904XX Operations Manual - Spacelabs Healthcaremanuals.spacelabshealthcare.com/wp-content/uploads/2013/10/070... · ... Clinical Browser, Data Shuttle, Flexport, Inte sys, Mermaid,

Flexport System Interface904XX

Operations Manual070-1148-00 Rev. J

®

©2008 Spacelabs Healthcare

All rights reserved. Contents of this publication may not be reproduced in any form without the written permission of Spacelabs Healthcare. Products of Spacelabs Healthcare are covered by U.S. and foreign patents and/or pending patents. Printed in U.S.A. Specifications and price change privileges are reserved.

Spacelabs Healthcare considers itself responsible for the effects on safety, reliability and performance of the equipment only if:

• assembly operations, re-adjustments, modifications or repairs are carried out by persons authorized by Spacelabs Healthcare, and

• the electrical installation of the relevant room complies with the requirements of the standard in force, and

• the equipment is used in accordance with the operations manual.

Spacelabs Healthcare will make available, on request, such circuit diagrams, component part lists, descriptions, calibration instructions or other information which will assist appropriately qualified technical personnel to repair those parts of the equipment which are classified by Spacelabs Healthcare as field repairable.

Spacelabs Healthcare is committed to providing comprehensive customer support beginning with your initial inquiry through purchase, training, and service for the life of your Spacelabs Healthcare equipment.

CORPORATE OFFICES

U.S.A.

Spacelabs Healthcare, LLC5150 220th Ave SEIssaquah, WA 98029Telephone: 425-657-7200Telephone: 800-522-7025Fax: 425-657-7212

Authorized EC Representative UNITED KINGDOM

Spacelabs Healthcare, Ltd.Beech House, Chiltern CourtAsheridge Road, CheshamBuckinghamshire HP5 2PXTelephone: 44 (0) 1494 784422Fax: 44 (0) 1494 794414

BirthNet, Clinical Browser, Data Shuttle, Flexport, Intesys, Mermaid, MOM, Multiview, PCIS, PCMS, PrintMaster, Quicknet, Sensorwatch, TRU-CAP, TRU-CUFF, TruLink, Ultralite, Ultraview, Ultraview Care Network, Ultraview Clinical Messenger, Ultraview Digital Telemetry, Ultraview SL, Uni-Pouch, UCW, Varitrend and WinDNA are trademarks of Spacelabs Healthcare.

Other brands and product names are trademarks of their respective owners.

Caution:US Federal law restricts the devices documented herein to sale by, or on the order of, a physician.

Before use, carefully read the instructions, including all warnings and cautions.

Rx Only

!

Table of Contents

Contents Page
Introduction
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Flexport System Interface Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2Supporting Data Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3Help Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Abbott Lifecare 4, 4P, or MicroDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6Disconnecting a Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16Noting an Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16Displaying Infusion History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

Alaris IVAC 560/570/599Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7Disconnecting a Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17Noting an Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17Displaying Infusion History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

Alaris 980C/PC-1/PC-2/PC-4Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6Pump address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7Disconnecting a Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17Noting an Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17Displaying Infusion History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Bard CritiCoreDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Flexport System Interface Operations Manual i

Table of Contents

Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9

Baxter-Edwards ExplorerDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

Baxter Flo-Gard 6201/6301Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5Disconnecting a Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16Noting an Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17Displaying Infusion History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-18Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20

Bear 1000Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8Viewing Ventilator Mode History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13

Biochem International BCI 9000Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8Selecting a Waveform Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10

Flexport System Interface Operations Manual ii

Table of Contents

Braun Fluid Management SystemDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7Disconnecting a Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-17Noting an Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-17Displaying Infusion History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-18Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-19Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20

Criticare 504Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-9

Criticare POET 601Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5Viewing Trends. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7

Criticare POET-II 602-3Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-9Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-10

Criticare POET IQ2Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-7Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-10

Flexport System Interface Operations Manual iii

Table of Contents

Critikon Dinamap 1846 and 8100-SeriesDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5Displaying Heart Rate Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-6Displaying New or Previous Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-6Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7Printing NIBP Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-8

Datex Engström Erica/Elvira VentilatorDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-4Display Detail — Erica . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-6Display Detail — Elvira . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-7Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-8Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-9Viewing Ventilator Mode History (Elvira only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-10Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-10Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-12Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-12Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-12Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-13

Datex Normocap CD2-02/CD-200Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-11

Datex UltimaDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-8Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-11

Dräger CatoDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-6

Flexport System Interface Operations Manual iv

Table of Contents

Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-8Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-11Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-11

Dräger Cicero BDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-7Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-9

Dräger Cicero EMDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-11

Dräger Evita II, Evita II Dura, and Babylog 8000Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-9Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-10Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-11Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-11Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-11Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-12

Dräger Evita 4Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-8Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-9Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-9Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-11

Flexport System Interface Operations Manual v

Table of Contents

Dräger Evita 4/XLDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-8Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-9Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-9Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-11

Dräger Irisa/EvitaDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-6Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-6Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-7

Dräger Narkomed 2B and 2CDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-8Freezing the Waveform on the Display (Narkomed 2C Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-10

Dräger Narkomed 3, 4, and GSDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-9Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-10

Edwards Vigilance IDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-7Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-7

Flexport System Interface Operations Manual vi

Table of Contents

Storing a CCO Value as a Bolus CO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-9

Edwards Vigilance IIDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-7Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-8Storing a CCO Value as a Bolus CO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-9

Edwards VigileoDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-7Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-7Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-8

Engström EAS 9000Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-11

GE Ohmeda 5200/5210Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-6Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-6Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-8

GE Ohmeda 5250Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-6

Flexport System Interface Operations Manual vii

Table of Contents

Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-9

GE Ohmeda 7800/7810Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-6Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-7Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-8

GE Ohmeda Care-Plus/Infant WarmerDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-6Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-7Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-8

GE Ohmeda Rascal IIDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-9Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-9

Hamilton Amadeus/Veolar/Galileo/Raphael XTCDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-7Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-7Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-9

Infrasonics Adult Star 2000Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-7

Flexport System Interface Operations Manual viii

Table of Contents

Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-7Viewing Ventilator Mode History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-8Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-10

Maquet Siemens Servo 300Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-4Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-5Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-7Viewing the Ventilator Mode History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-7Viewing Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-8

Maquet Siemens Servo 900Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-4Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-5Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-7Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-8

Masimo RadicalDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-9Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-9

Mortara ELI 100/STMDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-5Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-6Adjusting the Waveform Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-7Selecting a Rhythm Lead Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-9

Newport Medical Instruments E150/E200Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-3

Flexport System Interface Operations Manual ix

Table of Contents

Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-7Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-8Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-9

Oridion VitalCapDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-6Silencing Alarm Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-7Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-9Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-11

OSI OpticalCAMDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-4Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-5Selecting a Unit of Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-5Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-5Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-6

PhysioFlexDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-6Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-9

PiCCODirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47-3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47-4Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47-5Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47-5Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47-6

Radiometer TCM3Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-4

Flexport System Interface Operations Manual x

Table of Contents

Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-6Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-6Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-7

Respironics Novametrix EspritDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-7Viewing Ventilator Mode History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-8Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-9

Respironics-Novametrix 7300/7600Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-7Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-8Display Detail - FLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9Display Detail - PAW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-10Display Detail - CO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-12Display Detail - NICO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-13Display Detail - SpO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-14Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-16Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-17Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-17Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-19Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-19Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-19

Respironics Novametrix 840/860Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-6Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-6Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-7

Respironics Novametrix 1260/1265Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-6Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-10

Flexport System Interface Operations Manual xi

Table of Contents

Respironics Novametrix 2001Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53-5Viewing the Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53-6Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53-7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53-9

Respironics Novametrix 7000/7100Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-1Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-2Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-2Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-3Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-5Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-5Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-7Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-8

SenTec Digital MonitorDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56-8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56-10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56-10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56-10

Smiths Graseby 3000Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57-3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57-4Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57-5Disconnecting a Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57-15Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57-15Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57-16

Tyco Nellcor N-395/N-595/N-600Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-6Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-9

Flexport System Interface Operations Manual xii

Table of Contents

Tyco Nellcor N-1000Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-1Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-2Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-2Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-3Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-4Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-5Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-5Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-6

Tyco Nellcor N-2500Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-6Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-6Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-8

Tyco Nellcor N6000Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-6Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-6Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-9

Tyco Nellcor Symphony N3000Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-6Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-9

Tyco Puritan Bennett 840Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-7Viewing Ventilator Mode History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-8Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-9

Flexport System Interface Operations Manual xiii

Table of Contents

Tyco Puritan Bennett 7200A/AEDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-7Viewing Ventilator Mode History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-8Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-11

Transonics HT-107Directory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65-3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65-4Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65-5Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65-6Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65-7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65-7

VIASYS Ventilator, VelaDirectory of Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-1Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-4Screen Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-7Alarm Recordings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-7Entering Setup Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-8Printing the Current Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-11

Flexport System Interface Operations Manual xiv

Introduction

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Flexport System Interface Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Supporting Data Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Help Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
OverviewThe Flexport® system interface provides access to monitoring data at the patient bedside. It enables data from compatible third-party peripheral devices such as ventilators, multigas analyzers, pulse oximeters, NIBP monitors, IV pumps, incubators, and capnographs to be displayed on Spacelabs Healthcare monitors.

The Flexport system interface provides current numeric data, alarm information, and selected waveforms to the Spacelabs Healthcare monitor, enables you to print the current display, and can support data transfer via the Data Shuttle® option (refer to Supporting Data Transfer on page 1-3).

Once device data is in the Spacelabs Healthcare monitor, it becomes an integral part of the monitoring system and can be communicated over the network to other locations providing alarms, centralized display, trending, and documentation capabilities at remote locations.

Flexport System Interface BasicsThe interface uses RS-232 serial communications to collect data and then transmits the data, via synchronous data link control (SDLC) communications, to the Spacelabs Healthcare monitor.

The Flexport system interface has a male, 9-pin, SDLC connector at one end and either a female, 6-pin, modular jack or a female, 8-pin receptacle at the other end (refer to Figure 1-1). The interface contains no operator controls. Power to the interface is provided by the Spacelabs Healthcare monitor through the SDLC connection.

Figure 1-1: Flexport system interface

9-pin SDLC connector 6-pin modular jack 8-pin receptacle

Flexport System Interface Operations Manual 1-1

Introduction

SetupThe Flexport system interface uses two cables:

• The “L-shaped” SDLC cable connects the Spacelabs Healthcare monitor to the Flexport system interface.

• The modular cable has modular connectors (similar to U.S. telephone connectors) at each end and connects the Flexport system interface to the peripheral device.

Figure 1-2: Flexport system interface connectors

The transition connector adapts the modular cable to the peripheral device.

The SDLC terminator is used at one end of the SDLC cable when the SDLC cable is not used to connect additional Spacelabs Healthcare products to the Spacelabs Healthcare monitor.

Note:• After receiving your Flexport installation kit, contact your Field Service Engineer or your Biomedical

Department to install your SDLC cable and terminator on your monitor or module housing.

• Additional installation details are available in the 90485/86/91/99 Module Housings and Power Supplies Service Manual (P/N 070-0680-xx, located on CD-ROM 084-0700-xx).

SDLC cable SDLC terminatortransition connector


Introduction

Connecting the Flexport System InterfaceThe Flexport system interface connects to a peripheral device such as a ventilator, IV pump, multigas analyzer, or capnograph as shown in Figure 1-3.

Note:Your device setup may differ from the graphic shown here. Refer to the chapter corresponding to your peripheral device for specific setup information.

Figure 1-3: Flexport system interface connections

Caution:Attach only Spacelabs Healthcare-approved accessories to RS-232 connectors.

Supporting Data TransferIf you use the interface with a Spacelabs Healthcare monitor that includes a multi-parameter module with the Data Shuttle option, you can use that module’s data transfer capability to pass data from one monitor to another. To ensure the integrity of your data, you must finish data collection before you begin the transfer process. To end data collection, disconnect the modular cable from the interface.

For further information on the Data Shuttle option, refer to the Bedside Monitors chapter in the Ultraview SL® Operations Manual (P/N 070-1150-XX, located on CD-ROM 084-1101-xx).

SpacelabsHealthcare

monitor

SDLCcable

SDLCterminator

transitionconnector

modularcable peripheral

device

systemFlexport

interface


Introduction

Help MessagesIf you are in doubt about a key, touch the monitor HELP key, and then touch the key in question. The monitor will display a brief description of its function.


Abbott Lifecare 4, 4P, or Micro

Directory of Keys

IV

IV - MAIN MENU

HISTORY SETUP EVENT DISCONNECT PRINT

Refer to page 2-2

IV - DISCONNNECTPUMP

1PUMP

2PUMP

3PUMP

4 ALL

IV - DISCONNNECT PUMP 1?YES NO

IV - EVENTPUMP

1PUMP

2PUMP

3PUMP

4 ALL

IV - HISTORY

PAGE ↑ PAGE ↑ PRINT



IV - MAIN MENU


Refer to page 2-1

Refer to page 2-1

Refer to page 2-1

IV - SETUPPUMP

1PUMP

2PUMP

3PUMP

4 WEIGHT CHANGE CONFIG

IV - PUMP XXPRIMARY SELECT

FLUIDSELECT DRUG

SELECT CONC.

SELECT DILUENT DOSE CALCS

ALARMS

SECONDARY ON OFF

IV - CHANGE CONFIGURATION - SELECT PARAMETER TO EDIT

EDIT DRUG EDIT FLUID

IV - ENTER PATIENT WEIGHT FOR CALCULATIONS. WEIGHT = ___ lbs/kg

7 8 9

4 5 6

1 2 3

0 . CLEAR ENTER



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Disconnecting a Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Noting an Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Displaying Infusion History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
OverviewThe 90437A-01 Flexport System Interface enables information from Abbott Lifecare Models 4, 4P, or Micro pumps to be displayed on Spacelabs Healthcare monitors.

Configure the infusion pump as shown in Table 1. Consult the pump manual for additional configuration setup procedures.

Pump AddressesThe Spacelabs Healthcare monitor display identifies each IV pump by its address. The Abbott pump address is determined by the transition connector provided by Spacelabs Healthcare. The last two digits of the part number molded into the transition connector specify its address. Addresses range from 01 to 16.

Note:If you use multiple pumps, each pump must have a different address.

Table 1: Infusion Pump Configuration

BaudRate

Character Length

Parity Setting

Stop Bit

Transition Connector

Part Number

Minimum Software Revision

1200 8-bit none 1 131-0798-xx (15-pin) 650-0293-xx* 235

xx equals the desired address from 01 to 16.*Multi-pump adapter.



Connecting the Flexport System InterfaceTo connect the Flexport system interface to the pump(s), complete the steps in the following Quickstart.

Figure 2-1: Multiple pump configuration

The Spacelabs Healthcare monitor is now ready to display information from the IV pump(s). To control other interface functions, refer to the sections that follow.

To connect the Flexport system interface to the pump(s):

• Connect the SDLC cable to the 9-pin male connector on the Flexport system interface.• Plug one end of the modular cable into the modular jack on the Flexport system

interface.

Single pump (refer to Figure 1-3 on page 1-3):

• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the connector on the pump.

Multi-pump (refer to Figure 2-1 on page 2-4):

• Plug the other end of the modular cable into the jack labeled FLEXPORT on the multi-pump adapter.

• Plug another modular cable into one of the four IV PUMP jacks on the multi-pump adapter.

• Plug the other end of that modular cable into a transition connector.• Plug the transition connector into the connector on the pump.

SDLCcable

SDLCterminator

modularcables

IVSDLC connector

transition connector

9-pin connector

pump

IVpump

IVpump

IVpump

multi-pumpadapter

SpacelabsHealthcare

monitor

systemFlexport

interface



Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the pump(s).

Figure 2-2: Bedside, remote, or central monitor, full screen

Figure 2-3: Central monitor, split screen

� Pump address.

� Selected medication or fluid. (Until you set up the drug or fluid for each pump, this field displays * * * * * * * *.)

� Selected pump or infusion rate. Initially, this field displays the pump rate. The calculated medication rate is displayed once you have selected the concentration or dose. Units for displays are based on those selected.

� The volume of fluids and the dose delivered since the last time one of the following conditions occurred:

• The pump started a new dose.

• The pump rate was titrated.

• The pump changed from secondary to primary or from primary to secondary.

� IV parameter key.

� Latest status message (for example, PUMPING). The displayed infusion may be either the primary or the secondary. The secondary infusion is displayed when the pump is pumping secondary (SEC PUMPING) or concurrently (CONCURRENT). Refer to Status Messages on page 2-19.

� � � � � �

PUMP DRUG/FLUID RATE VOL. INFUSED PUMP STATUS12 DOPAMINE 10.0 mcg/kg/min 122.1 ml I

V12 PUMPING

14 HEPARIN 1000.0 u/hr 233.4 ml 14 STOPPED9 NOREPINEPHRINE 3.0 mcg/min 10.9 ml 9 PUMPING4 D5W 250.0 ml/hr 10.0 ml 4 INFSN DONE

� � � �

PUMP DRUG/FLUID STATUS24 DOPAMINE PUMPING I

V88 HEPARIN STOPPED92 NOREPINEPHRINE SEC PUMPING44 D5W INFSN DONE



Entering Setup InformationSetup information is necessary for the monitor to display the drug (or fluid) names and to compute the medication and calculated pump rates. You can control the following functions from the Setup menu:

• Turn alarms ON or OFF.

• Enter patient weight.

• Edit drug or fluid names.

• Set up primary and secondary infusion lines.

• Select the infusion fluid.

• Select the infusion drug.

Once you select the infusion drug, you can perform the following functions:

• Enter the infusion concentration.

• Select the diluent fluid.

• Enter the infusion dose.

Note:Setup information can be entered only at the bedside monitor.

Enabling AlarmsWhen you turn alarms OFF, infusion pump alarms will no longer trigger an alarm on the Spacelabs Healthcare monitor.

Alarm settings default to ON.

Note:Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the infusion pump(s).

To turn alarms ON or OFF:

• Touch IV.• Touch SETUP.• Select a PUMP key.• Touch ALARMS ON/OFF.



Selecting an Infusion LineYou cannot set up the secondary line until you complete the primary infusion setup.

Note:The Abbott Lifecare Model 4P is the only pump that accommodates piggyback or secondary infusions.

Selecting the Infusion FluidThere are two pages of Select Fluid screens. The first page displays the list of fluids automatically supplied by the Flexport system interface. The second page enables you to select from a list of up to eight fluids that you can enter into the Flexport system interface’s memory. Refer to Editing Drug or Fluid Names on page 2-14 for information on entering these names.

Figure 2-4: Select Fluid screen

To select an infusion line:

• Touch IV.• Touch SETUP.• Select a PUMP key.• Touch PRIMARY/SECONDARY.

PUMP 12 - SELECT FLUIDLR D5 LR D5 NS D5 1/2 NS

D5 1/2 NS 20 KCL D5 1/4 NS D5W D10 NS

D10 1/2 NS D10 1/4 NS D10W NS

1/2 NS 1/4 NS TPN LIPIDS

PAGE ↑ PAGE ↓ ENTER

To select an infusion fluid:

• Touch IV.• Touch SETUP.• Select a pump key.• Touch SELECT FLUID.• Select a fluid from the list (or touch PAGE ↓ and then select a fluid).• Touch ENTER.



Table 2 defines the fluid/concentration abbreviations that correspond to the fluids listed on the Select Fluid screen.

Table 2: Fluid Abbreviation

Abbreviation Description

LR Lactated ringers

D5 LR 5% dextrose with lactated ringers

D5 NS 5% dextrose with 0.9% saline

D5 1/2NS 5% dextrose with 0.45% saline

D5 1/2NS 20 KCL 5% dextrose with 0.45% saline and 20 mEq potassium chloride/liter


D5W 5% dextrose with water





NS 0.9% saline

1/2 NS 0.45% saline

1/4 NS 0.2% saline

TPN Total parenteral nutrition

LIPIDS Fat emulsion delivered as part of parenteral nutrition



Selecting a DrugThe Select Drug screen provides 16 default drug names. Refer to Editing Drug or Fluid Names on page 2-14 for information on editing the default drug names.

Figure 2-5: Select Drug screen

After selecting a drug, the monitor displays (in order) screens for the concentration and diluent.

Selecting the Drug ConcentrationThe drug concentration represents the amount of a drug dissolved in a volume of diluent. The Flexport system interface saves the last entered default concentration values and unit of measure associated with the selected drug.

Access to this display is automatic from the Select Drug screen.

To change a value after you have completed an initial drug/fluid entry, complete all the steps listed in the following Quickstart. Figure 2-6 illustrates the Concentration screen.

PUMP 12 - SELECT DRUGAMINOPHYLLINE AMRINONE BRETYLIUM DOBUTAMINE

DOPAMINE ESMOLOL HEPARIN ISOPROTERENOL

LIDOCAINE METARAMINOL NITROGLYCERIN NITROPRUSSIDE

NOREPHINEPHRINE PHENTOLAMINE PHENYLEPHRINE PROCAINAMIDE

ENTER

To select a drug:

• Touch IV.• Touch SETUP.• Select a pump key.• Touch SELECT DRUG.• Select a drug from the list.• Touch ENTER.



Figure 2-6: Concentration screen

Caution:• The validity of the drug concentration or dose values that you enter is NOT checked by the

system.

• Calculated drug rates are displayed to one significant decimal place. Rates less than 0.05 will appear as 0.0.

PUMP 12 - ENTER DRUG QTY, UNITS, AND VOLUME. CONCENTRATION = _______

7 8 9 mcg mg /50 ml /100 ml

4 5 6 g ml /250 ml /500 ml

1 2 3 units mEq /1 L /2 L

0 . CLEAR ENTER

To select a drug concentration:

• Touch IV.• Touch SETUP.• Select a pump key.• Touch SELECT CONC.• Enter the drug quantity.• Select the unit of measure.• Select the fluid volume.• Touch ENTER.



Selecting the DiluentTo select a drug for infusion, you must first choose a drug from the Select Drug page. The selected drug becomes active upon touching the ENTER key. The Flexport system interface provides 16 default drug names. Refer to Editing Drug or Fluid Names on page 2-14 for information on editing those default drug names.

Access to this display is automatic from the Concentration screen.

To change your selection after you have completed an initial diluent entry, complete all the steps listed in the following Quickstart.

When you touch ENTER to complete the diluent entry, the monitor displays the Setup menu.

Selecting the DoseThe dose represents the amount of drug to be infused over a specified time period. Use this display to enter the quantity, units of measurement, and time units.

If you have completed an initial drug/fluid entry and wish to change a value, complete all the steps listed in the Quickstart on page 2-12.

Note:If the interface displays an initial VOLUME INFUSED for the pump you intend to use, you must clear that value at the pump before you start an infusion. Otherwise, the Flexport system interface will appear to add the volume infused from the previous infusion to the current infusion (either primary or secondary).

To select a diluent:

• Touch IV.• Touch SETUP.• Select a pump key.• Touch SELECT DILUENT.• Choose a diluent from the list (or touch PAGE↓ and then select a diluent).• Touch ENTER.



Figure 2-7: Dose Calcs screen

As you enter the quantity, unit of measurement, and unit of time, the monitor screen displays the complete dose and the calculated pump rate. This calculated pump rate is based on the concentration and dose values you enter. To arrive at this value, the Flexport system interface performs the following calculation:

CALCULATED PUMP RATE = DOSE/CONCENTRATION

Note:The calculated pump rate is provided as information only. The Flexport system interface does not control the actual set pump rate.

When you touch ENTER to complete the dose entry, the interface saves your selection and the monitor displays the Setup menu.

PUMP 12 - ENTER DRUG QUANTITY, UNITS, AND TIME. DOSE = _______

7 8 9 mcg mg /min /hr

4 5 6 g ml CALCULATED PUMP RATE= xxxx.x ml/hr

1 2 3 units mEq

0 . CLEAR mcg/kg mg/kg ENTER

To select the drug dose:

• Touch IV.• Touch SETUP.• Select a pump key.• Touch DOSE CALCS.• Enter the dose quantity.• Enter unit of measurement.• Enter the time unit.• Touch ENTER.



Setting Patient WeightTouching the WEIGHT key displays a screen with a prompt containing the current weight of the patient (if you entered it previously using the Weight screen, a cardiac output module, or the monitor admit function). The Patient Weight screen uses the same units as the bedside monitor (kg or pounds).

Figure 2-8: Patient Weight screen

After you complete your editing and touch ENTER, the current weight will appear on the appropriate displays. You can enter up to six characters, including the decimal point. The valid weight range is from 1 to 250 kg (2 to 551 pounds). The interface saves the weight so you can use it in the Dose Calcs screen with the mcg/kg and mg/kg units of measurement.

IV - ENTER PATIENT WEIGHT FOR CALCULATIONS. WEIGHT = __ lbs/kg

7 8 9

4 5 6

1 2 3

0 . CLEAR ENTER

To enter patient weight:

• Touch IV.• Touch SETUP.• Touch WEIGHT.• Enter the patient weight.• Touch ENTER.



Editing Drug or Fluid NamesThe Change Configuration screen for drug names (refer to Figure 2-9) initially lists the 16 default drug names. You can change the name of any of these drugs.

The Change Configuration screen for fluid names initially shows a page of eight blank keys. You can select any of the eight keys for the fluid name.

Figure 2-9: Change Drug Configuration screen

After you select a drug or fluid key to relabel, touch CHANGE NAME. The monitor displays the Change Drug (or Fluid) Name screen (refer to Figure 2-10).

To edit a drug or fluid name:

• Touch IV.• Select SETUP.• Touch CHANGE CONFIG.• Select EDIT DRUG or EDIT FLUID.• Select the name you want to change.• Touch CHANGE NAME.• Use the alphanumeric keys to make necessary changes.• Touch ENTER.

IV - CHANGE CONFIGURATION - SELECT DRUG KEY TO RELABELAMINOPHYLLINE AMRINONE BRETYLIUM DOBUTAMINE




CHANGE NAME



Figure 2-10: Change Drug (or Fluid) Name screen

• Enter each character or number using the alphanumeric keys.

• Touch DEL to eliminate the character highlighted by the cursor.

• Move through the name, character by character, using the arrow keys.

• Touch CLEAR to eliminate the entire name and start over. The screen displays blank fields in place of the name.

• Touch ENTER to complete the edit and store the name in memory.

• Enter up to fifteen characters.

After you complete your editing and touch ENTER, the name will appear in the appropriate display for selecting drugs or fluids. The interface saves the name so you can recall it the next time you connect the Flexport system interface.

IV-CHANGE DRUG (or fluid) NAME= _________________________

0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J

K L M N O P Q R S T

U V W X Y Z / % .

DEL ← → CLEAR ENTER



Disconnecting a PumpWhen you touch DISCONNECT, the Flexport system interface discontinues the infusion record. If the pump is operating when you touch this key, the infusion record stops, a new record starts, and all pump setup information is cleared from the interface. If you touch DISCONNECT when the pump is not operating, the setup information stored by the Flexport system interface is cleared and the line of pump data is removed from the display.

Note:• Touching the DISCONNECT key does NOT turn OFF the infusion pump.

• A pump can be disconnected only at the bedside monitor.

Do not turn the power OFF at the pump while connected to the Flexport system interface. Disconnect the module cable from the pump first.

When you turn an infusion pump OFF at the pump itself, the pump status listed on the monitor changes to DISCONNECTED. At this point the interface completes the history for the current infusion (HISTORY shows the time that the infusion ended). If you turn the pump ON again, the interface continues to display the drug/fluid information entered previously.

Noting an EventThe EVENT key stores the time and pump status in memory. There is no immediate feedback when you touch this key. When you review the pump history, there is an entry labeled EVENT at the time you noted.

Events you may want to record include procedures such as changing IV lines or bags without turning the pump OFF.

Note:An event can be noted only at a bedside monitor.

To disconnect a pump:

• Touch IV.• Touch DISCONNECT.• Select a PUMP key.• Touch YES.

To note an event:

• Touch IV.• Touch EVENT.• Select a PUMP key.



Displaying Infusion HistoryInfusion history displays in a table format listing the last 40 infusion events for the patient on four pages (refer to Figure 2-11). This view-only table is available at the bedside monitor only. It is not available for remote viewing.

The data shown in the table does not automatically update while you are viewing it. To update the history data, re-enter the history table by touching PREVIOUS and then HISTORY.

Figure 2-11: Example of History table

The word ACTIVE appearing in the Ended column indicates that the pump is presently infusing the drug or fluid. The interface updates the log of active entries each minute.

The word EVENT appearing in the Ended column indicates the time at which the clinician touched the EVENT key to record a miscellaneous event into the pump history. Events that you might want to record include changing infusion lines or bags without turning the pump OFF.

To display infusion history:

• Touch IV.• Touch HISTORY.

DATE BEGAN ENDED PUMP DRUG/FLUID CONCENTRATION FLOW RATE

VOL. INFSD

02/20 10:30am 12:10pm 12 DOPAMINE 400mg/250ml 30.0 ml/hr 50.0 ml

02/20 12:15pm EVENT 12 DOPAMINE 400mg/250ml 20.0 ml/hr 3.5ml

02/20 12:50pm 05:00pm 12 HEPARIN 2000u/500ml 100.0 ml/hr 500.0 ml


02/21 12:30am 01:00am 12 NOREPINEPHRINE 1mg/250ml 125.0 ml/hr 62.5 ml

02/21 01:30am ACTIVE 12 NOREPINEPHRINE 400mg/250ml 30.0 ml/hr 210.0 ml

02/21 01:30am 03:00am 14 HEPARIN 2000u/500ml 100.0 ml/hr 750.0 ml

02/21 03:30am 07:00am 13 D5W 100.0 ml/hr 350.0 ml

02/21 07:30am ACTIVE 14 D10 1/2NS 100.0 ml/hr 100.0 ml

02/21 08:00am ACTIVE 9 DOPAMINE 400mg/250ml 30.0 ml/hr 15.0 ml



Printing the Current DisplayTouch the PRINT key to print the information shown on the current display or infusion history table. Each recording is identified by the bed name, patient name, time, and date.

Note:The patient name you enter in the Spacelabs Healthcare monitor is the name that appears on the printout.

To print the infusion information:

• Touch IV.• Touch PRINT.

-OR-• Touch HISTORY.• Touch PRINT.



Status MessagesThe message DISCONNECTED indicates a problem with the pump or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the pump is powered ON.

• Verify that all cables are secure.

Table 3 lists the status messages that the Flexport system interface reports for the pump during Flexport system interface operation.

Note:Not all messages will appear for each pump. Refer to the manual for your specific pump to determine which messages are used.

Table 3: Status Messages

Message Text Indication

DISCONNECTED Pump has been disconnected or turned OFF.

HIGH FLOW Pump has detected high flow condition.

INFSN. DONE Primary infusion is complete.

KVO Pump pumping at KVO rate.

LOW BATTERY Battery requires recharging.

LOW FLOW Pump has detected low flow condition.

NO SENSOR Flow detector is not connected and dose function is disabled.

OCCLUSION Closed clamp, kinked or occluded tubing, or occluded filter detected.

OK Appears at pump sign ON.

PUMPING Pump is pumping normally.

PUMP ALARM Pump has detected an alarm condition.

SEC PUMPING Pump is operating the secondary line.

STOPPED Pump is stopped but not turned OFF.


Alaris IVAC 560/570/599

Directory of Keys

IV

IV - MAIN MENU


IV - DISCONNNECT MENUPUMP

1PUMP

2PUMP

3PUMP

4 ALL

IV - DISCONNNECT PUMP XX?YES NO

IV - EVENT MENUPUMP

1PUMP

2PUMP

3PUMP

4 ALL

IV - SETUP MENUPUMP

1PUMP

2PUMP

3PUMP


IV - PUMP XX MENUPRIMARY SELECT

FLUIDSELECT DRUG

SELECT CONC.

SELECT DILUENT

DOSE CALCS

ALARMS

SECONDARY ON OFF

IV - HISTORY MENU IV - CHANGE CONFIGURATION - SELECT PARAMETER TO EDIT

PAGE ↑ PAGE ↓ PRINT EDIT DRUG

EDIT FLUID


7 8 9

4 5 6

1 2 3

0 . CLEAR ENTER



Contents
OverviewThe 90437A-03 Flexport system interface enables information from an Alaris IVAC 560, 570, or 599 infusion pump to be displayed on Spacelabs Healthcare monitors.


Pump AddressesThe Spacelabs Healthcare monitor display identifies each IV pump by its address. This address is set at the pump. The addresses range from 01 to 16.


The multi-pump adapter enables you to connect up to four pumps to a single Flexport system interface.


Infusion Pump Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number


Alaris IVAC 560/570 with CIM II 1200 7 bit odd 1

131-0688-xx(9 pin)

Model 560 rev 0.19Model 570 rev 0.09

Alaris IVAC 599 with DCM 1200 8 bit forced 0 1

131-0686-xx(9 pin)

rev 10.0



Connecting the Flexport System InterfaceTo connect the Flexport system interface to the pump(s), complete the steps listed in the following Quickstart.

To connect the Flexport system interface:

• Connect the SDLC cable to the 9-pin male connector on the Flexport system interface.

• Plug one end of the modular cable into the modular jack on the Flexport system interface.

Single pump (refer to Figure 1-3 on page 1-3):• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the connector on the pumpMulti-pump (refer to Figure 3-1 on page 3-5):• Plug the other end of the modular cable into the jack labeled FLEXPORT on the

multi-pump adaptor.• Plug another modular cable into one of the four IV PUMP jacks on the multi-pump

adapter.• Plug the other end of that modular cable into a transition connector.• Plug the transition connector into the connector on the pump.• Repeat steps step 2 through step 4 for each pump.





SDLCcable

SDLCterminator

transitionconnector

modularcables

IVpump

IVpump

IVpump

IVpump

multi-pumpadapter

SpacelabsHealthcare

monitor

systemFlexport

interface






� Pump address.

� Selected medication or fluid. (Until you set up the drug or fluid for each pump, this field displays * * * * * * * *).


� The display of the volume of fluids infused varies depending on the pump model and the infusion mode:

• Alaris IVAC 560, 570 Primary and Secondary, and 599 Primary mode: Displays the volume of fluids infused since the last time you zeroed the “total volume infused” on the pump.

• Alaris IVAC 599 Secondary mode: Displays the volume of fluids infused since the secondary infusion was started. If the pump’s “total volume infused” is zeroed during a secondary infusion, the display will continue to accumulate. (This is distinguished from the PRIMARY mode in which the display starts from zero again if the “total volume infused” was zeroed.)



� � � � � �


V12 PUMPING

14 HEPARIN 1000.0 u/hr 233.4 ml 14 STOPPED9 NOREPINEPHRINE 3.0 mcg/min 10.9 ml 9 SEC PUMPING4 D5W 250.0 ml/hr 10.0 ml 4 INFSN DONE

� � � �





Entering Setup InformationSetup information is necessary for the monitor to display the drug (or fluid) names and to compute the medication and calculated pump rates. The SETUP key controls the following functions and effects only the monitor at which these adjustments are made:







Once you select the infusion drug, you may perform the following functions:




Enabling Alarms When you turn alarms OFF, infusion pump alarms will no longer trigger an alarm on the Spacelabs Healthcare monitor.

The alarm setting defaults to ON.

Note:Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the infusion pump.

To turn alarms ON/OFF from the Spacelabs Healthcare monitor:

• Touch IV.• Touch SETUP.• Select a pump key.• Touch ALARMS ON/OFF.



Selecting an Infusion LineYou cannot set up the secondary line until you complete the primary infusion setup. The Alaris IVAC model 570 and 599 pump’s controlled release infusion system (CRIS) mode is considered a modified SECONDARY mode. The drug that is infused using the CRIS mode adapter is entered into the Flexport’s SECONDARY setup.

Note:The model 560 pump does not support secondary infusion.



• Touch IV.• Touch SETUP.• Select a pump key.• Touch PRIMARY/ SECONDARY.


• Touch IV.• Touch SETUP.• Select a PUMP key.• Touch SELECT FLUID.

-OR-• Touch PAGE ↓ and then select a fluid.• Touch ENTER.






D5 1/2 NS 20 KCL D5 1/4 NS D5W D10 NS

D10 1/2 NS D10 1/4 NS D10W NS



Table 2: Fluid Abbreviations


LR lactated ringers




D5 1/2NS 20KCL 5% dextrose with 0.45% saline and 20 mEq Potassium Chloride/Liter






D10 W 10% dextrose with water

NS 0.9% saline

1/2 NS 0.45% saline

1/4 NS 0.2% saline





Selecting a DrugTo select a drug for infusion, you must first choose a drug from the Select Drug page. The selected drug becomes active upon touching the ENTER key. The Flexport system interface provides 16 default drug names. Refer to Editing Drug or Fluid Names on page 3-15 for information on editing those default drug names.


After selecting a drug, the monitor displays (in order) the concentration and diluent.

Selecting the Drug ConcentrationThe drug concentration represents the amount of a drug dissolved in a volume of diluent. The Flexport system interface saves the last entered default concentration values and unit of measure associated with the selected drug. (Refer to Figure 3-6.)

Access to this display is automatic from the Select Drug screen; continue to complete the steps from the fifth bullet in the following Quickstart.

To change a value after you have completed an initial drug/fluid entry, follow all of the steps listed in the following Quickstart.





ENTER

To select a drug:






system.


Selecting the DiluentA diluent is a fluid used to dilute a drug for infusion. The fluids you can choose as drug diluents are the same as those you can choose as infusion fluids. Refer to Selecting the Infusion Fluid on page 3-8 for details on selecting a diluent. The Flexport system interface saves the last entered diluent associated with a selected drug.


• Touch IV.• Touch SETUP.• Select a pump key.• Touch SELECT CONC.• Enter the drug quantity.• Select the unit of measure.• Select the volume of fluid.• Touch ENTER.


7 8 9 mcg mg /50 ml /100 ml

4 5 6 g ml /250 ml /500 ml


0 . CLEAR ENTER



Access to this display is automatic from the Concentration screen. Continue to complete the steps after -OR- in the following Quickstart.

To change your selection after you have completed an initial diluent entry, complete all of the steps listed in the following Quickstart.



If you have completed an initial drug/fluid entry and wish to change a value, complete all of the steps listed in the following Quickstart.

Note:If the Flexport system interface displays an initial VOLUME INFUSED for the pump you intend to use, you must clear that value at the pump before you start an infusion. Otherwise, the Flexport system interface will appear to add the volume infused from the previous infusion to the current infusion (either primary or secondary).


• Touch IV.• Touch SETUP.• Select a pump key.• Touch SELECT DILUENT.• Choose a diluent from the list.

-OR-• Touch PAGE ↓ and then select a diluent.• Touch ENTER.


• Touch IV.• Touch SETUP.• Select a pump key.• Touch DOSE CALCS.• Enter the dose quantity.• Enter the unit of measurement.• Enter the time unit.• Touch ENTER.











1 2 3 units mEq




Setting Patient WeightTouching the WEIGHT key displays a screen with a prompt that contains the current weight of the patient (if you entered it previously using the Weight screen, a cardiac output module, or the monitor admit function). The Patient Weight screen uses the same units as the bedside monitor (kg or pounds).


After you complete your editing and touch ENTER, the current weight will appear in the appropriate displays. You can enter up to six characters, including the decimal point. The valid weight range is from 1 to 250 kg (2 to 551 pounds). The Flexport system interface saves the weight so you can use it in the Dose Calcs screen with the mcg/kg and mg/kg units of measurement.


7 8 9

4 5 6

1 2 3

0 . CLEAR ENTER





Editing Drug or Fluid NamesThe Change Configuration screen for drug names initially lists the 16 default drug names. You can change the name of any of these drugs (refer to Figure 3-9).

The Change Configuration screen for fluid names initially displays eight blank keys. You can select any of the eight keys for the fluid name.


After you select a drug or fluid key to relabel, touch CHANGE NAME. The monitor displays the Change Drug (or Fluid) Name screen (refer to Figure 3-10).

Note:Drug or fluid names can be edited only at the bedside monitor.







CHANGE NAME










After you complete your editing and touch ENTER, the name appears in the appropriate display for selecting drugs or fluids. The interface saves the name so you can recall it the next time you connect the Flexport system interface.


0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J

K L M N O P Q R S T

U V W X Y Z / % .








Noting an EventThe EVENT key enables the interface to store time and pump status in memory. There is no immediate feedback when you touch this key. When you review the pump history, there is an entry labeled Event at the time you noted.




• Touch IV.• Touch DISCONNECT.• Select a pump key.• Touch YES.

To note an event:

• Touch IV.• Touch EVENT.• Select a pump key.



Displaying Infusion HistoryInfusion history displays in a table format listing the last 40 infusion events for the patient on four pages (refer to Figure 3-11). This view-only table is available at the bedside monitor only and is not available for remote viewing.







DATE BEGAN ENDED PUMP DRUG/FLUID CONCENTRATION FLOW RATE VOL. INFSD


02/20 12:15pm EVENT 12 DOPAMINE 400mg/250ml 20.0 ml/hr 3.5 ml






02/21 03:30am 07:00am 13 D5W 100.0 ml/hr 350.0 ml















Note:On the Alaris IVAC model 599 infusion pump, all serial communications are suspended while the pump rate is being adjusted at the pump. If the pump rate adjustment occurs continuously over an extended time (greater than 20 seconds), the Flexport will consider the communications to be interrupted and display a DISCONNECTED message.




AIR IN LINE Pump has detected air in IV tubing.

CRIS MODE Pump is operating in CRIS MODE.


DOOR OPEN Pump has detected an open door.

FLOW SENSOR Pump has detected a problem with the flow sensor.




LOW FLOW Low flow condition detected.

OCCLUSION Tubing occlusion detected.







Alaris 980C/PC-1/PC-2/PC-4

Directory of Keys

IV

IV - MAIN MENU


Refer to page 4-2


1PUMP

2PUMP

3PUMP

4 ALL

IV - DISCONNNECT PUMP 1?YES NO

IV - EVENTPUMP

1PUMP

2PUMP

3PUMP

4 ALL

IV - HISTORY

PAGE ↑ PAGE ↓ PRINT



IV

IV - MAIN MENU


Refer to page 4-1

Refer to page 4-1

Refer to page 4-1

IV - SETUPPUMP

1PUMP

2PUMP

3PUMP


IV - CHANGE CONFIGURATION - SELECT PARAMETER TO EDITEDIT

DRUGEDIT

FLUID


7 8 9

4 5 6

1 2 3

0 . CLEAR ENTER


FLUIDSELECT DRUG

SELECT CONC.

SELECT DILUENT

DOSE CALCS

ALARMS

SECONDARY ON OFF



Contents
OverviewThe 90437A-02 Flexport system interface enables information from the Alaris Medical Systems 980C, PC-1, PC-2, or PC-4 infusion pump to be displayed on Spacelabs Healthcare monitors.


Pump AddressesThe Spacelabs Healthcare monitor display identifies each IV pump by its address is set at the pump and ranges from 01 to 16. Alaris refers to the pump address as the serial number. Refer to the manufacturer’s manual for instructions on setting pump addresses.


The multi-pump adapter enables you to connect up to four pumps to a single Flexport system interface. The dual-line pump (Gemini PC-2) is considered two pumps that can be connected to one of the following:

• Four single-line pumps (for example, 980C or Gemini PC-1)

• Two dual-line pumps (for example, Gemini PC-2)

• One dual-line pump and up to two single-line pumps

• One quadruple-line pump for Gemini PC-4

Table 1: Pump Configuration

Baud Rate

Character Length

Parity Setting Stop Bit

1200 8 bit none 1



Connecting the Flexport System InterfaceTo connect the Flexport system interface to multiple pumps, complete the steps listed in the following Quickstart.



interface.

Single pump (refer to Figure 1-3 on page 1-3):

• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the connector on the pump.

Multi-pump (refer to Figure 4-1 on page 4-5):

• Plug the other end of the modular cable into the jack labeled FLEXPORT on the multi-pump adaptor.

• Plug another modular cable into one of the four IV PUMP jacks on the multi-pump adapter.

• Plug the other end of that modular cable into a transition connector.• Plug the transition connector into the connector on the pump.





cable

SDLCterminator

transitionconnector

modularcables

IVpump

IVpump

IVpump

IVpump

multi-pumpadapter

SpacelabsHealthcare

monitor

systemFlexport

interface






Pump address� Selected medication or fluid. (Until you set up the drug or fluid for each pump, this field

displays * * * * * * * *.)








� � � � � �


V12 PUMPING


� � � �





Entering Setup InformationSetup information is necessary for the Spacelabs Healthcare monitor to display the drug (or fluid) names and to compute the medication and calculated pump rates. The SETUP key controls the following functions and affects only the monitor at which these adjustments are made:
























• Touch IV.• Touch SETUP.• Select a pump key.• Touch PRIMARY/SECONDARY.

PUMP 12 - SELECT FLUID

LR D5 LR D5 NS D5 1/2 NS

D5 1/2 NS 20 KCL D5 1/4 NS D5W D10 NS

D10 1/2 NS D10 1/4 NS D10W NS







LR lactated ringers


D5 NS 5% dextrose with 0.9% normal saline

D5 1/2NS 5% dextrose with 0.45% normal saline

D5 1/2NS 20KCL 5% dextrose with 0.45% normal saline and 20 mEq potassium chloride/liter



D10 NS 10% dextrose with 0.9% normal saline




NS 0.9% normal saline

1/2 NS 0.45% normal saline

1/4 NS 0.2% normal saline

TPN total parenteral nutrition

LIPIDS fat emulsion delivered as part of parenteral nutrition





Selecting a DrugThe Select Drug screen provides 16 default drug names. Refer to Editing Drug or Fluid Names on page 4-15 for information on editing the default drug names.


After selecting a drug, the monitor displays (in order) screens for the concentration and diluent.

Selecting the Drug ConcentrationThe drug concentration represents the amount of a drug dissolved in a volume of diluent. The Flexport system interface saves the last entered default concentration values and unit of measurement associated with the selected drug.


To change a value after you have completed an initial drug/fluid entry, complete the steps listed in the following Quickstart. Figure 4-6 illustrates the Concentration screen.





ENTER

To select a drug:

• Touch IV.• Touch SETUP.• Touch a pump key.• Touch SELECT DRUG.• Select a drug from the list.• Touch ENTER.





system.



• Touch IV.• Touch SETUP.• Touch a pump key.• Touch SELECT CONC.• Enter the drug quantity.• Select the unit of measurement.• Select the volume of fluid.• Touch ENTER.


7 8 9 mcg mg /50 ml /100 ml

4 5 6 g ml /250 ml /500 ml


0 . CLEAR ENTER








If you have completed an initial drug/fluid entry and wish to change a value, complete all the steps listed in the following Quickstart.



• Touch IV.• Touch SETUP.• Select a pump key.• Touch SELECT DILUENT.• Select a diluent from the list (or touch PAGE ↓ and then select a diluent).• Touch ENTER.






As you enter the quantity, unit of measurement, and unit of time, the monitor displays the complete dose and the calculated pump rate. This calculated pump rate is based on the concentration and dose values you enter. To arrive at this value, the Flexport system interface performs the following calculation:




PUMP A - ENTER DRUG QUANTITY, UNITS, AND TIME. DOSE = _______



1 2 3 units mEq






After you complete your editing and touch ENTER, the current weight will appear in the appropriate screens. You can enter up to six characters, including the decimal point. The valid weight range is from 1 to 250 kg (2 to 551 pounds). The interface saves the weight so you can use it in the Dose Calcs screen with the mcg/kg and mg/kg units of measurement.


7 8 9

4 5 6

1 2 3

0 . CLEAR ENTER





Editing Drug or Fluid NamesThe Change Configuration screen for drug names initially lists the 16 default drug names. You can change the name of any of these drugs.

The Change Configuration screen for fluid names initially displays eight blank keys. You can select any of the eight keys for the fluid name. Figure 4-9 shows the Change Drug Configuration display.

Figure 4-9: Change Drug Configuration display

After selecting a drug or fluid key to relabel, touch CHANGE NAME. The monitor displays the Change Drug (or Fluid) Name screen (refer to Figure 4-10).


• Touch IV.• Touch SETUP.• Touch CHANGE CONFIG.• Touch EDIT DRUG or EDIT FLUID.• Select the name you wish to change.• Touch CHANGE NAME.• Use alphanumeric keys to make necessary changes.• Touch ENTER.





CHANGE NAME












0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J

K L M N O P Q R S T

U V W X Y Z / % .







Do not turn the power OFF on the pump while connected to the Flexport system interface. Disconnect the module cable from the pump first.







To note an event:




Displaying Infusion HistoryInfusion history displays as a table listing the last 40 infusion events for the patient on four pages (refer to Figure 4-11). This view-only table is available at the bedside monitor only and is not available for remote viewing.








VOL. INFSD


02/20 12:15pm EVENT 12 DOPAMINE 400mg/250ml 20.0 ml/hr 3.5 ml






02/21 03:30am 07:00am 13 D5W 100.0 ml/hr 350.0 ml


















AIR IN LINE Pump has detected air in IV tubing

DISCONNECTED Pump has been disconnected or turned OFF

DOOR OPEN Pump has detected an open door

INFSN. DONE Primary infusion is complete

KVO Pump pumping at KVO rate

LOW BATTERY Battery requires recharging

OCCLUSION Closed clamp, kinked or occluded tubing, or occluded filter detected

OK Pump is signing ON

PRIMARY MODE Pump is operating the primary line

PUMP ALARM Pump has detected an alarm condition

PUMPING Pump is pumping normally

SEC PUMPING Pump is operating the secondary line

STOPPED Pump is stopped but not turned OFF


Bard CritiCore

Directory of Keys

URINE

URINE - MENUALARM LIMITS SETUP VIEW

ALARMS PRINT

URINE - SETUPLARGE TXT

SMALL TXT

URINE - ALARM LIMITS

TEMP CNTNR FLOW

URINE - ALARM LIMITS - FlowFLOW HI =

XXXXLO=

XXXXON OFF

URINE - ALARM LIMITS - CntnrCNTNR HI =

XXXXON OFF

URINE - ALARM LIMITS - TempTEMP HI =

XXXXLO=

XXXXON OFF


Bard CritiCore

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OverviewThe 90442A Flexport system interface enables information from a Bard CritiCore monitor to be displayed on Spacelabs Healthcare monitors.

Configure the CritiCore monitor as shown in Table 1. Consult the Bard CritiCore manual for additional configuration setup procedures

* The Bard CritiCore monitor must contain the optional CritiCore communications module.

Table 1: Bard CritiCore Configuration

BaudRate


Installation Kit

Part Number

Modular Cable

Part Number

9600 N/A* 045-0036-xx 012-0510-xx


Bard CritiCore

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the CritiCore monitor, complete the steps in the following Quickstart.


Figure 5-2: CritiCore communications module side insert

To connect the Flexport System Interface:

• Connect the SDLC cable to the 9-pin male connector on the Flexport system interface as shown in Figure 5-1.

• Plug the communications module power supply into a wall outlet and into the side of the CritiCore monitor (refer to Figure 5-2).

• Under the remote switch panel on the back of the CritiCore monitor, set the communications format switch to the Flexport Protocol position.

• Turn on the CritiCore monitor and complete the setup procedure on the back panel.• Plug one end of a modular cable into the modular jack on the Flexport system interface.• Plug the other end of the modular cable into the 4-pin female mini-DIN jack on the

CritiCore communications module.

communicationsmodulepower supply

SDLCcable

SDLCterminator

modularcable

Flexport

interfaceBard

CritiCore

SpacelabsHealthcare

monitor

system

indicator LED4-pin mini-DIN jack

power supply connector


Bard CritiCore

The Spacelabs Healthcare monitor is now ready to display information from the CritiCore monitor. The indicator LED on the CritiCore monitor’s side insert will pulse with each data burst. For further information on the indicator LED, refer to the appropriate CritiCore monitor documentation.

To control other interface functions, refer to the sections that follow.

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to the Flexport system interface, the monitor provides the following information from the CritiCore monitor.

Figure 5-3: Bedside monitor, large text screen

Figure 5-4: Bedside monitor, small text screen

� Present interval output value (ml)

� Flow Rate value (ml/hr)

� Minutes value from the CritiCore monitor time clock (min)

� URINE parameter key

� Bladder temperature value (°F or °C)

� Alarm status bell appears when Flexport alarms are turned ON. Flow, Cntnr, and Temp alarms must also be enabled at the CritiCore monitor.

� CritiCore monitor interval length value (minute or hour)

� � � � �

49 Prsnt 294 Flow 23 Time URINE

101.2 Temp

minml ml/hr F

27 1012 15Prior

ml

Cntnr

ml

Int

min

� �

� � �

URINE

Temp = 101.2 F

Prsnt = 49 ml

Prior

Time

=

=

27 ml

23 min

� �


Bard CritiCore

Container volume value (ml)

Prior interval output value (ml)

Note:The units for temperature (°F or °C) and interval length (minute or hour) are programmable via the CritiCore monitor. Refer to the appropriate CritiCore documentation for instructions. The communications link will be re-established after changing the units.

Enabling AlarmsThe Alarm Limits menu allows you to enable alarm limits for each parameter (FLOW, TEMP, and CNTNR). When an alarm is turned ON and that parameter value exceeds an alarm limit, all of the following occur:

• an alarm tone sounds,

• the URINE key flashes,

• the alarm limits key for that parameter flashes, and

• the alarm bell flashes.

Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the CritiCore

monitor.

• Alarm limits can only be adjusted at the CritiCore monitor. Alarm violation is detected at the CritiCore monitor, and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• Alarm tones on the CritiCore monitor can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.


• Touch URINE.• Touch ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


Bard CritiCore

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the CritiCore monitor’s parameters (refer to Figure 5-5). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays URINE ALM OFF to the right of the URINE key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.

Figure 5-5: View Alarms screen

Selecting a Display FormatTwo display formats are available for the bedside monitor (refer to Display Detail on page 5-5).

The default setting is LARGE TXT.

To view alarm settings:

• Touch URINE.• Touch VIEW ALARMS.

To select a display format:

• Touch URINE.• Touch SETUP.• Select LARGE TXT or SMALL TXT.

Temp 102.0 Flow 4500 URINE

101.2 Temp92.0 200

F

Cntnr 2000


Bard CritiCore

Printing the Current DisplayTouch the PRINT key to print the information shown on the current display. Each recording is identified by the bed name, patient name, time, and date.


To print the CritiCore display:

• Touch URINE.• Touch PRINT.


Bard CritiCore

Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the CritiCore or the cabling. If the Spacelabs Healthcare monitor displays this message, perform the following troubleshooting steps:

• Verify that the CritiCore monitor is powered ON.


Table 2 lists the status messages that the Flexport system interface reports for the CritiCore monitor during Flexport operation.


Message Text Indication Alarm Sounds

COMMUNICATION LINK LOST

The communication between the Flexport system interface and the CritiCore monitor is interrupted. Yes

CHECK MONITORThe CritiCore monitor is OFF, or the CritiCore communications module is not receiving data internally from the CritiCore monitor.

No

CHECK “SET VALUE” SWITCH

The Set Value switch on the back of the CritiCore monitor was not returned to the normal operation position. No

FULL CONTAINER The Bard CritiCore collection container is full. No

NO CONTAINER No container is in place, or the collection container is not seated properly within the CritiCore monitor. No

MONITOR NOT LEVEL The CritiCore monitor is not level (volume measurements cannot be taken under this condition). No

CHECK TEMPERATURE PROBE

A valid temperature cannot be detected, or no temperature probe is connected to the CritiCore monitor. No



Baxter-Edwards Explorer

Directory of Keys

CO

CO - MAIN MENUALARM LIMITS SETUP VIEW

ALARMS PRINT

These keys appear on the bedside monitor only.

LARGE TXT

SMALL TXT

CO - ALARM LIMITS

SPO2 SVO2

CO - ALARM LIMITS - SVO2SVO2 HI =

XXXXLO=

XXXXSPO2

ON OFF SVO2

CO - ALARM LIMITS - SPO2SPO2 HI =

XXXXLO=

XXXXSPO2

ON OFF SVO2


Contents
OverviewThe 90442A Flexport system interface allows information from a Baxter-Edwards Critical Care Division Explorer cardiac output (CO) monitor to be displayed on a Spacelabs Healthcare monitor.

Configure the CO monitor as shown in Table 1. Consult the manufacturer’s manual for additional configuration setup procedures.

Table 1: CO Monitor Configuration

Baud Rate


Baxter Interface Module

Installation Kit Part Number


Part Number

9600 06.37 60-RS-SL 045-0010-xx 131-0686-xx



Connecting the Flexport System InterfaceTo connect the Flexport system interface to the CO monitor, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the CO monitor. To control other interface functions, refer to the sections that follow.

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the CO monitor.

Figure 6-1: Bedside monitor, large text


• Connect the SDLC cable to the 9-pin male connector on the Flexport system interface as shown in Figure 1-3 on page 1-3.


• Plug the other end of the modular cable into the transition connector.• Connect the 60-RS-SL interface (Baxter provides the interface) module to the

CO monitor.• Plug the transition connector into the 9-pin connector on the 60-RS-SL interface

module.

� � � � �

9.8 CO 398 EDV 163 SV

CO

96 SpO2

%l/min ml ml

--.- Cl 235 ESV 41 REF 77 SvO2

%ml %

� � �



Figure 6-2: Bedside monitor, small-text screen


� Cardiac output average value

� End-diastolic volume average value

� Stroke volume average value

� CO parameter key

� Pulse oximeter SpO2 value

� Alarm status bell (appears when alarms are turned ON)

� Venous oximeter SvO2 value

Ejection fraction average value

End-systolic volume average value

� Cardiac index average value

� Patient/room ID

Note:Monitors can display either cardiac output or cardiac index, but not both at the same time.

� �

CO

SpO2= 96%�SvO2= 77%

CO= 9.8 l/minCl= --.-

� � �

� �

� SpO2= 96% EDV=398ml

CO

� SvO2= 77% ESV=235ml

� CO= 9.8 l/min SV=163ml �� Cl=--.- REF= 41%

ICU 14�

�



Enabling AlarmsThe Alarm Limits menu allows you to enable alarm limits for SpO2 or SvO2. When an alarm is turned ON and that parameter value exceeds an alarm limit, all of the following occur:


• the CO key flashes,



When both parameter alarms are turned OFF, alarm status messages will still cause the CO key to flash.


Note:• Turning Flexport system interface alarms ON or OFF does not affect alarms on the CO monitor.

• Alarm limits can only be adjusted at the CO monitor. Alarm violation is detected at the monitor, and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• Alarm tones on the CO monitor can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.

To turn alarms ON or OFF from the Spacelabs Healthcare monitor:

• Touch CO.• Touch ALARM LIMITS.• Select SPO2 or SVO2.• Touch the parameter alarm ON/OFF key.



Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the CO monitor’s parameters (refer to Figure 6-4). If alarms for SpO2 and SvO2 parameters are turned OFF, the Spacelabs Healthcare monitor displays CO ALM OFF to the right of the CO key. If alarms are turned ON for any parameter, a bell is displayed instead. The alarm bell flashes when an alarm limit is violated.




To view alarms settings:

• Touch CO.• Touch VIEW ALARMS.


• Touch CO.• Touch SETUP.• Select LARGE TXT or SMALL TXT.

SpO2SvO2

100908040 C

O96 SpO2

%

80 SvO2

%





Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the CO monitor or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the CO monitor is powered ON.


Table 2 lists the status messages that the Flexport system interface reports for the CO monitor during Flexport system interface operation.

To print the CO monitor display:

• Touch CO.• Touch PRINT.




Communication between the CO monitor and the Spacelabs Healthcare monitor has been interrupted. Yes

EXPLORER DISCONNECTED

Communication problem has been detected between the CO monitor and 60-RS-SL. No

SVO2 PROBLEM — CHECK EXPLORER

The SvO2 catheter is not attached, not calibrated, or is defective. No

SPO2 PROBLEM — CHECK EXPLORER The SpO2 probe is not attached or is defective. No

CO/REF PROBLEM — CHECK EXPLORER

The cardiac output catheter is not connected or is not configured properly. No


Baxter Flo-Gard 6201/6301

Directory of Keys

IV

IV - MAIN MENU



APUMP

B ALL

IV - EVENT IV - DISCONNNECT PUMP XX?PUMP

APUMP

B ALL YES NO

IV - SETUPPUMP

APUMP

B WEIGHT CHANGE CONFIG


FLUIDSELECT DRUG

SELECT CONC.

SELECT DILUENT

DOSE CALCS

ALARMS

SECONDARY ON OFF



IV - HISTORY

PAGE ↑ PAGE ↓ PRINT


7 8 9

4 5 6

1 2 3

0 . CLEAR ENTER



Contents
OverviewThe 90437A-06 Flexport system interface enables information from Baxter Flo-Gard 6201 and 6301 volumetric infusion pumps to be displayed on Spacelabs Healthcare monitors.



Baud Rate

Character Length


9600 8-bit none 1



Connecting the Flexport System InterfaceTo connect the Flexport system interface to the IV pump(s), complete the steps listed in the following Quickstart.







interface.• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the connector on the infusion pump “communications

port.”

� � � � � �

PUMP DRUG/FLUID RATE VOL. INFUSED PUMP STATUSA DOPAMINE 10.0 mcg/kg/min 122.1 ml I

VA PUMPING

B HEPARIN 1000.0 u/hr 233.4 ml B STOPPED

� � � �

PUMP DRUG/FLUID STATUSA DOPAMINE PUMPING I

VB HEPARIN STOPPED



� Pump address.








� Latest status message (for example, PUMPING). The displayed infusion may be either the primary or the secondary. The secondary infusion is displayed when the pump is pumping secondary (SEC PUMPING). Refer to Status Messages on page 7-20.

Entering Setup InformationSetup information is necessary for the monitor to display the drug (or fluid) names and to compute the medication and calculated pump rates. The SETUP key controls the following functions and affects only the monitor at which these adjustments are made:















The alarm setting defaults to ON.

Note:Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the infusion pump(s).





• Touch IV.• Touch SETUP.• Select a pump key.• Touch PRIMARY/SECONDARY.







D5 1/2 NS 20 KCL D5 1/4 NS D5W D10 NS

D10 1/2 NS D10 1/4 NS D10W NS





LR Lactated ringers




D5 1/2NS 20 KCL 5% dextrose with 0.45% saline and 20 mEq potassium chloride/liter











After selecting a drug, the monitor displays (in order) displays for the concentration and diluent.

NS 0.9% saline

1/2 NS 0.45% saline

1/4 NS 0.2% saline









ENTER

Table 2: Fluid Abbreviations (continued)






To change a value after you have completed an initial drug/fluid entry, complete all the steps listed in the following Quickstart. Figure 7-5 illustrates the Concentration screen.

To select a drug:



• Touch IV.• Touch SETUP.• Select a pump key.• Touch SELECT CONC.• Enter the drug quantity.• Select the unit of measurement.• Select the fluid volume.• Touch ENTER.





system.



7 8 9 mcg mg /50 ml /100 ml

4 5 6 g ml /250 ml /500 ml


0 . CLEAR ENTER








If you have completed an initial drug/fluid entry and wish to change a value, complete all the steps listed in the following Quickstart.



• Touch IV.• Touch SETUP.• Select a pump key.• Touch SELECT DILUENT.• Choose a diluent from the list (or touch PAGE ↓ and then select a diluent).• Touch ENTER.













1 2 3 units mEq






After you complete your editing and touch ENTER, the current weight appears on the appropriate displays. Enter up to six characters, including the decimal point. The valid weight range is from 1 to 250 kg (2 to 551 pounds). The interface saves the weight so you can use it in the Dose Calcs screen with the mcg/kg and mg/kg units of measurement.


7 8 9

4 5 6

1 2 3

0 . CLEAR ENTER








After you select a drug or fluid key to relabel and touch CHANGE NAME, the monitor displays the Change Drug (or Fluid) Name screen (refer to Figure 7-9).





CHANGE NAME










After you complete your editing and touch ENTER, the name will appear in the appropriate display for selecting drugs or fluids. The interface saves the name enabling you to recall it the next time you connect the Flexport system interface.


0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J

K L M N O P Q R S T

U V W X Y Z / % .







Do not turn the power OFF at the pump while connected to the Flexport system interface. Disconnect the module cable from the pump first.








Noting an EventWhen you note an event, the interface stores the time and pump status in memory. There is no immediate feedback when you touch this key. When you review the pump history, there is an entry labeled EVENT at the time you noted.



To note an event:




Displaying Infusion HistoryInfusion history displays as a table listing the last 40 infusion events for the patient on four pages (refer to Figure 7-10). This view-only table is available at the bedside monitor only and is not available for remote viewing.






VOL. INFSD








02/21 03:30am 07:00am 13 D5W 100.0 ml/hr 350.0 ml


























OCCLUSION Closed clamp, kinked or occluded tubing, or occluded filter detected.








Bear 1000

Directory of Keys

VENT

VENT - MAIN MENU

ALARM LIMITS SETUP

FREEZE LARGE TXT VIEW MODE

VIEW STATUS

VIEW ALARMS PRINT

ON OFF SMALL TXT

VENT - SETUPWAVE SIZE

↑SIZE

↓SWEEP SPEED

WAVE TYPE

ON OFF PRS FLOW

25 mm/sec

12.5 mm/sec

6.25 mm/sec

3.12 mm/sec

1.56 mm/sec

VENT - ALARM LIMITS

PIP Vmin RR

VENT - ALARM LIMITS - RRRR HI =

XXXLO=XXX

RR

ON OFF PIP

VENT - ALARM LIMITS - VminVmin HI =

XXXLO=XXX

Vmin

ON OFF RR

VENT - ALARM LIMITS - PIPPIP HI =

XXXXLO=XXX

PIP

ON OFF Vmin

Bear 1000

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Viewing Ventilator Mode History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
OverviewThe 90436A-12 Flexport system interface enables information from a Bear 1000 ventilator to be displayed on Spacelabs Healthcare monitors.

Configure the ventilator as shown in Table 1. Consult the ventilator manual for additional configuration setup procedures.

Table 1: Ventilator Configuration

Baud Rate

Character Length

Parity Setting Stop Bit Minimum Software

Revision

19,200 8-bit none 1 9.7 or A.3


Bear 1000

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the ventilator, complete the steps listed in the following Quickstart.

Figure 8-1: Flexport system interface configuration without graphical display unit


• Connect the SDLC cable to the 9-pin male connector on the Flexport system interface as shown in Figure 8-1 and Figure 8-2.

• If no graphical display is connected to the ventilator, connect the transition connector (P/N 131-0686-xx) to the ventilator’s 9-pin connector labeled RS-232 INTERFACE (refer to Figure 8-1).If a graphical display is connected to the ventilator, connect the transition connector (P/N 131-1039-xx) to the graphical display unit connector labeled DIGITAL OUT (refer to Figure 8-2).

• Connect the 15-pin connector on the modular cable into the 15-pin connector on the ventilator labeled ANALOG OUTPUT and the 6-pin connector into the transition connector.

• Plug the other end of the modular cable into the 8-pin receptacle on the Flexport system interface.

SDLCcable SDLC

terminator

modularcable analog output

transition

RS-232 interface

connector ventilator

SpacelabsHealthcare

monitor

systemFlexport

interface


Bear 1000

Figure 8-2: Flexport system interface configuration with graphical display unit

The Spacelabs Healthcare monitor is now ready to display information from the ventilator. To control other interface functions, refer to the sections that follow.

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the ventilator.

Figure 8-3: Bedside monitor, large-text screen


SDLCcable SDLC

terminator

modularcable

ventilator

transitionconnector

graphicaldisplay unit

analogoutput

digital out

SpacelabsHealthcare

monitor

systemFlexport

interface

� � � � � �

21 PIP 6 PLT 22 FiO2 VENT

1.22 Vt WAVE=PRESScmH2O % L

cmH2O Vmin RR

1.8 I:E 8 MAP 14.6 12cmH2O L BPM

� � �

� � �

VENT

Vt = 1.22L WAVE=PRESSRR =12BPM

PIP = 21cmH2O

FiO2 = 22%

� � �


Bear 1000


� Peak inspiratory pressure

� Plateau pressure

� Fractional inspired O2 control setting

� VENT parameter key

� Tidal volume

� Waveform identification label


Respiratory rate

Minute volume

� Mean airway pressure

� Ratio of inspiration time to expiration time (I:E ratio is typically expressed as 1:X.X, where X.X is the value displayed and equals E/I) *

* The displayed I:E ratio may differ slightly from the value shown on the Bear 1000. The Bear 1000 does not send the displayed data as it does for other parameters. Instead, it sends a value requiring calculations that may result in a variance as shown in Table 2.

Table 2: Display Variance

I:E Ratio Range Maximum Possible Variance

0.25 to 1.2 0

1.3 to 4.6 ±0.1

4.7 to 6.5 ±0.2

6.6 to 8.2 ±0.3

>8.3 is not displayed

� � �

VENT

� Vt=1.22L PIP=21cmH2O

Vmin=14.6L MAP=8cmH2O

RR=12BPM PLT=6cmH2O

� FiO2=22% I:E=1.8

� � �


Bear 1000

Enabling AlarmsThe Alarm Limits menu allows you to enable alarm limits for each parameter. When an alarm is turned ON and that parameter value exceeds an alarm limit, all of the following occur:


• the VENT key flashes,



When all parameter alarms are turned OFF, status alarms will still cause the VENT key to flash.

Alarm settings default to OFF.

Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the ventilator.

• Alarm limits can only be adjusted at the ventilator. Alarm violation is detected at the ventilator and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• Vmin alarm limits are displayed as question marks when insufficient data is provided by the ventilator. The ventilator determines when the limits have been exceeded and the Flexport will report the alarm condition.

• The ventilator provides a feature that prevents a high PIP alarm. With this feature, the ventilator will alarm, but will immediately force the PIP value to an acceptable range. The Flexport will display the generated alarm as well as the current, adjusted value of the PIP as shown on the ventilator.


• Touch VENT.• Touch ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


Bear 1000

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the ventilator’s parameters (refer to Figure 8-6). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays VENT ALM OFF to the right of the VENT key. If alarms are turned ON for any parameter, a bell is displayed instead. The alarm bell flashes when an alarm limit is violated. If an individual alarm is OFF, no limit values are displayed next to the parameter label.



• Touch VENT.• Touch VIEW ALARMS.

PIP 21 RR 27VENT

1.22 VT WAVE=PRESS0 3 L

12 RR ??.? BPM

Vmin ??.?


Bear 1000

Viewing Ventilator Mode HistoryChronological history of the last eight ventilator mode settings is displayed in the waveform zone, with the most recent value at the top of the left column and the oldest value at the bottom of the right column. Possible modes include ASSIST, SIMV/CPAP, and PRESSURE.

Figure 8-7: View Mode History screen

Viewing StatusThe VIEW STATUS key enables you to display the recent status messages sent by the ventilator. A maximum of four messages can be displayed on the bedside monitor, and three on the remote monitor (refer to Status Messages on page 8-13).

To view ventilator mode:

• Touch VENT.• Touch VIEW MODE.

To view ventilator status:

• Touch VENT.• Touch VIEW STATUS.

17:10 ASSIST 11:15 ASSIST VENT

1.22VT WAVE=PRESS15:47 SIMV/CPAP 9:31 PRESSURE L

14:23 PRESSURE 7:02 SIMV/CPAP 12RR

12:49 SIMV/CPAP 4:56 ASSIST BPM


Bear 1000

Entering Setup InformationChanging setup information is helpful in optimizing the monitor display. The SETUP key controls the functions described below and affects only the monitor at which these adjustments are made.

Turning Waveforms ON or OFFYou can turn waveforms OFF and display only the numeric values. When waveforms are OFF, the SWEEP SPEED key, the FREEZE ON/OFF keys, and the SIZE ↑ and SIZE ↓ keys are disabled.

The default setting is WAVE ON.

Adjusting the Waveform SizeIf the waveform is too large to fit within the display zone, use the waveform size keys to adjust the display size.

Note:The WAVE ON/OFF key must be set to ON for the size keys to appear and function.

To turn the waveform display ON or OFF:

• Touch VENT.• Touch SETUP.• Touch WAVE ON/OFF.

To adjust waveform size:

• Touch VENT.• Touch SETUP.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.


Bear 1000

Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 1.56, 3.12, 6.25, 12.5, and 25 mm/second.

The default setting is 12.5 mm/second.

Selecting a Waveform TypeYou can select either pressure or flow waveforms for display. Select PRS to display the pressure waveform, or select FLO to display the flow waveform. The two waveform displays are mutually exclusive.

Freezing the Waveform on the DisplayThe FREEZE ON key enables you to freeze the waveform on the display. When you freeze the waveform, the Flexport system interface continues to process, update, and display numeric information.

The default setting is FREEZE OFF.

To select a sweep speed:

• Touch VENT.• Touch SETUP.• Select SWEEP SPEED.• Select the desired speed.

To select a waveform type:

• Touch VENT.• Touch SETUP.• Touch WAVE TYPE.• Select PRS or FLOW.

To freeze the waveform on the display:

• Touch VENT.• Touch FREEZE ON.


Bear 1000




Note:• The patient name you enter in the Spacelabs Healthcare monitor is the name that appears on the

printout.

• The PRINT key does not print the waveform. A waveform recording is obtained by touching the monitor RECORD key.


• Touch VENT.• Select LARGE TXT or SMALL TXT.

To print the ventilator display:

• Touch VENT.• Touch PRINT.


Bear 1000

Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the ventilator or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the ventilator is powered ON.


• Verify that the ventilator’s baud rate is set at 19,200.

Table 3 lists the status messages that the Flexport system interface reports for the ventilator during Flexport system interface operation.




Communication between the ventilator and the monitor has been interrupted. Yes

GAS FAIL Gas supply (O2) pressure less than 27.5 psi. Yes

CYCLE FAIL Ventilator is not providing any mechanical breaths. Yes


Biochem International BCI 9000

Directory of KeysPO+ET

PO+ET - MAIN MENUALARM LIMITS SETUP

FREEZE SWITCH WAVES

VIEW ALARMS PRINT

ON OFFRefer to page 9-2

These keys are displayed only on the bedside monitor.

PO+ET - SETUP

SIZE SWEEP SPEED

LARGE TXTSMALL TXT

PO+ET - SETUP - SWEEP SPEED50

mm/sec25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec0.78

mm/sec0.39

mm/sec

PO+ET - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF



PO+ET


FREEZE SWITCH WAVES

VIEW ALARMS PRINT

ON OFFRefer to page 9-1

Refer to page 9-1

Refer to page 9-1

PO+ET - ALARM LIMITS

ETCO2 MINCO2 RESP I N2O SPO2 PULSE

PO+ET - ALARM LIMITS - PULSEPULSE HI =

XXLO = XX

ETCO2ON OFF PULSE

PO+ET - ALARM LIMITS - SPO2SPO2 HI =

XXLO = XX

SPO2ON OFF PULSE

PO+ET - ALARM LIMITS - I N2OI N2O HI =

XXLO = XX

I N2OON OFF SPO2

PO+ET - ALARM LIMITS - RESPRESP HI =

XXLO = XX

RESPON OFF I N2O

PO+ET - ALARM LIMITS - MINCO2MINCO2 HI =

XXMINCO2

ON OFF RESP

PO+ET - ALARM LIMITS - ETCO2ETCO2 HI =

XXLO = XX

ETCO2ON OFF MINCO2



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Selecting a Waveform Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
OverviewThe 90442A Flexport system interface enables information from a Biochem International BCI 9000 Capnograph-Oximeter to be displayed on Spacelabs Healthcare monitors.

Configure the oximeter as shown in Table 1. Consult the oximeter manual for additional configuration setup procedures

Table 1: Analyzer Configuration

Baud Rate


Installation Kit

Part Number


Part Number

9600 4.95G 045-0020-xx 131-0697-xx(25-pin)



Connecting the Flexport System InterfaceTo connect the Flexport system interface to the oximeter, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the oximeter. To control other interface functions, refer to the sections that follow.

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the oximeter.






• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 25-pin connector on the back of the oximeter.

� � � �

39 ETCO2 21 RESP PO+ET

96 SpO2

mmHg BPM %

1 MINCO2 0 I N2O 90 PULSE

mmHg % bpm

� � �

� � � �

PO+ET

SpO2= 96%PULSE= 90bpmETCO2= 39 mmHg

�MINCO2= 1 mmHg




� Current end tidal CO2 value

� Current respiration rate value

� PO+ET parameter key

� Current oxygen saturation value from pulse oximeter


� Current pulse rate value from pulse oximeter

� Current inspired N2O value

Current minimum CO2 value

Patient/room ID



• the PO+ET key flashes,



When all parameter alarms are turned OFF, alarm status messages will still cause the PO+ET key to flash.


Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the oximeter.

• Alarm tones on the oximeter can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.

� � � �

� SpO2= 96% RESP= 21BPM PO+ET

� PULSE= 90bpm I N2O= 0%

� ETCO2= 38mmHg

MINCO2= 1mmHg

ICU 14



Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the oximeter’s parameters (refer to Figure 9-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays PO+ET ALM OFF to the right of the PO+ET key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.



• Touch PO+ET.• Touch ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.To adjust alarm limits:• Select HI= or LO=.• Use arrow keys to adjust.


• Touch PO+ET.• Touch VIEW ALARMS.

PO+ET

96 SpO2

ETCO2 50 RESP 50 SpO2 1000 10 85 %

MINCO2 6 I N20 80 PULSE 120 88 PULSE0 40

bpm




Turning Waveform ON or OFFYou can turn waveforms OFF and display only the numeric values. When waveforms are OFF, the SWEEP SPEED key, the FREEZE ON/OFF keys, and the SIZE ↑ and SIZE ↓ keys are disabled.

The default setting is WAVEFORM ON.


Note:The WAVEFORM ON/OFF key must be set to ON for the size keys to appear and function.


• Touch PO+ET.• Touch SETUP.• Touch SIZE.• Select WAVEFORM ON/OFF.


• Touch PO+ET.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.



Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 50, 25, 12.5, 6.25, 3.12, 1.56, 0.78, and 0.39 mm/second. The minimum recorder sweep speed is 1.56 mm/second.

The default setting is 25 mm/second.






• Touch PO+ET.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.


• Touch PO+ET.• Touch SETUP.• Select LARGE TXT or SMALL TXT.


• Touch PO+ET.• Touch FREEZE ON.



Selecting a Waveform TypeYou can select either CO2 waveform or PULSE waveform for display. When the waveform is changed, a status message will briefly display stating the new type of waveform being displayed.

Note:• You can only change the waveform display at the bedside monitor.

• Changing the displayed waveform on the Spacelabs Healthcare monitor has no affect on the oximeter.



printout.



• Touch PO+ET.• Touch SWITCH WAVES.

To print the oximeter display:

• Touch PO+ET.• Touch PRINT.



Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the oximeter or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the oximeter is powered ON.


Table 2 lists the status messages that the Flexport system interface reports for the oximeter during Flexport system interface operation.



COMMUNICATION LINK LOSTCommunication between the oximeter and the Spacelabs Healthcare monitor has been interrupted.

Yes

DISPLAYING CO2 WAVE You have changed the displayed waveform to CO2 by touching SWITCH WAVES. No

DISPLAYING PLETH WAVE You have changed the displayed waveform to PLETH by touching SWITCH WAVES. No

CHECK SPO2 SENSOR The SpO2 sensor is disconnected or is not attached to the patient. No

OXIMETER MALFUNCTION Service required. No

APNEA An APNEA condition has been detected. Yes

OCCLUSION The CO2 sample line is blocked. Yes

WATER TRAP FULL The CO2 water trap is full; replace water trap. Yes

THERAPY PAUSEYou have pressed “Therapy Pause” on the oximeter. Monitoring of patient data has been suspended.

No

LOW CAL REQUIRED The oximeter requires calibration. Yes

HIGH CAL REQUIRED The oximeter requires calibration. Yes


Braun Fluid Management System

Directory of Keys

IV

IV - MAIN MENU


Refer to page 10-2

Refer to page 10-2


XXPUMP

XXPUMP

XXPUMP

XXPUMP

XXPUMP

XX ALL

PUMP XX

PUMP XX

PUMP XX

PUMP XX

PUMP XX

PUMP XX

IV - DISCONNNECT PUMP XX?YES NO

IV - EVENT MENUPUMP

XXPUMP

XXPUMP

XXPUMP

XXPUMP

XXPUMP

XX ALL

PUMP XX

PUMP XX

PUMP XX

PUMP XX

PUMP XX

PUMP XX



IV

IV - MAIN MENU


Refer to page 10-1

Refer to page 10-1

IV - SETUP MENUPUMP

XXPUMP

XXPUMP

XXPUMP

XXPUMP

XXPUMP

XX WEIGHT CHANGE CONFIG

PUMP XX

PUMP XX

PUMP XX

PUMP XX

PUMP XX

PUMP XX

IV - PUMP XX MENU

SELECT FLUID

SELECT DRUG

SELECT CONC.

SELECT DILUENT

DOSE CALCS

ALARMS

ON OFF

IV - HISTORY MENU IV - CHANGE CONFIGURATION - SELECT PARAMETER TO EDIT

PAGE ↑ PAGE ↓ PRINT EDIT DRUG EDIT FLUID


7 8 9

4 5 6

1 2 3

0 . CLEAR ENTER



Contents
OverviewThe 90437A-05 and 90437A-07 Flexport system interfaces enable information from a Braun Fluid Management System to be displayed on Spacelabs Healthcare monitors.

Caution:• 90437A-05 provides direct connection to the Braun Pump system. Connecting this unit to the

Braun Bedside Communication Controller (BCC) system may cause failure of the Braun BCC device.

• 90437A-07 provides connection to the Braun BCC system. This unit will not operate with the Braun Pump system.

Configure the infusion pump as shown in Table 1. Consult the appropriate infusion pump manual for additional configuration setup procedures.

Pump AddressesConnecting directly to Braun pumps or a Fluid Management System without a BCC:

The Spacelabs Healthcare monitor display identifies each IV pump by its address, which can range from 01 and 99. Braun refers to the pump address as the computer control (CC) address. Complete the steps provided in the following Quickstart to set the unique CC addresses, or refer to the Braun pump’s programmer’s guide.



Baud Rate Character Length


9600 8 bit none 1



Connecting to a Braun Fluid Management System with a Bedside Communication Controller (data concentrator):

The Spacelabs Healthcare monitor display identifies each IV pump by its location on the BCC. The address uses the relative panel number as the first digit and the relative pump number as the second digit. The computer control address (CC) on each pump must be set to 01 in order to communicate properly with the BCC device. Complete the steps provided in the above Quickstart to set the CC addresses or refer to the Braun pump’s programmer’s guide.

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the infusion pump, complete the steps in the following Quickstart.

To change the CC address on the Braun pump:

• Touch the SPECIAL FUNCTION key on the Infusomat fmS or Perfusor Compact until the CC-MODE screen appears.

• The current CC address is shown in the LED screen as Cxx, and in line 1 of the LCD as #xx (where xx is the current address).

• Touch C to clear the current address.• Select the desired CC address using the numeric keypad.• Touch END to permanently enter the new address.




Single pump or BCC:• Plug the other end of the modular cable into the appropriate transition connector.• Plug the transition connector into the Braun cable #871166/1.• Attach the other end of the Braun cable to the connector on the pump or the BCC.Multi-pump:• Plug the other end of the modular cable into the jack labeled FLEXPORT on the

multi-pump adaptor.• Plug another modular cable into one of the four IV pump jacks on the multi-pump

adapter.• Plug the other end into the appropriate transition connector.• Plug the transition connector into the Braun cable #871166/1.• Attach the other end of the Braun cable to the connector on the pump.• Repeat these steps for each additional pump.



Figure 10-1: Single pump configuration


The Spacelabs Healthcare monitor is now ready to display information from the infusion pump(s). To control other interface functions, refer to the sections that follow.

IVpumpor BCC

transitionconnector

modularcable

SDLCterminator

SDLCcable

P/N 871166/1Braun cable

SpacelabsHealthcare

monitor

systemFlexport

interface

IVpump

IVpump

IVpump

IVpump

modularcables

cableSDLC

SDLCterminator

transitionconnectors

multi-pumpadapter

Braun cablesP/N 871166/1

SpacelabsHealthcare

monitor

systemFlexport

interface



Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the infusion pump(s).

Figure 10-3: Bedside monitor screen

Note:The bedside monitor screen will expand to accommodate up to 12 pumps.

Figure 10-4: Remote or central monitor, full screen


� Pump address.



� � � � � � �


V12 PUMPING


� � � � � � �

P. STATUS RATE P. STATUS RATE P. STATUS RATE24 PUMP 52.3 g/hr 62 DISC 200.0 ml/hr I

V12 PUMP 22.1 mg/hr

88 PUMP 100.0 ml/hr 22 DONE 11.5 mcg/min 14 STOP 4.0 mcg/kg/min92 PUMP 24.3 mg/kg/hr 33 PUMP 210.0 mEq/hr 13 PUMP 250.0 ml/hr44 PUMP 21.3 mg/hr 63 PUMP 2.5 ml/kg/min 4 DONE 900.0 u/hr

� � � � � � �

PUMP STATUS PUMP STATUS PUMP STATUS24 PUMPING 62 DISCONN 12 PUMPING I

V88 PUMPING 22 INFUSN. D. 14 STOPPED92 PUMPING 33 PUMPING 13 PUMPING44 PUMPING 63 PUMPING 4 INFSN. D.



� Volume of fluids and the dose delivered since the last time one of the following conditions occurred:

• Pump starts a new dose.

• Pump rate is titrated.


� Pump’s latest status message (for example, PUMPING).

� Pump address and status.

Entering Setup InformationSetup information is necessary for the Spacelabs Healthcare monitor to display the drug (or fluid) names and to compute the medication and calculated pump rates. The SETUP key controls the following functions and affects only the monitor at which these adjustments are made:











Enabling AlarmsWhen alarms are turned OFF, the infusion pump alarms will no longer trigger an alarm on the Spacelabs Healthcare monitor.


Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the infusion

pump.

• Alarm limits on the Flexport system interface can only be adjusted at the infusion pump. Alarm violation is detected at the infusion pump and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• Alarm tones on the infusion pump can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.









D5 1/2 NS 20 KCL D5 1/4 NS D5W D10 NS

D10 1/2 NS D10 1/4 NS D10W NS





LR lactated ringers




D5 1/2NS 20KCL 5% dextrose with 0.45% saline and 20 mEq Potassium Chloride/Liter









NS 0.9% saline

1/2 NS 0.45% saline

1/4 NS 0.2% saline

TPN total parenteral nutrition

LIPIDS fat emulsion delivered as part of parenteral nutrition


• Touch IV.• Touch SETUP.• Select a pump key.• Touch SELECT FLUID.• Select a fluid from the list (or touch PAGE↓ and then select a fluid).• Touch ENTER.












ENTER

To select a drug:






To change a value after you have completed an initial drug/fluid entry, complete all of the steps listed in the following Quickstart. Figure 10-8 illustrates the Concentration screen.



system.



7 8 9 mcg mg /50 ml /100 ml

4 5 6 g ml /250 ml /500 ml


0 . CLEAR ENTER


• Touch IV.• Select SETUP.• Select a pump key.• Touch SELECT CONC.• Enter the drug quantity.• Select the unit of measurement.• Select the volume of fluid.• Touch ENTER.





To change your selection after you have completed an initial diluent entry, complete all of the steps listed in the following Quickstart.



If you have completed an initial drug/fluid entry and wish to change a value, complete all of the steps listed in the following Quickstart.


• Touch IV.• Touch SETUP.• Select a pump key.• Touch SELECT DILUENT.• Choose a diluent from the list (or touch PAGE↓ and then select a diluent).• Touch ENTER.





Note:If the interface displays an initial VOLUME INFUSED for the pump you intend to use, you must clear that value at the pump before you start an infusion. Otherwise, the Flexport system interface will appear to add the volume infused from the previous infusion to the current infusion.









1 2 3 units mEq






After you complete your editing and touch ENTER, the current weight will appear on the appropriate displays. You can enter up to six characters, including the decimal point. The valid weight range is from 1 to 250 kg (2 to 55 pounds). The interface saves the weight so you can use it in the Dose Calcs screen with the mcg/kg and mg/kg units of measurement.


7 8 9

4 5 6

1 2 3

0 . CLEAR ENTER









• Touch IV.• Select SETUP.• Touch CHANGE CONFIG.• Select EDIT DRUG or EDIT FLUID.• Select the name you want to change.• Touch CHANGE NAME.• Use alphanumeric keys to make necessary changes.• Touch ENTER.





CHANGE NAME




Figure 10-12: Change Drug Name screen



• Move through the name, character by character using the arrow keys.




After you complete your edit and touch ENTER, the name will appear in the appropriate display for selecting drugs or fluids. The interface saves the name so you can recall it the next time you connect the Flexport system interface.


0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J

K L M N O P Q R S T

U V W X Y Z / % .




Disconnecting a PumpWhen you touch DISCONNECT, the Flexport system interface discontinues the infusion record. If the pump is operating when you touch this key, the infusion record stops, a new record starts, and all pump setup information is cleared from the interface. If you touch DISCONNECT when the pump displays the status DISCONNECTED on the monitor, the setup information stored by the Flexport system interface is cleared and the line of pump data is removed from the display.



When you turn an infusion pump OFF at the pump itself, the pump status listed on the monitor changes to DISCONNECTED. At this point the interface completes the history for the current infusion (HISTORY shows the time that the infusion ended). If you turn ON the pump again, the interface continues to display the drug/fluid information entered previously.






To note an event:




Displaying Infusion HistoryInfusion history displays in a table format listing the last 40 infusion events for the patient on four pages (refer to Figure 10-13). This view-only table is available at the bedside monitor only and is not available for remote viewing.







DATE BEGAN ENDED PUMP DRUG/FLUID CONCENTRATION FLOW RATE VOL. INFSD








02/21 03:30am 07:00am 13 D5W 100.0 ml/hr 350.0 ml















Table 3 lists the status messages that the Flexport system interface reports for the pump on a central monitor, split screen.

Note:Not all messages will appear for each pump. Refer to the manual for your specific pump to determine which messages are used.

Table 3: Status Messages — Central Monitor, Split Screen


DISCONN Pump has been disconnected or turned OFF.

AIR ALARM Pump has detected air in IV tubing.


INFSN. D. Primary infusion is complete.


LOW BATT Battery requires recharging.

OCCLUSN Closed clamp, kinked, occluded tubing, or occluded filter detected.



PUMP OFF Pump on BCC is turned OFF.


IN STAND Pump is in a standby mode.

BOLUS RUN Bolus injection in progress.

STANDBY Pump’s standby time has expired.

DROP ALM Drop sensor problem detected.

CHK. SYR Syringe alarm has been detected.

COMM FAILURE Communication with Flexport failed.



Table 4 lists the status messages that the Flexport system interface reports for the pump on a remote monitor.

Table 4: Status Messages — Remote Monitor


DISC Pump has been disconnected or turned OFF.

AIR Pump has detected air in IV tubing.

DOPN Pump has detected an open door.

DONE Primary infusion is complete.


BATT Battery requires recharging.

OCCL Closed clamp, kinked, occluded tubing, or occluded filter detected.


PUMP Pump is pumping normally.

OFF Pump on BCC is turned OFF.

STOP Pump is stopped but not turned OFF.

STND Pump is in a standby mode or standby time expired.

BOLS Bolus injection in progress.

DROP Drop sensor problem detected.

SYRG Syringe alarm has been detected.



Table 5 lists the status messages that the Flexport system interface reports for the pump on a bedside monitor.

Table 5: Status Messages — Bedside Monitor



AIR ALARM Pump has detected air in IV tubing.





OCCLUSION Closed clamp, kinked, occluded tubing, or occluded filter detected.



PUMP OFF Pump on BCC is turned OFF.


IN STANDBY Pump is in a standby mode.

BOLUS RUN Bolus injection in progress.

STANDBY TIME Pump’s standby time has expired.

DROP ALARM Drop sensor problem has been detected.

CHK. SYRINGE Syringe alarm has been detected.

COMM FAILURE Communication with Flexport failed.



Criticare 504

Directory of Keys

SPO2

SpO2 - MAIN MENU

ALARM LIMITS SETUP

FREEZE VIEW ALARMS PRINT

ON OFF

SpO2 - SETUP

SIZE SWEEP SPEED

LARGE TXT

SMALL TXT

SpO2 - SETUP - SIZEWAVEFORM

SIZE ↑ SIZE ↓ON OFF

SpO2 - ALARM LIMITS SpO2 - SETUP - SWEEP SPEED

SpO2 HR 50 mm/sec

25 mm/sec

12.5 mm/sec

6.25 mm/sec

SpO2 - ALARM LIMITS - HRHR HI =

XXLO=XX

SPO2

ON OFF HR

SpO2 - ALARM LIMITS - SpO2SPO2 HI =

XXLO=XX

SPO2

ON OFF HR


Criticare 504

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OverviewThe 90442A Flexport system interface enables information from a Criticare 504 Pulse Oximeter to be displayed on Spacelabs Healthcare monitors.

Configure the pulse oximeter as shown in Table 1. Consult the pulse oximeter manual for additional configuration setup procedures.

Table 1: Pulse Oximeter Configuration

Baud Rate Installation Kit Part Number


Part Number


9600 045-0001-xx 131-0685-xx(25-pin) 3.5B6


Criticare 504

Connecting the Flexport System InterfaceTo connect the Flexport system interface to multiple pumps, complete the steps in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the pulse oximeter. To control other interface functions, refer to the sections that follow.




• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector on the pulse oximeter.


Criticare 504

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the pulse oximeter.




� SPO2 parameter key

� Current SpO2 (%) value


� SpO2 pulse rate

� Patient/room ID

� �

SPO2

97SpO2

%

68HR

bpm

� �

� �

SPO2

SpO2= 97%

HR= 68bpm

� �

� �

� SpO2= 97% SPO2

� HR = 68bpm

� ICU 14


Criticare 504



• the SPO2 key flashes,



When both parameter alarms are turned OFF, status alarms will not cause the SPO2 key to flash.


Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the pulse

oximeter.

• Alarm limits on can only be adjusted at the pulse oximeter. Alarm violation is detected at the pulse oximeter, and the Flexport system interface reports the alarm if it is turned on for that parameter.

• Alarm tones on the pulse oximeter can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the pulse oximeter’s parameters. If alarms for both parameters are turned OFF, the Spacelabs Healthcare monitor displays SPO2 ALM OFF to the right of the SPO2 key. If alarms are turned ON for either parameter, a bell is displayed instead. The alarm bell flashes when an alarm limit is violated.


• Touch SPO2.• Touch ALARM LIMITS.• Touch SPO2 or HR.• Touch the parameter alarm ON/OFF key.


• Touch SPO2.• Touch VIEW ALARMS.


Criticare 504







• Touch SPO2.• Touch SETUP.• Touch SIZE.• Select WAVEFORM ON/OFF.


• Touch SPO2.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.


Criticare 504

Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 6.25, 12.5, 25, and 50 mm/second.







• Touch SPO2.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.


• Touch SPO2.• Touch SETUP.• Select LARGE TXT or SMALL TXT.


• Touch SPO2.• Touch FREEZE ON.


Criticare 504



printout.



• Verify that the pulse oximeter is powered ON.


To print the pulse oximeter display:

• Touch SPO2.• Touch PRINT.


Criticare POET 601

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Viewing Trends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
OverviewThe 90434A-01 Flexport system interface enables information from a Criticare POET 601 analyzer to be displayed on Spacelabs Healthcare monitors.

Configure the analyzer as shown in Table 1. Consult the analyzer manual for additional configuration setup procedures.

To complete the configuration for the Criticare POET 601, use the analyzer’s configuration display to set the PO+ET serial interval to 1 second and the serial output format to ASCII printer.


Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number


19.2k 8-bit none 1 131-0685-xx (25-pin)

POET V1.3K, screen V1.6G


Criticare POET 601

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the analyzer, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the analyzer. To control other interface functions, refer to the sections that follow.




• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector on the analyzer.


Criticare POET 601

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the analyzer.


Figure 12-2: Bedside monitor, small text sceen




� Current EtCO2 (mmHg) value


� Current SaO2 (%) value

� Apnea monitoring status

� Patient/room ID

� � � �

21 RR PO+ET

24 ETCO2

BPM mmHg

97 SAO2

%

�

� � �

PO+ET

ETCO2 = 24 mmHgSAO2 = 97%RR = 21 BPM

� �

� �

� ETCO2 = 242 mmHg PO+ET

� SAO2 = 97%� RR = 21 BPM� APNEA = ON� ICU - 14


Criticare POET 601








Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the analyzer.

• Alarm tones on the analyzer can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.

Table 2: Alarm Limit Ranges

Parameter Valid Range

ETCO2 (mmHg)Low 0 to 79 mmHg

High 1 to 80 mmHg

Respiration (BPM)Low 0 to 199 BPM

High 1 to 200 BPM

Apnea (seconds) 5 to 55 seconds

SAO2 (%)Low 0 to 95%

High 5 to 100%


• Touch PO+ET.• Touch ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.To adjust alarm limits:• Select HI= or LO= (if applicable).• Use arrow keys to adjust.


Criticare POET 601

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the analyzer’s parameters (refer to Figure 12-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays PO+ET ALM OFF to the right of the PO+ET key. If alarms are turned ON for any parameter, a bell is displayed instead. The alarm bell flashes when an alarm limit is violated.








RR 45 ETCO2 56 PO+ET

24 ETCO2

15 16 mmHg

APNEA ON SAO2 100 97 SAO2

90 %


Criticare POET 601

Viewing TrendsThe TABULAR TRENDS key enables you to display trend data in tabular format, adjust the display interval from 1 to 60 minutes, and print the trend information.



To view trends:

• Touch PO+ET.• Touch TABULAR TREND.• Touch TIME INTERVAL.• Use the arrow keys to adjust. • Select PREV READING or NEXT READING to scroll through the data.

To print the analyzer display:



Criticare POET 601

Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the analyzer or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the analyzer is powered ON.


Table 3 lists the status messages that the Flexport system interface reports for the analyzer during Flexport system interface operation.




Communication between the analyzer and the monitor has been interrupted. Yes

APNEA No CO2 waveform for more than 20 seconds. Yes

CAPNOMETER OFF Capnometer is not turned ON. No

HIGH AMBIENT Ambient light or noise is being detected by the pulse oximeter sensor. Yes

MINIMUM INSPIRED Low flow condition, check airway adapter. Yes

OCCLUDED LINE Sample line is occluded or the pump is defective. Yes

OXIMETER OFF Oximeter is not turned ON. No

SEARCH Pulse is too weak. Yes

SENSOR OFF PATIENT

Too much light is being transmitted through the pulse oximeter monitoring site. Yes

SENSOR SIGNAL Sensor is not attached, needs to be moved, or is malfunctioning. No

WARMING UP Sensor is warming up or the analyzer has not completed calibrating the capnography sensor. No

WATER TRAP FULL Water trap needs to be replaced. Yes


Criticare POET-II 602-3

Directory of KeysPO+ET



ON OFFRefer to

page 13-2 These keys display on the

bedside monitor only

PO+ET - SETUP

SIZE SWEEP SPEED

LARGE TXTSMALL TXT

PO+ET - SETUP - SWEEP SPEED50

mm/sec25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec

PO+ET - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF




FREEZE SWITCH WAVES

VIEW ALARMS PRINT

ON OFFRefer to

page 13-1Refer to

page 13-1Refer to

page 13-1

PO+ET - ALARM LIMITS

SPO2 ETCO2 RESP I O2 I AGT E AGT

PO+ET - ALARM LIMITS - E AGTE AGT HI =

XXLO = XX

ETCO2ON OFF E AGT

PO+ET - ALARM LIMITS - I AGTI AGT HI =

XXLO = XX

I AGTON OFF E AGT

PO+ET - ALARM LIMITS - I O2I O2 HI =

XXLO = XX

I O2ON OFF I AGT

PO+ET - ALARM LIMITS - RESPRESP HI =

XXLO = XX

RESPON OFF I O2

PO+ET - ALARM LIMITS - ETCO2ETCO2 HI =

XXLO = XX

ETCO2ON OFF RESP

PO+ET - ALARM LIMITS - SPO2SPO2 HI =

XXLO = XXON OFF



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
OverviewThe 90442A Flexport system interface enables information from a Criticare 602-3 POET-II analyzer to be displayed on Spacelabs Healthcare monitors.


To complete the configuration for the analyzer, use the analyzer’s Configuration screen to set the POET serial interval to one second and the serial output format to “UNIV FLEXPORT” at 9600 baud.


Baud Rate Minimum Software Revision

Installation Kit

Part Number


Part Number

9600M4.2ES4.9

G4.70045-0002-xx 131-0685-xx (25-pin)










• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 25-pin connector on the back of the analyzer.

� � � � �

35 ETCO2 21 I O2 1.1 I AGTPO+ET

98 SpO2

mmHg % % %

16 RESP 0 I NO2 1.0 E AGT 70 PULSE

BPM % % bpm

� � �






� Current inspired oxygen value

� Current inspired agent value


� Current SpO2 value


� Current pulse rate value

Current expired agent value

Current inspired N2O value


� Patient/room ID

� � �

PO+ET

SpO2= 98%PULSE= 70bpmETCO2= 35mmHgI O2= 21%

� �

� ��

� SpO2= 98% I O2= 21% PO+ET

� PULSE= 70bpm I N2O= 0%

� ETCO2= 35mmHg I AGT=1.1%

� RESP= 16BPM E AGT=1.0%

� ICU 14











• Alarm limits can only be adjusted at the analyzer. Alarm violation is detected at the analyzer, and the Flexport system interface reports the alarm if it is turned ON for that parameter.



• Touch PO+ET.• Touch ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.












SpO2 1009264

0

RESP 660

5018

I AGT 5.00.05.00.0

PO+ET

98 SpO2

ETCO2 I O2 E AGT %

70 PULSE

bpm





Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 1.56, 3.12, 6.25, 12.5, 25 and 50 mm/second.












Freezing the Waveform on the DisplayThe FREEZE ON key enables you to freeze the waveform on the display. When you freeze the waveform, the Flexport system interface continues to process and update the numeric information.




printout.



• Touch PO+ET.• Touch FREEZE ON.












The communication between the Flexport system interface and the analyzer has been interrupted. Yes

GAS WARMING UP The CO2 and AGENT sensors are warming up in the PO+ET analyzer. No

GAS AUTOCAL The PO+ET device is performing a periodic automatic calibration. No

OCCLUDED The sample line is occluded or the pump is defective. Yes

APNEA No CO2 waveform has been detected for more than the set APNEA period. Yes

INSERT TRAP The water trap is not attached. Yes

REPLACE TRAP The water trap needs to be replaced. Yes

MIXED AGENT More than one agent type has been detected in measurable quantities. Yes

WRONG AGENT The agent detected does not match settings. Yes

SENSOR Too much light is being transmitted through the analyzer site or the SpO2 sensor is not attached to a patient. Yes

SENSOR SIGNAL The SpO2 sensor is not plugged into the PO+ET or is malfunctioning. Yes

HIGH AMBIENT Ambient light or noise is being detected by the analyzer. Yes

SPO2 SEARCH Pulse is too weak. Yes


Criticare POET IQ2

Directory of KeysPOET2

POET2 - MENUALARM LIMITS SETUP


ON OFFRefer to

page 14-2These keys are

displayed only on the bedside

monitor.

POET2 - SETUP

SIZE SWEEP SPEED

LARGE TXTSMALL TXT

POET2 - SETUP - SWEEP SPEED50

mm/sec25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec

POET2 - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF


Criticare POET IQ2

POET2 - MENUALARM LIMITS SETUP


ON OFFRefer to

page 14-1Refer to

page 14-1

POET2 - ALARM LIMITS

ETCO2 RESP I O2 I AGT E AGT

POET2 - ALARM LIMITS - E AGTE AGT HI =

XXLO = XXON OFF

POET2 - ALARM LIMITS - I AGTI AGT HI =

XXLO = XXON OFF

POET2 - ALARM LIMITS - I O2I O2 HI =

XXLO = XXON OFF

POET2 - ALARM LIMITS - RESPRESP HI =

XXLO = XXON OFF

POET2 - ALARM LIMITS - ETCO2ETCO2 HI =

XXLO = XXON OFF


Criticare POET IQ2

Contents
OverviewThe 90442A-03 Flexport system interface enables information from a Criticare POET IQ2 analyzer to be displayed on Spacelabs Healthcare monitors.

Note:If the factory default setting is selected all user-configured settings will be erased. You will have to reconfigure the output format settings for the POET IQ2 to function properly.

Configuring the POET IQ21 Configure the analyzer as shown in Table 1. Consult the analyzer manual for additional configuration setup

procedures.

2 Set the serial output format to “FLEX PRT” at 9600 baud using the Configuration screen.

3 Cycle the power to implement the configuration changes.

Table 1: Output Format Settings

Baud Rate Software RevisionInstallation

Kit Part Number


Part Number

9600 2.2 045-0160-xx 131-0686-xx


Criticare POET IQ2








interface.• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 25-pin connector on the back of the analyzer.

� � � �

35 ETCO2 21 I O2 1.1 I AGTPOET2

mmHg % %

16RESP

BPM 0I NO2

% 1.0E AGT

%

� � �

� � �

POET2

ETCO2= 35mmHgRESP= 16BPMI O2= 21%E AGT= 1.0%

� �


Criticare POET IQ2



� Current inspired oxygen value

� Current inspired agent value

� POET2 parameter key


� Current expired agent value

� Current inspired N2O value

Current respiration rate value

Patient/room ID

� � � ��

I O2= 21% POET2

I N2O= 0%

� ETCO2= 35mmHg I AGT=1.1%

RESP= 16BPM E AGT=1.0%

ICU 14


Criticare POET IQ2



• the POET2 key flashes,








• Touch POET2.• Touch ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


Criticare POET IQ2

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the analyzer’s parameters (refer to Figure 14-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays POET2 ALM OFF to the right of the POET2 key. If alarms are turned ON for any parameter, a bell is displayed instead. The alarm bell flashes when an alarm limit is violated.






• Touch POET2.• Touch VIEW ALARMS.


• Touch POET2.• Touch SETUP.• Touch SIZE.• Select WAVEFORM ON/OFF.

ETCO2 64 I O2 66 E AGT 5.0 POET2

0 0 0.0

RESP 66 I AGT 500 18


Criticare POET IQ2



Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 1.56, 3.12, 6.25, 12.5, 25 and 50 mm/second.





• Touch POET2.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.


• Touch POET2.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.


• Touch POET2.• Touch SETUP.• Select LARGE TXT or SMALL TXT.


Criticare POET IQ2





printout.



• Touch POET2.• Touch FREEZE ON.


• Touch POET2.• Touch PRINT.


Criticare POET IQ2








The communication between the Flexport system interface and the analyzer has been interrupted. Yes

GAS WARMING UP The CO2 and AGENT sensors are warming up in the POET2 analyzer. No

GAS AUTOCAL The POET2 device is performing a periodic automatic calibration. No

OCCLUDED The sample line is occluded or the pump is defective. No

APNEA No CO2 waveform has been detected for more than the set APNEA period. No

INSERT TRAP The water trap is not attached. No

REPLACE TRAP The water trap needs to be replaced. No

MIXED AGENT More than one agent type has been detected in measurable quantities. No

WRONG AGENT The agent detected does not match settings. No



Critikon Dinamap 1846 and 8100-Series

Directory of Keys

NIBP

NIBP - MAIN MENUALARM LIMITS PRINT PREV

READINGNEXT

READINGCHANGE CONFIG

NIBP - CHANGE CONFIGURATIONDISPLAY HR

ON OFF

NIBP - ALARM LIMITSALARMS HI=

150LO=100 ↑ ↓ SYS DIA MEAN

ON OFF


Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Displaying Heart Rate Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Displaying New or Previous Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Printing NIBP Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OverviewThe 90435A-01 and 90435A-02 Flexport system interfaces enable information from Critikon 1800 and 8100-series non-invasive blood pressure (NIBP) monitors to be displayed on Spacelabs Healthcare monitors.

Configure the NIBP monitor as shown in Table 1. Consult the NIBP monitor manual for additional configuration setup procedures.

Table 1: NIBP Monitor Configuration

Flexport Part Number and NIBP

Monitor

Baud Rate

Character Length

Parity Setting

Stop Bit

Transition Connector &Cable Part

Number


90435A-01; use with 1846-series Critikon NIBP devices

600 8 NO 1 131-0685-xx 26300 Rev. E or later

90435A-02; use with 8100-series Critikon NIBP devices

600 8 NO 1 131-1051-xx 8100RAH Rev. C or later



Connecting the Flexport System InterfaceTo connect the Flexport system interface to the NIBP monitor, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the NIBP monitor. To control other interface functions, refer to the sections that follow.




• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector on the NIBP monitor.



Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the NIBP monitor.

Figure 15-1: Bedside monitor with heart rate


� NIBP data table

� Current intervaI for automatic readings

� NIBP parameter key

� Last systolic and diastolic reading

� Last mean reading

� Alarm limits for systolic (HI=150; LO=100) and diastolic (HI=100; LO=60); asterisk (*) indicates alarm limits have been set for mean pressure

� X indicates alarm limits set on the NIBP monitor are being monitored by the Spacelabs Healthcare monitor

Date and time of last reading

Alarm status bell (appears when alarms are turned ON)

� Patient/room ID

� � � � �

INTERVAL q15 min

(109)22:03 140/ 72 (89) mmHg HR= 88 (NIBP) N

IBP

13322:18 128/ 67 (80) mmHg HR= 86 (NIBP) m 15022:33 132/ 67 (83) mmHg HR= 86 (NIBP) LAST BP = m X S * 10022:48 134/ 69 (85) mmHg HR= 86 (NIBP) 22:03 86 H D 10023:03 133/ 86 (109) mmHg HR= 82 (NIBP) 02/07 g 60

� �

� � � �

X NIBP

LAST BP =133/86 (109)mmHg 22:03

02/07� ICU 14



Displaying Heart Rate DataYou can display NIBP values with or without heart rate.

If you select DISPLAY HR OFF, 10 numerical readings are displayed. These 10 readings contain the following data:

• time of the reading

• systolic, diastolic, and mean blood pressure values

Displaying New or Previous ReadingsThe monitor can display up to 10 NIBP readings at one time and can store up to 30 readings. Touch PREV READING to scroll up one line. Touch NEXT READING to scroll down one line.

To display heart rate on NIBP table:

• Touch NIBP.• Touch CHANGE CONFIG.• Select DISPLAY HR ON.

To view NIBP readings not currently on the display:

• Touch NIBP.• Touch PREV READING or NEXT READING.





• the NIBP key flashes,



When alarms are turned OFF, alarm status messages will still cause the NIBP key to flash.

The default setting for alarms is OFF.

If alarms are turned OFF, the Spacelabs Healthcare monitor displays NIBP ALM OFF to the right of the NIBP key. If alarms are turned ON, a bell is displayed. The alarm bell flashes when an alarm limit is violated.

Note:Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the NIBP monitor.

Printing NIBP Readings You can print either the complete NIBP screen or only the numeric values of the last reading.


• Touch NIBP.• Touch ALARM LIMITS.• Select SYS, DIA, or MEAN.• Touch the parameter alarm ON/OFF key.To adjust alarm limits:• Select HI= or LO=.• Use arrow keys to adjust.

To print the NIBP screen:

• Touch NIBP.• Touch PRINT.

To print the most recent reading only:

• Touch RECORD.• Touch NIBP.



Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the NIBP monitor or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the NIBP monitor is powered ON.


Table 2 lists the status messages that the Flexport system interface reports for the NIBP monitor during Flexport system interface operation.



COMMUNICATION LINK LOSTCommunication between the NIBP monitor and the Spacelabs Healthcare monitor has been interrupted.

Yes

800 EXCESS PRESSURE

Excessive pressure has been caused by a kinked or pinched hose or cuff lead. Can also be caused by a quick patient motion, squeezing of the cuff, or an internal pneumatic system leak or failure.

Yes

802 CHECK INTERNAL DINAMAP SWITCHES

One or more of the internal dip switches is set wrong or has failed. Yes

811 DINAMAP VOLTAGE OUT OF LIMITS

One or more internal DC power supply voltages are out of tolerance. Yes

822 DINAMAP NEEDS PRESSURE CALIBRATION

Dinamap microprocessor is unable to set the proper zero offset at the beginning of a determination.

Yes

833 EXCESS TIME: INFLATION

Pneumatic pump cannot reach the target pressure within 40 seconds, usually due to a leak in the cuff or hose or due to an internal pneumatic system leak or failure.

Yes

844 EXCESS TIME: TOTAL READING

A measurement has not been completed and 120 seconds has elapsed since the reading was initiated, usually due to a leak in the cuff, hose, or connectors; excessive motion artifact; or an internal pneumatic system leak or failure.

Yes

855 EXCESS TIME: ONE PRESSURE LEVEL

Monitor senses the system pressure has remained at one pressure level either because no matched pulses were found or despite efforts to step down the pressure, usually caused by excessive motion artifact, arrhythmias, or a kinked or pinched cuff or hose.

Yes



866 DINAMAP RAM FAILUREIf the PULSE screen flashes 866, random access memory (RAM) has failed. If the display is blank, the microprocessor has failed.

No

877 DINAMAP ROM FAILUREIf the PULSE screen flashes 877, read-only memory (ROM) has failed. If the display is blank, the microprocessor has failed.

No

899 DETERMINATION UNSUCCESSFUL

NIBP monitor is unable to detect a strong enough signal to take a reading. Yes

Table 2: Status Messages (continued)




Datex Engström Erica/Elvira Ventilator

Directory of KeysVENT

VENT - MAIN MENU *

ALARM LIMITS SETUP

FREEZEVIEW MODE VIEW

STATUS PRINTON OFF

VENT - SETUPWAVE SIZE

↑SIZE

↓SWEEP SPEED

WAVETYPEON OFF

VENT - SETUP - SWEEP SPEED VENT - SETUP - WAVE TYPE25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec PRESS FLOW VOL

VENT - ALARM LIMITS * *

PIPPIP

VminVmin

RRRR

FiO2FiO2

VENT - ALARM LIMITS - FiO2FiO2 HI =

XXXLO = XXX

FiO2ON OFF PIP


XXXLO = XXX

RRON OFF FiO2


XXXLO = XXX

VminON OFF RR


XXXLO = XXX

PIPON OFF Vmin

*Available on the Elvira only.


Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail — Erica . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Display Detail — Elvira . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Viewing Ventilator Mode History (Elvira only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
OverviewThe 90436A-14 Flexport system interface enables information from a Datex Engström Erica or Elvira ventilator to be displayed on Spacelabs Healthcare monitors.

Configure the ventilator as shown in Table 1. Consult the appropriate ventilator manual for additional configuration setup procedures.

Note:• On the Erica ventilator, set the PRINTOUT INTERVAL knob to 10 seconds.

• On the Elvira ventilator, set the PRINTOUT INTERVAL knob to OFF and, in the setup program, set PRINT to TTY.

• To connect to the Erica ventilator, you must use the current loop-V24 converter option.


Ventilator Baud Rate

Character Length

Parity Setting

Stop Bit

Engström Elvira 9600 8-bit none 1

Engström Erica 300 7-bit odd 1



Figure 16-1: Modular cables



For Erica:• Connect the short branch of the SDLC cable to the 9-pin male connector on the

Flexport system interface.• Connect the 15-pin connector of the current loop-V24 converter to the printer

connection on the ventilator.• Connect the 9-pin connector of the modular cable (P/N 012-0544-xx) to the analog

recorder connection.• Attach one end of the modular cable to the 25-pin connector of the current

loop-V24 converter.• Plug the other end of the modular cable into the 8-pin receptacle on the Flexport system

interface.For Elvira:• Connect the short branch of the SDLC cable to the 9-pin male connector on the

Flexport system interface.• Connect the male 9-pin connector of the modular cable (P/N 012-0545-xx) to the

“analog out” connection.• Connect the female 9-pin connector of the modular cable to the printer

RS-232 connection.• Plug the other end of the modular cable into the 8-pin receptacle on the Flexport system

interface.

25-pin connector to Ericaventilator current loop-V24 converter

modular cable to Erica

modular cable to Elvira

9-pin connector to Elviraventilator analog out

9-pin connector to Erica ventilator analog recorder

9-pin connector to Elviraventilator printer RS-232



Figure 16-2: Elvira and Erica Flexport system interface connections


SDLCcable

SDLCterminator

modularcable

Erica

analogrecorder

Configuration for Erica

current loop-V24converter

SDLCcable

SDLCterminator

modularcable

Elvira

printer RS 232 connection

analog out connection

Configuration for Elvira

printer

SDLCconnector

SDLCconnector

connection

connection

SpacelabsHealthcare

monitor

SpacelabsHealthcare

monitor

systemFlexport

interface

systemFlexport

interface



Display Detail — EricaWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the Erica ventilator.

Figure 16-3: Erica — bedside monitor, large text screen

Figure 16-4: Erica — bedside monitor, small text screen

Figure 16-5: Erica — central monitor, split screen



� Spontaneous breath rate


� Tidal volume

� � � � � �

22 PIP 8 MAP 12 SRTVENT

1.22 VtWAVE=PRESSBPM L

cmH2O cmH2O SMV Vmin

20 PEEP 21 FiO2 14.6 14.6cmH2O % L L

� � �

� � �

VENT

Vt = 1.22 L WAVE=PRESSVmin = 14.6 L

PIP = 22 cmH2OPEEP = 20 cmH2O

� � �

� � �

� Vt = 1.22 L MAP = 8 cmH2O VENT

Vmin = 14.6 L SMV = 14.6 L

� PIP = 22 cmH2O SRT = 12 BPM

� PEEP = 20 cmH2O FiO2 = 21%

� �





Minute volume

Spontaneous minute volume

� Fractional inspired O2

� Positive end expiratory pressure

Display Detail — ElviraWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the Elvira ventilator.

Figure 16-6: Elvira — bedside monitor, large text screen

Figure 16-7: Elvira — bedside monitor, small text screen

� � � � � �

1.4 I:E 21 PIP 14.6 Vmin

VENT

1.22 VtWAVE=PRESSL

cmH2O L RR

22 FiO2 20 PEEP 18 MAP 12.2% cmH2O cmH2O BPM

� � �

� � �

VENT

Vt = 1.22 L WAVE=PRESSVmin = 12.2 BPM

PIP = 21 cmH2OI:E = 1.4

� � �



Figure 16-8: Elvira — central monitor, split screen

� Ratio of inspiration time to expiration time (I:E ratio is typically expressed as 1:X.X, where X.X is the value displayed and equals E/I) *

� Peak airway pressure

� Minute volume


� Tidal volume



Breath rate

Mean airway pressure


� Fractional inspired O2 **

* Values less than 1:1.0 are displayed as undefined.** The ventilator may display FiO2 but delay transmission to the Flexport system interface system for up to

seven minutes after turning ON the ventilator, exiting STAND BY mode, or adjusting the FiO2 setting. During this time, the Flexport system interface will show FiO2 as undefined.






When all Flexport system interface alarms are turned OFF, the status alarms will still cause the VENT key to flash.


� � � �

RR = 12.2 BPM I:E = 1.4 VENT

� FiO2 = 22% PIP= 21 cmH2O

� Vt = 1.22 L PEEP = 20 cmH2O

� Vmin = 14.6 L MAP = 8 cmH2O

�




• Alarm limits can only be adjusted at the ventilator. Alarm violation is detected at the ventilator, and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• The alarm limits are displayed as question marks when insufficient data is provided by the ventilator. The ventilator determines when the limits have been exceeded and the Flexport system interface will report the alarm condition.

• Alarm tones on the ventilator can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.

• When connected to the Elvira, the RR alarm follows the definition given in the Elvira manual:

- Low RR corresponds to Apnea.

and

- High RR corresponds to a high spontaneous breathing frequency.

Viewing StatusThe VIEW STATUS key enables you to display the recent status messages sent by the ventilator. A maximum of four messages can be displayed on the bedside monitor, and a maximum of three messages can be displayed on the remote monitor (refer to Status Messages on page 16-13).







Viewing Ventilator Mode History (Elvira only)Chronological history of the last eight ventilator mode settings are displayed in the waveform zone, with the most recent setting at the top of the left column and the oldest setting at the bottom of the right column. Possible modes include SIMV, EMMV, and CMV.

Figure 16-9: Ventilator mode history




To view ventilator mode:



• Touch VENT.• Touch SETUP.• Touch WAVE ON/OFF.

11:54 SIMV 11:41 CMV+SIGHVENT

Vt = 1.22L WAVE=PRESS11:53 EMMV 11:40 STAND BY RR= 12.2 BPM

11:51 SPONT. 11:27 CMV PIP = 21cmH2O11:50 TRIG. CMV I:E = 1.4







Selecting a Waveform TypeYou can select either pressure (PRESS), flow (FLOW), or volume (VOL) waveforms for display. The three waveform displays are mutually exclusive.




• Touch VENT.• Touch SETUP.• Select SWEEP SPEED.• Select the desired speed.


• Touch VENT.• Touch SETUP.• Touch WAVE TYPE.• Select desired wave type.





Selecting a Display FormatTwo display formats are available for the bedside monitor (refer to Display Detail — Erica on page 16-6 and Display Detail — Elvira on page 16-7).



printout.



• Touch VENT.• Select FREEZE ON.










• Verify that the printer interval knob is set to 10 seconds on the Erica or OFF on the Elvira.






AIR PRESS LO The supply air pressure has fallen below 265 kPa (2.7 kp/cm2). Yes

O2 PRESS LO The oxygen supply pressure has fallen below 265 kPa (2.7 kp/cm2). Yes

O2 ALARMEither the oxygen supply has fallen below 265 kPa (2.7 kp/cm2) or the FiO2 reading is outside the ventilator’s tolerance from the setting.

Yes

APNEA Apnea alarm. Yes

CHECK VENT Unknown alarm. Check the ventilator for greater detail. Yes


Datex Normocap CD2-02/CD-200

Directory of KeysGAS

GAS - MAIN MENUALARM LIMITS SETUP

FREEZE VIEW STATUS

VIEW ALARMS PRINT

ON OFFRefer to

page 17-2

GAS - SETUP MENU

WAVEFORM SIZE SWEEP SPEED

LARGE TXT PERCENT PERCENTSMALL TXT mmHg kPa

GAS - SETUP - SWEEP SPEED25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec

GAS - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF

GAS - SETUP - WAVEFORM

ETCO2 ETN2O ETO2



GAS


FREEZE VIEW STATUS

VIEW ALARMS PRINT

ON OFFRefer to

page 17-1

GAS - ALARM LIMITS

RR ETCO2 FiCO2 ETN2O FINO2 ETO2 FiO2 APNEA

GAS - ALARM LIMITS - APNEAALARM HI =

20APNEA

ON OFF RR

GAS - ALARM LIMITS - FiO2ALARM HI =

XXLO=XX ↑ ↓

FiO2ON OFF APNEA

GAS - ALARM LIMITS - ETO2ALARM HI =

XXLO=XX ↑ ↓

ETO2ON OFF FiO2

GAS - ALARM LIMITS - FINO2ALARM HI =

XXLO=XX ↑ ↓

FINO2ON OFF ETO2

GAS - ALARM LIMITS - ETN2OALARM HI =

XXLO=XX ↑ ↓

ETN2OON OFF FINO2

GAS - ALARM LIMITS - FICO2ALARM HI =

XXLO=XX ↑ ↓

FICO2ON OFF ETN2O

GAS - ALARM LIMITS - ETCO2ALARM HI =

XXLO=XX ↑ ↓

ETCO2ON OFF FICO2

GAS - ALARM LIMITS - RRALARM HI =

XXLO=XX ↑ ↓

RRON OFF ETCO2



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OverviewThe 90433A-07 Flexport system interface enables information from a Datex Normocap CD-200 or CD2-02 gas analyzer to be displayed on Spacelabs Healthcare monitors.

Configure the gas analyzer as shown in Table 1. Consult the appropriate analyzer manual for additional configuration setup procedures.


Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number


1200 8-bit none 1 131-1067-xx(25-pin)

Any version thatincorporates Protocol 1



Connecting the Flexport System InterfaceTo connect the Flexport system interface to the gas analyzer, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the gas analyzer. To control other interface functions, refer to the sections that follow.

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the gas analyzer.






• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector on the gas analyzer.

� � � � � �

[CO2]19 EtO2 39 EtN2O 21 RR

GAS

2.4 EtCO2

% % BPM %

21 FiO2 30 FiN2O 9.7 FiCO2

% % %

� �

� � �

[CO2]

GAS

EtCO2 = 24 mmHgFiCO2 = 9.7 mmHgRR = 21 BPM �FiN2O = 30%




Note:EtO2 and FiO2 values are not displayed on the Datex Normocap CD-200.

� Current expired oxygen (O2) value

� Current expired nitrous oxide (N2O) value


� GAS parameter key

� Current EtCO2 (mmHg or %) value

� Current waveform type


Current FiCO2 (mmHg or %) value

Current inspired nitrous oxide (N2O) value

� Current inspired oxygen (O2) value


Patient/room ID



• the GAS key flashes,



When all parameter alarms are turned OFF, alarm status messages will still cause the GAS key to flash.


� � � �

� EtCO2 = 2.4% RR = 21 BPMGAS

FiO2 = 9.7% APNEA = 20s

� EtN2O = 39% EtO2 = 19%

FiN2O = 30% FiO2 = 21%

ICU - 14

� �



Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the gas

analyzer.

• Apnea alarm limits can only be adjusted at the gas analyzer. Alarm violation is detected at the gas analyzer, and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• Alarm tones on the gas analyzer can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.

The Apnea alarm limit is fixed at 20 seconds and is determined by the gas analyzer. The EtCO2 and FiCO2 limits depend barometric pressure.


• Touch GAS.• Touch ALARMS LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.To adjust alarm limits:• Select HI= or LO=.• Use the arrow keys to adjust.



Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the gas analyzer’s parameters (refer to Figure 17-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays GAS ALM OFF to the right of the GAS key. If alarms are turned ON for any parameter, a bell is displayed instead. The alarm bell flashes when an alarm limit is violated.


Note:EtO2 and FiO2 values are not displayed on the Datex Normocap CD-200.

Viewing StatusThe VIEW STATUS key enables you to display recent status messages sent by the gas analyzer. A maximum of four messages can be simultaneously displayed on the bedside monitor. When more than four messages are received from the gas analyzer, they appear in the order they are received (refer to Status Messages on page 17-11). A maximum of three messages can be simultaneously displayed on the remote monitor.


• Touch GAS.• Touch VIEW ALARMS.

To view analyzer status:

• Touch GAS.• Touch VIEW STATUS.

[CO2]EtO2

21EtN2O

40RR

90EtCO2

5.2GAS

EtCO2 = 24 mmHg12 5 1 2.0 FiCO2 = 35 mmHg

RR = 21 BPM

FiO221

FiN2O80

APNEA20

FiCO26.0 FiN2O = 30%

18 0 4.0



Entering Setup InformationChanging setup information is helpful in optimizing the bedside monitor display. The SETUP key controls the functions described below and affects only the monitor at which these adjustments are made.

Selecting a Waveform TypeYou can select EtCO2, EtN2O, or EtO2 waveforms for display.

The default waveform is EtCO2.

Note:EtO2 is only available only with the Normocap CD2-02.




• Touch GAS.• Touch SETUP.• Touch WAVEFORM.• Select a waveform type.


• Touch GAS.• Touch SETUP.• Touch SIZE.• Select WAVEFORM ON/OFF.




Note:• The WAVEFORM ON/OFF key must be set to ON for the size keys to appear and function.

• When both the CD2-02 and CD-200 are “zeroing,” the waveform data will alternate between maximum and minimum values.

• The waveform will assume a tabular appearance that extends outside normal ranges.

Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 25, 12.5, 6.25 and 3.12 mm/second.





• Touch GAS.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.


• Touch GAS.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.


• Touch GAS.• Touch SETUP.• Select LARGE TXT or SMALL TXT.



Selecting a Unit of MeasurementYou can monitor gas values in units of percent (%), millimeters of mercury (mmHg), or kilo Pascals (kPa).





printout.


To select a unit of measurement:

• Touch GAS.• Touch SETUP.• Select PERCENT or mmHg or kPa.


• Touch GAS.• Touch FREEZE ON.


• Touch GAS.• Touch PRINT.






Table 2 lists the status messages that the Flexport system interface reports for the gas analyzer during Flexport system interface operation.




Communication between the gas analyzer and the monitor has been interrupted. Yes

O2 INOPER O2 sensor is inoperative. Yes

OCCLUSION An occlusion is detected. Yes

AIR LEAK An air leak is detected. Yes

REBREAT ALM A rebreathing alarm is detected. Yes

O2 ZERO ERROR Zeroing error. Yes

CO2 ZERO ERROR Zeroing error. Yes

N2O ZERO ERROR Zeroing error. Yes

ZERO VALUE Zero value error condition detected. Yes


Datex Ultima


GAS - MENUALARM LIMITS SETUP

FREEZE VIEW STATUS PRINT

ON OFFRefer to

page 18-2

GAS - SETUP MENU

SIZE SWEEPSPEED WAVEFORM

LARGE TXT DISPLAY SETUPSMALL TXT

GAS - DISPLAY SETUP

SET 1 SET 2 SAVE SET

GAS - WAVEFORM SETUP

CO2 O2 Pleth Pressure

GAS - SETUP - SWEEP SPEED25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec0.78

mm/sec0.39

mm/sec

GAS - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF


Datex Ultima

GAS

GAS - MENUALARM LIMITS SETUP

FREEZE VIEW STATUS PRINT

ON OFFRefer to

page 18-1Refer to

page 18-1Refer to

page 18-1Refer to

page 18-1

GAS - ALARM LIMITS

APNEA EtCO2 FiO2 PR MV Ppeak FiHAL SpO2

GAS - ALARM LIMITS - SPO2SpO2 HI =

ON/OFFLO =

ON/OFFAPNEA

ON OFF SpO2

GAS - ALARM LIMITS - FiHAL **FiHAL HI =

ON/OFFLO =

ON/OFFFiHAL

ON OFF SpO2

GAS - ALARM LIMITS - PpeakPpeak HI =

ON/OFFLO =

ON/OFFPpeak

ON OFF FiHAL

GAS - ALARM LIMITS - MVMV HI =

ON/OFFLO =

ON/OFFMV

ON OFF Ppeak

GAS - ALARM LIMITS - PRPR HI =

ON/OFFLO =

ON/OFFPR

ON OFF MV

GAS - ALARM LIMITS - FiO2FiO2 HI =

ON/OFFLO =

ON/OFFFiO2

ON OFF PR

GAS - ALARM LIMITS - EtCO2EtCO2 HI =

ON/OFFLO =

ON/OFFEtCO2

ON OFF FiO2

GAS - ALARM LIMITS - APNEAAPNEA APNEA

ON OFF EtCO2


Datex Ultima

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OverviewThe 90443A-04 Flexport system interface enables information from a Datex Ultima gas monitor to be displayed on Spacelabs Healthcare monitors.

Configure the gas monitor as shown in Table 1. Consult the gas monitor manual for additional configuration setup procedures.

Table 1: Gas Monitor Configuration

Baud Rate

Character Length

Parity Setting

Stop Bit

InterfaceCable


1200 8 bit N 1 25 pin879016-2.2 (3 agents)882916-3.1 (5 agents)


Datex Ultima

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the gas monitor, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the gas monitor. To control other interface functions, refer to the sections that follow.

Display DetailWhen you power ON a bedside monitor that is properly connected to a Flexport system interface, the monitor displays data from the gas monitor (if powered ON) in one of four displays:

• Large text, Set 1 (factory default)

• Large text, Set 2

• Small text, Set 1

• Small text, Set 2

The default can be changed by touching SAVE SET while the desired data set is active.

Note:Information from the gas monitor is sent to the Flexport system interface at 10-second intervals. It may take up to 10 seconds for the data from the gas monitor to appear on the Spacelabs Healthcare monitor.



• Plug one end of the modular cable into the 8-pin receptacle on the Flexport system interface.

• Plug the 25-pin connector on the other end of the modular cable into the RS-232 connector on the gas monitor labeled DIGITAL OUTPUT.

• Plug the 9-pin connector into the analog output connector on the side of the gas monitor.


Datex Ultima

Figure 18-1: Set 1, large text screen

Figure 18-2: Set 1, small text screen

Figure 18-3: Set 1, split screen, central monitor

� � � � � � �

20 FeN2O 1.7 FeAGT 44FeO2 12 RR

GAS

4.9EtCO2 WAVE=

CO2% % % BPM %

14 FiN2O 2.5 FiAGT 50FiO2 99 SpO2 0.7 FiCO2% % % % %

� � �

� � �

GAS

EtCO2= 4.9% WAVE=CO2RR = 12 BPM �

FiO2 = 50% �FiAGT = 2.5%FiN2O = 14%

�

� � �

� EtCO2 = 4.9% FiCO2 = 0.7%GAS

� RR = 12 BPM SpO2 = 99%

� FeO2 = 44% FiO2 = 50%

� FeAGT = 1.7% FiAGT = 2.5%

� FeN2O = 20% FiN2O = 14%

� ICU 14

�


Datex Ultima

Figure 18-4: Set 2, large text screen

Figure 18-5: Set 2, small text screen

Figure 18-6: Set 2, split screen, central monitor

� Current expired nitrous oxide value

� Current expired anesthetic agent value

� Current expired fraction O2 value

� Current respiratory rate



� Current waveform mode


� � � � �

21 Ppeak 99 SpO2

GAS

4.9EtCO2

WAVE=CO2

cmH2O % %

1.22 MV 72 PR 0.7 FiCO2

L/min bpm %

� �

� � �

WAVE= CO2

GAS

EtCO2 = 4.9%

SpO2 = 99% �Ppeak = 21 CmH20MV = 1.22 L

� �

� �

� EtCO2= 4.9% FiCO2 = 0.7%GAS

� Ppeak = 21 cmH2O MV = 1.22 L

� SpO2 = 99%

� ICU - 14


Datex Ultima

Current inspired fraction CO2 value


� Current inspired fraction O2 value

Current inspired anesthetic agent value (with mixed agent, secondary agent displays below primary agent)

� Current inspired nitrous oxide value

� Patient/room ID


� Current minute volume

� Current pulse rate






When an alarm is OFF, the high and low alarm limits are displayed as OFF. When an alarm is turned ON, the high and low limits are displayed as ON. When an alarm is active, the actual alarm limit is displayed in either the HI= limit or the LO= limit key.


Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the gas monitor.

• Alarm violation is detected at the gas monitor, and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• Alarm tones on the gas monitor can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.

• Alarm limit values are not available for the Minute Volume (MV) alarm. When this alarm is active, the HI or LO key flashes and the key continues to display ON instead of the alarm limit. The alarm limit values can be viewed on the gas monitor.


• Touch GAS.• Touch ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


Datex Ultima

Viewing StatusThe VIEW STATUS key enables you to display the recent status messages sent by the gas monitor. A maximum of four messages can be simultaneously displayed on the bedside monitor. When more than four messages are received from the gas monitor, they appear in the order they were received (refer to Status Messages on page 18-11). A maximum of three messages can be simultaneously displayed on the remote monitor.

Entering Setup InformationChanging setup information is helpful in optimizing the Spacelabs Healthcare monitor display. The SETUP key controls the functions described below and affects only the monitor at which these adjustments are made.



To view status:

• Touch GAS.• Touch VIEW STATUS.




Datex Ultima



Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 0.39, 0.78, 1.56, 3.12, 6.25, 12.5, and 25 mm/second.


Selecting a Waveform TypeYou can select CO2, O2, PLETH, or PRESSURE waveforms for display. You can set PRESSURE from the gas monitor Setup menu.






• Touch GAS.• Touch SETUP.• Touch WAVEFORM.• Select a waveform type.


Datex Ultima

Selecting a Display SetupTwo sets of patient data (SET 1 or SET 2) can be displayed on Spacelabs Healthcare monitors (refer to Display Detail on page 18-4). Bedside and remote monitors can be independently set. Touching SAVE SET will save the currently displayed set as the power ON default, including the LARGE TXT/SMALL TXT setting. (SMALL TXT is not available on a remote monitor.)



Printing the Current DisplayTouch the PRINT key to print the information shown on the current display. Each recording is identified by the bed name, patient name, time, and date


printout.


To select a display setup:

• Touch GAS.• Touch SETUP.• Touch DISPLAY SETUP.• Touch SET 1 or SET 2.• Touch SAVE SET to save display set 1 or 2.


• Touch GAS.• Touch FREEZE ON.


Datex Ultima

Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the gas monitor or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the gas monitor is powered ON.


Table 2 lists the status messages that the Flexport system interface reports for the gas monitor during Flexport system interface operation.

To print the gas monitor display:





Communication between the gas monitor and the Spacelabs Healthcare monitor has been interrupted. Yes

CO2 ZERO ERROR Condensation or residual gases are affecting zero measurement. No

O2 ZERO ERROR Condensation or residual gases are affecting zero measurement. No

N2O ZERO ERROR Condensation or residual gases are affecting zero measurement. No

AGNT ZERO ERROR Condensation or residual gases are affecting zero measurement. No

REBREATH ALARM Inhaled (FICO2) concentration is higher than rebreathing limit. No

AIR LEAK Water trap is not connected, gas outlet is blocked, or leak in line. No

OCCLUSION Sampling line or the internal tubing is blocked. No

AGENT EXPIRE LO Expiratory anesthetic agent exceeds lower alarm limits. No

AGENT EXPIRE HI Expiratory anesthetic agent exceeds high alarm limits. No

LO PLETH SIGNAL Pulse wave amplitude is low and irregular. No

PULSE SEARCH Monitor is searching for a pulse. No


Datex Ultima

PROBE OFF SpO2 probe is not attached to patient, or contact is loose. No

NO SPO2 PROBE SpO2 probe is not connected to monitor. No

OBSTRUCTION Tubes or airway is obstructed. No

DISCONNECTION Tubes or double lumen tube disconnected. No

LEAK Leak alarm is activated if there is a leak distal to D-LITE adapter. No




Dräger Cato

Directory of KeysANES

ANES - MAIN MENUALARM LIMITS SETUP

FREEZE VIEW STATUS

VIEW ALARMS PRINT

ON OFFRefer to

page 19-2

ANES - SETUP



ANES - SETUP - SWEEP SPEED25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec

ANES - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF

ANES - SETUP - WAVEFORM TYPE

EtCO2 FLOW


Dräger Cato

ANES


FREEZE VIEW STATUS

VIEW ALARMS PRINT

ON OFFRefer to

page 19-1

ANES - ALARM LIMITS

EtCO2 FiAGT* FiO2 PIP Vmin

ANES - ALARM LIMITS - VminALARM HI =

XX.XLO = XX.X

VminON OFF EtCO2

ANES - ALARM LIMITS - PIPALARM HI =

XXXLO = XXX

PIPON OFF Vmin

ANES - ALARM LIMITS - FiO2ALARM HI =

XXXLO = XXX

FiO2ON OFF PIP

ANES - ALARM LIMITS - FiAGT*ALARM HI =

XXXLO = XXX

FiAGT*ON OFF FiO2

ANES - ALARM LIMITS - EtCO2ALARM HI =

XXLO = XX

EtCO2ON OFF FiAGT*

* FiAGT can also be FiDES, FiENF, FiHAL, FiISO, or FiSEV.


Dräger Cato

Contents
OverviewThe 90443A-08 Flexport system interface enables information from a Dräger Cato anesthesia machine to be displayed on Spacelabs Healthcare monitors.

Configure the anesthesia machine as shown in Table 1. Consult the anesthesia machine manual for additional configuration setup procedures.

Table 1: Anesthesia Machine Configuration

Baud Rate

Character Length

Parity Setting

StopBit

Minimum Medibus Protocol

9600 8 bit even 1 3.00


Dräger Cato

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the anesthesia machine, complete the steps listed in the following Quickstart.

The monitor is now ready to display information from the anesthesia machine. To control other interface functions, refer to the sections that follow.

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the anesthesia machine.





• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector on the anesthesia machine.

� � � � � �

0.89FiAGT

22RR

11.2Vmin

ANES

0.49 Vt [FLOW]

% BPM L L

35EtCO2

39PIP 30 FiO2

mmHg mbar %

� �


Dräger Cato

Figure 19-2: Bedside monitor, small text


� Fractional inspired agent value can be FiHAL, FiDES, FiISO, FiENF, FiSEV, or FiAGT (if the agent is halothane, desflurane, isoflurane, enflurane, sevoflurane, or mixed/unidentified, respectively)

� Respiratory rate value

� Minute volume value

� ANES parameter key

� Expired tidal volume value



Fraction inspired O2 value

Peak inspiratory pressure value

� End tidal CO2 value

� � �

[FLOW]ANES

FiO2=30%RR= 22BPMEtCO2=35mmHgVt= 0.49L

� � �

� � �

� EtCO2=35mmHg FiO2=30%%ANES

� RR=22BPM PIP=39mbar

� Vt=0.49L FiAGT=0.89%

� Vmin=11.2L


Dräger Cato



• the ANES key flashes,



When all parameter alarms are turned OFF, status alarms will still cause the ANES key to flash.


Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the anesthesia

machine.

• Alarm limits can only be adjusted at the anesthesia machine. Alarm violation is detected at the anesthesia machine and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• Alarm tones on the anesthesia machine can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.


• Touch ANES.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


Dräger Cato

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the anesthesia machine’s parameters (refer to Figure 19-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays ANES ALM OFF to the right of the ANES key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.



• Touch ANES.• Touch VIEW ALARMS.

FiAGT 2.00 PIP 40 Vmin20.

0 ANES

FiO2=21%

0.50 4 4.0 RR= 22BPMEtCO2=35mmHg

EtCO2 75 FiO2 45 Vt= 0.49L00 18


Dräger Cato

Viewing StatusThe VIEW STATUS key enables you to display recent status messages sent by the anesthesia machine. A maximum of four messages can be simultaneously displayed on the bedside monitor, and three can be simultaneously displayed on the remote monitor (refer to Status Messages on page 19-11).

Figure 19-5: View Status screen


Selecting a Waveform TypeYou can select either expired CO2 (EtCO2) or flow waveforms for display.

To view anesthesia machine status:

• Touch ANES.• Touch VIEW STATUS.


• Touch ANES.• Touch SETUP.• Touch WAVEFORM.• Select EtCO2 or FLOW.

ANES

FiO2=30%

-- APNEA CO2 RR= 22BPM

-- CAL % O2 EtCO2=35mmHg

-- PRESSURE LTD Vt= 0.49L


Dräger Cato





Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 3.12, 6.25, 12.5, and 25 mm/second.



• Touch ANES.• Touch SETUP.• Touch SIZE.• Select WAVEFORM ON/OFF.

To change waveform size:

• Touch ANES.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.


• Touch ANES.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.


Dräger Cato



Selecting Units for Expired CO2Expired CO2 can be displayed in units of percent (%), millimeters of mercury (mmHg), or kilo Pascals (kPa). The selection of mmHg or kPa is a function of the monitor’s setting. The units can be switched between the original setting and percent.



• Touch ANES.• Touch SETUP.• Select LARGE TXT or SMALL TXT.

To select EtCO2 units:

• Touch ANES.• Touch SETUP.• Select units.


• Touch ANES.• Select FREEZE ON.


Dräger Cato



printout.


Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the anesthesia machine or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the anesthesia machine is powered ON.


Table 2 lists the status messages that the Flexport system interface reports for the anesthesia machine during Flexport system interface operation.




Communication between the anesthesia machine and the monitor has been interrupted. Yes

CO2/AGT ERR Multigas monitor device failure. Yes

N2O ERR N2O measurement inoperable. Yes

AGT ERR Agent measurement inoperable. Yes

AGT WARM UP Agent monitor in low accuracy mode (warm up). No

AGT NOT SEL Agent not selected. No

APNEA VOL Apnea — no volume exhaled for 30 seconds. Yes

VOL CAL ? Flow calibration necessary. Yes

PAW NEGATIVE Mean airway pressure < -2 mbar. Yes

PRESS ERR Pressure measurement inoperable. Yes

AW-TMP INOP Airway temperature measurement inoperable. Yes


Dräger Cato

AW-TEMP HIGH Airway temperature > high limit. Yes

APNEA CO2 Apnea — no CO2 fluctuations for 30 seconds. Yes

INSP CO2 HI Inspiratory CO2 >high limit. Yes

CO2 LINE BLK CO2 patient sensor line blocked. Yes

CO2 ALRM OFF CO2 alarm disabled. Yes

CO2 WARM UP CO2 monitor in low accuracy mode (warm up). No

CO2 ERR CO2 device failure. Yes

SPEAKER FAIL Primary speaker failure. Yes

PM8050 ERR Hardware problem PM8050. Yes

COOLING PM8050 Check PM8050 cooling. Yes

CAL % O2? Oxygen analyzer not calibrated. No

% O2 $& <21 Inspiratory oxygen low limit <21%. No

% O2 ERR Inspiratory O2 measurement inoperable (alarm). Yes

FRESH GAS ? Check gas supply. Yes

PRESS EXP HI Expiratory pressure > high limit. Yes

VENT ERR Problems with anesthesia machine. Yes

COM VENT ERR Anesthesia machine communication lost. Yes

EXP-VALVE ? Check expiration-valve. Yes

PRESSURE LTD Pressure limited respiratory volume. No





Dräger Cicero B


VENT - MAIN MENUALARM LIMITS

LARGE TXT VIEW STATUS

VIEW ALARMS PRINT

SMALL TXT

VENT - ALARM LIMITS

EtCO2 SpO2 NIBP I.AGT FiO2 PIP Vmin

VENT - ALARM LIMITS - VminALARM HI =

XX.XLO = XX.X

VminON OFF EtCO2

VENT - ALARM LIMITS - PIPALARM HI =

XXXLO = XXX

PIPON OFF Vmin

VENT - ALARM LIMITS - FiO2ALARM HI =

XXXLO = XXX

FiO2ON OFF PIP

VENT - ALARM LIMITS - I.AGTALARM HI =

X.XXLO = X.XX

I.AGTON OFF FiO2

VENT - ALARM LIMITS - NIBPALARM HI =

XXXLO = XXX

NIBPON OFF I.AGT

VENT - ALARM LIMITS - SpO2ALARM HI =

XXXLO = XXX

SpO2ON OFF NIBP

VENT - ALARM LIMITS - EtCO2ALARM HI =

XXLO = XX

EtCO2ON OFF SpO2

Dräger Cicero B

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OverviewThe 90443A Flexport system interface enables information from a Dräger Cicero B ventilator to be displayed on Spacelabs Healthcare monitors.



Baud Rate

Character Length

Parity Setting

Stop Bit


9600 8 bit even 1 3.00


Dräger Cicero B








• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector on the ventilator.

� � � � � �

120 SYS 0.89I.AGT

22RR

11.2Vmin

VEET

0.49Vtexp

99 MEAN % BPM L L

60 DIA

59EtCO2

39PIP

98SpO2 30

FiO2

%NIBP mmHg mmHg mbar %

� � �


Dräger Cicero B



� NIBP systolic, mean and diastolic blood pressure values

� Inspired agent value







Pulse oximetry O2 saturation value

� Peak inspiratory pressure value

� End tidal CO2 value

� �

VEET

EtCO2=59mmHgRR= 22BPM �Vtexp=0.49L �SpO2=98%

�

� � � �

� EtCO2=59mmHg FiO2=30%%

VENT

� RR=22BPM SpO2 = 98%

� Vtexp=0.49L PIP=39mbar

� Vmin=11.2L NIBP= 120/60mmHg


Dräger Cicero B












• Touch VENT.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


Dräger Cicero B

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the ventilator’s parameters (refer to Figure 20-4). If alarms for all ventilator parameters are turned OFF, the Spacelabs Healthcare monitor displays VENT ALM OFF to the right of the VENT key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.


Viewing StatusThe VIEW STATUS key enables you to display the recent status messages sent by the ventilator. A maximum of four messages can be simultaneously displayed on the bedside monitor, and three can be simultaneously displayed on the remote monitor (refer to Status Messages on page 20-9).





NIBP 150 I.AGT 2.00 PIP 40 Vmin 20.0 ANES

EtCO2=22mmHg70 0.50 4 4.0 RR= 20BPM

Vtexp=0.49L

EtCO2 75 SpO2 100 FiO2 45 SpO2= 96%00 85 18


Dräger Cicero B







To print a ventilator display:



Dräger Cicero B







COMMUNICATION LINK LOST Communication between the ventilator and the monitor has been interrupted. Yes


N2O ERR N2O measurement inoperable. Yes

AGT ERR Agent measurement inoperable. Yes

A-VAP OFF Iris function disabled. Yes

AGT ALRM OFF Agent alarm disabled. Yes

AGT WARM UP Agent monitor in low accuracy mode (warm up). Yes

AGT NOT SEL Agent not selected. Yes

A-VAP CAL? Iris calibration necessary. Yes

A-VAP ERR Iris function inoperable. Yes

CHECK VAPOR Vapor not connected, known, or allowed. Yes


APNEA PRES Apnea — pressure absent for 15 seconds. Yes

VOL ALRM OFF Volume alarm disabled. Yes

VOL CAL? Flow calibration necessary. Yes

VOL ERR Volume measurement inoperable (alarm). Yes


AW-TMP INOP Airway temperature measurement inoperable. Yes



Dräger Cicero B

APNEA CO2 Apnea — no CO2 fluctuations for 30 seconds. Yes

INSP CO2 HI Inspiratory CO2 >high limit. Yes


APN.CO2’@OFF Apnea CO2 alarm disabled. Yes

CO2 ALRM OFF CO2 alarm disabled. Yes

CO2 WARM UP CO2 monitor in low accuracy mode (warm up). Yes


MAN/SP’@MODE Manual spontaneous alarm mode ON. Yes

VENTMON COM? Communication error ventilator port. Yes

ECG COM ERR Communication error ECG-monitor port. Yes

INT COM ERR Internal communication error. Yes

PM8035 ERR Hardware problem PM 8035. Yes

PM8035 STBY PM 8035 standby. Yes

PM8035 TEST Self check PM 8035. Yes

BP CUFF ERR NIBP cuff improperly placed. Yes

BP CUFF DISC NIBP cuff disconnected or leaking. Yes

NIBP STANDBY NIBP monitor in standby mode. Yes

NIBP ERR NIBP device failure. Yes

CAL% O2? Oxygen analyzer not calibrated. Yes

% O2 ERR Inspiratory O2 measurement inoperable (alarm). Yes

NO SAO2 PULS No SAO2 pulse for 10 seconds. Yes

SAO2SEN DISC SaO2 sensor disconnected or fault. Yes

SAO2 ALRM OF Oximeter alarm disabled. Yes

SAO2 ERR Oximeter device failure. Yes

FRESH GAS? Check gas supply. Yes




Dräger Cicero B


VENT ERR Problems with ventilator. Yes

COM VENT ERR Ventilator communication lost. Yes

EXP-VALVE? Check expiration-valve. Yes

PRESSURE LTD Pressure limited respiratory volume. Yes

MIN VOL LOW Minute volume less than low limit. Yes




Dräger Cicero EM



FREEZE VIEW STATUS

VIEW ALARMS PRINT

ON OFFRefer to

page 21-2

ANES - SETUP




mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec


↑SIZE

↓ON OFF

ANES - SETUP - WAVEFORM

EtCO2 PRESSURE


Dräger Cicero EM

ANES


FREEZE VIEW STATUS

VIEW ALARMS PRINT

ON OFFRefer to

page 21-1

ANES - ALARM LIMITS

EtCO2 SpO2 NIBP FiAGT* FiO2 PIP Vmin

These keys appear only if data has been received.

ANES - ALARM LIMITS - VminALARM HI =

XX.XLO = XX.X

VminON OFF EtCO2

ANES - ALARM LIMITS - PIPALARM HI =

XXXLO = XXX

PIPON OFF Vmin

ANES - ALARM LIMITS - FiO2ALARM HI =

XXXLO = XXX

FiO2ON OFF PIP

ANES - ALARM LIMITS - FiAGT*ALARM HI =

X.XXLO = X.XX

FiAGT*ON OFF FiO2

ANES - ALARM LIMITS - NIBPALARM HI =

XXXLO = XXX

NIBPON OFF FiAGT

ANES - ALARM LIMITS - SpO2ALARM HI =

XXXLO = XXX

SpO2ON OFF NIBP

ANES - ALARM LIMITS - EtCO2ALARM HI =

XXLO = XX

EtCO2ON OFF SpO2

*FiAGT can also be FiDES, FiENF, FiHAL, FiISO, or FiSEV


Dräger Cicero EM

Contents
OverviewThe 90443A-09 Flexport system interface enables information from a Dräger Cicero EM anesthesia machine to be displayed on Spacelabs Healthcare monitors.



Baud Rate

Character Length

Parity Setting

Stop Bit


9600 8-bit even 1 3.00


Dräger Cicero EM


The Spacelabs Healthcare monitor is now ready to display information from the anesthesia machine. To control other interface functions, refer to the sections that follow.






• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector on the anesthesia machine.

� � � � � � �

120 SYS 0.89FiAGT

22 RR 11.2Vmin

ANES

0.49Vt PRES

99 MEAN % BPM L L

60 DIA

59EtCO2

39PIP

98SpO2 30

FiO2

%NIBP mmHg mmHg mbar %

� �


Dräger Cicero EM



SpO2 and NIBP are only displayed if data is available.

� NIBP systolic, mean, and diastolic blood pressure values

� Inspired agent value





� PRES or ETCO2, depending upon waveform type selected



� Pulse oximetry O2 saturation value


End tidal CO2 value

�

ANES

FiO2=30%RR= 22BPM �EtCO2=59mmHg Vt= 0.49L

�

� ��

EtCO2=59mmHg FiO2=30%%

ANES

� RR=22BPM SpO2 = 98%

� Vtexp=0.49L PIP=39mbar

� Vmin=11.2L NIBP= 120/60mmHg


Dräger Cicero EM









machine.






Dräger Cicero EM



Viewing StatusThe VIEW STATUS key enables you to display the recent status messages sent by the anesthesia machine. A maximum of four messages can be simultaneously displayed on the bedside monitor, and three messages can be simultaneously displayed on the remote monitor (refer to Status Messages on page 21-11).



To view the anesthesia machine status:


FiAGT 2.00 PIP 40 Vmin 20.0 ANES

EtCO2=22%0.50 4 4.0 RR= 20BPM

EtCO2=49mmHg

NIBP 150 EtCO275 SpO2

100 FiO245 Vt= L

70 00 85 18


Dräger Cicero EM


Selecting a Waveform TypeYou can select either expired CO2 (EtCO2) or pressure waveforms for display.

Turning Waveforms ON or OFFYou can turn waveforms OFF and display only numeric values. When waveforms are OFF, the FREEZE ON/OFF keys, the SWEEP SPEED key, and the SIZE ↑ and SIZE ↓ keys are disabled.


To select a waveform:

• Touch ANES.• Touch SETUP.• Touch WAVEFORM.• Select ETCO2 or PRESSURE.




Dräger Cicero EM



Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 3.12, 6.25, 12.5, and 25 mm/second.











Dräger Cicero EM

Selecting Units for Expired CO2Expired CO2 can be displayed units of percent (%), millimeters of mercury (mmHg), or kilo Pascals (kPa). The selection of mmHg or kPa is a function of the monitor’s setting. The units can be switched between the original setting and percent (%).




printout.


To select expired CO2 units:

• Touch ANES.• Touch SETUP.• Select units.



To print the anesthesia machine display:

• Touch ANES.• Touch PRINT.


Dräger Cicero EM


• Verify that the anesthesia machine is turned ON.





COMMUNICATION LINK LOST Communication between the anesthesia machine and the monitor has been interrupted. Yes


N2O ERR N2O measurement is inoperable. Yes

AGT ERR Agent measurement is inoperable. Yes

AGT WARM UP Agent monitor in low accuracy mode (warm up). No

AGT NOT SEL Agent not selected. No


VOL CAL? Flow calibration necessary. No

PAW NEGATIVE Mean airway pressure < -2 mbar. Yes

PRESS ERR Pressure measurement is inoperable. Yes

AW-TMP INOP Airway temperature measurement is inoperable. Yes


APNEA CO2 Apnea — no CO2 fluctuation for 30 seconds. Yes

INSP CO2 HI Inspiratory CO2 > high limit. Yes


CO2 ALRM OFF CO2 alarm disabled. No



SPEAKER FAIL Primary speaker failure. Yes


Dräger Cicero EM

PM8060 ERR Hardware problem PM8060. Yes

COOLING PM8060 Check PM8060 cooling. Yes

CAL % O2? Oxygen analyzer not calibrated. No

% O2 $& <21 Inspired oxygen low limit < 21%. No

% O2 ERR Inspired O2 measurement inoperable (alarm). No

FRESH GAS? Check gas supply. Yes


VENT ERR Problems with anesthesia machine. Yes

COM VENT ERR Anesthesia machine communication lost. Yes

EXP-VALVE? Check expiration valve. Yes


APNEA Apnea by different or undefined source. Yes

VOL ERR Flow measurement inoperable. No

FLOW SENSOR? Check flow sensor. No

CHECK PAW Check PAW. No

HRT RATE FLOW Heart rate pulse < low limit. Yes

HRT RATE HI Heart rate > high limit. Yes

ECG ELEC. LL ECG left leg electrode is disconnected. No

ECG ELEC. LA ECG left arm electrode is disconnected. No

ECG ELEC. RA ECG right arm electrode is disconnected. No

ECG ELEC. N ECG neutral arm electrode is disconnected. No

NO S-T ECG S-T analysis impossible. No

ECG ELECTROD ECG electrode disconnected. No

S-T MV”# S-T segment-level deviation > limit. No

ASYSTOLY Asystole for 6 seconds. Yes

ECG ELEC. V ECG lead V disconnected. No




Dräger Cicero EM

ECG SMALL ECG signal too small. No

VENTR. FIBR. ECG ventricular fibrillation. Yes

PULSE DEFIC. Pulse deficit > high limit. No

NO IBP PULSE No invasive pulse for 20 seconds. No

SYS IBP1 LOW Invasive systolic 1 < low limit. No

SYS IBP1 HI Invasive systolic 1 > high limit. No

IBP1PULSE HI Invasive pulse 1 > high limit. No

CHECK IBP1 Check IBP1 sensor. No

IBP1PULSELO Invasive pulse 1 < low limit. No

NO IBP1 PULS No invasive 1 pulse. No

MEAN IBP1 LO Invasive mean 1 < low limit. No

MEAN IBP1 HI Invasive mean 1 > high limit. No

DIAS IBP1 LO Invasive diastolic 1 < low limit. No

DIAS IBP1 HI Invasive diastolic 1 > high limit. No

SYS IBP2 LOW Invasive systolic 2 < low limit. No

SYS IBP2 HI Invasive systolic 2 > high limit. No

IBP2PULSEHI Invasive pulse 2 > high limit. No

CHECK IBP2 Check IBP2 sensor. No

MEAN IBP2 LO Invasive mean 2 < low limit. No

MEAN IBP 2 HI Invasive mean 2 > high limit. No

IBP2PULSEHI Invasive pulse 2 > high limit. No

IBP2PULSELO Invasive pulse 2 < low limit. No

NO IBP2PULS No invasive 2 pulse. No

DIAS IBP2 LO Invasive diastolic 2 < low limit. No

DIAS IBP2 HI Invasive diastolic 2 > high limit. No

P-BOX ALAR OF Parameter-Box alarms disabled. No




Dräger Cicero EM

WATER TRAP? Check watertrap. No

NIBP SYS LOW NIBP systolic < low limit. No

NIBP DIAS LOW NIBP diastolic < low limit. No

NIBP SYS HI NIBP systolic > high limit. No

NIBP DIA HI NIBP diastolic > high limit. No

NO NIBP PULS No NIBP pulse. No

NIBP MEAN LO MIBP mean < low limit. No

NIBP MEAN HI NIBP mean > high limit. No

BP CUFF ERR NIBP cuff is improperly placed. No

BP CURR DISC NIBP cuff is disconnected or leaking. No

NIBP ALRM OF NIBP alarm is disabled. No

NIBP ERR NIBP device failure. No

NIBP MOTIONS NIBP motions detected. No

TEMP 1 LOW Temperature 1 < low limit. No

TEMP 2 LOW Temperature 2 < low limit. No

TMP 1 NOT CAL Temperature 1 is not calibrated or poorly calibrated. No

TMP 2 NOT CAL Temperature 2 is not calibrated or poorly calibrated. No

TEMP 1 ERR Temperature 1 probe is disconnected or fault. No

TEMP 2 ERR Temperature 2 probe is disconnected or fault. No

TEMP 1 HIGH Temperature1 > high limit. No

TEMP 2 HIGH Temperature 2 > high limit. No





Dräger Evita II, Evita II Dura, and Babylog 8000


VENT - MAIN MENUALARM LIMITS SETUP*


VIEW ALARMS PRINT

SMALL TXT

VENT - SETUP

SET 1 SET 2 SET 3 SAVE SET

VENT - ALARM LIMITS

VMIN VE* ETCO2* f-spo**Available on Evita II and Evita II Dura only.

VENT - ALARM LIMITS - f-spof-spo HI =

XXf-spo

ON OFF VE

VENT - ALARM LIMITS - EtCO2ETCO2 HI =

XX.XLO = XX.X

ETCO2ON OFF f-spo

VENT - ALARM LIMITS - VEVE HI =

X.XLO = X.X

VEON OFF ETCO2

VENT - ALARM LIMITS - VMINVMIN HI =

X.XXLO = X.XX ↑ ↓

ON OFF


Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
OverviewThe 90436A-10B Flexport system interface enables information from a Dräger Babylog 8000 ventilator to be displayed on Spacelabs Healthcare monitors.

The 90436A-10E Flexport system interface enables information from a Dräger Evita II and the Evita II Dura ventilators to be displayed on Spacelabs Healthcare monitors.

Note:This interface does not apply to the Evita IV ventilator. In this document, all references to the Evita II apply to both the Evita II and the Evita II Dura.


Note:To start communication with the Flexport system interface connected to the Babylog, select BabyLink from the Special Functions/Print menu and select EVEN from the Special Functions/Configuration/Com menu.


Baud Rate

Character Length

Parity Setting

Stop Bit



Part Number

9600 8 bit even 1 3.00 131-0686-xx





Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the ventilator (depending on the ventilator model and the settings chosen).

Evita II — Set 1





• Plug the other end of the cable into the transition connector.• Plug the transition connector into the RS-232 connector on the ventilator.

� � � � � �

22 MAP 19 FiO2 0.09 VT VENT

23PIP

mbar % L mbar

16 EtCO2 5.0EtCO2

21 f2.1

VE

L/minmbar % BPM

� �





� Mean airway pressure value

� Fraction inspired O2 value

� Tidal volume value




� Expiratory minute volume value

Respiratory frequency value

End tidal CO2 value

� Positive end expiratory pressure value

� � � �

VENT

VT = 0.09LVE = 2.1L/minPIP = 23mbar VENT

ALMOFF

EtCO2 = 5.0%

� � � � � �

EtCO2=5% PIP=23mbar VENT

� FiO2=19% PEEP=16mbar

� MAP=22mbar VT=0.09L

f=21BPM VE=2.1L/min



Evita II — Set 2




� Resistance value

� Intrinsic positive end expiratory pressure value


� Spontaneous minute volume value


� � � � �

11 R 0 iPEEP VENT

00.5MVspo

mbar/L/s mbar L/min

13 C 0.0 OccPrs 10 Pmin36

f-spo

BPML/bar mbar mbar

� �

� � �

VENT

MVspo=00.5L/minR=11mbar/L/sC=13L/bar VENT

ALMOFF

f-spo=36BPM

�

� R=11mbar/L/s MVspo=00.5L/min VENT

C=13L/bar Pmin=10mbar

� iPEEP=0mbar f-spo=36BPM

OccPrs=0.0mbar

� � � �



� Spontaneous respiratory frequency value

� Minimal airway pressure value

Occlusion pressure value

Compliance value

Evita II — Set 3



� � � �

0 VCO2 VENT

22Pplat

ml/min mbar

25 Vds 10T

Cml

� �

� �

VENT

VCO2 = 0ml/minVds = 25ml �Pplat = 22mbar VENT

ALMOFF

T = 10C

� �




� CO2 production value


� Plateau pressure value


� Airway temperature value

� Dead space value

Babylog 8000



�

� VCO2=0ml/min VENT

� Vds=25ml

� pPlat=22mbar

� T=10C

� � � � � �

23PIP 18 MAP 0 SpVmin

VENT

0.63Vmin

mbar mbar % L

21FiO2

16PEEP

0LEAK 38

RR

% mbar % BPM

� �

� �

VENT

Vmin = 0.63 LRR = 38 BPM �PIP = 23 mbar VENT

ALMOFF

FiO2 = 21%

� �






� Spontaneous fraction minute volume value


� Respiratory minute volume value


� Spontaneous respiratory rate value

Leakage value

Positive end expiratory pressure value








Alarms settings default to OFF.

Note:• Turning Flexport system interface alarms ON or OFF does not affect alarms settings on the ventilator.

• The Evita II alarm limits can only be adjusted at the Evita II. Alarm violation is detected at the ventilator and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• The Babylog 8000 alarm limits are adjustable at the Flexport system interface.


� � � �

� PIP = 23 mbar MAP = 18 mbar VENT

FPEEP = 16 mbar Vmin = 0.63L

� FiO2 = 21% SpVmin = 0%

� RR = 38BPM VLEAK = 0%

�



Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the ventilator’s parameters (refer to Figure 22-13 and Figure 22-14). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays VENT ALM OFF to the right of the VENT key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.

Figure 22-13: View Alarms screen (Evita II)

Figure 22-14: View Alarms screen (Babylog 8000)


• Touch VENT.• Touch ALARM LIMITS.• Select alarm parameter.• Touch the parameter alarm ON/OFF key.To adjust alarm limits for the Babylog 8000:• Select HI= or LO=.• Use arrow keys to adjust.



EtCO2 6.0 f-spo 60 VENT

23PIP

0.0 mbar

VE 5.0 2.1VE

0.0 L/min

Vmin 1.00 VENT

1.00Vmin

0.10 L

20RR

BPM



Viewing StatusThe VIEW STATUS key enables you to display the recent status messages sent by the ventilator. A maximum of four messages can be simultaneously displayed on the bedside monitor, and three messages can be simultaneously displayed on the remote monitor (refer to Status Messages on page 22-12).
















Table 2 lists the status messages that the Flexport system interface reports for the Evita II ventilator. Messages marked with an “†” are also available for the Babylog 8000.



COMMUNICATION LINK LOST†


AIR SUPPLY? Check air supply. Yes

VOLUME INCONST Volume not constant. Yes

ASB>4sec Assisted spontaneous breathing > 4 seconds Yes

CO2 NOT CAL CO2 not calibrated. Yes

TACHYPN’@OFF Tachy/apnea alarm disabled. No

FLOW SENSOR? Check flow sensor. Yes


VOL ALRM OFF Volume alarm disabled. No


CLEAN CO2 CO2 window occluded. Yes

CO2 Err CO2 device failure. Yes

RS232 INOP RS232 PORT. Yes

APNEA EVITA Apnea detected by Evita. Yes

PAW LOW Disconnection ventilator. Yes

EVITA ERR Problems with respirator (Evita). Yes

%O2 ERR† O2 measurement inoperable. Yes

Vol Err† Volume measurement inoperable. Yes

MV ALRM OFF MIN VOL alarm disabled. No




EXP-VALUE? Check expiration value. Yes

COOLING INOP Too high respirator device temperature. Yes

AW-TEMP INOP Airway temp measurement inoperable. Yes

AW-TEMP SENS Check airway temp sensor. Yes


SYSTEM OPEN Breathing system vented. No

%O2 HIGH % Oxygen > high limit. Yes

%O2 LOW % Oxygen < low limit. Yes

MIXER INOP Gas mixer inoperable. Yes

TIME LIMITED Time limited respiratory volume. No


COOLING INOP High respirator device temperature. Yes

SYNCHRO INOP Respirator synchronization inoperable. Yes

CYCLE FAILED Fail to cycle. Yes

CO2 SENS? CO2 sensor disconnected or fault. Yes





Dräger Evita 4


VENT - MAIN MENUALARM LIMITS SETUP


VIEW ALARMS PRINT

SMALL TXT

VENT - SETUP


VENT - ALARM LIMITS

MV ETCO2 f-spn

VENT - ALARM LIMITS - f-spnf-spn HI =

XXf-spn

ON OFF MV


XX.XLO = XX.X

ETCO2ON OFF f-spn

VENT - ALARM LIMITS - MVMV HI =

X.XLO = X.X

MVON OFF ETCO2

Dräger Evita 4

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OverviewThe 90436A-16 Flexport system interface enables information from a Dräger Evita 4 ventilator to be displayed on Spacelabs Healthcare monitors.





Baud Rate

Character Length

Parity Setting

Stop Bit



Part Number

9600 8 bit even 1 3.00 131-0686-xx



interface.• Plug the other end of the cable into the transition connector.• Plug the transition connector into the RS-232 connector on the ventilator.


Dräger Evita 4

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the ventilator. EtCO2 units of measure are determined by the ventilator configuration. They may display as percentages (refer to Figure 23-1), mmHg, or kPa. Pressures display as mbar, and temperatures display as ° C.

Evita 4 — Set 1




� � � � � �

22Pmean 19 FiO2 0.09 VTe

VENT

23Ppeak

mbar % L mbar

16PEEP

5.0EtCO2

21f 2.1

MV

mbar % BPM L/min

� �

� � � �

VENT

VT = 0.09LMV = 2.1L/minPpeak = 23mbar VENT

ALMOFF

EtCO2 = 5.0%

� � � � �

EtCO2=5% Ppeak=23mbar VENT


� Pmean=22mbar VTe=0.09L

f=21BPM MV=2.1L/min

�


Dräger Evita 4



� Expiratory tidal volume value






End tidal CO2 value


Evita 4 — Set 2



� � � � �

11 R 0 PEEPi VENT

00.5 MVspn

mbar/L/s mbar L/min

13 C 0.0 PO.1 10 Pmin 36 f-spn

L/bar mbar mbar BPM

� �

� �

VENT

MVspn=00.5L/minR=11mbar/L/s �C=13L/bar VENT

ALMOFF

f-spn=36BPM

�


Dräger Evita 4


� resistance value

� intrinsic positive end expiratory pressure value


� spontaneous breathed minute volume value

� alarm status bell (appears when alarms are turned ON)

� spontaneous respiratory portion of overall frequency value

� minimal airway pressure value

occlusion pressure value within 100 ms

compliance value

� R=11mbar/L/s MVspn=00.5L/min VENT


� PEEPi=0mbar f-spn=36BPM

� PO.1=0.0mbar

� � � �


Dräger Evita 4

Evita 4 — Set 3






� End inspiratory airway pressure


� Inspiratory breathing gas temperature value

� Serial dead space value

� � � �

0 VCO2 VENT

22 Pplat

ml/min mbar

25 Vds 10 T

ml C

� �

� �

VENT


ALMOFF

T = 10C

� �


� Vds=25ml

� Pplat=22mbar

� T=10C

�


Dräger Evita 4









• The Evita 4 alarm limits can only be adjusted at the Evita 4. Alarm violation is detected at the ventilator and the Flexport system interface reports the alarm if it is turned ON for that parameter.


To turn alarms ON/OFF for the Spacelabs Healthcare monitor:

• Touch VENT.• Touch ALARM LIMITS.• Select alarm parameter.• Touch the parameter alarm ON/OFF key.


Dräger Evita 4

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the ventilator’s parameters (refer to Figure 23-10). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays VENT ALM OFF to the right of the VENT key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.

Figure 23-10: View Alarms screen (Evita 4)






EtCO2 6.0 f-spn 60 VENT

23Ppeak

0.0 mbar

MV 5.0 2.1MV

0.0 L/min


Dräger Evita 4










Dräger Evita 4




Table 2 lists the status messages that the Flexport system interface reports for the Evita 4 ventilator.






ASB>4sec Assisted spontaneous breathing > 4 seconds. Yes






CO2 WARM UP CO2 monitor in low accuracy mode (warm-up). No



RS232 INOP RS232 PORT. Yes


PAW HIGH Airway pressure > high limit. Yes

PAW LOW Disconnection ventilator. Yes


%O2 ERR O2 measurement inoperable. Yes

Vol Err Volume measurement inoperable. Yes


Dräger Evita 4











TIDVOL HIGH Tidal volume > high limit. Yes












Dräger Evita 4/XL

Directory of Keys

VENT

VENT - MAIN MENU

ALARM LIMITS SETUP


VIEW ALARMS PRINT

SMALL TXT

VENT - SETUP


VENT - ALARM LIMITS

MV ETCO2 f-spn

VENT - ALARM LIMITS - f-spnf-spn HI =

XXf-spn

ON OFF MV


XX.XLO = XX.X

ETCO2

ON OFF f-spn

VENT - ALARM LIMITS - MVMV HI =

X.XLO = X.X

MV

ON OFF ETCO2

Dräger Evita 4/XL

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OverviewThe 90436A-16 Flexport system interface enables information from a Dräger Evita 4 or Evita XL ventilator to be displayed on Spacelabs Healthcare monitors.



Baud Rate

Character Length

Parity Setting

Stop Bit



Part Number

9600 8 bit even 1 3.00 131-0686-xx


Dräger Evita 4/XL



Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the ventilator. EtCO2 units of measure are determined by the ventilator configuration. They may display as percentages (refer to Figure 24-1), mmHg, or kPa. Pressures display as mbar, and temperatures display as ° C.

Evita 4/XL — Set 1




interface.• Plug the other end of the cable into the transition connector.• Plug the transition connector into the RS-232 connector on the ventilator.• Connect the SDLC cable to the Ultraview monitor/housing.

� � � � � �

22 Pmean 19 FiO2 0.09 VTe VENT

23 Ppeak

mbar % L mbar

16 PEEP 5.0 EtCO2 21 f 2.1 MV

mbar % BPM L/min

� �


Dräger Evita 4/XL





� Expiratory tidal volume value






End tidal CO2 value


� � � �

VENT

VT = 0.09LMV = 2.1L/minPpeak = 23mbar VENT

ALMOFF

EtCO2 = 5.0%

� � � � �

EtCO2=5% Ppeak=23mbar VENT


� Pmean=22mbar VTe=0.09L

f=21BPM MV=2.1L/min

�


Dräger Evita 4/XL





� Resistance value

� Intrinsic positive end expiratory pressure value


� Spontaneous breathed minute volume value


� Spontaneous respiratory portion of overall frequency value

� � � � �

11 R 0 PEEPi VENT

00.5 MVspn

mbar/L/s mbar L/min

13 C 0.0 PO.1 10 Pmin 36 f-spn

L/bar mbar mbar BPM

� �

� �

VENT

MVspn=00.5L/minR=11mbar/L/s �C=13L/bar VENT

ALMOFF

f-spn=36BPM

�

� R=11mbar/L/s MVspn=00.5L/min VENT


� PEEPi=0mbar f-spn=36BPM

PO.1=0.0mbar

� � � �


Dräger Evita 4/XL

� Minimal airway pressure value

Occlusion pressure value within 100 ms

Compliance value







� End inspiratory airway pressure

� � � �

0 VCO2 VENT

22 Pplat

ml/min mbar

25 Vds 10 T

ml C

� �

� �

VENT


ALMOFF

T = 10C

� �


� Vds=25ml

� Pplat=22mbar

� T=10C

�


Dräger Evita 4/XL


� Inspiratory breathing gas temperature value

� Serial dead space value









• The Evita 4 and Evita XL alarm limits can only be adjusted at the Evita 4/XL. Alarm violation is detected at the ventilator and the Flexport system interface reports the alarm if it is turned ON for that parameter.


To turn alarms ON/OFF for the Spacelabs Healthcare monitor:

• Touch VENT.• Touch ALARM LIMITS.• Select alarm parameter.• Touch the parameter alarm ON/OFF key.


Dräger Evita 4/XL








EtCO2 6.0 f-spn 60 VENT

23Ppeak

0.0 mbar

MV 5.0 2.1MV

0.0 L/min


Dräger Evita 4/XL










Dräger Evita 4/XL




Table 2 lists the status messages that the Flexport system interface reports for the Evita 4 or Evita XL ventilator.






ASB>4sec Assisted spontaneous breathing > 4 seconds. Yes






CO2 WARM UP CO2 monitor in low accuracy mode (warm-up). No




PAW HIGH Airway pressure > high limit. Yes

PAW LOW Ventilator disconnection. Yes


%O2 ERR O2 measurement inoperable. Yes

Vol Err Volume measurement inoperable. Yes



Dräger Evita 4/XL










TIDVOL HIGH Tidal volume > high limit. Yes












Dräger Irisa/Evita

Directory of Keys

VENT

Note: The grayed keys are not function keys and are only used to display clinical data. (This data display is delayed for one or two breaths.)

VENT - MAIN MENUALARM LIMITS SETUP MECHANICS MODE

CMV*VIEW

ALARMS PRINT

*This could also be: CMV/A, S/MV, V/MV/PS, SPONT, PS, CPAP, CPAP/PS, MMV, MMV/PS,

APRV, MASTER, SLAVE, AP VENT, or UNKNOWN MODE

LARGE TXT

SMALL TXT

VENT - C in ml/cmH2O VENT - R in cmH2O/L/SC = XXX R = XXX

VENT - ALARM LIMITS

VMIN PIP

VENT - ALARM LIMITS - PIPPIP

ON OFF

VENT - ALARM LIMITS - VMINVMIN

ON OFF

Dräger Irisa/Evita

Contents
OverviewThe 90436A-09 Flexport system interface enables information from a Dräger Irisa/Evita ventilator to be displayed on Spacelabs Healthcare monitors.

Configure the ventilator as shown in Table 1. Consult the appropriate ventilator manual for additional configuration setup procedures.



Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number


1200 7-bit even 2 131-0697-xx (25-pin)

9.0, 9.5, 9.6 (Irisa)9.07 (Evita)




• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector of the ventilator.


Dräger Irisa/Evita






� Measured peak inspiratory pressure

� Fractional-inspired O2 value

� � � � �

30 PIP 20 FiO2 4.1 Vmin VENT

0.40 Vt

cmH2O % L L

1 PEEP 29 PLT 9 MAP 10 RR

cmH2O cmH2O cmH2O BPM

� � �

� �

VENT

VT = 0.40 LRR = 10 BPM �PIP = 30 cmH2O �PEEP = 1 cmH2O

� �

� � �

� RR = 10BPM FiO2 = 20%VENT

MAP = 9cmH2O PIP = 30cmH2O

� VT = 0.40L PLT = 29cmH2O

� VMIN = 4.1L PEEP = 1 cmH2O

� ICU 14

� �


Dräger Irisa/Evita

� Measured minute volume

� Measured positive end expiratory pressure

� Measured inspiratory plateau pressure



Measured tidal volume

Measured respiratory rate


� Patient/room ID






When all parameter alarms are turned OFF, status alarms still cause the VENT key to flash.





• Touch VENT.• Select ALARM ON/OFF.• Select an alarm parameter.• Select the parameter alarm ON/OFF key.


Dräger Irisa/Evita








• Touch VENT.• Touch SETUP.• Touch LARGE TXT or SMALL TXT.

VENT

VT = 0.40 LVMIN FIO2 PIP RR = 10 BPM

PIP = 30 cmH2O

PEEP = 1 cmH2O

ICU 14


Dräger Irisa/Evita













SERVICE NEEDED Contact Dräger Irisa service representative. No

COMPRESSES AIR LOW Compressed air supply less than 36 psi. No

O2 PRESSURE LOW Oxygen supply less than 36 psi. No

PRESSURE MEAS INOP Pressure sensor defective. No

O2 MEAS INOP O2 sensor defective. No

FLOW MEAS INOP Flow sensor defective. No

MIXER INOP HPSV defective. No

EXP VALVE INOP Flow in expiratory line during inspiratory phase. No


Dräger Irisa/Evita

FAN DEFECT Contact Dräger Irisa service representative. No

TEMPERATURE MEAS INOP Temperature sensor defective. No

TEMPERATURE SENSOR? Temperature sensor was disconnected while machine was turned ON. No

TEMPERATURE HIGH Inspiratory gas temperature less than 40 ºC. No

APNEA OR FAIL TO CYCLE

Leak in the breathing system.Loss of volume due to pressure or time limitation.Spirolog is not calibrated.Machine malfunction; call biomed.

Yes

HIGH RATE Patient’s respiratory rate exceeds the respiratory rate limit. Yes

SYNCHRONIZATION INOP Contact Dräger Irisa service representative. Yes

PRESSURE LIMITED Set pressure control limit exceeded. Yes




Dräger Narkomed 2B and 2C



FREEZE * VIEW STATUS

VIEW ALARMS PRINT

ON OFF

VENT - SETUP *Narkomed 2C only.

SIZE* SWEEP

SPEED*

WAVEFORM* LARGE TXT

SMALL TXT

VENT - SETUP - WAVEFORM TYPE

FLOW PRESSURE

VENT - SETUP - SWEEP SPEED25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec

VENT - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF

VENT - ALARM LIMITS

FiO2 PIP Vmin


XXXLO = XXX

FiO2ON OFF Vmin


XXXLO = XXX

PIPON OFF Vmin


XXXLO = XXX

FiO2ON OFF PIP



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Freezing the Waveform on the Display (Narkomed 2C Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
OverviewThe 90436A-11 Flexport system interface enables information from the Dräger Narkomed 2B and 2C ventilators to be displayed on Spacelabs Healthcare monitors.

Configure the ventilator as shown in Table 1. In the ventilator’s Serial Port Configuration menu, choose VITALINK as the Protocol selection. Consult the ventilator manual for additional configuration setup procedures.



Character Length


Minimum Vitalink Protocol

Narkomed 2C 9,600 8 bit Even 1 1.20

Narkomed 2B 1,200 8 bit Even 1 1.15






Figure 26-1: Bedside monitor, large text screen (Narkomed 2C)




• Plug the other end of the modular cable into the transition connector (P/N 131-1039-00).

• Plug the transition connector into the RS-232 connector on the ventilator.

� � � � � �

7MAWP 19 PIP 27 FiO2 V

ENT

0.25Vtexp

WAVE=FLOW

cmH2O cmH2O % L

3 PEEP 1.3 Vmin 36 RR

cmH2O L BPM

� �



Figure 26-2: Bedside monitor, small text screen (Narkomed 2C)

Figure 26-3: Central monitor, split screen (Narkomed 2C)






� Current waveform mode


Respiratory rate value

Minute volume value


� Patient/room ID

� � � �

VENT

FiO2= 27% WAVE=FLOWPIP= 19cmH2O

Vmin= 1.3LRR= 36BPM

�

� � � � �

RR=36BPM PIP=19cmH2OVENT

� FiO2=27% PEEP= 3cmH2O

Vmin=1.3L MAWP=7cmH2O

� Vtexp=0.25L

� ICU 14














• Touch VENT.• Touch ALARMS LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.



Viewing Alarm SettingsThe VIEW ALARM key enables you to display the current alarm settings for all parameters (refer to Figure 26-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays VENT ALM OFF to the right of the VENT key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.

Figure 26-4: View Alarms screen (Narkomed 2C)






PIP 50 FiO2 70 VENT

1.62 Vtexp WAVE=FLOW30 L

Vmin 90 RR

0.1 BPM




Turning Waveforms ON or OFF (Narkomed 2C Only)You can turn waveforms OFF and display only the numeric values. When waveforms are OFF, the SWEEP SPEED key, the FREEZE ON/OFF keys, and the SIZE ↑ and SIZE ↓ keys are disabled.


Adjusting the Waveform Size (Narkomed 2C Only)If the waveform is too large to fit within the display zone, use the waveform size keys to adjust the display size.



• Touch VENT.• Touch SETUP.• Touch SIZE.• Select WAVEFORM ON/OFF.


• Touch VENT.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.



Selecting a Sweep Speed (Narkomed 2C Only)The sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 25, 12.5, 6.25, and 3.12 mm/second.


Selecting a Waveform Type (Narkomed 2C Only)You can select either FLOW or PRESSURE waveforms for display.



• Touch VENT.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.


• Touch VENT.• Touch SETUP.• Touch WAVEFORM.• Select FLOW or PRESSURE waveform display.


• Touch VENT.• Touch SETUP.• Select LARGE TXT or SMALL TXT.



Freezing the Waveform on the Display (Narkomed 2C Only)The FREEZE ON key enables you to freeze the waveform on the display. When you freeze the waveform, the Flexport system interface continues to process and update the numeric information.




printout.

• The PRINT key does not print the waveform. A waveform recording on the Narkomed 2C is obtained by touching the monitor RECORD key.




The Flexport system interface reports approximately 250 status messages for the ventilator during Flexport system interface operation, depending on the configuration of the ventilator and components on the Dräger Vitalink bus. Refer to your ventilator manual for the cause of the status messages and appropriate action.


• Touch VENT.• Touch FREEZE ON.




Dräger Narkomed 3, 4, and GS



FREEZE VIEW STATUS

VIEW ALARMS PRINT

ON OFFRefer to

page 27-2

ANES - SETUP

SIZE SWEEP SPEED WAVEFORM

LARGE TXTSMALL TXT

ANES - SETUP - WAVEFORM TYPE

CO2 FLOW PRESSURE


mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec0.78

mm/sec0.39

mm/sec


↑SIZE

↓ON OFF



ANES


FREEZE VIEW STATUS

VIEW ALARMS PRINT

ON OFFRefer to

page 27-1

ANES - ALARM LIMITS

ETCO2 SpO2 SYS I AGT FiO2 PIP Vmin

ANES - ALARM LIMITS - VminVmin HI =

XX.XLO = XX.X

ETCO2ON OFF Vmin

ANES - ALARM LIMITS - PIPPIP HI =

XXXLO = XXX

PIPON OFF Vmin

ANES - ALARM LIMITS - FiO2FiO2 HI =

XXXLO = XXX

FiO2ON OFF PIP

ANES - ALARM LIMITS - I AGTI AGT HI =

X.XXLO = X.XX

I AGTON OFF FiO2

ANES - ALARM LIMITS - SYSSYS HI =

XXXLO = XXX

SYSON OFF I AGT

ANES - ALARM LIMITS - SpO2SPO2 HI =

XXXLO = XXX

SpO2ON OFF SYS

ANES - ALARM LIMITS - ETCO2ETCO2 HI =

XXLO = XX

ETCO2ON OFF SPO2



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
OverviewThe 90443A-02 Flexport system interface enables information from a Dräger Narkomed 3, 4, or GS anesthesia machine to be displayed on Spacelabs Healthcare monitors.

Configure the anesthesia machine as shown in Table 1. Consult the appropriate anesthesia machine manual for additional configuration setup procedures.


Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number

Minimum Vitalink Protocol

9600 8-bit none 1131-1039-xx

(9-pin)1.15










• Plug the other end of the cable into the transition connector.• Plug the transition connector into the RS-232 connector on the anesthesia machine.

� � � � � �

96 SPO2 27 PIP 0.90 I AGT ANES

162SYS WAVE=

CO2

% cmH2O % mmHg

35 ETCO2 12.7 Vmin 59 FiO2 90 DIA

mmHg L % mmHg

� � �





� Pulse oximetry value

� Measured inspiratory plateau pressure

� Inspired agent


� Systolic blood pressure

� Current waveform type (Narkomed 4 only)


Diastolic blood pressure

Measured inspired oxygen level

� Minute volume

� Current end tidal CO2 (mmHg) value

Patient/room ID

� � �

ANES

SYS = 162 mmHg WAVE=FLOWDIA = 90 mmHg

SPO2 = 96 % �RR= 36BPMETCO2 = 35 mmHg

� �

� �

� ETCO2= 35 mmHg SYS= 162 mmHg ANES

� SPO2= 96 % DIA= 90 mmHg

FiO2= 59 % I AGT= 0.90 %

� Vmin= 12.7 L PIP= 27 cmH2O

ICU 14

� � �











machine.

• Alarm limits can only be adjusted at the anesthesia machine. Alarm violation is detected at the anesthesia machine, and the Flexport system interface reports the alarm if it is turned ON for that parameter.






Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the anesthesia machine’s parameters. If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays ANES ALM OFF to the right of the ANES key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.


Viewing StatusThe VIEW STATUS key enables you to display the recent status messages sent by the anesthesia machine. A maximum of four messages can be simultaneously displayed on the bedside monitor, and three messages can be simultaneously displayed on the remote monitor (refer to Status Messages on page 27-10).



To view the anesthesia machine status:


I AGT4.09

ETCO245

SYS180 A

NES

162 SYS WAVE=CO2

0.00 25 85 mmHg

SPO2 100 PIP 50 Vmin FiO2 90 DIA

95 2.7 mmHg






Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 0.39, 0.78, 1.56, 3.12, 6.25, 12.5, and 25 mm/second.








Selecting a Waveform Type (Narkomed 4 Only)You can select CO2, FLOW, or PRESSURE waveforms for display.




To select a waveform type for Narkomed 4 only:

• Touch ANES.• Touch SETUP.• Touch WAVEFORM.• Select CO2, FLOW, or PRESSURE waveform display.



To freeze the waveform display:






printout.









Edwards Vigilance I

Directory of Keys

CO

CO - MAIN MENUALARM LIMITS SETUP SEND

CCOVIEW

ALARMS PRINT

CO - SETUPLARGE TXT

SMALL TXT

CO - ALARM LIMITS

SvO2 CCO CCI

CO - ALARM LIMITS - CCICCI HI =

XXLO=XXON OFF

CO - ALARM LIMITS - CCOCCO HI =

XXLO=XXON OFF

CO - ALARM LIMITS - SvO2SvO2 HI =

XXLO=XXON OFF


Edwards Vigilance I

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Storing a CCO Value as a Bolus CO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OverviewThe 90442A Flexport system interface enables information from a Baxter-Edwards Critical Care Division Vigilance I continuous cardiac output (CCO) monitor to be displayed on Spacelabs Healthcare monitors.

Configure the CCO monitor as shown in Table 1. Complete the steps in the following Quickstart to select the communication port and the Flexport system interface from the CCO monitor. Consult the manufacturer’s manual for additional configuration setup procedures.

To select the Flexport system interface from the CCO monitor:

• Power ON the CCO monitor.• Touch SETUP.• Touch SYSTEM CONFIG.• Touch DIGITAL PORTS.• Cursor to the device line and select COM1 or COM2.• Touch CHANGE.• Select the Flexport system interface.


Edwards Vigilance I

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the CCO monitor, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the CCO monitor. To control other interface functions, refer to the sections that follow.

Table 1: CCO Monitor Configuration

Monitor Name and Model Number

Baud Rate


Installation Kit

Part Number


Part Number

Baxter Edwards Critical Care Division Vigilance I Monitor VGS (100/115V) 9600 04.42 045-0033-xx 131-1039-xx

Baxter Edwards Critical Care Division Vigilance I Monitor VGS1 (220V) 9600 04.42 045-0034-xx 131-0686-xx*

* P/N 131-0686-xx requires a gender changer.




• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 9-pin connector (COM1 or COM2) on the

CCO monitor.


Edwards Vigilance I

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the CCO monitor.




� Continuous cardiac output value

� Continuous systemic vascular resistance

� Venous O2 saturation


� � � � �

4.8 CCO 1200 SVR 80 SvO2

CO

4.2 CO CALC

%

2.4 2400 37.0 2.1 CI CALCCCI SVRI BT

°C

� � �

� �

CO

SvO2= 80%CCO= 4.8 �CC I = 2.4BT=37.0°C

� �

� �

� CO CALC= 4.2 SVR =1200

CO

� CC I CALC= 2.1 SVRI =2400

� CCO= 4.8 SvO2= 80% �� CC I = 2.4 BT=37.0 °C

� ICU 14 �


Edwards Vigilance I

� Cardiac output CALC value


� Cardiac index CALC value

Blood temperature value

Continuous systemic vascular resistance index

� Continuous cardiac index value

� Patient/room ID






When all parameter alarms are turned OFF, alarm status messages will still cause the CO key to flash.


Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the CCO

monitor.

• Alarm limits can only be adjusted at the CCO monitor. Alarm violation is detected at the CCO monitor, and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• Alarm tones on the CCO monitor can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.


• Touch CO.• Touch ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


Edwards Vigilance I

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the CCO parameters (refer to Figure 28-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays CO ALM OFF to the right of the CO key. If alarms are turned ON for any parameter, a bell displays. The alarm bell flashes when an alarm limit is violated.








SvO29910 CCI

7.01.0

CO

SvO2= 80%

CCO20.01.0 CCO = 4.8

CC I = 2.4BT=37.0°C


Edwards Vigilance I

Storing a CCO Value as a Bolus COEach time the SEND CCO key is touched, the current CCO value is displayed as CO CALC. This CO CALC value is stored in TRENDS and is available for use in the Spacelabs Healthcare monitor’s CALCS package.



To store a CO CALC value:

• Touch CO.• Touch SEND CCO.

To print the CCO monitor display:



Edwards Vigilance I

Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the CCO monitor or the cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the CCO monitor is powered ON.


Table 2 lists the status messages that the Flexport system interface reports for the CCO monitor during Flexport operation.




Communication between the Spacelabs Healthcare monitor and the CCO monitor has been interrupted. Yes

SvO2 PROBLEM — CHECK VIGILANCE

SvO2 catheter is not attached, not calibrated, or is defective. No

CCO PROBLEM — CHECK VIGILANCE

CCO catheter is not attached, is defective, or is not providing data. No



Edwards Vigilance II

Directory of Keys

CO

CO - MAIN MENUALARM LIMITS SETUP SEND

CCOVIEW

ALARMS PRINT

CO - SETUPLARGE TXT

SMALL TXT

CO - ALARM LIMITS

CCO CCI SVR CEDVI SvO2 RVEF

CO - ALARM LIMITS - RVEFRVEF HI =

XXLO=XXON OFF


XXLO=XXON OFF

CO - ALARM LIMITS - CEDVICEDVI HI =

XXLO=XXON OFF

CO - ALARM LIMITS - SVRSVR HI =

XXLO=XXON OFF

CO - ALARM LIMITS - CCICCI HI =

XXLO=XXON OFF

CO - ALARM LIMITS - CCOCCO HI =

XXLO=XXON OFF



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Storing a CCO Value as a Bolus CO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OverviewThe 90442A-03 Flexport system interface enables information from an Edwards Critical Care Division Vigilance II continuous cardiac output (CCO) monitor to be displayed on Spacelabs Healthcare monitors.



• Power ON the CCO monitor.• Select SETUP.• Select SERIAL PORT SETUP.• Select DEVICE for either COM1 or COM2.• Select ‘Flexport’.



Baud Rate


Installation Kit

Part Number


Part Number

Edwards Critical Care Division Vigilance II Monitor VGS (100/115V)

9600 00.56 045-0161-xx 131-0686-xx*

* P/N 131-0686-xx requires a gender changer.










• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 9-pin connector (COM1 or COM2) on the

CCO monitor.

� � � � �

3.9 CCO 1185 SVR 61 SvO2

CO

4.1 CO CALC

%

1.6 37 56 1.7 CI CALCCCI CEDVI RVEF

%

� � �





� Continuous cardiac output value

� Continuous systemic vascular resistance

� Venous O2 saturation


� Cardiac output CALC value


� Cardiac index CALC value

Right ventricular ejection fraction

Continuous end diastolic volume indexed

� Continuous cardiac index value

� Patient/room ID

� �

CO

SvO2 = 61%CCO = 3.9 �CCI = 1.6RVEF = 56%

� �

� �

� CO CALC= 4.1 SVR = 1185

CO

� CI CALC= 1.7 CEDVI = 37

� CCO= 3.9 SvO2 = 61% �� CCI = 1.6 RVEF = 56%

� ICU 14 �








When all parameter alarms are turned OFF, alarm status messages will still cause the CO key to flash.


Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the CCO

monitor.

• Alarm limits can only be adjusted at the CCO monitor. Alarm violation is detected at the CCO monitor, and the Flexport system interface reports the alarm if it is turned ON for that parameter.







Figure 29-4: View Alarms screen, large text

Figure 29-5: View Alarms screen, small text



CCO14.03.0 SVR

1500500 SvO2

9910

CO

4.1 CO CALC

CCI CEDVI RVEF 1.7 CI CALC7.01.0

15060

500

CCO14.0

3.0 SVR1500500 SvO2

9910

CO

SvO2 = 61%CCO = 3.9CCI = 1.6

CCI CEDVI RVEFRVEF = 56%

7.01.0

15060

500





Storing a CCO Value as a Bolus COEach time the SEND CCO key is touched, the current CCO value is displayed as CO CALC. This CO CALC value is stored in TRENDS and is available for use in the Spacelabs Healthcare monitor’s CALCS package.





To store a CO CALC value:

• Touch CO.• Touch SEND CCO.








Table 2 lists the status messages that the Flexport system interface reports for the CCO monitor during Flexport operation.




Communication between the Spacelabs Healthcare monitor and the CCO monitor has been interrupted. Yes

SVO2 PROBLEM — CHECK VIGILANCE

SvO2 catheter is not attached, not calibrated, or is defective. No

CCO PROBLEM — CHECK VIGILANCE II

CCO catheter is not attached, is defective, or is not providing data. No



Edwards Vigileo

Directory of Keys

CO

CO - MENUALARM LIMITS SETUP VIEW

ALARMS PRINT

CO - SETUPLARGE TXT

SMALL TXT

CO - ALARM LIMITS

CO CI ScvO2 -OR- SvO2


XXLO=XXON OFF

CO - ALARM LIMITS - ScvO2ScvO2 HI =

XXLO=XXON OFF

CO - ALARM LIMITS - CICI HI =

XXLO=XXON OFF

CO - ALARM LIMITS - COCO HI =

XXLO=XXON OFF

Edwards Vigileo

Contents
OverviewNote:

The Edwards Vigileo monitor does not support blood temperature TB(CO). This value is obtained from the Vigileo monitor in trends as a zero value, even though it is not supported.

The 90442A-03 Flexport system interface enables information from a Edwards Critical Care Division Vigileo continuous cardiac output (CCO) monitor to be displayed on Spacelabs Healthcare monitors.



• Power ON the CCO monitor.• Select the rectangular box at the bottom of the screen.• Select Serial Port Setup.• Change the device to Flexport.



Baud Rate


Installation Kit

Part Number


Part Number

Edwards Critical Care Division Vigileo Monitor VGS (100/115V) 9600 04.42 045-0034-xx 131-0686-xx


Edwards Vigileo








• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 9-pin connector on the CCO monitor.

� � � � �

2.9 CI 88 SVml/b 1200 SVR

CO

4.2 CO

2 SVV 39 SVI 1943 SVRI 61 ScvO2

% %

� � �


Edwards Vigileo



� Cardiac index

� Stroke volume

� Systemic vascular resistance


� Cardiac output value


� Central venous oxygen saturation (ScvO2) value

Systemic vascular resistance index

Stroke volume index

� Stroke volume variation

� Patient/room ID

� �

CO

CO = 7.1CI = 3.0 �ScvO2 = 62% �SV = 92 ml/b

� �

�

� CO= 7.2 SV = 95 ml/b

CO

� ScvO2= 61% SVI = 40

� CI= 3.0 SVR = 1200 �� SVV = 2% SVRI = 1896

� ICU 14 �


Edwards Vigileo






When all parameter alarms are turned OFF, alarm status messages will still cause the CO key to flash. Alarm settings default to ON.

Note:• Alarms that are generated on the CCO monitor will be displayed on the Spacelabs monitor within

three seconds.

• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the CCO monitor.

• Alarm limits can only be adjusted at the CCO monitor. An alarm violation is detected at the CCO monitor, and the Flexport system interface reports the alarm if it is turned ON for that parameter.





Edwards Vigileo



Selecting a Display FormatTwo display formats are available for the bedside monitor (refer to Display Detail on page 30-4). The default setting is LARGE TXT.





CO 142.0 ScvO2 99

10

CO

6.6 CO

CI 7.01.0

62 ScvO2

%


Edwards Vigileo









Engström EAS 9000



FREEZE VIEW STATUS

VIEW ALARMS PRINT

ON OFF

ANES - SETUP

SIZE SWEEP SPEED WAVEFORM

LARGE TXTSMALL TXT

ANES - SETUP - WAVEFORM

CO2 FLOW PRESSURE


mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec


↑SIZE

↓ON OFF

ANES - ALARM LIMITS

FiO2 PIP FiENF EtCO2

ANES - ALARM LIMITS - EtCO2EtCO2 HI =

X.XXLO = X.XX

EtCO2ON OFF FiO2

ANES - ALARM LIMITS - FiENFFiENF HI =

XXXLO = XXX

FiENFON OFF EtCO2

ANES - ALARM LIMITS - PIPPIP HI =

XXXLO = XXX

PIPON OFF FiENF

ANES - ALARM LIMITS - FiO2FiO2 HI =

XXLO = XX

FiO2ON OFF PIP


Engström EAS 9000

Contents
OverviewThe 90443A-06 Flexport system interface enables information from an Engström EAS 9000 anesthesia machine to be displayed on Spacelabs Healthcare monitors.



Baud Rate

Character Length

Parity Setting

Stop Bit

Modular cable

Interface Cable

Part Number

9600 8-bit even 1 25-pin 012-0512-xx


Engström EAS 9000







• Plug the other end of the modular cable into the RS-232 connector on the anesthesia machine labeled COMPUTER.

• Plug the 25-pin female connector into the ANALOG RECORDER connector on the side of the anesthesia machine.

SDLCcable

SDLCterminator

interfacecable

anesthesia machine

SpacelabsHealthcare

monitor

systemFlexport

interface


Engström EAS 9000





� Fractional inspired agent value can be FiHAL, FiENF, FiISO, FiDES, FiSEV, or FiAGT (if the agent is halothane, enflurane, isoflurane, desflurane, sevoflurane, or no selected agent, respectively)


� Respiration rate


� Expired tidal volume data

� � � � � �

0.89 FiENF 58 PIP 11 RR ANES

0.49 Vt [CO2]% cmH2O BPM L

5.9 FiN2O 9.0 PEEP 4.24 EtCO2 30 FiO2

% cmH2O % %

� � �

� � �

ANES

FiENF=0.89% [CO2]FiO2= 30% Vt= 0.49L �EtCO2=4.24%

�

� � � � � �

� FiENF=0.89% Vt = 0.49L ANES

FiO2=30% RR= 11BPM

EtCO2=4.24% FiN2O= 5.9%

� PIP=58cmH2O PEEP= 9.0cmH2O


Engström EAS 9000



Fractional inspired O2 value

End tidal CO2 value; units may be % or mmHg (selected at Engström unit)

� Positive end expiration pressure setting

� Fractional inspired N2O value









machine.




• Touch ANES.• Touch ALARMS LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


Engström EAS 9000



Viewing StatusThe VIEW STATUS key enables you to display the recent status messages sent by the ventilator. A maximum of four messages can be displayed on the bedside monitor, and three can be displayed on the remote monitor (refer to Status Messages on page 31-11).



To view anesthesia status:


FiENF 2.00 PIP 40 ANES

FiENF=0.89%

0.50 4 FiO2= 30%

Vt= 0.49L

FiO2 45 EtCO2 7.50 EtCO2=4.24%18 2.00


Engström EAS 9000






To turn the waveforms ON or OFF:





Engström EAS 9000


The default sweep speed is 25 mm/second.

Selecting a Waveform TypeYou can select either CO2, FLOW, or PRESSURE waveforms for display.






• Touch ANES.• Touch SETUP.• Touch WAVEFORM.• Select the desired waveform.




Engström EAS 9000

Freezing the Waveform on the DisplayThe FREEZE ON key allows you to freeze the waveform on the display. When you freeze the waveform, the Flexport system interface continues to process, update, and display numeric information.




printout.



• Touch ANES.• Touch FREEZE ON.




Engström EAS 9000






Status Message Indication Alarm Sounds


FLOW SENSOR BAD Fresh gas sensor is faulty. No

VAPORIZER FAULT Vaporizer output is zero. No

ALARM SYS OFF No data comm between ventilator and volume monitor. No

CHECK O2 CONC O2 sensor not calibrated. No

SENSOR FAULT # (1-10) Repair appropriate sensor. No

VENT FAULT # (1-10) Repair ventilator. No

VOL MON FAULT # (1-10) Repair volume monitor. No

CALIB SYSTEM # (1-10) Calibrate the appropriate system. No

MINUTE VOL LOW Alarm is active if expiratory minute volume is low. Yes

MINUTE VOL HIGH Alarm is active if expiratory minute volume is high. Yes

N2O SUPPLY OFF N2O supply pressure is under limit. No

O2 SUPPLY OFF O2 supply pressure is under limit. No

HYPOXIC MIXTURE O2 concentration too low. No

N2O OFF Fresh gas N2O cut off due to hypoxic mixture. No

VAPORIZER HIGH Vaporizer setting is above capacity. No

CO2 NOT DETECT No CO2 is detected in sampling tube. No

PATIENT BAG EMP Preset tidal volume is not being delivered. No

N2O RESTORED Settings have been corrected — N2O restored. No


Engström EAS 9000

ANES LIQUID LOW Anesthestic bottle nearly empty. No

BATTERY POWERED Main wall power is OFF. No

BACKUP BATT LOW Battery not fully charged. No


Status Message Indication Alarm Sounds



GE Ohmeda 5200/5210

Directory of KeysCO2

CO2 - MAIN MENUALARM LIMITS SETUP VIEW

ALARMS PRINT

CO2 - SETUP LARGE TXT PERCENTSMALL TXT mmHg

CO2 - ALARM LIMITS

APNEA RR ETCO2 N2O MINCO2

CO2 - ALARM LIMITS - MINCO2MINCO2 HI =

XX ↑ ↓ETCO2

ON OFF MINCO2

CO2 - ALARM LIMITS - N2ON2O HI =

XXLO = XX ↑ ↓ON OFF

CO2 - ALARM LIMITS - ETCO2ETCO2 HI =

XXLO = XX ↑ ↓

ETCO2ON OFF MINCO2

CO2 - ALARM LIMITS - RRRR HI =

XXLO = XX ↑ ↓

APNEAON OFF RR

CO2 - ALARM LIMITS - APNEAAPNEA APNEA

ON OFF RR

GE Ohmeda 5200/5210

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OverviewThe 90433A-02 Flexport system interface enables information from a GE Ohmeda 5200 or 5210 analyzer to be displayed on Spacelabs Healthcare monitors.





Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number


1200 7-bit odd 1 131-0685-xx (25-pin) 6.0






GE Ohmeda 5200/5210





� Current N2O value (present only when reading exceeds 5% or N2O alarm monitoring is enabled)

� Current minimum CO2 value

� CO2 parameter key

� Current EtCO2 value


� � � �

2 N2O 0.7MINCO2 CO2

5.6 ETCO2

% % %

12 RR

BPM

� �

� � �

CO2

ETCO2 = 5.6%

RR = 12 BPM

MINCO2= 0.7%

N2O = 2%

� � �

� � � �

� ETCO2 = 5.6% N2O = 2%CO2

� RR = 12BPM APNEA = 20s

� MINCO2 = 0.7%

ICU 14


GE Ohmeda 5200/5210



Patient/room ID



• the CO2 key flashes,



When all parameter alarms are turned OFF, alarm status messages will still cause the CO2 key to flash.




• The Apnea alarm limit on the analyzer is fixed at 20 seconds.

• The EtCO2 and minimum CO2 alarm limit ranges depend on the selected unit of measurement.


• Touch CO2.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.

To adjust alarm limits:

• Touch CO2.• Select ALARM LIMITS.• Select an alarm parameter.• Select HI= or LO=.• Use the arrow keys to adjust.


GE Ohmeda 5200/5210

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the analyzer’s parameters (refer to Figure 32-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays CO2 ALM OFF to the right of the CO2 key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.





• Touch CO2.• Touch VIEW ALARMS.


• Touch CO2.• Touch SETUP.• Select LARGE TXT or SMALL TXT.

N2O 80 MINCO2 0.7 ETCO2 CO2

5.6 ETCO2

0 %

APNEA 20 RR 12 RR

BPM


GE Ohmeda 5200/5210

Selecting a Unit of MeasurementExpired CO2 can be displayed in percent (%) or millimeters of mercury (mmHg).

The default setting is PERCENT.



To select a measurement unit:

• Touch CO2.• Touch SETUP.• Select PERCENT or mmHg.

To print the current display:

• Touch CO2.• Touch PRINT.


GE Ohmeda 5200/5210








Communication between the analyzer and the monitor has been interrupted. Yes

OCCLUSION The sample line is blocked — check the sample line for blocking or crimps. No

SERVICE REQUIRED The sensor needs to be calibrated. No

SYSTEM PURGING... The monitor is purging moisture from the sample tube. No



GE Ohmeda 5250

Directory of KeysRGM

RGM - MAIN MENUALARM LIMITS SETUP VIEW

STATUSVIEW

ALARMS PRINT

RGM - SETUP MENULARGE TXT PERCENTSMALL TXT mmHg

RGM - ALARM LIMITS

FiAX FiN2O EtCO2 SpO2 FiO2 HR Vt PIP APNEA

RGM - ALARM LIMITS - APNEAAPNEA HI =

XXAPNEA

ON OFF FiAX

RGM - ALARM LIMITS - PIPPIP HI =

XX.XLO =XX.X

PIPON OFF APNEA

RGM - ALARM LIMITS - VtVt HI =

XX.XLO =XX.X

VtON OFF PIP

RGM - ALARM LIMITS - HRHR HI =

XXXLO =XXX

HRON OFF Vt

RGM - ALARM LIMITS - FiO2FiO2 HI =

XXXLO =XXX

FiO2ON OFF HR

RGM - ALARM LIMITS - SpO2SpO2 HI =

X.XXLO =X.XX

SpO2ON OFF FiO2

RGM - ALARM LIMITS - EtCO2EtCO2 HI =

XXXLO =XXX

EtCO2ON OFF SpO2

RGM - ALARM LIMITS - FiN2OFiN2O HI =

XXXLO =XXX

FiN2OON OFF EtCO2

RGM - ALARM LIMITS - FiAXFiAX HI =

XXLO =XX

FiAXON OFF FiN2O

GE Ohmeda 5250

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OverviewThe 90443A-03 Flexport system interface enables information from a GE Ohmeda 5250 Respiratory Gas Monitor to be displayed on Spacelabs Healthcare monitors.



Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number

1200 7 bit odd 1131-1059-xx

(9-pin)


GE Ohmeda 5250



Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the gas monitor.





• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector on the gas monitor.

� � � � � �

7.0 FiAX

% 3.0 FiCO2

% 21 FiO2

% 77 HR

bpm RGM

3.33 VT

L

SpO2 EtCO2 FIN2O RR PIP

98 2.5 50 20 10% % % BPM cmH2O

� � �


GE Ohmeda 5250



� Current inspired anesthetic agent value (agents include halothane, isoflurane, enflurane, desflurane, or sevoflurane)

� Current fraction inspired CO2 value

� Current fraction inspired O2 value

� Current heart rate

� RGM parameter key

� Current tidal volume value


Current peak inspiratory pressure

Current respiratory rate

� Current inspired nitrous oxide value


Current SpO2 value

� Patient/room ID

� � � �

RGM

FiAX = 7.0%

FiCO2 = 3.0%

SPO2= 98%%

RR = 20BPM

� � � � �

� FiAX= 7% Fin2O= 50%RGM

SPO2= 98% FiO2=21%

RR= 20BPM HR = 77bpm

� Vt= 3.33L EtCO2=2.5%

� ICU 14


GE Ohmeda 5250

Enabling AlarmsThe Alarm Limits menu allows you to enable alarm limits for each parameter (except FiCO2). When an alarm is turned ON and that parameter value exceeds an alarm limit, all of the following occur:


• the RGM key flashes,



Alarm limits for anesthetic agents are set at the gas monitor. When an agent parameter value exceeds an alarm limit, the monitor sends alarm data to the recorder.

When all parameter alarms are turned OFF, RGM status alarms do not cause the RGM key to flash. In particular, when the Apnea alarm is OFF and CO2 apnea occurs, the status message is displayed but does not initiate a flashing of the RGM key.


Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the gas monitor.

• Alarm limits can only be adjusted at the gas monitor. Alarm violation is detected at the gas monitor, and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• Alarm tones on the gas monitor can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.


• Touch RGM.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


GE Ohmeda 5250

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the gas monitor’s parameters (refer to Figure 33-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays RGM ALM OFF to the right of the RGM key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.


Viewing StatusThe VIEW STATUS key enables you to display the recent status messages sent by the gas monitor. A maximum of three messages appear on any monitor. When more than three messages are received from the gas monitor, they appear according to a prioritized order (refer to Status Messages on page 33-9).

FiAX 8.0 FiO2 34 HR 150 Vt 1.10RGM

FiAX=7.0%6.6 18 121 0.86 FiCO2=3.0%

SPO2=98%

SpO2 80 EtCO2 9.3 FiN2O 80 Apnea 20 PIP 80 RR=20BPM?? 8.9 ?? ??


• Touch RGM.• Touch VIEW ALARMS.

To view status:

• Touch RGM.• Touch VIEW STATUS.


GE Ohmeda 5250



Selecting a Unit of MeasurementThe units of measurement can be toggled between percent (%) and millimeters of mercury (mmHg), or between percent (%) and kilo Pascals (kPa), depending on the bedside monitor setup.

Warning:When using this product on a network, make sure all monitors viewing this channel are set up for the same units.


• Touch RGM.• Touch SETUP.• Select LARGE TXT or SMALL TXT.


• Touch RGM.• Touch SETUP.• Select PERCENT or mmHg.


GE Ohmeda 5250



Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the gas monitor or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the gas monitor is powered ON.


Table 2 lists some of the other status messages that the Flexport system interface reports for the gas monitor during Flexport system interface operation.


• Touch RGM.• Touch PRINT.



COMMUNICATION LINK LOSTCommunication between the respiratory gas monitor and the Spacelabs Healthcare monitor has been interrupted.

Yes

CO2 APNEA The apnea alarm limit has been violated. No

HIGH SUSTAINED PAW The high-sustained PAW alarm limit has been violated. No

SUB-ATMOSPHERIC PAW The sub-atmospheric alarm limit has been violated. No

LOW CIRCUIT O2 The low circuit alarm limit has been violated. No

HIGH FICO2 The high FiCO2 alarm limit has been violated. No

LOW EXPIRED AGENT The low expired agent alarm limit has been violated. No


GE Ohmeda 5250

HIGH EXPIRED AGENT The high expired agent alarm limit has been violated. No

AGENT DETECTED Anesthetic agent has been detected by the gas monitor. No

HIGH MINUTE VOLUME The high minute volume alarm limit has been violated. No

LOW MINUTE VOLUME The low minute volume alarm limit has been violated. No

LOW SUSTAINED PAW The low sustained PAW alarm limit has been violated. No

LINE/FILTER BLOCK The sample line or filter is blocked. Yes

REVERSE FLOW The sample flow sensor has detected a reverse one-directional airway flow. Yes

WATER TRAP FULL, PUMP OFF The fluid collection bottle is full. No

GAS ANALYZER SATURATED There is moisture in the measurement chamber or the calibration is incorrect. No

HIGH CIRCUIT O2 The high circuit alarm limit has been violated. No

SPO2 INOPERATIVE The SpO2 circuits have failed. No





GE Ohmeda 7800/7810


VENT - MAIN MENUALARM LIMITS SETUP VIEW

ALARMS PRINT

VENT - SETUP MENULARGE TXTSMALL TXT

VENT - ALARM LIMITS

APNEA VMIN O2 PIP

VENT - ALARM LIMITS - PIPPIP

ON OFF

VENT - ALARM LIMITS - O2O2

ON OFF

VENT - ALARM LIMITS - VMINVMIN

ON OFF

VENT - ALARM LIMITS - APNEAAPNEA

ON OFF

GE Ohmeda 7800/7810

Contents
OverviewThe 90436A-08 Flexport system interface enables information from a GE Ohmeda 7800/7810 ventilator to be displayed on Spacelabs Healthcare monitors.



Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number


1200 7-bit odd 1 131-0685-xx (25-pin)

1.x or higher (7800)3.x or higher (7810)


GE Ohmeda 7800/7810










� � � � �

2 PIP

cmH2O 21 O2

% 9.9 Vmin

LVENT

98 Vt

ml

1 PEEP

cmH2O0 PLT

cmH2O

MODE:MECH VENT ON 29 RR

BPM

� � �

� � � �

VENT

VT = 98 ml

RR = 29 BPM

PIP = 2 cmH2O

PEEP = 1 cmH2O

� �


GE Ohmeda 7800/7810



� Measured oxygen level



� Measured tidal volume


� Measured respiratory rate

Mechanical ventilator — ON/OFF status

Measured inspiratory plateau pressure



Patient/room ID








� � � � �

� RR = 29 BPM O2 = 21% VENT

� APNEA = 30s PIP = 2 cmH2O

� VT = 98 ml PLT = 0 cmH2O

� VMIN = 9.9 L PEEP = 1 cmH2O

ICU 14


GE Ohmeda 7800/7810



• The Apnea alarm limit is fixed at 30 seconds.







APNEA 30 VMIN PIP 20 O2 73 VENT

VT = 98 ml3.0 18 RR = 28 BPM

PIP = 2 cmH2O

ICU 14PEEP = 1 cmH2O


GE Ohmeda 7800/7810










GE Ohmeda 7800/7810








VENT VOL MON STANDBY The ventilator is waiting for first breath to activate volume monitoring and apnea timer. No

CHECK VENT

The ventilator detects and reports one or more of the following alarm conditions:

• Sustained pressure alarm• Sub-atmospheric pressure alarm• AC fail (primary supply voltage low)• Low battery alarm• O2 limit set error• Vent setting range error• O2 sensor failure alarm• volume sensor failure• Maximum pressure > 60 cmH2O• Reverse flow• Low gas supply pressure alarm• Vent fail 0–12• Volume sensor cartridge coasting

(end of breath not detected)

Yes



GE Ohmeda Care-Plus/Infant Warmer

Directory of Keys

Note:WARMR will replace INCUB in the display when the unit is connected to the GE Ohmeda infant warmer.

INCUB

INCUB - MAIN MENUALARM LIMITS SETUP

*PRINT

INCUB - SETUP MENULARGE TXTSMALL TXT

INCUB - ALARM LIMITS

Pt AIR**

*This key appears on bedside monitors only.** This key appears only when the interface is connected to an incubator

INCUB - ALARM LIMITS - AIRAIR

ON OFF

INCUB - ALARM LIMITS - PtPt

ON OFF


Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OverviewThe 90444A-01 Flexport system interface allows information from a GE Ohmeda Care Plus incubator or infant warmer to be displayed on Spacelabs Healthcare monitors.

Configure the incubator/warmer as shown in Table 1. Consult the incubator/warmer manual for additional configuration setup procedures.

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the incubator/warmer, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the incubator/warmer. To control other interface functions, refer to the sections that follow.

Table 1: Incubator/Warmer Configuration

Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number

1200 7-bit odd 1 131-0686-xx




• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector on the incubator/warmer.



Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the incubator/warmer.

Incubator




� P-A is the difference between the patient temperature and the air temperature

� Control setting temperature

� INCUB parameter key

� � � �

0.6PA

C 35.4 CTRL

CINCUB

35.6 Pt

C

PATIENT CTRL 35.0 AIR

C

� � �

� �

INCUB

Pt = 35.6 C �AIR = 35.0 C �P-A = 0.6 C

CTRL = 35.4 C

� �

� � � � �

Pt = 35.6 C CTRL = 35.4 C INCUB

� AIR = 35.0 C PATIENT CTRL

ICU 14



� Current patient temperature


� Current air temperature inside incubator

� Incubator control mode:

• PATIENT CTRL indicates incubator is in the Patient Control mode

• AIR CTRL indicates incubator is in the Air Control mode

Patient/room ID

Infant Warmer




� � �

36.5 CTRL

CWARMR

36.3 Pt

C

SERVO MODE 65 POWER

%

� � �

� � �

WARMR

Pt = 36.3 C

POWER=65%CTRL = 36.5 C

� �

� � � � �

Pt = 36.3 C CTRL = 36.5 C WARMR

� POWER = 65.0% SERVO MODE

� ICU 14



� Control setting temperature

� WARMR parameter key

� Current patient temperature


� Current percentage of total available heater power being delivered to warmer

� Infant warmer control mode:

• SERVO MODE indicates infant warmer is in the Servo mode

• MANUAL MODE indicates infant warmer is in the Manual mode

� Patient/room ID



• the INCUB (or WARMR) key flashes,



When the interface is connected to an incubator:

• If the incubator is in Patient Control mode, you can turn ON the Patient alarm only.

• If the incubator is in Air Control mode, you can turn ON the Air alarm only.

• When both parameter alarms are turned OFF, status alarms will still cause the CHECK INCUB message to display.

When the interface is connected to an infant warmer:

• If the infant warmer is in Servo mode, you can turn ON the Patient alarm only.

• If the infant warmer is in Manual mode, no alarms are present.



• Touch INCUB (or WARMR).• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.



Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the incubator/

warmer.

• Alarm limits can only be adjusted at the incubator/warmer. Alarm violation is detected at the incubator/warmer and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• Alarm tones on the incubator/warmer can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.

Table 2 lists additional system alarms received from the incubator/warmer. Refer to the incubator/warmer manual for additional information.



Table 2: System Alarms

Incubator Infant Warmer

HIGH AIR TEMP HEATER POSITION

AIR CIRCULATION CHECK PATIENT

PROBE FAILURE PROBE FAILURE

SYSTEM FAILURE SYSTEM FAILURE

POWER FAILURE POWER FAILURE


• Touch INCUB.• Touch SETUP.• Select LARGE TXT or SMALL TXT.





Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the incubator/warmer or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the incubator/warmer is powered ON.



• Touch INCUB (or WARMR).• Touch PRINT.



GE Ohmeda Rascal II




ON OFF

GAS - SETUP

SIZE SWEEPSPEED

LARGE TXTSMALL TXT

GAS - SETUP - SIZE GAS - SETUP - SWEEP SPEEDWAVEFORM SIZE

↑SIZE

↓25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/secON OFF

GAS - ALARM LIMITS

FiO2 FiAGT RR EtCO2

GAS - ALARM LIMITS - EtCO2EtCO2 HI =

XXXLO = XXX ↑ ↓

EtCO2ON OFF FiO2

GAS - ALARM LIMITS - RRRR HI =

XXXLO = XXX ↑ ↓

RRON OFF EtCO2

GAS - ALARM LIMITS - FiAGTFiAGT HI =

XXXLO = XXX ↑ ↓

FiAGTON OFF RR

GAS - ALARM LIMITS - FiO2FiO2 HI =

XXXLO = XXX ↑ Ø

FiO2ON OFF FiAGT

GE Ohmeda Rascal II

Contents
OverviewThe 90443A-07 Flexport system interface enables information from a GE Ohmeda Rascal II gas monitor to be displayed on Spacelabs Healthcare monitors.






9600 8-bit none 1




• Plug the 25-pin female connector on the other end of the modular cable into the connector on the gas monitor labeled RS-232.

• Plug the 37-pin female connector into the ANALOG connector on the gas monitor.


GE Ohmeda Rascal II

Note:If the gas monitor does not have the analog option installed, turn the waveform option OFF (refer to Turning Waveforms ON or OFF on page 36-7).


Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the gas monitor.



� � � � � �

21 FiO2

% 0.89 FiENF

% 78 FiN2O

% 2 FiN2

% GAS

13 FiCO2

mmHg

12RR

BPM 0.75FeENF

%77 FeN2O

%1 FeN2

% 39EtCO2

mmHg

� � �

� � �

GAS

FiO2= 21%

FiENF= 0.89%

EtCO2= 39mmHg

RR= 12BPM

�


GE Ohmeda Rascal II


� Fractional inspired O2 value

� Fractional inspired agent value (parameter name will be FiHAL, FiENF, FiISO, FiDES, FiSEV, or FiAGT for halothane, enflurane, isoflurane, desflurane, sevoflurane, or an unidentified agent, respectively)

� Fractional inspired N2O

� Fractional inspired N2

� Fractional inspired CO2


� End tidal CO2

GAS parameter key

Fractional expired N2

� Fractional expired N2O

� Fractional expired agent (agent indication changes as noted in � above)

Respiration rate

Note:• Data displayed is delayed by at least six seconds from the data shown on the gas analyzer.

• COMMUNICATION LINK LOST will be displayed when the gas analyzer goes into calibration (CAL). If the operator does not promptly exit the CAL screen, the Flexport system interface will drop the Flexport screen from the bedside or central monitor (refer to <Plain>Status Messages on page 36-9).

� �

� FiO2=21% FiENF = 0.89%GAS

RR=12BPM FeENF=0.75%

� FiCO2=13mmHg FiN2O=78%

� EtCO2=39mmHg FeN2O=77%

� � �


GE Ohmeda Rascal II








analyzer.

• Alarm limits on the Flexport system interface are independent from the gas analyzer.

• Alarm violations detected at the gas analyzer may not be reported by the Flexport system interface if the alarm limit levels are different.


• Touch GAS.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


• Touch GAS.• Select ALARM LIMITS.• Select an alarm parameter.• Select HI= or LO=.• Use the arrow keys to adjust.


GE Ohmeda Rascal II

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the gas analyzer’s parameters (refer to Figure 36-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays GAS ALM OFF to the right of the GAS key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated. If an individual alarm is OFF, no limit values are displayed next to the parameter label.

Figure 36-4: Views Alarms screen








FiO2 45 FiENF 9.50 GAS

18 1.50

EtCO2 75 RR 4020 5


GE Ohmeda Rascal II



Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 1.56, 3.12, 6.25, 12.5 and 25 mm/second.


Selecting a Display FormatTwo display formats are available for the bedside monitors (refer to Display Detail on page 36-4).


• Touch GAS.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.






GE Ohmeda Rascal II





printout.


Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the gas analyzer or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the gas analyzer is powered ON.


• If the gas analyzer is calibrating, wait until it is finished, then return to normal monitoring.


• Touch GAS.• Select FREEZE ON.





Hamilton Amadeus/Veolar/Galileo/Raphael XTC

Directory of Keys

VENT

VENT - MAIN MENU

ALARM LIMITS SETUP

FREEZEMECHANICS MODE

XXX*UNKINOWN

MODEVIEW

ALARMS PRINTON OFF

*This could also be: UNKNOWN MODEMODE A/CONTRL

MODE SIMVMODE SPONT

MODE MMVMODE AMBIENTMODE PCV-CMVMODE PCV-SIMV

VENT - C in ml/cmH2O VENT - R in cmH2O/L/SC = XXX R = XXX

VENT - SETUP

SIZE SWEEP SPEED

WAVE TYPE

LARGE TXT

SMALL TXT

PATIENT PRESSURE

OPTIONAL PRESSURE FLOW VOLUME

50mm/sec

25mm/sec

12.5mm/sec

6.25mm/sec

3.12mm/sec

1.58mm/sec

WAVEFORM↑ ↓

ON OFF

VENT - ALARM LIMITS

RR VMIN FiO2 PIP PEEPPEEP alarms are not available from the Galileo/Raphael XTC ventilators.

RR VMIN FiO2 PIP PEEP

ON OFF ON OFF ON OFF ON OFF ON OFF


Contents
OverviewThe 90436A-07 Flexport system interface enables information from a Hamilton Amadeus/Veolar/ Galileo/Raphael XTC ventilator to be displayed on Spacelabs Healthcare monitors.



Vent Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number


Amadeus/Veolar 9600 7-bit even 2 131-0685-xx(25-pin) NIK01S.1

Galileo/Raphael XTC 9600 7-bit even 2 131-0686-xx

(9-pin) 3.2






Note:PLT pressures are not sent by ventilators in a non-pressure mode.






� � � �

30 PIP 20 FIO2 4.1 Vmin VENT

340 Vt

cmH2O % L mL

1 PEEP 29 PLT 9 MAP 10 RR

cmH2O cmH2O cmH2O BPM

� � � �






� Measured oxygen level


� Measured tidal volume


� Measured respiratory rate


Mean airway pressure

Measured inspiratory plateau pressure


� Patient/room ID

� �

VENT

VT = 340 mL

RR = 10 BPM �

PIP = 30 cmH2O �PEEP = 1 cmH2O

� �

� � � � �

� RR = 10 BPM FIO2 = 20% VENT

MAP = 9 cmH2O PIP = 30 cmH2O

� VT = 340 mL PLT = 29 cmH2O

� VMIN = 4.1 L PEEP = 1 cmH2O

� ICU 14


















Note:PEEP alarms are not sent by the Galileo and the Raphael ventilators.


Selecting a Display FormatTwo screen formats are available for the bedside monitor (refer to Display Detail on page 37-4).




To select a screen format:


RR 29 VMIN 4.1 PIP 79 VENT

VT = 340 mL0.2 RR = 29 BPM

ICU 14 FIO2 20 PEEP ON PIP = 30 cmH2O10 PEEP = 1 cmH2O



Printing the Current DisplayTouch the PRINT key to print the information shown on the current screen. Each recording is identified by the bed name, patient name, time, and date.









Table 2 displays the status messages that the Flexport system interface reports for the ventilator during Flexport system interface operation.





GENERAL ALARM Loss of power or inappropriate voltage levels internally. Yes

DISCONNECT PATIENT Patient coughs, patient fights against the ventilator, an acute change in lung compliance/airway resistance. Yes

APNEACessation of breathing during spontaneous modes. Patient has not exhaled at least 50 ml/second flow through the flow sensor during the last 20 seconds.

Yes

DISCONNECTED VENTTubing disconnected, large air leaks, hiccups, defective expiratory membrane, or incorrect flow sensor measurement.

Yes

OPERATOR Fan filter occluded, flow sensor backward, or incorrect control setting. Yes

GAS SUPPLY Gas supply failure. Yes



Infrasonics Adult Star 2000



MODEVIEW

STATUSVIEW

ALARMS PRINT

VENT - SETUPLARGE TXTSMALL TXT

ANES - ALARM LIMITS

RR VT VMIN PIP PEEP I:E APNEA

VENT - ALARM LIMITS - APNEAAPNEA HI =

XXRR

ON OFF APNEA

VENT - ALARM LIMITS - I:EI:E LO =

X.XI:E

ON OFF APNEA

VENT - ALARM LIMITS - PEEPPEEP LO =

XXXPEEP

ON OFF I:E


XXLO = XXX

PIPON OFF PEEP

VENT - ALARM LIMITS - VMINVMIN LO =

XXXVMIN

ON OFF PIP

VENT - ALARM LIMITS - VTVT HI =

XXXLO = XX.X

VTON OFF VMIN


XXRR

ON OFF VT


Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Ventilator Mode History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
OverviewThe 90436A-05 Flexport system interface enables information from an Infrasonics Adult Star 2000 ventilator to be displayed on Spacelabs Healthcare monitors.



Baud Rate

Character Length

Parity Setting

Stop Bit

TransitionConnector

Part Number


2400 8 bit none 1 131-1155-xx 216 or higher











• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 jack on the ventilator.

� � � � � �


405 VT

I:E cmH2O cmH2O % mL

1.8 5 PEEP 20 MAP 4.0 VMIN 10 RR

cmH2O cmH2O L BPM

� � �

� � �

VENT

VT= 405 mL

RR= 10 BPM

PIP= 68 cmH2O

PEEP= 5 cmH2O

� �




� Ratio of inspiration time to expiration time (I:E ratio is typically expressed as 1:X.X where X.X is the value displayed and equals E/I)

� Current peak inspiratory pressure value

� Current inspiratory plateau pressure value

� Current fractional inspired O2 value


� Current tidal volume value


Current respiratory rate value

Current minute volume value

� Current mean airway pressure value

� Current positive end expiratory pressure value

Patient/room ID

� � � � � �

RR = 10 BPM VT = 405 mL VENT

� FiO2 = 21% PIP = 68 cmH2O

� PEEP = 5 cmH2O MAP = 20 cmH2O

VMIN = 4.0 L I : E = 1.8

ICU - 4


















VT HI LIMIT will be present if the alarm is ON and the ventilator is in PCV/Time Cycled or PCV/I:E Cycled mode, but will not be present in Volume Cycled mode.


Viewing StatusThe VIEW STATUS key enables you to display the recent status messages sent by the ventilator. A maximum of four messages can be simultaneously displayed on the bedside monitor and three messages can be simultaneously displayed on the remote monitor (refer to Status Messages on page 38-10). When more than four messages are received from the ventilator, they are displayed in receiving order.





PIP 120 VT 650 APNEA 20 VENT

405VT

3 160 mL

I : E PEEP VMIN RR 70 10 RR

1.0 2 0.3 BPM



Viewing Ventilator Mode HistoryChronological history of the last eight ventilator mode settings are displayed with the oldest value at the top of the left column and the most recent value at the bottom of the right column. Possible modes include ASST/CTL, SIMV, CPAP, SIMV+PPS, CPAP+PPS, and APNEA.

Figure 38-5: View Mode screen



To view ventilator mode history:




15:47 ASST/CTL 15:49 ASST/CTL VENT

405 VT

15:47 SIMV 15:49 CPAP+PPS mL

15:47 SIMV+PPS 15:51 CPAP 10 RR

15:49 CPAP 15:56 SIMV BPM

















LOW PRS O2 INLET Pressure at the oxygen inlet fitting is less than 30 psig and the O2% is 22 or greater. No

LOW PRS AIR INLET Pressure at the air inlet is equal to or less than 30 psig. No

LOW BATTERY Available power life is less than 4 minutes. No

OBSTRUCTED TUBE Airway is obstructed or airway pressure line is obstructed. No

AIRWAY LEAK Leak of 6 LPM or more has been detected. No

EXHAL VALVE LEAK Exhalation flow is greater than 10% of inhaled set flow. Leak is greater than 4 LPM for 60 milliseconds. No

HIGH PEEP/CPAP The baseline pressure has fluctuated between 6 to 10 cmH2O above set parameter for more than 5 seconds. No

SHORT INSP TIME Inspiratory time is less than 240 milliseconds for mechanical breaths. No

SHORT EXHAL TIME Exhalation time is less than 200 milliseconds for mechanical breaths or 260 milliseconds for PPS breaths. No


Maquet Siemens Servo 300


VENT - MAIN MENU

SETUPFREEZE LARGE TXT TABULAR

MODEVIEW

ALARMS PRINTON OFF SMALL TXT

VENT - SETUP WAVE SIZE

↑SIZE

↓SWEEP SPEED

WAVE TYPEON OFF PRS FLOW

FLOW - SETUP - SWEEP SPEED25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing the Ventilator Mode History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Status Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OverviewThe 90436A-03 Flexport system interface enables information from a Maquet Siemens Servo 300 ventilator to be displayed on Spacelabs Healthcare monitors.

Warning:This product does not support alarms.




Character Length



Part Number


Servo 300 9600 8 bit even 1 131-1067-xx(26-pin) COM x1.01











• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the data communication connector (N82) of the

ventilator.

� � � � � �


0.33 Vt WAVE=FLOWcmH2O cmH2O % L

4 PEEP 98 MAP 7.6 Vmin 22 RRcmH2O cmH2O L BPM

� �

� � �

VENT

Vt = 0.33 L WAVE=PRESSRR = 72 BPM �

PIP = 13 cmH2O �FiO2 = 20 % �




� Measured peak inspiratory pressure (PIP)

� Plateau pressure (PLT)

� Measured oxygen level (FiO2)


� Measured tidal volume (Vt)

� Waveform type (PRESSURE or FLOW)

� Measured respiratory rate (RR)

Measured minute volume (Vmin)

Mean airway pressure (MAP)

� Positive end expiratory pressure (PEEP)





• Touch VENT.• Touch SETUP.• Select WAVEFORM ON/OFF.

� �

� Vt = 0.33 L PIP = 13 cmH2O VENT

Vmin = 7.5 L MAP = 5 cmH2O

� RR = 22BPM PLT = 81 cmH2O

� FiO2 = 20% PEEP = 4 cmH2O

� � �





Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 25, 12.5, 6.25, and 3.12 mm/second.








• Touch VENT.• Touch SETUP.• Touch WAVE.• Select PRS or FLO.







Viewing the Ventilator Mode HistoryThe last eight ventilator mode settings that were used are displayed in the waveform zone. The oldest value is at the top of the left column. The most recent value at the bottom of the right column.









Viewing Status MessagesThe VIEW STATUS key allows you to display the recent status messages sent by the ventilator.



printout.


Status MessagesThis section includes information on how to recognize and respond to a status message.

The message COMMUNICATION LINK LOST indicates a problem with the ventilator or cabling. If the monitor displays this message, perform the following troubleshooting steps:










VENT - MAIN MENU

SETUPFREEZE LARGE TXT VIEW

STATUS PRINTON OFF SMALL TXT

VENT - SETUP WAVE SIZE

↑SIZE

↓SWEEP SPEED

WAVE TYPEON OFF PRS FLOW


mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OverviewThe 90436A-02 Flexport system interface enables information from a Maquet Siemens Servo 900 ventilator to be displayed on Spacelabs Healthcare monitors.

Warning:This product does not support alarms.

Note:• The Maquet Siemens Servo 900 ventilator updates the patient’s parameter data with each patient

breath cycle and sends this information through the Maquet Siemens 990 digital interface to the Flexport. In Ventilator Assist, the ventilator updates the respiration rate value only after each detected breath. The updated respiration rate is correctly displayed on the bedside monitor.

• If a patient does not take a subsequent breath, the data displayed will remain unchanged indefinitely because the 990 digital interface will not update the displayed values.



Baud Rate

Character Length



Part Number


9600 8 bit even 1 131-0685-xx(25-pin) COM x1.01











• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the data communication connector (N82) of the

ventilator.

� � � � � �


0.33 Vt WAVE=FLOWcmH2O cmH2O % L

4 98 MAP 7.6 Vmin 22 RRcmH2O L BPM

� �

� � �

VENT

Vt = 0.33 L WAVE=PRESSRR = 72 BPM �

PIP = 13 cmH2O �FiO2 = 20 % �




� Measured peak inspiratory pressure (PIP)

� Plateau pressure (PLT)

� Measured oxygen level (FiO2)


� Measured tidal volume (Vt)

� Waveform type (PRESSURE or FLOW)

� Measured respiratory rate (RR)

Measured minute volume (Vmin)

Mean airway pressure (MAP)

� Positive end expiratory pressure (PEEP)





• Touch VENT.• Touch SETUP.• Select WAVEFORM ON/OFF.

� �

� Vt = 0.33 L PIP = 13 cmH2O VENT

Vmin = 7.5 L MAP = 5 cmH2O

� RR = 22BPM PLT = 81 cmH2O

� FiO2 = 20% PEEP = 4 cmH2O

� � �





Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 25, 12.5, 6.25, and 3.12 mm/second.








• Touch VENT.• Touch SETUP.• Touch WAVE.• Select PRS or FLO.









printout.










Status MessagesThis section includes information on how to recognize and respond to a status message.






Masimo Radical

Directory of KeysLINK

LINK - MENUALARM LIMITS SETUP


ON OFF


LINK - SETUP

SIZE SWEEP SPEED

LARGE TXTSMALL TXT

LINK - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF

LINK - SETUP - SWEEP SPEED50

mm/sec25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec0.78

mm/sec0.39

mm/sec

LINK - ALARM LIMITS

SPO2 PR

LINK - ALARM LIMITS - PRPR HI =

XXLO = XXON OFF

LINK - ALARM LIMITS - SpO2SPO2 HI =

XXLO = XXON OFF

Masimo Radical

Contents
OverviewThe 90442A Flexport system interface enables information from a Masimo Radical pulse oximeter to be displayed on Spacelabs Healthcare monitors.

Configure the pulse oximeter as shown in Table 1. Consult the pulse oximeter manual for additional configuration setup procedures


Baud Rate Minimum Software Revision Installation Kit Part Number


Part Number

9600Masimo SET V3.0.2.2Handheld R2.1.0.5D-Station R2.1.0.7

045-0152-xx 131-1755-xx (9-pin)


Masimo Radical

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the pulse oximeter, complete the steps listed in the following Quickstart.







• Plug the other end of the modular cable into the transition connector.• Power on the pulse oximeter and set it up to communicate with the

Spacelabs Healthcare protocol.• Plug the transition connector into the RS-232 connector on the pulse oximeter serial

port.

� �

LINK

98SpO2

%

70 PR

bpm

� �


Masimo Radical



� LINK parameter key




� Patient/room ID

� �

LINK

SpO2= 98%

PR= 70bpm

� �

� �

� SpO2 = 98% LINK

� PR = 70bpm

� ICU - 4


Masimo Radical



• the LINK key flashes,




Note:• Turning interface alarms ON or OFF does not affect alarm settings on the pulse oximeter.

• Alarm limits can only be adjusted at the pulse oximeter. Alarm violation is detected at the pulse oximeter, and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• The SpO2 high limit can be turned OFF at the pulse oximeter. When this high limit is OFF, the value 101 is displayed as the SpO2 high limit on the Spacelabs Healthcare monitor(s).



• Touch LINK.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


Masimo Radical

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the pulse oximeter’s parameters (refer to Figure 41-4). If alarms for both parameters are turned OFF, the Spacelabs Healthcare monitor displays LINK ALM OFF to the right of the LINK key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.






• Touch LINK.• Touch VIEW ALARMS.


• Touch LINK.• Touch SETUP.• Touch SIZE.• Select WAVEFORM ON/OFF.

SpO2 100 LINK

98SpO2

85 %

PR 180 70 PR

40 bpm


Masimo Radical








• Touch LINK.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.


• Touch LINK.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.


• Touch LINK.• Touch SETUP.• Select LARGE TXT or SMALL TXT.


Masimo Radical





printout.






• Touch LINK.• Select FREEZE ON.


• Touch LINK.• Touch PRINT.



Mortara ELI 100/STM

Directory of Keys

ST

ST - MAIN MENUALARM LIMITS

WAVEFORM SIZE SETUP RHYTHM

LEAD PRINT

ST - RHYTHM LEADI II III V1 V2 V3 V4 V5 V6 AVF AVL AVR

ST - SETUP

SWEEP SPEED QRS TONE

WAVEFORM ST VALUES

ON OFF ON OFF

ST - SETUP - QRS TONETONE VOLUME

↑VOLUME

↓ON OFF

ST - SETUP - SWEEP SPEED

50mm/sec

25mm/sec

12.5mm/sec

ST - WAVEFORM SIZE

SIZE ↑

SIZE ↓

ST - ALARM LIMITSALARMS SINGLE

ST = XXXMULTI

ST = XXXON OFF

Mortara ELI 100/STM

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Adjusting the Waveform Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Selecting a Rhythm Lead Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OverviewThe 90440A-01 Flexport system interface enables information from a Mortara Instrument ELI 100/STM ST monitor to be displayed on Spacelabs Healthcare monitors.

The ST monitor must have a monitoring session in progress before data will be sent to the Flexport system interface. To begin a monitoring session on the ST monitor, complete the steps listed in the following Quickstart.

Configure the ST monitor as shown in Table 1. Consult the ST monitor manual for additional configuration setup procedures.

Table 1: ST Monitor Configuration


Parity Setting

Stop Bit

19,200 8 bit even 1

To start an ST monitoring session from the Mortara ST monitor:

• Touch ON/OFF/DC (function key) to access the main menu.• Touch MON to access ST monitoring.• Touch YES to start a new monitoring session.• Touch YES to clear previous patient data.• Touch YES for New Patient.• Enter patient ID information.

NOTE: The ST monitor acquires a template ECG, prints it, and begins monitoring. The ST monitoring menu appears.


Mortara ELI 100/STM

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the ST monitor, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the ST monitor. To control other interface functions refer to the sections that follow.

Display DetailWhen you power ON an Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the ST monitor.

Figure 42-1: Bedside/remote monitor, full screen





• Plug the 9-pin male connector on the other end of the modular cable into the RS-232 connector on the ST monitor labeled SERIAL.

� � � �

I 20 AVR -10 V1 05 V4 10 LEAD = V3II 00 AVL 20 V2 00 V5 00 S

TST = -20uV

III -20 AVF -10 V3 -20 V6 -15

ICU - 5

� � �

� �

I 20 V2 00 V6 -15II 00 V3 20 AVR -10 S

TIII -20 V4 10 AVL 20V1 05 V5 00 AVF -10

� ICU - 5


Mortara ELI 100/STM

� ST values for 12 leads

� ST parameter key

� Selected rhythm lead designator

� QRS detect indicator


� ST value for selected lead

� Patient/room ID (appears on remote and central monitors only)

Enabling AlarmsThe Alarm Limits menu allows you to enable alarm limits for SINGLE ST and MULTI ST alarms. The SINGLE ST segment level alarm is violated when the magnitude of a single ST segment level exceeds the single lead threshold. The MULTI level alarm is violated when the magnitude of any two or more leads exceeds the two-lead threshold.

When an alarm is turned ON and that parameter value exceeds an alarm limit, all of the following occur:

• the alarm limits key for that parameter flashes,

• the parameter value flashes,

• the ST key flashes, and



Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the ST monitor.

• Alarm limits can only be adjusted at the ST monitor. Alarm violation is detected at the ST monitor, and the Flexport system interface reports the alarm if the alarm key is turned ON.

• Alarm reporting may not occur simultaneously at the ST monitor and the Spacelabs Healthcare monitor. The alarm may be reported at the Spacelabs Healthcare monitor before it is reported at the ST monitor.


• Touch ST.• Select ALARM LIMITS.• Select ALARMS ON or OFF.


Mortara ELI 100/STM


Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 50, 25, and 12.5 mm/second.


Adjusting the QRS ToneThe QRS tone can be turned ON or OFF. When it is ON, you can adjust the volume level.

The default setting is TONE OFF.


• Touch ST.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.

To adjust the QRS tone:

• Touch ST.• Touch SETUP.• Touch QRS TONE.• Touch TONE ON.• Adjust the volume using VOLUME ↑ or VOLUME ↓


Mortara ELI 100/STM

Turning Waveforms ON or OFFYou can turn waveforms OFF and display only the numeric values. When waveforms are OFF, the WAVEFORM SIZE key, the SWEEP SPEED key, and the SIZE ↑ and SIZE ↓ keys are disabled.


Enabling the ST Values on the DisplayThe ST Values screen can be enabled or disabled. Use the ST VALUES ON/OFF key to enable or disable the ST Values screen.

The default setting is ST VALUES ON.




• Touch ST.• Touch SETUP.• Touch WAVEFORM ON/OFF.

To enable the ST values screen:

• Touch ST.• Touch SETUP.• Touch ST VALUES ON/OFF.


• Touch ST.• Touch WAVEFORM SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.


Mortara ELI 100/STM

Selecting a Rhythm Lead WaveformYou can select one of the twelve waveforms for display.

The default depends upon the settings on the ST monitor.



printout.


To select a rhythm lead:

• Touch ST.• Touch RHYTHM LEAD.• Select desired lead.

To print the ST monitor display:

• Touch ST.• Touch PRINT.


Mortara ELI 100/STM

Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the ST monitor or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the ST monitor is powered ON.


• Verify that the ST monitor has monitoring enabled.

Table 2 lists the status messages that the Flexport system interface reports for the ST monitor during Flexport system interface operation.

Note:If the ST monitor’s directory fills to capacity, the ST monitor will stop sending data to the Flexport system interface and the ST monitor’s parameter zone will drop from the Spacelabs Healthcare monitor.




Communication between the ST monitor and the Spacelabs Healthcare monitor has been interrupted. Yes

LEAD FAULT A lead(s) failure in the standard lead set — correct the faulty leads. Yes

NOISY SIGNALExcessive high frequency noise on the baseline (muscle tremor) — check on patient preparation and/or patient movement.

Yes

NO QRS DETECTION

No QRS complexes were detected in the 10 second record — correct the condition causing the invalid ECG. Yes


Newport Medical Instruments E150/E200

Directory of Keys

VENT

VENT - MAIN MENU

ALARM LIMITS SETUP VIEW

ALARMS PRINT

VENT - SETUP LARGE TXT

SMALL TXT

VENT - ALARM LIMITS

VMIN RR PIP MAP

VENT - ALARM LIMITS - MAPMAP HI =

XXLO = XXON OFF


XXLO = XXON OFF


XXLO = XXON OFF

VENT - ALARM LIMITS - VMINVMIN HI =

XXLO = XXON OFF



Contents
OverviewThe 90442A Flexport system interface enables information from Newport Medical Instruments E150 and E200 ventilators to be displayed on Spacelabs Healthcare monitors.



Baud Rate TransitionConnector Part Number Minimum Software Revision

9600 Provided by Newport Medical Instruments

E150: V1.5E200: Main - R5.17B; Panel - R5.10BSL 300: V1.3






• Plug one end of a modular cable into the modular jack on the Flexport system interface.• Plug the other end of the modular cable into the modular jack labeled “FLEXPORT” on

the SL 300 interface adapter.• Plug one end of another modular cable into the modular jack labeled “VENT” on the

SL 300 interface adapter.• Plug the other end of the modular cable into the transition connector on either the E150

or E200 ventilator.• Plug the transition connector into the connector labeled “RS232” on the ventilator.• Connect the wire from the Newport Medical AC adapter to the connector labeled

“POWER” on the SL 300 interface adapter and plug the AC adapter into a wall outlet.• Turn ON the ventilator, and then turn ON the SL 300 interface adapter. Note that the

SL 300 will sound a continuous alarm for up to one minute after the power is turned ON (until it receives a data packet from the ventilator, which comes in one-minute intervals).





Display DetailWhen you power ON an Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the ventilator.

Figure 43-2: Bedside monitor, large text screen; Central monitor, full screen

SDLCcable

SDLCterminator

Newport

Newport

WAVEE200

Ventilator

BREEZEE150

Ventilator

NewportMedicalInstrumentsSL 300

adapter

OR

modularcables

25-pin transitionconnector

9-pin transitionconnector

connectionlabeled“VENT”

connectionlabeled“FLEXPORT”

connectionlabeled“POWER”

Newport MedicalInstruments AC adapter

interface

SpacelabsHealthcare monitor

systemFlexport

interface

� � � � �

5 PIP 40 O2 4.2 VMIN VENT

0.28 VT

cmH2O % L L

2 MAP 1 PEEP 15 RR

cmH2O cmH2O BPM

� �





� Peak inspiratory pressure — displays high pressure alarm

� FiO2 — sets oxygen concentration

� Inspiratory minute volume — displays low and high minute volume alarms (Vmin is not displayed on the BREEZE 150)


� E200: inspiratory tidal volume shows the larger of mandatory or voluntary tidal volumeE150: set tidal volume is shown


� Respiratory rate — displays apnea alarm

Positive end expiratory pressure — displays the baseline pressure

Mean airway pressure — displays low pressure alarm

� Patient/room ID

� � ��

VENT

VT= 0.28L

RR= 15BPM

PIP= 5cmH2O

MAP= 2cmH2O

� � � �

� VT=0.28L O2= 40% VENT

� RR = 15bpm PEEP= 1cmH2O

� PIP= 5 cmH2O VMIN= 4.2L

MAP= 2cmH2O

� ICU 14

















Viewing Alarm SettingsThe VIEW ALARMS key normally enables you to display the current alarm settings for all parameters. However, this data is not currently available from the ventilator, and dashes are shown instead.

If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays VENT ALM OFF to the right of the VENT key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.








VENT

0.25 VT

VMIN PIP L

26 RR

RR MAP BPM

..





Status MessagesThe message COMMUNICATION LINK LOST indicates a problem between the Flexport system interface and the Spacelabs Healthcare interface adapter. The message VENTILATOR LINK LOST indicates a problem between the SL 300 and the ventilator. If the monitor displays either message, perform the following troubleshooting steps:



UFP Parameter KeyIf the letters UFP are displayed on the parameter key instead of VENT, the Flexport system interface has entered a self-test mode. This can happen if power is applied to the Flexport system interface (via the SDLC cable) before power is applied to the Newport Medical Instruments SL 300 interface adapter. This can be corrected as follows:

• Apply power to the SL 300 interface adapter.

• Cycle the power to the Flexport system interface by unplugging and plugging in the SDLC cable.





Oridion VitalCap


CO2 - MAIN MENUALARM LIMITS SETUP

FREEZE TOGGLESILENCE

VIEW ALARMS PRINT

ON OFF

CO2 - SETUP

SIZE SWEEPSPEED

LARGE TXTSMALL TXT

CO2 - SETUP - SIZE CO2 - SETUP - SWEEP SPEEDWAVEFORM SIZE

↑SIZE

↓25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/secON OFF

CO2 - ALARM LIMITS

ETCO2 RR FlCO2

CO2 - ALARM LIMITS - FlCO2FlCO2 HI =

XXXON OFF


XXXLO = XXXON OFF


XXXLO = XXXON OFF


Oridion VitalCap

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Silencing Alarm Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
OverviewThe 90442A Flexport system interface enables information from an Oridion VitalCap portable bedside capnograph to be displayed on Spacelabs Healthcare monitors.

Configure the capnograph as shown in Table 1. Consult the capnograph manual for additional configuration setup procedures.

Table 1: Capnograph Configuration

Baud Rate Minimum Software Revision Installation Kit

Part Number

9600 2.75 045-0155-xx


Oridion VitalCap

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the capnograph, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the capnograph. To control other interface functions, refer to the sections that follow.




• Connect the other end of the modular cable (DB25 male) to the VitalCap Interface Adapter.NOTE: In the package, one end of the RJ45 monitor cable is connected to the VitalCap Interface Adapter.

• Connect the loose end of the RJ45 cable to the capnograph.• Turn on the capnograph.


Oridion VitalCap

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the capnograph.





� Current end-tidal CO2 (EtCO2) value


� Current respiratory rate (RR) value

� Current fractional inspired CO2 (FiCO2) value

� �

CO2

30 EtCO2

mmHg

20RR

bpm

� �

� �

CO2

EtCO2 = 30mmHgRR = 20bpm �FiCO2 = 0.0mmHg �

�

� �

EtCO25015 FiCO2

8CO2

EtCO2 = 30mmHgRR = 20bpm �

RR30 FiCO2 = 0.0mmHg �6

�


Oridion VitalCap








Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the capnograph.

• Alarm limits can only be adjusted at the capnograph. Alarm violation is detected at the capnograph, and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• The No Breath alarm replaces all other alarms and is indicated by low RR (RR flashes).




Oridion VitalCap

Silencing Alarm TonesThere are two types of alarm silence for the capnograph: temporary (lasting one or two seconds) and constant.

Temporary silence is enabled or disabled by touching the capnograph’s SILENCE key or by touching the TOGGLE SILENCE key on the Spacelabs Healthcare monitor.

Constant silence is set from the Alarm Silence menu on the capnograph. When the constant silence is enabled, the temporary silence has no effect because the constant silence has a higher priority. If you cancel the constant silence while the temporary silence is active, the alarms will remain silent until the time-out of the temporary silence.

Regardless of how the alarms are silenced:

• Audible tones on the capnograph and the Spacelabs Healthcare monitors are silenced.

• Alarm recordings and alarm watches are disabled on the Spacelabs Healthcare monitors.

• The flashing of the CO2 key and the large bell on the Spacelabs Healthcare monitors ceases.

• If the parameter is displayed as a numeric key, no indication of an alarm is displayed.

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the capnograph’s parameters (refer to Figure 44-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays CO2 ALM OFF to the right of the CO2 key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.


Note:The VIEW ALARMS key is not available on the central monitor, split screen.



EtCO25015 FiCO2 8 C

O2

30 EtCO2

mmHg

RR 306 20 RR

bpm


Oridion VitalCap





Note:• The WAVEFORM ON/OFF key must be set to ON for the size keys to appear and function.

• If the capnograph is set up for “Small CO2 Scale” (either 0 to 50 mmHg or 0 to 7 kPa/Vol%), two sizes are available.

• If the capnograph is set up for “Large CO2 Scale” (either 0 to 99 mmHg or 0 to 14 kPa/Vol%), only one size is available.


• Touch CO2.• Touch SETUP.• Touch SIZE.• Select WAVEFORM ON/OFF.


• Touch CO2.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.


Oridion VitalCap

Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 25, 12.5, 6.25 or 3.12 mm/second.

The default setting is 12.5 mm/second for neonatal patients and 6.25 mm/second for adult patients.





• Touch CO2.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.




• Touch CO2.• Select FREEZE ON.


Oridion VitalCap


Note:• The patient name you enter on the Spacelabs Healthcare monitor is the name that appears on the

printout.





Oridion VitalCap

Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the capnograph or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the capnograph is powered ON.


Table 2 lists the status messages that the Flexport system interface reports for the capnograph during Flexport system interface operation.





NO BREATH No valid breath has been detected.

BATTERY EMPTYBattery pack is discharged. Replace or recharge the battery, or connect the VitalCap monitor to AC power.

STANDBY Standby mode. To monitor patient, exit standby mode.

CO2 FAILURE Instrument fault. Contact authorized service representative.

BATTERY LOWBattery charge level is low. Replace or recharge the battery, or connect the VitalCap monitor to AC power.

FILTERLINEFilter line is disconnected or is not securely connected. Connect the filter line to the input connector on the VitalCap or tighten the connection.

BLOCKAGE

Filter line is twisted or clogged. The message appears after 30 seconds of unsuccessful clearing. Check the filter line and, if necessary, replace it.

Microstream airway adapter is clogged. Check the Microstream airway adapter and, if necessary, replace it.

RECALIBRATE CO2 Needs calibration. Recalibrate the VitalCap.

CLEARING FILTERLINEFilter line tube is twisted or clogged with water. Check the filter line and, if necessary, untwist or replace it.



OSI OpticalCAM

Directory of KeysABG

ABG - MAIN MENU

SETUP PRINT

CO2 - SETUP LARGE TXTSMALL TXT

OSI OpticalCAM

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Selecting a Unit of Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
OverviewThe 90442A Flexport system interface allows information from an Optical Sensors Incorporated (OSI) OpticalCAM Blood Measurement System to be displayed on Spacelabs Healthcare monitors.

Configure the blood gas analyzer as shown in Table 1. Consult the analyzer manual for additional configuration setup procedures.

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the blood gas analyzer, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the blood gas analyzer. To control other interface functions, refer to the sections that follow.


Baud Rate Transition Connector Part Number

9600 131-0685-xx




• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the monitoring port on the back of the blood gas

analyzer.


OSI OpticalCAM

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the blood gas analyzer.



� Time value from the OpticalCAM monitor time clock (hours and minutes) — indicates time at which the ABG was measured.

Note:The times displayed in the tabular or graphic trend displays of the Spacelabs Healthcare monitor are set by the Spacelabs Healthcare clock.

� Base excess

� PH

� ABG parameter key

� Partial pressure of dissolved carbon dioxide in arterial blood

� Partial pressure of dissolved oxygen in arterial blood

� Bicarbonate

Oxygen saturation

Total carbon dioxide

� � � � �

1642 Time -1 BE

mEq/L 7.38 pH

ABG

40 PCO2

mmHg

25.2TCO2

mmol 97SaO2

%24 HCO3

mEq/L 98PO2

mmHg

� �

� �

ABG

pH = 7.38

PCO2 = 40mmHg �PO2 = 98mmHg �Time = 1642 �


OSI OpticalCAM



Selecting a Unit of MeasurementThe PCO2 and PO2 values can be displayed in units of millimeters of mercury (mmHg) or kilo Pascals (kPa). Complete the steps in the following Quickstart.




• Touch ABG.• Touch SETUP.• Select LARGE TXT or SMALL TXT.

To select the unit of measurement from the OpticalCAM monitor:

• Power up the blood gas analyzer.• Touch SETUP MENU.• Select SERVICE.• Enter your password.• Select UNITS OF MEASURE.• Use the control knob to select mmHg or kPa.


• Touch ABG.• Touch PRINT.


OSI OpticalCAM

Status MessagesNote:

If an OpticalCAM monitor error occurs, a general error message will be displayed on the Spacelabs Healthcare monitor. The error message will refer you to the blood gas analyzer for more specific information.

The message COMMUNICATION LINK LOST or ABG LINK LOST indicates a problem with the blood gas analyzer or the cabling. If the monitor displays either of these messages, perform the following troubleshooting steps:

• Verify that the blood gas analyzer is powered ON.




PhysioFlex



FREEZE SWITCHWAVES

VIEW ALARMS

*PRINT

ON OFF

VENT - SETUP * These keys are displayed on the bedside monitor only.

SIZE SWEEPSPEED

LARGE TXT *SMALL TXT

VENT - SETUP - SIZE VENT - SETUP - SWEEP SPEEDWAVEFORM SIZE

↑SIZE

↓12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/secON OFF

VENT - ALARM LIMITS

FiAn FiCO2


XXLO = XX

FiO2ON OFF FiAn

VENT - ALARM LIMITS - FiAnFiAn HI =

XXXFiAn

ON OFF FiO2

PhysioFlex

Contents
OverviewThe 90442A Flexport system interface enables information from a PhysioFlex anesthesia ventilator to be displayed on Spacelabs Healthcare monitors.


In order to communicate with Spacelabs Healthcare equipment, the ventilator should be equipped with a Spacelabs Healthcare communications option. Check the Options screen on the ventilator monitor to verify that the Spacelabs Healthcare communications option is present. The System Information box on the ventilator monitor should contain the following line:

Data protocol: SL X,YY (where X, the major revision number, should be 1 or higher and YY can be any number)

The ventilator needs no further configuration.



InstallationKit Part Number

9600 6.04.01 045-0035-xx (Spacelabs)5501 5001 (Physio Medical)


PhysioFlex









• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the ventilator, at the backside of the monitor DOME.

� � � � � �

446 Vt

ml 11 RR

BPM 1.1 FiAn

% VENT

31 FiO2

%

218VO2

ml pm 22Ppeak

cmH2O 1.0 FetAn

% 7.9etCO2

%

� �

� � � �

VENT

FiO2 = 31%etCO2 = 7.9%FetAn = 1.0%

VO2 = 218 ml pm �


PhysioFlex


� Current tidal volume in milliliters

� Current respiration rate in breaths per minute

� Current inspired anesthetic agent concentration in %


� Current inspired oxygen concentration in %


� Current end tidal CO2 concentration (units as selected on ventilator)

Current end tidal anesthetic agent concentration

Current peak airway pressure in cmH2O

� Current oxygen fresh gas flow in milliliter per min

� Patient/room ID








� � �

� FiO2 = 31% RR = 11BPM VENT

� etCO2 = 7.9% Ppeak = 22cmH2O

� Vt = 446ml FiAN = 1.1%

� VO2 = 218ml pm FetAn = 1.0%

� ICU 14


PhysioFlex










FiAn 1.1 VENT

FiO2 = 31%etCO2 = 7.9%

FiO2 100 FetAn = 1.0%18.0 VO2 = 218 ml pm

ICU 14


PhysioFlex

Entering Setup InformationChanging setup information is helpful in optimizing the monitor display. The SETUP key accesses the functions described below and affects only the monitor at which these adjustments are made.










PhysioFlex



Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 1.56, 3.12, 6.25, and 12.5 mm/second.

The default sweep speed is 6.25 mm/second.










PhysioFlex



printout.










COMMUNICATION LINK LOST Communication between the Flexport system interface and the ventilator is interrupted. Yes

CO2 WAVE SELECTED The SWITCH WAVES key was touched and the CO2 waveform is presently displayed. No

PAW WAVE SELECTED The SWITCH WAVES key was touched and the airway pressure waveform is presently displayed. No


PiCCO

Directory of Keys

PiCCO

PiCCO - MAIN MENULARGE NUM

PRINTSMALL NUM


PiCCO

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
OverviewThe 90439 Flexport system interface enables continuous cardiac output (CCO) information from a Pulsion PiCCO plus to be displayed on Spacelabs Healthcare monitors. Consult the manufacturer's manual for configuration of the PiCCO device.

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the PiCCO device, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the PiCCO device. To control other interface functions, refer to the sections that follow.

Table 1: PiCCO Configuration

Baud Rate


Transition Connector Part Number

19200 PiCCO 7.x 131-1399-xx




• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 9-pin connector on the PiCCO monitor.


PiCCO

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the PiCCO device.




� PiCCO parameter key

� Pulse contour cardiac index

� Global end-diastolic volume index

� � � �

PiCCO

PCCI = 1.66GDVI = 715SVRI = 1563ELWI = 9

�

� � � � �

3 SVV 1185 dPmx 1563 SVRI PiCCO

1.66 PCCI

TD Values17:07 08.01.2007 37 9 715GEF ELWI GDVI

� � � �

� �

� PCCI = 1.66 GDVI = 715 PiCCO

� SVRI = 1563 ELWI = 9� dPmx = 1185 GEF = 37� SVV = 8 17:07 08.01.2007

� �

�


PiCCO

� Systemic vascular resistance index

� Extravascular lung water index

� Index of left ventricular contractility

� Stroke volume variation

Timestamp of last TD measurement

Global ejection fraction

Selecting a Display FormatTwo display formats are available for the bedside monitor (refer to Display Detail on page 47-4). The default setting is SMALL NUM.




• Touch PiCCO.• Select LARGE NUM or SMALL NUM.

To Print the display:

• Touch PiCCO.• Touch PRINT.


PiCCO

Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the PiCCO device or the cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the PiCCO device is powered ON.


Table 2 lists the status messages that the Flexport system interface reports for the PiCCO device during Flexport operation.




Communication between the Spacelabs Healthcare monitor and the CCO monitor has been interrupted.

YES

INJECTION ERROR Injection error on PiCCO device, check PiCCO device NO

INJECTATE TEMPERATURE SENSOR ERROR

Injectate temperature sensor error on PiCCO device, check PiCCO device

NO

INJECT FASTER THAN 10SEC Inject faster than 10 sec on PiCCO device, check PiCCO device NO

Dst (DOWNSLOPE TIME ERROR) Downslope time error on PiCCO device, check PiCCO device NO

BASELINE ERROR Baseline error on PiCCO device, check PiCCO device NO

MTt (MEAN TRANSIT TIME) CALCULATION ERROR

Mean time calculation error on PiCCO device, check PiCCO device

NO

TIME OUT (THERMODILUTION CURVE LONGER THAN 90S)

Time out on PiCCO device, check PiCCO device NO

TINJECTION > TBLOOD Tinjection > Tblood on PiCCO device, check PiCCO device NO

INVALID PCCO CALIBRATION Invalid PCCO calibration on PiCCO device, check PiCCO device NO



Radiometer TCM3

Directory of KeysTCP

TCP - MAIN MENUALARM LIMITS SETUP VIEW

ALARMS PRINT

TCP - SETUP *LARGE TXT *These keys appear on the bedside monitor only.SMALL TXT

TCP - ALARM LIMITS

PO2 PCO2 ETEMP TIMER

TCP - ALARM LIMITS - TIMERTIMER LO =

XX ↑ ↓ETEMP

ON OFF TIMER

TCP - ALARM LIMITS - ETEMPETEMP HI =

XXLO = XX ↑ ↓

ETEMPON OFF TIMER

TCP - ALARM LIMITS - PCO2PCO2 HI =

XXLO = XX ↑ ↓

PO2ON OFF PCO2

TCP - ALARM LIMITS - PO2PO2 HI =

XXLO = XX ↑ ↓

PO2ON OFF PCO2

Radiometer TCM3

Contents
OverviewThe 90438A-01 Flexport system interface enables information from a Radiometer TCM3 Transcutaneous Pressure Analyzer to be displayed on Spacelabs Healthcare monitors.




BaudRate

Character Length Parity Setting Stop Bit


Part Number

2700 7-bit odd 1 131-0789-xx (25-pin)






Radiometer TCM3


Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to the Flexport system interface, the monitor provides the following information from the analyzer.




� � � �

42.8 ETEMP

ºC4.00 TIMER

H.MIN TCP

157 PO2

mmHg

8 PCO2

mmHg

� �

� � � �

TCP

PO2 = 157mmHgPCO2 = 8 mmHgETEMP = 42.8 ºCTIMER = 4.00 H.MIN

� �

� �

� PO2 = 157mmHg TCP

� PCO2 = 8 mmHg

� ETEMP = 42.8 ºC

� TIMER = 4.00 H.MIN

� ICU - 4


Radiometer TCM3

� Electrode (sensor) temperature measured in °C

� Site timer (time remaining since the user set the analyzer up for the length of time to remain on site)

� TCP parameter key

� Transcutaneous oxygen tension (PtcO2)


� Transcutaneous carbon dioxide tension (PtcCO2)

� Patient/room ID



• the TCP key flashes,







• Touch TCP.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


• Touch TCP.• Select ALARM LIMITS.• Select an alarm parameter.• Select HI= or LO=.• Use the arrow keys to adjust.


Radiometer TCM3

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the analyzer’s parameters (refer to Figure 48-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays TCP ALM OFF to the right of the TCP key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.





• Touch TCP.• Touch VIEW ALARMS.


• Touch TCP.• Touch SETUP.• Select LARGE TXT or SMALL TXT.

PO2169

ETEMP43.3

TCP

157 PO2

mmHg60 42.7

PCO245 TIMER 8 PCO2

mmHg5 0.01


Radiometer TCM3



Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the analyzer or the cabling. If the Spacelabs Healthcare monitor displays this message, perform the following troubleshooting steps:



Table 2 lists the status messages that the Flexport system interface reports for the analyzer during Flexport operation.


• Touch TCP.• Touch PRINT.



COMMUNICATION LINK LOSTCommunication between the Flexport system interface and the analyzer has been interrupted.

Yes

SERVICE REQUIRED TCM3 electrode is defective or rejected by the analyzer. Monitor is defective. No

CALIBRATING TCM3 calibration is occurring. No


Respironics Novametrix Esprit


VENT - MENUALARM LIMITS SETUP VIEW

MODEVIEW

STATUSVIEW

ALARMS PRINT

Refer to page 49-2

VENT - SETUPLARGE TXTSMALL TXT



VENT

VENT - MENUALARM LIMITS SETUP VIEW

MODEVIEW

STATUSVIEW

ALARMS PRINT

Refer to page 49-1

VENT - ALARM LIMITS

RR VT Vmin PIP PEEP I : E APNEA SpO2*

VENT - ALARM LIMITS - SpO2SpO2 HI =

XXLO = XX

RRON OFF SpO2


XXAPNEA

ON OFF SpO2

VENT - ALARM LIMITS - I : EI : E LO =

X.XI : E

ON OFF APNEA


XXPEEP

ON OFF I : E


XXXLO = XXX

PIPON OFF PEEP

VENT - ALARM LIMITS - VminVmin LO =

XX.XVmin

ON OFF PIP

VENT - ALARM LIMITS - VTVT LO =

X.XXVT

ON OFF Vmin


XXRR

ON OFF VT

*Only SpO2 alarm limit is displayed when activated.



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Ventilator Mode History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OverviewThe 90436A-01 Flexport system interface enables information from a Respironics Novametrix Esprit ventilator to be displayed on Spacelabs Healthcare monitors.


Note:SpO2 monitoring is not supported on the Respironics Esprit ventilator. The SpO2 parameter will display with question marks (???) when the Flexport is configured to display large text.


Baud Rate

Character Length


TransitionConnector Part

Number


9600 8-bit none 1 131-1589-00 26300 Rev. E or higher









• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the DIGITAL OUTPUT connector on the ventilator.

SDLCcable

SDLCterminator

modularcable

Flexport

interface

ventilator

9-pin connectorto DIGITAL OUTPUT(back of ventilator)

SpacelabsHealthcare

monitor

system







� � � � � �

1.8I:E

21PIP

cmH2O 0PLT

cmH2O 21FiO2

% VENT

1.22VT

L

???SpO2

% 1PEEP

cmH2O8 MAP

cmH2O30.0 Vmin

L 27RR

BPM

� � � � �

� � � �

VENT

VT=1.22LRR= 27BPMPIP= 21cmH2OPEEP= 1cmH2O

� �

� � � � �

� RR= 27BPM VT= 1.22L VENT

� FiO2 = 21% PIP= 21cmH2O

� PEEP= 1cmH2O SpO2= ???

� Vmin= 30.0L MAP= 8cmH2O

� ICU 14



� Ratio of exhalation time to inspiratory time


� Inspiratory plateau pressure



� Tidal volume


Respiratory rate

Minute volume


� Positive and expiratory pressure

O2 saturation

� Patient/room ID







Note:Alarms that are generated on the Respironics Esprit ventilator will be displayed on the Spacelabs monitor within seven seconds.






• Alarm limits on the Flexport system interface can only be adjusted at the ventilator. Alarm violation is detected at the ventilator, and the Flexport system interface reports the alarm if it is turned ON for that parameter.









PIP 120 3 SpO2

0 90 VT 0.00 APNEA

20 VENT

1.22 VT

L

I : E 1.0 PEEP 0 Vmin 0.3 RR 70 27 RR

BPM



Viewing Ventilator Mode HistoryChronological history of the last eight ventilator mode settings are displayed in the waveform zone with the oldest value at the top of the left column and the most recent value at the bottom of the right column. Possible modes include CMV, SIMV, CPAP, SIMV/PS, CPAP/PS, SIMV/FB, CPAP/FB, or UNKNOWN MODE.









15:4715:47

CMVSIMV/PS

15:4915:49

SIMV/PSCMV V

ENT

1.21 VT

L15:47 CMV 15:51 CPAP/PS 25 RR

15:49 CMV 15:56 SIMV/PS BPM








Table 2 lists the status messages that the Flexport system interface reports for the ventilator during Flexport operation.







LOW PRS O2 INLET Pressure at the oxygen inlet fitting is less than 35 psig, and the O2% is 22 or greater. No


LOW BATTERY Voltage of the internal batteries is too low to sustain one hour of operation. No

EXHAL VALVE LEAK Volume of exhalation gas is less than 10% of inspiration gas. No

DISCONNECT VENT Patient service system is disconnected or plugged. No


Respironics-Novametrix 7300/7600

Directory of KeysFLOW

FLOW - MAIN MENUALARM LIMITS SETUP

FREEZE NEXTDISPLAY

VIEW ALARMS PRINT

ON OFF


FLOW - SETUP - SIZE

SIZE SWEEPSPEED

LARGE TXTSMALL TXT

FLOW - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF


mm/sec12.5

mm/sec6.25

mm/sec

FLOW - ALARM LIMITS

RR

FLOW - ALARM LIMITS - RRRR HI =

XXLO = XXON OFF



PAW

PAW - MAIN MENU

SETUPFREEZE NEXT

DISPLAY PRINTON OFF

These keys appear on the

bedside monitor only.

PAW - SETUP - SIZE

SIZE SWEEPSPEED

LARGE TXTSMALL TXT

PAW - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF

PAW - SETUP - SWEEP SPEED25

mm/sec12.5

mm/sec6.25

mm/sec



CO2


FREEZE NEXTDISPLAY

VIEW ALARMS PRINT

ON OFF


CO2 - SETUP - SIZE

SIZE SWEEPSPEED

LARGE TXTSMALL TXT

CO2 - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF

CO2 - SETUP - SWEEP SPEED25

mm/sec12.5

mm/sec6.25

mm/sec

CO2 - ALARM LIMITS

ETCO2 RR VCO2

CO2 - ALARM LIMITS - VCO2VCO2 HI =

XXLO = XXON OFF


XXLO = XXON OFF


XXLO = XXON OFF



NICO

NICO - MAIN MENUALARM LIMITS SETUP NEXT

DISPLAYVIEW

ALARMS PRINT


NICO - SETUPLARGE TXTSMALL TXT

NICO - ALARM LIMITS

C.O.

NICO - ALARM LIMITS - C.O.C.O. HI =

XXLO = XXON OFF



SPO2

SPO2 - MAIN MENUALARM LIMITS SETUP

FREEZE NEXTDISPLAY

VIEW ALARMS PRINT

ON OFF


SPO2 - SETUP - SIZE

SIZE SWEEPSPEED

LARGE TXTSMALL TXT

SPO2 - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF

SPO2 - SETUP - SWEEP SPEED25

mm/sec12.5

mm/sec6.25

mm/sec

SPO2 - ALARM LIMITS

SPO2 PR

SPO2 - ALARM LIMITS - PRPR HI =

XXLO = XXON OFF

SPO2 - ALARM LIMITS - SPO2SPO2 HI =

XXLO = XXON OFF



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Display Detail - FLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Display Detail - PAW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Display Detail - CO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Display Detail - NICO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Display Detail - SpO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
OverviewThe 90442A-03 Flexport system interface enables cardiorespiratory information from a Respironics-Novametrix Inc. Model 7300 Cardiopulmonary Management System (NICO) to be displayed on Spacelabs Healthcare monitors.

The displayed information is organized into four or five parameter sets (depending upon the mode of operation). The user can transition between these parameter sets by touching the NEXT DISPLAY key at the bedside monitor.

Note:Variables not included in the currently displayed parameter set are not trended, and their alarms are not available at the Spacelabs Healthcare monitor(s).

Configure the Novametrix Model 7300 as shown in Table 1.

Table 1: Model 7300 Configuration

Model Number


Installation Kit

Part Number


Part Number

Respironics-Novametrix

73009600 NICO firmware version 5.0 045-0158-xx 131-0686-xx

Respironics-Novametrix

76009600 NICO 2 version 10.0 045-0158-xx 131-0686-xx



Connecting the Flexport System InterfaceTo connect the Flexport system to the SDLC cable, complete the steps listed in the following Quickstart.

For information on configuring the Novametrix Model 7300 to communicate with the Flexport, refer to the Novametrix User’s Manual.

Figure 50-1: Flexport System Interface connections

The Spacelabs Healthcare monitor is now ready to display numerics. To control other interface functions, refer to the sections that follow.


• Ensure that the Spacelabs Healthcare monitoring system is shut down (power is turned OFF).



• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 9-pin serial port connector number 2 or 3 on the

Novametrix Model 7300 rear panel.• Power on the Novametrix Model 7300.

On the Novametrix Model 7300:• Press the MENU button and use the knob to select the SETUP menu and then the

INPUT/OUTPUT menu.• Select either RS232-2 or RS232-3 to match the port connection on the rear panel.• Use the knob to select FLEXPORT.• Press the knob to save.

• Configure the Novametrix Model 7300 for its intended use (for example, units of measurement or adult/neonatal mode of operations).

• Turn the power to the Spacelabs Healthcare monitoring system ON.

SDLC cable

SDLCterminator

modular cable

transition connector

Novametrix Model 730serial port 2 or 3

SpacelabsHealthcare

monitor

systemFlexport

interface



Ideally, the Novametrix Model 7300/7600 should be powered ON and fully configured prior to connecting it to the Flexport system interface.

Once the Model 7300/7600 has been connected to the Flexport system interface and is providing data to the Spacelabs Healthcare monitoring system, if the configuration needs to change, complete the following procedure:

1 Turn OFF the Spacelabs Healthcare monitoring system.

2 Reconfigure the Novametrix Model 7300/7600 monitor as needed.

3 Turn the power to the Spacelabs Healthcare monitoring system ON.

Display Detail - FLOWWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitors display the displays shown below.



� � � �

6.1 MV

L FLOW

420Vti

mL

417 VtemL15 RR

br/m

� � � �

� � �

FLOW

Vti= 420mLVte= 417mLMV=6.1LRR= 15br/m

� � � �




� Current minute volume expired (MV) value


� FLOW parameter key

� Current tidal volume inspired (Vti) value

� Current tidal volume expired (Vte) value

� Flow waveform


Patient/room ID

Display Detail - PAWWhen you touch the NEXT DISPLAY key on the bedside monitor from the FLOW Parameter screen, the monitors display the screens shown below.


� Vti= 420mL FLOW

� Vte= 417mL �� MV= 6.1L

� RR= 15br/m

ICU - 4

�

� � � �

27 Cdyn 9 MAP

cmH2O PAW

23PIP

cmH2O

4 PEEP

cmH2O15 Raw

� � �





� Current dynamic compliance (Cdyn) value

� Current mean airway pressure (MAP) value

� PAW parameter key

� Current peak inspiratory pressure (PIP) value

� Current positive end expiratory pressure (PEEP) value

� PAW waveform

� Current resistance expired (Raw) value

Patient/room ID

� �

PAW

PIP= 23cmH2OPEEP= 4cmH2O �Cdyn= 27 �Raw= 15 �

�

� �

� PIP= 23cmH2O MAP= 9cmH2O PAW

� PEEP= 4cmH2O� Cdyn= 27� Raw= 15 ICU - 4

�



Display Detail - CO2

When you touch the NEXT DISPLAY key on the bedside monitor from the PAW Parameter screen, the monitors display the screens shown below.




� Current volumetric CO2 (VCO2) value

� Current dead space to tidal volume ratio (Vd/Vt) value


� Current end-tidal CO2 (EtCO2) value

� � � � �

170VCO2

mL/m1.5 Vd/Vt

CO2

34 ETCO2

mL

23PeCO2

mmHg15 RR

br/m

� � �

� �

CO2

ETCO2= 34mmHgRR= 15br/m �

VCO2= 170mL/m �

PeCO2= 23mmHg

� �

� � �

� ETCO2= 34mmHg Vd/Vt= 1.5 CO2

� RR= 15br/m� VCO2= 170mL/m PeCO2= 23mmHg ICU - 4

�





� CO2 waveform

Current mixed expired CO2 (PeCO2) value

Patient/room ID

Note:• The VCO2 alarm is active only in Adult Respiratory Mechanics mode.

• The PeCO2 label changes to FeCO2 when units are changed to percent (%).

Display Detail - NICOWhen you touch the NEXT DISPLAY key on the bedside monitor from the CO2 Parameter screen, the monitors display the screens shown below. This screen will not display if the Novametrix Model 7300 is in the respiratory mechanics mode. The SPO2 screens will display instead.



� � � � � �

82SV 2.1Cl 4.6PCBF NICO

5.3 C.O.

L/minmL L/min

�

� � ��

NICO

C.O. =5.3L/minPCBF=4.6L/minCl=2.1 �

SV=82mL




� Current stroke volume (SV) value

� Current cardiac index (CI) value

� Current pulmonary capillary blood flow (PCBF) value

� NICO parameter key

� Current cardiac output (C.O.) value

Note:This is the average cardiac output, irrespective of C.O. Mode on the NICO monitor.


� Patient/room ID

Display Detail - SpO2

When you touch NEXT DISPLAY on the bedside monitor from the CO2 (if in respiratory mechanics mode) or NICO Parameter screen, the monitors display the screens shown below.


� � � �

� C.O.= 5.3L/min Cl= 2.1 NICO

� SV= 82mL PCBF= 4.6L/min

� ICU - 4

� � �

SPO2

98 SpO2

%

70 PR

bpm

� � �




Figure 50-16: Central monitor, split screen display


� Current oxygen saturation (SpO2) value


� Current pulse rate (PR) value

� SpO2 waveform

� Patient/room ID

� �

SPO2

SpO2= 98%

PR= 70bpm

� � �

� �

� SpO2 = 98% SPO2

� PR = 70bpm

� ICU - 4�





• the main parameter key flashes,




Note:• Alarm limits on the Flexport system interface can only be adjusted at the Novametrix Model 7300.

• Turning Flexport system interface alarms ON or OFF at the Spacelabs Healthcare monitor(s) does not affect alarms on the Novametrix Model 7300.

• Alarm violation is detected at the Novametrix Model 7300, and the Flexport system interface reports the alarm if it is turned ON for that parameter. When the alarming parameter is enabled and displayed on the currently active display or channel, the alarm response described above takes place. When the alarming parameter is enabled and NOT displayed on the currently active display or channel, the Spacelabs Healthcare monitor(s) displays an ALARM VIOLATION status message in the waveform zone.


• Touch the main parameter key.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.



Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for respiration rate (RR), EtCO2, VCO2, CO, SpO2, and pulse rate (refer to Figure 50-17). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays ALM OFF to the right of the parameter key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.

Figure 50-17: View Alarms screen, SpO2 example


Turning Waveforms ON/OFFYou can turn waveforms OFF and display only the numeric values. When waveforms are OFF, the SIZE ↑ and SIZE ↓ keys, the SWEEP SPEED key, and the FREEZE ON/OFF keys are disabled.



• Touch the main parameter key.• Touch VIEW ALARMS.


• Touch the main parameter key.• Touch SETUP.• Touch SIZE.• Select WAVEFORM ON/OFF.

SpO2100 S

PO2

98 SpO2

%85

PR180

40 70 PR

bpm





Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 25, 12.5, and 6.25 mm/second.

The default setting is 25 mm/second for SpO2 and 12.5 mm/second for all others.

Selecting a Display FormatTwo display formats are available for the bedside monitor (refer to the Display Detail sections on pages page 50-9 through page 50-14).

The default setting is LARGE TEXT.


• Touch the main parameter key.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.


• Touch the main parameter key.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.


• Touch the main parameter key.• Touch SETUP.• Select LARGE TXT or SMALL TXT.







printout.


Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the Novametrix Model 7300 or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the Novametrix Model 7300 is powered ON.


The Novametrix Model 7300 sends six different status messages to the Flexport, depending upon the parameter set displayed. There are no visible or audible alarm indications associated with the display of these messages.


• Touch the main parameter key.• Select FREEZE ON.


• Touch the main parameter key.• Touch PRINT.



Table 2 lists the status messages that the Flexport system interface reports for the Novametrix Model 7300 during Flexport system interface operation.

Note:Additional messages display on the Novametrix Model 7300 that are not sent to the Flexport for display on the Spacelabs Healthcare monitor(s).


Message Text Parameter Set Display Zone Indication

FLOW DISCONNECT FLOW, PAW, NICO Waveform Flow sensor is disconnected.

CO2 DISCONNECT CO2, NICO Waveform CO2 sensor is disconnected.

SPO2 DISCONNECT SpO2 Waveform SpO2 sensor is disconnected.

CHECK NICO MESSAGE All Prompt

An informational message (other than Alert Limit Violations) is active at the Model 7300.

DEMO MODE DATA All Waveform Model 7300 is in DEMO mode.

ALARM VIOLATION All WaveformA parameter not in the current parameter set is in Alarm state.


Respironics Novametrix 840/860

Directory of Keys

TCP

TCP - MAIN MENU

ALARM LIMITS SETUP VIEW

ALARMS PRINT

TCP - SETUP LARGE TXT

SMALL TXT

TCP - ALARM LIMITS

PCO2 PO2 ETEMP

TCP - ALARM LIMITS - ETEMPETEMP HI =

X.XLO = X.X ↑ ↓

ON OFF

TCP - ALARM LIMITS - PO2PO2 HI =

X.XLO = X.X ↑ ↓

PCO2

ON OFF PO2

TCP - ALARM LIMITS - PCO2PCO2 HI =

X.XLO = X.X ↑ ↓

PCO2

ON OFF PO2



Contents
OverviewThe 90438A-02 Flexport system interface enables information from a Respironics Novametrix Transcutaneous Pressure (TCP) Analyzer to be displayed on Spacelabs Healthcare monitors.

Configure the TCP analyzer as shown in Table 1. Verify that the RS-232 serial port of the TCP analyzer is configured for Terminal Mode operation. Once in this mode, MODE 0 must be selected. Refer to the TCP analyzer manual for additional configuration setup procedures.

Table 1: TCP Analyzer Configuration

Novametrix Model Number

Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number

Respironics Novametrix 840 9600 8 bit none 1 131-0687-xx

(25-pin)

Respironics Novametrix 860 9600 8 bit none 1 131-0946-xx

(25-pin)



Connecting the Flexport System InterfaceTo connect the Flexport system interface to the TCP analyzer, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the TCP analyzer. To control other interface functions, refer to the sections that follow.

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the TCP analyzer.






• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector on the TCP analyzer.

� � �

42.8 ETEMPTCP

157 PCO2

oC mmHg

8 PO2

mmHg

� �

� � �

TCP

PCO2 = 157 mmHgPO2 = 8 mmHgETEMP = 42.8oC

� �




� Electrode (sensor) temperature measured in °C

� TCP parameter key

� Transcutaneous carbon dioxide tension (PtcCO2)


� Transcutaneous oxygen tension (PtcO2)

� Patient/room ID



• the TCP key flashes,



When all parameter alarms are turned OFF, status alarms will still cause the TCP key to flash.


Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the TCP

analyzer.

• Alarm tones on the TCP analyzer can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.


• Touch TCP.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.

� �

� PCO2 = 157 mmHgTCP

� PO2 = 8 mmHg

� ETEMP = 42.8oC

� ICU 14



Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the TCP analyzer’s parameters (refer to Figure 51-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays TCP ALM OFF to the right of the TCP key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.




• Touch TCP.• Select ALARM LIMITS.• Select an alarm parameter.• Touch HI= or LO=.• Use arrow keys to adjust.


• Touch TCP.• Touch VIEW ALARMS.


• Touch TCP.• Touch SETUP.• Select LARGE TXT or SMALL TXT.

PCO2 199 ETEMP 50.0 TCP

PCO2 = 157 mmHg0 0 PO2 = 8 mmHg

PO2 990 ETEMP = 42.8oC0








Table 2 lists the status messages that the Flexport system interface reports for the TCP analyzer during Flexport system interface operation.


• Touch TCP.• Touch PRINT.



COMMUNICATION LINK LOST Communication between the TCP analyzer and the monitor has been interrupted. Yes

CALIBRATION REQUIRED Analyzer requires calibration. No







ON OFF

CO2 - SETUP

SIZE SWEEPSPEED

LARGE TXTSMALL TXT

CO2 - SETUP - SIZE CO2 - SETUP - SWEEP SPEEDWAVEFORM

↑ ↓25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/secON OFF

CO2 - ALARM LIMITS

APNEA RR ETCO2




XXLO = XX ↑ ↓

APNEAON OFF RR

CO2 - ALARM LIMITS - APNEAAPNEA HI =

XXLO = XX ↑ ↓

APNEAON OFF RR


Contents
OverviewThe 90433A-01 Flexport system interface enables information from a Respironics Novametrix 1260/1265 analyzer to be displayed on Spacelabs Healthcare monitors.

Configure the analyzer as shown in Table 1. Consult the appropriate analyzer manual for additional configuration setup procedures.


Analyzer Name and Model Number

Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number


Respironics Novametrix 1260 9600 8-bit none 1 131-0684-xx (25-pin) H:eng-1260-86

Respironics Novametrix 1265 9600 8-bit none 1 131-0684-xx (25-pin) eng-1265-18












� �

CO2

51 ETCO2

mmHg

14 RR

BPM

� �

� � �

CO2

ETCO2 = 51 mmHgRR = 14 BPM

�




� ETCO2 parameter key

� Current EtCO2 value




� Patient/room ID












� � �

� ETCO2 = 51 mmHg APNEA = 20s C

O2

� RR = 14 BPM

� ICU 14






• Touch CO2.• Select ALARM LIMITS.• Select an alarm parameter.• Select HI= or LO=.• Use the arrow keys to adjust.



ETCO2 5530 C

O2

49 ETCO2

mmHg

APNEA 20 RR 28 12 RR

8 BPM




Turning Waveforms ON or OFFYou can turn the waveform OFF and display only numeric values. When waveforms are OFF, the SWEEP SPEED key, the FREEZE ON/OFF keys, and the size keys are disabled.


























printout.












AIR CAL ERROR Airway zero calibration error — retry airway zero. Yes

CAPNOMETER FAULTY Monitor hardware error, monitor faulty — do not use. Yes

CHECK AIRWAY ADAPTER Sensor not properly connected to airway adapter or calibration cells. No

COMMUNICATION LINK LOST Communication with the gas analyzer is interrupted. Yes

MONITOR ERROR 1 Monitor faulty, do not use — contact qualified service personnel. Yes


NO UP TO TEMP The analyzer has not completed its warm-up. No

RS232 ERROR Communication between the analyzer and the analyzer’s RS232 port is faulty. Yes

RECALIBRATE SENSORMonitor has detected that the sensor signals have changed since the analyzer was calibrated — recalibrate the sensor.

No

SENSOR FAULTY Sensor faulty — do not use, replace sensor. Yes

SENSOR OVER-TEMP Sensor faulty — do not use, replace sensor. No

SENSOR UNPLUGGED Sensor not connected to monitor — connect it.Sensor or sensor cable faulty — replace sensor. No

SPAN CAL ERROR Calibration error — retry calibration. Yes

ZERO CAL ERROR Calibration error — retry calibration. Yes



Respironics Novametrix 2001

Directory of Keys

SPO2

SPO2 - MAIN MENUALARM LIMITS SETUP


ON OFF

SPO2 - SETUP

SIZE SWEEPSPEED

LARGE TXTSMALL TXT

SPO2 - SETUP - SIZE SPO2 - SETUP - SWEEP SPEEDWAVEFORM SIZE

↑SIZE

↓50

mm/sec25

mm/sec12.5

mm/sec6.25

mm/secON OFF

SPO2 - ALARM LIMITS

SPO2 PR

SPO2 - ALARM LIMITS - PRRR HI =

XXLO = XXON OFF

SPO2 - ALARM LIMITS - SPO2SPO2 HI =

XXLO = XXON OFF



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Viewing the Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OverviewThe 90442A Flexport system interface enables information from a Respironics Novametrix 2001 Pulse Oximeter to be displayed on Spacelabs Healthcare monitors.



Baud Rate




Part Number

9600 Respironics Novametrix 2001; V 2.1 045-0156-xx 131-0946-xx

(25 pin)











• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 25-pin connector on the pulse oximeter serial port.

� � �

5.6 SIG SpO2

98 SPO2

%

70 RR

bpm

� �

� �

SpO2

SPO2= 98%

PR= 70bpm

SIG= 5.6

� � �




� Current signal strength value





� Patient/room ID

Enabling AlarmsThe Alarm Limits menu allows you to enable alarm limits for SpO2. When an alarm is turned ON and the parameter value exceeds an alarm limit, all of the following occur:





When both parameter alarms are turned OFF, alarm status messages will still cause the SPO2 key to flash.


Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the pulse

oximeter.

• Alarm limits can only be adjusted at the pulse oximeter. Alarm violation is detected at the pulse oximeter, and the Flexport system interface reports the alarm if it is turned ON for that parameter.


� �

� SPO2 = 98% SPO2

� PR = 70bpm� SIG = 5.6

� ICU 14



Viewing the Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the pulse oximeter’s parameters (refer to Figure 53-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays SPO2 ALM OFF to the right of the SPO2 key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.



• Touch SPO2.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.



SPO2 100 SpO2

98 SPO2

85 %

PR 180 70 RR

40 bpm




Turning Waveforms ON or OFFYou can turn waveforms OFF and display only the numeric values. When waveforms are OFF, the SIZE ↑ and SIZE ↓ keys, the SWEEP SPEED key, and the FREEZE ON/OFF keys are disabled.










Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 50, 25, 12.5, and 6.25 mm/second.











• Touch SPO2.• Select FREEZE ON.





printout.



• Verify that the oximeter is powered ON.


Note:When powering OFF the pulse oximeter with all cables attached, do NOT power the pulse oximeter back ON until after the Flexport channel has disappeared from the Spacelabs Healthcare monitor (approximately one minute).





Contents
OverviewThe 90434A-03 Flexport system interface enables information from a Respironics Novametrix 7000/7100 analyzer to be displayed on Spacelabs Healthcare monitors.

Configure the analyzer as shown in Table 1. Consult the appropriate analyzer manual for additional configuration setup procedures.

To complete the configuration, set the analyzer to send CO2 waveform data (Tele-Cap/Spacelabs) from the RS-232 port. If the analyzer is configured to send SpO2 waveform data (Tele-Sat/Spacelabs), the Spacelabs Healthcare monitor will display the message COMMUNICATION ERROR – CALL SERVICE and cease processing analyzer information.


Analyzer Name and Model Number

Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number


Respironics Novametrix Model 7000 9600 8-bit none 1 131-0684-xx

(25-pin) H: eng-1260-83

Respironics Novametrix Model 7100: CO2SMO 9600 8-bit none 1 131-0684-xx

(25-pin) Eng-7100-1699











� � � �

21 RR PO+ET

24 ETCO2

BPM mmHg

97SPO2

%

�







� Current EtCO2 (mmHg) value




� Patient/room ID






When all parameter alarms are turned OFF, status alarms still cause the PO+ET key to flash.


� �

PO+ET

ETCO2 = 24 mmHg

SPO2 = 97%

RR = 21 BPM

� � �

� �

� ETCO2 = 24mmHg PO+ET

� SPO2 = 97%

� RR = 21 BPM

� APNEA = 20 sec

� ICU 14






• Touch PO+ET.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


• Touch PO+ET.• Select ALARM LIMITS.• Select an alarm parameter.• Select HI= or LO=.• Use the arrow keys to adjust.



Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the analyzer’s parameters (refer to Figure 54-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays PO+ET ALM OFF to the right of the PO+ET key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.



Turning Waveforms ON or OFFYou can turn waveforms OFF and display only the numeric values. When waveforms are OFF, the SWEEP SPEED key, the FREEZE ON/OFF keys, and the size keys are disabled.





RR 40 EtCO275 P

O+ET

24 ETCO2

10 50 mmHg

APNEA 20 SpO2100 97

SPO2

85 %




















printout.



• Touch PO+ET.• Select FREEZE ON.











AIR CAL ERROR Airway zero calibration error — retry airway zero. Yes

CAPNOMETER FAULTY Monitor hardware error, monitor faulty — do not use. Yes

CHECK AIRWAY ADAPTER Sensor not properly connected to airway adapter or calibration cells. No

COMMUNICATION ERROR — CALL SERVICE

The analyzer RS-232 port output is incorrectly configured. The analyzer is set to send SpO2 waveform data (Tele-Sat/Spacelabs) instead of CO2 waveform data (Tele-Cap/Spacelabs) from the RS-232 port. The monitor displays this message for approximately 20 seconds, then displays COMMUNICATION LINK LOST.

No

COMMUNICATION LINK LOST Communication between the analyzer and the monitor has been interrupted. Yes

CONNECT 87XX PROBE Connect sensor — if sensor is connected, replace, do not use. Yes

INSUFFICIENT LIGHTTissue between sensor LEDs and photo-diode is too thick or opaque to allow adequate light transmission.

Yes

LIGHT INTERFERENCE Ambient light interference (i.e., warming lights, direct sunlight). Yes

LOW SIGNAL STRENGTH Pulsatile signal too weak for proper sensor operation. Yes





PROBE ERROR 1 Sensor faulty, do not use — replace sensor. Yes

PROBE ERROR 2 Sensor faulty, do not use — replace sensor. Yes

PROBE FAILURE Sensor faulty, do not use — replace sensor; also refer to UNIDENTIFIED PROBE. Yes

PROBE OFF PATIENT

Sensor dislodged from patient, improperly applied, or placed on an area too translucent for proper sensor operation — reposition sensor.

Yes

PULSE OUT OF RANGE Detected pulse rate is less than 30 bpm or greater than 250 bpm. No

RS232 ERROR Communication between the analyzer and the monitor has been interrupted. Yes

RECALIBRATE SENSORMonitor has detected that the sensor signals have changed since the analyzer was calibrated — recalibrate the sensor.

No

SENSOR FAULTY Sensor faulty — do not use, replace sensor. Yes

SENSOR OVER-TEMP Sensor faulty — do not use, replace sensor. No

SENSOR UNPLUGGEDSensor not connected to monitor — connect it.Sensor or sensor cable faulty — replace sensor.

No

SPAN CAL ERROR Calibration error — retry calibration. Yes

UNIDENTIFIED PROBE

Monitor cannot determine if sensor is of correct type (87xx series). May appear if attached to a thick tissue site when sensor is first plugged into monitor.

Yes

ZERO CAL ERROR Calibration error — retry calibration. Yes




SenTec Digital Monitor

Directory of Keys (with PCO2/SpO2/PR parameters enabled on SenTec device)

SDM

SDM - MENUALARM LIMITS SETUP


ON OFF


SDM - SETUP

SIZE SWEEP SPEED

LARGE TXTSMALL TXT

SDM - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF

SDM - SETUP - SWEEP SPEED50

mm/sec25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec0.78

mm/sec0.39

mm/sec

SDM - ALARM LIMITS

PCO2 SPO2 PR

SDM - ALARM LIMITS - PRPR HI =

XXLO = XXON OFF

SDM - ALARM LIMITS - SpO2SPO2 HI =

XXLO = XXON OFF

SDM - ALARM LIMITS - PCO2PCO2 HI =

XXLO = XXON OFF

Flexport System Interface SenTec Digital Monitor 55-1


Directory of Keys(with only PCO2 parameter enabled on SenTec device)

SDM

SDM - MENUALARM LIMITS SETUP VIEW

ALARMS PRINT


SDM - SETUPLARGE TXTSMALL TXT

SDM - ALARM LIMITS

PCO2

SDM - ALARM LIMITS - PCO2PCO2 HI =

XXLO = XXON OFF



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
OverviewThe 90442A-03 Flexport system interface enables information from a SenTec Digital Monitor (SDM) to be displayed on Spacelabs Healthcare monitors.

Configure the SDM as shown in Table 1. Consult the SDM manual for additional configuration setup procedures.

Table 1: SenTec Digital Monitor Configuration

Baud Rate




9600 v06.10 045-0162-xx 131-1972-xx(9 pin)



Connecting the Flexport System InterfaceTo connect the Flexport system interface to the SDM, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the SDM. To control other interface functions, refer to the sections that follow.

Note:During the warm-up phase, the PCO2 values display in grey on the device and the monitor displays question marks (???). Once the device is sufficiently warmed up, PCO2 values will display normally.

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the SDM.

Figure 56-1: Bedside monitor, large text screen with PCO2/SpO2/PR enabled




• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 9-pin connector on the back of the SDM serial

port.

� � � �

41.9STempºC 85

PR

bpm SDM

31.8 PCO2

mmHg

99 SPO2

%7.8 STimehours

� � �



Figure 56-2: Bedside monitor, large text screen with only PCO2 enabled

Figure 56-3: Bedside monitor, small text screen with PCO2/SpO2/PR enabled

Figure 56-4: Bedside monitor, small text screen with only PCO2 enabled

Figure 56-5: Central monitor, split screen with PCO2/SpO2/PR enabled

� � �

41.9 STempºC S

DM

31.8 PCO2

mmHg

7.8 STimehours

� �

� � �

SDM

PCO2= 31.8mmHg

SPO2= 99%

PR= 85bpm

STemp= 41.9ºC

� � �

� �

SDM

PCO2= 31.8mmHg

STemp= 41.9ºC

� �

� � �

� PCO2 = 31.8mmHg SDM

� SPO2 = 99%

� STemp = 41.9ºC PR = 85bpm

� STime = 7.8 hours

SL370

�



Figure 56-6: Central monitor, split screen with only PCO2 enabled

� SDM parameter key

� Current PCO2 (transcutaneous carbon dioxide tension) value

� Current SpO2 (oxygen saturation) value

� Current PR (pulse rate) value

� Current STemp (sensor temperature measured in ºC) value

� Current STime (site timer countdown clock) value


Patient/room ID



• the SDM key flashes,



When all parameter alarms are turned OFF, alarm status messages will still cause the SDM key to flash.


Note:• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the SDM.

• Alarm limits can only be adjusted at the SDM. Alarm violation is detected at the SDM, and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• Alarm tones on the SDM can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.

�

� PCO2 = 31.8mmHg SDM

� STemp = 41.9ºC

� STime = 7.8 hours

SAT1

�



Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the SDM’s parameters (refer to Figure 56-7, Figure 56-8, Figure 56-9, and Figure 56-10). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays SDM ALM OFF to the right of the SDM key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.

Figure 56-7: View Alarms screen, large text, PCO2/SpO2/PR enabled

Figure 56-8: View Alarms screen, small text, PCO2/SpO2/PR enabled

To turn alarms ON or OFF from the Spacelabs Healthcare monitor:

• Touch SDM.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


• Touch SDM.• Touch VIEW ALARMS.

PCO2 45.02.0 PR

14540 S

DM

31.8PCO2

mmHg

99SPO2 10070

SpO2

%

PCO2 45.02.0

PR 14540 S

DM

PCO2= 31.8mmHg

SPO2= 99%

SPO2 10070

PR= 46bpm

STemp= 42.0ºC



Figure 56-9: View Alarms screen, large text, only PCO2 enabled

Figure 56-10: View Alarms screen, small text, only PCO2 enabled




When PCO2 is the only parameter enabled on the SDM device, the WAVEFORM ON/OFF key, the SWEEP SPEED key, and the FREEZE ON/OFF keys are not displayed on Spacelabs Healthcare monitors.


• Touch SDM.• Touch SETUP.• Touch SIZE.• Select WAVEFORM ON/OFF.

PCO2 45.0 SDM

31.8 PCO2

2.0 mmHg

PCO2 45.02.0 S

DM

PCO2= 31.8mmHg

STemp= 42.0ºC





Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 50, 25, 12.5, 6.25, 3.12, 1.56, 0.78, and 0.39 mm/second.





• Touch SDM.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.


• Touch SDM.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.


• Touch SDM.• Touch SETUP.• Select LARGE TXT or SMALL TXT.







printout.


Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the SDM or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the SDM is powered ON.


Note:• When powering OFF the SDM with all cables attached, do NOT power the SDM back ON until after the

Flexport channel has disappeared from the Spacelabs Healthcare monitor (approximately one minute).


• Touch SDM.• Select FREEZE ON.

To print the SDM display:

• Touch SDM.• Touch PRINT.



Table 2 lists the status messages that the Flexport system interface reports for the SenTec Digital Monitor during Flexport system interface operation.



MONITOR FAULT Monitor faulty, do not use — contact qualified service personnel. Yes

CONNECT SENSOR Sensor is not detected — if sensor is connected, replace, do not use. Yes

SENSOR FAULTThe system detected a severe sensor fault. Sensor is shut down — do not use, replace sensor.

Yes

TEMP. LIMITER ACTIVE Temperature surveillance detected a temperature problem. Yes

GAS LEAK IN DOCKING STATIONDocking station (DS) surveillance detected a leak in the DS chamber (for example, polluted by sensor gel).

Yes

SENSOR OFF PATIENT The sensor was dropped or is removed from the patient and calibration is needed. Yes

CALIBRATE SENSOR Sensor is removed from the docking station and calibration is needed. Yes

DOCKING STATION FAULTDocking station surveillance detected a severe DS fault (for example, the gas pressure too high).

Yes

GAS BOTTLE EMPTY Gas bottle on the docking station is empty. Yes

SPO2 STABILIZING SpO2 and pulse rate are not stable. No

LOW SIGNAL Low pulse signal. No

MOTION ARTIFACT Motion artifact detected. No

SITE TIME ELAPSED Check measurement site, and if necessary, relocate the sensor to prevent skin irritation. Yes

REMEMBRANCE SENSOR The sensor needs to be remembrance. Yes

BATTERY LOWBattery capacity is low (<10%) while the power supply cable is unplugged or the power supply is plugged in and charging.

Yes

PCO2 STABILIZINGPCO2 measurement is not yet stable after sensor application. PCO2 values do not yet reflect patient data.

No



READY FOR USE Ths sensor is removed from the docking station and calibration is NOT needed No





Smiths Graseby 3000

Directory of Keys

IV

IV - MAIN MENU

SETUP PRINT

IV - SETUP MENU

PUMP A WEIGHT CHANGE CONFIG




7 8 9

4 5 6

1 2 3

0 . CLEAR ENTER

IV - PUMP A MENUPRIMARY SELECT

DRUGSELECT CONC.

SELECT DILUENT

DOSE CALCS

ALARMS

SECONDARY ON OFF

Smiths Graseby 3000

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Disconnecting a Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
OverviewThe 90437A-08 Flexport system interface enables information from a Smiths Graseby 3000 volumetric infusion pump to be displayed on Spacelabs Healthcare monitors.

Configure the infusion pump as shown in Table 1. Consult the infusion pump manual for additional configuration setup procedures.

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the infusion pump, complete the steps listing in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the pump. To control other interface functions, refer to the sections that follow.


Baud Rate

Character Length


9600 7-bit odd 1




• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the connector on the infusion pump communications

port.


Smiths Graseby 3000

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the pump.



� Pump address

� Selected medication or fluid (until you set up the drug or fluid for each pump, this field displays * * * * * * * *)



• The pump started a new dose

• The pump rate was titrated

• The pump changed from secondary to primary or from primary to secondary



� � � � � �

PUMP DRUG/FLUID RATE VOL. INFUSED PUMP STATUSA DOPAMINE 10.0 mcg/kg/min 122.1 ml I

VA PUMPING

� � � �

PUMP DRUG/FLUID STATUSA DOPAMINE PUMPING I

V


Smiths Graseby 3000

Entering Setup InformationSetup information is necessary for the monitor to display the drug (or fluid) names and to compute the medication and calculated pump rates. You can control the following functions from the Setup menu:
















• Touch IV.• Select SETUP.• Touch PUMP.• Touch ALARMS ON/OFF.


Smiths Graseby 3000






• Touch IV.• Select SETUP.• Touch PUMP.• Touch PRIMARY/SECONDARY.



LR lactated ringers




D5 1/2NS 20KCL 5% dextrose with 0.45% saline and 20 mEq potassium chloride/liter


PUMP A - SELECT FLUID


LR

D5 1/2NS 20KCL

D10 1/2NS

1/2 NS

D5 LR

D5 1/4NS

D10 1/4NS

1/4NS

D5 NS

D5W

D10W

TPN

D5 1/2NS

D10 NS

NS

LIPIDS


Smiths Graseby 3000






NS 0.9% saline

1/2 NS 0.45% saline

1/4 NS 0.2% saline




• Touch IV.• Select SETUP.• Touch PUMP.• Touch SELECT FLUID.• Select a fluid from the list (or touch PAGE↓, then select a fluid).• Touch ENTER.




Smiths Graseby 3000




PUMP A - SELECT DRUGAMINOPHYLLINE AMRINONE BRETYLIUM DOBUTAMINE




ENTER

To select a drug:

• Touch IV.• Select SETUP.• Touch PUMP.• Touch SELECT DRUG.• Select a drug from the list.• Touch ENTER.


Smiths Graseby 3000

Select the Drug ConcentrationThe drug concentration represents the amount of a drug dissolved in a volume of diluent. The Flexport system interface saves the last entered default concentration values and unit of measurement associated with the selected drug.


To change a value after you have completed an initial drug/fluid entry, complete all the steps listed in the Quickstart on page 57-10. Figure 57-5 illustrates the Concentration screen.



system.


PUMP A - ENTER DRUG QTY, UNITS, AND VOLUME. CONCENTRATION = _______

7 8 9 mcg mg /50 ml /100 ml

4 5 6 g ml /250 ml /500 ml


0 . CLEAR ENTER


Smiths Graseby 3000






If you have completed an initial drug/fluid entry and wish to change a value, complete all of the steps listed in the Quickstart on page 57-11.

Note:If the Flexport system interface displays an initial VOLUME INFUSED for the pump you intend to use, you must clear that value at the pump before you start an infusion. Otherwise, the Flexport system interface will appear to add the volume infused from the previous infusion to the current infusion (either primary or secondary).


• Touch IV.• Select SETUP.• Touch PUMP.• Touch SELECT CONC.• Enter the drug quantity.• Select the unit of measurement.• Select the volume of fluid.• Touch ENTER.


• Touch IV.• Select SETUP.• Touch PUMP.• Touch SELECT DILUENT.• Choose a diluent from the list (or touch PAGE , then select a diluent).• Touch ENTER.


Smiths Graseby 3000






PUMP A - ENTER DRUG QUANTITY, UNITS, AND TIME. DOSE = _______



1 2 3 units mEq



• Touch IV.• Select SETUP.• Touch PUMP.• Touch DOSE CALCS.• Enter the dose quantity.• Enter unit of measurement.• Enter the time unit.• Touch ENTER.


Smiths Graseby 3000



After you complete your editing and touch ENTER, the current weight will appear in the appropriate displays. You can enter up to six characters, including the decimal point. The valid weight range is from 1 to 250 kg (2 to 551 pounds). The interface saves the weight so you can use it in the Dose Calcs screen with the mcg/kg and mg/kg units of measurement.


7 8 9

4 5 6

1 2 3

0 . CLEAR ENTER




Smiths Graseby 3000









CHANGE NAME


Smiths Graseby 3000

Figure 57-9: Change Drug Name screen









0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J

K L M N O P Q R S T

U V W X Y Z / % .



Smiths Graseby 3000

Disconnecting a PumpWhen you disconnect the pump from the Flexport system, the Flexport system interface discontinues the infusion record.




• Touch IV.• Select SETUP• Touch CHANGE CONFIG.• Touch EDIT DRUG or EDIT FLUID.• Select the name you want to change.• Touch CHANGE NAME.• Use the alphanumeric keys to make necessary changes.• Touch ENTER.

To disconnect a pump, detach the modular cable connecting the Flexport to the pump at either end.




Smiths Graseby 3000





Note:When the pump is in alarm for On Hold, the displayed status message is PUMP ALARM. Touching the SILENCE key on the pump causes the pump to transition from the alarm state to the hold state. The monitor reflects this by displaying a status of STOPPED.



DISCONNECTED Pump has been disconnected.



STOPPED Pump is in hold state or turned OFF.




LOW BATTERY Pump battery requires recharging.

OCCLUSION Closed clamp, kinked, occluded tubing, or occluded filter detected.




Tyco Nellcor N-395/N-595/N-600

Directory of Keys

SPO2

SpO2 - MAIN MENUALARM LIMITS SETUP


ON OFF


SpO2 - SETUP

SIZE SWEEP SPEED

LARGE TXTSMALL TXT

SpO2 - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF

SpO2 - SETUP - SWEEP SPEED50

mm/sec25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec0.78

mm/sec0.39

mm/sec

SpO2 - ALARM LIMITS

SPO2 PR

SpO2 - ALARM LIMITS - PRPR HI =

XXLO = XXON OFF


XXLO = XXON OFF


Contents
OverviewThe 90442A Flexport system interface enables information from a Tyco Nellcor N-395, N-595, or N-600 pulse oximeter to be displayed on Spacelabs Healthcare monitors.



Baud Rate




9600N-395: V 1.8.0.0N-595: V 3.3.0.0N-600: V 1.1.2.0

045-0151-xx 131-1725-xx (15 pin)




Note:When powering OFF the equipment, power OFF the Nellcor pulse oximeter or disconnect the Flexport before powering OFF the Spacelabs Healthcare monitor. Failure to do so may cause the Nellcor pulse oximeter to reset. If, after a monitor reset or power sequence, the Flexport does not start updating information, disconnect the Flexport from the back of the monitor and reconnect to establish communications.







• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 15-pin connector on the pulse oximeter serial

port.

� �

SpO2

98SpO2

%

70 PR

bpm

� �





� SpO2 parameter key




� Patient/room ID

Enabling AlarmsThe Alarm Limits menu allows you to enable alarm limits for SpO2 and pulse rate. When an alarm is turned ON and that parameter value exceeds an alarm limit, all of the following occur:


• the SpO2 key flashes,



When all parameter alarms are turned OFF, alarm status messages will still cause the SpO2 key to flash.


� �

SpO2

SpO2= 98%

PR= 70bpm

� �

� �

� SpO2 = 98% SpO2

� PR = 70bpm

� ICU - 4



Note:• Turning Flexport system interface alarms ON or OFF does not affect alarms settings on the pulse

oximeter.

• Alarm limits can only be adjusted at the pulse oximeter. Alarm violation is detected at the pulse oximeter and the Flexport system interface reports the alarm if it is turned ON for that parameter.


Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the pulse oximeter’s parameters (refer to Figure 58-4). If alarms for both parameters are turned OFF, the Spacelabs Healthcare monitor displays SPO2 ALM OFF to the right of the SpO2 key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.



• Touch SpO2.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.


• Touch SpO2.• Touch VIEW ALARMS.

SpO2 100 SpO2

98SpO2

85 %

PR 180 70 PR

40 bpm









• Touch SpO2.• Touch SETUP.• Touch SIZE.• Select WAVEFORM ON/OFF.


• Touch SpO2.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.










• Touch SpO2.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.


• Touch SpO2.• Touch SETUP.• Select LARGE TXT or SMALL TXT.


• Touch SpO2.• Select FREEZE ON.





printout.


Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the pulse oximeter or cabling. If the monitor displays this message, perform the following troubleshooting steps:



Note:When powering OFF the pulse oximeter with all cables attached, do NOT power the pulse oximeter back ON until after the Flexport channel has disappeared from the Spacelabs Healthcare monitor (approximately one minute).


• Touch SpO2.• Touch PRINT.


Tyco Nellcor N-1000

Contents
OverviewThe 90434A-02 Flexport system interface enables information from a Tyco Nellcor N-1000 analyzer to be displayed on Spacelabs Healthcare monitors.



Baud Rate

Character Length

Parity Setting

Stop Bit


Part Number


9600 8-bit none 1 131-0686-xx (9-pin) 02.03.03


Tyco Nellcor N-1000










� � � � �

40 N2O 21 RR PO+ET

24 ETCO2

% BPM mmHg

83 PR 97 SPO2

bpm %

� �

� � �

PO+ET

ETCO2= 24mmHg

SPO2 = 97%RR = 21BPMN2O= 40%

� � �


Tyco Nellcor N-1000


� Current nitrous oxide value*



� Current ETCO2 (mmHg) value




Apnea monitoring status (displays ON or OFF)

Patient/room ID

*The N2O display is ON when the N2O value from the analyzer is greater than 2% or when the N2O alarm limit key is turned ON.









• Touch PO+ET.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.

� � �

� ETCO2= 24mmHg N2O = 40% PO+ET

� RR = 21BPM APNEA = 20S

� PR = 83bpm

� SPO2 = 97%

ICU 14


Tyco Nellcor N-1000


• When the Apnea alarm is turned ON, it is fixed at 20 seconds.





• Select HI= or LO=.• Use the arrow keys to adjust.



N2O 70 RR 40 ETCO2 55 PO+ET

24 ETCO2

20 10 25 mmHg

APNEA 20 PR 110 BPM 100 97 SPO2

50 70 %


Tyco Nellcor N-1000









Tyco Nellcor N-1000







COMMUNICATION LINK LOST Communication between the analyzer and the monitor has been interrupted. Yes

CO2-ZERO CALIBRATIONThe analyzer is calibrating (occurs after you initiate analyzer calibration function or periodically during automatic self-calibration).

No

GAS SYSTEM DISABLED Gas system is disabled (occurs after you touch the analyzer DISABLE button). No

GAS SYSTEM PURGING Gas system is purging (occurs when you touch the analyzer START PURGE button). No


Tyco Nellcor N-2500


GAS - MAIN MENUALARM LIMITS SETUP VIEW

ALARMS PRINT

GAS - SETUP MENULARGE TXTSMALL TXT

GAS - ALARM LIMITS

RR ETCO2 SPO2 PR N2O

GAS - ALARM LIMITS - N2ON2O HI =


GAS - ALARM LIMITS - PRPR HI =

XXLO = XX ↑ ↓

SPO2ON OFF PR

GAS - ALARM LIMITS - SPO2SPO2 HI =

XXLO = XX ↑ ↓

SPO2ON OFF PR

GAS - ALARM LIMITS - ETCO2ETCO2 HI =

XXLO = XX ↑ ↓

RRON OFF ETCO2

GAS - ALARM LIMITS - RRRR HI =

XXLO = XX ↑ ↓

RRON OFF ETCO2


Tyco Nellcor N-2500

Contents
OverviewThe 90433A-05 Flexport system interface enables information from a Tyco Nellcor N-2500 gas analyzer to be displayed on Spacelabs Healthcare monitors.

Configure the gas analyzer as shown in Table 1. Consult the analyzer manual for additional configuration setup procedures.

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the gas analyzer, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the gas analyzer. To control other interface functions, refer to the sections that follow.

Table 1: Gas Analyzer Configuration

Baud Rate

Character Length

Parity Setting Stop Bit Transition Connector

9600 8-bit none 1 131-0686-xx (9-pin)




• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector in the gas analyzer.


Tyco Nellcor N-2500

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the gas analyzer.




� Current isoflurane value

� Current nitrous oxide value

� Current respiration rate


� Current end tidal CO2 (mmHg) value


� � � � �

2.9 ISO 40 N2O 22 RRGAS

24 ETCO2

% % BPM mmHg

0.1 ENF 0.4 HAL 4.2 PR 96 SPO2

% % BPM %

� � �

� �

GAS

ETCO2 = 24mmHg

SPO2 = 96%

RR = 22 BPM

N2O= 40%

� � � �

� � � � �

� ETCO2= 24mmHg N2O = 40%GAS

� RR = 22 BPM ISO = 2.9%

PR = 4.2 BPM HAL = 0.4%

� SPO2 = 96% ENF = 0.1%

� ICU 14


Tyco Nellcor N-2500

� Current pulse oximetry value

Current pulse rate

Current halothane value

� Current enflurane value

� Patient/room ID






Alarm limits for anesthetic agents can only be adjusted at the analyzer. When an agent parameter value exceeds an alarm limit, the Spacelabs Healthcare monitor does not send alarm data to the recorder, but the GAS parameter key flashes and a message is displayed on the monitor, indicating which parameter is in alarm.



analyzer.

• Alarm tones on the gas analyzer can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.


• Touch GAS.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.

To adjust alarms limits:

• Touch GAS.• Select ALARM LIMITS.• Select an alarm parameter.• Select HI= or LO=.• Use the arrow keys to adjust.


Tyco Nellcor N-2500

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the analyzer’s parameters (refer to Figure 60-4). If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays GAS ALM OFF to the right of the GAS key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.







N2O60

PR 90 ETCO2 45GAS

ETCO2 = 24 mmHg20 05 01 SPO2 = 96%

PR 120 SPO2 100 RR = 22 BPM

50 90 N2O = 40%


Tyco Nellcor N-2500






Tyco Nellcor N-2500







AGENT — ZERO CALIBRATIONThe analyzer is performing a calibration. Agent processing is suspended while this message is displayed.

No

APNEA VIOLATION The apnea alarm limit has been violated. The limit is 20 seconds. Yes

COMMUNICATION LINK LOST Communication between the gas analyzer and the monitor has been interrupted. Yes

CO2 — ZERO CALIBRATIONThe analyzer is performing a calibration. EtCO2 and RR processing are suspended while this message is displayed.

No

GAS SYSTEM DISABLE

Displayed when you touch the DISABLE button on the analyzer. Agent, EtCO2, and RR processing are suspended while this message is displayed.

No

GAS SYSTEM PURGING

Displayed when you touch the START PURGE button on the analyzer. Agent, EtCO2, and RR processing are suspended while this message is displayed.

No

XXX LO LIMIT VIOLATION The XXX alarm limit has been violated (where XXX = ENF, ISO, or HAL). Yes

XXX LO LIMIT VIOLATION The XXX alarm limit has been violated (where XXX = ENF, ISO, or HAL). Yes


Tyco Nellcor N6000




ON OFFRefer to

page 39-2These keys appear on

the bedside monitor only.

CO2 - SETUP

SIZE SWEEP SPEED

LARGE TXTSMALL TXT

CO2 - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF

CO2 - SETUP - SWEEP SPEED50

mm/sec25

mm/sec12.5

mm/sec6.25

mm/sec


Tyco Nellcor N6000

CO2



ON OFFRefer to

page 39-1

CO2 - ALARM LIMITS

SPO2 PULSE ETCO2 RESP I CO2

CO2 - ALARM LIMITS - I CO2I CO2 HI =

XXLO = XX

I CO2ON OFF SpO2

CO2 - ALARM LIMITS - RESPRESP HI =

XXLO = XX

RESPON OFF I CO2


XXLO = XX

ETCO2ON OFF RESP

CO2 - ALARM LIMITS - PULSEPULSE HI =

XXLO = XX

PULSEON OFF ETCO2

CO2 - ALARM LIMITS - SpO2SPO2 HI =

XXLO = XX

SPO2ON OFF PULSE


Tyco Nellcor N6000

Contents
OverviewThe 90442A Flexport system interface enables information from a Tyco Nellcor N6000 analyzer to be displayed on Spacelabs Healthcare monitors.

Configure the analyzer as shown Table 1. Consult the analyzer manual for additional configuration setup procedures.

To complete the configuration and set the serial output format to FLEXPORT, complete the following steps on the analyzer:

1 Press the FREEZE hard key on the analyzer.

2 Simultaneously touch soft keys 2 and 4 (they are unlabeled).

3 Touch the SET CUSTOM DEFAULTS soft key.

4 Touch the SYSTEM soft key.

5 Touch the SYSTEM VARIABLES soft key.

6 Touch the COMM MODE soft key until FLEXPORT is highlighted.

7 Press the MENU hard key on the analyzer twice to return to the Main Monitoring screen.


Baud Rate




9600 2.0 045-0031-xx 131-1039-xx(9 pin)


Tyco Nellcor N6000









• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 9-pin connector on the back of the analyzer.

� � � �

35 ETCO2 1 I CO2CO2

98 SpO2

mmHg mmHg %

16 RESP 70 PULSE

BPM bpm

� � �

� � ��

CO2

SpO2= 98%

PULSE= 70bpm

ETCO2= 35mmHg

RESP= 16BPM

� �


Tyco Nellcor N6000



� Current inspired CO2 value






Patient/room ID










� �

� SpO2 = 98% I CO2 = 1mmHgCO2

� PULSE = 70bpm

� ETCO2 = 35mmHg

� RESP = 16BPM

ICU 4


Tyco Nellcor N6000









SpO2100 ETCO2 66 I CO2 8 C

O2

98 SpO2

92 0 0 %

PULSE 80 RESP 30 70 PULSE

0 6 bpm


Tyco Nellcor N6000





Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 6.25, 12.5, 25, and 50 mm/second.









Tyco Nellcor N6000







printout.









Tyco Nellcor N6000







COMMUNICATION LINK LOSTThe communication between the Flexport system interface and the 60-RS-SL interface is interrupted.

Yes

CO2 SENSOR WARMING The CO2 and AGENT sensors are warming up in the CO2 analyzer. No

SAMPLING LINE OCCLUDED The sample line is occluded or the pump is defective. Yes

APNEA No CO2 waveform has been detected for more than the set APNEA period. Yes

PULSE SEARCH Pulse is too weak. No

AIRWAY OCCLUDED The airway adapter is occluded. No

CO2 SENSOR NOT CONNECTED The CO2 sensor is not plugged into the Tyco Nellcor N6000. No

SPO2 SENSOR NOT CONNECTED The SpO2 sensor is not plugged into the Tyco Nellcor N6000. No

CO2 DISABLED CO2 monitoring has been disabled on the Tyco Nellcor N6000. No

SPO2 DISABLED SpO2 monitoring has been disabled on the Tyco Nellcor N6000. No



Tyco Nellcor Symphony N3000

Directory of KeysSPO2

SpO2 - MAIN MENUALARM LIMITS SETUP


ON OFF


SpO2 - SETUP

SIZE SWEEP SPEED

LARGE TXTSMALL TXT

SpO2 - SETUP - SIZEWAVEFORM SIZE

↑SIZE

↓ON OFF

SpO2 - SETUP - SWEEP SPEED50

mm/sec25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec0.78

mm/sec

SpO2 - ALARM LIMITS

SPO2 PR

SpO2 - ALARM LIMITS - PRPR HI =

XXLO = XXON OFF


XXLO = XXON OFF


Contents
OverviewThe 90442A Flexport system interface enables information from a Tyco Nellcor Symphony N3000 pulse oximeter to be displayed on Spacelabs Healthcare monitors.

Configure the pulse oximeter as shown Table 1.

The Flexport system interface is fully compatible with N3000 oximeters (N3000-N20, N3000-N21, and N3000-22). Other N3000 oximeters (for example, international oximeters) may require modifications. Refer to Directions For Use supplied with the GPSI adapter or contact Tyco Nellcor technical service for instructions.


Baud Rate


Installation Kit

Part Number


Part Number

9600 N3000: UIF 3.4.0 045-0037-xx 131-0686-xx (9 pin)



Connecting the Flexport System InterfaceTo connect the Flexport system interface to the N3000 oximeter, complete the steps listed in the following Quickstart.

Refer to Directions For Use supplied with the GPSI adapter for instructions on connecting the N3000 oximeter to the GPSI adapter.


Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the patient monitor.





• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the RS-232 connector on the Nellcor GPSI

communications adapter.• Plug the round DIN connector of the GPSI cable into the patient monitor serial port.

� �

SpO2

98 SPO2

%

70 PR

bpm

� �









� Patient/room ID






When all parameter alarms are turned OFF, alarm status messages will still cause the SPO2 key to flash.


� � �

SpO2

SPO2= 98%

PR= 70bpm

�

� �

� SpO2 = 98% SpO2

� PR = 70bpm

� ICU 14



Note:• Turning Flexport system interface alarms ON or OFF does not affect alarms settings on the pulse

oximeter.

• Alarm limits can only be adjusted at the pulse oximeter. Alarm violation is detected at the oximeter and the Flexport system interface reports the alarm if it is turned ON for that parameter.

• Alarm tones on the oximeter can be selectively enabled or disabled. If alarm tones are also disabled at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.

Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the pulse oximeter’s parameters (refer to Figure 62-4). If alarms for both parameters are turned OFF, the Spacelabs Healthcare monitor displays SPO2 ALM OFF to the right of the SPO2 key. If alarms are turned ON for any parameter, a bell is displayed. The alarm bell flashes when an alarm limit is violated.



• Touch SPO2.• Select ALARM LIMITS.• Select an alarm parameter.• Touch the parameter alarm ON/OFF key.



SPO2 100 SPO2

98 SPO2

92 %

PR 80 70 PR

0 bpm




























printout.


Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the pulse oximeter or cabling. If the Spacelabs Healthcare monitor displays this message, perform the following troubleshooting steps:



The pulse oximeter serial port is not operational when the oximeter is operating on batteries.

GPSI Communications Adapter LED Status

The Nellcor GPSI adapter has two LED indicators labeled N3000 and HOST. They indicate the status of communications with the Flexport system interface as follows:

• If both LED indicators are ON, then the GPSI communications adapter, the pulse oximeter, and the Flexport system interface are all successfully communicating.

• If the HOST indicator is flashing and the pulse oximeter indicator is OFF, check the cabling to the Flexport system interface and the Spacelabs Healthcare monitor.

• If the N3000 indicator is flashing and the HOST indicator is ON, check the configuration on the pulse oximeter (for example, software version, RS-232 mode settings, or BAUD rate).

• If both LED indicators are flashing, the GPSI adapter has failed its self test and must be replaced. Contact Nellcor technical service for replacement.

To print the patient monitor display:




Tyco Puritan Bennett 840



MODE VIEW STATUS VIEW ALARMS PRINT

VENT - SETUP LARGE TXTSMALL TXT

VENT - ALARM LIMITS

RR Vte Vmin Ppeak APNEA O2 Src.

VENT - ALARM LIMITS - O2 Src.O2 Src. O2 Src.

ON OFF RR


XXAPNEA

ON OFF O2 Src.

VENT - ALARM LIMITS - PpeakPpeak HI =

XXXPpeak

ON OFF APNEA


XX.XVmin

ON OFF Ppeak

VENT - ALARM LIMITS - VteVte LO =

X.XXVte

ON OFF Vmin


XXRR

ON OFF Vte


Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Ventilator Mode History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Selecting a Display Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OverviewThe 90436A-15 Flexport system interface allows information from a Tyco Puritan Bennett 840 ventilator to be displayed on Spacelabs Healthcare monitors.



Baud Rate

Character Length


TransitionConnector

Part Number

9600 8-bit none 1 131-1039-xx










• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the DIGITAL OUTPUT connector on the ventilator.

� � � � � �

1.8I:E

21Ppeak

cmH2O 0Pplat

cmH2O 21O2

% VENT

1.22Vte

L

10.5 PEEP

cmH2O8 Pmean

cmH2O30.0 Vmin

L 27RR

BPM

� � �





� Ratio of inspiratory time to expiratory time



� Oxygen level


� Tidal volume


Respiratory rate

Minute volume



Patient/room ID

� �

VENT

Ppeak= 21cmH2OPEEP= 10.5cmH2O �Vte= 1.22L �RR= 27BPM

�

� � � � �

RR= 27BPM Vte= 1.22L VENT

� O2 = 21% Vmin= 30.0L

� Ppeak= 21cmH2O I:E = 1.8

� PEEP= 10.5cmH2O Pmean= 8cmH2O

ICU 14









Note:• The expired tidal volume (Vte) alarm displayed on the Spacelabs Healthcare monitor reflects the

spontaneous low Vte alarm on the ventilator.

• The Spacelabs Healthcare monitor does not display the mandatory high Vte, mandatory low Vte, and spontaneous high Vte alarms from the ventilator.

• Turning Flexport system interface alarms ON or OFF does not affect alarm settings on the ventilator.


• Alarm tones on the ventilator can be temporarily silenced. If alarm tones are also OFF at the Spacelabs Healthcare monitor(s), alarm violations will be reported visually only.












Ppeak120

Vte 0.00 APNEA20

VENT

1.22 Vte

LVmin 0.3 RR 70

27 RR

BPM



Viewing Ventilator Mode HistoryChronological history of the last eight ventilator mode settings are displayed in the waveform zone with the oldest value at the top of the left column and the most recent value at the bottom of the right column. Possible modes include A/C, SPONT, SIMV, and BILEVEL.








15:4715:47

A/CSIMV/PS

15:4915:49

SIMV/PSSPONT V

ENT

1.21 Vte

L15:47 A/C 15:51 A/C/PS15:49 A/C 15:56 SIMV/PS 27 RR

BPM





Status MessagesThe message CIRCUIT DISCONNECT indicates that the ventilator has detected a disconnected circuit (no ventilation). If the monitor displays this message, check the patient and reconnect the circuit.











CIRCUIT DISCONNECT Ventilator detects circuit disconnect; patient ventilation has stopped. Yes

NO AIR/O2 SUPPLY Ventilator is not delivering breaths to the patient. Yes

LOW PRS O2 INLET

Pressure at the oxygen inlet fitting is less than 35 psig. An O2 Source alarm is also triggered. The ventilator generates an alert when O2 equals 21% and generates an alarm when O2 is 22% or greater.

Yes



Tyco Puritan Bennett 7200A/AE


VENT - MENUALARM LIMITS SETUP

FREEZE VIEWSTATUS

VIEW ALARMS PRINT

ON OFFRefer to

page 64-2

VENT - SETUP

SIZE SWEEP SPEED

WAVE LARGE TXTPRS FLO SMALL TXT


mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec0.78

mm/sec0.39

mm/sec


↑SIZE

↓ON OFF



VENT


FREEZE VIEWSTATUS

VIEW ALARMS PRINT

ON OFFRefer to

page 64-1

VENT - ALARM LIMITS

RR VT Vmin PIP PEEP I : E APNEA SpO2*

VENT - ALARM LIMITS - SpO2SpO2 HI =

XXLO = XX

RRON OFF SpO2


XXAPNEA

ON OFF SpO2

VENT - ALARM LIMITS - I : EI : E LO =

X.XI : E

ON OFF APNEA


XXPEEP

ON OFF I : E


XXXLO = XXX

PIPON OFF PEEP


XX.XVmin

ON OFF PIP

VENT - ALARM LIMITS - VTVT LO =

X.XXVT

ON OFF Vmin


XXRR

ON OFF VT

*Only SpO2 alarm limit is displayed when activated.



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Viewing Ventilator Mode History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OverviewThe 90436A-01 and 90436A-41 Flexport system interfaces enable information from a Tyco Puritan Bennett 7200A/AE ventilator to be displayed on Spacelabs Healthcare monitors.



Baud Rate

Character Length

Parity Setting

Stop Bit

TransitionConnector

Part Number


9600 8-bit none 1 131-0685-xx 26300 Rev. E or higher









• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the DIGITAL OUTPUT connector on the ventilator.• If you are using the 90436A-41 Flexport system interface, plug the

9-pin connector into the ANALOG OUTPUT connector on the side of the ventilator.

SDLCcable

SDLCterminator

modularcable

Flexport

interface

ventilator

25-pin connectorto DIGITAL OUTPUT(back of ventilator)

9-pin connector

(with 90436A-41 Flexport system interface only)to ANALOG OUTPUT

SpacelabsHealthcare

monitor

system




Note:Pressure or flow waveforms are available only with the 90436A-41 Flexport system interface.




� � � � � � �

1.8I:E

21PIP

cmH2O 0PLT

cmH2O 21FiO2

% VENT

1.22VT

L

WAVE=PRES

97SpO2

% 1PEEP

cmH2O8 MAP

cmH2O30.0 Vmin

L 27RR

BPM

� � �

� � � �

VENT

VT=1.22L WAVE=PRES

RR= 27BPMPIP= 21cmH2OPEEP= 1cmH2O

� � � � �

RR= 27BPM VT= 1.22L VENT

� FiO2 = 21% PIP= 21cmH2O

PEEP= 1cmH2O SpO2= 97%

� Vmin= 30.0L MAP= 8cmH2O

� ICU 14



� Ratio of exhalation time to inspiratory time





� Tidal volume

� Current waveform mode (Flexport 90346A-41 only)


Respiratory rate

� Minute volume


Positive end expiratory pressure

� O2 saturation

� Patient/room ID





















PIP120

3 SpO20

90 VT 0.00 APNEA20 V

ENT

1.22 VT

L

I : E 1.0 PEEP 0 Vmin 0.3 RR 70 27 RR

BPM



Viewing Ventilator Mode HistoryChronological history of the last eight ventilator mode settings are displayed in the waveform zone with the oldest value at the top of the left column and the most recent value at the bottom of the right column. Possible modes include CMV, SIMV, CPAP, SIMV/PS, CPAP/PS, SIMV/FB, CPAP/FB, or UNKNOWN MODE.



Note:Pressure or flow waveforms are available only with the 90436A-41 Flexport system interface.

Turning Waveforms ON or OFFYou can turn the waveform display OFF and display only the numeric values. When the waveform is OFF, the SWEEP SPEED key, and the SIZE ↑ and SIZE ↓ keys are disabled.






15:4715:47

CMVSIMV/PS

15:4915:49

SIMV/PSCMV V

ENT

1.21 VT

L15:47 CMV 15:51 CPAP/PS 25 RR

15:49 CMV 15:56 SIMV/PS BPM





Selecting a Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the display. Available sweep speeds are: 25, 12.5, 6.25, 3.12, 1.56, 0.78, and 0.39 mm/second.








• Touch VENT.• Touch SETUP.• Touch WAVEFORM.• Select PRS or FLO.












• Touch LINK.• Select FREEZE ON.













LOW PRS O2 INLET Pressure at the oxygen inlet fitting is less than 35 psig, and the O2% is 22 or greater. No


LOW BATTERY Voltage of the internal batteries is too low to sustain one hour of operation. No

EXHAL VALVE LEAK Volume of exhalation gas is less than 10% of inspiration gas. No

LOW PULSE RATE Pulse rate is less than the set low pulse rate limit. No

HIGH PULSE RATE Pulse rate is greater than the set high pulse rate limit. No

DISCONNECT VENT Patient service system is disconnected or plugged. No

SPO2 PROBE OFF SpO2 probe is off the patient’s finger. No

POOR SPO2 SIGNAL SpO2 probe is dirty or probe is positioned incorrectly. No

SPO2 WRONG PLACE Placement of SpO2 probe is incorrect. No


Transonics HT-107

Directory of KeysFLOW

FLOW - MAIN MENU

SETUPFREEZE

PRINTON OFF

FLOW - SETUP

SIZE SWEEP SPEED

LARGE TXT This key is displayed on the bedside monitor only.SMALL TXT


mm/sec25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec0.79

mm/sec0.39

mm/sec

FLOW - SETUP - SIZEWAVE SIZE

↑SIZE

↓ON OFF


Transonics HT-107

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Display Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Freezing the Waveform on the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Printing the Current Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
OverviewThe 90442A Flexport system interface enables information from a Transonics Systems HT-107 Medical Flowmeter to be displayed on Spacelabs Healthcare monitors.

Configure the flowmeter as shown in Table 1. Consult the flowmeter manual for additional configuration setup procedures

Connecting the Flexport System InterfaceTo connect the Flexport system interface to the flowmeter, complete the steps listed in the following Quickstart.

The Spacelabs Healthcare monitor is now ready to display information from the flowmeter. To control other interface functions, refer to the sections that follow.

Table 1: Flowmeter Configuration

Baud Rate




9600 1.25 045-0030-xx 131-0684-xx (25-pin)




• Plug the other end of the modular cable into the transition connector.• Plug the transition connector into the 25-pin connector on the back of the flowmeter.


Transonics HT-107

Display DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the flowmeter.




� FLOW parameter key

� Current flow value

� Patient/room ID

� �

FLOW

1.20 BL FLOl/m

� �

FLOW

BLFLO = 1.20 l/m

� �

BL FLO = 1.20 l/m FLOW

� ICU 14


Transonics HT-107







• Touch FLOW.• Touch SETUP.• Touch SIZE.• Select WAVEFORM ON/OFF.


• Touch FLOW.• Touch SETUP.• Touch SIZE.• Touch SIZE ↑ or SIZE ↓ to adjust the waveform size.


Transonics HT-107





Freezing the Waveform on the DisplayThe FREEZE ON key enables you to freeze the waveform display. When you freeze the waveform, the Flexport system interface continues to process, update, and display numeric information.



• Touch FLOW.• Touch SETUP.• Touch SWEEP SPEED.• Select the desired speed.


• Touch FLOW.• Touch SETUP.• Select LARGE TXT or SMALL TXT.


• Touch FLOW.• Select FREEZE ON.


Transonics HT-107



printout.


Status MessagesThe message COMMUNICATION LINK LOST indicates a problem with the flowmeter or cabling. If the monitor displays this message, perform the following troubleshooting steps:

• Verify that the flowmeter is powered ON.


Table 2 lists the status messages that the Flexport system interface reports for the flowmeter during Flexport system interface operation.


• Touch FLOW.• Touch PRINT.




Communication between the flowmeter and the monitor has been interrupted. Yes

ACOUSTIC ERROR Indicates a break in either the ultrasonic or electrical signal path. No


VIASYS Ventilator, Vela



FREEZEWAVEFORMS VIEW

ALARMS PRINTON OFF

VENT - SETUP

SIZE SWEEP SPEED

LARGE TXTSMALL TXT


mm/sec25

mm/sec12.5

mm/sec6.25

mm/sec3.12

mm/sec1.56

mm/sec0.78

mm/sec0.39

mm/sec


↑SIZE

↓ON OFF

VENT - ALARM LIMITS

Apnea Ppeak Ve

VENT - ALARM LIMITS - VeVe LO =

XXXXON OFF

VENT - ALARM LIMITS - PpeakPpeak HI =

XXXXLO = XXXXON OFF

VENT - ALARM LIMITS - ApneaApnea HI =

XXXXON OFF

These keysappear on thebedsidemonitor only.



Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Connecting the Flexport System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Screen Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Enabling Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Viewing Alarm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Alarm Recordings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Entering Setup Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Printing the Current Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OverviewThe 90436A-18 Flexport system interface enables information from a VIASYS Vela Ventilator to be displayed on Spacelabs Healthcare monitors.



Spacelabs Healthcare Model Number/Ventilator Name and Model Number

Baud Rate Cabling Adapter Minimum

Software Version

Spacelabs Healthcare 90436A-18 9600 9-pin modular adapter

required (P/N 131-0686-03) (or 25-pin modular adapter with 25-pin/9-pin converter)

V1.00.01EN

Bird Monitor Interface15674 9600 V3.3







• Plug the other end of the modular cable into the 9-pin modular adapter, then into the jack labeled TO MONITOR on the BMI.

• Plug one end of a fiber optic cable into the fiber optic jack labeled DATA IN on the BMI.• Plug the other end of the fiber optic cable into the fiber optic jack labeled DATA LINK

on the ventilator.• Ensure that all screw locks are tight.• Connect the wire from the power adapter to the jack labeled INPUT 9/15 VDC on the

BMI.• Turn ON the ventilator, then plug in the BMI interface power adapter.• Connect the long branch of the SDLC cable to the SDLC connector on the back of the

monitor.• Attach the SDLC terminator to the SDLC cable (refer to Figure 66-1).• Connect the SDLC cable to the 9-pin male connector on the Flexport system interface.

SDLCcable

SDLCterminator

Flexport

interface

Bird

SpacelabsHealthcare

monitor

system

monitor interface


power adapter

modularcable

9-pinadapter

data indata link

optional data out connection

powerconnector



Caution:Attach only Spacelabs Healthcare-approved accessories to RS-232 connectors.

Note:• The maximum total SDLC cable length between any Flexport system interface and its power source

should not exceed 6 feet (1.8 m). The power source is the monitor or the module housing.

• If you use SDLC links to connect other devices (such as expansion housings or printers) to the monitor, the Flexport system interface must be the device closest to the monitor.


Screen DetailWhen you power ON a Spacelabs Healthcare monitor that is properly connected to a Flexport system interface, the monitor provides the following information from the ventilator.

Figure 66-2: Bedside monitor, large text


� Peak inspiratory pressure — displays high pressure alarm


� Respiratory rate


� Inspiratory tidal volume

� � � � � �

999 Ppeak 99.9 Pmean 999 Rate VENT

9999 Vti

cmH2O cmH2O bpm ml

99 PEEP 99.9 Ti 99.9 Ve 9999 Vte

cmH2O Sec L ml

� �

� �

VENT

Ppeak=999cmH2O

PEEP=99cmH2O �

Vte=9999ml

Ve=99.9L

� �



� Alarm status bell (any)

� Exhaled tidal volume

Exhaled minute volume

Inspiratory time









• Alarm limits on the Flexport system interface can only be adjusted at the ventilator and are only shown on the Spacelabs Healthcare monitor for reference.

Apnea AlarmThe Apnea alarm is a high limit alarm, which displays if a breath isn’t detected within a preset period of time. The alarm limit is adjustable, and may be set at the Vela ventilator. Figure 66-4 displays a recording of an Apnea HI Limit alarm at 20 seconds. Notice that the unit of measure (seconds) is not included in the recorder strip.

Figure 66-4: Apnea HI Limit alarm

Caution:• The Apnea HI Limit alarm doesn’t display an associated parameter on the bedside monitor.

• The breaths per minute rate may appear abnormally high when an Apnea HI Limit alarm occurs.

Refer to the Vela Ventilator System, Operator’s Manual for further information.



Viewing Alarm SettingsThe VIEW ALARMS key enables you to display the current alarm settings for the ventilator’s parameters. If alarms for all parameters are turned OFF, the Spacelabs Healthcare monitor displays VENT ALM OFF to the right of the VENT key. If alarms are turned ON for any parameter, a bell is displayed. (An alarm bell also is displayed, on the large text view, next to the parameters for which alarms are turned ON.) The alarm bell flashes when an alarm limit is violated.

The alarm limits on the VIEW ALARMS display correspond to the limits which are set for each of the parameters on the ventilator.

• If the ventilator displays the low Ppeak limit as OFF, the low Ppeak limit in VIEW ALARMS displays as zero (0).

• If the ventilator displays the low VE limit as OFF, the low VE limit in VIEW ALARMS displays as 0.1.

Alarm RecordingsAlarm recordings that are sent to a printer will display only one parameter at a time. If multiple parameters are simultaneously in alarm, the precedence on the display is:

• Apnea

• Ppeak

• VE










Adjusting the Waveform SizeIf the waveform is too large to fit within the display zone, use the waveform size keys to adjust the screen size.

Note:The WAVEFORM ON/OFF key must be set to ON for the size keys to function.

To turn the waveform screen ON or OFF:






Selecting a Screen Sweep SpeedThe sweep speed determines the speed at which the waveform trace moves across the screen. Available sweep speeds are: 0.39, 0.78, 1.56, 3.12, 6.25, 12.5, 25, and 50 mm/second.


Note:Sweep speeds below 1.56 mm/sec are supported on the display, but are not supported on the recordings.

Selecting a Screen FormatTwo screen formats are available for the bedside monitor (refer to Screen Detail on page 66-5).


Freezing the Waveform DisplayThe FREEZE ON/OFF key enables you to freeze the waveform display. When you freeze the waveform, the interface continues to process and update the numeric information.




To select a screen format:


To freeze the waveform display:

• Touch VENT.• Touch FREEZE ON/OFF.



Selecting a WaveformThe WAVEFORMS key enables you to select a pressure, a flow, or a volume waveform. Touch the WAVEFORMS key until the desired type of waveform displays. The default setting displays the pressure waveform.

Note:This key is only available at the bedside monitor.

Volume Waveform

The volume waveform displays on a Spacelabs Healthcare monitor at 10% of the value displayed on the VIASYS Ventilator. If the value on the VIASYS Ventilator is 800, it will display at 80 on the monitor.

All recordings generated using the RECORD key or as a result of an alarm condition are scaled in this manner.

Printing the Current ScreenTouch the PRINT key to print the information shown on the current screen. Each recording is identified by the bed name, patient name, time, and date.


printout.


To select a waveform:

• Touch VENT.• Touch WAVEFORMS.





Status MessagesTable 2 lists the status messages that the Flexport interface reports for the ventilator during operation.

Status Alarms

Status Alarms are status messages, which have “alarm-like” characteristics such as:

• A flashing open door key.

• An audible tone.

The COMMUNICATION LINK LOST message is an example of a Status Alarm.


• Verify that the ventilator is turned ON.


Note:The COMMUNICATION LINK LOST message displays for approximately 40 seconds prior to the channel disappearing from the screen.



PRESSURE WAVEFORM SELECTED The current waveform is a pressure waveform. No

FLOW WAVEFORM SELECTED The current waveform is a flow waveform. No

VOLUME WAVEFORM SELECTED The current waveform is a volume waveform. No


Appendix A — Symbols

The following list of international and safety symbols describes all symbols used on Spacelabs Healthcare products. No one product contains every symbol.

HELP Key Keyboard Connection

SPECIAL FUNCTIONS Key Mouse Connection

RECORD Key START/STOP Key

NORMAL SCREEN Key START/STOP

MONITOR SETUP Key STOP or CANCEL Key

ALARMS Key CONTINUE Key

PREVIOUS MENU Key ENTER Key

ON — Power Connection to Mains OFF — Power Disconnection from Mains

ON Position for Push Button Power Switch

OFF Position for Push Button Power Switch

On Direction ON/OFF

ON — Part of the Instrument Only OFF — Part of the Instrument Only

Standby STANDBY KeyPower ON/OFF Key

Book Title Variable A-1


PAUSE or INTERRUPT Slow Run

Alarm Reset Power Indicator LED

Alarm Audio ON Alarm Audio OFF

Alarm Audio Paused Activate Telemetry Recorder

Indicator — Remote Control Indicator — Local Control

PRINT REPORT Key Indicator — Out of Paper

Partial ON/OFF Recorder Paper

Normal Screen Return to Prior Menu

Clock/Time Setting Key TREND/TIMER Key

HELP (Explain Prior Screen) Key Keypad

Activate Recorder for Graphics Indoor Use Only

START (NIBP) Key Auto Mode (NIBP)

Television; Video Display Video Output

Output (Non-terminated) No Output (Terminated)

123 1

23

?



Data Input/Output Input/Output

Input Reset

Menu Keys Waveform/Parameter Keys

Monitor SetupSelect Program Options Set Initial Conditions Menu

Access Special Function Menu Return Unit to Monitor Mode

Serial Port 1 Serial Port 2

External Marker Push Button Connection SDLC Port

Arterial Pulse Electrocardiograph or Defibrillator Synchronization

Gas Exhaust Foot Switch

Enlarge, Zoom Delete

PCMCIA Card Event

Keep Dry Fragile; Handle with Care

Environmental Shipping/Storage Altitude Limitations This Way Up

Environmental Shipping/Storage Temperature Limitations

Environmental Shipping/Storage Humidity Limitations

123

123

A

123

B123

1 2

SDLC

x

12,200 m



Open Padlock Closed Padlock

Down Arrow Up Arrow

Hard Drive Power Indicator LED

Antenna Mermaid Connector

Microphone Omnidirectional Microphone

Audio Output, Speaker Universal Serial Bus

Network Connection Oxygen reference gas port

Gas Sampling Port Gas Return Port

Low Priority Alarm Nurse Call

High Priority Alarm Medium Priority Alarm

Alarms Paused Nurse Alert Interface

Battery Status Alarm OFF

BatteryReplace only with the appropriate battery.

Low Battery

Ref.



All batteries should be disposed of properly to protect the environment. Lithium batteries should be fully discharged before disposal. Batteries such as lead-acid (Pb) and nickel-cadmium (Ni-Cd) must be recycled. Please follow your internal procedures and or local (provincial) laws regarding disposal or recycling.

Replace only with the appropriate battery.(+ / - signs may be reversed)

Caution - hazardous voltages. To reduce risk of electric shock, do not remove the cover or back. Refer servicing to a qualified field service engineer (U.S.A.).DANGER - High Voltage (International)

This symbol indicates that the waste of electrical and electronic equipment must not be disposed as unsorted municipal waste and must be collected separately. Please contact an authorized representative of the manufacturer for information concerning the decommissioning of your equipment.

Protective Earth Ground Functional Earth Ground

Replace Fuse Only as Marked Fuse

Power supply jack polarity. (+ / - signs may be reversed) Equipotentiality Terminal

Alternating Current Direct Current

Both Direct and Alternating Current AC/DC Input

Amperes Hertz

Volts Watts

IEC 60601-1 Type B equipment. The unit displaying this symbol contains an adequate degree of protection against electric shock.

IEC 60601-1 Class II equipment, double-isolated. The unit displaying this symbol does not require a grounded outlet.

A Hz

V W



IEC 60601-1 Type BF equipment which is defibrillator-proof. The unit displaying this symbol is an F-type isolated (floating) patient-applied part which contains an adequate degree of protection against electric shock, and is defibrillator-proof.

IEC 60601-1 Type BF equipment. The unit displaying this symbol is an F-type isolated (floating) patient-applied part providing an adequate degree of protection against electric shock.

IEC 60601-1 Type CF equipment. The unit displaying this symbol is an F-type isolated (floating) patient-applied part providing a high degree of protection against electric shock, and is defibrillator-proof.

IEC 60601-1 Type CF equipment. The unit displaying this symbol is an F-type isolated (floating) patient-applied part providing a high degree of protection against electric shock.

Loop Filter Adult Noninvasive Blood Pressure (NIBP)

ETL Laboratory Approved Canadian Standards Association Approved

Risk of Explosion if Used in the Presence of Flammable Anesthetics

Operates on Non-Harmonized Radio Frequencies in Europe

Note Note Caution - Consult Accompanying Documents

Warning Warning About Potential Danger to Human Beings Caution Caution About Potential Danger to a

Device

Noninvasive Blood Pressure (NIBP), Neonate Fetal Monitor Connection (Analog)

Fetal Monitor ConnectionRS-232 (Digital)

Physiological Monitor Connection RS-232 (Digital)

Symbol Set, Adult/Pediatric Cuff Sizes

Symbol Set, Neonatal Cuff Sizes

® U S

!!



NIBP Cuff, Neonatal 1 NIBP Cuff, Neonatal 2

NIBP Cuff, Neonatal 3 NIBP Cuff, Neonatal 4

NIBP Cuff, Neonatal 5 NIBP Cuff, Single Hose

NIBP Cuff, Dual Hose Consult Instructions For Use

NIBP Cuff, Surface Applied to Patient

NIBP Cuff, Child Size, Long (12 to 19 cm)

NIBP Cuff, Small Adult Size, Long (17 to 25 cm)

NIBP Cuff, Small Adult Size (17 to 25 cm)

NIBP Cuff, Adult Size, Long (23 to 33 cm)

NIBP Cuff, Large Adult Size, Long (31 to 40 cm)

NIBP Cuff, Large Adult Size (31 to 40 cm)

NIBP Cuff, Adult Size (23 to 33 cm)

NIBP Cuff, Child Size (12 to 19 cm)

NIBP Cuff, Infant Size (8 to 13 cm)

NIBP Cuff, Neonatal 1 Size (3 to 6 cm)

THIS SIDE TO PATIENT

CHILD, LONG

SMALL ADULT, LONG

SMALL ADULT

ADULT, LONG

LARGE ADULT, LONG

LARGE ADULT

ADULT CHILD

INFANT NEONATAL 1





NIBP Cuff, Neonatal 4 Size(7 to 13 cm)

NIBP Cuff, Neonatal 5 Size(8 to 15 cm)

NIBP Cuff, Thigh Size (38-50 cm) NIBP Cuff, Soft Material

NIBP Cuff, Nylon Material NIBP Cuff, Vinyl Material

Place Artery Symbol and Arrow over Brachial or Femoral Artery Quantity

Happy Face Sad Face

Magnifying Glass Compression

File Cabinet List of Rooms

Arrows Printer

Recycle Service Message

Non Sterile PVC-Free (Polyvinyl Chloride)

Latex-Free Do Not Reuse; Single Use Only

Radio transmitting device; elevated levels of non-ionizing radiation Reusable

Batch Code Reference Number or Order Number

NEONATAL 2 NEONATAL 3

NEONATAL 4 NEONATAL 5

THIGH SOFT

NYLON VINYL

ARTERY QTY

PVC

LATEX 2

LOT REF



Abbreviations used as symbols are shown below.

Date of Manufacture Nellcor Oxisensor II Compatible

UL recognized component in Canada and United States Novametrix Compatible

Nellcor OxiMax Compatible Spacelabs TruLink Compatible

Masimo SET Compatible Nellcor OxiMax Compatible

Spacelabs Compatible

1 - 32 Access Codes 1 Through 32 AIR Air

ANT 1ANT 2

Diversity Antenna System 1Diversity Antenna System 2

Arr1ArrNet2

Arrhythmia Net 1Arrhythmia Net 2

avDO2 Arterial/Venous Oxygen Difference CaO2 Arterial Oxygen

CHch

EEG, EMG, or ECG ChannelEEG Channels - CH1, CH2, CH3, CH4EMG Channel - CH5

cmH2O Centimeters of Water

C.O.COco

Cardiac Output CvO2 Venous Oxygen

DIAdia Diastolic ECG

ecg Electrocardiogram

EEGeeg Electroencephalogram EMG

emg Electromyogram

ESIS Electrosurgical Interference Suppression EXT External

NE2

NVX

R



FECG Fetal Electrocardiogram FHR1FHR2

Fetal Heart Rate, Channel 1Fetal Heart Rate, Channel 2

GNDgnd Ground Hgb Hemoglobin

HLOhlo High-Level Output Multiview Multi-Lead Electrocardiogram

NIBPnibp Noninvasive Blood Pressure N2O Nitrous Oxide

O2 Oxygen O2AV Oxygen Availability

PaO2 Partial Pressure of Arterial OxygenPRESSpressPRS

Pressure

PvO2Partial Pressure of Mixed Venous Oxygen

RESPresp Respiration

SDLC Synchronous Data Link Control

SPO2SpO2SpO2SaO2

Arterial Oxygen Saturation as Measured by Pulse Oximetry

SVO2SvO2SvO2

Mixed Venous Oxygen Saturation SYSsys Systolic

T1T2T3T4

Temperature 1Temperature 2Temperature 3Temperature 4

TEMPtemp Temperature

UA Uterine Activity or Umbilical Artery VO2 Oxygen Consumption

VAC Vacuum Connection UV Umbilical Venous
