 High Pressure 1/4" - 3/4" 21

8256 Subminiature 1/8" 23

8260 Plastic Body 1/4" - 3/8" 27

8262/8263 NC General Service 1/8" - 3/8" 31

8262 NO General Service 1/8" - 1/4" 35

4

2-WAY

2

Because Time Matters...ASCO Today delivers the great products you need, when you need them. You save time and money. Just place your order by 3:00 P.M. EST and ASCO ships today.

� Guaranteed same day shipment or ASCO pays the freight� ASCO Today includes our most popular valves, valve rebuild kits, and accessories� Over 2000 of ASCO's most popular products qualify for ASCO Today's guarantee

• Solenoid Valves • Miniature Valves • Valve Monitoring Systems • Pressure Switches

As part of our continued drive for customer service, we expanded the ASCO Today program with over 40,000 products that can be shipped within five business days.

TM

Products may vary in Canada, please call 1-519-758-2700 to check availability of specific catalog numbers.

Because Performance Matters ASCO is Committed to Technology, Leadership, and Service.For more information on how you can have the ASCO products you want when you want them, visit us online to see our complete listing of ASCO Today products or call 1-800-972-2726.

w w w. a s c o v a l v e . c o m

ASCO Today is registered in the United States.

42/2

SERIES

8030 2-W

AY

% ^ # )Features• Operate at low pressures: no minimum required; up

to 15 psi (1 bar) maximum differential

• Normally closed or normally open operation

• Widely used for dispensing, collating, gas shutoff,vacuum holding, and tank draining applications

• Normally open valve well suited for venting systems

Direct ActingLow Pressure Solenoid Valves

Brass or Stainless Steel Bodies3/8" to 3/4" NPT

NC

NO

Solenoid Enclosures

Nominal Ambient Temp. RangesAC: 32˚F to 125˚F (0˚C to 52˚C) DC: 32˚F to 104˚F (0˚C to 40˚C) Refer to Engineering Section for details.

ApprovalsCSA certified. UL listed, as indicated. FM approved(Normally closed only except 8030G017 and 8030G067).Meets applicable CE directives.Refer to Engineering Section for details.

Standard: Watertight, Types 1, 2, 3, 3S, 4, and 4X (all except 16.8 watt).Metal Type 1 General Purpose housing with 7/8" hole for 1/2" conduit hub (16.8 watt) Optional: Explosionproof and Watertight, Types 3, 3S, 4, 4X, 6, 6P, 7, and 9.(To order, add prefix “EF” to catalog number.)Note: Wattages 16.1 and 20.1 meet Type 7 Groups A, B, C, and D; and Type 9 Groups E and F only. See Optional Features Section for other available options.

Valve Parts in Contact with Fluids

Body Brass 304 Stainless Steel

Seals and Disc NBR

Core Tube 305 Stainless Steel

Core and Plugnut 430F Stainless Steel

Core Spring 302 Stainless Steel

Shading Coil Copper Silver

Stem PA (Normally Open)

StandardCoil andClass of

Insulation

Watt Rating and PowerConsumption Spare Coil Part Number

DCWatts

AC General Purpose Explosionproof

WattsVA

HoldingVA

Inrush AC DC AC DCF 10.6 6.1 16 40 238210 238310 238214 238314F 11.6 10.1 25 70 238610 238710 238614 238714F - 16.1 35 95 272610 - 272614 -F 16.8 - - - - 97617 - 97617F - 17.1 40 93 238610 - 238614 -F - 20.1 48 240 272610 - 272614 -

Standard Voltages: 24, 120, 240, 480 volts AC, 60 Hz (or 110, 220 volts AC, 50 Hz),6, 12, 24, 120, 240 volts DC. Must be specified when ordering.Other voltages available when required.

Construction

3

Electrical

8030R2

2/2SERIES

8030 4

2-WAY

4

Specifications (Metric units)

PipeSize(ins.)

OrificeSize(ins.)

CvFlow

Factor

Operating PressureDifferential (psi) Max. Fluid

Temp. ˚F

Brass Body Stainless Steel BodyWatt Rating/Class of CoilInsulation �

Min.

Max. AC Max. DC

CatalogNumber

Const.Ref.

UL �Listing

CatalogNumber

Const.Ref.

UL �Listing

Air-InertGas Water

Air-InertGas Water AC DC AC DC

NORMALLY CLOSED (Closed when de-energized)

3/8 3/8 1.8 0 7 5 3 3 180 120 8030G010 1 � 8030G064 1 � 6.1/F 10.6/F

3/8 3/8 1.8 0 15 15 3.5 3.5 200 150 8030G013 2 � 8030G065 2 � 10.1/F 11.6/F

1/2 7/16 2.8 0 4 6 - - 125 - 8030G016 3 � 8030G066 3 � 6.1/F -

1/2 7/16 2.8 0 - - 6 6 - 180 8030A017 11 � 8030A067 11 � - 16.8/F

1/2 7/16 2.8 0 15 15 - - 200 - 8030G017 11 � 8030G067 11 � 16.1/F -

3/4 3/4 5 0 2 2 1 1 200 150 8030G003 9 � - - - 10.1/F 11.6/F

3/4 3/4 5 0 4 4 - - 180 - 8030G043 9 � - - - 17.1/F -

3/4 5/8 5.4 0 2.5 2.5 - - 200 - - - - 8030G063 10 � 10.1/F -

NORMALLY OPEN (Open when de-energized)

3/8 3/8 1.6 0 15 15 - - 200 - 8030G070 12 � - - - 16.1/F -

1/2 7/16 2.2 0 15 15 - - 200 - 8030G071 13 � - - - 20.1/F -

1/2 3/4 5 0 2 2 - - 180 - 8030G082 7 � - - - 10.1/F -

3/4 3/4 5.5 0 2 2 - - 180 - 8030G083 8 � - - - 10.1/F -

� On all 50 hertz service, the watt rating for the 6.1/F solenoid is 8.1 watts.� � = Safety Shutoff Valve; � = General Purpose Valve. Refer to Engineering Section (Approvals) for details.

PipeSize(ins.)

OrificeSize(mm)

Kv FlowFactor(m3/h)

Operating PressureDifferential (bar) Max. Fluid

Temp. ˚C

Brass Body Stainless Steel BodyWatt Rating/Class of CoilInsulation �

Min.

Max. AC Max. DC

CatalogNumber

Const.Ref.

UL �Listing

CatalogNumber

Const.Ref.

UL �Listing

Air-InertGas Water

Air-InertGas Water AC DC AC DC


3/8 10 1.5 0 0.5 0.3 0.2 0.2 82 49 8030G010 1 � 8030G064 1 � 6.1/F 10.6/F

3/8 10 1.5 0 1.0 1.0 0.2 0.2 93 65 8030G013 2 � 8030G065 2 � 10.1/F 11.6/F

1/2 11 2.4 0 0.3 0.4 - - 52 - 8030G016 3 � 8030G066 3 � 6.1/F -

1/2 11 2.4 0 - - 0.4 0.4 - 82 8030A017 11 � 8030A067 11 � - 16.8/F

1/2 11 2.4 0 1.0 1.0 - - 93 - 8030G017 11 � 8030G067 11 � 16.1/F -

3/4 19 4.3 0 0.1 0.1 0.1 0.1 82 65 8030G003 9 � - - - 10.1/F 11.6/F

3/4 19 4.3 0 0.3 0.3 - - 82 - 8030G043 9 � - - - 17.1/F -

3/4 16 4.6 0 0.2 0.2 - - 93 - - - - 8030G063 10 � 10.1/F -


3/8 10 1.4 0 1.0 1.0 - - 93 - 8030G070 12 � - - - 16.1/F -

1/2 11 1.9 0 1.0 1.0 - - 93 - 8030G071 13 � - - - 20.1/F -

1/2 19 4.3 0 0.1 0.1 - - 82 - 8030G082 7 � - - - 10.1/F -

3/4 19 4.7 0 0.1 0.1 - - 82 - 8030G083 8 � - - - 10.1/F -

� On all 50 hertz service, the watt rating for the 6.1/F solenoid is 8.1 watts.� � = Safety Shutoff Valve; � = General Purpose Valve. Refer to Engineering Section (Approvals) for details.

Specifications (English units)

8030R2

2/2SERIES

80304 2-W

AY

5

Dimensions: inches (mm)

Const. Ref. 1, 2, 3

Const. Ref. 7, 8

Const.Ref. H K L P W

1ins. 3.85 3 1.91 3.41 1.69mm 98 76 49 87 43

2ins. 4 3.14 1.91 3.55 1.95mm 102 80 49 90 50

3ins. 4.07 3.25 2.28 3.63 1.69mm 103 83 58 92 43

7ins. 3.97 1.88 2.81 2.85 2.29mm 101 48 71 72 58

8ins. 3.97 1.88 2.81 2.85 2.29mm 101 48 71 72 58

9ins. 4.1 2.44 2.81 3.41 2.28mm 104 62 71 87 58

10ins. 4.16 2.47 2.81 3.44 2.28mm 106 63 71 87 58

11ins. 4.31 3.39 2.28 3.77 2.06mm 110 86 58 96 52

12ins. 4.16 1.1 1.91 3.72 2.06mm 106 28 49 94 52

13ins. 4.37 1.05 2.28 3.83 2.06mm 111 27 58 97 52

IMPORTANT: Valves may be mounted in any position,except for 8030G003 DC, which must be mountedwith the solenoid vertical and upright.

8030R2

4

2-WAY

2/2SERIES

8030


Const. Ref. 11, 12, 13

Const. Ref. 9, 10

6

8030R2

42/2

SERIES80408215

2-W

AY

Features• Lightweight, low-cost valves for air service

• Ideal for low pressure applications

• Provides high flow, Cv up to 138 (Kv 118)

• Air and vacuum service

Direct Acting or PilotedAluminum Body Solenoid Valves

1/8" to 3" NPT

NC

NO

Solenoid EnclosuresApprovals:CSA certified to:8040 Series:1) Standard C22.2 No. 139 "Electrically Operated

Valves," File 10381.2) Automatic Gas Valves Z21.21 (6.5), File 112872.3) Automatic Gas Safety Shutoff Valves C/I (3.9),

File 112872.8215 Series Normally Closed:1) Standard C22.2 No. 139 "Electrically Operated

Valves," File 10381.2) Automatic Gas Valves Z21.21 (6.5), File 112872.8215 Series Normally Open:1) Standard C22.2 No. 139 "Electrically Operated

Valves," File 10381. UL listed, as indicated. FM approved (Normally Closedonly, except Catalog Numbers 8215A090 and 8215A040).RedHat II meets applicable CE directives.Refer to Engineering Section for details.

Standard: RedHat II - Watertight, Types 1, 2, 3, 3S, 4, and 4X; RedHat - Type I.Optional: RedHat II - Explosionproof and Watertight, Types 3, 3S, 4, 4X, 6, 6P, 7, and 9; RedHat - Explosionproof and Raintight, Types 3, 7, and 9.(Except EF8215A40 and EF8215A90, which are suitable for Types 3 and 7(C and D) only and have a T2B temperature rating code.) To order, add prefix “EF” to catalog number. See Optional Features Section for other available options.

8040

Valve Parts in Contact with Fluids Body AluminumSeals, Diaphragms, Disc NBRDisc-Holder PA (10.1 and 11.6 watt Normally Open only)Core Guide CACore Tube 305 Stainless SteelRider Rings PTFECore and Plugnut 430F Stainless SteelSprings* 302 Stainless SteelShading Coil Copper* For 8040H006, 8040H007, 8040H008, spring material is 17-7 PH


Insulation

Watt Rating and PowerConsumption Spare Coil Part No.

DCWatts


WattsVA

HoldingVA

Inrush AC DC AC DCF - 6.1 16 40 238210 - 238214 -F 11.6 10.1 25 70 238610 238710 238614 238714B 14.9 - - - - 62691 - -F - 15.4 27 160 99257 - 99257 -F - 28.2 50 385 206409 - 206409 -

Standard Voltages: 24, 120, 240, 480 volts AC, 60 Hz (or 110, 220 volts AC, 50 Hz),6, 12, 24, 120, 240 volts DC. Must be specified when ordering. Other voltages available when required. (Note: 24 volt AC, 60 Hz not available with 28.2 watt coil)

Electrical

Nominal Ambient Temp. Ranges

% ^ # )

7

Construction

SeriesAC DC

RedHat II/RedHat RedHat II RedHat

8040 -40˚F to 125˚F(-40˚C to 52˚C) - -

8215 32˚F to 125˚F(0˚C to 52˚C)

32˚F to 104˚F(0˚C to 40˚C)

32˚F to 77˚F(0˚C to 25˚C)

(104˚F/40˚C occasionally)Refer to Engineering Section for details.

8040_8215R2

2/2SERIES80408215 4

2-WAY

PipeSize(ins.)

OrificeSize(ins.)

CvFlow

Factor

GasCapacityBtu/hr �

Operating PressureDifferential (psi)

Max.Fluid

Temp. ˚F Aluminum BodyConst.Ref.

UL �Listing

Watt Rating/Class of CoilInsulation �

Min.

Max. AC Max. DC

Air-FuelGas

Air-FuelGas AC DC Catalog Number AC DC AC DC


1/8 5/16 1.0 53,700 0 15 - 125 - 8040H006 11 � 6.1/F -

1/4 5/16 1.1 59,000 0 15 - 125 - 8040H007 11 � 6.1/F -

3/8 5/16 1.2 64,400 0 15 - 125 - 8040H008 11 � 6.1/F -

3/8 3/4 3.4 183,000 0 50 25 125 104 8215G010 2 � 10.1/F 11.6/F

3/8 3/4 3.5 - 5 125 125 125 104 8215G001 � 1 � 6.1/F 11.6/F

1/2 3/4 5.4 291,000 0 2 - 125 - 8040G022 13A � 10.1/F -

1/2 3/4 4.4 238,500 0 50 25 125 104 8215G020 2 � 10.1/F 11.6/F

1/2 3/4 4.8 - 5 125 125 125 104 8215G002 � 1 � 6.1/F 11.6/F

3/4 3/4 9.5 512,000 0 2 - 125 - 8040G023 13B � 10.1/F -

3/4 3/4 5.1 247,500 0 50 25 125 104 8215G030 4 � 10.1/F 11.6/F

3/4 3/4 5.1 - 5 125 125 125 104 8215G003 � 3 � 6.1/F 11.6/F

1 1 5/8 21 1,119,000 0 25 25 125 77 8215B050 � 6 16 � 15.4/F 14.9/B

1 1/4 1 5/8 32 1,730,000 0 25 25 125 77 8215B060 � 6 16 � 15.4/F 14.9/B

1 1/2 1 5/8 35 1,900,000 0 25 25 125 77 8215B070 � 6 16 � 15.4/F 14.9/B

2 2 3/32 60 3,251,000 0 25 15 125 77 8215B080 � 7 17 � 15.4/F 14.9/B

2 1/2 3 117 5,821,000 0 5 - 125 - 8215A090 � 8 � 28.2/F -

3 3 138 7,430,000 0 5 - 125 - 8215A040 � 8 � 28.2/F -


3/8 3/4 3.2 172,500 0 125 125 125 104 8215G013 9 � 10.1/F 11.6/F

1/2 3/4 4 206,250 0 125 125 125 104 8215G023 9 � 10.1/F 11.6/F

3/4 3/4 4.6 247,500 0 125 125 125 104 8215G033 10 � 10.1/F 11.6/F

1 1 5/8 22 1,191,750 0 25 15 125 77 8215C053 12 18 � 15.4/F 14.9/B

1 1/4 1 5/8 33 1,793,250 0 25 15 125 77 8215C063 12 18 � 15.4/F 14.9/B

1 1/2 1 5/8 37 1,988,250 0 25 15 125 77 8215C073 13 19 � 15.4/F 14.9/B

2 2 3/32 58 3,100,000 0 25 15 125 77 8215C083 14 20 � 15.4/F 14.9/B

2 1/2 3 117 6,290,000 0 5 - 125 - 8215B093 � 15 � 28.2/F -

� Do not use for Fuel Gas.� On 50 hertz service, the watt rating for the 6.1/F solenoid is 8.1 watts.� FM Approved Process Control Valves. See Engineering Section (Approvals) for details. Type I enclosure only.� � = Safety Shutoff Valve; � = General Purpose Valve. Refer to Engineering Section (Approvals) for details. � 1" W.C. Drop @ 2" W.C. Inlet Pressure, 1,000 Btu/cu.ft. or more, 0.64 Specific Gravity Gas.� Not available with 24 volt, 60 Hz coil.

8


8040_8215R2

2/2SERIES

804082154 2-

WAY

PipeSize(ins.)

OrificeSize(mm)

Kv FlowFactor(m3/h)

GasCapacityBtu/hr �

Operating PressureDifferential (bar)

Max.Fluid

Temp.˚C Aluminum BodyConst.Ref.

UL �Listing


Min.

Max. AC Max. DC

Air-FuelGas

Air-FuelGas AC DC Catalog Number AC DC AC DC


1/8 7.9 .86 53,700 0 1.0 - 52 - 8040H006 11 � 6.1/F -

1/4 7.9 .94 59,000 0 1.0 - 52 - 8040H007 11 � 6.1/F -

3/8 7.9 1.0 64,400 0 1.0 - 52 - 8040H008 11 � 6.1/F -

3/8 19 2.9 183,000 0 3.4 1.7 52 40 8215G010 2 � 10.1/F 11.6/F

3/8 19 3.0 - 0.3 8.6 8.6 52 40 8215G001 � 1 � 6.1/F 11.6/F

1/2 19 4.6 291,000 0 0.1 - 52 - 8040G022 13A � 10.1/F -

1/2 19 3.8 238,500 0 3.4 1.7 52 40 8215G020 2 � 10.1/F 11.6/F

1/2 19 4.1 - 0.3 8.6 8.6 52 40 8215G002 � 1 � 6.1/F 11.6/F

3/4 19 8.1 449,000 0 0.1 - 52 - 8040G023 13B � 10.1/F -

3/4 19 4.4 247,500 0 3.4 1.7 52 40 8215G030 4 � 10.1/F 11.6/F

3/4 19 4.4 - 0.3 8.6 8.6 52 40 8215G003 � 3 � 6.1/F 11.6/F

1 41 18 1,119,000 0 1.7 1.7 52 25 8215B050 � 6 16 � 15.4/F 14.9/B

1 1/4 41 27 1,730,000 0 1.7 1.7 52 25 8215B060 � 6 16 � 15.4/F 14.9/B

1 1/2 41 30 1,900,000 0 1.7 1.7 52 25 8215B070 � 6 16 � 15.4/F 14.9/B

2 53 51 3,251,000 0 1.7 1.0 52 25 8215B080 � 7 17 � 15.4/F 14.9/B

2 1/2 76 100 5,821,000 0 0.3 - 52 - 8215A090 � 8 � 28.2/F -

3 76 118 7,430,000 0 0.3 - 52 - 8215A040 � 8 � 28.2/F -


3/8 19 2.74 172,500 0 8.6 8.6 52 40 8215G013 9 � 10.1/F 11.6/F

1/2 19 3.4 206,250 0 8.6 8.6 52 40 8215G023 9 � 10.1/F 11.6/F

3/4 19 3.9 247,500 0 8.6 8.6 52 40 8215G033 10 � 10.1/F 11.6/F

1 41 19 1,191,750 0 1.7 1.0 52 25 8215C053 12 18 � 15.4/F 14.9/B

1 1/4 41 28 1,793,250 0 1.7 1.0 52 25 8215C063 12 18 � 15.4/F 14.9/B

1 1/2 41 32 1,988,250 0 1.7 1.0 52 25 8215C073 13 19 � 15.4/F 14.9/B

2 53 50 3,100,000 0 1.7 1.0 52 25 8215C083 14 20 � 15.4/F 14.9/B

2 1/2 76 100 6,290,000 0 0.3 - 52 - 8215B093 � 15 � 28.2/F -

� Do not use for Fuel Gas.� On 50 hertz service, the watt rating for the 6.1/F solenoid is 8.1 watts.� FM Approved Process Control Valves. See Engineering Section (Approvals) for details. Type 1 enclosure only.� � = Safety Shutoff Valve; � = General Purpose Valve. Refer to Engineering Section (Approvals) for details.� 1" W.C. Drop @ 2" W.C. Inlet Pressure, 1,000 Btu/cu.ft. or more, 0.64 Specific Gravity Gas.� Not available with 24 volt, 60 Hz coil.

9


8040_8215R2

2/2SERIES80408215 4

2-WAY


2 CORED HOLES.350 [8.9] DEEP FOR.164-32 TH’DFORMING SCREW

.800 [20.3]

.406 [10.3]

.60 [15]

BOTTOM VIEW OF BODY

NPTBOTH ENDS

R .088 [R 2.2]4 PLACES

LFLOW

.750 [19.1].115 [2.9] 2 PLACES

.90 [23] .250 [6.4]

K

PH

1/2 NPT

W

.97 [25]

IN

Const. Ref. 11

FLOW

L

P

NPTBOTH ENDS

H

W

Ø .88 [Ø 22]HOLE FOR1/2 CONDUITCONN.

Const. Ref. 12-15, 18-20

FLOW

NPTBOTH ENDS

L

K

P

H

W

1/2 NPT

1.66 [42]

2 MOUNTING HOLESØ .28 [Ø 7.1]

Const. Ref. 1-4, 9, 10, 13A, 13BConst.Ref. H K L P W

1ins. 3.42 2.00 2.75 2.87 2.46mm 87 51 70 73 63

2ins 4.02 2.49 2.75 3.46 2.46mm 102 63 70 88 63

3ins. 3.87 2.19 3.31 3.05 2.33mm 98 56 84 77 59

4ins. 4.46 2.68 3.31 3.64 2.33mm 113 68 84 92 59

6 �ins. 6.84 4.25 5.00 5.59 5.38mm 174 108 127 142 137

7 �ins. 7.47 4.53 6.09 5.94 6.31mm 190 115 155 151 160

8 �ins. 10.25 5.75 7.79 7.91 7.94mm 260 146 198 201 202

9ins. 4.42 2.72 2.75 3.86 2.36mm 112 69 70 98 60

10ins. 4.86 2.72 3.31 4.04 2.36mm 123 69 84 103 60

11ins. 2.74 1.44 2.00 2.30 1.69mm 69 36 51 58 43

12ins. 6.84 2.22 5.00 3.63 5.38mm 174 56 127 92 137

13ins. 6.84 2.16 5.00 3.56 5.38mm 174 55 127 90 137

13Ains. 4.05 2.46 2.75 3.44 2.42mm 103 63 70 87 62

13Bins. 4.49 2.65 3.31 3.63 2.39mm 114 67 84 92 61

14 �ins. 7.44 2.41 6.09 3.81 6.31mm 189 61 155 97 160

15 �ins. 10.25 3.07 7.80 5.22 7.94mm 260 78 198 133 202

16ins. 7.59 4.03 5.00 6.34 5.38mm 193 102 127 161 137

17ins. 8.19 4.38 6.09 6.69 6.31mm 208 111 155 170 160

18ins. 6.16 2.09 5.00 4.41 5.38mm 156 53 127 112 137

19ins. 7.59 2.03 5.00 4.34 5.38mm 193 52 127 110 137

20ins. 8.19 2.28 6.09 4.59 6.31mm 2.08 58 155 117 160

IMPORTANT: Valves may be mounted in any positionexcept all DC constructions and those marked �, whichmust be mounted with the solenoid vertical and upright.Constructions marked � must be mounted with the solenoid vertical and upright or horizontal only.

10

Const. Ref. 6, 7, 8, 16, 17

P

H

L

K

W

NPTBOTH ENDS

7/8 DIA HOLEFOR 1/2 CONDUIT CONN.

FLOW

8040_8215R2

2/2SERIES

8210

Features• Wide range of pressure ratings, sizes, and resilient

materials provide long service life and low internal leakage

• High Flow Valves for liquid, corrosive, and air/inert gas service

• Industrial applications include:- Car wash - Laundry equipment- Air compressors - Industrial water control- Pumps

Pilot OperatedGeneral Service Solenoid Valves

Brass or Stainless Steel Bodies3/8" to 2 1/2" NPT

NC

NO

Solenoid Enclosures

Electrical

Nominal Ambient Temp. RangesRedHat II/RedHat AC: 32˚F to 125˚F (0˚C to 52˚C)

RedHat II DC: 32˚F to 104˚F (0˚C to 40˚C)RedHat DC: 32˚F to 77˚F (0˚C to 25˚C)


ApprovalsUL listed as indicated. CSA certified. RedHat II meets applicable CE directives.Refer to Engineering Section for details.

Standard: RedHat II - Watertight, Types 1, 2, 3, 3S, 4, and 4X; RedHat - Type I.Optional: RedHat II - Explosionproof and Watertight, Types 3, 3S, 4, 4X, 6, 6P,7, and 9; Red-Hat - Explosionproof and Watertight, Types 3, 4, 4X, 7, and 9.(To order, add prefix “EF” to catalog number, except Catalog Numbers 8210B057,8210B058, and 8210B059, which are not available with Explosionproof enclosures.)See Optional Features Section for other available options.

Construction

4 2-W

AY

11

^ % )


Body Brass 304 Stainless Steel

Seals and Discs NBR or PTFE

Disc-Holder PA



Springs 302 Stainless Steel



Insulation

Watt Rating and PowerConsumption Spare Coil Part Number

DCWatts


WattsVA

HoldingVA

Inrush AC DC AC DCF - 6.1 16 40 238210 - 238214 -F 11.6 10.1 25 70 238610 238710 238614 238714F 16.8 16.1 35 180 272610 97617 272614 97617F - 17.1 40 93 238610 - 238614 -F - 20 43 240 99257 - 99257 -F - 20.1 48 240 272610 - 272614 -H 30.6 - - - - 74073 - 74073H 40.6 - - - - 238910 - 238914

Standard Voltages: 24, 120, 240, 480 volts AC, 60 Hz (or 110, 220 volts AC, 50Hz). 6, 12, 24, 120, 240 volts DC. Must be specified when ordering.Other voltages available when required.

8210R2

2/2SERIES

8210 4

2-WAY

12


PipeSize(ins.)

OrificeSize(ins.)

CvFlow

Factor

Operating Pressure Differential (psi)Max. FluidTemp. ˚F Brass Body Stainless Steel Body


Min.

Max. AC Max. DC

Air-InertGas Water

Light Oil @300 SSU

Air-InertGas Water

Light Oil @300 SSU AC DC

CatalogNumber

Const.Ref. �

UL �Listing

CatalogNumber

Const.Ref. �

UL �Listing AC DC

NORMALLY CLOSED (Closed when de-energized), NBR or PTFE � Seating3/8 3/8 1.5 � 150 125 - 40 40 - 180 150 8210G073 � 1P � 8210G036 � 1P � 6.1/F 11.6/F3/8 5/8 3 0 150 150 - 40 40 - 180 150 8210G093 5D � - - - 10.1/F 11.6/F3/8 5/8 3 5 200 150 135 125 100 100 180 150 8210G001 6D � - - - 6.1/F 11.6/F3/8 5/8 3 5 300 300 300 - - - 175 - 8210G006 5D � - - - 17.1/F -1/2 7/16 2.2 � 150 125 - 40 40 - 180 150 8210G015 � 2P � 8210G037 � 2P � 6.1/F 11.6/F1/2 5/8 4 0 150 150 - 40 40 - 180 150 8210G094 5D � - - - 10.1/F 11.6/F1/2 5/8 4 0 150 150 125 40 40 - 175 150 - - - 8210G087 7D � 17.1/F 11.6/F1/2 5/8 4 5 200 150 135 125 100 100 180 150 8210G002 6D � - - - 6.1/F 11.6/F1/2 5/8 4 5 300 300 300 - - - 175 - 8210G007 5D � - - - 17.1/F -1/2 3/4 4 5 - 300 - - 300 - 180 125 8210G227 5D � - - - 17.1/F 40.6/H3/4 5/8 4.5 0 150 150 125 40 40 - 175 150 - - - 8210G088 7D � 17.1/F 11.6/F3/4 3/4 5 5 125 125 125 100 90 75 180 150 8210G009 9D � - - - 6.1/F 11.6/F3/4 3/4 5 0 150 150 - 40 40 - 180 150 8210G095 8D � - - - 10.1/F 11.6/F3/4 3/4 6.5 5 250 150 100 125 125 125 180 150 8210G003 11D � - - - 6.1/F 11.6/F3/4 3/4 6 0 - - - 200 180 180 - 77 8210B026 � ‡ 10P - - - - - 30.6/H3/4 3/4 6 0 350 300 200 - - - 200 - 8210G026 � ‡ 40P � - - - 16.1F -1 1 13 0 - - - 100 100 80 - 77 8210B054 ‡ 31D - 8210D089 15D - - 30.6/H1 1 13 0 150 125 125 - - - 180 - 8210G054 41D � 8210G089 45D � 16.1/F -1 1 13 5 150 150 100 125 125 125 180 150 8210G004 12D � - - - 6.1/F 11.6/F1 1 13.5 0 300 225 115 - - - 200 - 8210G027 ‡ 42P � - - - 20.1/F -1 1 13.5 10 300 300 300 - - - 175 - 8210G078 � 13P - - - - 17.1/F -

1 1/4 1 1/8 15 0 - - - 100 100 80 - 77 8210B055 ‡ 32D - - - - - 30.6/H1 1/4 1 1/8 15 0 150 125 125 - - - 180 - 8210G055 43D � - - - 16.1/F -1 1/4 1 1/8 15 5 150 150 100 125 125 125 180 150 8210G008 16D � - - - 6.1/F 11.6/F1 1/2 1 1/4 22.5 0 - - - 100 100 80 - 77 8210B056 ‡ 33D - - - - - 30.6/H1 1/2 1 1/4 22.5 0 150 125 125 - - - 180 - 8210G056 44D � - - - 16.1/F -1 1/2 1 1/4 22.5 5 150 150 100 125 125 125 180 150 8210G022 18D � - - - 6.1/F 11.6/F

2 1 3/4 43 5 150 125 90 50 50 50 180 150 8210G100 20P � - - - 6.1/F 11.6/F2 1/2 1 3/4 45 5 150 125 90 50 50 50 180 150 8210G101 21P � - - - 6.1/F 11.6/F

NORMALLY OPEN (Open when de-energized), NBR Seating (PA Disc-Holder, except as noted)3/8 5/8 3 0 150 150 125 125 125 80 180 150 8210G033 23D � - - - 10.1/F 11.6/F3/8 5/8 3 5 250 200 200 250 200 200 180 180 8210G011 39D � - - - 10.1/F 11.6/F1/2 5/8 4 0 150 150 125 125 125 80 180 150 8210G034 23D � - - - 10.1/F 11.6/F1/2 5/8 3 0 150 150 100 125 125 80 180 150 - - - 8210G030 37D � 10.1/F 11.6/F1/2 5/8 4 5 250 200 200 250 200 200 180 180 8210G012 39D � - - - 10.1/F 11.6/F3/4 3/4 5.5 0 150 150 125 125 125 80 180 150 8210G035 25D � - - - 10.1/F 11.6/F3/4 5/8 3 0 150 150 100 125 125 80 180 150 - - - 8210G038 38D � 10.1/F 11.6/F3/4 3/4 6.5 5 - - - 250 200 200 - 180 8210C013 24D � - - - - 16.8/F3/4 3/4 6.5 5 250 200 200 - - - 180 - 8210G013 46D � - - - 16.1/F -1 1 13 0 125 125 125 - - - 180 - 8210B057 � � 34D � - - - 20/F -1 1 13 5 - - - 125 125 125 - 180 8210D014 26D � - - - - 16.8/F1 1 13 5 150 150 125 - - - 180 - 8210G014 47D � - - - 16.1/F -

1 1/4 1 1/8 15 0 125 125 125 - - - 180 - 8210B058 � � 35D � - - - 20/F -1 1/4 1 1/8 15 5 - - - 125 125 125 - 180 8210D018 28D � - - - - 16.8/F1 1/4 1 1/8 15 5 150 150 125 - - - 180 - 8210G018 48D � - - - 16.1/F -1 1/2 1 1/4 22.5 0 125 125 125 - - - 180 - 8210B059 � � 36D � - - - 20/F -1 1/2 1 1/4 22.5 5 - - - 125 125 125 - 180 8210D032 29D � - - - - 16.8/F1 1/2 1 1/4 22.5 5 150 150 125 - - - 180 - 8210G032 49D � - - - 16.1/F -

2 1 3/4 43 5 - - - 125 125 125 - 150 8210 103 30P � - - - - 16.8/F2 1 3/4 43 5 125 125 125 - - - 180 - 8210G103 50P � - - - 16.1/F -

2 1/2 1 3/4 45 5 - - - 125 125 125 - 150 8210 104 27P � - - - - 16.8/F2 1/2 1 3/4 45 5 125 125 125 - - - 180 - 8210G104 51P � - 16.1/F -

� 5 psi on Air; 1 psi on Water. � Valves not available with Explosionproof enclosures.� Valve provided with PTFE main disc. � On 50 hertz service, the watt rating for the 6.1/F solenoid is 8.1 watts.� Valve includes UItem (G.E. trademark) piston. AC construction also has PA seating. � Letter “D” denotes diaphragm construction; “P” denotes piston construction. No disc-holder.� � Safety Shutoff Valve; � General Purpose Valve. � Stainless steel disc-holder.Refer to Engineering Section (Approvals) for details. ‡ Must have solenoid mounted vertical and upright.

8210R2

2/2SERIES

82104 2-W

AY

13

PipeSize(ins.)

OrificeSize(mm)

Kv FlowFactor(m3/h)

Operating Pressure Differential (bar) Max.Fluid

Temp. ˚C Brass Body Stainless Steel Body

Watt Rating/Class of Coil Insulation �

Min.

Max. AC Max. DC

Air-InertGas Water

Light Oil @300 SSU

Air-InertGas Water

Light Oil @300 SSU AC DC

CatalogNumber

Const.Ref. �

UL �Listing

CatalogNumber

Const.Ref. �

UL �Listing AC DC

NORMALLY CLOSED (Closed when de-energized), NBR or PTFE � Seating3/8 10 1.3 � 10 9 - 3 3 - 82 65 8210G073 � 1P � 8210G036 � 1P � 6.1/F 11.6/F3/8 16 2.6 0 10 10 - 3 3 - 82 65 8210G093 5D � - - - 10.1/F 11.6/F3/8 16 2.6 0.3 14 10 9 9 7 7 82 65 8210G001 6D � - - - 6.1/F 11.6/F3/8 16 2.6 0.3 21 21 21 - - - 79 - 8210G006 5D � - - - 17.1/F -1/2 11 1.9 � 10 9 - 3 3 - 82 65 8210G015 � 2P � 8210G037 � 2P � 6.1/F 11.6/F1/2 16 3.4 0 10 10 - 3 3 - 82 65 8210G094 5D � - - - 10.1/F 11.6/F1/2 16 3.4 0 10 10 9 3 3 - 79 65 - - - 8210G087 7D � 17.1/F 11.6/F1/2 16 3.4 0.3 14 10 9 9 7 7 82 65 8210G002 6D � - - - 6.1/F 11.6/F1/2 16 3.4 0.3 21 21 21 - - - 79 - 8210G007 5D � - - - 17.1/F -1/2 19 3.4 0.3 - 21 - - 21 - 82 52 8210G227 5D � - - - 17.1/F 40.6H3/4 16 3.9 0 10 10 9 3 3 - 79 65 - - - 8210G088 7D � 17.1/F 11.6/F3/4 19 4.3 0.3 9 9 9 7 6 5 82 65 8210G009 9D � - - - 6.1/F 11.6/F3/4 19 4.3 0 10 10 - 3 3 - 82 65 8210G095 8D � - - - 10.1/F 11.6/F3/4 19 5.6 0.3 17 10 7 9 9 9 82 65 8210G003 11D � - - - 6.1/F 11.6/F3/4 19 5.1 0 - - - 14 12 12 - 25 8210B026 � ‡ 10P - - - - - 30.6/H3/4 19 5.1 0 24 21 14 - - - 93 - 8210G026 � ‡ 40P � - - - 16.1F -1 25 11 0 - - - 7 7 6 - 25 8210B054 ‡ 31D - 8210D089 15D - - 30.6/H1 25 11 0 10 9 9 - - - 82 - 8210G054 41D � 8210G089 45D � 16.1/F -1 25 11 0.3 10 10 7 9 9 9 82 65 8210G004 12D � - - - 6.1/F 11.6/F1 25 11.5 0 21 16 8 - - - 93 - 8210G027 ‡ 42P � - - - 20.1/F -1 25 11.5 0.7 21 21 21 - - - 79 - 8210G078 � 13P - - - - 17.1/F -

1 1/4 29 13 0 - - - 7 7 6 - 25 8210B055 ‡ 32D - - - - - 30.6/H1 1/4 29 13 0 10 9 9 - - - 82 - 8210G055 43D � - - - 16.1/F -1 1/4 29 13 0.3 10 10 7 9 9 9 82 65 8210G008 16D � - - - 6.1/F 11.6/F1 1/2 32 19.5 0 - - - 7 7 6 - 25 8210B056 ‡ 33D - - - - - 30.6/H1 1/2 32 19.5 0 10 9 9 - - - 82 - 8210G056 44D � - - - 16.1/F -1 1/2 32 19.5 0.3 10 10 7 9 9 9 82 65 8210G022 18D � - - - 6.1/F 11.6/F

2 44 37 0.3 10 9 6 3 3 3 82 65 8210G100 20P � - - - 6.1/F 11.6/F2 1/2 44 39 0.3 10 9 6 3 3 3 82 65 8210G101 21P � - - - 6.1/F 11.6/F

NORMALLY OPEN (Open when de-energized), NBR Seating (PA Disc-Holder, except as noted)3/8 16 2.6 0.0 10 10 9 9 9 6 82 65 8210G033 23D � - - - 10.1/F 11.6/F3/8 16 2.6 0.3 17 14 14 17 14 14 82 82 8210G011 39D � - - - 10.1/F 11.6/F1/2 16 3.4 0 10 10 9 9 9 6 82 65 8210G034 23D � - - - 10.1/F 11.6/F1/2 16 2.6 0 10 10 7 9 9 6 82 65 - - - 8210G030 37D � 10.1/F 11.6/F1/2 16 3.4 0.3 17 14 14 17 14 14 82 82 8210G012 39D � - - - 10.1/F 11.6/F3/4 19 4.7 0 10 10 9 9 9 6 82 65 8210G035 25D � - - - 10.1/F 11.6/F3/4 16 2.6 0 10 10 7 9 9 6 82 65 - - - 8210G038 38D � 10.1/F 11.6/F3/4 19 5.6 0.3 - - - 17 14 14 - 82 8210C013 24D � - - - - 16.8/F3/4 19 5.6 0.3 17 14 14 - - - 82 - 8210G013 46D � - - - 16.1/F -1 25 11 0 9 9 9 - - - 82 - 8210B057 � � 34D � - - - 20/F -1 25 11 0.3 - - - 9 9 9 - 82 8210D014 26D � - - - - 16.8/F1 25 11 0.3 10 10 9 - - - 82 - 8210G014 47D � - - - 16.1/F -

1 1/4 29 13 0 9 9 9 - - - 82 - 8210B058 � � 35D � - - - 20/F -1 1/4 29 13 0.3 - - - 9 9 9 - 82 8210D018 28D � - - - - 16.8/F1 1/4 29 13 0.3 10 10 9 - - - 82 - 8210G018 48D � - - - 16.1/F -1 1/2 32 19.5 0 9 9 9 - - - 82 - 8210B059 � � 36D � - - - 20/F -1 1/2 32 19.5 0.3 - - - 9 9 9 - 82 8210D032 29D � - - - - 16.8/F1 1/2 32 19.5 0.3 10 10 9 - - - 82 - 8210G032 49D � - - - 16.1/F -

2 44 37 0.3 - - - 9 9 9 - 65 8210 103 30P � - - - - 16.8/F2 44 37 0.3 9 9 9 - - - 82 - 8210G103 50P � - - - 16.1/F -

2 1/2 44 39 0.3 - - - 9 9 9 - 65 8210 104 27P � - - - - 16.8/F2 1/2 44 39 0.3 9 9 9 - - - 82 - 8210G104 51P � - - - 16.1/F -

� 0.3 bar on Air; 0.0 bar on Water. � Valves not available with Explosionproof enclosures.� Valve provided with PTFE main disc. � On 50 hertz service, the watt rating for the 6.1/F solenoid is 8.1 watts.� Valve includes UItem (G.E. trademark) piston. AC construction also has PA seating. � Letter “D” denotes diaphragm construction; “P” denotes piston construction. No disc-holder.� � Safety Shutoff Valve; � General Purpose Valve. � Stainless steel disc-holder.Refer to Engineering Section (Approvals) for details. ‡ Must have solenoid mounted vertical and upright.


8210R2

2/2SERIES

8210 4

2-WAY

14


KP

H

NPTBOTH ENDS

L

1/2 NPT

W

R .12 [3.2]4 PLACES

.59 [15]

.69 [18] .86 [22]

.88 [22]Ø.266 [6.8]

BOTTOM VIEW SHOWINGMOUNTING BRACKET HOLES

(OPTIONAL)FLOW

Const. Ref. 1, 2

1.656 [42]

.281 [7.1] DIA2 MOUNTINGHOLES

OPTIONAL MOUNTING BRACKET

FLOW

L

K

P

H

NPT BOTH ENDS

W

1/2 NPT

1.625 [41.3]

Const. Ref. 5-9, 11, 20, 21, 23 , 25, 37,38

Const. Ref. 13

L

W

P

K

H

NPTBOTH ENDS

FLOW


1*ins. 3.85 3.00 1.91 3.41 1.69mm 98 76 49 87 43

2*ins. 4.17 3.25 2.28 3.63 1.69mm 106 83 58 92 43

5ins. 3.84 2.31 2.75 3.28 2.28mm 98 59 70 83 58

6*ins. 3.38 1.94 2.75 2.80 2.28mm 86 49 70 71 58

7ins. 4.19 2.50 2.81 3.47 2.39mm 106 64 71 88 61

8ins. 4.13 2.47 2.81 3.44 2.29mm 105 63 71 87 58

9*ins. 3.66 2.10 2.81 2.96 2.28mm 93 53 71 75 58

10*ins. 5.25 X 2.81 4.59 2.31mm 133 X 71 117 59

11*ins. 4.16 2.66 3.84 3.52 2.75mm 106 68 98 89 70

12ins. 5.64 3.15 3.75 4.01 3.36mm 143 80 95 102 85

13ins. 4.44 3.22 3.75 4.19 5.81mm 113 82 95 106 147

15*ins. 5.34 X 3.75 4.47 3.84mm 136 X 95 114 98

16ins. 5.64 3.15 3.66 4.01 3.56mm 143 80 93 102 90

18ins. 6.11 3.30 4.38 4.16 3.92mm 155 84 111 106 100

20*ins. 7.33 3.71 5.06 4.57 4.87mm 186 94 129 116 124

21*ins. 7.33 3.71 5.50 4.57 4.87mm 186 94 140 116 124

23ins. 4.35 2.65 2.75 3.79 2.28mm 110 67 70 96 58

24ins. 5.06 X 3.78 4.44 2.75mm 129 X 96 113 70

25ins. 4.64 2.81 2.81 3.94 2.28mm 118 71 71 100 58

26ins. 6.53 X 3.75 4.91 3.19mm 166 X 95 125 81

27ins. 8.22 X 5.50 5.47 4.87mm 209 X 140 139 124

28ins. 6.53 X 3.66 4.91 3.19mm 166 X 93 125 81

29ins. 7.03 X 4.38 5.06 4.40mm 179 X 111 129 112

* DC dimensions slightly larger.IMPORTANT: Valves may be mounted in any position, except as noted in specifications table.

8210R2

2/2SERIES

82104 2-W

AY

15


K

P

H

L

FLOW

NPTBOTH ENDS

7/8 DIA. HOLE FOR1/2 CONDUIT CONN.

1.625 [41.3]

W

1.656 [42]

.281 [7.1] DIA.2 MOUNTING HOLES


Const. Ref. 10, 15, 24, 26-36

L

P

H

K

W

NPT BOTH ENDS

1/2 NPT

FLOW

IN

Const. Ref. 12, 16, 18


30ins. 8.22 X 5.06 5.47 4.87

mm 209 X 129 139 124

31ins. 5.25 X 3.75 4.44 3.25

mm 133 X 95 113 83

32ins. 5.69 X 3.66 4.69 3.25

mm 145 X 93 119 83

33ins. 6.06 X 4.38 4.94 3.91

mm 154 X 111 125 99

34ins. 6.91 X 3.75 6.09 3.25

mm 176 X 95 155 83

35ins. 7.34 X 3.66 6.34 3.25

mm 186 X 93 161 83

36ins. 7.66 X 4.38 6.56 3.91

mm 1.95 X 111 167 99

37ins. 4.61 2.75 2.81 3.89 2.39

mm 117 70 71 99 61

38ins. 4.61 2.75 2.81 3.89 2.39

mm 117 70 71 99 61

39ins. 5.42 2.31 2.75 4.86 3.80

mm 138 59 70 123 97

40ins. 5.20 3.29 2.81 4.50 2.28

mm 132 83 71 114 58

41ins. 5.13 3.10 3.75 4.32 3.25

mm 130 79 95 110 83

42ins. 6.43 4.40 3.93 5.62 3.25

mm 163 112 100 143 83

43ins. 5.57 3.35 3.66 4.57 3.25

mm 142 85 93 116 83

44ins. 5.90 3.57 4.38 4.79 3.91

mm 150 91 111 122 99

45ins. 5.26 3.17 3.75 4.38 3.84

mm 134 81 95 111 98

46ins. 4.95 3.10 3.84 4.31 2.75

mm 126 79 98 110 70

47ins. 6.43 3.59 3.75 4.81 3.52

mm 163 91 95 122 90

48ins. 6.43 3.59 3.66 4.81 3.73

mm 163 91 93 122 95

49ins. 6.91 3.75 4.38 4.96 4.40

mm 176 95 111 126 112

50ins. 8.13 4.15 5.06 5.37 4.87

mm 207 105 129 136 124

51ins. 8.13 4.15 5.50 5.37 5.18

mm 207 105 140 136 132

IMPORTANT: Valves may be mounted in any position, except as noted in specifications table.

8210R2

2/2SERIES

8210 4

2-WAY

16


NPTBOTH ENDS

K

P

H

L

FLOW

1/2 NPT

W


1.66 [42]

SHOWING MOUNTING BRACKET ONLY

Const. Ref. 39

1/2 NPT

1.656 [42]

1.625 [41.32]



W

NPTBOTH ENDS

L

FLOW

K

P

H

Const. Ref. 40-51

8210R2

42/2

SERIES

8221 2-W

AY

17

Features• Pilot operated, normally open or normally closed

• Snubber slows disc closing speed to protect systemagainst water hammer damage more effectively than other techniques

• Pressure spike due to water hammer is reduced to a point eliminating the need for suppressors or other controls in most water systems

• Fluid Controls Institute Inc. evaluations have classified these valves:Pipe Sizes FCI-82-1 Class

3/8", 1/2", 3/4" CC1", 1 1/4", 1 1/2", 2", 2 1/2" BB

Pilot OperatedSlow Closing Solenoid Valves

Brass Body • 3/8" to 2 1/2" NPT

NC

NO

Solenoid Enclosures

Nominal Ambient Temp. Ranges:RedHat II/RedHat AC: 32˚F to 125˚F (0˚C to 52˚C) RedHat II DC: 32˚F to 104˚F (0˚C to 40˚C)RedHat DC: 32˚F to 77˚F (0˚C to 25˚C)


Approvals:CSA certified. UL listed, General Purpose Valves. RedHat II meets applicable CE directives.Refer to Engineering Section for details.

Standard: RedHat II - Watertight, Types 1, 2, 3, 3S, 4, and 4X; RedHat - Type I.Optional: RedHat II - Explosionproof and Watertight, Types 3, 3S, 4, 4X, 6,6P, 7, and 9; RedHat - Explosionproof and Raintight, Types 3,7, and 9. (To order, add prefix “EF” to catalog number.)See Optional Features Section for other available options.

% ^ )

Valve Parts in Contact with FluidsBody Brass

Disc NBR

Seals PTFE & NBR




Piston Stainless Steel or Brass

Shading Coil Copper

Construction


Insulation


DCWatts


WattsVA

HoldingVA

Inrush AC DC AC DCF 11.6 6.1 16 30 238210 238710 238214 238714

F 16.8 16.1 35 95 272610 97617 272614 97617

F 22.6 - - - - 238710 - 238714

Standard Voltages: 24, 120, 240, 480 volts AC, 60 Hz (or 110, 220 volts AC, 50 Hz).6, 12, 24, 120, 240 volts DC. Must be specified when ordering.Other voltages are available when required.

Electrical

8221R2

2/2SERIES

8221 4

2-WAY

18


PipeSize(ins.)

OrificeSize(ins.)

CvFlow

Factor

Operating PressureDifferential (psi)

Max. FluidTemp. ˚F Brass Body

Const.Ref.


Min. �

Max. AC Max. DC

Water � Water � AC DC Catalog Number AC DCNORMALLY CLOSED (Closed when de-energized)

3/8 9/16 3 5 150 125 180 150 8221G001 1 6.1/F 11.6/F

1/2 9/16 3.5 5 150 125 180 150 8221G003 1 6.1/F 11.6/F

3/4 3/4 5.5 5 150 125 180 150 8221G005 2 6.1/F 11.6/F

1 1 11.5 5 150 125 180 150 8221G007 5 6.1/F 11.6/F

1 1/4 1 1/8 13 5 150 125 180 150 8221G009 6 6.1/F 11.6/F

1 1/2 1 1/4 24 5 150 125 180 150 8221G011 7 6.1/F 11.6/F

2 1 3/4 36 5 150 125 180 150 8221G013 11 6.1/F 22.6/F

2 1/2 1 3/4 38 5 150 125 180 150 8221G015 12 6.1/F 22.6/F


3/8 9/16 3 5 - 125 - 150 8221 021 15 - 16.8/F

3/8 9/16 3 5 150 - 180 - 8221G021 3 16.1/F -

1/2 9/16 3.5 5 - 125 - 150 8221 023 15 - 16.8/F

1/2 9/16 3.5 5 150 - 180 - 8221G023 3 16.1/F -

3/4 3/4 5.5 5 - 125 - 150 8221 025 16 - 16.8/F

3/4 3/4 5.5 5 150 - 180 - 8221G025 4 16.1/F -

1 1 11.5 5 - 125 - 150 8221 027 17 - 16.8/F

1 1 11.5 5 150 - 180 - 8221G027 8 16.1/F -

1 1/4 1 1/8 13 5 - 125 - 150 8221 029 18 - 16.8/F

1 1/4 1 1/8 13 5 150 - 180 - 8221G029 9 16.1/F -

1 1/2 1 1/4 24 5 - 125 - 150 8221 031 19 - 16.8/F

1 1/2 1 1/4 24 5 150 - 180 - 8221G031 10 16.1/F -

2 1 3/4 36 5 - 125 - 150 8221 033 20 - 16.8/F

2 1 3/4 36 5 150 - 180 - 8221G033 13 16.1/F -

2 1/2 1 3/4 38 5 - 125 - 150 8221 035 21 - 16.8/F

2 1/2 1 3/4 38 5 150 - 180 - 8221G035 14 16.1/F

� Valves require a 5 psi Minimum Pressure Differential to open. Once open, they remain open with 3 psi differential pressure.� Refer to Steam/Hot Water Valve Series for Hot Water constructions. � On 50 hertz service, the watt rating for the 6.1/F solenoid is 8.1 watts.

8221R2

2/2SERIES

82214 2-W

AY

19


PipeSize(ins.)

OrificeSize(mm)

Kv FlowFactor(m3/h)

Operating PressureDifferential (bar)

Max. FluidTemp. ˚C Brass Body

Const.Ref.

Watt Rating/Class of Coil Insulation �

Min. �

Max. AC Max. DC

Water � Water � AC DC Catalog Number AC DCNORMALLY CLOSED (Closed when de-energized)

3/8 14 2.6 0.3 10 9 82 65 8221G001 1 6.1/F 11.6/F

1/2 14 3.0 0.3 10 9 82 65 8221G003 1 6.1/F 11.6/F

3/4 19 4.7 0.3 10 9 82 65 8221G005 2 6.1/F 11.6/F

1 25 9.9 0.3 10 9 82 65 8221G007 5 6.1/F 11.6/F

1 1/4 29 11 0.3 10 9 82 65 8221G009 6 6.1/F 11.6/F

1 1/2 32 21 0.3 10 9 82 65 8221G011 7 6.1/F 11.6/F

2 44 31 0.3 10 9 82 65 8221G013 11 6.1/F 22.6/F

2 1/2 44 33 0.3 10 9 82 65 8221G015 12 6.1/F 22.6/F


3/8 14 2.6 0.3 - 9 - 65 8221 021 15 - 16.8/F

3/8 14 2.6 0.3 10 - 82 - 8221G021 3 16.1/F -

1/2 14 3.0 0.3 - 9 - 65 8221 023 15 - 16.8/F

1/2 14 3.0 0.3 10 - 82 - 8221G023 3 16.1/F -

3/4 19 4.7 0.3 - 9 - 65 8221 025 16 - 16.8/F

3/4 19 4.7 0.3 10 - 82 - 8221G025 4 16.1/F -

1 25 9.9 0.3 - 9 - 65 8221 027 17 - 16.8/F

1 25 9.9 0.3 10 - 82 - 8221G027 8 16.1/F -

1 1/4 29 11 0.3 - 9 - 65 8221 029 18 - 16.8/F

1 1/4 29 11 0.3 10 - 82 - 8221G029 9 16.1/F -

1 1/2 32 21 0.3 - 9 - 65 8221 031 19 - 16.8/F

1 1/2 32 21 0.3 10 - 82 - 8221G031 10 16.1/F -

2 44 31 0.3 - 9 - 65 8221 033 20 - 16.8/F

2 44 31 0.3 10 - 82 - 8221G033 13 16.1/F -

2 1/2 44 33 0.3 - 9 - 65 8221 035 21 - 16.8/F

2 1/2 44 33 0.3 10 - 82 - 8221G035 14 16.1/F -

� Valves require a 0.3 bar Minimum Pressure Differential to open. Once open, they remain open with 0.2 bar differential pressure.� Refer to Steam/Hot Water Valve Series for Hot Water constructions.� On 50 hertz service, the watt rating for the 6.1/F solenoid is 8.1 watts.

8221R2

2/2SERIES

8221 4

2-WAY

20


Const. Ref. 3, 4Const. Ref. 1, 2

Const. Re. 7, 11, 12

Const. Ref. 8, 9, 10, 13, 14 Const. Ref. 15, 16

Const. Ref. 17 - 21


1ins. 4.34 2.69 2.72 3.59 3.41

mm 110 68 69 91 87

2ins. 4.53 2.85 2.78 3.75 3.41

mm 115 72 71 95 87

3ins. 5.22 3.14 2.72 4.47 3.69

mm 133 80 69 114 94

4ins. 5.41 3.30 2.78 4.62 3.69

mm 137 84 71 117 94

5ins. 5.62 3.15 3.75 4.03 3.16

mm 143 80 95 102 80

6ins. 5.56 3.15 3.66 4.03 3.56

mm 141 80 93 102 90

7ins. 6.12 3.30 4.38 4.19 4.12

mm 156 84 111 106 105

8ins. 6.53 3.59 3.75 4.91 3.16

mm 166 91 95 125 80

9ins. 6.47 3.59 3.56 4.91 3.56

mm 164 91 93 125 90

10ins. 7.03 3.74 4.38 5.06 4.12

mm 179 95 111 129 105

11ins. 7.38 3.71 5.06 4.59 4.72

mm 188 94 129 117 120

12ins. 7.38 3.71 5.50 4.59 5.19

mm 188 94 140 117 132

13ins. 8.22 4.15 5.06 5.47 4.72

mm 209 105 129 139 120

14ins. 8.22 4.15 5.50 5.47 5.19

mm 209 105 140 139 132

15ins. 5.22 - 2.72 4.47 3.69

mm 133 - 69 114 94

16ins. 5.41 - 2.78 4.62 3.69

mm 137 - 71 117 94

17ins. 6.53 - 3.75 4.91 3.16

mm 166 - 95 125 80

18ins. 6.47 - 3.66 4.91 3.56

mm 164 - 93 125 90

19ins. 7.03 - 4.38 5.06 4.12

mm 179 - 111 129 105

20ins. 8.22 - 5.06 5.47 4.72

mm 209 - 129 139 120

21ins. 8.22 - 5.50 5.47 5.19

mm 209 - 140 139 132

IMPORTANT: Valves may be mounted inany position.

L W

1/2 NPT

H

P

K

Const. Ref. 5, 6

8221R2

2/2SERIES

82564 2-W

AY

1


General Purpose NSF

Body Brass 316 Stainless Steel 316 Stainless Steel

Core Tube/Bonnet S.S. / Plated Steel S.S. / S.S. S.S. / S.S.

Core and Plugnut Stainless Steel

Springs Stainless Steel

Seals and Disc FKM EPDM


1 2

Features• 2-way normally closed operation

• Compact design

• Brass and 316 stainless steel body constructions

• Mountable in any position

• Available with manual operator

• NSF 61 and 169 version available for potable waterand food service

Solenoid Enclosures

Construction

Direct ActingSubminiature Solenoid Valves

1/8" and 1/4" NPT

Prefix

StandardCoil and Class of

Insulation

Watt Rating andPower Consumption

AmbientTemp.˚F

Spare Coil FamilyDCWatts

AC

WattsVA

HoldingVA

Inrush AC DCU F 6.9 6.3 8.8 12.1 15 to 140 400115 400115

SC F 6.9 6.3 8.8 12.1 15 to 140 400125 400125

Standard voltages: 24,120, 240 volts AC, 50-60 Hz. 12, 24, 120 volts DC Must be specified when ordering.

2

1

NC

Standard: Open frame (Prefix U) 18" leadsOptional: DIN (size 11mm, form B) (Prefix SC). Watertight/IP-65 when used with DIN connector kit for SC coils (see kits below).

ApprovalsUL recognized coil - File MH28173CSA recognized coil - see CSA certificate No. 235748Meets applicable CE directivesNSF 61 - Drinking water system componentsNSF 169 - Special purpose food

Equipment and DevicesThe NSF Certification Program is accredited by the Standards Council of Canada and ANSI.

1/2" NPT conduit hub kit for leaded coils 224735-001-*(Kit contains 10 pcs of each: threaded hub, gasket, and attaching screw.)DIN connector kit for SC coils 226061-001-*(Kit contains 10 pcs of each: connector, gasket, and attaching screw.)Mounting adapter kit 289719 (Kit contains 2 screws and plate.)

Kits

Electrical

% )ANSI Accredited ProgramPRODUCT CERTIFICATION

8256_NSFR1

2/2SERIES

8256 4

2-WAY

2

Specifications (English Units)

PipeSize(ins.)

OrificeSize(ins.)

CvFlow

Factor

Operating Pressure Differential (psi)Max.Fluid

Temp.˚F

Brass Stainless SteelConst.Ref.

Wattage

Approx. ShippingWeight(lbs.)

Max. AC � Max. DC �

Air - InertGas Water

Light Oil @ 300 SSU


Light Oil @ 300 SSU AC DC AC DC

General Service - Normally Closed

1/8 3/64 0.05 500 500 400 360 360 330 180 180 U8256A001V U8256A013V 1 6.3 6.9 0.5

1/8 1/16 0.08 400 390 230 220 220 220 180 180 U8256A002V U8256A014V 1 6.3 6.9 0.5

1/8 3/32 0.15 180 180 105 90 90 90 180 180 U8256A004V U8256A016V 1 6.3 6.9 0.5

1/8 7/64 0.19 135 126 80 63 63 63 180 180 U8256B045V U8256B046V 2 6.3 6.9 0.6

NSF 61 and 169 Listed

1/8 3/32 0.15 - 200 - - 130 - 180 180 - U8256A103E 1 6.3 6.9 0.5

1/8 7/64 0.17 - 150 - - 100 - 180 180 - U8256A104E 2 6.3 6.9 0.6

1/4 3/32 0.15 - 200 - - 130 - 180 180 - U8256A107E 3 6.3 6.9 0.5

1/4 7/64 0.17 - 150 - - 100 - 180 180 - U8256A108E 3 6.3 6.9 0.6

� MS option limits max. pressures to 220 psi (unless limited by operating pressure).

PipeSize(ins.)

OrificeSize(mm)

Kv FlowFactor(m3/h)

Operating Pressure Differential (bar)Max.Fluid

Temp.˚C

Brass Stainless SteelConst.Ref.

Wattage

Approx. ShippingWeight(kgs.)

Max. AC � Max. DC �


Light Oil @ 300 SSU


Light Oil @ 300 SSU AC DC AC DC

General Service - Normally Closed

1/8 1.2 0.04 34 34 27 25 25 23 82 82 U8256A001V U8256A013V 1 6.3 6.9 0.22

1/8 1.6 0.07 27 27 16 15 15 15 82 82 U8256A002V U8256A014V 1 6.3 6.9 0.22

1/8 2.4 0.13 12 12 7 6 6 6 82 82 U8256A004V U8256A016V 1 6.3 6.9 0.22

1/8 2.7 0.16 9 8 5 4 4 4 82 82 U8256B045V U8256B046V 2 6.3 6.9 0.27

NSF 61 and 169 Listed

1/8 2.4 0.13 - 14 - - 9 - 82 82 - U8256A103E 1 6.3 6.9 0.22

1/8 2.7 0.16 - 10 - - 7 - 82 82 - U8256A104E 2 6.3 6.9 0.22

1/4 2.4 0.13 - 14 - - 9 - 82 82 - U8256A107E 3 6.3 6.9 0.22

1/4 2.7 0.16 - 10 - - 7 - 82 82 - U8256A108E 3 6.3 6.9 0.27

� MS option limits max. pressures to 15 bar (unless limited by operating pressure).

Specifications (Metric Units)

8256_NSFR1

2/2SERIES

82564 2-W

AY

3


Solenoid Options � Base Catalog Number Resilient Materials � Other Standard Rebuild Kit

NEM

A Ty

pe 3

-9

High

Tem

p. D

IN

Wiri

ng B

ox S

crew

Term

inal

Mul

tipin

DIN

Spad

e

Open

Fra

me

with

Lead

s

Bras

s

Stai

nles

s St

eel

FKM

EPDM

RUBY

Oxyg

en S

ervi

ce

PTFE

Uret

hane

Vacu

um

Man

ual O

pera

tor

Mou

ntin

g Br

acke

t

Bras

s AC

/DC

Stai

nles

s AC

/DC

- - - - SC - � U8256A001V U8256A013V � E - NV - - - MS - - -

- - - - SC - � U8256A002V U8256A014V � E - NV - - - MS - - -

- - - - SC - � U8256A004V U8256A016V � E - NV - - - MS - - -

- - - - SC - � U8256B045V U8256B046V � E - NV - - - MS - - -

- - - - SC - � - U8256A103E - � - - - - - MS - - -

- - - - SC - � - U8256A104E - � - - - - - MS - - -

- - - - SC - � - U8256A107E - � - - - - - MS - - -

- - - - SC - � - U8256A108E - � - - - - - MS - - -

� = Standard. � Replace V suffix. � Replace U prefix with SC prefix.

12E

.47(12)

.65(16)

.43(11)

.71(18)

C

1/8 NPT(NSF 1/8, 1/4 NPT)

D

.59(15)

.86(22)

A B

M3 - THROUGH HOLES

Shown with DIN coil without connector

Const.Ref. A B C D E

1ins. 1.81 2.08 1.29 1 0.59

mm 46 53 33 25 15

2ins 1.98 2.25 .984 1 0.59

mm 50 57 25 25 15

3ins. 1.86 2.25 1.73 1.12 .83

mm 46 57 44 28 21

Capabilities Chart

8256_NSFR1

2/2SERIES

8260

% & )Features• Corrosion-resistant plastic bodies

• Available with compression fitting ends for metal or plastic tube to save installation cost


• Dispensing vending construction NSF listed

Direct ActingPlastic Body Solenoid Valves

Hose Bib, Compression Connection or 1/4" Male Flare

NC

Solenoid Enclosures

Electrical

Nominal Ambient Temp. Range:AC: 32˚F to 125˚F (0˚C to 52˚C) DC: 32˚F to 104˚F (0˚C to 40˚C)Refer to Engineering Section for details.

Approvals:CSA certified. UL Recognized Component. Meetsapplicable CE directives.Refer to Engineering Section for details.

Construction

Standard: Watertight, Types 1, 2, 3, 3S, 4, and 4X.Optional: Open Frame Solenoid, Junction Box enclosures. See Optional Features Section for descriptions on these options.

4 2-W

AY

27

Valve Parts in Contact with FluidsBody CA, PA, PP

Seals and Disc NBR




Shading Coil Copper


Insulation

Watt Rating and Power ConsumptionSpare Coil Part

Number

DC Watts

AC General Purpose

WattsVA

Holding VA Inrush AC DCB 6.4 6.5 9.2 17.3 174879 180555

F 10.6 6.1 16 30 238210 238310

Standard Voltages: 24, 120, 240, 480 volts AC, 60 Hz (or 110, 220 volts AC, 50 Hz).6, 12, 24, 120, 240 volts DC. Must be specified when ordering.Other voltages available when required.

8260R1

2/2SERIES

8260 4

2-WAY

28


PipeConnections

OrificeSize(ins.)

Cv FlowFactor

Operating Pressure Differential (psi)Max. FluidTemp. ˚F Plastic Body

Watt Rating/Class of CoilInsulation �Max. AC Max. DC

Air-InertGas Water

Air-InertGas Water AC DC

CatalogNumber

Const.Ref. AC DC

GENERAL SERVICE CONSTRUCTION - CA Body, Watertight enclosure with leads

1/4" Male Flare 9/64 .35 120 120 50 50 130 120 8260G042 1 6.1/F 10.6/F

Bib for 1/4" I.D. Tube 9/64 .35 120 120 50 50 130 120 8260G054 2 6.1/F 10.6/F

1/4" O.D. � Compression 9/64 .35 120 120 50 50 130 120 8260G071 3 6.1/F 10.6/F

GENERAL SERVICE CONSTRUCTION - PP Body, Open Frame Solenoid and Spade Terminal Coils

1/4" O.D. � Compression

1/16 .09 150 150 60 60 130 120 USM8260 073 5 6.5/B 6.4/B

3/32 .19 100 100 20 20 130 120 USM8260 074 5 6.5/B 6.4/B

1/8 .31 60 60 10 10 130 120 USM8260 075 5 6.5/B 6.4/B

5/32 .43 35 35 5 5 130 120 USM8260 076 5 6.5/B 6.4/B

DISPENSING VENDING CONSTRUCTION - NSF Listed - PP Body, Open Frame Solenoid and Spade Terminal Coils


1/16 .09 150 150 60 60 130 120 USM8260 077 4 6.5/B 6.4/B

3/32 .19 100 100 20 20 130 120 USM8260 078 4 6.5/B 6.4/B

1/8 .31 60 60 10 10 130 120 USM8260 079 4 6.5/B 6.4/B

5/32 .43 35 35 5 5 130 120 USM8260 080 4 6.5/B 6.4/B

PA Body, Open Frame Solenoid and Spade Terminal Coils

3/8" O.D. � Compression 5/16 1.3 5 5 - - 130 - USM8260 089 6 6.5/B -

� Fittings not supplied with valve. To order, refer to Kit No. 224150 - plastic tubing, and Kit No. 224151 - metal tubing.� On 50 hertz service, the watt rating for the 6.1/F solenoid is 8.1 watts.

PipeConnections

OrificeSize(mm)

Kv FlowFactor(m3/h)

Operating Pressure Differential (bar)Max. FluidTemp. ˚C Plastic Body


Air-InertGas Water

Air-InertGas Water AC DC Catalog Number

Constr.Ref. AC DC

GENERAL SERVICE CONSTRUCTION - CA Body, Watertight enclosure with leads

1/4" Male Flare 3.6 .30 8.3 8.3 3.4 3.4 54 49 8260G042 1 6.1/F 10.6/F

Bib for 1/4" I.D. Tube 3.6 .30 8.3 8.3 3.4 3.4 54 49 8260G054 2 6.1/F 10.6/F

1/4" O.D. � Compression 3.6 .30 8.3 8.3 3.4 3.4 54 49 8260G071 3 6.1/F 10.6/F

GENERAL SERVICE CONSTRUCTION - PP Body, Open Frame Solenoid and Spade Terminal Coils


1.6 .08 10.3 10.3 4.1 4.1 54 49 USM8260 073 5 6.5/B 6.4/B

2.4 .16 6.9 6.9 1.4 1.4 54 49 USM8260 074 5 6.5/B 6.4/B

3.2 .27 4.1 4.1 0.7 0.7 54 49 USM8260 075 5 6.5/B 6.4/B

4.0 .37 2.4 2.4 0.3 0.3 54 49 USM8260 076 5 6.5/B 6.4/B

DISPENSING VENDING CONSTRUCTION - NSF Listed - PP Body, Open Frame Solenoid and Spade Terminal Coils


1.6 .08 10.3 10.3 4.1 4.1 54 49 USM8260 077 4 6.5/B 6.4/B

2.4 .16 6.9 6.9 1.4 1.4 54 49 USM8260 078 4 6.5/B 6.4/B

3.2 .27 4.1 4.1 0.7 0.7 54 49 USM8260 079 4 6.5/B 6.4/B

4.0 .37 2.4 2.4 0.3 0.3 54 49 USM8260 080 4 6.5/B 6.4/B

PA Body, Open Frame Solenoid and Spade Terminal Coils

3/8" O.D. � Compression 7.9 1.1 0.3 0.3 - - 54 - USM8260 089 6 6.5/B -

� Fittings not supplied with valve. To order, refer to Kit No. 224150 - plastic tubing, and Kit No. 224151 - metal tubing.� On 50 hertz service, the watt rating for the 6.1/F solenoid is 8.1 watts.


8260R1

2/2SERIES

82604 2-W

AY

29

Const. Ref. 1


Const. Ref. 2

Const. Ref. 3

8260R1

2/2SERIES

8260 4

2-WAY

30


0.44 (11.1) HEXAGON(BOTH ENDS)

(29.4)

(0.79)0.030.41

(10.3)(REF)

IC

(NOTE 1)

0.98(25.0)

1.97(50.0)

0.330.3(9.5)(20.6)

0.8

1.31

1.5(38.1)

1.28(32.5)

(25.4)2

1

4WIDE x

1

2THICK TERMINALS

.666

.333

.143 (3.6) DIA. HOLES x 0.31 (7.9) DEEP, (2) MOUNTING HOLES.

.4375−20 UNF−2A THREAD (BOTH ENDS)

116 ORIFICE SIZE SHOWN

.200

.475

.170 (4.3) DIA. HOLE(2 PLACES)

A. C. CONSTRUCTION SHOWN

FLOW

(3.33)

1

(50.8)

1.88

(47.6)

(8.3)

(16.9)

(8.4)

(5.0)

(12.1)

0.9 (22.2)

1.15

1

4

Const. Ref. 4

14

WIDE x 12

THICK TERMINALS

2 MOUNTING HOLES 11/32 DEEP,FOR NO. 10 THREADS CUTTING SCREW.6250-20 UN-2A THREAD

(BOTH ENDS)

(6) (0.8)

(Ø 8.7)

1132

1116

(8.7)

(17.5)

BODY SHOWN ONLY

1964

1932

(15.1)

(7.5)

2.43(62)

1.21(30.7)

1.31(33.3)

0.81 3.8(20.6)

(16)

1.1(27.8)

3(76)

0.44(11.1)

2(51)

1(25.4)

.326

(8.3)

(9.53)

38

FLOW

Const. Ref. 5

Const. Ref. 6

0.44 (11.1) HEXAGON(BOTH ENDS)

(29.4)

(0.79)0.030.41

(10.3)(REF)

IC

(NOTE 1)

0.98(25.0)

1.97(50.0)

0.330.3(9.5)(20.6)

0.8

1.31

1.5(38.1)

1.28(32.5)

(25.4)2

1

4WIDE x

1

2THICK TERMINALS

.666

.333

.143 (3.6) DIA. HOLES x 0.31 (7.9) DEEP, (2) MOUNTING HOLES.

.4375−20 UNF−2A THREAD (BOTH ENDS)

116 ORIFICE SIZE SHOWN

.200

.475

.170 (4.3) DIA. HOLE(2 PLACES)

A. C. CONSTRUCTION SHOWN

FLOW

(3.33)

1

(50.8)

1.88

(47.6)

(8.3)

(16.9)

(8.4)

(5.0)

(12.1)

0.9 (22.2)

1.15

(6) (0.8)

14

8260R1

2/2SERIES

82628263

% ^ # )Features• Welded core tube provides higher pressure ratings

• Reliable, proven design with high flows

• Small poppet valves for tight shutoff

• Wide range of elastomers for specialty service applications


• Tapped mounting holes in body standard

Direct Acting, Normally ClosedGeneral Service Solenoid Valves


NC

Solenoid Enclosures

Nominal Ambient Temp. RangesThe nominal limitation of 32°F (0°C) is advisable for anyvalve that might contain moisture (water vapor). AC: -13˚F to 131˚F (-25˚C to 55˚C)DC: -13˚F to 104˚F (-25˚C to 40˚C)

-13˚F to 131˚F (-25˚C to 55˚C)Note: Max ambient for explosionproof (EF) is 125˚F(52˚C) for AC, 131˚F (55˚C) for DC.Optional: For AC, the max. ambient temperature is 140˚F (60˚C) with Class H coil (with or without prefix EF)Refer to Engineering Section for details.

ApprovalsCSA certified. UL listed, as indicated. Safety ShutoffValves FM approved. Meets applicable CE directives.Refer to Engineering Section for details.

Construction

Standard: Watertight, Types 1, 2, 3, 3S, 4, and 4X.Optional: Explosionproof and Watertight, Types 3, 3S, 4, 4X, 6, 6P, 7, and 9.(To order, add prefix “EF” to catalog number)See Optional Features Section for other available options.

4 2-W

AY

31


Body Brass Cast 304 Stainless Steel

Seals and Discs NBR or Cast UR





Watt Rating andPower Consumption Spare Coil Part No.

DCWatts


WattsVA

Holding VA Inrush AC DC AC DC10.6 6.1* 16 30 238210 238510 238214 238514

18.6 9.1* 20 45 238210 238510 238214 238514

11.6 10.1 25 50 238610 238910 238614 238914

22.6 17.1 40 70 238610 238910 238614 238914

Standard Voltages: 24, 120, 240, 480 volts AC, 60 Hz (or 110, 220 volts AC, 50 Hz).6, 12, 24, 120, 240 volts DC. Must be specified when ordering.Other voltages available when required.*On 50 hertz service, the rating for the 6.1/F solenoid is 8.1 watts, andthe rating for the 9.1/F solenoid is 11.1 watts.

Electrical

OptionsMounting bracket (suffix MB)Quarter-turn manual operator with screw slot (suffix MS)Panel mount (prefix GP for conduit; consult ASCO for other electrical connections)Vacuum service (suffix VVM, VVH; see Vacuum Section for more details.)Oxygen service (suffix N)Silicone Free (suffix SF) Elastomers: Viton (suffix V), Ethylene Propylene (suffix E), Neoprene (suffix J), Teflon (suffix T), Low Temp NBR (suffix A)Note: For suffix A, Fluid temp. range -40˚F to 167˚F only for valves with 10.1, 17.1, 11.6, and 22.6 watt coils.Refer to Engineering Section for fluid and temperature compatibility.

2/2SERIES82628263 4

2-WAY

32


PipeSize(ins.)

Orificesize

(ins.)

CvFlow

Factor

Operating Pressure Differential (psi)Max. FluidTemp. °F

Catalog Number

Const.Ref.

ULListing

Watt Rating/Class of Coil

InsulationMax. AC@131°F Max. DC@104°F Max. DC@131°F

BrassStainless

SteelAir-Inert

Gas Water Lt. Oil @300ssu

Air-InertGas Water

Lt. Oil @300ssu

Air-InertGas Water

Lt. Oil300ssu AC DC AC DC

NORMALLY CLOSED (Closed when de-energized), NBR Disc 1/8 3/64 0.06 2200 2200 1700 - - - - - - 140 - - 8262H175 � 1 � 10.1/F -1/8 3/64 0.06 - - - 2000 2000 1725 1900 1900 1700 - 140 - 8262H176 � 1 � - 22.6/H1/8 3/64 0.06 - - - 1500 1500 1500 1500 1500 1500 - 140 8262H089 � - 1 � - 22.6/H1/8 3/64 0.06 2025 1710 825 965 745 720 920 700 675 140 140 - 8262H079 � 2 � 9.1/F 18.6/H1/8 3/64 0.06 1500 1350 825 750 620 565 700 565 530 140 140 8262H096 � - 2 � 6.1/F 10.6/H1/8 3/64 0.06 1500 1350 825 - - - - - - 140 - - 8262H173 � 2 � 6.1/F -1/8 3/64 0.06 1500 1500 1500 1170 1145 945 1000 965 855 140 140 8262H099 � - 1 � 10.1/F 11.6/H1/8 3/64 0.06 750 750 725 750 640 550 750 600 500 180 180 8262H001 8262H012 2 � 6.1/F 10.6/H1/8 3/32 0.21 720 410 410 610 410 410 600 410 400 180 180 8262H277 8262H178 1 � 17.1/F 22.6/H1/8 3/32 0.21 - - - 290 290 270 240 240 255 180 180 - 8262H177 1 � - 11.6/H1/8 3/32 0.21 500 350 325 295 210 205 285 200 195 180 180 8262H011 - 2 � 9.1/F 18.6/H1/8 3/32 0.21 370 330 190 235 160 160 215 150 145 180 180 8262H014 8262H015 2 � 6.1/F 10.6/H1/8 1/8 0.35 500 380 355 275 275 235 250 250 225 180 180 8262H105 8262H174 1 � 17.1/F 22.6/H1/8 1/8 0.35 340 300 215 - - - - - - - 180 - 8262H179 1 � 10.1/F -1/8 1/8 0.35 275 260 195 165 130 130 155 120 120 180 180 8262H016 - 2 � 9.1/F 18.6/H1/8 1/8 0.35 185 180 120 130 110 95 120 100 90 180 180 8262H002 8262H006 2 � 6.1/F 10.6/H1/4 3/64 0.06 2200 2200 1700 1170 1145 945 1000 965 855 140 140 - 8262H214 � 3 � 10.1/F 11.6/H1/4 3/64 0.06 1500 1500 1500 1170 1145 945 1000 965 855 140 140 8262H200 � - 3 � 10.1/F 11.6/H1/4 3/64 0.06 1500 1500 1500 1500 1500 1500 1500 1500 1500 140 140 8262H107 � - 3 � 17.1/F 22.6/H1/4 3/64 0.06 - - - 2000 2000 1725 1900 1900 1700 - 140 - 8262H181 � 3 � - 22.6/H1/4 3/64 0.06 1500 1350 825 750 620 530 700 565 495 140 140 8262H106 � 8262H180 � 4 � 6.1/F 10.6/H1/4 3/64 0.06 750 750 725 750 640 550 750 600 500 180 180 8262H019 8262H080 4 � 6.1/F 10.6/H1/4 3/32 0.21 720 410 410 610 410 410 600 410 400 180 180 8262H109 8262H183 3 � 17.1/F 22.6/H1/4 3/32 0.21 590 410 410 290 290 270 240 240 225 180 180 8262H108 8262H182 3 � 10.1/F 11.6/H1/4 3/32 0.21 500 350 270 295 210 205 285 200 195 180 180 8262H021 - 4 � 9.1/F 18.6/H1/4 3/32 0.21 370 330 160 235 160 160 215 150 145 180 180 8262H020 8262H086 4 � 6.1/F 10.6/H1/4 1/8 0.35 500 380 355 275 275 235 250 250 225 180 180 8262H110 8262H185 3 � 17.1/F 22.6/H1/4 1/8 0.35 340 300 215 130 125 115 110 105 100 180 180 8262H232 - 3 � 10.1/F 11.6/H1/4 1/8 0.35 340 300 215 - - - - - - 180 - - 8262H184 3 � 10.1/F -1/4 1/8 0.35 275 260 150 165 130 120 155 120 115 180 180 8262H023 - 4 � 9.1/F 18.6/H1/4 1/8 0.35 185 180 90 130 110 90 120 100 85 180 180 8262H022 8262H007 4 � 6.1/F 10.6/H1/4 5/32 0.52 300 210 210 135 135 135 115 115 115 180 180 8262H112 8262H187 3 � 17.1/F 22.6/H1/4 5/32 0.52 210 200 145 65 63 63 55 54 54 180 180 8262H202 - 3 � 10.1/F 11.6/H1/4 5/32 0.52 210 200 145 - - - - - - 180 180 - 8262H220 3 � 10.1/F -1/4 5/32 0.52 150 140 100 95 75 75 85 72 70 180 180 8262H113 - 4 � 9.1/F 18.6/H1/4 5/32 0.52 100 100 55 72 60 55 67 53 52 180 180 8262H111 8262H186 4 � 6.1/F 10.6/H1/4 7/32 0.73 125 125 125 70 70 70 65 65 65 180 180 8262H114 8262H188 3 � 17.1/F 22.6/H1/4 7/32 0.73 100 100 100 35 35 35 30 30 30 180 180 8262H208 - 3 � 10.1/F 11.6/H1/4 7/32 0.73 100 100 100 - - - - - - 180 - - 8262H226 3 � 10.1/F -1/4 7/32 0.73 55 54 40 38 33 31 35 30 28 180 180 8262H013 8262H036 4 � 6.1/F 10.6/H1/4 9/32 0.88 90 90 90 53 50 47 48 46 44 180 180 8262H212 8262H230 3 � 17.1/F 22.6/H1/4 9/32 0.88 65 75 60 25 25 22 22 22 20 180 180 8262H210 - 3 � 10.1/F 11.6/H1/4 9/32 0.88 65 75 60 - - - - - - 180 - - 8262H189 3 � 10.1/F -1/4 9/32 0.88 36 36 33 27 23 21 24 22 20 180 180 8262H090 8262H038 4 � 6.1/F 10.6/H3/8 1/8 0.35 500 380 355 275 275 160 250 250 150 180 180 8263H115 8263H191 5 � 17.1/F 22.6/H3/8 1/8 0.35 340 300 215 130 125 85 110 105 75 180 180 8263H232 - 5 � 10.1/F 11.6/H3/8 1/8 0.35 340 300 215 - - - - - - 180 - - 8263H190 5 � 10.1/F -3/8 1/8 0.35 275 260 140 165 130 110 155 120 105 180 180 8263H003 - 6 � 9.1/F 18.6/H3/8 1/8 0.35 185 180 90 130 110 80 120 100 75 180 180 8263H002 8263H330 6 � 6.1/F 10.6/H3/8 5/32 0.52 300 210 195 135 135 100 115 115 90 180 180 8263H118 8263H193 5 � 17.1/F 22.6/H3/8 5/32 0.52 210 185 100 65 63 50 55 54 44 180 180 8263H200 - 5 � 10.1/F 11.6/H3/8 5/32 0.52 210 185 100 - - - - - - 180 - - 8263H331 5 � 10.1/F -3/8 5/32 0.52 150 140 80 95 75 75 85 72 70 180 180 8263H117 - 6 � 9.1/F 18.6/H3/8 5/32 0.52 100 100 50 72 60 55 67 53 52 180 180 8263H116 8263H192 6 � 6.1/F 10.6/H3/8 7/32 0.73 125 100 100 70 70 70 65 65 65 180 180 8263H206 8263H332 5 � 17.1/F 22.6/H3/8 7/32 0.73 100 86 70 35 35 35 30 30 30 180 180 8263H124 - 5 � 10.1/F 11.6/H3/8 7/32 0.73 100 86 70 - - - - - - 180 - - 8263H195 5 � 10.1/F -3/8 7/32 0.73 55 54 29 38 33 31 35 30 28 180 180 8263H119 8263H194 6 � 6.1/F 10.6/H3/8 9/32 0.88 100 85 70 53 50 47 48 46 44 180 180 8263H210 8263H333 5 � 17.1/F 22.6/H3/8 9/32 0.88 65 63 47 - - - - - - 180 180 8263H125 8263H197 5 � 10.1/F -3/8 9/32 0.88 35 32 21 27 23 21 24 22 20 180 180 8263H054 8263H196 6 � 6.1/F 10.6/H

� Cast UR disc supplied as standard, limits min. ambient temp. to 32˚F (0˚C); � = General Purpose Valve, � = Safety Shutoff Valve

2/2SERIES

826282634 2-

WAY

33


PipeSize(ins.)

Orificesize

(mm)

KvFlow

Factor(m3/h)

Operating Pressure Differential (bar)Max. FluidTemp. °C

Catalog Number

Const.Ref.

ULListing

Watt Rating/Class of Coil

InsulationMax. AC@55°C Max. DC@40°C Max. DC@55°C

BrassStainless

SteelAir-Inert

Gas Water Lt. Oil @300ssu

Air-InertGas Water

Lt. Oil @300ssu

Air-InertGas Water

Lt. Oil300ssu AC DC AC DC

NORMALLY CLOSED (Closed when de-energized), NBR Disc 1/8 1.2 0.05 152 152 117 - - - - - - 60 - - 8262H175 � 1 � 10.1/F -1/8 1.2 0.05 - - - 138 138 119 131 131 117 - 60 - 8262H176 � 1 � - 22.6/H1/8 1.2 0.05 - - - 103 103 103 103 103 103 - 60 8262H089 � - 1 � - 22.6/H1/8 1.2 0.05 140 118 57 67 51 50 63 48 47 60 60 - 8262H079 � 2 � 9.1/F 18.6/H1/8 1.2 0.05 103 93 57 52 43 39 48 39 37 60 60 8262H096 � - 2 � 6.1/F 10.6/H1/8 1.2 0.05 103 93 57 - - - - - - 60 - - 8262H173 � 2 � 6.1/F -1/8 1.2 0.05 103 103 103 81 79 65 69 67 59 60 60 8262H099 � - 1 � 10.1/F 11.6/H1/8 1.2 0.05 52 52 50 52 44 38 52 41 34 82 82 8262H001 8262H012 2 � 6.1/F 10.6/H1/8 2.4 0.18 50 28 28 42 28 28 41 28 28 82 82 8262H277 8262H178 1 � 17.1/F 22.6/H1/8 2.4 0.18 - - - 20 20 19 17 17 18 - 82 - 8262H177 1 � - 11.6/H1/8 2.4 0.18 34 24 22 20 14 14 20 14 13 82 82 8262H011 - 2 � 9.1/F 18.6/H1/8 2.4 0.18 26 23 13 16 11 11 15 10 10 82 82 8262H014 8262H015 2 � 6.1/F 10.6/H1/8 3.2 0.30 34 26 24 19 19 16 17 17 16 82 82 8262H105 8262H174 1 � 17.1/F 22.6/H1/8 3.2 0.30 23 21 15 - - - - - - 82 - - 8262H179 1 � 10.1/F -1/8 3.2 0.30 19 18 13 11 9 9 11 8 8 82 82 8262H016 - 2 � 9.1/F 18.6/H1/8 3.2 0.30 13 12 8 9 8 7 8 7 6 82 82 8262H002 8262H006 2 � 6.1/F 10.6/H1/4 1.2 0.05 152 152 117 81 79 65 69 67 59 60 60 - 8262H214 � 3 � 10.1/F 11.6/H1/4 1.2 0.05 103 103 103 81 79 65 69 67 59 60 60 8262H200 � - 3 � 10.1/F 11.6/H1/4 1.2 0.05 103 103 103 103 103 103 103 103 103 60 60 8262H107 � - 3 � 17.1/F 22.6/H1/4 1.2 0.05 - - - 138 138 119 131 131 117 - 60 - 8262H181 � 3 � - 22.6/H1/4 1.2 0.05 103 93 57 52 43 37 48 39 34 60 60 8262H106 � 8262H180 � 4 � 6.1/F 10.6/H1/4 1.2 0.05 52 52 50 52 44 38 52 41 34 82 82 8262H019 8262H080 4 � 6.1/F 10.6/H1/4 2.4 0.18 50 28 28 42 28 28 41 28 28 82 82 8262H109 8262H183 3 � 17.1/F 22.6/H1/4 2.4 0.18 41 28 28 20 20 19 17 17 16 82 82 8262H108 8262H182 3 � 10.1/F 11.6/H1/4 2.4 0.18 34 24 19 20 14 14 20 14 13 82 82 8262H021 - 4 � 9.1/F 18.6/H1/4 2.4 0.18 26 23 11 16 11 11 15 10 10 82 82 8262H020 8262H086 4 � 6.1/F 10.6/H1/4 3.2 0.30 34 26 24 19 19 16 17 17 16 82 82 8262H110 8262H185 3 � 17.1/F 22.6/H1/4 3.2 0.30 23 21 15 9 9 8 8 7 7 82 82 8262H232 - 3 � 10.1/F 11.6/H1/4 3.2 0.30 23 21 15 - - - - - - 82 - - 8262H184 3 � 10.1/F -1/4 3.2 0.30 19 18 10 11 9 8 11 8 8 82 82 8262H023 - 4 � 9.1/F 18.6/H1/4 3.2 0.30 13 12 6 9 8 6 8 7 6 82 82 8262H022 8262H007 4 � 6.1/F 10.6/H1/4 4.0 0.45 21 14 14 9 9 9 8 8 8 82 82 8262H112 8262H187 3 � 17.1/F 22.6/H1/4 4.0 0.45 14 14 10 4 4 4 4 4 4 82 82 8262H202 - 3 � 10.1/F 11.6/H1/4 4.0 0.45 14 14 10 - - - - - - 82 - - 8262H220 3 � 10.1/F -1/4 4.0 0.45 10 10 7 7 5 5 6 5 5 82 82 8262H113 - 4 � 9.1/F 18.6/H1/4 4.0 0.45 7 7 4 5 4 4 5 4 4 82 82 8262H111 8262H186 4 � 6.1/F 10.6/H1/4 5.6 0.63 9 9 9 5 5 5 4 4 4 82 82 8262H114 8262H188 3 � 17.1/F 22.6/H1/4 5.6 0.63 7 7 7 2 2 2 2 2 2 82 82 8262H208 - 3 � 10.1/F 11.6/H1/4 5.6 0.63 7 7 7 - - - - - - 82 - - 8262H226 3 � 10.1/F -1/4 5.6 0.63 4 4 3 3 2 2 2 2 2 82 82 8262H013 8262H036 4 � 6.1/F 10.6/H1/4 7.1 0.76 6 6 6 4 3 3 3 3 3 82 82 8262H212 8262H230 3 � 17.1/F 22.6/H1/4 7.1 0.76 4 5 4 2 2 2 2 2 1 82 82 8262H210 - 3 � 10.1/F 11.6/H1/4 7.1 0.76 4 5 4 - - - - - - 82 - - 8262H189 3 � 10.1/F -1/4 7.1 0.76 2 2 2 2 2 1 2 2 1 82 82 8262H090 8262H038 4 � 6.1/F 10.6/H3/8 3.2 0.30 34 26 24 19 21 11 17 19 10 82 82 8263H115 8263H191 5 � 17.1/F 22.6/H3/8 3.2 0.30 23 21 15 9 9 6 8 7 5 82 82 8263H232 - 5 � 10.1/F 11.6/H3/8 3.2 0.30 23 21 15 - - - - - - 82 82 - 8263H190 5 � 10.1/F -3/8 3.2 0.30 19 18 10 11 9 8 11 8 7 82 82 8263H003 - 6 � 9.1/F 18.6/H3/8 3.2 0.30 13 12 6 9 8 6 8 7 5 82 82 8263H002 8263H330 6 � 6.1/F 10.6/H3/8 4.0 0.45 21 14 13 9 9 7 8 8 6 82 82 8263H118 8263H193 5 � 17.1/F 22.6/H3/8 4.0 0.45 14 13 7 4 4 3 4 4 3 82 82 8263H200 - 5 � 10.1/F 11.6/H3/8 4.0 0.45 14 13 7 - - - - - - 82 - - 8263H331 5 � 10.1/F -3/8 4.0 0.45 10 10 6 7 5 5 6 5 5 82 82 8263H117 - 6 � 9.1/F 18.6/H3/8 4.0 0.45 7 7 3 5 4 4 5 4 4 82 82 8263H116 8263H192 6 � 6.1/F 10.6/H3/8 5.6 0.63 9 7 7 5 5 5 4 4 4 82 82 8263H206 8263H332 5 � 17.1/F 22.6/H3/8 5.6 0.63 7 6 5 2 2 2 2 2 2 82 82 8263H124 - 5 � 10.1/F 11.6/H3/8 5.6 0.63 7 6 5 - - - - - - 82 - - 8263H195 5 � 10.1/F -3/8 5.6 0.63 4 4 2 3 2 2 2 2 2 82 82 8263H119 8263H194 6 � 6.1/F 10.6/H3/8 7.1 0.76 7 6 5 4 3 3 3 3 3 82 82 8263H210 8263H333 5 � 17.1/F 22.6/H3/8 7.1 0.76 4 4 3 - - - - - - 82 - 8263H125 8263H197 5 � 10.1/F -3/8 7.1 0.76 2 2 1 2 2 1 2 2 1 82 82 8263H054 8263H196 6 � 6.1/F 10.6/H

� Cast UR disc supplied as standard, limits min. ambient temp. to 32˚F (0˚C); � = General Purpose Valve, � = Safety Shutoff Valve

2/2SERIES82628263 4

2-WAY

34



1ins 3.05 1.71 1.19 2.69 1.95mm 77 43 30 68 50

2ins 2.85 1.60 1.19 2.50 1.69mm 72 41 30 63 43

3ins 3.12 1.79 1.56 2.76 1.95mm 79 45 40 70 50

4ins 2.96 1.72 1.56 2.60 1.69mm 75 44 40 66 43

5ins 3.20 1.79 1.88 2.77 1.95mm 81 45 48 70 50

6ins 3.03 1.72 1.88 2.60 1.69mm 77 44 48 66 43

ANPT PIPE THREAD(2 PLACES)

K

P

L

H

W

Const. Ref. 1-6

Mounting Dimensions

.34[9]

.87[22.2]

.87[22.2]

.75[19]

.57[14]

.81[20.6]

.30[8]

.59[15]

.69[18]

FLOW

M5 THREAD.30 [7.6] MIN.FULL THREAD DEPTH2 HOLES FOR MOUNTING

MOUNTINGHOLES

MOUNTINGHOLES

FLOW

M5 THREAD.24 [6] MIN. FULL THREAD DEPTH2 HOLES FOR MOUNTING

MOUNTINGHOLES

MOUNTINGHOLES

FLOW

M5 THREAD.25 [6.4] MIN.FULL THREAD DEPTH.2 HOLES FOR MOUNTING

MOUNTING HOLES

MOUNTING HOLES

Const. Ref. 1, 2(1/8" Pipe)



Note: Mounting holes will accept a standard #10-32 machine screw.

2/2SERIES

8262

% ^ )Features• Reliable, proven design with high flows

• Small poppet valves for tight shutoff

• Wide range of elastomers for specialty service


• Brass and stainless steel constructions

Direct Acting, Normally OpenGeneral Service Solenoid Valves


NO

Solenoid EnclosuresNominal Ambient Temp. RangesAC: 32˚F to 125˚F (0˚C to 52˚C) DC: 32˚F to 104˚F (0˚C to 40˚C)Refer to Engineering Section for details.

ApprovalsCSA certified. UL listed, as indicated. Meets applicable CE directives.Refer to Engineering Section for details.

Construction

Standard: Watertight, Types 1, 2, 3, 3S, 4, and 4X.Optional: Explosionproof and Watertight, Types 3, 3S, 4, 4X, 6, 6P, 7, and 9.(To order, add prefix “EF” to catalog number)See Optional Features Section for other available options.

4 2-W

AY

35


Body Brass 303/304 Stainless Steel

Seals and Discs NBR or Cast UR





Stem CA / PA


Insulation


DCWatts


WattsVA

HoldingVA

Inrush AC DC AC DCF 10.6 6.1 16 30 238210 238310 238214 238314

F 11.6 10.1 25 50 238610 238710 238614 238714

Standard Voltages: 24, 120, 240, 480 volts AC, 60 Hz (or 110, 220 volts AC, 50 Hz).6, 12, 24, 120, 240 volts DC. Must be specified when ordering.Other voltages available when required.

Electrical

2/2SERIES8262 4

2-WAY

36


PipeSize(ins.)

OrificeSize(ins.)

CvFlow

Factor

Operating Pressure Differential (psi)Max. FluidTemp. ˚F Brass Body Stainless Steel Body


Air-InertGas Water

Lt. Oil@ 300SSU

Air-InertGas Water

Lt. Oil@ 300SSU AC DC

CatalogNumber

Const.Ref.

UL �Listing

CatalogNumber

Const.Ref.

UL �Listing AC DC

NORMALLY OPEN (Open when de-energized), NBR Disc (except where noted)

1/8 1/16 .09 500 300 225 400 250 150 180 120 8262G091 2 � 8262G092 2 � 6.1/F 10.6/F

1/8 3/32 .15 275 200 150 190 110 110 180 120 8262G093 2 � 8262G094 2 � 6.1/F 10.6/F

1/8 1/8 .21 125 100 85 80 60 50 180 120 8262G031 2 � 8262G035 2 � 6.1/F 10.6/F

1/4 3/64 .06 750 700 700 500 500 500 140 140 8262G260 � 3 � 8262G130 � 4 � 10.1/F 11.6/F

1/4 3/32 .17 300 250 230 200 150 125 140 140 8262G261 � 3 � 8262G134 � 4 � 10.1/F 11.6/F

1/4 1/8 .35 130 110 100 80 60 60 180 150 8262G262 3 � 8262G138 4 � 10.1/F 11.6/F

1/4 5/32 .49 85 75 60 45 30 30 180 150 8262G263 1 � 8262G142 4 � 10.1/F 11.6/F

1/4 7/32 .83 45 45 40 25 20 20 180 150 8262G264 1 � 8262G148 4 � 10.1/F 11.6/F

1/4 9/32 .96 30 25 20 15 15 15 180 150 8262G265 1 � 8262G152 4 � 10.1/F 11.6/F

� Cast UR disc supplied as standard.� On 50 hertz service, the rating for the 6.1/F solenoid is 8.1 watts.� � Safety Shutoff Valve; � General Purpose Valve. Refer to Engineering Section (Approvals) for details.

2/2SERIES

82624 2-W

AY

37


PipeSize(ins.)

OrificeSize(mm)

Kv FlowFactor(m3/h)

Operating Pressure Differential (bar) Max.Fluid

Temp. ˚C Brass Body Stainless Steel Body


Air-InertGas Water

Lt. Oil @ 300SSU

Air-InertGas Water

Lt. Oil @ 300SSU AC DC

CatalogNumber

Const.Ref.

UL �Listing

CatalogNumber

Const.Ref.

UL �Listing AC DC

NORMALLY OPEN (Open when de-energized), NBR Disc (except where noted)

1/8 1.6 .08 34 21 16 28 17 10 82 49 8262G091 2 � 8262G092 2 � 6.1/F 10.6/F

1/8 2.4 .13 19 14 10 13 8 8 82 49 8262G093 2 � 8262G094 2 � 6.1/F 10.6/F

1/8 3.2 .18 9 7 6 6 4 3 82 49 8262G031 2 � 8262G035 2 � 6.1/F 10.6/F

1/4 1.2 .05 52 48 48 34 34 34 60 60 8262G260 � 3 � 8262G130 � 4 � 10.1/F 11.6/F

1/4 2.4 .15 21 17 16 14 10 9 60 60 8262G261 � 3 � 8262G134 � 4 � 10.1/F 11.6/F

1/4 3.2 .30 9 8 7 6 4 4 82 65 8262G262 3 � 8262G138 4 � 10.1/F 11.6/F

1/4 4.0 .42 6 5 4 3 2 2 82 65 8262G263 1 � 8262G142 4 � 10.1/F 11.6/F

1/4 5.6 .71 3 3 3 2 1 1 82 65 8262G264 1 � 8262G148 4 � 10.1/F 11.6/F

1/4 7.1 .82 2 2 1 1 1 1 82 65 8262G265 1 � 8262G152 4 � 10.1/F 11.6/F

� Cast UR disc supplied as standard.� On 50 hertz service, the rating for the 6.1/F solenoid is 8.1 watts.� � Safety Shutoff Valve; � General Purpose Valve. Refer to Engineering Section (Approvals) for details.

2/2SERIES8262 4

2-WAY

38


Const. Ref. 4

.44 [11]

.44[11]

.09 [2.3]FOR MOUNTING2 PLACES

2 MOUNTING HOLESFOR .164 [4] THREADCUTTING SCREW

.09 [2.3] 2 PLACES K

P

H

L

FLOW

1/2 NPT W

1/8 NPTBOTH ENDS

.64 [16]1.30 [33]

Const. Refs. 2

Const. Ref. 1, 3

MOUNTING HOLESIN VALVE BODY

BRASS - CONST. REF. 1, 3CONST. REF. 4

CONST. REF.BRASS: 1, 3, 4S.S: 4

MOUNTING BRACKET

Mounting Details


1ins. 3.20 1.78 1.56 2.79 1.95mm 81 45 40 71 50

2ins. 3.15 1.32 1.19 2.18 1.69mm 80 34 30 55 43

3ins. 3.23 1.67 1.25 2.81 1.95mm 82 42 32 71 50

4ins. 3.16 1.65 1.56 2.79 1.95mm 80 42 40 71 50

IMPORTANT: Valves may be mounted in any position.

Documents

4 2-Way/2 Position Valves 2-WAY - Tri-State · PDF file2-Way/2 Position Valves Flow Diagrams ... Seals and Disc NBR Core Tube 305 Stainless Steel Core and ... 8215 2-WAY Features