8mm FRAMED PLUS SLIDING

This product is universal, not handed

WITH SIDE PANELRefer To Sheet 13 For Relevant Product Codes

VictoriaPlum.com0344 804 48 48

1

BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION

1) General Information

2) Additional Notes

Please inspect this product upon delivery, any missing parts or manufacturing

defects must be reported immediately to the supplier. Damage or defects reported

later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS - AVOID

HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.

Glass breakage claims will not be accepted after the product has been unpacked.

Please note: Aluminium is a soft metal, and undergoes a series of extrusion,

fabrication, polishing and anodising processes in order to create your finished

shower enclosure. Some light surface marks are normal, and is a result of the

manufacturing processes. Quality control has ensured that this item is of a good

standard, and is fit for purpose.

Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.

Note: this product is heavy and may require two people to install.

This product is heavy and may require two people to install.

TOOLS REQUIRED

Ø3mm Drill bit

Ø6mm Drill bit

Pencil

Spirit level

Tape measure

DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE

Drill

Flat-headScrewdriver

Cross headScrewdriver

Mallet

Silicone Sealant

PZ1

2

8x Wall Plugs

2x Wall Post Cover caps

2x Wall Profiles

2x Cover Strip

3x Vertical Covers

1x Side Panel

1x Corner Post Cover Cap

9x Screws 4x12

(9) 1x Corner Post Cover Strip

8x Screws 4x40

1x Upright Magnet Profile

1x Magent Seal

2x Top And Bottom Profiles

2x Top Rollers

1x Moving Panel

1x Supplied Separately)Handle (

2x Bottom Rollers

1x Moving Panel Seal

1x Fixed Panel Seal

2x Bottom Seal

1x Fixed Panel

8x Screws 4x30

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(10)

(11)

(12)

(13)

(14)

(15)

(16)

(17)

(18)

(19)

(20)

(21)

(22)

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (15)(14)

(19)(17) (18)(16) (20) (21) (22)

ASSEMBLY INSTRUCTIONS - DRAWING

76

0/8

00

/90

0

10

10

10

10

10101200/1400/1600

10

10

10

3

1200/1400/1600

10

10

10

10

THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.

ASSEMBLY INSTRUCTIONSIf you require help, we advise you to contact a competent plumber Installation Steps

FITTED SLIDING DOOR AND SIDE PANEL DRAWING

Installation Steps

4

Round ScrewST4X40

1a 1b 1c

2a 2b 2c

3a

3b

1b

1c

2b

2c

3a

3b

MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS

SHOWER PANEL / DOOR,

Step 1 ASSEMBLE FRAME AND FIXED PANEL

VIEW FROM INSIDE

VIEW FROM INSIDE

1a

2a

5

10mm 10mm

Step 2 SLIDE WALL PROFILE ON TO FIXED PANEL

Step 3 MARK WALL FIXING POSITIONS

VIEW FROM INSIDE

6

Round ScrewST4X30

VIEW FROM INSIDE

VIEW FROM INSIDE

Step 4 DRILL WALL HOLE

Step 5 SCREW THE WALL PROFILE TO THE WALL

6mm Drill Bit

7

Round ScrewST4X12

3mm Drill Bit

Step 6 SECURING THE WALL PROFILES + COVER STRIP

Step 7 FITTING THE TOP AND BOTTOM ROLLERS

VIEW FROM INSIDE

VIEW FROM INSIDE

L=0~20mmL 5mm/R≥ ≥10mm

R

L 5mm/R≤ ≥15mm

1

2

3

8

Ensure wall profiles are plumb. Adjust enclosure to be square and level. Wheels should be adjusted to square the doors andensure smooth running,using the adjusting screws underneath the top rollers.

Fixed PanelDoor Panel

1 2

3 4

1a

1b

2

3

1a

1b

23

Step 8 FITTING THE MOVING PANEL ON TO THE PROFILE

Step 9 FITTING THE SEALS VIEW FROM INSIDE

VIEW FROM INSIDE

999

Step 10 FITTING THE TOP CAPS AND HANDLE

Step 11 SILICONE THE OUTSIDE EDGES

Allow 24 hours for silicone to dry before use. Silicone on the

outside edge only, NOT THE INSIDE

10mm

10

6mm Drill Bit

CORNER INSTALLATION WITH SIDE PANEL

Step 1

Step 3

Step 2 DRILL WALL HOLE

Step 4 FITTING THE SIDE PANEL

VIEW FROM INSIDE

MARK THE CORRECT DRILL HOLE POSITIONS ON THE WALL

SLIDE WALL PROFILE ON TO THE SIDE PANEL

FOLLOW SLIDING DOOR STEPS 1 & 2 FIRST THEN COMBINE WITH THESE STEPS

6mm Drill Bit

11

Round ScrewST4X30

3mm Drill Bit

Step 5 SCREW THE WALL PROFILE TO THE WALL

Step 6 SECURING THE SIDE PANEL AND PROFILE COVER STRIP

VIEW FROM INSIDE

VIEW FROM INSIDE

VIEW FROM INSIDE

VIEW FROM INSIDE

3mm Drill Bit

Round ScrewST4X12

Round ScrewST4X12

2

1

3

4

5

6

L=0~20mmL 5mm/R≥ ≥10mm

R

L 5mm/R≤ ≥15mm

Step 7 FITTING THE TOP CAPS

12

Step 8 SILICONE THE OUTSIDE EDGES

Allow 24 hours for silicone to dry before use. Silicone on the

outside edge only, NOT THE INSIDE

13

Product name: 8mm Framed Plus Sliding and Side Panel

Product code: LSD1001 LSD1201 LSD1401 LSD1601 LSD1701 LSP701 / / / / /

Customer help line number: 0344 804 48 48

CARE AND MAINTENANCE

COMMITMENT TO QUALITY

1) AFTER CARE INSTRUCTIONS

2) MAINTENANCE

Regularly clean your shower product with warm soapy water

Clean the plastic parts with a cloth and mild detergent. Never

use any abrasive creams, dissolvents, acetone or detergents

and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained

in these instructions. The supplier reserves the right to introduce

technical changes without notice.

It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you

firstly contact a competent plumber. However we understand that

this may not always be the case, so should you experience

any problems please contact our customer services quoting

the following:

to prevent lime scale build up. Do not use abrasive cleaning

fluids or materials, or strong chemical cleaners as this will

damage the product surface.

LSP801 / LSP901

14

INSTALLERS NOTES

The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.

We suggest you take it to the local landfill site and discard in the designated bins.

Victoria Plum Limited, Bridgehead Business Hessle, HU13 0DG

Park

16

EN 14428:2004+A1:2008

DOP No.:J160415002

Shower enclosures with aluminiumprofiles and safety glass

Essentialcharacteristics

Performance Harmonisedtechnical

specificationCleanability

Impactresistance/shatter

properties

Pass

Pass

PassDurability

Clause 4.2 of EN14428:2004+A1:

2008Clause 4.3 of EN14428:2004+A1:

2008Clause 4.4 of EN14428:2004+A1:

2008

V01.06 2016.