7301 to 7310.29.00

Tariff Description

===========================================================================

Item 50 applies unless otherwise stated.

7302.10 RAILS, flat bottom, less than 20 kg/m

Op. 21.02.1984 Dec. 21.02.1984 - TC 8341714

7302.10 RAILS, crane, railway type, weight EXCEEDING 70 kg/m

Op. 14.06.1988 Dec. 18.08.1988 - TC 8805556

7302.10.00 RAIL, CONSTRUCTION, conforming to European Standard EN 14811,

being ANY of the following:

(a) 73C1;

(b) 75C1;

(c) 76C1;

(d) 105C1;

(e) 310C1

Op. 20.11.2015 Dec. 11.02.2016 - TC 1542183

7302.10.00 RAIL, GROOVED, conforming to European Standard EN 14811, being

ANY of the following:

(a) RI53-10;

(b) RI55NK;

(c) 51R1;

(d) 53R1;

(e) 54G2;

(f) 55G1;

(g) 55G2;

(h) 57R1;

(i) 59R1;

(j) 59R2;

(k) Ri60NL;

(l) 60R1;

(m) 60R2;

(n) 60R3;

(o) 62R1;

(p) 62R2;

(q) 63R1;

(r) 67R1

Op. 27.10.2015 Dec. 18.01.2016 - TC 1540089

7302.10.00 RAIL, grooved, being ANY of the following:

(a) Ri57A;

(b) 57A

(c) Ri60R1;

(d) Ri60;

(e) Ri60-10;

(f) 60Ri1;

(g) 60R1

Op. 09.07.2010 Dec. 29.09.2010 - TC 1031338

7302.10.00 RAIL TRACK, comprising NOT less than 0.84% carbon

Op. 10.08.2005 Dec. 28.10.2005 - TC 0510522

7302.10.00 RAIL, having ALL of the following:

(a) elevated guardrail configuration;

(b) overall height 93 mm;

(c) rail head height 38 mm;

(d) neck height 40 mm;

(e) base (foot) height 15 mm;

(f) rail head width 80 mm;

(g) base (foot) width 40 mm

Op. 22.06.1998 Dec. 28.08.1998 - TC 9805404

7302.30.00 RAIL, ASYMMETRICAL POINTS, having ALL of the following:

(a) tongue rail configuration;

(b) base width 140 mm;

(c) overall height 134 mm;

Tariff Description

===========================================================================


(d) rail head width 74.5 mm;

(e) rail head height 53 mm;

(f) neck height 47.3 mm

Op. 09.04.1998 Dec. 10.06.2010 - TC 1025922

7302.90.00 CLIPS, CRANE RAIL

Op. 05.06.2008 Dec. 22.08.2008 - TC 0811455

7303.00.00 PIPES, cast iron, complying with European Standard EN877:1999

(EN877:1999) having EITHER of the following:

(a) internal coating of epoxy resin, outer coating of

acrylic primer;

(b) internal coating of epoxy, outer coating of zinc and

acrylic primer

Op. 14.09.2006 Dec. 08.12.2006 - TC 0617186

7304.11.00 LINE PIPE, seamless, stainless steel

Op. 04.04.2007 Dec. 22.06.2007 - TC 0704964

7304.19.00 LINE PIPE, seamless, circular cross section, complying with

American Petroleum Institute Standard Specification 5L (API 5L),

having EITHER of the following:

(a) diameter less than 33.7 mm;

(b) diameter exceeding 168.3 mm

Op. 20.07.2012 Dec. 12.11.2012 - TC 1224023

7304.19.00 LINE PIPE, carbon steel, conforming to American Society of

Testing and Materials ASTM A106 Grade B, being ANY of the

following, as listed in THE TABLE:

THE TABLE

TYPE OD WT

(a) 200NB Schedule 160 219.10 mm 23.01 mm;

(b) 250NB Schedule 80 273.10 mm 15.09 mm;

(c) 200NB Schedule 40 219.10 mm 8.18 mm;

(d) 80NB Schedule 80 88.90 mm 7.62 mm;

(e) 20NB Schedule 160 26.7 mm 5.56 mm

For the purposes of this order, all measurements have a tolerance

of + OR - 5%

Op. 05.01.2011 Dec. 04.04.2011 - TC 1100573

7304.19.00 LINE PIPE, seamless, circular cross section, having EITHER of

the following:

(a) outside diameter (OD) NOT greater than 168.3 mm;

(b) wall thickness (WT) NOT less than 16 mm,

and complying with EITHER of the following:

(a) American Society of Testing and Materials

Standards A106/A106M - 08, grade B (ASTM A106/A106M - 08,

grade B);

(b) American Petroleum Institute Standard API

specification 5L, grade X42 (API specification 5L,

grade X42)

Op. 13.08.2010 Dec. 08.11.2010 - TC 1037312

7304.19.00 LINE PIPE, seamless, to Specification ASTM A333 Grade 6,


(a) OD exceeding 209.0 mm;

(b) a WT of 12.5 mm or greater

Op. 01.01.2007 Dec. 08.11.2006 - TC 0614208

7304.19.00 TUBES OR HOLLOW BARS (NOT BEING HONED TUBES), in straight lengths,

ends plain, bevelled or threaded in accordance with ANY of the

following tube, hollow bar or pipe material Specification options:

Tariff Description

===========================================================================


(a) AS;

(b) ASME;

(c) ASTM;

(d) BS;

(e) DIN,

but without further rework, having a length NOT less than four

times the OD, as listed in THE TABLE:

THE TABLE

Outside Dia Wall Thickness

(a) NOT exceeding 219.08 mm 13.00 mm or greater but

NOT exceeding 25.00 mm;

(b) 219.08 mm or greater but 12.70 mm or greater but

NOT exceeding 254.00 mm NOT exceeding 50.80 mm;

(c) 254.00 mm or greater but 19.05 mm or greater but


(d) 323.85 mm or greater but 25.40 mm or greater but

NOT exceeding 720.73 mm NOT exceeding 75.00 mm

Op. 01.01.2007 Dec. 08.11.2006 - TC 0614209

7304.19.00 PIPES, STEEL, having a diameter NOT less than 65 cm

Op. 24.01.2007 Dec. 13.04.2007 - TC 0701302

7304.19.00 LINE PIPE, seamless, to DNV-OS-F101

Op. 01.01.2007 Dec. 06.03.2007 - TC 0703467

7304.23.00 DRILL PIPE, carbon alloy steel, having BOTH of the following:

(a) tool joints attached at each end;

(b) outside diameter NOT less than 139 mm

Op. 26.09.2014 Dec. 15.12.2014 - TC 1434260

7304.23.00 DRILL RODS, rotary drilling, having ALL of the following;

(a) friction welded male AND/OR female fittings;

(b) tensile and yield strengths exceeding 200 Newtons per

square millimetre;

(c) non-uniform internal bore;

(d) not exceeding 167 millimetres in diameter

Op. 05.08.2011 Dec. 19.12.2011 - TC 1126550

7304.23.00 DRILL PIPE, seamless, non-alloy carbon steel, circular cross

section, having EITHER of the following:

(a) outside diameter (OD) NOT greater than 168.3 mm;

(b) wall thickness (WT) NOT less than 16 mm

Op. 16.08.2010 Dec. 08.11.2010 - TC 1038045

7304.23.00 DRILL PIPES, WELLBORE, seamless, having BOTH of the following:

(a) outside diameter (OD) NOT greater than 216 mm;

(b) tool joint one end

Op. 25.11.2009 Dec. 05.02.2010 - TC 0944896

7304.23.00 DRILL PIPES, having rotary connections attached, conforming to

API Specification 7, being EITHER of the following:

(a) conforming to API Specification 5D;

(b) as listed in THE TABLE

THE TABLE

Outside Diameter Wall Thickness

(i) 88 mm to 110 mm (both inclusive) 18 mm or greater;

(ii) 110 mm to 120 mm (both inclusive) 20 mm or greater;

(iii) 120 mm to 130 mm (both inclusive) 23 mm or greater

Op. 01.01.2007 Dec. 09.11.2006 - TC 0614213

7304.23.00 DRILL RODS, FRICTION WELDED, having DIN 17MnV6 steel tool joints

Op. 01.01.2007 Dec. 27.03.2007 - TC 0703471

Tariff Description

===========================================================================


7304.23.00 DRILL PIPE, conforming to American Petroleum Institute

Specification 5D:2001 (API 5D:2001), having rotary connection

attached

Op. 11.11.2008 Dec. 06.02.2009 - TC 0839269

7304.24.00 CASING AND/OR TUBING, STAINLESS STEEL, seamless

Op. 10.04.2008 Dec. 04.07.2008 - TC 0803235

7304.29 CASING OR TUBING, oilwell (including casing or tubing with

couplings), conforming to EITHER of the following:

(a) API Specification 5CT;

(b) Manufacturers" Material Specification CR9, CR13, CR22 or

CR25 with other requirements to API Specifications 5CT,

but NOT including EITHER of the following:

(a) plain end casing or tubing;

(b) casing with connectors

Op. 01.07.1996 Dec. 06.06.1996 - TC 9605808

7304.29 JOINTS, blast, being tubing threaded at both ends, in nominal

lengths of 3.05 m or 6.10 m

Op. 01.07.1996 Dec. 16.05.1996 - TC 9608624

7304.29.00 CASING, OIL AND/OR GAS WELL, seamless, complying with American

Petroleum Institute Standard 5L (API 5L), with OR without

connectors, having an outside diameter NOT less than 300 mm and

NOT greater than 380 mm

Op. 05.08.2014 Dec. 24.11.2014 - TC 1427032

7304.29.00 CASING OR TUBING, OIL AND/OR GAS WELL, seamless, conforming to

American Petroleum Institute Specification 5CT (API 5CT), with

OR without connectors

Op. 15.04.2013 Dec. 15.07.2013 - TC 1312751

7304.29.00 CASING OR TUBING, OIL OR GAS WELL, seamless, plain end, diameter NOT

exceeding 140 mm

Op. 30.08.1999 Dec. 08.11.1999 - TC 9906606

7304.31 TUBE, seamless, cold drawn, having an outside diameter NOT exceeding

8 mm, an inside diameter NOT exceeding 4 mm, pressure rating NOT

less than 54 900 kPa, to Specification DIN 2413

Op. 08.05.1989 Dec. 26.07.1990 - TC 8903168

7304.31 TUBES, heat exchange and condenser, seamless, cold drawn, carbon

steel, in straight lengths, ends plain, bevelled or threaded BUT

without further rework, to specification ASTM A179/A 179M-88a

Op. 10.02.1992 Dec. 16.07.1992 - TC 9201981

7304.31 TUBES, seamless, cold drawn, in straight lengths, ends plain,

bevelled or threaded, BUT without further rework, to specification

DIN standard 2391: Part 2

Op. 10.02.1992 Dec. 16.07.1992 - TC 9202044

7304.31 TUBES, carbon steel, in straight lengths, ends plain, bevelled or

threaded, BUT without further rework, conforming to ASTM A179, cold

drawn, seamless, having an OD NOT less than 6.4 mm and NOT greater

than 203.2 mm

Op. 05.03.1992 Dec. 20.07.1992 - TC 9203132

7304.31 TUBES, cold drawn, seamless, to ANY of the following steel grades:

(a) K1006;

(b) K1016;

(c) K1010;

(d) K1020;

(e) K1026,

Tariff Description

===========================================================================


or ANY of the following tube specifications:

(a) JIS G3445 STKM 11-20;

(b) BS6323:Part 6:1982;

(c) ASTM A513,

and having BOTH of the following:

(a) carbon content NOT less than 0.06% and NOT greater than 0.4%

by weight;

(b) OD NOT less than 6.4 mm and NOT greater than 203.2 mm

Op. 27.07.1992 Dec. 08.10.1992 - TC 9206994

7304.31.00 WELD TEST RINGS, complying with DNV-OS-F101

Op. 08.12.2005 Dec. 03.03.2006 - TC 0516769

7304.31.00 TUBES OR HOLLOW BARS, seamless, cold drawn in straight lengths

Op. 26.11.1992 Dec. 08.03.1993 - TC 9210246

7304.39 TUBES (NOT being honed tubes), seamless, having BOTH of the

following:

(a) elevated temperature properties conforming to

Specification BS 3602 (1978) Grade 360 or AS 1835 TS 5;

(b) OD NOT less than 1 250 mm OR a WT NOT exceeding 25 mm

Op. 21.03.1985 Dec. 21.03.1985 - TC 8530426

7304.39 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths,


following tube, hollow bar or Pipe Material Specification options:

(a) AS;

(b) ASME;

(c) ASTM;

(d) BS;

(e) DIN,


times the OD, as listed in THE TABLE

THE TABLE

Outside Diameter Wall Thickness









Op. 01.01.1988 Dec. 01.01.1988 - TC 8735571

7304.39 TUBES, seamless, hot finished, boiler and superheater, in straight

lengths, ends plain, bevelled or threaded, BUT without further

rework, to specification ASTM A210/A 210M-88a

Op. 10.02.1992 Dec. 16.07.1992 - TC 9201980

7304.39 PIPE, seamless, hot finished, in straight lengths, ends plain,

bevelled or threaded BUT without further rework, to specification

ASTM A333/A333M-88a

Op. 10.02.1992 Dec. 16.07.1992 - TC 9202042

7304.39.00 PROCESS PIPES, seamless, carbon steel, circular cross-section,

having BOTH of the following:

(a) square cut plain ends OR bevelled ends;

(b) compliance with American Society for Testing and Materials

standard ASTM A333/A333M - 10

Op. 21.08.2013 Dec. 11.11.2013 - TC 1328486

Tariff Description

===========================================================================



Op. 08.12.2005 Dec. 03.03.2006 - TC 0516768

7304.39.00 HOLLOW BARS, seamless, hot rolled or hot finished in straight

lengths

Op. 22.10.1996 Dec. 06.01.1997 - TC 9611660

7304.39.00 TUBES, seamless, carbon steel, hot finished, in straight lengths,

ends plain OR bevelled OR threaded, but without further rework, to

specification DIN 1629

Op. 30.12.1996 Dec. 25.03.1997 - TC 9613286

7304.41 TUBES, stainless steel, containing 12% or more chromium, OD NOT

exceeding 3.175 mm

Op. 28.02.1984 Dec. 28.02.1984 - TC 8341367




(a) AS;

(b) ASME;

(c) ASTM;

(d) BS;

(e) DIN,



THE TABLE










Op. 01.01.1988 Dec. 01.01.1988 - TC 8735572

7304.41 TUBES, alloy steel, in straight lengths, ends plain, bevelled

or threaded in accordance with ANY of the following Pipe

Material Specification options:

(a) AS;

(b) ASME;

(c) ASTM;

(d) BS;

(e) DIN,

but without further rework, containing NOT less than 12% by

weight of chromium, having EITHER of the following:

(a) OD NOT exceeding 105 mm and WT NOT less than 4.5 mm

but NOT exceeding 25 mm;

(b) OD NOT less than 105 mm and WT NOT exceeding 25 mm

Op. 01.01.1988 Dec. 01.01.1988 - TC 8801453


Op. 08.12.2005 Dec. 03.03.2006 - TC 0516767

7304.41.00 TUBES, cold reduced, stainless steel, carbon content NOT exceeding

0.03%, to specifications ASTM A790, A789

Op. 16.07.1993 Dec. 01.11.1993 - TC 9306991

7304.41.00 TUBING, seamless stainless steel, duplex alloy S.A.F.2205 to ASTM

A 789 UNS S31803, having an outside diameter less than 25mm

Op. 05.04.1993 Dec. 05.04.1993 - TC 9329022

Tariff Description

===========================================================================


7304.41.00 TUBES, seamless, circular cross section, stainless steel, to

specification ASTM A269 or ASTM A213, cold drawn and annealed,

whether or NOT surface finished, having BOTH of the following:

(a) OD NOT exceeding 6.35 mm;

(b) WT NOT exceeding 1.20 mm

Op. 31.07.1995 Dec. 27.10.1995 - TC 9509324

7304.41.00 TUBES OR PIPES, stainless steel, seamless

Op. 25.11.2003 Dec. 08.03.2004 - TC 0314979

7304.49 TUBES, stainless steel, containing 12% or more chromium, OD NOT

exceeding 3.175 mm

Op. 01.01.1988 Dec. 01.01.1988 - TC 8635310




(a) AS;

(b) ASME;

(c) ASTM;

(d) BS;

(e) DIN,



(a) OD NOT exceeding 105 mm and WT 4.5 mm or greater but



Op. 03.07.1987 Dec. 04.09.1987 - TC 8734525




(a) AS;

(b) ASME;

(c) ASTM;

(d) BS;

(e) DIN,



THE TABLE










Op. 01.01.1988 Dec. 01.01.1988 - TC 8735573

7304.49.00 TUBING OR PIPING, seamless stainless steel, having extruded

aluminium finning

Op. 20.07.2009 Dec. 02.10.2009 - TC 0925796


Op. 08.12.2005 Dec. 03.03.2006 - TC 0516766

7304.49.00 PIPES, stainless steel, seamless, bevelled OR plain ends

Op. 29.07.1999 Dec. 15.10.1999 - TC 9905670

7304.49.00 TUBES OR PIPES, stainless steel, seamless

Op. 25.11.2003 Dec. 08.03.2004 - TC 0314980

Tariff Description

===========================================================================


7304.51 TUBES, longitudinally finned, extruded

Op. 28.02.1984 Dec. 28.02.1984 - TC 8341428

7304.51 PIPE, seamless, cold drawn, in straight lengths, ends plain,

bevelled or threaded BUT without further rework, to specification

ASTM A333/A 333M-88a

Op. 10.02.1992 Dec. 16.07.1992 - TC 9202040

7304.51 PIPE, seamless, ferritic alloy steel, cold drawn, in straight

lengths, ends plain, bevelled or threaded BUT without further


Op. 10.02.1992 Dec. 16.07.1992 - TC 9202045

7304.51.00 TUBES, threaded, seamless, cold-drawn, having ALL of the

following;

(a) outside diameter NOT greater than 39 mm;

(b) inside diameter NOT greater than 27.6 mm;

(c) length NOT greater than 2.6 m

Op. 19.05.2009 Dec. 14.08.2009 - TC 0916934


Op. 08.12.2005 Dec. 03.03.2006 - TC 0516770

7304.51.00 TUBES, seamless alloy steel, cold drawn, compliant with American

Society for Testing and Materials Standard A519/4130 (ASTM

A519/4130)

Op. 29.02.2008 Dec. 16.05.2008 - TC 0803409

7304.51.00 TUBES OR HOLLOW BARS, seamless, alloy steel, cold rolled or cold

finished, in straight lengths

Op. 17.06.1993 Dec. 24.09.1993 - TC 9304563

7304.59 TUBES OR PIPES, seamless, tested and certified to EITHER of the

following Specifications:

(a) ASTM A200 Grade T5;

(b) ASTM A335 Grade P5

Op. 01.01.1988 Dec. 01.01.1988 - TC 8801707

7304.59 TUBES, alloy steel, in straight lengths, ends plain, without

further rework, to ANY of the following Material Specifications:

(a) ASTM A213;

(b) ASME A213;

(c) BS 3059;

(d) AS 1835,

having ALL of the following:

(a) chromium content, by weight, of 0.7% or greater but NOT

exceeding 12.5%;

(b) an OD of 30 mm or greater but NOT exceeding 127 mm;

(c) WT NOT exceeding 12.5 mm

Op. 16.10.1989 Dec. 02.01.1990 - TC 8907466

7304.59 PIPE, seamless ferritic alloy steel, hot finished, in straight

lengths, ends plain, bevelled or threaded BUT without further


Op. 10.02.1992 Dec. 16.07.1992 - TC 9201999

7304.59 PIPE, seamless, hot finished, in straight lengths, ends plain,

bevelled or threaded BUT without further rework to specification

ASTM A333/A 333M-88a

Op. 10.02.1992 Dec. 16.07.1992 - TC 9202039

7304.59.00 PROCESS PIPES, seamless, carbon steel, circular cross-section,


Tariff Description

===========================================================================


(a) square cut plain ends OR bevelled ends;

(b) compliance with American Society for Testing and Materials

standard ASTM A 106/A 106M - 06a OR ASTM A106/A106M - 08

Op. 21.08.2013 Dec. 19.11.2013 - TC 1328488

7304.59.00 TUBES, seamless, alloy steel, forged, in straight lengths,


(a) length NOT greater than 1 950 mm;

(b) outside diameter (OD) NOT greater than 550 mm;

(c) wall thickness (WT) NOT less than 70 mm

Op. 17.11.2009 Dec. 22.01.2010 - TC 0943497


Op. 08.12.2005 Dec. 03.03.2006 - TC 0516771

7304.59.00 RODS, RAISE DRILL, alloy steel, integral

Op. 28.04.2008 Dec. 18.07.2008 - TC 0805489

7304.59.00 TUBES, seamless, carbon steel, hot finished in straight lengths,

ends plain, bevelled or threaded, but without further rework, to

specification AISI 4140 quenched and tempered

Op. 09.12.1992 Dec. 30.08.1993 - TC 9310300

7304.59.00 BARS, hollow, to specification AISI 4145H modified

Op. 18.04.1994 Dec. 22.07.1994 - TC 9404209

7304.59.00 TUBES OR PIPES, seamless, conforming to EITHER of the following

specifications:

(a) SA-213 T22;

(b) SA-335 P22

Op. 01.11.1996 Dec. 31.01.1997 - TC 9611933

7304.59.00 DRILL STRING SECTIONS, THREADED, ROTARY PERCUSSIVE ROCK DRILLING,


(a) hollow drill tube;

(b) hollow bar and rod external cross section dimension exceeding

52 mm, and a maximum internal dimension greater than one half

of the maximum external cross section dimension

Op. 16.05.1997 Dec. 01.08.1997 - TC 9704455

7304.59.00 TUBES OR PIPES, seamless alloy steel, hot finished, to ASTM A519

Grade 4140

Op. 08.01.1998 Dec. 13.03.1998 - TC 9800163

7304.59.00 DRILL RODS, ROTARY PERCUSSIVE ROCK DRILLING, hollow, threaded OR

tapered, external cross-section dimension exceeding 52 mm

Op. 10.08.1998 Dec. 16.10.1998 - TC 9807063

7304.59.00 TUBES, hot rolled, seamless alloy steel to specification DIN1629

Op. 19.11.1999 Dec. 31.01.2000 - TC 9908842

7304.59.00 LANCES, OXYGEN OR INERT GAS, ceramic coated

Op. 08.12.2000 Dec. 02.03.2001 - TC 0010030

7304.59.00 TUBES OR HOLLOW BARS, seamless, alloy steel, hot finished OR hot

rolled, in straight lengths

Op. 09.11.2004 Dec. 21.01.2005 - TC 0411761

7305.11.00 LINE PIPE, OIL AND GAS, complying with American

Petroleum Institute (API) Standard, Specification 5L, Grade B,

Production Specification Level (PSL) 1, having ALL of the

following:

(a) varnish coatings;

(b) length NOT less than 12 metres;

Tariff Description

===========================================================================


(c) bevelled ends;

(d) wall thickness NOT less than 9 mm and NOT greater than 13

mm;

(e) outside diameter NOT less than 640 mm and NOT greater than

800 mm;

(f) longitudinally submerged arc welding;

but NOT including spirally submerged arc welded steel line pipe

complying with Australian Standard AS 1579

Op. 10.04.2007 Dec. 12.09.2007 - TC 0705206

7305.11.00 PIPE, SUBMERGED ARC WELDED (SAW), having EITHER of the following:

(a) outside diameter NOT less than 750 mm;

(b) wall thickness NOT less than 9.53 mm

Op. 27.08.2008 Dec. 09.02.2009 - TC 0828344

7305.11.00 LINE PIPE, submerged arc welded, to DNV-OS-F101

Op. 04.11.2004 Dec. 01.02.2005 - TC 0411588

7305.12.00 STEEL LINE PIPE, OIL AND/OR GAS WELL, ELECTRIC RESISTANCE

WELDED, exceeding 406.4 mm external diameter, conforming to

American Petroleum Institute Specification 5L (API 5L)

Op. 20.07.2012 Dec. 08.11.2012 - TC 1241575

7305.12.00 LINE PIPE, ELECTRIC RESISTANCE WELDED (ERW), complying with

American Petroleum Institute Standard Specification 5L (API 5L)

Op. 20.07.2012 Dec. 10.10.2012 - TC 1224027

7305.12.00 PIPE, ELECTRIC RESISTANCE WELDED, exceeding EITHER of the

following:

(a) outside diameter 508 mm;

(b) wall thickness 12.7 mm

Op. 20.02.2008 Dec. 18.03.2010 - TC 1013309

7305.12.00 LINE PIPE, OIL AND GAS PIPELINE, steel, having BOTH of the

following:

(a) diameter NOT less than 645 mm;

(b) longitudinally welded

Op. 23.04.2007 Dec. 16.07.2007 - TC 0705875

7305.12.00 LINE PIPE, OIL AND GAS, stainless steel, welded, having an

external diameter NOT less than 406.4 mm

Op. 31.07.2008 Dec. 24.10.2008 - TC 0824211


WELDED, exceeding 406.4 mm external diameter, conforming to

American Petroleum Institute Specification 5L (API 5L)

Op. 20.07.2012 Dec. 08.11.2012 - TC 1241575

7305.19.00 PIPE, SUBMERGED ARC WELDED (SAW), helical, having BOTH of the

following:


(b) wall thickness NOT less than 9.53 mm

Op. 21.12.2011 Dec. 02.04.2012 - TC 1142287

7305.20.00 CASING, OIL AND/OR GAS WELL, ELECTRIC RESISTANCE WELDED,

conforming to American Petroleum Institute Specification 5CT

(API 5CT) with OR without connectors, external diameter

exceeding 406.4 mm

Op. 20.07.2012 Dec. 08.11.2012 - TC 1241578

7305.20.00 CASING, OIL AND/OR GAS WELL, electric resistance welded,


(API 5CT), with OR without connectors

Op. 20.07.2012 Dec. 31.10.2012 - TC 1241541

Tariff Description

===========================================================================


7305.20.00 CASING, OIL AND/OR GAS WELL, having BOTH of the following:


(b) wall thickness NOT less than 14 mm

Op. 26.03.2012 Dec. 18.06.2012 - TC 1209900

7305.20.00 CONDUCTOR CASING, OILWELL, to API specification 5L, with OR

without connectors, having BOTH of the following:

(a) outside diameter exceeding 500 mm;

(b) wall thickness exceeding 20 mm

Op. 30.07.1998 Dec. 23.10.1998 - TC 9806755




(a) AS;

(b) ASME;

(c) ASTM;

(d) BS;

(e) DIN,



(a) OD NOT less than 1 250 mm;

(b) WT 5 mm or greater but NOT exceeding 25 mm

Op. 03.07.1987 Dec. 04.09.1987 - TC 8734523

7305.31.00 PIPE MODULES, steel frame, being pipework fitted rigid

framework, having BOTH the following:

(a) length NOT less than 2.5 metres;

(b) weight NOT less than 3 tonnes

Op. 31.08.2015 Dec. 09.12.2015 - TC 1533597

7305.31.00 PIPES, electric resistance welded, circular cross-section, non-

alloy steel, complying with Australian and New Zealand Standard

1163:2009 (AS/NZS 1163:2009), Grade C450L0, having ALL of

the following:

(a) length NOT less than 9 m and NOT greater than 18.15 m;

(b) outside diameter 457 mm;

(c) wall thickness NOT less than 5.2 mm and NOT greater than

11 mm;

(d) bevelled ends;

(e) non-alloy steel complying with Japanese Industrial

Standard G 3474:2008 (JIS G 3474:2008), Grade STKT590

For the purposes of this Order, tolerances allowable for

specification (b) are +/- 5%.

Op. 07.01.2014 Dec. 07.04.2014 - TC 1400827

7305.31.00 PIPES, mild steel OR stainless steel, with OR without couplings,


(a) internal ceramic tile lining;

(b) outside diameter greater than 406.4 mm

Op. 21.03.2011 Dec. 15.06.2011 - TC 1109648

7305.31.00 TUBES, stainless steel, straight seam welded, conforming to

American Society of Testing and Materials Standards

A-312/A 312M - 09 (ASTM A-312/A 312M - 09) and

A358/A 358M - 08a (ASTM A358/A 358M - 08a), having ALL of the

following:

(a) straight lengths;

(b) ends plain or bevelled or threaded or grooved;

(c) wall thickness (WT) NOT less than 4 mm;

(d) containing NOT less than 10% by weight of chromium

Op. 01.07.2010 Dec. 29.09.2010 - TC 1029727

Tariff Description

===========================================================================


7305.31.00 WELD TEST RINGS, complying with Offshore Standard for Submarine

Pipeline Systems DNV-OS-F101

Op. 08.12.2005 Dec. 08.03.2006 - TC 0604839


Op. 08.12.2005 Dec. 03.03.2006 - TC 0516772

7306.19.00 TIE-IN SPOOLS, SUBSEA, having longitudinally welded line

pipe, complying with Det Norske Veritas Offshore Standard F101

(DNV-OS-F101), with OR without ANY of the following:

(a) anodes;

(b) coating AND/OR cladding AND/OR lining;

(c) bends;

(d) crosses;

(e) flanges;

(f) elbows;

(g) tees;

(h) reducers;

(i) protective casings

Op. 12.10.2015 Dec. 13.01.2016 - TC 1537985

7306.19.00 RISERS, OIL AND/OR GAS, rigid, complying with Det Norske Veritas

Offshore Standard F101 (DNV-OS-F101), whether OR not clad AND/OR

coated, with OR without ANY of the following:

(a) centralisers;

(b) fittings;

(c) seals

Op. 01.10.2015 Dec. 06.01.2016 - TC 1536922

7306.19.00 LINE PIPE, High Frequency Welded (HFW), duel layer fusion bonded

epoxy coated, complying with American Petroleum Institute

Standard Specification 5L (API 5L), having ALL of the following:

(a) steel AND pipe grade X65M;

(b) product specification PSL2;

(c) diameter being EITHER of the following:

(i) NOT exceeding 55 mm;

(ii) exceeding 168.3 mm

Op. 22.05.2015 Dec. 10.08.2015 - TC 1519289


American Petroleum Institute Standard Specification 5L (API 5L)

and International Standard 3183,(ISO 3183), having a diameter

exceeding 168.3 mm

Op. 18.12.2012 Dec. 18.03.2013 - TC 1248298


WELDED, conforming to American Petroleum Institute Specification

5L (API 5L) having EITHER of the following:

(a)external diameter NOT greater than 33.7 mm;

(b)external diameter NOT less than 168.3 mm and NOT greater than

406.4 mm.

Op. 15.11.2012 Dec. 17.12.2012 - TC 1248095


American Petroleum Institute Standard Specification 5L (API 5L),


(a) diameter less than 33.7 mm;

(b) diameter exceeding 168.3 mm

Op. 20.07.2012 Dec. 12.11.2012 - TC 1224029

7306.19.00 PIPE, ELECTRIC RESISTANCE WELDED, exceeding a wall thickness of

12.7 mm

Tariff Description

===========================================================================


Op. 22.02.2008 Dec. 20.11.2009 - TC 0943624

7306.19.00 PIPE, to specification API 5L Grade B, ASTM 53B, being ANY of the

following sizes (+/- 10%):

(a) OD 114.3 mm, WT 6.0 mm;

(b) OD 88.9 mm, WT 5.5 mm;

(c) OD 60.3 mm, WT 3.9 mm

Op. 01.01.2007 Dec. 09.11.2006 - TC 0614217

7306.19.00 LINE PIPE, complying with DNV-OS-F101

Op. 01.01.2007 Dec. 02.01.2007 - TC 0614760

7306.19.00 PIPES, WELDED, complying with American Petroleum Institute

Standard Specification of Line Pipe 5L, comprising ALL of the

following:

(a) outside diameter NOT less than 63 mm and NOT greater than

115 mm;

(b) wall thickness NOT less than 4 mm and NOT greater than 11

mm;

(c) yield strength capacity NOT less than 385 MPa

Op. 26.02.2007 Dec. 18.05.2007 - TC 0703024

7306.19.00 TUBES OR PIPES, ERW, bevelled ends, certified to ALL the following

specifications:

(a) AS 1163;

(b) API 5L grades B and X42;

(c) ASTM A53 grade B;

in ANY of the following sizes:

Cross Section Diameter Wall Thickness Length

NOT less than 88.5 mm and NOT less than 4 mm and NOT less than

NOT greater than 90 mm NOT greater than 10 mm 6 m

NOT less than 114 mm and NOT less than 4 mm and NOT less than


NOT less than 141 mm and NOT less than 4 mm and NOT less than


Op. 06.11.2003 Dec. 23.10.2008 - TC 0835803

7306.29.00 CASING, OIL AND/OR GAS WELL, electric resistance welded,


(API 5CT), with OR without connectors

Op. 20.07.2012 Dec. 31.10.2012 - TC 1241536

7306.29.00 TUBING, electrical resistance welded, coiled OR in spools, having

BOTH of the following:

(a) minimum continuous length of 2 000 m;

(b) minimum OD of 31 mm

Op. 01.01.2007 Dec. 09.11.2006 - TC 0614219

7306.29.00 CASING, Electric Resistance Welded (ERW), complying with

American Petroleum Institute 5CT (API 5CT) having BOTH of the

following:

(a) outside diameter of 406.4mm;

(b) wall thickness exceeding 10 mm but NOT exceeding 14 mm

For the purposes of this Order, tolerances of + or - 1% are

allowable for the specification in (a)

Op. 01.01.2007 Dec. 29.11.2006 - TC 0614773

7306.30 PIPES, lance, oxygen calorised and ceramic coated

Op. 22.08.1991 Dec. 25.05.1992 - TC 9107706

7306.30 TUBES, ERW boiler, being EITHER carbon or carbon manganese steel,

in straight lengths, ends plain, bevelled or threaded, BUT without

further rework, to specification ASTM A178/A 178M-89

Op. 10.02.1992 Dec. 16.07.1992 - TC 9201983

Tariff Description

===========================================================================


7306.30 TUBES, cold drawn, welded, to specification ASTM A513,


(a) OD NOT less than 203.2mm and NOT greater than 306.0mm;

(b) carbon content NOT less than 0.06% and NOT greater than

0.4% by weight

Op. 04.09.1992 Dec. 31.12.1992 - TC 9208087

7306.40.00 TUBES OR PIPES, welded, stainless steel in accordance with

EN10217-7TC1 OR EN 10296-2, having an outer diameter exceeding

18.0 mm and NOT exceeding 1 012.0 mm

Op. 26.10.2015 Dec. 18.01.2016 - TC 1539887

7306.30.00 TUBES, cold drawn, stress relieved, cylindrical, electric

resistance welded drawn over mandrel, non-alloy grade E355+SR,

standard EN 10305-2, having BOTH of the following:

(a) straightness of 1 mm/1000 mm of the length;

(b) internal diameter NOT less than 25.4 mm and NOT greater

than 228.6 mm

with OR without fitted end caps

Op. 20.10.2015 Dec. 13.01.2016 - TC 1539396

7306.30.00 TUBES, cold drawn, cylindrical, electric resistance welded drawn

over mandrel, non-alloy steel grade E355+C,

standard EN 10305-2, having BOTH of the following:

(a) straightness of 1 mm/1000 mm of the length;

(b) internal diameter NOT less than 25.4 mm and NOT greater

than 110.0 mm

with OR without fitted end caps

Op. 20.10.2015 Dec. 13.01.2016 - TC 1539395

7306.30.00 PIPE MODULES, rigid steel frame, having flanged pipework, pipe

diameter NOT greater than 450 mm

Op. 01.10.2015 Dec. 14.12.2015 - TC 1536918

7306.30.00 COILED TUBING, OIL AND GAS WELL, whether OR not on spools AND/OR

reels

Op. 20.12.2013 Dec. 20.03.2014 - TC 1409618

7306.30.00 PIPES, mild steel, with OR without couplings, having BOTH of the

following:


(b) outside diameter less than 406.4 mm

Op. 28.02.2011 Dec. 06.06.2011 - TC 1107493

7306.30.00 PIPES, welded steel, multilayer, having ALL of the following:

(a) steel inner service pipe;

(b) polyurethane foam insulation incorporating copper wires;

(c) high density polyethylene outer casing

Op. 07.06.2010 Dec. 30.08.2010 - TC 1025391

7306.30.00 TUBES, welded, complying with Japanese Industrial Standard G3445

STK11A (JIS G3445 STKM11A), having an outside diameter NOT

greater than 12 mm

Op. 07.02.2007 Dec. 20.04.2007 - TC 0701959

7306.30.00 TUBES OR PIPES, ERW, conforming to specification SA 178

Op. 01.11.1996 Dec. 20.01.1997 - TC 9611935

7306.30.00 TUBES, cold drawn, welded, stress relieved, to DIN specification

2393, having ALL of the following:

(a) outside diameter of 15 mm to 22 mm;

(b) inside diameter of 13 mm to 19 mm;

(c) wall thickness of 1 mm to 1.6 mm

Tariff Description

===========================================================================


Op. 16.04.2002 Dec. 05.07.2002 - TC 0203211

7306.30.00 TUBES, WELDED, non alloy steel, being EITHER of the following:

(a) single wall resistance welded to specification SAE J526,


(i) carbon content NOT greater than 0.13%;

(ii) outside diameter NOT greater than 11.50 mm;

(iii) wall thickness NOT less than 0.5 mm and NOT greater

than 1.0 mm;

(b) double wall copper brazed to specification SAE J527,


(i) carbon content NOT greater than 0.13%;

(ii) outside diameter NOT greater than 13 mm;

(iii) wall thickness NOT less than 0.5 mm and NOT greater

than 1.0 mm

Op. 31.03.2003 Dec. 27.06.2003 - TC 0303383

7306.40 TUBES, stainless steel, longitudinally welded, having BOTH of the

following dimensions:

(a) an OD 105 mm or greater but NOT exceeding 220 mm;

(b) a WT 1.50 mm or greater but NOT exceeding 5.00 mm

Op. 30.04.1985 Dec. 05.09.1985 - TC 8531977




(a) AS;

(b) ASME;

(c) ASTM;

(d) BS;

(e) DIN,



(a) OD NOT exceeding 105 mm and WT 4.5 mm or greater but NOT

exceeding 25.0 mm;


Op. 01.01.1988 Dec. 01.01.1988 - TC 8733276

7306.40.00 PIPE MODULES, rigid steel frame, having flanged pipework, pipe

diameter NOT greater than 450 mm

Op. 01.10.2015 Dec. 14.12.2015 - TC 1536919

7306.40.00 TUBES, stainless steel, spiral welded, having ALL of the

following:

(a) outside diameter NOT less than 105 mm and NOT greater

than 220 mm;

(b) wall thickness NOT less than 1.50 mm and NOT greater than

7.00 mm;

(c) SAE International grade 409 OR grade 410L

Op. 28.07.2015 Dec. 30.10.2015 - TC 1529367

7306.40.00 PIPES, stainless steel, press fit, having ALL of the following:

(a) ethylene propylene diene monomer(EPDM) rubber seal;

(b) stainless steel OR gunmetal press connector;

(c) outside diameter NOT less than 12 mm and NOT greater

than 54 mm

Op. 15.01.2015 Dec. 08.04.2015 - TC 1502400

7306.40.00 PIPES, stainless steel, press fit, having ALL of the following:

(a) ethylene propylene diene (EPDM) rubber seal;

(b) stainless steel OR gunmetal press connector;

(c) outside diameter NOT less than 12 mm and NOT greater than

108 mm

Op. 15.01.2015 Dec. 15.04.2015 - TC 1502401

Tariff Description

===========================================================================


7306.40.00 PRESSURE TUBING, stainless steel, wound on spools OR reels,


(a) wall thickness NOT greater than 1.70 mm;

(b) outer diameter NOT greater than 14.00 mm;

(c) fluorinated ethylene propylene (FEP) protective outer pipe

cover

Op. 27.08.2014 Dec. 17.11.2014 - TC 1430285

7306.40.00 HYDRAULIC CONTROL LINES, OIL AND/OR GAS WELL EQUIPMENT, wound on

spools OR reels, including BOTH of the following:

(a) NOT less than 2 stainless steel pipes, having BOTH of the

following:

(i) pipe wall thickness NOT greater than 1.36 mm;

(ii) pipe outer diameter NOT less than 5.70 mm and NOT

greater than 6.90 mm,

(b) ethylene tetrafluoroethylene (ETFE) protective cover

Op. 20.06.2014 Dec. 10.09.2014 - TC 1421009

7306.40.00 TUBES OR PIPES, stainless steel, longitudinal welded, in

straight lengths, conforming to EITHER of the following

specifications:

(a) American Society for Testing and Materials (ASTM)

specifications A249 OR A268 OR A269 OR A270 OR A554 OR

A688 OR A789;

(b) Australian Standard 1528 (AS 1528)

Op. 06.02.2014 Dec. 05.05.2014 - TC 1405087

7306.40.00 TUBES OR PIPES, stainless steel, welded, in straight

lengths, conforming to ANY of the following American

Society for Testing and Materials (ASTM) specifications:

(a) A312;

(b) A358;

(c) A409;

(d) A778;

(e) A790;

(f) A813;

(g) A814;

(h) A928;

(i) A999

Op. 23.12.2013 Dec. 17.03.2014 - TC 1342173

7306.40.00 PIPES, stainless steel, having ALL of the following:

(a) outside diameter NOT less than 10.3 mm and NOT greater

than 406.4 mm;

(b) wall thickness NOT less than 1.24 mm and NOT greater than

33.32 mm;

(c) compliance with American Society for Testing and Materials

standards Designations: ASTM A269-10 OR

ASTM A312/A312M - 11 OR ASTM A554-13

Op. 03.10.2013 Dec. 13.01.2014 - TC 1333366

7306.40.00 TUBES AND/OR PIPES, stainless steel, longitudinal welded, rolled

seam, having ALL of the following:

(a) outside diameter NOT less than 10 mm and NOT greater than

219 mm;

(b) wall thickness NOT less than 1 mm and NOT greater than

2.6 mm;

(c) conforming to American Iron and Steel Institute

specifications 304 OR 316L (AISI 304 OR AISI 316L)

Op. 08.07.2013 Dec. 02.10.2013 - TC 1323026

7306.40.00 PIPES, stainless steel, with OR without couplings, having BOTH

of the following:

Tariff Description

===========================================================================



(b) outside diameter less than 406.4 mm

Op. 21.03.2011 Dec. 15.06.2011 - TC 1109650

7306.40.00 TUBES OR PIPES, stainless steel, to specification UNS S31803, having

chemical composition by weight of ALL the following:

(a) carbon : 0.030% maximum;

(b) manganese : 2.00% maximum;

(c) phosphorus : 0.030% maximum;

(d) sulphur : 0.020% maximum;

(e) silicon : 1.00% maximum;

(f) chromium : 21.00 - 23.00% both inclusive;

(g) nickel : 4.50 - 6.50% both inclusive;

(h) nitrogen : 0.03 - 0.20% maximum;

(i) molybdenum : 2.50 - 3.50% both inclusive

Op. 06.06.1994 Dec. 09.09.1994 - TC 9405021

7306.50.00 TUBES, ERW, aluminized, type JIS G3445, having ALL of the following:

(a) 12.7 mm OD;

(b) 1.6 mm WT;

(c) 5 700 mm mill length

Op. 14.04.1994 Dec. 29.07.1994 - TC 9404172

7306.61.00 TUBES, square OR rectangular, electric resistance welded,

complying with Australian/New Zealand Standard 1163:2009 (AS/NZS

1163:2009), Grade C350L0 OR C450L0, with a perimeter NOT less

than 1 050 mm and having EITHER (a) OR (b) as follows:

(a) silicon content plus 2.5 times the phosphorus content

NOT greater than 0.09%;

(b) silicon content greater than 0.14% and NOT greater than

0.24%

Op. 16.02.2016 Dec. 16.03.2016 - TC 1609617

7306.61.00 TUBES, square OR rectangular, electric resistance welded,

complying with Australian/New Zealand Standard 1163:2009 (AS/NZS

1163:2009), Grade C350L0 OR C450L0, having EITHER (a) OR (b) AND

(c), as follows:

(a) silicon content plus 2.5 times the phosphorus content

NOT greater than 0.09%;

(b) silicon content greater than 0.14% and NOT greater than

0.24%;

(c) perimeter NOT less than 1 050 mm

Op. 16.02.2016 Dec. 16.03.2016 - TC 1609618

7306.61.00 TUBES OR PIPES, stainless steel, square OR rectangular cross

section, longitudinal welded in straight lengths, conforming to

American Society for Testing and Materials A554 (ASTM A554)

specification

Op. 06.02.2014 Dec. 05.05.2014 - TC 1405088

7306.61.00 TUBES, rectangular, stainless steel, NOT less than 100 mm x 50 mm

across the flat dimensions

Op. 01.01.2007 Dec. 09.11.2006 - TC 0614222

7306.61.00 TUBES, square, stainless steel, NOT less than 100 mm x 100 mm across

the flat dimension

Op. 01.01.2007 Dec. 09.11.2006 - TC 0614223

7306.61.00 TUBES, square or rectangular, stainless steel to grade 1.4003,


(a) width NOT greater than 105 mm;

(b) wall thickness NOT greater than 4 mm

Op. 22.10.2008 Dec. 27.02.2009 - TC 0836453

Tariff Description

===========================================================================


7306.69.00 TUBES OR PIPES, stainless steel, longitudinal welded in straight

lengths, conforming to American Society for Testing and

Materials A554 (ASTM A554) specification, being ANY of the

following cross sections:

(a) oval;

(b) slotted;

(c) triangular;

(d) D section;

(e) tear drop

Op. 06.02.2014 Dec. 05.05.2014 - TC 1405089

7306.69.00 TUBES, cold drawn, carbon steel, hollow frame profile, having

ANY of the following sectional dimensions:

Length Width Wall Thickness

(a) 90 mm 41 mm 2.0 mm;

(b) 104 mm 43 mm 2.5 mm;

(c) 104 mm 43 mm 3.0 mm

Op. 01.01.2007 Dec. 08.05.2007 - TC 0705891

7307.11.00 FITTINGS, TUBE AND PIPE, rolled grooved, galvanised OR painted,

with OR without gaskets, being ANY of the following:

(a) elbows;

(b) couplings;

(c) reducers;

(d) adaptors;

(e) tees;

(f) caps;

(g) crosses;

(h) reducing tees;

(i) grooved flanges;

(j) adaptor flanges

Op. 19.08.2014 Dec. 10.11.2014 - TC 1429119

7307.11.00 FITTINGS, TEE SHAPED, TUBE OR PIPE JOINT, iron, threaded,

galvanised OR painted, including ALL of the following:

(a) outlet housing, with OR without gaskets;

(b) bolts AND/OR U shaped bolts;

(c) nuts

Op. 19.08.2014 Dec. 10.11.2014 - TC 1429120

7307.11.00 FITTINGS, PIPE, cast iron, non-combustible, non-flammable,

complying with European Standard EN 877:1999 (EN 877:1999)

Op. 13.10.2006 Dec. 22.12.2006 - TC 0615826

7307.11.00 COUPLINGS, CLAW, cast iron

Op. 22.04.2008 Dec. 18.07.2008 - TC 0804812

7307.11.00 FITTINGS, ELBOWS AND/OR TEES, painted roll, grooved

Op. 09.09.2008 Dec. 28.11.2008 - TC 0830239

7307.19 FITTINGS, pipe, buttweld, socketweld or threaded, being EITHER of

the following:

(a) manufactured from ASTM A-216 WCB carbon steel castings;

(b) manufactured from ASTM A-148 GR 60-90 steel castings

Op. 18.02.1985 Dec. 23.07.1985 - TC 8530530

7307.19.00 COUPLINGS, CLAW, cast stainless steel, with OR without locking

pins, having ALL of the following:

(a) diameter NOT less than 10 mm and NOT greater than 50 mm;

(b) threaded male OR threaded female OR hose end connections;

(c) bellows seals

Op. 23.11.2015 Dec. 03.03.2016 - TC 1608634

7307.19.00 FITTINGS, PIPE AND/OR TUBE, malleable cast iron, reducing OR non-

Tariff Description

===========================================================================


reducing, being ANY of the following:

(a) tees;

(b) combination tees and crosses;

(c) corners;

(d) crosses;

(e) cross sets;

(f) crossovers;

(g) elbows;

(h) flanges;

(i) sockets;

(j) side palms;

(k) supports;

(l) swivels;

(m) couplings;

(n) hooks;

(o) collars;

(p) collar plates;

(q) hinges;

(r) panel clips;

(s) bases;

(t) base plates

Op. 29.09.2010 Dec. 20.12.2010 - TC 1044234

7307.19.00 FITTINGS, PIPE, ductile cast iron

Op. 10.04.2008 Dec. 20.06.2008 - TC 0803227

7307.19.00 FITTINGS, CAMLOCK, stainless steel, being ANY of the following:

(a) male sections and/or female sections;

(b) plugs;

(c) caps

Op. 22.04.2008 Dec. 18.07.2008 - TC 0804811

7307.19.00 COUPLINGS, flexible, cast, stainless steel, having internal

rubber gaskets

Op. 29.10.2008 Dec. 16.01.2009 - TC 0837499

7307.19.00 PIPE FITTINGS, roll grooved or shouldered, being ANY of the

following:

(a) elbows;

(b) tees;

(c) reducers;

(d) end caps;

(e) adapters

Op. 04.12.2008 Dec. 27.02.2009 - TC 0842803

7307.19.00 FITTINGS, pipe, malleable cast iron

Op. 28.04.1993 Dec. 30.07.1993 - TC 9305440

7307.19.00 FITTINGS, pipe, B.S.P thread, made of galvanised malleable iron, to

BS 1256, being ANY of the following:

(a) elbows, 90 degrees, being EITHER, female to female, or male to

female;

(b) elbows, 45 degrees, being female to female;

(c) elbows, 3 way;

(d) elbows, reducing, 90 degrees;

(e) tees, including 4 way, and reducing tees;

(f) bush, hexagon;

(g) caps;

(h) crosses;

(i) backnuts;

(j) nipples, being ANY of the following:

(i) hexagon;

(ii) barrel;

(iii) plain;

Tariff Description

===========================================================================


(iv) reducing;

(k) sockets including reducing sockets;

(l) plugs, square head;

(m) bends, 90 degrees, EITHER, male to female, or female to

female;

(n) bends, 45 degrees, male to female;

(o) unions, EITHER, male to female, or female to female

Op. 06.07.1993 Dec. 08.10.1993 - TC 9306802

7307.19.00 PIPE FITTINGS, POTABLE WATER AND GAS LINES, being EITHER of the

FOLLOWING:

(a) malleable cast iron couplings, incorporating a rubber seal

and washer

(b) tapped OR non tapped plugs incorporating a rubber seal

Op. 23.05.1996 Dec. 06.09.1996 - TC 9607790

7307.21.00 FLANGES, STAINLESS STEEL PIPE, including internal alumina

ceramic tiles

Op. 28.02.2011 Dec. 23.05.2011 - TC 1107490

7307.21.00 FLANGES, PIPE, stainless steel, seamless

Op. 29.07.1999 Dec. 15.10.1999 - TC 9905666

7307.22.00 FITTINGS, TUBE, stainless steel, with OR without seals, being

threaded bends

Op. 31.03.2010 Dec. 09.07.2010 - TC 1015482

7307.22.00 FITTINGS, VACUUM, stainless steel, operating pressure lower than

133 x 0.0000001 MPa, being EITHER of the following:

(a) couplings;

(b) elbows

Op. 18.12.1997 Dec. 27.02.1998 - TC 9711204

7307.23 BENDS, CROSSES, ELBOWS OR TEES, buttweld, stainless steel,

conforming dimensionally to ANY of the following Specifications:

(a) BS 1640;

(b) ANSI B16.9;

(c) ANSI B16.28

Op. 28.02.1984 Dec. 28.02.1984 - TC 8341312

7307.23 FITTINGS, stainless steel, tube or pipe, buttweld, annealed,

internally polished

Op. 23.11.1987 Dec. 23.02.1989 - TC 8735514

7307.23 FITTINGS, seamless, stainless steel grade 316L, to specification

ASTM 269 or ASTM 270, electropolished internally through entire

length

Op. 20.05.1988 Dec. 02.05.1989 - TC 8805455

7307.23.00 FITTINGS, TUBE OR PIPE, stainless steel in accordance with

EN10253-3 OR EN10253-4, being ANY of the following:

(a) elbows;

(b) tees;

(c) reducers;

(d) collars;

(e) end caps

Op. 26.10.2015 Dec. 18.01.2016 - TC 1539885

7307.23.00 FITTINGS, TEE, seamless, stainless steel, duplex

Op. 03.09.2015 Dec. 30.11.2015 - TC 1534129

7307.23.00 CONNECTOR HUBS, PIPE CLAMP, stainless steel, with OR without

seals

Op. 17.06.2014 Dec. 10.09.2014 - TC 1420343

Tariff Description

===========================================================================


7307.23.00 REDUCERS, seamless, butt weld, stainless steel

Op. 26.10.2012 Dec. 07.01.2013 - TC 1241137

7307.29 RINGS, gasket or packing, to API Specification 6A, capable of

operating at temperatures of 125 degrees C or greater

Op. 30.12.1987 Dec. 27.04.1988 - TC 8733301

7307.29.00 TUBE FITTINGS, stainless steel, press tool connection, having

ALL of the following:

(a) ethylene propylene diene monomer (EPDM) rubber seals;

(b) inside diameter NOT less than 15 mm and NOT greater than

108 mm;

(c) with OR without one flanged OR screw OR plain end

connection;

(d) being ANY of the following:

(i) couplings;

(ii) slip couplings;

(iii) reducers;

(iv) tees;

(v) union connectors;

(vi) adapters;

(vii) end caps

Op. 03.03.2015 Dec. 25.05.2015 - TC 1508749

7307.29.00 TUBE FITTINGS, stainless steel, press tool connection, having


(a) ethylene propylene diene monomer (EPDM) rubber seals;

(b) inside diameter NOT less than 15 mm and NOT greater than

108 mm;

(c) with OR without one flanged OR screw OR plain end

connection;

(d) being ANY of the following:

(i) elbows, including back plated;

(ii) bends;

(iii) sleeves

Op. 03.03.2015 Dec. 25.05.2015 - TC 1508754

7307.29.00 PUP JOINTS, OIL AND/OR GAS WELL TUBING, stainless steel,

threaded, perforated, with OR without thread protectors

Op. 06.03.2015 Dec. 25.05.2015 - TC 1509480

7307.29.00 CROSSOVER CONNECTORS, OIL AND/OR GAS WELL, subsea AND/OR

surface, stainless steel

Op. 10.03.2015 Dec. 07.06.2015 - TC 1509604

7307.29.00 PUP JOINTS, TUBING, OIL AND/OR GAS WELL, stainless steel,

threaded, seamless, with OR without thread protectors, having an

external working pressure rating of NOT less than 415 bar and

NOT greater than 450 bar

Op. 24.12.2014 Dec. 14.03.2015 - TC 1500003

7307.29.00 COUPLINGS, FLOW, OIL AND/OR GAS WELL, stainless steel, having

BOTH of the following:

(a) threaded connections;

(b) internal working pressure rating NOT less than 850 bar

Op. 23.09.2014 Dec. 15.12.2014 - TC 1433855

7307.29.00 CONNECTOR HUBS, PIPE CLAMP, stainless steel, with OR without

seals

Op. 17.06.2014 Dec. 01.09.2014 - TC 1420587

7307.29.00 STAB PLATES, SUBSEA, stainless steel, having NOT less than 8

connection points

Tariff Description

===========================================================================


Op. 25.02.2013 Dec. 02.05.2013 - TC 1306853

7307.29.00 COUPLINGS, PIPE, compression, stainless steel, having ALL of the

following:

(a) inside diameter NOT less than 200 mm;

(b) single sealing sleeve consisting of a single sealing lip

on each side with progressive sealing effect;

(c) single radial positioned locking system with 1 OR 2 OR 3

screws

Op. 26.07.2012 Dec. 22.10.2012 - TC 1227050

7307.29.00 CONNECTORS, STAB, SUBSEA, male AND/OR female, with OR without

protective caps

Op. 15.05.2012 Dec. 06.08.2012 - TC 1215919

7307.29.00 FITTINGS, DRAINAGE, Grade 316L stainless steel, being ANY of the

following:

(a) filter baskets;

(b) removable water traps;

(c) grates;

(d) drainage bowls, having a diameter NOT greater than 300 mm

Op. 24.09.2010 Dec. 20.12.2010 - TC 1043685

7307.29.00 FITTINGS, TUBE, stainless steel, with OR without seals, being


(a) couplings having a diameter NOT greater than 200 mm;

(b) reducers;

(c) bends;

(d) T junctions;

(e) union connectors;

(f) adapters

Op. 29.04.2010 Dec. 09.07.2010 - TC 1019464

7307.29.00 FITTINGS, PIPE AND TUBE, Grade 316L stainless steel, push fit,

with or without seal, being ANY of the following:

(a) pipe incorporating a socket;

(b) bends;

(c) pipe, having NOT less than 45 degree junctions and NOT

greater than 90 degree junctions;

(d) double sockets;

(e) "P" traps;

(f) bottle trap;

(g) eccentric increasers;

(h) eccentric reducers;

(i) access bends;

(j) threaded adaptor

Op. 25.02.2010 Dec. 14.05.2010 - TC 1009883

7307.29.00 FITTINGS, DRAINAGE, Grade 316L stainless steel, being ALL

of the following:

(a) filter baskets;

(b) removable water traps;

(c) grates

Op. 25.02.2010 Dec. 14.05.2010 - TC 1009880

7307.29.00 FITTINGS, PIPE AND TUBE, stainless steel, being ANY of the

following:

(a) sealing rings;

(b) bodies;

(c) cap nuts;

(d) weld cones;

(e) flare adaptors

Op. 11.03.2009 Dec. 06.11.2009 - TC 0941426

Tariff Description

===========================================================================


7307.29.00 FITTINGS, CAMLOCK, being ANY of the following:

(a) male sections and/or female sections;

(b) plugs;

(c) caps

Op. 20.12.2007 Dec. 07.03.2008 - TC 0710840

7307.29.00 FITTINGS, COUPLING, HOSE, quick connect, being ANY of the

following;

(a) male sections;

(b) female sections;

(c) lever rings;

(d) male plugs;

(e) female caps

Op. 21.12.2007 Dec. 07.03.2008 - TC 0721937

7307.29.00 COUPLINGS, HOSE, quick connect, comprising ALL of the following:

(a) male sections;


(c) lever rings

Op. 21.12.2007 Dec. 14.03.2008 - TC 0721940

7307.29.00 FITTINGS, ROOF DRAINAGE, stainless steel, being ANY of the

following:

(a) rainwater outlets;

(b) hoppers;

(c) elbows;

(d) s-curves;

(e) pipe flaps

including sets of 2 or more of the above

Op. 14.10.2008 Dec. 14.01.2009 - TC 0835301

7307.29.00 COUPLINGS, camlocking, to material 316 stainless steel, 15 mm to 200

mm, inclusive of both adaptors (male) and couplers (female).

Op. 13.08.1993 Dec. 10.02.1994 - TC 9307389

7307.29.00 JOINTS, swivel, stainless steel, v-ring type, pressure rating

greater than 6 800 KPa

Op. 14.06.1993 Dec. 23.09.1993 - TC 9314494

7307.29.00 FITTINGS, pipe, forged stainless steel to specification type F 51

ASTM UNS S 31803, having the surface descaled by turning

Op. 27.05.1994 Dec. 02.09.1994 - TC 9404892

7307.29.00 FITTINGS, vacuum, stainless steel, helium leak tested, rated to

lower than 133 x 10 -7 MPa, being ANY of the following:

(a) plug;

(b) cap;

(c) gland;

(d) body;

(e) female nut;

(f) male nut;

(g) bodies, assembled with nuts and ferrules;

(h) assemblies including ANY of the above

Op. 22.05.1997 Dec. 15.08.1997 - TC 9704622

7307.29.00 COUPLINGS, FLOW, OIL AND GAS WELL, stainless steel

Op. 15.12.1997 Dec. 27.02.1998 - TC 9711103

7307.91.00 FLANGES, STEEL PIPE, including internal alumina ceramic tiles

Op. 28.02.2011 Dec. 30.05.2011 - TC 1107491

7307.91.00 FLANGES, PIPE, being ANY of the following:

(a) weld neck flanges;

(b) blind flanges;

Tariff Description

===========================================================================


(c) spectacle blind flanges;

(d) slip on flanges;

(e) socket weld flanges;

(f) threaded flanges;

(g) bulkhead flanges

Op. 20.02.2008 Dec. 02.05.2008 - TC 0803404

7307.91.00 FLANGE ADAPTERS, PIPE OR TUBE OR HOSE, carbon steel, with or

without seal

Op. 03.12.2008 Dec. 27.02.2009 - TC 0842547

7307.91.00 FLANGES, HOT FORGED, SEAMLESS, comprising ALL of the following:

(a) inner diameter NOT less than 1 500 mm;

(b) width NOT greater than 400 mm;

(c) outer diameter NOT less than 2 000 mm

Op. 09.10.2003 Dec. 03.03.2004 - TC 0312809

7307.92.00 FITTINGS, TUBE, carbon steel, press fit, with OR without seals,

being threaded bends having an internal AND/OR external zinc

coating NOT greater than 8 micron

Op. 18.10.2010 Dec. 13.01.2011 - TC 1046727

7307.92.00 ELBOWS, threaded

Op. 08.10.2008 Dec. 14.01.2009 - TC 0834585

7307.92.00 FITTINGS AND ADAPTORS, PIPE OR TUBE OR HOSE, carbon steel, with

or without seal, being ANY of the following:

(a) elbows, 90 degrees;

(b) elbows, 45 degrees;

(c) elbows, 3 way tees, being either male to female OR

combinations of both;

(d) tube sleeves;

(e) bends, 90 degrees;

(f) bends, 45 degrees

Op. 03.12.2008 Dec. 27.02.2009 - TC 0842548

7307.92.00 FITTINGS, pipe, steel, complying with standards BS1740 or AS3672

Op. 10.05.1994 Dec. 19.08.1994 - TC 9404635

7307.92.00 FITTINGS, PIPE AND TUBE, including sealing rings, bodies, nuts and

weld cones, having BOTH of the following:

(a) compliance with pressure rating of either LL, L or S to

DIN 2353;

(b) interchangeability of the whole or any component of the

fitting with other fittings or components which comply with

the dimensional specifications set out in DIN 2353,

but NOT including ANY of the following:

(a) stainless steel fittings;

(b) twin ferrule fittings

Op. 03.11.1995 Dec. 09.02.1996 - TC 9511750

7307.92.00 FITTINGS, TUBE, elbow, carbon steel, twin ferrule

Op. 18.11.1997 Dec. 23.01.1998 - TC 9710155

7307.93 FITTINGS, buttweld, in accordance with Dimensional Specification

MSS-SP75 and Material Specification API 5LX

Op. 28.02.1984 Dec. 28.02.1984 - TC 8341295

7307.93 FITTINGS, buttweld pipe, being ANY of the following:

(a) to ASTM Specification A420 GRWPL6:

(i) elbows, 45 degrees;

(ii) elbows, 90 degrees, OD NOT exceeding 304.8 mm;

(iii) reducers, eccentric;

(b) to ASTM Specification A234 GRWP1:

Tariff Description

===========================================================================


(i) elbows, 45 degrees or 90 degrees, OD NOT exceeding

254 mm;

(ii) reducers, eccentric, OD at larger end NOT exceeding

254 mm

Op. 28.02.1984 Dec. 28.02.1984 - TC 8341297

7307.93 FITTINGS, being ANY of the following:

(a) elbows to ASTM Specification A234 WPB, having a dia less

than 406.4 mm OD;

(b) reducers to ASTM Specification A234 WPB, having BOTH

diameters less than 406.4 mm OD;

(c) elbows, reducers or tees to ASTM Specification A234 WP 11

Op. 19.10.1987 Dec. 21.12.1987 - TC 8735075

7307.93 JOINTS, insulating, monobloc or monolithic

Op. 01.01.1988 Dec. 01.01.1988 - TC 8803112

7307.93.00 CONNECTOR HUBS, PIPE CLAMP, carbon steel, with OR without seals

Op. 17.06.2014 Dec. 10.09.2014 - TC 1420583

7307.93.00 FITTINGS, PIPE AND/OR TUBE, butt weld, being caps of carbon

steel to American Society of Testing and Materials Specification

A234 Grade WPB (ASTM A234 Grade WPB)

Op. 21.10.2010 Dec. 10.01.2011 - TC 1047333

7307.93.00 FITTINGS, PIPE OR TUBE, butt-welded, forged steel, being

reinforced and contoured connections

Op. 28.07.2009 Dec. 16.10.2009 - TC 0927139

7307.93.00 FITTINGS, PIPE AND/OR TUBE, butt weld, alloy steel, being end

caps

Op. 28.07.2009 Dec. 09.10.2009 - TC 0927136

7307.93.00 FITTINGS, BUTTWELD, being ANY of the following:

(a) bends;

(b) crosses;

(c) elbows;

(d) reducers;

(e) tees

Op. 06.06.2005 Dec. 24.10.2005 - TC 0506772

7307.93.00 FITTINGS, buttweld, forged, integrally reinforced, contoured-insert

vessel or piping branch connections, bore sizes 15 mm - 1 200 mm

Op. 01.03.1993 Dec. 04.06.1993 - TC 9308562

7307.93.00 REDUCERS, buttweld, having a minimum outside diameter between 70 mm

and 200 mm (+ or - 0.001%)

Op. 11.02.1998 Dec. 11.05.1998 - TC 9801278

7307.93.00 FITTINGS, buttweld, to specifications BS1640 OR ANSI B16.9 OR

ANSI B16.28, being ANY of the following:

(a) bends, 30 degrees, 45 degrees, 50 degrees, 60 degrees,

90 degrees OR 180 degrees, having an outside diameter between

17 mm and 406.4 mm;

(b) tees, equal OR reducing, having an outside diameter of

406.4 mm OR less

For the purposes of this order, ALL measurements have a tolerance of

+ OR - 5%

Op. 11.02.1998 Dec. 12.08.1998 - TC 9806998

7307.99 ELBOWS, socketweld, being ANY of the following:

(a) 15 degrees;

(b) 45 degrees;

(c) 90 degrees ID exceeding 50.8 mm

Tariff Description

===========================================================================


Op. 06.03.1984 Dec. 06.03.1984 - TC 8341420

7307.99 JOINTS, insulating, monobloc or monolithic

Op. 28.02.1984 Dec. 28.02.1984 - TC 8341449

7307.99 COUPLINGS, hose, having a working capacity of 206 MPa or greater

Op. 30.10.1984 Dec. 30.10.1984 - TC 8434699

7307.99 COUPLINGS, pipe or hose, quick connect (or disconnect), comprising

male and female ring lock couplings, hinged ring band snap lock

and double lip gasket, to suit pipes and hoses having an OD of

50 mm or greater

Op. 14.12.1984 Dec. 30.04.1985 - TC 8530126

7307.99 RINGS, gasket or packing, to API Specification 6A, capable of

operating at temperatures of 125 degrees C or greater

Op. 01.01.1988 Dec. 27.04.1988 - TC 8802330

7307.99 FITTINGS, pipe, fluoro-polymer lined

Op. 12.02.1988 Dec. 21.12.1988 - TC 8802801

7307.99 FITTINGS, steel pipe, being EITHER of the following:

(a) three lug wing nut unions, dia NOT exceeding 300 mm,

minimum operating pressure 6.80 MPa;

(b) hub clamp assemblies, consisting of ALL of the following:

(i) clamp segments;

(ii) hubs;

(iii) seal ring

Op. 23.02.1988 Dec. 16.09.1988 - TC 8802877

7307.99 COUPLINGS, casing or tubing, seamless to Specification API-5CT,

section 8

Op. 05.12.1988 Dec. 07.06.1989 - TC 8902264

7307.99 JOINTS, swivel, pressure rating over 40 MPa

Op. 23.04.1991 Dec. 02.09.1991 - TC 9104099

7307.99 CLAMPS, pipe repair (but NOT including clamps incorporating

stainless steel flexible bands), having ALL of the following

characteristics:

(a) seal by ANY of the following methods:

(i) clamping or thrust screws;

(ii) girder rings;

(iii) packing or force screws;

(b) carbon steel construction;

(c) of fixed dia;

(d) capable of withstanding a working pressure of 6 900 kPa

or greater

Op. 01.01.1988 Dec. 11.09.1992 - TC 9206167

7307.99 CLOSURES, pressurised pipeline, hinged, quick release, diameter

150 mm or greater, but NOT including screw top type closures

Op. 13.07.1992 Dec. 08.10.1992 - TC 9206615

7307.99.00 FLOWLINE END TERMINATIONS, SUBSEA, with OR without ANY of the

following:

(a) anodes;

(b) mud mats;

(c) protective frames;

(d) support bases

Op. 15.10.2015 Dec. 05.01.2016 - TC 1538598

7307.99.00 PIPE FITTINGS, being 45 AND/OR 90 degree threaded AND/OR

butt weld carbon steel hammer lug union end connection elbows,

Tariff Description

===========================================================================


having a design pressure rating NOT less than 2 300 psi

Op. 16.09.2015 Dec. 14.12.2015 - TC 1535358

7307.99.00 HAMMER UNIONS, lugged wing nut type, with OR without seals,

including ANY of the following:

(a) male AND/OR female sub sections;

(b) plugs;

(c) caps;

(d) wing nuts AND/OR split nuts

Op. 16.06.2015 Dec. 08.09.2015 - TC 1521815

7307.99.00 CONNECTOR HUBS, PIPE CLAMP, carbon steel, with OR without seals

Op. 17.06.2014 Dec. 10.09.2014 - TC 1420344

7307.99.00 END CAPS, PRESSURE VESSEL

Op. 01.08.2013 Dec. 21.10.2013 - TC 1325951

7307.99.00 CONNECTORS OR COUPLINGS, CASING OR TUBING, OIL AND/OR GAS WELL,


(API 5CT)

Op. 15.04.2013 Dec. 15.07.2013 - TC 1312752

7307.99.00 CROSSOVER CONNECTORS, OIL AND/OR GAS WELL EQUIPMENT, SUBSEA

AND/OR SURFACE

Op. 25.01.2013 Dec. 08.04.2013 - TC 1303345

7307.99.00 COUPLINGS, CROSSOVER, OIL AND/OR GAS WELL EQUIPMENT, SUBSEA

AND/OR SURFACE

Op. 15.01.2013 Dec. 03.04.2013 - TC 1301796

7307.99.00 COUPLINGS, PIPE, compression, hot dipped galvanised, having ALL

of the following:

(a) inside diameter NOT less than 30 mm;

(b) single sealing sleeve consisting of a single sealing lip

on each side with progressive sealing effect;

(c) single radial positioned locking system with 1 OR 2 OR

3 screws

Op. 26.07.2012 Dec. 22.10.2012 - TC 1227051

7307.99.00 FITTINGS, TUBE, carbon steel, with OR without seals, having an

internal AND/OR external zinc coating NOT greater than 8 micron,


(a) couplings having a diameter NOT greater than 200 mm;

(b) reducers;

(c) bends;

(d) T junctions;

(e) union connectors;

(f) adaptors

Op. 18.10.2010 Dec. 13.01.2011 - TC 1046729

7307.99.00 FITTINGS, MULTILAYERED WELDED STEEL PIPE, being ANY of the

following:

(a) elbows;

(b) joints;

(c) reducers;

(d) T fittings;

(e) bends;

(f) end caps

Op. 07.06.2010 Dec. 30.08.2010 - TC 1025390

7307.99.00 TERMINATION HEADS, subsea

Op. 05.01.2009 Dec. 27.03.2009 - TC 0946016

7307.99.00 OILWELL CONNECTORS, having ALL of the following:

Tariff Description

===========================================================================


(a) nonhelical interlocking teeth;

(b) metal to metal seals;

(c) diameter NOT less than 50.8 cm

Op. 29.07.2005 Dec. 07.10.2005 - TC 0509995

7307.99.00 FITTINGS, COUPLING, HOSE, quick connect, being ANY of the

following:

(a) male sections;


(c) lever rings;

(d) male plugs;

(e) female caps

Op. 21.12.2007 Dec. 07.03.2008 - TC 0721938

7307.99.00 COUPLINGS, HOSE, QUICK CONNECT, comprising ALL of the following;

(a) male sections;


(c) lever ring

Op. 21.12.2007 Dec. 07.03.2008 - TC 0721939

7307.99.00 FITTINGS, PIPE, being EITHER of the following:

(a) hot tap;

(b) line stop

Op. 21.04.2008 Dec. 11.07.2008 - TC 0804852

7307.99.00 CONNECTORS, HYDRAULIC HOSE, steel

Op. 13.08.2008 Dec. 31.10.2008 - TC 0826255

7307.99.00 FITTINGS, PIPE, forged, integrally reinforced, contoured-insert

vessel or piping branch connections, having a bore size NOT less

than 15 mm and NOT greater than 1 200 mm

Op. 04.09.2008 Dec. 28.11.2008 - TC 0829428

7307.99.00 FITTINGS, ROOF DRAINAGE, galvanized steel, being ANY of the

following:

(a) rainwater outlets;

(b) inclined outlets;

(c) hoppers;

(d) elbows;

(e) s-curves;

(f) hinged outlets;

(g) pipe flaps

including sets of 2 or more of the above

Op. 14.10.2008 Dec. 14.01.2009 - TC 0835300

7307.99.00 FITTINGS AND ADAPTORS, PIPE OR TUBE OR HOSE, carbon steel, with

or without seal, being ANY of the following:

(a) reducing or enlarging bush, hexagon;

(b) caps, solid or swivel;

(c) crosses;

(d) nipples, being ANY of the following:

(i) hexagon;

(ii) barrel;

(iii) plain;

(iv) reducing;

(e) sockets, including reducing and enlarging;

(f) plugs, square head or hex head or internal or external

hexagon;

(g) unions;

(h) tube welds or weld-on's;

(i) tube compression and tube flared fittings

Op. 03.12.2008 Dec. 27.02.2009 - TC 0842546

7307.99.00 FITTINGS, pipe and tube, metric, including sealing rings, bodies and

Tariff Description

===========================================================================


nuts, to specifications DIN 2353 or DIN 3859 in ANY of the

following sizes:

(a) 4 mm;

(b) 6 mm;

(c) 8 mm;

(d) 10 mm;

(e) 12 mm;

(f) 14 mm;

(g) 15 mm;

(h) 16 mm;

(i) 18 mm;

(j) 20 mm;

(k) 22 mm;

(l) 25 mm;

(m) 28 mm;

(n) 30 mm;

(o) 35 mm;

(p) 38 mm;

(q) 42 mm;

(r) 50 mm

Op. 02.12.1993 Dec. 11.04.1994 - TC 9400309

7307.99.00 COUPLINGS, pipe or hose, quick connect (or disconnect), comprising

male and female ring lock couplings, hinged ring band snap lock,

to suit pipes and hoses having an OD of 50 mm or greater

Op. 24.02.1994 Dec. 03.06.1994 - TC 9402433

7307.99.00 FITTINGS, pipe, high pressure, steel, complying with ALL the

following standards:

(a) ASTM A105;

(b) ANSI B16.11;

(c) BS3799

Op. 27.04.1994 Dec. 29.07.1994 - TC 9404403

7307.99.00 BRANCH CONNECTIONS, weld on type, complying with ALL the following

standards:

(a) ASTM A105;

(b) ANSI B31-1 1980;

(c) ANSI B16-9;

(d) BS3351 1971

Op. 27.04.1994 Dec. 05.08.1994 - TC 9404404

7307.99.00 FITTINGS, pipe and tube, including sealing rings, bodies, nuts and

weld cones, having BOTH of the following:

(a) compliance with pressure rating being either LL, L or S to

DIN 2353;

(b) interchangeability of the whole or any component of the

fitting with other fittings or components which comply with

the dimensional specifications set out in DIN 2353,

but NOT including ANY of the following:

(a) stainless steel fittings;

(b) twin ferrule fittings

Op. 25.11.1994 Dec. 14.03.1995 - TC 9409468

7307.99.00 FITTINGS, STEEL, being EITHER of the following:

(a) hose couplings having a female ACME coupling connection within

the range of 44.45 mm to 82.55 mm (both inclusive);

(b) adapters with male ACME connection within the range of

44.45 mm to 82.55 mm (both inclusive)

Op. 14.02.1995 Dec. 20.10.1995 - TC 9501971

7307.99.00 FITTINGS, PIPE, unthreaded, being ANY of the following:

(a) joining rings having a diameter of 80 mm or greater but NOT

exceeding 800 mm;

Tariff Description

===========================================================================


(b) pressed bends of galvanised or mild steel in angles from 7.5

degrees or greater but NOT exceeding 90 degrees and diameter

of 80 mm or greater but NOT exceeding 400 mm;

(c) straight ducting with fully rolled beaded edge having a

diameter of 155 mm or greater but NOT exceeding 160 mm;

but NOT including fittings of stainless steel

Op. 31.08.1995 Dec. 08.12.1995 - TC 9510236

7307.99.00 CLOSURES, PRESSURISED PIPELINE, having ALL of the following:

(a) a cap;

(b) a welding hub, with an integrated semi-dovetailed O-Ring

groove in the face;

(c) capable of horizontal, vertical or angle installations

Op. 22.03.1996 Dec. 28.06.1996 - TC 9604891

7307.99.00 FITTINGS, TUBE, carbon steel, twin ferrule

Op. 17.11.1997 Dec. 23.01.1998 - TC 9710154

7307.99.00 FITTINGS, ON-LINE HYDRAULIC LINE TESTING, being couplers, adaptors

OR stand pipes, working pressures up to 40 MPa in hose sizes 2 mm

and 4 mm

Op. 10.12.1997 Dec. 27.02.1998 - TC 9710916

7307.99.00 GROUND CONES, FLEXIBLE METAL CONDUIT FITTING

Op. 26.02.1998 Dec. 11.05.1998 - TC 9801691

7307.99.00 NIPPLES, LANDING, SUB SURFACE FLOW CONTROL

Op. 01.05.1998 Dec. 17.07.1998 - TC 9803639

7307.99.00 COUPLINGS, SUCKER ROD, 12.7 mm to 28.6 mm (1/2" to 1 1/8")

Op. 05.11.1998 Dec. 15.01.1999 - TC 9809843

7308.10.00 PARTS, MODULAR PANEL BRIDGING, conforming to BS:EN 10025 and

BS:EN 10113, being ANY of the following:

(a) panels;

(b) chord reinforcement;

(c) rakers;

(d) frames;

(e) transoms;

(f) sway brace;

(g) braces;

(h) decks;

(i) kerbs;

(j) in fills;

(k) post ends;

(l) beams;

(m) screw deck clamps;

(n) signs;

(o) plates;

(p) plugs;

(q) links;

(r) extensions;

(s) markers;

(t) diaphragms;

(u) packers;

(v) spikes;

(w) seal kits;

(x) keys;

(y) bars;

(z) tin snips;

(aa) gimlets;

(ab) grillages;

(ac) posts;

(ad) base plates;

Tariff Description

===========================================================================


(ae) toe ramps;

(af) ground beams;

(ag) lugs;

(ah) holdfast pickets and spikes;

(ai) D shackles;

(aj) slings;

(ak) tirfor;

(al) channels;

(am) angles;

(an) walkways;

(ao) stanchions;

(ap) handrails;

(aq) staircases;

(ar) blocks;

(as) sway frames;

(at) rollers;

(au) links;

(av) stool outers;

(aw) struts;

(ax) ties;

(ay) gauges

Op. 05.12.2003 Dec. 31.03.2004 - TC 0315337

7308.30.00 SLIDING DOOR SYSTEM, CAVITY, BRICK WALL, incorporating

overlapping steel mesh

Op. 10.06.2009 Dec. 04.09.2009 - TC 0919622

7308.30.00 GRILLS, SECURITY, metal, retractable, self locking

Op. 31.05.2006 Dec. 11.08.2006 - TC 0609406

7308.40.00 STEEL COMPONENTS, being temporary shuttering AND part of a

removable modular system, including prefabricated grids AND

panels, being soffit bases

Op. 17.02.2014 Dec. 02.07.2014 - TC 1406250

7308.40.00 COMPONENTS, SCAFFOLDING, being ANY of the following:

(a) chainwire rolls;

(b) ledgers;

(c) tie bars;

(d) toe board clips;

(e) wall ties;

(f) wall tie tubes

Op. 13.12.2013 Dec. 10.02.2014 - TC 1405222

7308.40.00 COMPONENTS, SCAFFOLDING, complying with Australian Standard AS

1576.2, being ANY of the following:

(a) double couplers;

(b) double reducers;

(c) swivel couplers;

(d) swivel reducers;

(e) putlog half;

(f) putlog hooks;

(g) putlog full;

(h) putlog blades;

(i) internal joiners;

(j) gravlock beam clamps;

(k) swivel beam clamps

Op. 13.12.2013 Dec. 10.02.2014 - TC 1405226

7308.40.00 SCAFFOLDING COMPONENTS, being ANY of the following:

(a) V-housings;

(b) camlocks;

(c) ledgers;

(d) toe board clamps

Tariff Description

===========================================================================


Op. 13.12.2013 Dec. 10.02.2014 - TC 1405223

7308.40.00 PROPS, HOT DIPPED GALVANISED AND/OR ZINC PLATED, having a rolled

thread on the outer tube

Op. 13.11.2007 Dec. 29.01.2008 - TC 0719361

7308.90 RAILS, elevator guide, weight less than 6 kg/m or exceeding

26 kg/m

Op. 28.02.1984 Dec. 28.02.1984 - TC 8437468

7308.90 CRASH CUSHIONS, roadside hazard, energy absorbing, meeting NCHRP

230 Test tolerances

Op. 18.11.1988 Dec. 19.10.1990 - TC 8810530

7308.90.00 PARTS, FORMWORK AND/OR SAFETY SCREEN, VERTICAL CLIMBING SYSTEM,


(a) beams;

(b) braces;

(c) brackets;

(d) frames;

(e) latches;

(f) masts;

(g) supports;

(h) bracing tubes;

(i) struts;

(j) adapters;

(k) connectors;

(l) extensions

Op. 01.09.2015 Dec. 08.02.2016 - TC 1533598

7308.90.00 CLIPS, ROOF AND/OR WALL SHEETING

Op. 13.03.2015 Dec. 25.05.2015 - TC 1510243

7308.90.00 BEAMS, FLOORING SUPPORT, steel, assembled OR unassembled, having


(a) beam lengths NOT less than 8 200 mm;

(b) complete penetration butt welded steel plate complying with

Australian Standard AS 4100-1998, 9.7.2.7;

(c) bevelled beam ends, with end plates attached,

with OR without ANY of the following:

(i) nuts;

(ii) bolts;

(iii) washers

Op. 10.11.2014 Dec. 15.04.2015 - TC 1439131

7308.90.00 PUSH BACK PALLET RACKING SYSTEM, including BOTH of the following:

(a) trolleys;

(b) support beams

Op. 03.12.2014 Dec. 02.03.2015 - TC 1442731

7308.90.00 PARTS, DEMOUNTABLE FLOOD CONTROL CONTAINMENT SYSTEM, conforming

to British Standard PAS 1188-4, (BSI PAS 1188-4), being ANY of

the following:

(a) supports;

(b) corner posts;

(c) braces;

(d) support covers

Op. 06.11.2014 Dec. 28.01.2015 - TC 1438761

7308.90.00 PARTS, FLARE GAS STACK, LNG CONDITIONING, being ANY of the

following:

(a) stack tube segments with OR without internal low pressure

riser sections;

(b) external high pressure riser sections with OR without riser

Tariff Description

===========================================================================


guide supports;

(c) riser bracing supports;

(d) platforms;

(e) ladders;

(f) handrails

Op. 04.09.2014 Dec. 16.01.2015 - TC 1431532

7308.90.00 ACCESS BOXES OR CUBES OR PRISMS, rectangle, steel, modular,

including ANY of the following:

(a) connector plates;

(b) end panels;

(c) brackets;

(d) cross beams;

(e) spreader;

(f) steel plate supports

Op. 05.09.2014 Dec. 01.12.2014 - TC 1431647

7308.90.00 GUIDE RAILS, iron AND/OR steel, cold-drawn, having a rail length

less than 5.5 m, with OR without fishplates

Op. 17.04.2014 Dec. 14.07.2014 - TC 1413672

7308.90.00 SHORING, steel, modular, hydraulic adjustable, including ALL of

the following:

(a) braces;

(b) struts;

(c) beams

Op. 15.10.2013 Dec. 03.03.2014 - TC 1334324

7308.90.00 FARROWING CRATES, PIGGERY, unassembled, having ALL of the

following:

(a) compressed fibre panelling;

(b) steel crates;

(c) steel fencing;

(d) plastic covers

Op. 20.08.2013 Dec. 18.11.2013 - TC 1328433

7308.90.00 PARTS, STRUCTURAL STEEL SECTIONS, WHARF, being EITHER of the

following:

(a) topside modules NOT less than 75 tonnes;

(b) dolphins NOT less than 25 tonnes

Op. 17.10.2013 Dec. 17.10.2013 - TC 1332986

7308.90.00 STRUCTURES, STEEL, MARINE BERTHING, being ANY of the

following:

(a) marine piles NOT less than 750 mm diameter;

(b) dolphins NOT less than 25 tonnes;

(c) topside modules NOT less than 75 tonnes

Op. 17.10.2013 Dec. 17.10.2013 - TC 1332984

7308.90.00 SOLDIERS, FORMWORK, having ALL of the following:

(a) length NOT greater than 3 650 mm;

(b) width NOT less than 220 mm;

(c) hole diameter NOT greater than 105 mm

Op. 19.04.2013 Dec. 05.08.2013 - TC 1313426

7308.90.00 PARTS, STRUCTURAL STEEL, COAL PLANT OR IRON ORE PLANT, being


(a) rolled, hollow or welded sections;

(b) beams;

(c) grating,

(d) stairways and/or treads;

(e) plates;

(f) handrails (with or without kick plates);

Tariff Description

===========================================================================


(g) stanchions;

(h) purlins and girts;

(i) packing and shims;

(j) guards;

(k) legs;

(l) stringer and ground modules;

(m) frames;

(n) wear liners;

(o) gantries

Op. 30.04.2013 Dec. 11.06.2013 - TC 1319269

7308.90.00 STRUCTURES, STEEL, GAS FUELLED POWER PLANT, being EITHER of the

following:

(a) exhaust gas stack;

(b) radiator platform

Op. 13.03.2013 Dec. 18.06.2013 - TC 1309205

7308.90.00 WATER DIVERSION OR DAM BARRIERS, mobile, including ALL Of the

following:

(a) steel A shaped frames;

(b) steel connecting rods;

(c) plywood AND/OR aluminium panels;

(d) plastic membrane sheets;

(e) steel clips AND chains;

(f) storage crates AND wooden pallets

Op. 19.02.2013 Dec. 02.05.2013 - TC 1306230

7308.90.00 ACCESS FLOORING, having BOTH of the following:

(a) steel encapsulated chipboard core panels AND/OR calcium

sulphate core panels;

(b) pedestals, including a head, base and gasket

Op. 23.10.2012 Dec. 14.01.2013 - TC 1240491

7308.90.00 PARTS, ACCESS FLOORING, being ANY of the following:

(a) steel encapsulated chipboard core panels AND/OR calcium

sulphate core panels;

(b) pedestals, including a head, base and gasket;

(c) stringers, complete with gasket

Op. 23.10.2012 Dec. 14.01.2013 - TC 1240492

7308.90.00 STRUCTURES, STEEL, GAS STACK, VENT OR FLARE, including ALL of

the following:

(a) gas stack tubes;

(b) bracing;

(c) beams;

(d) ladders;

(e) handrails

Op. 15.10.2012 Dec. 07.01.2013 - TC 1239299

7308.90.00 PARTS, FOUNDATION, VERTICAL ROLLER MILL, CEMENT GRINDING, being


(a) multi-drive foundation frames;

(b) thrust bearing gearbox base plates;

(c) gearbox plate recess boxes;

(d) anchorage base plates;

(e) mill foundation anchor plates;

(f) mill foundation slide rails;

(g) rocker arm support pedestals;

(h) assembly and alignment equipment having ALL of the

following:

(i) I-beams;

(ii) threaded rod;

(iii) compensation plates;

Tariff Description

===========================================================================


(iv) plates,

(i) anchor bolt recess boxes;

(j) I-beams being foundation embedments

Op. 30.08.2012 Dec. 21.11.2012 - TC 1232381

7308.90.00 MARINE BERTH MODULES, having ALL of the following:

(a) width NOT less than 16 m;

(b) length NOT less than 39 m;

(c) weight NOT less than 400 t

Op. 01.08.2012 Dec. 15.10.2012 - TC 1227730

7308.90.00 PARTS, MODULAR MULTIDIRECTIONAL FRAMEWORK, conforming to

European Standard 13480 (EN:13480) and European Standard

1993 (EN:1993), being ANY of the following:

(a) adapters;

(b) bases;

(c) beams;

(d) ends;

(e) joints;

(f) plates;

(g) spider clamps

Op. 26.06.2012 Dec. 12.09.2012 - TC 1222230

7308.90.00 ROOFING, MODULAR, being ANY of the following:

(a) roof cassettes;

(b) ridge cassettes;

(c) roof beams;

(d) roof girders;

(e) ridge supports;

(f) beam stiffeners;

(g) tubular stiffeners;

(h) lattice beam connectors;

(i) wedges;

(j) clamping plates;

(k) roof supports

Op. 29.12.2011 Dec. 26.03.2012 - TC 1142644

7308.90.00 PARTS, MARINE WHARF, being steel pile caps

Op. 16.11.2011 Dec. 30.01.2012 - TC 1138231

7308.90.00 PANELS, INSULATING, consisting of polyurethane inner core with

galvanised steel sheeting BOTH sides, having BOTH of the

following:

(a) steel sheet thickness NOT less than 0.4 mm;

(b) polyurethane thickness NOT less than 20 mm

Op. 27.07.2009 Dec. 09.10.2009 - TC 0926917

7308.90.00 MARINE PILINGS, steel, having ALL of the following:

(a) thickness NOT less than 20 mm;

(b) length NOT less than 28.5 m;

(c) diameter NOT less than 900 mm;

(d) maximum of one splice per piling;

(e) maximum straightness difference of 1 mm per metre over

entire length

Op. 30.04.2009 Dec. 24.07.2009 - TC 0914435

7308.90.00 STRUCTURES, FACADE, woven mesh, stainless steel

Op. 18.04.2007 Dec. 06.07.2007 - TC 0705685

7308.90.00 PARTS, FORMWORK, PANEL WALL SYSTEM, being ANY of the

following:

(a) adapters;

(b) add-on pieces;

(c) adjustment pieces;

Tariff Description

===========================================================================


(d) angles;

(e) bases;

(f) braces;

(g) brackets;

(h) clamps;

(i) cones;

(j) connector assemblies, comprising both ends and clamps;

(k) connectors;

(l) hinged and/or fixed corners;

(m) cross-bars;

(n) ends;

(o) fasteners;

(p) form strips;

(q) frames;

(r) guardrails;

(s) joints;

(t) locating pins;

(u) mid rails;

(v) panels;

(w) plates;

(x) platform beams;

(y) platforms;

(z) plugs;

(aa) posts;

(ab) props;

(ac) railing;

(ad) spindles;

(ae) spacer and/or centre tubes;

(af) stiffeners;

(ag) stop ends;

(ah) struts;

(ai) tie rods;

(aj) tighteners;

(ak) transport hooks;

(al) triangular wedges;

(am) waler spanners;

(an) walers;

(ao) wedges

Op. 13.11.2007 Dec. 29.01.2008 - TC 0719350

7308.90.00 PARTS, FORMWORK, SOLDIER SYSTEM, being ANY of the following:

(a) adapters;

(b) bases;

(c) braces;

(d) brackets;

(e) clamps;

(f) clips;

(g) connectors;

(h) couplers;

(i) edge angles;

(j) fork arms;

(k) fork heads;

(l) guardrails;

(m) jacks;

(n) lifting loops and/or plates and/or brackets;

(o) pivots;

(p) plates;

(q) plumbing braces;

(r) posts;

(s) shoring adapters;

(t) soldiers, having holes NOT greater than 70 mm

diameters;

(u) spreader connections and/or beams and/or adaptors;

(v) stabilisers;

Tariff Description

===========================================================================


(w) turnbuckles;

(x) u-heads;

(y) brackets (high load washer);

(z) web stiffeners;

(aa) wheel and bracket assemblies, comprising both wheels and

brackets

Op. 13.11.2007 Dec. 29.01.2008 - TC 0719351

7308.90.00 PARTS, MUSHROOM SUBSTRATE PASTEURIZATION TUNNELS OR BUILDINGS,


(a) connection plates;

(b) beams;

(c) pillars;

(d) panels;

(e) profile sheets;

(f) walls;

(g) roofing

Op. 07.11.2008 Dec. 30.01.2009 - TC 0838882

7308.90.00 SHAPES AND PROFILES, of puddled wrought iron

Op. 13.01.1994 Dec. 22.04.1994 - TC 9401293

7308.90.00 CHILD SAFETY GATES OR EXTENSIONS, DOMESTIC, internal

Op. 29.09.2000 Dec. 15.12.2000 - TC 0008230

7308.90.00 GUIDE RAILS, LIFT, hot rolled, bright drawn and planed

Op. 22.02.2001 Dec. 04.05.2001 - TC 0101755

7308.90.00 PARTS, ACCESS FLOORING, being ANY of the following:

(a) steel cementitious floor panels;

(b) pedestals;

(c) stringers;

(d) pedestal heads

Op. 28.07.2004 Dec. 11.10.2004 - TC 0407789

7308.90.00 ACCESS FLOORING, comprising ALL of the following:

(a) steel cementitious floor panels;

(b) pedestals;

(c) stringers;

(d) pedestal heads

Op. 05.08.2004 Dec. 18.10.2004 - TC 0408063

7309.00.00 TANKS, STORAGE, stainless steel, unassembled, having BOTH of the

following:

(a) panel lengths NOT less than 2 m;

(b) NOT less than 8 panels for each tank,

with OR without ANY of the following:

(i) tank covers;

(ii) internal guide rails;

(iii) steel reinforced floor panels;

(vi) mounting plates AND support poles;

(v) steel panels with manholes AND manhole covers;

(vi) valves;

(vii) steel OR polyvinyl chloride(PVC) pipes

Op. 26.05.2016 Dec. 22.08.2016 - TC 1618988

7309.00.00 TANKS, PICKLING, acid OR flux, having BOTH of the following:

(a) composite synthetic ceramic AND glass fibre laminate wall

panels;

(b) steel frames

Op. 15.12.2015 Dec. 07.03.2016 - TC 1545049

7309.00.00 FURNACE DRUMS, METALLICS RECOVERY, having ALL of the

Tariff Description

===========================================================================


following:

(a) gross capacity NOT greater than 2 550 kg;

(b) bolt-on lids AND seals with spout cover cap;

(c) lid fixing plates

Op. 17.11.2015 Dec. 10.02.2016 - TC 1541859

7309.00.00 SILOS, bolted modules, steel, whether OR

not assembled, with OR without stairs, having ALL of the

following:

(a) piping AND/OR hoses with OR without connectors;

(b) flow control valves;

(c) level measurement microwave sensor including display;

(d) capacity NOT less than 155 cubic metres and NOT greater

than 4 500 cubic metres

Op. 21.04.2015 Dec. 31.08.2015 - TC 1515310

7309.00.00 TANKS, HOT WATER, having ALL of the following:

(a) welded steel plate construction;

(b) insulation AND cladding thickness NOT less than 200 mm;

(c) temperature capacity NOT less than 5 degrees Celsius and

NOT greater than 95 degrees Celsius;

(d) pressure capacity NOT less than 56 mbar;

(e) water capacity NOT less than 100 000 L

Op. 20.12.2013 Dec. 10.04.2014 - TC 1342075

7309.00.00 TANKS, WASTE WATER, glass lined steel, having BOTH of the

following:

(a) diameter NOT less than 4 200 mm;

(b) height NOT less than 5 600 mm

Op. 06.11.2013 Dec. 03.02.2014 - TC 1337391

7309.00.00 CONTAINMENT SYSTEM, TANK, WATER AND/OR BRINE, expandable,

portable, including ALL of the following:

(a) tank wall panels;

(b) liner clamp;

(c) wind ring;

(d) maximum capacity NOT greater than 21,005 cubic metres;

(e) maximum diameter NOT greater than 150 metres

Op. 09.04.2013 Dec. 25.09.2013 - TC 1312233

7309.00.00 TANKS, ION EXCHANGE, with OR without platforms AND ladders

Op. 17.06.2011 Dec. 12.09.2011 - TC 1119444

7309.00.00 TANKS, GERMINATING AND KILNING, BARLEY MALT, steel,

prefabricated, having a minimum batch load capacity NOT less

than 360 tonne

Op. 06.08.2007 Dec. 12.10.2007 - TC 0712554

7309.00.00 TANKS, COLD WATER, DIAPHRAGM PRESSURE, having a capacity

exceeding 300 L and NOT greater than 500 L

Op. 07.03.2008 Dec. 16.05.2008 - TC 0803919

7309.00.00 SURGE TANKS, VERTICAL, OIL AND GAS WELL TESTING

Op. 06.08.2008 Dec. 24.10.2008 - TC 0825351

7309.00.00 DUST AND FILLER SILO MODULE, ASPHALT PLANT

Op. 05.09.2008 Dec. 12.12.2008 - TC 0829721

7309.00.00 RECLAIMED ASPHALT PAVEMENT (RAP) MODULE, ASPHALT PLANT

Op. 05.09.2008 Dec. 28.11.2008 - TC 0829756

7309.00.00 COLD FEED MODULE, ASPHALT PLANT

Op. 05.09.2008 Dec. 28.11.2008 - TC 0829971

Tariff Description

===========================================================================


7310.10.00 TANKS, COLD WATER, DIAPHRAGM PRESSURE, having a capacity NOT

less than 50 L and NOT greater than 300 L

Op. 06.03.2008 Dec. 16.05.2008 - TC 0803685

7310.10.00 KEGS, BEVERAGE, stainless steel, with OR without spears

Op. 26.06.2003 Dec. 15.09.2003 - TC 0307781

7310.29 CONTAINERS, cryogenic, insulated or vacuum wall, using liquefied

gas as a refrigerant medium to store goods (OTHER THAN gas),

at a temperature below - 100 degrees C

Op. 28.02.1984 Dec. 28.02.1984 - TC 8341467

7310.29.00 KEGS, BEVERAGE, stainless steel, having a volume capacity less

than 50 L, with OR without keg spears

Op. 14.05.2014 Dec. 04.08.2014 - TC 1416208

7310.29.00 TINS, PACKAGING, tin coated, with

or without hinged lid

Op. 15.09.2009 Dec. 27.11.2009 - TC 0934614

7310.29.00 TANKS, COLD WATER, diaphragm pressure, having a volume capacity

NOT greater than 50 L

Op. 06.07.2009 Dec. 18.09.2009 - TC 0923307

7310.29.00 TANKS, COLD WATER, diaphragm pressure, having a capacity less

than 50 litres

Op. 04.06.2009 Dec. 28.08.2009 - TC 0918884

7310.29.00 JERRY CANS, conforming to Australian/New Zealand Standard

2906:2001 (AS/NZS 2906:2001)

Op. 28.01.2009 Dec. 19.06.2009 - TC 0902741

7310.29.00 TINS, NOVELTY, having less than 220 grams of confectionery

and/or bakers wares

Op. 15.09.2005 Dec. 25.11.2005 - TC 0512191

Documents

7301 to 7310.29.00