4 Drawer dresser (5522) - Assembly and Operation Manual

Congratulations on purchasing an MDB Family product. This product will provide many years of service if you adhere to the following guidelines for assembly, maintenance and operation. This product is for residential use only. Any institutional use is strictly prohibited.

Please be sure to follow the instructions for proper assembly. Use a Phillips head screwdriver for assembling the product in addition to the Allen wrench included in the hardware box. Do not use power screwdrivers. All of our products are made from natural woods. Please understand that natural woods have color variations which are the result of nature and not defects in workmanship.

DO NOT SUBSTITUTE PARTS. ALL MODELS HAVE THE SAME QUANTITY OF PARTS AND HARD-WARE. YOUR MODEL MAY LOOK DIFFERENT FROM THE ONE ILLUSTRATED DUE TO STYLIS-TIC VARIATIONS.

page 1revised 26NOV2014

HARDWARE

Tools Needed(not included)

Phillipsscrewdriver

H8. Right Panel Glide (4) H10. Right Drawer Glide (4)

H11. Left Drawer Glide (4)H9. Left Panel Glide (4)

H2. Cam LockBolt (8)

H3. Cam Lock (8) H4.Knob (8)H1. 1-1/8” MachineBolt (22)

H12. Leg WoodScrew (8)

H7. Large Wood Screw (16)

H6. Small Wood Screw (100)

H5. Knob Bolt (8)

H13. Support BarFastener (8)

PARTS

page 2

(D)Back Panel x 2

(Q)Back Support Bar x 1

B. LeftEnd

Panel

A. RightEnd

Panel E. Dresser Top

J. Right Drawer Panel (4)

K. Left Drawer Panel (4)

M. Front Drawer Panel (4)

O. Back Drawer Panel (4)

D. Back Panel (2)N. Base Panel

C. DrawerBottom

Board (4)

P1. Leftleg (2)

P2. Rightleg (2)

G. Top Support Frame

F. Bottom Support Frame

H. Support Bar (3)

Q. Back Support Bar

H14. Wood Dowel (4)

H15. Plastic Plug (4) H15.Capuchon en

plastique (4)

(Q)

(H)(Q)to the Ieft and right

Step 1: Installing the Rail Glides

Step 2: Assemble Dresser End Panels, Support Frames and Support Bars

Installing the panel glides.

BA

Install the panel glides (H8) and (H9) onto the end panels (A) and (B). Use 3 wood screws (H6) for each glide.

DO NOT OVER TIGHTEN.

Assemble dresser end panels, support frames and support bars.

Make sure top support frame (G) is placed with counter-sunk holes facing down.

Use screws (H6) and support bar fastener (H13) to mount support bars (H) and (Q) to the left and right end panels (A) and (B).

Place bottom frame support frame (F) with counter-sunk holes facing up.

DO NOT OVER TIGHTEN.

page 3

1

2

(H6)(H6)

(H6) (H6)(H6)

(H6)

(H6) (H6)

(H6)(H6)

Step 3:Assemble Dresser Top

Assemble Base and Legs.Use 8 (H12) wood screws to install legs (P).

Assemble dresser top.Use 8 bolts (H1) to install the dresser top (E).

DO NOT OVER TIGHTEN.

There are no pre-drilled holes on base panel for H12. Align carefully and secure legs. Then attach base panel assembly to the dresser assembly using 6 (H1) machine bolts as shown in the picture.

Drawer AssemblyStep 6A.

page 4

H14

3 4 Back Panel Assembly.Use 12 screws (H6) for back panel.

5 6

(H14)

(H14)(H14)

(H14)

(H15)

(H15)

(H15)

(H15)(H15)

This item has a manufacturer’s limited one year warranty. Visit our web site at www.themdbfamily.com for more information.

Drawer AssemblyStep 6B. Drawer Assembly

Step 6C.

Drawer AssemblyStep 6D.

Drawer AssemblyStep 6E.

Drawer AssemblyStep 6F.

Insert the assembled drawers.

page 5

7

8

Serious or fatal crushing can occur when furniture tips over on children. To help prevent tip-over, follow the steps below to install this anti-tipping strap.

FURNITURE ANTI-TIPPING KIT INSTALLATION

WARNING

Place heaviest item in the lowest drawers.

do not set TVs or other heavy objects on top of this product.Never allow children to climb or hang ondrawers, doors, or shelves.Never open more than one drawer at a time.(OR)Do not defeat or remove the drawer interlocksystem.

Use of tip-over restraints may only reduce,but not eliminate, the risk of tip-over.This is permanent label. Do not attempt to remove!

Unless specifically designed to accommodate,

Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over:

Phillipsscrewdriver

Tools Needed (not included)

PencilStubby

Screwdriver

X 2X 1 X 1

X 1

page 6

Locate a 2” x 4” stud behind the wall, and make a mark.

8a2” x 4” wall stud

8bInstall the strap on the wall with long screw and washer.

8cInstall the other end of strap on the back of dresser with short screw and washer into the wood framing of the dresser.

Finish

KEEP THIS MANUAL IN A SAFEPLACE FOR FUTURE REFERENCE.

READ ALL INSTRUCTIONS BEFORE USING THE PRODUCT. KEEP THE

INSTRUCTIONS FOR FUTURE USE.

page 7

Safety Notes:• Do not allow your children to climb or jump on the furniture or in the drawer. Climbing on the furniture could make it top-heavy and cause the furniture to damage or tip over.• Never move or push heavy furniture by yourself as it can cause the furniture to tip over.• This furniture is not intended to support TV or other heavy items.• Do not overload the drawers.

There are no pre-drilled holes on base panel for H12. Align carefully and secure legs. Then attach base panel assembly to the dresser assembly using 6 (H1) machine bolts as shown in the picture.