9619_LG_42LE5500_42LE5500-UA_Chassis_LA02E_Televisor_LED-LCD_Manual_de_entrenamiento+diagramas.pdf

42LE550042LE55001080P 42LE550042LE5500LED Backlights

1080PDirect View LCD

Training

LCD-DV Troubleshooting42" Class Full HD 1080PLCD TV (42" diagonally)

Published October 8th, 2010Updated March 09th, 2011

OUTLINEOUTLINE

Preliminary Section:yContact Information, Preliminary Matters, Specifications,LCD Overview, General Troubleshooting Steps, Signal Distribution, Disassembly Instructions and Voltages

Troubleshooting Section: Board Operation Troubleshooting of :

Signal Distribution, Disassembly Instructions and Voltages

Disassembly Section: Removal of Circuit Boards

Switch Mode Power Supply with LED Backlight Driver Board

Main Board

Soft Touch Keys

Ft Control Board

y

Speakers

October 2010 LCD TV 42LE55002

42LE5500 LCD Direct View Display

Overview of Topics to be DiscussedOverview of Topics to be Discussed

42LE5500 LCD Direct View Display

Section 1This Section will cover Contact Information and remind the Technician of Important Safety Precautions for the Customers Safety as well as the Technician and the Equipment.

Basic Troubleshooting Techniques which can save time and money sometimes can be overlooked. These techniques will also be presented.

Thi S ti ill t th T h i i f ili ith th Di bl Id tifi ti dThis Section will get the Technician familiar with the Disassembly, Identification and Layout of the LCD Display Panel.

f S f CAt the end of this Section the Technician should be able to Identify the Circuit Boards and have the ability and knowledge necessary to safely remove and replace any Circuit Board or Assembly.


IMPORTANT SAFETY NOTICEIMPORTANT SAFETY NOTICE

Preliminary Matters (The Fine Print)Preliminary Matters (The Fine Print)

IMPORTANT SAFETY NOTICEIMPORTANT SAFETY NOTICE

The information in this training manual is intended for use by persons possessing an adequate background in electrical equipment, electronic devices, and mechanical systems. In any attempt to repair a major Product, personal injury and property damage can result. The manufacturer or seller maintains no liability for the interpretation of this information, nor can it assume any liability in conjunction with its use. When servicing this product, under no circumstances should the original design be modified or altered without permission from LG Electronics. Unauthorized modifications will not only void the warranty, but may lead to property damage or user injury If wires screws clips straps nuts or washers used to complete a ground path are removed foruser injury. If wires, screws, clips, straps, nuts, or washers used to complete a ground path are removed for service, they must be returned to their original positions and properly fastened.

CAUTIONCAUTIONCAUTIONCAUTION

To avoid personal injury, disconnect the power before servicing this product. If electrical power is required for diagnosis or test purposes, disconnect the power immediately after performing the necessary checks. Also be g p p , p y p g yaware that many household products present a weight hazard. At least two people should be involved in the installation or servicing of such devices. Failure to consider the weight of an product could result in physical injury.


ESD NoticeESD Notice (Electrostatic Static Discharge)(Electrostatic Static Discharge)

Todays sophisticated electronics are electrostatic discharge (ESD) sensitive. ESD can weaken or damage the electronics in a manner that renders them inoperative or reduces the time until their next failure. Connect an ESD wrist strap to a ground connection point or unpainted metal in the product. Alternatively, you can touch your finger repeatedly to a ground connection point or unpainted metal in the product. Before removing a replacement part from its package, touch the anti-static bag to a ground connection point orremoving a replacement part from its package, touch the anti static bag to a ground connection point or unpainted metal in the product. Handle the electronic control assembly by its edges only. When repackaging a failed electronic control assembly in an anti-static bag, observe these same precautions.

l fl fRegulatory InformationRegulatory Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful g p p ginterference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user isradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and the receiver; Connect the equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the dealer or an experienced radio/TV technician for help.


Customer Service (and Part Sales) (800) 243-0000

LG Contact Information

Technical Support (and Part Sales) (800) 847-7597USA Website (GSFS) http://gsfs-america.lge.comCustomer Service Website http://www.us.lgservice.comKnowledgebase Website http://lgtechassist.comLG Web Training https://lge.webex.com

New: 2010/11 Wireless Ready Models Software Downloads

Presentations with Audio/Video and Screen Notations

LG CS Learning Academy http://ln.lge.com/ilearn http://136.166.4.200

Training Manuals, Schematics with Navigational Bookmarks, Start-Up Sequence, Owners Guides, I t t Di Di i C t ID P d t Pi t d F t

Also available on the Plasma Page:PDP Panel Alignment Handbook,

Plasma Control Board ROM Update (Jig required)

Interconnect Diagrams, Dimensions, Connector IDs, Product Pictures and Features.

Published October 2010 by LG Technical Support and TrainingLG Electronics Alabama, Inc.

Plasma Control Board ROM Update (Jig required)


201 James Record Road, Huntsville, AL, 35813.

Safety and Handling Regulations

LCD Direct View OverviewLCD Direct View Overview

1. Approximately 20 minute pre-run time is required before making any picture performance adjustments from the Menu.

2. Refer to the Voltage/Current silk screening on the Switch Mode Power Supply.3. C-MOS circuits are sensitive to static electricity.3. C MOS circuits are sensitive to static electricity.

Use caution when dealing with these IC and circuits.4. Exercise care when making voltage and waveform checks to prevent costly short circuits

from damaging the unit. 5. Be cautious of lost screws and other metal objects to prevent a possible short in the 5 e cau ous o os sc e s a d o e e a objec s o p e e a poss b e s o e

circuitry.

Checking Points to be Considered

1. Check the appearance of the Replacement Panel and Circuit Boards for both physical damage and part number accuracy.

2 Check the model label Verify model names and board model matches2. Check the model label. Verify model names and board model matches.3. Check details of defective condition and history. Example: Oscillator failure dead set, etc


Basic Troubleshooting StepsBasic Troubleshooting Steps

Define, Localize, Isolate and Correct

Define Look at the symptom carefully and determine what circuits could be causing the failure. Use your senses Sight, Smell, Touch and Hearing. Look for burned parts and check for possible overheated components. Capacitors will sometimes leak dielectric material and give off a distinct odor Frequency of power supplies will change with the load or listen forand give off a distinct odor. Frequency of power supplies will change with the load, or listen for relay closing etc. Observation of the front Power LED may give some clues.

Localize After carefully checking the symptom and determining the circuits to be checked and after giving a thorough examination using your senses the first check shouldchecked and after giving a thorough examination using your senses the first check should always be the DC Supply Voltages to those circuits under test. Always confirm the supplies are not only the proper level but be sure they are noise free. If the supplies are missing check the resistance for possible short circuits.

Isolate To further isolate the failure, check for the proper waveforms with the Oscilloscope to make a final determination of the failure. Look for correct Amplitude Phasing and Timing of the signals also check for the proper Duty Cycle of the signals. Sometimes glitches or road bumps will be an indication of an imminent failureglitches or road bumps will be an indication of an imminent failure.

Correct The final step is to correct the problem. Be careful of ESD and make sure to check the DC Supplies for proper levels. Make all necessary adjustments and lastly always perform a Safety AC Leakage Test before returning the product back to the Customer


perform a Safety AC Leakage Test before returning the product back to the Customer.

42LE5500 PRODUCT INFORMATION SECTION42LE5500 PRODUCT INFORMATION SECTION

This section of the manual will discuss the specifications of the42LE5500


LCD Direct View Display

Wireless Media Box (Sold Separately)

Wireless Media BoxWireless Media Box

The Wireless Media box communicates to the television via a wireless receiver called a Dongle. The Dongle attaches to the Television via two connections:

1. HDMI Cable from the Dongle to the TV to transfer Audio and Video Signals.2. Wired Remote cable between the TV and Dongle for Control Functions.

Media Box

2. Wired Remote cable between the TV and Dongle for Control Functions.

Wired Remote to control the Media Box

Wi l R i /T itt

TV A/V Inputs

Wireless Receiver/TransmitterDongle

Attaches via Velcro tothe back of the set

HDMI


HDMI

Wireless Wireless Network Adaptor (ANNetwork Adaptor (AN--WF100)WF100)

Wireless Network Adaptor Sold Separately

Using the LG Wireless LAN for Broadband Adaptor, which is sold separately, allows the TV to connect to a wireless LAN network. The Wireless Network adaptor attaches to the

Television via either of the two USB connections:

Allows access to DLNA: Digital Living Network Alliance

AP (Wireless Router)

Wireless AdaptorSide A/V

Cat 5 Cable withRJ 45 Connectors

DongleSide A/VInputs

on each side


Modem

Basic SpecificationsBasic Specifications

Key TV Featuresy LED Plus w/Local Dimming NetCast Entertainment Access*

(Wi Fi Read )

Intelligent Sensor AV Mode II

(Cinema Sports Game)(Wi-Fi Ready) Wireless 1080p Ready* DLNA Certified TruMotion 120Hz

(Cinema, Sports, Game) Clear Voice II ISFccc Ready 24P Real Cinema TruMotion 120Hz

Full HD 1080p Resolution 5M:1 Dynamic Contrast Ratio Picture Wizard II

24P Real Cinema USB 2.0 (JPEG, MP3, DivX HD) DivX HD 4 HDMI V 1 3 w/Deep Color Picture Wizard II

(Easy Picture Calibration) Smart Energy Saving ENERGY STAR Qualified

4 HDMI V.1.3 w/Deep Color SIMPLINK Connectivity Dolby Digital 5.1 Decoder Infinite Sound ENERGY STAR Qualified Infinite Sound


Logo Familiarization Page 1 of 4Logo Familiarization Page 1 of 4

LED PlusPrepare to be dazzled. Tired of dark scenes or dull colors? LGs LED Plus technology provideseven greater control of brightness through localdimming to deliver amazing clarity and colordetail, as well as a more energy efficient TVcompared to conventional TVs.

TruMotion 120HzSee sports, video games and high-speed action with virtually no motion blur and in crystal clarity with LGs TruMotion 120Hz technology. Now your TV can keep up with the fastest moving scenes.

NetCastEntertainment on tap. NetCast Entertainment Access brings the best Internet services direct to your TVno computer required. Instantly access movies and TV shows, news and weather and the worlds largest library of


HD movies in 1080p.


FULL HD RESOLUTION 1080P HD R l ti Pi l 1920 (H) 1080 (V)FULL HD RESOLUTION 1080P HD Resolution Pixels: 1920 (H) 1080 (V)Enjoy twice the picture quality of standard HDTV with almost double the pixel resolution. See sharper details like never before. Just imagine a Blu-ray disc or video game seen on your new LG Full HD 1080p TV.

HDMI (1.3 Deep Color) Digital multi-connectivity HDMI (1.3 Deep color) provides a wider bandwidth (340MHz, 10.2Gbps) than that of HDMI 1.2, delivering a broader range of colors, and also drastically improves the data-transmission

Invisible SpeakerPersonally tuned by Mr. Mark Levinson for LG TAKE IT TO THE EDGE newly introduces Invisible Speaker

speed.

TAKE IT TO THE EDGE newly introduces Invisible Speaker system, guaranteeing first class audio quality personally tuned by Mr. Mark Levinson, world renowned as an audio authority. It provides Full Sweet Spot and realistic sound equal to that of theaters with its Invisible Speaker.

AV Mode "One click" Cinema, THX Cinema, Sport, Game mode.TAKE IT TO THE EDGE is a true multimedia TV with an AV Mode which allows you to choose from 4 different modes of Cinema, Sports and Game by a single click of a remote control


and Game by a single click of a remote control.


Clear Voice Clearer dialogue sound gAutomatically enhances and amplifies the sound of the human voice frequency range to provide high-quality dialogue when background noise swells.

Save Energy, Save MoneyIt reduces the plasma displays power consumption.The default factory setting complies with the Energy Star requirements and is adjusted to the comfortable level to be viewed at home.(Turns on Intelligent Sensor).

Save Energy, Save MoneyHome electronic products use energy when they're off to power features like clock displays and remote controls. Those that have earned the ENERGY STAR use as much as 60% less energy to perform these functions, while providing the same performance at the same price as less-efficient models. Less energy means you pay less on your energy bill. Draws less than 1 Watt in stand by.



Wireless ReadyWireless ReadyWireless 1080p Connectivity lets you cut loose from messy wires and still get a stunning Full HD picture. Disclaimer: Wireless media kit required and sold separately.

Picture WizardGet easy self-calibration with on-screen reference points for key picture quality elements such as black level, color, tint, sharpness and backlight levels. Take the guesswork out of picture adjustments with g g p jthis simple-to-use feature. It's not actually magic, but it will sure seem that way.

5M:1 Dynamic Contrast Ratio5M:1 Dynamic Contrast RatioWorrying about dark scenes is a thing of the past. The mega contrast ratio of 5,000,000:1 delivers vivid colors and deep blacks.

I t lli t SIntelligent SensorThe Intelligent sensor will monitor the room lighting environment. When the room lights go out, the TV will automatically adjust the picture for the best viewing enjoyment.


42LE5500 Remote Control42LE5500 Remote Control

TOP PORTION

BOTTOM PORTIONp/n AKB72914003


TV Rear Input / Output JacksTV Rear Input / Output Jacks

Rear In/Out Jacks

Side In/OutUSB1 or USB2 for SoftwareUpgrades, Music, Videos and Photos. Also

for the Wireless Network adaptor.Rear In/Out Jacks pUSB 2

LAN

USB 1

LAN

Component or Composite

Video/Audio 3

Wireless Media BoxRemote Jack Head

PhonesMAIN BOARDRear and Side

Input/Output locationsHDMI 4

Phones


HDMI 4

Software Updates (New and Changed Functions)Software Updates (New and Changed Functions)A wireless Internet Connection will work for Automatic Software Downloads, however if there are problems completing download, a Wired Internet Connection is preferred.

For network setup assistance, press the green button for the Simple Manual.

Bring up the Customers Menu then Press the Red button on Remote. Scroll down to item 9 Network Connections

With Software Update Highlighted, Press Select on Remote.


Continue on next page

Software Updates (New and Changed Functions) ContinuedSoftware Updates (New and Changed Functions) Continued

Automatic Internet Software UpdateOff A tomatic Soft are pdate does not ork- Off : Automatic Software update does not work

- On : if new Software released, Software download notice appears at turn on with two choices, Yes and Remind Me Later.

Check Update versionCheck Update version- comparison current software version and

Released software version

Additional TV Checks can be made by

After completion of the test, a Pop up menu is displayed with preloaded back ground picture.Select NO if everything is OK.

yScrolling down.Picture, Sound and Network Test

y g

If you select Yes;Service call number, Model name,SW version and serial No. is displayed. Note: Confirm the Suffix of the model number.

If the Main board is replaced, the Model and Serial number must be reinserted


into memory. See Model Number D/L.

1) Create an LG_DTV folder on the USB Flash Drive

USB Automatic Software Download InstructionsUSB Automatic Software Download InstructionsCurrently Installed Version

Software Version

found on the USB Flash

DriveDrive

File found on the USB Flash Drive

2) Copy new software (xxx.epk) to "LG_DTV" folder. Make sure to have correct software file.

3) With TV turned on insert USB flash drive3) With TV turned on, insert USB flash drive.4) You can see the message

TV Software Upgrade (See figure to right)5) Cursor left and highlight "START" Button and

push Enter button using the remote control. 6) You can see the download progress Bar.7) Do not unplug until unit has automatically

restarted.8) When download is completed, you will see

COMPLETE

* CAUTION: Do not remove AC power or the USB Flash Drive. Do not turn off Power, during the upgrade process.


COMPLETE . 9) Your TV will be restarted automatically.

Software Files are now available fromLGTechassist.com

Manual Software Download:Manual Software Download:

Prepare the Jump Drive as described in the USB Automatic Download section and insert it into either of the USB ports.p p pBring up the Customers Menu and scroll to OPTIONS.Press the FAV key 7 times to bring up the Manual Download Screen.

Highlight the Software update file g g pand press SELECT to begin the download process.

WARNING:Use extreme CautionUse extreme Caution when using the Manual Forced Download Menu. Any file can be downloaded when

Example of files foundOn the Jump Drive

selected and may cause the Main board to become inoperative if the incorrect file was selected.


Accessing the Service MenuAccessing the Service Menu

To access the Service Menu.1) You must have either Service Remote. )

p/n 105-201M or p/n MKJ391708282) Press In-Start3) A Password screen appears.4) Enter the Password.)

Note: A Password is required to enter the Service Menu. Enter; 0000Se ce e u te ; 0000

Note: If 0000 does not work use 0413.


MKJ39170828105-201M

1. Country Group (Press OK to Save) Country Group Code Country Group Country2. Tool Option Tool Option 1 Tool Option 2 Tool Option 3 Tool Option 4 Tool Option 53. Adjust White Balance:4. Adjust ADC: 4809 Component 1080p Component RGB5. EDID(AC3): RGB HDMI1 HDMI2 HDMI3 HDMI4

02USUS

24832302915636445251802

OK(8) OK

OKOKOK

OKOK (0x1D)

OK (0x4,0x5A)OK (0x4,0x4A)OK (0x4,0x3A)OK (0x4,0x2A)

IN SARTModel Name: 42LE5500-UASerial Number: 912KCLH1P752S/W Version: MICOM VersionBOOT VersionFRC VersionIR LED VersionEDID Version (RGB)EDID Version (HDMI)Chip TypeWireless Host Ver.Wireless B/B/ Ver.Vi-Fi VersionVi-Fi ChannelWi-Fi MAC : 00:E0:91:D1:0B:E1MAC Address : 00:E0:91:C6:A0:1BESN Num. : LGE-LE4200XXXX000A0C9037Local Dimming Ver.Debug Status

UTT : 37APP History Ver.:49324PQL DB:LGD_EF_LGT10_ALLxN42

1. Adjust Check2. ADC Data3. Power Off Status4. System 15. System 26. Model Number D/L7. Test Option8. External ADC9. Spread Spectrum10. Sync Level11. Wireless Ready12. Stable Count13. ODC Test14. Local Dimming

Adjust Check

: 08.00.11.01: 3.06.6: 1.02.20: f0.f0: c8: 0.01: 0.02: BCM 3549: 0.00.0: 0.00.0:1.0: 1

:0x0703:RELEASE

42LE5500 Service Menu First Page42LE5500 Service Menu First Page

24 October 2010 42LE5500 LCD-DV

Bring up the Service Menu using the Service RemoteAnd pressing In-Start enter password 0413. (May also be 0000).

Unit Total Time

SW Version

CountryGroup

Audio Mode

42LE5500-UA

42LE5500 Model Number Download Screen42LE5500 Model Number Download Screen



0. Model Name1. Serial Num.

Model Number D/L

Press OK to Save

912KCLH1P752

Bring up the Service Menu using the Service Remote.Scroll down to item 6. Model Number D/L to highlight.Press Select or Cursor Right.

Change the Model and Serial Number to match. To Change the Model Number Use the cursor right or left to select the area to change. Use the cursor up or down to change.Cursor right until there is no text cursor blinking.Scroll down to highlight Serial Number and change.

42LE5500 UTT Reset (IN START) Screen42LE5500 UTT Reset (IN START) Screen



0. Baudrate1. 2 Hours Off (On Timer)2. 2 Hours Off (Screen Mute)3. 15Min Force Off4. Audio EQ5. Audio Bass EQ6. A2 Threshold7. HDMI Sound(Port1)8. Lip Sync Adjust(ATV)9. Dimming10. Tuner Option11. Atten RF Signal12. UTT Reset13. Channel Mute14. Debug Status15. NVRAM Type16. HDEV17. Blue back18. China Cable SO19. Booster On (VHF)20. Booster Off (VHF)21. Booster On (UHF)22. Booster Off (UHF)

IN SART SYSTEM 1Model Name: 42LE5500-UASerial Number: 912KCLH1P752S/W Version: MICOM VersionBOOT VersionFRC VersionIR LED VersionEDID Version (RGB)EDID Version (HDMI)Chip TypeWireless Host Ver.Wireless B/B/ Ver.Vi-Fi VersionVi-Fi ChannelWi-Fi MAC : 00:E0:91:D1:0B:E1MAC Address : 00:E0:91:C6:A0:1BESN Num. : LGE-LE4200XXXX000A0C9037Local Dimming Ver.Debug Status

UTT : 37APP History Ver.:49324PQL DB:LGD_EF_LGT10_ALLxN42

9600OnOffOnOnOn11

HDMI Port10

OnEnhanced Ghost

OffReset

OnRELEASEEEPROM

OffOnOn0000

Scroll to (UTT Reset)

Press (Select)Reset changes to Doing

then back to Reset

Scroll to (System 1)

thenRight Cursor

: 08.00.11.01: 3.06.6: 1.02.20: f0.f0: c8: 0.01: 0.02: BCM 3549: 0.00.0: 0.00.0:1.0: 1

:0x0703:RELEASE

After Reset (Doing) has completed, Reset returns.After Exit the UTT Timer is

0

Unit Total Time

Changes to Doing

Service Menu: Downloading EDID Data Pg 1 of 2Service Menu: Downloading EDID Data Pg 1 of 2

1) Press ADJ key. 2) Select menu, Either PCM EDID D/L or AC3 EDID D/L


Service Menu: Downloading EDID Data Pg 2 of 2Service Menu: Downloading EDID Data Pg 2 of 2

3) Highlight Start then Press Select key

4) When Writing appearsDownloading in progress

5) Downloading Completethen Press Select key. Downloading in progress

When PCM EDID D/L was selected

When AC3 EDID D/L was selected

Note: When PCM is downloaded, AC3 will be N/G and when AC3 is downloaded PCM will be N/G. Thi th t h PCM i OK PCM di i i it d h AC3 i OK AC3 di i


This means that when PCM is OK, PCM audio is priority and when AC3 is OK, AC3 audio is priority.

4) Cursor Left to only highlight the briefcase

Accessing the Host Diagnostic Screen Accessing the Host Diagnostic Screen (Page (Page 1 of 2)1 of 2)

1) Place Television on the digital channel that

Use the Host Diagnostic screen to investigate the signal quality of a problem channel.

2) Bring up the Customers Menu and highlight Options.

) y g gon the left.

) gmay be showing problems.

3) The Option Menu appears.5) Press the (1) Key 5 to 8 times.


See next page for more details.

Wireless Host Ver:0.00.0Wireless B/B Ver:0.00.0RF Region Config : Not ConfiguredMedia Box Type : Not ConfiguredRF Frequency (Value):Auto (N.A.)Uplink RF Power gain (Value):Auto (Min 0)Downlink RF Power gain (Value):Auto Link Mode : UnicastRX MAC Address : ff:ff:ff:ff:ff:ffTX MAC Address : ff:ff:ff:ff:ff:ffWireless connection status:DisconnectedAverage SNR [db]:0.0(0)

Host Information

Memory

Host Release Version

FAT Status (Main)

Current Channel (Main)

DVI/HDMI StatusCant display this information now

Channel Info : Digital 19-2

Parental Control : Channel is not blocked

Host Diagnostics

Model Name : 42LE5500-UA (Liquid Crystal Display)

FLASH : 524288 KBDRAM : 524288 KBNVM : 128 KB

Firmware Version(MP) : 8.00.11.01(51822)Micom Version : 3.06.5Compile Date & Time : 20101112 & 15:17:49Compile User : kyuhae.lee

Center Frequency : 663.00 MHzPCR lock : LockedModulation mode : QAM 256Carrier lock status : LockedSNR : 40 dBSignal level : 100%

Half Page Move Page ExitCH

30

Understanding the Host Diagnostic Screen (Page 2 of 2)Understanding the Host Diagnostic Screen (Page 2 of 2)

October 2010 42LE5500 LCD-DV

Channel Selected

Software Version

Blocked or not Blocked

Channel Frequency

Program Clock Reference (Locked or No)Channel Type (8VSB, QAM 64, 256)

Channel (Locked or No)Channel Signal to Noise Ratio

Channel Signal Level (Above 80% good)

8VSB (Above 20 is good)QAM 64 (Above 24 is good)

QAM 256 (Above 30 is good)

Weight w/o Stand 36.8 lbsWeight with Stand 43 lbs

42LE5500 Product Dimensions42LE5500 Product Dimensions

7.7/8"200mm

24.13/16"629.92mm

40"1016mm

Remove 4 screws to remove stand for

wall mount

20.7/16"510mm

27.3/16"690.88mm

1.3/16"30.48mm

10.5/8"269.24mm

7.7/8"200mm

5.9/16"142mm

11.5/16"288mm

2.3/8" (60.96mm)

Center

There must be at least 4 inches of Clearance on all sides

31

17.5/16"440mm

12.3/8"314.96mm

Model No.Serial No.

Label

WattageLocal Dimming TBDFull White TBDStand By 0.1W


DISASSEMBLY SECTIONDISASSEMBLY SECTION

Disassembly:This section of the manual will discuss Disassembly, Layout

(Ci it B d Id tifi ti ) f th 42LE5500 LCD Di t Vi T l i i(Circuit Board Identification) of the 42LE5500 LCD Direct View Television.

Upon completion of this section the Technician will have a better understanding of the disassembly procedures, the layout of the printedunderstanding of the disassembly procedures, the layout of the printed

circuit boards and be able to identify each board.


Removing the Back Cover Removing the Back Cover

Remove the 28 screws indicated.Pay attention to the size and type of screwPay attention to the size and type of screw

as there are many different types.Putting in an improper screw when reassembling may Cause damage.

The AC CordDoes Not unplugRemove plastic

cover.cover.

The Stand Bracket has a plastic cover Not Shown that must be removed to


The Stand has to be removed before removing the back.expose the screws.

Warning: The Frame has

Clips hold the front glass in place, use caution. Add screws while servicing.Circuit Board LayoutCircuit Board Layout

Warning: The Frame has very sharp edges

To LEDs

Main BoardPower Supply Main Board(SMPS)

LVDS Cables

Panel Connection Points

InvisibleIR/LED Soft Touch InvisibleLG Logo


InvisibleSpeaker Right

IR/LED Board

Soft TouchKeyboard

InvisibleSpeaker Left

LG Logo Board

MAINBOARD

POWERSUPPLY

Speaker (Front Left)

AC In

IR LED

42LE5500 Connector Identification Diagram42LE5500 Connector Identification DiagramTFT PANEL


Speaker (Front Right)Soft Touch Keys

p/n: EBU60904603p/n: EBR66101301p/n: EBU60904602

p/n: EBR64966201

p/n: EAJ60871201

p/n: EAB60961501 p/n: EAB60961501p/n: EAV60793302p/n: EBR64966801

p/n: EAY60803101p/n: EAY60803201

n/c

n/c

SK101

P204

P7501 P7500 P8000

P8200P8800

J1J2

J3

ToTFT

Panel

If the Panel is replaced, reset the UTTTime. Service Menu, System 1 Item 12

P205

P201

To LEDs

White Plug

Black Plug

Power Supply Power Supply Board RemovalBoard Removal

P201Board is Thin be

p/n EAY60803101

Press in gently on the two

Board is Thin, be careful not to flex.

Disconnect P201, P204,

P205 and AC

tabsto release

lock

In SK101.SK101 fits very snug into its connector.

Remove the 6 screws indicated

SK101

by the arrows.AC In

Press in on thetwo tabs


to release lock

Removing the Main BoardRemoving the Main Board Flip the locking tab upward, pull the LVDS ribbon out.p/n EBU60904603

Disconnect P7500, P7501, P8000, P8200 and P8800

P7501 P7500P8000

Remove any tape holding down any cables.

Remove the 7 screws N/C

Press in on the side release

tabs to remove.indicated by the arrows.

Decorative Metal PlateRemove decorative N/C

NOTE: Always check on

plastic and remove the board. After removing the Main, there

are tabs sticking through the Main board holding the Metal

plate in place.

top and behind the Large ICs. And look for a piece

of Chocolate(Heat Transfer Material).

Be sure to transfer to new Board if present

P8800 P8200


new Board if present.

Removing Front IR BoardRemoving Front IR BoardDisconnect J1, J2 and J3 connectors.

Press upward on the two tabs at the top. Tilt the board downward.

TabTab

p p

Lift straight up To Clear the Tabs at the bottom.

J3

Tab

IR board / Intelligent SensorJ3

J1

p/n EBR64966201

Tab Tab


p/n EBR64966201

TROUBLESHOOTING SECTIONTROUBLESHOOTING SECTION

Troubleshooting:gThis section of the manual will discuss troubleshooting.

Upon completion of this section the Technician will haveUpon completion of this section the Technician will have a better understanding of how to diagnosis and resolve

problems.


POWER SUPPLY SECTIONPOWER SUPPLY SECTIONThis switch mode power supply develops Stand By 3.5V at all times when AC is applied.At power on, it develops 12V and 20V for the Main board.It develops 120V for the LED Backlights.

This power supply draws less than 1 watt during stand by mode. The fuse F101 and F103 reads 7.6V (from hot ground) during this time.

When the controller chip receives the PWR-ON commandWhen the controller chip receives the PWR ON command 3.36V via P201 Pin 1, the primary section increases its current supplying ability. Both Primary fuses F101 and F103 now read a little more than 395V. T102 delivers AC to D206 which develops the 120V for th LED b kli htthe LED backlights.

P201 Connector: (To Main Board)12V (11.43V) is routed out P201 pins 17, 19 and 21 and 20V (21.27V) is routed out P201 pins 2, 3 and 4. ( ) p ,

P204 Connector: (To Panel LEDs)120V is routed out P204 pins 1 and 12.

P205 Connector: (To Panel LEDs)


P205 Connector: (To Panel LEDs)120V is routed out P205 pins 1 and 12.

Power Supply (SMPS) Board LayoutPower Supply (SMPS) Board Layout p/n EAY60803101

F101F1013.15A/250V

F1031A/250V

STBY 7.6VRun 396V

From Hot Gnd

F100 5A/250V5A/250V

F1021A/250V

AC Protect

Hot Ground Shock Hazard


42LE5500 Power Supply Start Up Sequence42LE5500 Power Supply Start Up Sequence

42

Inverter OnStarts the Inverters

Stand By 3.5V

Remote or Power Button Key

MAIN BOARD

RL_ONInvOn

Stand By3.5V Reg

2 5 66 8

4

5

Primary side fuses:Stand-By 7.6V Run 396V (Hot Gnd)

3

12V 20V

12V

At point TV is in Stand-By state. Energy Star compliant.0 .1 Watts

3

Other Regs

LCD PANELTo Panel Backlights

120HzManipulates Backlight

LEDsLow = Bright

RL_

On

2

No AC Det in this

model

After Mute ReleasedLVDS Video

Ft IRKey

120V

Model 1_Opt1 Panel Control

INV_CTL

Microprocessor IC8101

RL_ON

And Tru-Motion LVDS Video

Q8004

P201

T510 &Rectifier P205

Pow

er O

n

Power On

5

P204

120V

P8000

Soft Touch KeyP8200

Inve

rter O

n

P7500Reset

GeneratorC8108R8184

1AC In

3.5V_ST

P-D

IM

8

4

P7501

PanelVCC 12V

IC9103

3.3V, 16V, -5V,

26V,

DC toDC 7

5

7

Key 1 or IR

7

VideoProcessor

IC900

IC9102HVDD

7.8V

VCC 3.3V, VDD 16V, VGL -5V, VGH 26V,

HVDD 7.8V

IC93021.8V_L/ Dimming

7

SINMOSI, CLK12 Blocks

9

9

9


POWER SUPPLY (SMPS)POWER SUPPLY (SMPS)

BridgeRelaysT102D206

6

5 12V/20V Regulators

On BoardInverter

8

9

6

Local andGlobal Dimming

Local andGlobal Dimming

5

P-DIM1 (PWM-DIM)Pulse Width Dimming

Global DimmingManipulated by:

Cust Menu for Backlightand

Picture ContentManipulate P-DIM

Local Dimming (SIN)

IC9301Dimming

IC

8

8

22182~4

SeeNote 1:

IC8801Audio Amp

171921

19~12 16 Note 1:12V TURNS ON:IC8000 5V_USBIC8003 5V_NormalIC8005 3.3V_NormalIC8903 +3.3V_MEMCIC8902 +1.26V_MEMCMEMC=Motion Estimated Motion CompensatedFor Video Processor

Right Side Panel

Driver Board

Left Side Panel

Driver Board

P-DIM9

9

2

7

GlobarDimming

V-SYNC

9

23

0.38V~3.3VPWM-DIM PWM-DIM

0.09V

PWM-DIM (PWM Dimming) can vary according to incoming video IRE level, OSD Backlight setting and Intelligent Sensor (room light condition). Range 0.37V to 3.3V.

42LE5500 Television Turn On Commands Circuit Drawing42LE5500 Television Turn On Commands Circuit Drawing

R8019100

11.43V

Gnd

Gnd

Gnd

Gnd

3.36V

ERR OUT

PWR

INV_CTL

SMPSP201

R25

11

MAIN BoardP8000

3.5V

Gnd

1

65

87

109

1211

1415

19

17

21

18

24

22

1

65

87

109

1211

1415

19

17

21

18

24

22

Gnd

L8003

L8002+12V

C8001 100uF

R800010K

10

Q8005+3.3V_Normal

INV_CTL

S

2

6

D

7

Q8004

L8015

Panel_Vcc (12V)

3.36V

GQ8003

Model_Opt_1

1.8V

+12VR8010 10K

C8000100uF

+3.5V_ST

RL_ON

GPIO 09

3.28V

43

Q8002

L8000

+3.5V_ST

INV_On

PWR-ON IC8101Micro

RL_ON

Power Det 14

Reset40

Key 1 25

Key 2 26

PowerOn/Off 2_220

R80044.7K

3.5V

3.5V

3.5V

Q80010V

36

R8060 10K

+3.3V_Normal

Reset

Gnd13 13

16 160.02V

23 233.3V

Gnd (Not Used)

Q8000

R803210K

R818722

R818447K C8108

0.1uF

IC900BCM

R1041 0R8027 0

R817822

IR 16

R813522

R8103100

R800147KR8011 1.8K

To IC9103 DC to DC Conv T-CON

+12VL8013

IC8005

Power_On/Off2_2R8176

22K

R80261K

0.68V

R8003 22K

11.8V11.79V

11.8V

3.36V 8

0.66V0V

3.36V

3.3V 0V

0V

3.1V

21.27V

11.9V

R813422


32

432

4

L8005+20V

C802468uF

20V

21.27V

12V

P-DIM: Digital Dimming (Variable)

SBY3.5V

20 20

T6 M2_MOSI

IC9301Dimming

R9347 22M2_MOSI

R8076 0

SIN

21.27V

21.27V

11.43V

11.43V

U5

R935022VSYNC / R_VS

SCLK

R8078 0

VSYNC

SIN

R6 M2_SCLK

R_VSR9346 22R8077 0

M2_SCLKSCLK

VSYNC

(Data) 3.25V p/p Data

3.64V p/p

3.76V p/p

IC8007IC8008

3

1 1

2

2

3

4

4

4

4

5

6

6

7

7

88

8

9

9

9

9

9

4

1

AC Should not be applied at any time while adding jumpers or While unplugging connectors as damage to the circuit Board

Power Supply Board Low Voltage Test 1Power Supply Board Low Voltage Test 1

While unplugging connectors as damage to the circuit Board may occur.

a) When AC is applied, the SMPS MUST be producing STBY 3.5V on pins 9, 10, 11 or 12 of P201.

If 3.5V Standby is not being generated, the SMPS is defective and must be replaced. There is no need to continue with the next test.But, make sure AC is arriving at the connector SK101.

(b) Unplug P8000 on the Main Board to make insertion of the Jumpers easier. Use P700 Side to insert resistors

TEST 1:

Pin 1 is the Brown Wire

(1) Add a jumper between (3.5V STBY) pin 7, 8, 9 or 10 and Pin 1 (PWR_ON). Apply AC. This will turn on the power supply, relays will click.a) Check that the 20V (21.3V) and 12V (11.43V) power supplies are turned on,

P201 (12V pins 17, 19 and 21) P201 (20V pins 2 3 and 4) P201 (20V pins 2, 3 and 4) P204 and P205 (120V pins 1 and 12) to the Panel. (Or check D206 + lead)

(2) Remove AC powerNo Backlights during this test

You can however ground each individual driver and turn on each block one at a time for a quick backlight block


You can however, ground each individual driver and turn on each block one at a time for a quick backlight block test. (Youll have to look from the back of the panel to see if the block turns on because the Panel is off.

Continue if the 1st test was OK. Leave original jumper in place.

Power Supply Board Backlights Test 2Power Supply Board Backlights Test 2

Leave original jumper in place.

(3) Add another jumper between (STBY_3.5V) pin 9, 10, 11 or 12 and Pin 18 (INV_On).

(4) Apply AC Power. Simulating a Power and Backlight On command.

Backlights Normal:) If l th b kli ht h ld ta) If normal, the backlights should turn on.

SMPS OK, Inverter OK.

Backlights Abnormal:a) Recheck all connections

Pin 1 is the Brown Wire

a) Recheck all connections.b) Confirm the DRV_ON line pulling up to at least 3V. c) Check the connections to the Panel.

If the DRV On command is pulling up to 3V and the 120V is being generated _ p g p g gfrom D206 + leg, see the Inverter Section of the Power Supply for additional checks. Note: If either P204 or P205 is disconnected, the backlights will come on,

The Error line will go high, then the backlights shut off in 4~6 seconds.


REMOVE AC POWER:

42LE5500 2 Sided Edge Lit Panel (V5)42LE5500 2 Sided Edge Lit Panel (V5)


ONE STRIP (Board)

1 Block 1 Block 1 Block

Connector 4 pin

Front Side Panel View

1 Block

120V

32V p/p

LED Drive Signal 50 IRE

10mSec

DriverOn

SMPS6.32V drop per/LED

GlobalAnd

LocalDimmingControl

P204 or P205

TWO SIDED EDGE 2010

Input from SMPS InverterConnector Connector

Connector ConnectorOne LED can be tested with a Diode Check using a DVM. Forward biased, the LED should light.

Each Connector has (3) Block driver pins and (1) 120V Input pin

120VBlock

Control Signals(Drive)

Connector

LED 228 Total LEDs4 Boards (Strips)57 LEDs per/board

12 Total Blocks (6 on Top, 6 on Bottom)

3 Blocks per/board19 LEDs per/block

E

B

C

E

B

C

E

B

C

E

B

C

E

B

C

E

B

C

E

B

C

E

B

C

E

BC

E

BC

E

BC

E

B

C

P204

P205

These drivers ground the LED blocks. (12 Total). If the 120V is present on Pins 1 and 12 of P204 and P205 you can ground these test points to turn on a block.

1V (100 IRE)30V (0 IRE)

42LE5500 Inverter Part of the SMPS42LE5500 Inverter Part of the SMPS


Gnd

Gnd

120V

120V

120V

120V

n/c

n/c

n/c

n/c

n/c

n/c

Local Dimming OnL-DIM (SIN)

Local Dimming OffL-DIM (SIN)

32V p/p

LED Drive Signal 50 IRE

3.64V p/p V-Sync Signal

3.25V p/p

3.25V p/p

*1V~30V LED Drive

*1V~30V LED Drive

*1V~30V LED Drive

*1V~30V LED Drive

*White 100 IRE to Black 0 IRE

INVERTER Section of the

SMPS

Inverter Top Left Connector1 VDD-33 3.5V2 VLED-RANGE 0V3 Gnd Gnd4 +12VS 12.44VPin 17-19-21 P2015 Gnd Gnd6 +3.5VS 3.57VPin 9-12 P201

Inverter Center Left Connector1 INV_ON 3.28VPin 18 P2012 Gnd Gnd3 Gnd Gnd4 SCLK 0.09VPin 20 P2015 FB_STR_VF 1V6 P-DM1 1.9VPin 22 P201

Inverter Bottom Left Connector1 Error 0VPin 24 P2012 (L-DIM) SIN 3.3VPin 23 P2013 POWER_ON 3.35VPin 1 P2014 VSYNC_IN 0VPin 16 P2015 Gnd Gnd6 Gnd Gnd

Pin 23 P201

Pin 23 P201

Pin 16 P201

3.76V p/p SCLK Signal

Pin 20 P201

100uSec

10mSec

100uSec

Power Supply Connector P201 Voltage and Diode CheckPower Supply Connector P201 Voltage and Diode Check

P201 Connector SMPS to Main P8000 P201 ConnectorP201 Label

Pin Label STBY Run Diode Check

24 ERROR Gnd Gnd *1.45V

23 L-DIM (SIN) 0V 3.3V Open

Odd pins are on

front row

22 PDIM1 0V 0.38V~3.3V Open

21 12V 0V 11.43V 0.178V

20 SCLK 0V 0.09V Open

19 12V 0V 11 43V 0 178V

1

19 12V 0V 11.43V 0.178V

18 DRV_ON (INV-ON) 0V 3.28V Open

17 12V 0V 11.43V 0.178V

16 V SYNC 0V 0 02V O

(1) PDIM1 Pin 22 can vary according to incoming video IRE level, OSD Backlight setting and then Intelligent Sensor

16 V_SYNC 0V 0.02V Open

13-15 Gnd Gnd Gnd Gnd

9-12 3.5V 3.57V 3.5V Open

5-8 Gnd Gnd Gnd Gnd g g g(room light condition) Output from the Video Processor IC900. Range 0.37V to 3.3V. .

2-4 20V 0V 21.27V 1.10V

1 PWR-ON 0V 3.36V 1.02V

PDIM13 66V p/p 50IRE

*Pin 24 is grounded on the Main Board


Diode Mode values taken with all Connectors Removed3.66V p/p 50IRE

Power Supply Connector P204 / P205 Voltage and Diode CheckPower Supply Connector P204 / P205 Voltage and Diode Check

P204 "SMPS" to The Panel" P204Pin Label STBY Run Diode Check

12 02.A 0V 120V Open


12 04.A 0V 120V Open

P205 "SMPS" to The Panel"

12 02.A 0V 120V Open

11 n/c n/c n/c Open

10 02-1C 0V (1)1V~30V Open

9 02-2C 0V (1)1V~30V Open(1)

12 04.A 0V 120V Open

11 n/c n/c n/c Open

10 04-1C 0V (1)1V~30V Open

9 04-2C 0V (1)1V~30V Open(1)

1

P2058 02-3C 0V (1)1V~30V Open

7-6 n/c n/c n/c Open

5 01-3C 0V (1)1V~30V Open

4 01-2C 0V (1)1V~30V Open

8 04-3C 0V (1)1V~30V Open


5 03-3C 0V (1)1V~30V Open

4 03-2C 0V (1)1V~30V Open

1

3 02-1C 0V (1)1V~30V Open

2 n/c n/c 0V Open

1 01.A 0V 120V Open

3 03-1C 0V (1)1V~30V Open

2 n/c n/c 0V Open

1 03.A 0V 120V Open

(1) The drive signal changes due to the brightness level of the backlights. Low indicates Bright. High indicates Dim.


Diode Mode values taken with all Connectors Removed

Power Supply Connector SK101 and AC Fuses Voltage and Diode CheckPower Supply Connector SK101 and AC Fuses Voltage and Diode Check

SK101 "SMPS" to AC INF100

6.3A/250VF102

1A/250V


EL1 L120Vac

OL

EL3 N OL

F100

AC IN

F102

AC

EL3 N OL

AC Voltage Readings (From Hot Ground)Pins 1 and 2 for STBY and RUN.


F100 or F102 (Diode Check)F100 or F102 (Diode Check)

Red or Black Lead on Fuse (Open)Other Lead on Hot Ground

L N

Bottom Right of SMPS


SK101

Power Supply F101 and F103 Voltage ChecksPower Supply F101 and F103 Voltage Checks

F1003.15A/250V

F1031A/250V

From Hot GndSTBY 7.6VRun 396V

From Hot GndSTBY 7.6VRun 396V

Run 396V

If the set was on and then turned off into the Stand-By condition, the voltage takes a very long time to bleed down to the reading given here.


MAIN BOARD SECTIONMAIN BOARD SECTIONThe Main board receives its operational B+ from the Power Supply via P8000. There are two LVDS cable feeds that are output from the on-board T-CON (TFT Driver) section directly to the Panel. These carry the duel 12 bit LVDS Video and TruMotion Video equaling a 120Hz video signal. These signals have already been prepared for the Panels Left and Right boards. The Main board also includes the Tuner, Audio and Audio/Video inputs and selection circuits.

Input Voltages from SMPS.STAND-BY

STBY 3.5V (P8000 pins 9~12)

The Main board also develops several B+ sources on the board.

RUN 12V pins 13 and 14 20V pins 17 and 18.

LVDS Panel VCC (12V Not generated but switched

STAND-BY VOLTAGES 3.3V_ST (Voltage direct from SMPS).

GENERAL 5V_Normal (Made from 12V In). 3.3V_Normal (Made from 12V In). 5V USB (Made from 12V In).

Panel_VCC (12V Not generated, but switchedfrom the 12V arriving from the SMPS).

TUNER and VSB CIRCUIT 3.3V_TU (Made from 3.3V_Normal). 1.26V_TU (Made from 3.3V_TU).

BCM IC900 Micro/Video Processor 3.3V_ST, 1.2V, D1.5V, D1.8V

IC9301 Tru-Motion and Dimming IC 1.26V MEMC, 1.5V MEMC,

WIRELESS VOLTAGES to JK8700 20V (Switched from 20V from SMPS)

AUDIO IC8801

1.26V_MEMC, 1.5V_MEMC,and 3.3V_MEMC

T-CON IC9001 3.3V_VCC, -5V_VGL, 27V_VGH, 16V_VDD and HVDD (7.8V)


1.8V (Made from 3.3V_Normal). HDMI VOLTAGES (Q200) 1.8V_HDMI (From D1.8V)

Main Board LayoutMain Board Layout

P7501

To Panel

P7500

P8000To SMPS

VIDEO PROCESSOR IC900, T-CON IC9001 and

Tru-Motion IC9301

See next page for component

identification IC901

IC9301

p/n:EBU60904603

Tru-Motion IC9301 run Hot.

This is normal.

P9000n/c

identification IC901

USB 1

P8100n/c

IC900

US

USB 2

Component InThese connectors are

Mini plug type

LAN Headphone

P8800To Speakers

Wireless Remote

Headphone

HDMI


To SpeakersP8200 To Front IR


42LE5500 Main Board (Front and Back Side) Component Layout42LE5500 Main Board (Front and Back Side) Component Layout

54

E

C

B A1

C

A2

Q D

(1) P-DIM Pin 20 can vary according to incoming video IRE level, OSD Backlight setting and then Intelligent Sensor (room light condition) Output from the Video Processor IC900. Range 0.69V to 3.3V.

SW8100Micro Reset

SW1000Video Reset

SW9300Tru-Motion

Reset

10MHz

Q?

D

G S

A-CA

C

MAIN BOARDp/n: EBU60904603

P8200

IC900Video Processor

LGE3549XQ

P8800

Q8200

Q8201

Q8700

IC8300

L8805L8804

HDMISelectIC8801

IC8800

IC8004Q8800

Micro

IC8101

SW1000

SW8100X8100

P90

00n/

c

X900012Mhz

IC1000IC901

IC9001T-CON

LGE7378A

X930025Mhz

IC9300

SW9300

P7501 P7500

IC9100L9100

IC9102

L9102

L9101

IC9103

A-CA

C

D9101

D9102IC9302

L9301

IC8901IC8900 L8904

3

2 1

3

2 1

Q8004Q8005

Q8001

Q8003IC8008

IC8007

L8905IC8903IC8902

L8012IC8002 IC8001

IC8003

L8015

IC8005

P8000

L8010L8009

P9000Gamma

IC605IC603IC301

IC302

L8004 USB1

54MHz X1001

USB2

IC700

IC300Q300

TU700TDVJ-H031F

18. IF p17. IF n16. IF AGC15. Reset14. 3.3V13. 1.26V12. GND11. CVBS10. NC 9. SIF

8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V

2. NC 1. NC

HP

HDMI

D8310

ComponentComposite

IC8000

Digital Video

Analog

Tuner B+

Tuner DataTuner Clock

Audio

A2 A1

C

LAN

X810132.768Khz

IC9301LG5111

Q901

IC602IC606IC604

Q702Q701

IC8200

IC8401

IC8400Q8304

Q8301

D8307 Q8303Q8300

Q8701IC8700

Q8205Q8203

Q8305Q8302

D8306

DSG

Q200

G

S

B

D

Q8308

D8312

IC8100

IC9000

IC9303IC9101

Q8000 Q80021

23

D8309

P8200 Connector "MAIN Board" To CON1 "IR Board"

Pin Label STBY Run Diode Check1 SCL 3.56V 3.5V Open2 SDA 3.56V 3.5V Open3 Gnd Gnd Gnd Gnd4 KEY 1 3.32V 3.3V 1.9V5 KEY 2 3.29V 3.3V 1.9V6 3.5V_ST 3.56V 3.47V 1.24V7 Gnd Gnd Gnd Gnd8 LED_LOGO 0V 0V Open9 IR 1.63V 1.6V Open10 Gnd Gnd Gnd Gnd11 +3.3V_Normal 0V 3.34V 0.52V12 LED_R/BUZZ 0V 0V Open

P8000 "MAIN Board" Connector To P201 "SMPS Board"

Pin Label STBY Run Diode Check1 PWR-ON 0V 3.36V Open

2-4 20V 0V 21.27V Open

5-8 Gnd Gnd Gnd Gnd

9-12 3.5V 3.57V 3.5V 1.24V


16 V-SYNC 0V 0.02V 1.06V

17 12V 0V 11.43V Open

18 INV-ON 0V 3.28V 1.62V

19 12V 0V 11.43V Open

20 SCLK 0V 0.09V 1.06V

21 12V 0V 11.43V Open

22 P-DIM 0V 0.38V~3.3V Open

23 L-DIM (SIN) 0V 3.3V 1.05V

24 ERROR 0V 0V Gnd

10.62VEach Pin

3.3V_NormalRL_ON

Panel _CTL

Panel _DC-DC

VDD_7.8V

INV_ON

3.3V_MEMC1.26V_MEMC

1.5V_MEMC

5V_Normal

D1.2V & A1.2V

5V_USB 5V_USB2

5V_USB1

+1.26V_TU

DDR_VTT

1.8V_AMP

1.8V_L/Dimming

A2.5V

Power Det

R- R+ L- L+


42LE5500 Main Board (Front) Component Layout42LE5500 Main Board (Front) Component Layout

55

E

C

B A1

C

A2

Q D

SW9300Tru-Motion

Reset

SW8100Microprocessor

Reset

SW1000Videoprocessor

Reset

D

G S

A-CA

C


Q?

P8200


LGE3549XQ

P8800

Q8200

Q8201

Q8700

IC8300L8805L8804

HDMISelectIC8801

IC8800

IC8004Q8800Micro

IC8101 SW1000

SW8100X8100

P9000Update

X900012Mhz

IC1000

IC901

IC9001T-CON

LG7378A

IC9301LG5111RX/TX

X930025Mhz

IC9300

SW9300

P7501 P7500

IC9100L9100

IC9102

L9102

L9101

IC9103

A-CA

C

D9101

D9102IC9302

L9301

IC8901IC8900 L8904

3

2 1

3

2 1

Q8004Q8005

Q8001

Q8003

IC8008

IC8007

L8905IC8903IC8902

L8012IC8002 IC8001

IC8003

L8015

IC8005

P8000

L8010L8009

P9000Gamma

IC605IC603IC301

IC302

L8004 USB1

54MHz X1001

USB2

IC700

IC300Q300

TU700TDVJ-H031F


8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V

2. NC 1. NC

HP

HDMI

D8310

ComponentComposite

IC8000

Digital Video

Analog Video

Tuner B+


Audio

A2 A1

C

R- R+ L- L+

42LE5500 Main (Front Side) Component Voltages

IC300 Earphone Amp IC700 (+1.26V_TU) IC8002 (D1.8V) IC8005 (+3.3V_NORMAL) IC8902 (+1.26V_MEMC) IC9102 DC to DCPin Pin Regulator Pin Regulator Pin Regulator Pin Regulator Pin HVDD T-CON[1] 0V [1] 0V (Gnd) [1] 5V [1] 0V (Gnd) [1] 0V (Gnd) [1] 0V (Gnd)[2] 0V [2] 1.26V (Out) [2] 3.34V (In) [2] 11.8V (In) [2] 11.8V (In) [2] 11.72V (In)[3] 0V [3] 3.3V (In) [3] 1.8V (Out) [3] 0V (Gnd) [3] 0V (Gnd) [3] 11.72V (In)[4] 0V [4] Gnd [4] 0.8V [4] 0.8V [4] 3.25V[5] 0V IC1000 SOC Reset [5] Gnd [5] 0.86V [5] 0.7V [5] 3.2V[6] 3.3V Pin Generator [6] 0.9V [6] 3.36V (PWR On/Off2 Ctl) [6] 3.36V (PWR On/Off2 Ctl) [6] 0V[7] 3.3V [1] 3.32V (In) [7] 0.9V [7] 3.36V (Out) [7] 1.3V (Out) [7] 0V

[8] (-1.8V) [2] 0V (Gnd) [8] 1V [8] 3.36V (Out) [8] 1.3V (Out) [8] 11.7V[9] (-0.8V) [3] 3.3V (Out) [9] 2.38V [9] 0V (Gnd)

[10] Gnd [10] 3.36V (PWR On/Off1 Ctl) IC8007 Power Det Gen IC8903 (+3.3V_MEMC) [10] 1.13V[11] 0.9V IC8000 5V Regulator Pin (+12V and +3.5V) Pin Regulator [11] 0V (Gnd)[12] 1.8V Pin for USB IC8003 (+5V_NORMAL) [1] 0V (Gnd) [1] 0V (Gnd) [12] 0V (Gnd)[13] 3.3V [1] 11.79V (In) Pin Regulator [2] 3.6V (In) [2] 11.8V (In) [13] 0V (Gnd)[14] 3.3V [2] 5V (Out) [1] 0V (Gnd) [3] 3.5V (Out) [3] 0V (Gnd) [14] 7.7V[15] Gnd [3] 5V (Out) [2] 11.8V (In) [4] 0.8V [15] 7.7V (HVDD)[16] 0V [4] 10.5V [3] 0V (Gnd) IC8008 Power Det Gen [5] 0.8V [16] 0V (Gnd)

[5] 3.3V [4] 0.8V Pin (+24V) [6] 3.36V (PWR On/Off2 Ctl)IC301 Switched [6] 0.8V [5] 0.86V [1] 0V (Gnd) [7] 3.3V (Out) IC9300 Reset for

Pin 5V for USB 2 [7] 4.99V [6] 3.37V (PWR On/Off2 Ctl) [2] 3.6V (In) [8] 3.3V (Out) Pin LG5111[1] Gnd [8] 0V (Gnd) [7] 5V (In) [3] 3.7V (Out) [1] 3.32V (In)[2] 5V (In) [8] 5V (In) IC9100 P-GAMMA [2] 0V (Gnd)[3] 5V IC8001 D1.2V and A1.2V IC8800 (+1.8V_AMP) Pin Chip [3] 3.34V (Out)[4] 3.3V Pin Regulator IC8004 A2.5V Regulator Pin Regulator [1] 3.3V[5] 3.3V [1] 0V (Gnd) Pin for USB [1] 0V (Gnd) [2] 0V (Gnd) IC9302 (1.8V_L/Dimming)[6] 5V (Out) [2] 3.3V [1] n/c [2] 1.8V (Out) [3] 3.3V (In) Pin Regulator[7] 5V (Out) [3] 0V (Gnd) [2] 3.26V (In) [3] 3.295V (In) [4] 0V (Gnd) [1] 0V (Gnd)

[8] n/c [4] 1.2V [3] 3.26V (In) [5] 6.8V [2] 11.8V (In)[5] 3.3V [4] n/c IC8901 (+1.5V_MEMC) [6] 6.8V [3] 0V (Gnd)

IC302 Switched [6] n/c [5] n/c Pin Regulator [7] 15.3V [4] 0.8VPin 5V for USB 1 [7] 4.46V [6] 2.55V (Out) [1] 0V (Gnd) [8] 15.3V [5] 0.76V[1] Gnd [8] 3.3V [7] 0.8V [2] 1.5V (Out) [9] n/c [6] 3.34V (PWR On/Off2 Ctl)( ) ( )[2] 5V (In) [9] 3.3V [8] 0V (Gnd) [3] 3.3V (In) [10] 13.47V [7] 1.8V (In)[3] 5V [10] 3.3V [11] 12.75V [8] 1.8V (In)[4] 3.3V [11] 1.2V Q8005 INV_ON Q8306 HDMI [12] 11.8V[5] 3.3V [12] Gnd Pin Driver Pin Det [13] 10V D9101 VGH/VDD[6] 5V (Out) [13] 3.3V B 0V (INV ON) En B 0V [14] 5.96V Pin Rectifyer[7] 5V (Out) [14] 0.8V C 3.1V (Out) C 3.3V [15] 4.06V A 15.4V

[8] n/c E Gnd E Gnd [16] 15.3V AC 22.2V[17] 0V C 27.4V (VGH)

Q300 Earphone Mute Q8003 PANEL_VCC Q8200 IR Buffer Q8307 HDMI [18] 2.96VPin L Out Pin Control 2nd Driver Pin 2nd Pin Det [19] 2.33V D9102 VGL/VCC

B 0V B 0.679V B 0.02V B 0V [20] 3.3V (In) Pin RectifyerC 3.3V C 0V C 3.4V C 4.18V A (-5V VGL)E Gnd E Gnd E Gnd E Gnd AC (-1.9V)

C 0VQ8001 PANEL_VCC Q8004 PANEL_VCC Q8201 IR Buffer Q8700 Wireless PWR Q8800 AMP_MUTE

Pin Control 1st Driver Pin Switch Pin 1st Dongle Out Turns on Q8701 Pin Pin 25 IC8801B 0V S 11.8V (In) B 0V B 0.66V (0.0V Dongle In) B 0VC 0.68V G 1.8V (Enable) C 3.3V C 0.14V (24V Dongle In) C 3.336VE Gnd D 11.8V (Out) E Gnd E Gnd E Gnd



42LE5500 Main (Back Side) Layout42LE5500 Main (Back Side) Layout

57

E

C

B A1

C

A2

Q D


Q901

IC602IC606 IC604


8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V

2. NC 1. NC

Digital Video

Analog Video

Tuner B+


Audio

TU700TDVJ-H031F

Q702

Q701

Rubber

IC8200

IC8401

IC8400Q8304

Q8301D8307

Q8303 Q8300D8309

Q8701IC8700

Q8205

Q8203

Q8305 Q8302D8306

Rub

berD

S

G

Q200

G

S

B

D

Q8308

D8312

IC8100

IC9000

IC9003

IC9001

Rubber

Rubber

Q8000

Q80021

23

42LE5500 Main (Back Side) Component Voltages

IC602 D1.8V IC8400 RGB IC8700 Wireless Q200 (1.8V_HDMI) Q8203 IR Wireless PassPin Regulator Pin H/V Sync Pin Buffer Pin Switch Pin 2nd Driver[1] 0V (Gnd) [1] 1.9V [1] 0V (3.3V Dongle In) S 1.83V (Out) B 0V[2] 3.29V (PWR On/Off1 Ctl) [2] 1.9V [2] 3.3V (0.3V Dongle In) G 3.35V (PWR On/Off2 Ctl) C 3.3V[3] 0.9V (DDR_VTT) [3] 4.4V [3] n/c D 1.83V (In) E Gnd[4] 0.93V [4] 0V [4] n/c[5] 1.83V [5] 0.9V [5] n/c Q701 Tuner SIF[6] 3.38V (In) [6] n/c (4.5V) [6] Gnd Pin (Sound) Buffer Q8205 IR Wireless Pass[7] 1.8V (Out) [7] 0V (Gnd) [7] Gnd B 0.16V Pin 1st Driver[8] 0.91V (DDR_VTT) [8] n/c (4.5V) [8] Gnd C Gnd B 0.6V

[9] n/c (1.9V) [9] n/c E 0.83V C 0VIC8100 EEPROM [10] n/c (1.9V) [10] 0.02V E Gnd

Pin Micro [11] n/c (4.5V) [11] 0V Q702 Tuner Video[1] 0V (Gnd) [12] 0.9V [12] 3.3V Pin (Analog) Buffer Q8300, 2 HDMI 2[2] 0V (Gnd) [13] 0.9V [13] 0V (3.3V Dongle In) B 2.05V Pin Det[3] 0V (Gnd) [14] 5V [14] 3.3V C 2.75V B 4.2V[4] 0V (Gnd) [15] 3.3V E Gnd C 0V[5] 3.37V IC8401 EDID Data [16] 3.3V E Gnd[6] 3.37V Pin PC Q901 FLASH_WP[7] 0V (Gnd) [1] 0V (Gnd) IC9303 EEPROM Pin for IC901 Q8303, 4, 5 HDMI 3[8] 3.37V [2] 0V (Gnd) Pin for LG5111 B 0V (Flash_WP) Pin Det

[3] 0V (Gnd) [1] 0V (Gnd) C 3.36V B 0VIC8200 RS232 [4] 0V (Gnd) [2] 0V (Gnd) E Gnd C 4.2V

Pin Routing [5] 0.7V [3] 0V (Gnd) E Gnd[1] 0V [6] 4.1V [4] 0V (Gnd) Q8000 RL_ON (PWR_On)[2] 0V [7] 4.5V [5] 3.37V Pin 1st Driver Q8308 CEC Remote[3] 0V [8] 4 5V (In) [6] 3 37V B 0 66V Pin HDMI CEC[3] 0V [8] 4.5V (In) [6] 3.37V B 0.66V Pin HDMI CEC[4] 0V [7] 3.34V C 0V [B] 2.72V[5] 0V IC9000 Serial Flash [8] 3.37V (In) E Gnd [G] 2.73V[6] (-5.47V) Pin T-CON [S] 3.27V[7] n/c (5.59V) [1] 0.06V Q8002 PWR_ON [D] 3.37V [8] n/c (0V) [2] 0.67V D8306, 7, 9 5V Pull Up Routing Pin Switch[9] n/c (3.3V) [3] 3.3V (In) Pin HDMI SCL/SDA [1] 3.36V (In) Q8701 IR Wireless Pass

[10] n/c (0.2V) [4] 0V (Gnd) A1 5.04V [2] 0V Pin 2nd Driver[11] n/c (3.3V) [5] 0V C 4.58V [3] 3.3V (Out) G 24.5V (2.3V Dongle I[12] 3.35V [6] 0.34V A2 0V S 24V[13] 0V [7] 3.31V (In) D 0V (24.5V Dongle In)[14] (-5.47V) [8] 3.34V (In) D8312 3.5V Pull Up[15] 0V (Gnd) Pin HDMI CEC[16] 3.37V A1 0V

C 3.26VA2 3.2V


Main Board X9001 and X9000 Crystal ChecksMain Board X9001 and X9000 Crystal Checks

X9001 IC9001 T-CON Crystal X9000IC9301 TruMotion / Di i C t l1.58V

3.19V p/p

IC9001 T CON Crystal

1.56V2.54V p/pDimming Crystal

1.6V4.86V p/p

1.6V3 27V p/p

Runs when set is On

25Mhz

3.27V p/p12Mhz

Runs when set is On

X9001

X9000

MAIN Board


Main Board X8100 , X8101 and X1001 Crystal ChecksMain Board X8100 , X8101 and X1001 Crystal Checks

X8100 IC900 BCM Crystal X1001IC8100 Micro Crystal

1.95V3.13V p/p

1.52V781mV p/pEither leg Either leg

1.522.26V p/p

1.3V789mV p/p10Mhz 54MhzEither leg

Runs allThe time

Runs when set is On

MAIN BoardX8100

1.85V p/p 2.82V p/pX8100

X1001X8101

1.75V1.5V Runs allThe time


The time

X8101

Main Board DC to DC Converter (Voltages for Panel) ChecksMain Board DC to DC Converter (Voltages for Panel) Checks

Location: Top Center of Board

+7.81VHVDD

IC9102

L9100

+16V

IC9102

L9104

Panel 12V

D9101

16VVDD B+ for

IC9102IC9103

L9102

+27VVGH

D9101

Panel 12V

IC9103

-5VVGL

+3.3VVCC

L9101


D9102

Main Board Additional Panel Voltage ChecksMain Board Additional Panel Voltage Checks

Location: Top Left of Board

P7500P7501

IC9101IC9101Back Side of Board

-4.8V (VDD-ODD)

From IC9101 Pin 21

From IC9101 Pin 19

-4.7V (VST)

From IC9101 Pin 20

From IC9101 Pin 19


-4.8V (VDD-EVEN)

Main Board Connector P8000 to Power Supply Voltage and Diode CheckMain Board Connector P8000 to Power Supply Voltage and Diode Check

P8000 Main Board" to P201 SMPS"P8000Pin Label STBY Run Diode Check

1 PWR-ON 0V 3.36V Open

2-4 20V 0V 21.27V Open

5-8 Gnd Gnd Gnd Gnd

Odd Pins Front Row 9-12 3.5V 3.57V 3.5V 1.24V13-15 Gnd Gnd Gnd Gnd

16 V-SYNC 0V 0.02V 1.06V

17 12V 0V 11 43V ODiode Mode values taken with all Connectors Removed

17 12V 0V 11.43V Open

18 INV-ON 0V 3.28V 1.62V

19 12V 0V 11.43V Open

20 SCLK 0V 0.09V 1.06V

21 12V 0V 11.43V Open


23 L-DIM (SIN) 0V 3.3V 1.05V

24 ERROR Gnd Gnd Gnd

(1) PDIM Pin 22 can vary according to incoming video IRE level, OSD Backlight setting and Intelligent Sensor (room light condition). R 0 37V t 3 3V

24 ERROR Gnd Gnd Gnd

P-DIM13.66V p/p 50IRE


Range 0.37V to 3.3V.

Main Board Connector P7500 to the Panel Voltage and Diode CheckMain Board Connector P7500 to the Panel Voltage and Diode CheckThere are no Stand-By Voltages for the ConnectorDiode Mode values taken with all Connectors RemovedP7500 Connector Main" to the Panel

Pin Label Run Diode Check

1 Gnd Gnd Gnd

2 GMA1 14.91V Open

3 GMA3 13 5V Open


21 LV0+ 1.06V 0.9V

22 LV0- 1.27V 1.09V

23 LV1+ 1 4V 0 9V


41 VDD 15.57V Open

42 VDD 15.57V Open

43 Gnd Gnd Gnd3 GMA3 13.5V Open

4 GMA4 12.78V Open

5 GMA6 11.88V Open

6 GMA7 10.02V Open

7 GMA9 8 02V Open

23 LV1+ 1.4V 0.9V

24 LV1- 1.3V 1.09V

25 LV2+ 1.03V 0.9V

26 LV2- 1.3V 1.09V

27 LVCLK+ 1 16V 0 9V

43 Gnd Gnd Gnd

44 VCOM_IN 6.86V Open

45 VCOM_FB 6.87V Open

46 Gnd Gnd Gnd

47 VST ( 4 7V) 1 5V7 GMA9 8.02V Open

8 GMA10 7.48V Open

9 GMA12 5.99V Open

10 GMA13 4.08V Open

11 GMA15 2 98V Open

27 LVCLK+ 1.16V 0.9V

28 LVCLK- 1.17V 1.09V

29 LV3+ 1.07V 0.9V

30 LV3- 1.27V 1.09V

31 LV4+ 1 02V 0 9V

47 VST (-4.7V) 1.5V

48 VGL (-5V) 0.6V

49 VDD_EVEN (-4.8V) 1.5V

50 VDD_ODD (-4.8V) 1.5V

51 VGI P (VGL) ( 5V) 0 6V11 GMA15 2.98V Open

12 GMA16 2.35V Open

13 GMA18 1.06V Open

14 Gnd Gnd Gnd

15 OPT N 1 06V 2 06V

31 LV4+ 1.02V 0.9V

32 LV4- 1.3V 1.09V

33 LV5+ 1.02V 0.9V

34 LV5- 1.3V 1.09V

35 Gnd Gnd Gnd

51 VGI_P (VGL) (-5V) 0.6V

52 VGI_N (VGH) 27.4V Open

53 CLK6 8V 1.5V

54 CLK5 8V 1.5V

55 CLK4 8V 1 5V15 OPT_N 1.06V 2.06V

16 H_CONV 1.07V Gnd

17 VST_IN 0V 1.06V

18 POL 0.62V 1.06V

19 SOE 0 3V 1 06V

35 Gnd Gnd Gnd

36 VCC 3.3V 1.64V

37 VCC 3.3V 1.64V

38 Gnd Gnd Gnd

39 HVDD 7 81V Open

55 CLK4 8V 1.5V

56 CLK3 8V 1.5V

57 CLK2 8V 1.5V

58 CLK1 8V 1.5V

59 Z OUT 7 7V Open


19 SOE 0.3V 1.06V

20 Gnd Gnd Gnd

39 HVDD 7.81V Open

40 HVDD 7.81V Open

59 Z_OUT 7.7V Open

60 Gnd Gnd Gnd

Main Board Connector P7501 to the Panel Voltage and Diode CheckMain Board Connector P7501 to the Panel Voltage and Diode CheckThere are no Stand-By Voltages for the ConnectorDiode Mode values taken with all Connectors RemovedP7501 Connector Main" to the Panel


1 Gnd Gnd Gnd

2 Z_OUT 7.7V Open

3 CLK1 8V 1 5V


21 HVDD 7.81V Open

22 HVDD 7.81V Open

23 Gnd Gnd Gnd


41 Gnd Gnd Gnd

42 SOE 0.3V 1.06V

43 POL 0 62V 1 06V3 CLK1 8V 1.5V

4 CLK2 8V 1.5V

5 CLK3 8V 1.5V

6 CLK4 8V 1.5V

7 CLK5 8V 1 5V

23 Gnd Gnd Gnd

24 VCC 3.3V 1.64V

25 VCC 3.3V 1.64V

26 Gnd Gnd Gnd

27 RV0+ 1 07V 1 09V

43 POL 0.62V 1.06V

44 VST_IN 0V 1.06V

45 H_CONV 1.07V Gnd

46 OPT_N 1.06V 2.06V

47 Gnd Gnd Gnd7 CLK5 8V 1.5V

8 CLK6 8V 1.5V

9 VGH 27.4V Open

10 VGH (-5V) 0.6V

11 VGH ODD (-4 8V) 1 5V

27 RV0+ 1.07V 1.09V

28 RV0- 1.12V 0.9V

29 RV1+ 1.13V 1.09V

30 RV1- 1.23V 0.9V

31 RV2+ 1 13V 1 09V

47 Gnd Gnd Gnd

48 GMA18 1.06V Open

49 GMA16 2.35V Open

50 GMA15 2.98V Open

51 GMA13 4 08V Open11 VGH_ODD (-4.8V) 1.5V

12 VGH_EVEN (-4.8V) 1.5V

13 VGL (-5V) 0.6V

14 VST (-4.7V) 1.5V

15 Gnd Gnd Gnd

31 RV2+ 1.13V 1.09V

32 RV2- 1.22V 0.9V

33 RVCLK+ 1.17V 1.09V

34 RVCLK- 1.18V 0.9V

35 RV3+ 1 08V 1 09V

51 GMA13 4.08V Open

52 GMA12 5.99V Open

53 GMA10 7.48V Open

54 GMA9 8.02V Open

55 GMA7 10 02V Open15 Gnd Gnd Gnd

16 VCOM_FB 6.87V Open

17 VCOM_IN 6.86V Open

18 Gnd Gnd Gnd

19 VDD 15 57V Open

35 RV3+ 1.08V 1.09V

36 RV3- 1.27V 0.9V

37 RV4+ 1.12V 1.09V

38 RV4- 1.22V 0.9V

39 RV5+ 1 13V 1 09V

55 GMA7 10.02V Open

56 GMA6 11.88V Open

57 GMA4 12.79V Open

58 GMA3 13.5V Open

59 GMA1 14 91V Open


19 VDD 15.57V Open

20 VDD 15.57V Open

39 RV5+ 1.13V 1.09V

40 RV5- 1.22V 0.9V

59 GMA1 14.91V Open

60 Gnd Gnd Gnd

Main Board P8200 to (Ft. IR/Intelligent Sensor) Voltage and Diode CheckMain Board P8200 to (Ft. IR/Intelligent Sensor) Voltage and Diode Check

P8200 Connector "MAIN Board" To P100 "IR Board" P8200 1

Pin Label STBY Run Diode Check1 (1) SCL 3.56V 3.5V Open2 (1) SDA 3.56V 3.5V Open3 Gnd Gnd Gnd Gnd4 KEY 1 3.32V 3.3V 1.9V5 KEY 2 3.29V 3.3V 1.9V6 3.5V_ST 3.56V 3.47V 1.24V7 Gnd Gnd Gnd Gnd8 LED_LOGO 0V 0V Open9 (2) IR 1 63V 1 6V O9 (2) IR 1.63V 1.6V Open

10 Gnd Gnd Gnd Gnd11 +3.3V_Normal 0V 3.34V 0.52V12 LED R/BUZZ 0V 0V Open12 LED_R/BUZZ 0V 0V Open

(1) Clock pulses only present when Intelligent Sensor is turned on. (3.7V p/p)(2) IR pulses (1.6V p/p)



Main Board Connector P8800 to Speakers Voltage and Diode CheckMain Board Connector P8800 to Speakers Voltage and Diode CheckQ8800

Amp MuteQ8800 (Mute) Active Low. Normal 3.3V Collector to Pin 25

IC8800Amp 1.8V

P8800 CONNECTOR "Main" to "Speakers"

Use speaker out to test for defective Audio Amp IC8801Note: (Normal, Audio B+) Mute

Pin 25

Pin LABEL SBY Run Diode Check1 SPK-R(-) 0V 10.62V Open2 SPK-R(+) 0V 10.62V Open3 SPK L( ) 0V 10 62V O

Audio B+21 3V

IC8801

3 SPK-L(-) 0V 10.62V Open4 SPK-L(+) 0V 10.62V Open

21.3VPins 49-52

(1)(1)


Diode Mode values taken with all Connectors RemovedP8800

Main JK8700 Wireless Media Box Dongle Jack (Voltage and Diode Check)Main JK8700 Wireless Media Box Dongle Jack (Voltage and Diode Check)


JK8700 "MAIN Board" To "Wireless Media Box Dongle"

Wireless Media Box DonglePin Label STBY Run Diode Check1-6 *20.3V 0V 20.3V 0.98V

7 Detect 0V 0.3V 0.98V

8 Interrupt 0V 3.3V 1.2V JK8700J k

Wireless Media Box Dongle must be plugged in for

these voltages.

9 Gnd 0V Gnd Gnd

10 n/c 0V 3.3V 1.1V

11 Gnd 0V Gnd Gnd

12 I2C_SCL 0V 3.3V 1.02V

Jack

_

13 I2C_SDA 0V 3.3V 1.02V

14 Gnd 0V Gnd Gnd

15 Wireless_RX 0V 3.3V 1.17V

16 Wi l TX 0V 3 3V 1 22V

1

Diode Mode values taken with all Connectors

Removed

16 Wireless_TX 0V 3.3V 1.22V

17 Gnd 0V Gnd Gnd

18 IR 0.67V 3.3V 1.37V

19-20 Gnd 0V Gnd Gnd

Voltages with Wireless Media Box Dongle plugged in. Use Media Box Dongle side to read voltages. Remove cover, (see Wireless Media Box training manual for details).

*20.3V Switched from Q8701 Drain Back side of the board.Q8701 turned on by Q8700 front side of the board.


Q8700 turned on by Microprocessor pin 38.

FRONT (IR, INTELLIGENT SENSOR and MOVING LED) SECTIONFRONT (IR, INTELLIGENT SENSOR and MOVING LED) SECTION

The Intelligent Sensor and IR board (located on the bottom left as viewed from the rear) contains the IR (Infrared Remote Sensor) and the Intelligent Sensor. This board also connects with the Soft Touch Key Board and the Center LG Logo board. The Center LG Logo lights after power on and the picture appears. Then dims down in about 2 seconds. At power off, it does the reverse.

The IR board receives it operating B+ via CON1 pin 6 (STBY 3.5V).

The IR (Infrared) remote receiver can be measured (1.57V) at pin 9 of connector CON1 or P8200 on the Main board in Stand-By. During run pin 9 reads (1.54V).

The IR pulses (1.6V p/p) CON1 pin 9 are sent to P8200 on the Main board and on to theThe IR pulses (1.6V p/p) CON1 pin 9 are sent to P8200 on the Main board and on to the Microprocessor (IC8101) via pin 16.

The Intelligent Sensor communicates with the Micro/Video Processor IC900 BCM Chip via clock and data lines SCL1 and SDA1 arriving on connector CON1 from P8200 pins 1 and 2 on the Main board.

The Front Power LEDs are controlled by these same Clock and Data lines which communicate with the LED Driver IC U1 on the Soft Touch Key board.

The Key board is routed to the IR board via CON2 and output on CON1 Key 1 and Key 2 lines, y p y y ,(Key 1 pin 4 and Key 2 pin 5). Arriving at P8200 pins 4 and 5 on the Main Board. Then to the Microprocessor 25 and 26 lines.


Front IR Board (Connections Identified)Front IR Board (Connections Identified)p/n EBR64966201

J2J2To Soft Touch

Key Board(1)

J3 To Center

Logo BoardLogo Board

J1To Main BoardIR and Intelligent

Sensor board


Front Board Connectors CON1, CON2 and CON3 Voltage and Diode CheckFront Board Connectors CON1, CON2 and CON3 Voltage and Diode Check

J1 "Front IR" to P8200 " MAIN"J2 "Front IR" to Soft Touch Key Board"

Pin Label STBY Run Diode Check1 (1) SCL 3.56V 3.5V Open2 (1) SDA 3.56V 3.5V Open

Pin STBY Run Diode Check1 3.56V 3.47V Open2 0V 1.63V Open

J2 Front IR to Soft Touch Key Board

p

3 Gnd Gnd Gnd Gnd4 KEY 1 3.32V 3.3V 1.9V5 KEY 2 3.29V 3.3V 1.9V

2 0V 1.63V Open3 Gnd Gnd Gnd4 3.56V 3.5V Open5 3.56V 3.5V Open

6 3.5V_ST 3.56V 3.47V 1.24V7 Gnd Gnd Gnd Gnd8 LED_LOGO 0V 0V Open

6 Gnd Gnd Gnd7 3.32V 3.3V 1.9V8 3.29V 3.3V 1.9V

9 (2) IR 1.63V 1.6V Open10 Gnd Gnd Gnd Gnd11 +3.3V_Normal 0V 3.34V 0.52V12 LED R/BUZZ 0V 0V O

Pin STBY Run Diode Check

J3 "Front IR" to LG Logo Board"

12 LED_R/BUZZ 0V 0V Open 1 3.56V 3.47V 1.24V2 Gnd Gnd Gnd3 1.36V 0.6V Open4 G d G d G d

(1) Clock pulses only present when Intelligent Sensor is turned on. (3.7V p/p)

(2) IR pulses (1.6V p/p)


Diode Mode values taken with all Connectors Removed 4 Gnd Gnd Gnd

INVISIBLE SPEAKER SECTIONINVISIBLE SPEAKER SECTION

The 42LE5500 contains the Invisible Speaker system. The Full Range Speakers point downward, so there is no front viewable speaker grill or air ports.

Speakerp/n EAB60961501

g p p , p g p

Installed

Top View

Side View

Front View


INTERCONNECT DIAGRAM (11 X 17 FOLDOUT SECTION)INTERCONNECT DIAGRAM (11 X 17 FOLDOUT SECTION)

This section shows the 11X17 foldouts. Use these pages as a single sheet Quick Reference page when working on this set. It list connectors and their voltages Also tricks and tips for easier troubleshootingtheir voltages. Also tricks and tips for easier troubleshooting.

The Adobe version of this Training Manual allows the viewer to zoom in and out making reading of the small text easier.

If ibl h i ti i t th f ll i I t t Di iIf possible, when printing, print the following Interconnect Diagram using 11X17 paper for easier viewing.


Q?

D

G S

A-CA

C


P8200


LGE3549XQ

P8800

Q8200

Q8201

Q8700

IC8300

L8805L8804

HDMISelectIC8801

IC8800

IC9004Q8800

Micro

IC8101

SW1000

SW8100X8100

P90

00n/

c

X900012Mhz

IC1000IC901

IC9001T-CON

LGE7378A

X930025Mhz

IC9300

SW9300

P7501 P7500 IC9100L9100

IC9102

L9102

L9101

IC9103

A-CA

C

D9101

D9102IC9302

L9301

IC8901IC8900 L8904

3

2 1

3

2 1

Q8004Q8005

Q8001

Q8003

IC8008

IC8007

L8905IC8903IC8902

L8012IC8002 IC8001

IC8003

L8015

IC8005P8000

L8010L8009

P9000Gamma

IC605IC603IC301

IC302

L8004 USB1

54MHz X1001

USB2

IC700

IC300Q300

TU700TDVJ-H031F


8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V

2. NC 1. NC

HP

HDMI

D8310

ComponentComposite

IC8000

Digital Video

Analog

Tuner B+


Audio

A2 A1

C

LAN

X810132.768Khz

IC9301LG5111

42LE5500 INTERCONNECT DIAGRAM

Intelligent SensorIntelligent Sensor

Stand-by

P8200 "MAIN Board" To J1 "IR Board"

Indicates Hot Ground

SMPS TEST 1

P201

A

PWR

ON

3 17 511 915 1319 17214 28 612 1016 1420 1822

2324

STBY 3.5V

12V12V

STBY 3.5V 20V20V

20V12V

INV-O

N B

SMPS TEST 2

P201

A

PWR

ON

3 17 511 915 1319 17214 28 612 1016 1420 1822

2324

STBY 3.5V

12V12V

STBY 3.5V 20V20V

20V12V

Front pins on connectorare odd numbers.

Front pins on connectorare odd numbers.

To the Panel

Diode Check

9 IR 1.63V Open10 Gnd Gnd Gnd11 3.3V_Normal 0V 0.59V12 LED_BUZZ 0V Open

Pin Label STBY Run

1.6VGnd

3.34V0V

7 Gnd Gnd Gnd Gnd8 LED_LOGO 0V 0V Open

Pin Label STBY Run 1 SCL 3.56V 3.5V Open2 SDA 3.56V 3.5V Open3 Gnd Gnd Gnd Gnd4 Key1 3.32V 3.3V 1.9V5 Key2 3.29V 3.3V 1.9V6 3.5V_ST 3.56V 3.47V 1.24V

Diode Check

P8800 "Main" To "Speakers"Pin SBY Run Diode1 SPK-R(-) 0V 12.3V Open2 SPK-R(+) 0V 12.3V Open3 SPK-L(-) 0V 12.3V Open4 SPK-L(+) 0V 12.3V Open

Label

(1) PDIM Pin 22 can vary according to incoming video IRE level, OSD Backlight setting and then Intelligent Sensor (room light condition) Output from the Video Processor IC900. Range 0.37V to 3.3V.

Front IRIR ReceiverIntelligent

SensorJ1

Front Soft Switch Keys

J3J2

LG Logo

80 IRE32V p/p 120Hz

Note: If a particular area is exhibiting a dimmer backlight level than other areas or the overall brightness seems dim, be sure to first check the customers Menu setting for Backlights. Raise the percentage and see if the overall brightness returns to normal. If not, 1st: Check the P-DIM level, it should rise with the percentage shown on screen. 100%, 3.3V. Follow the P-DIM signal all the way to the Inverter. 2nd: Turn off Local Dimming in the Customers Menu. If the brightness returns to normal, examine the signals required for Local Dimming. (SIN, V-SYNC and SCLK).

Drive Signalsto LED Blocks

5 IRE32V p/p 120Hz

The Panel contains 12 LED Blocks To force a Block to turn on, simple ground the pin providing the 13V source is present.

SMPS TEST 1: To Force Power Supply On.Disconnect P8000 on Main board.(A) Jump pins 9, 10, 11 or 12 (3.5V) to pin 1. (Test Voltage Outputs 12V, 20V to Main and 120V to the Inverter). Remove AC power. Leave the jumper in place.

SMPS TEST 2: (B) Jump pins 9, 10, 11 or 12 (3.5V) to pin 18 (INV-ON). Apply AC power, the Backlights should turn on.

Note; If there is a problem with a load on the Inverter you canRemove AC and Disconnect P205 or P204. When AC is reapplied, the Backlight LEDs should turn on for about 4 seconds and then shut off.

J2 "IR Board" To "Soft Touch Key Board"Pin STBY Run Diode1 3.45V 3.36V Open2 0V 1.63V Open3 Gnd Gnd Gnd4 3.3V 3.3V Open

5 3.28V 3.28V Open6 Gnd Gnd Gnd7 3.45V 3.36V Open8 3.45V 3.36V Open

Pin STBY Run Diode

1 3.45V 3.0V 1.5V2 Gnd Gnd Gnd3 1.36V 0.64V Open4

Pin STBY Run Diode

J3 "IR Board" To "Center Logo Board"

Gnd Gnd Gnd

SW8100Micro Reset

SW1000Video Reset

SW9300Tru-

Motion Reset

SMPS BOARDp/n: EAY60803101

SK101AC In

21uF

/450

V21

uF/4

50V

21uF

/450

V21

uF/4

50V

21uF

/450

V

16uF/450V

21uF/450V

16uF/450V

+

-

BD101

-

+

D206

IC501

IC502

IC503

Q511

F102 F1005A

250V

1A250V

F1031A

250V

F101

3.15A250V

D601 Q602

L601 L602

D201

D202

D203

D204

P201

P205

P204

R149

RL101

RL102

Q602

IC104IC105

Q207 Inverter

Q203

T102

D601

R149

T501

T101

C EB

CEB

CEB

CE B

Components Inside

Dashed Lineare Hot Ground

F101-F103 Hot GndStby 7.6VRun 396V

120V

LED Power

To the Panel

SCLK Pin 20 P2013.76V p/p

V-SYNC Pin 16 P2013.64V p/p

S-CLK Pin 23 P2013.25V p/p

Local Dimming On

S-CLK Pin 23 P2013.25V p/p

Local Dimming Off

P8000P201 "SMPS" To P8000 "MAIN Board"

Diode

Open

Gnd

1.05V

Open

Open

1.06V

Open

1.62V

Open

1.06V

Gnd

1.24V

Open

Open

Pin Label STBY Run Diode Check24 ERROR 0V 0V 1.45V

23 L-DIM (SIN) 0V 3.3V Open


21 12V 0V 11.43V 0.178V

20 SCLK 0V 0.09V Open

19 12V 0V 11.43V 0.178V

18 INV-ON 0V 3.28V Open

17 12V 0V 11.43V 0.178V

16 V-SYNC 0V 0.02V Open


9-12 3.5V 3.57V 3.5V Open

5-8 Gnd Gnd Gnd Gnd

2-4 20V 0V 21.27V 1.10V

1 PWR-ON 0V 3.36V 1.02V

Pin Label STBY Run Diode Check12 02.A 0V 117.8V Open

11 n/c n/c n/c Open

10 02-1C 0V 1V~30V Open

9 02-2C 0V 1V~30V Open

8 02-3C 0V 1V~30V Open


5 01-3C 0V 1V~30V Open

4 01-2C 0V 1V~30V Open

3 02-1C 0V 1V~30V Open

2 n/c n/c 0V Open

1 01.A 0V 117.8V Open

P204 "SMPS" To The Panel"

Pin Label STBY Run Diode Check12 04.A 0V 120V Open

11 n/c n/c n/c Open

10 04-1C 0V 1V~30V Open

9 04-2C 0V 1V~30V Open

8 04-3C 0V 1V~30V Open


5 03-3C 0V 1V~30V Open

4 03-2C 0V 1V~30V Open

3 03-1C 0V 1V~30V Open

2 n/c n/c 0V Open

1 03.A 0V 120V Open

P205 "SMPS" To The Panel"

Q901

IC602IC606IC604

Q702Q701

IC8200

IC8401

IC8400Q8304

Q8301

D8307 Q8303Q8300

Q8701IC8700

Q8205Q8203

Q8305Q8302

D8306

DSG

Q200

G

S

B

D

Q8308

D8312

IC8100

IC9000

IC9303IC9101

Q8000 Q80021

2

3

D8309

E

B

C

E

B

C

E

B

C

E

B

C

E

B

C

E

B

C

E

B

C

E

B

C

E

BC

E

BC

E

BC

E

B

C

P204

P205

These drivers ground the LED blocks. (12 Total). If the 120V is present on Pins 1 and 12 of P204 and P205 you can ground these test points to turn on a block.

1V (100 IRE)30V (0 IRE)Gnd

Gnd

120V

120V

120V

120V

n/c

n/c

n/c

n/c

n/c

n/c

*1V~30V LED Drive

*1V~30V LED Drive

*1V~30V LED Drive

*1V~30V LED Drive

*White 100 IRE to Black 0 IRE

INVERTER SECTIONOF THE SMPS

To Speakers

See the Inverter Section Blow Up on the Right

To The Panel

Forcing onA Block of LEDs.

1 VDD-33 3.5V2 VLED-RANGE 0V3 Gnd Gnd4 +12VS 12.44VPin 17-19-21 P2015 Gnd Gnd6 +3.5VS 3.57VPin 9-12 P201

1 INV_ON 3.28VPin 18 P2012 Gnd Gnd3 Gnd Gnd4 SCLK 0.09VPin 20 P2015 FB_STR_VF 1V6 P-DM1 1.9VPin 22 P201

1 Error 0VPin 24 P2012 (L-DIM) SIN 3.3VPin 23 P2013 POWER_ON 3.35VPin 1 P2014 VSYNC_IN 0VPin 16 P2015 Gnd Gnd6 Gnd Gnd

You can also these each of the 12 blocks functionality by grounding the driver output signals. See Forcing on a Block of LEDs on the right.

42LE5500 MAIN (FRONT SIDE) SIMICONDUCTORS

IC700 (+1.26V_TU) IC8002 (D1.8V) IC8005 (+3.3V_NORMAL) IC8902 (+1.26V_MEMC) IC9102 DC to DC Q8003 PANEL_VCC Q8700 Wireless PWRPin Regulator Pin Regulator Pin Regulator Pin Regulator Pin HVDD T-CON Pin Control 2nd Driver Dongle Out Turns on Q8701[1] 0V (Gnd) [1] 5V [1] 0V (Gnd) [1] 0V (Gnd) [1] 0V (Gnd) B 0.679V B 0.66V[2] 1.26V (Out) [2] 3.34V (In) [2] 11.8V (In) [2] 11.8V (In) [2] 11.72V (In) C 0V C 0.14V[3] 3.3V (In) [3] 1.8V (Out) [3] 0V (Gnd) [3] 0V (Gnd) [3] 11.72V (In) E Gnd E Gnd

[4] Gnd [4] 0.8V [4] 0.8V [4] 3.25VIC1000 SOC Reset [5] Gnd [5] 0.86V [5] 0.7V [5] 3.2V Q8004 PANEL_VCC Q8700 Wireless PWR

Pin Generator [6] 0.9V [6] 3.36V (PWR On/Off2 Ctl) [6] 3.36V (PWR On/Off2 Ctl) [6] 0V Pin Switch Dongle In Turns on Q8701[1] 3.32V (In) [7] 0.9V [7] 3.36V (Out) [7] 1.3V (Out) [7] 0V S 11.8V (In) B 0.0V[2] 0V (Gnd) [8] 1V [8] 3.36V (Out) [8] 1.3V (Out) [8] 11.7V G 1.8V (Enable) C 24V[3] 3.3V (Out) [9] 2.38V [9] 0V (Gnd) D 11.8V (Out) E Gnd

[10] 3.36V (PWR On/Off1 Ctl) IC8007 Power Det Gen IC8903 (+3.3V_MEMC) [10] 1.13VIC8000 5V Regulator Pin (+12V and +3.5V) Pin Regulator [11] 0V (Gnd) Q8005 INV_ON Q8800 AMP_MUTE

Pin for USB IC8003 (+5V_NORMAL) [1] 0V (Gnd) [1] 0V (Gnd) [12] 0V (Gnd) Pin Driver Pin Pin 25 IC8801[1] 11.79V (In) Pin Regulator [2] 3.6V (In) [2] 11.8V (In) [13] 0V (Gnd) B 0V (INV ON) En B 0V[2] 5V (Out) [1] 0V (Gnd) [3] 3.5V (Out) [3] 0V (Gnd) [14] 7.7V C 3.1V (Out) C 3.336V[3] 5V (Out) [2] 11.8V (In) [4] 0.8V [15] 7.7V (HVDD) E Gnd E Gnd[4] 10.5V [3] 0V (Gnd) IC8008 Power Det Gen [5] 0.8V [16] 0V (Gnd)[5] 3.3V [4] 0.8V Pin (+24V) [6] 3.36V (PWR On/Off2 Ctl) Q8200 IR Buffer D9101 VGH/VDD[6] 0.8V [5] 0.86V [1] 0V (Gnd) [7] 3.3V (Out) IC9300 Reset for Pin 2nd Pin Rectifyer[7] 4.99V [6] 3.37V (PWR On/Off2 Ctl) [2] 3.6V (In) [8] 3.3V (Out) Pin LG5111 B 0.02V A 15.4V

[8] 0V (Gnd) [7] 5V (In) [3] 3.7V (Out) [1] 3.32V (In) C 3.4V AC 22.2V [8] 5V (In) IC9100 P-GAMMA [2] 0V (Gnd) E Gnd C 27.4V (VGH)

IC8001 D1.2V and A1.2V IC8800 (+1.8V_AMP) Pin Chip [3] 3.34V (Out)Pin Regulator IC8004 A2.5V Regulator Pin Regulator [1] 3.3V Q8201 IR Buffer D9102 VGL/VCC[1] 0V (Gnd) Pin for USB [1] 0V (Gnd) [2] 0V (Gnd) IC9302 (1.8V_L/Dimming) Pin 1st Pin Rectifyer[2] 3.3V [1] n/c [2] 1.8V (Out) [3] 3.3V (In) Pin Regulator B 0V A (-5V VGL)[3] 0V (Gnd) [2] 3.26V (In) [3] 3.295V (In) [4] 0V (Gnd) [1] 0V (Gnd) C 3.3V AC (-1.9V)[4] 1.2V [3] 3.26V (In) [5] 6.8V [2] 11.8V (In) E Gnd C 0V[5] 3.3V [4] n/c IC8901 (+1.5V_MEMC) [6] 6.8V [3] 0V (Gnd)[6] n/c [5] n/c Pin Regulator [7] 15.3V [4] 0.8V Q8306 HDMI [7] 4.46V [6] 2.55V (Out) [1] 0V (Gnd) [8] 15.3V [5] 0.76V Pin Det

[8] 3.3V [7] 0.8V [2] 1.5V (Out) [9] n/c [6] 3.34V (PWR On/Off2 Ctl) B 0V[9] 3.3V [8] 0V (Gnd) [3] 3.3V (In) [10] 13.47V [7] 1.8V (In) C 3.3V

[10] 3.3V [11] 12.75V [8] 1.8V (In) E Gnd[11] 1.2V [12] 11.8V[12] Gnd [13] 10V Q8001 PANEL_VCC Q8307 HDMI [13] 3.3V [14] 5.96V Pin Control 1st Driver Pin Det[14] 0.8V [15] 4.06V B 0V B 0V

[16] 15.3V C 0.68V C 4.18V[17] 0V E Gnd E Gnd[18] 2.96V[19] 2.33V[20] 3.3V (In)

42LE5500 MAIN (BACK SIDE) SIMICONDUCTORS

IC602 D1.8V IC8200 RS232 IC8401 EDID Data IC9303 EEPROM Q8000 RL_ON (PWR_On) Q8303, 4, 5 HDMI 3Pin Regulator Pin Routing Pin PC Pin for LG5111 Pin 1st Driver Pin Det[1] 0V (Gnd) [1] 0V [1] 0V (Gnd) [1] 0V (Gnd) B 0.66V B 0V[2] 3.29V (PWR On/Off1 Ctl) [2] 0V [2] 0V (Gnd) [2] 0V (Gnd) C 0V C 4.2V[3] 0.9V (DDR_VTT) [3] 0V [3] 0V (Gnd) [3] 0V (Gnd) E Gnd E Gnd[4] 0.93V [4] 0V [4] 0V (Gnd) [4] 0V (Gnd)[5] 1.83V [5] 0V [5] 0.7V [5] 3.37V Q8002 PWR_ON Q8308 CEC Remote[6] 3.38V (In) [6] (-5.47V) [6] 4.1V [6] 3.37V Pin Switch Pin HDMI CEC[7] 1.8V (Out) [7] n/c (5.59V) [7] 4.5V [7] 3.34V [1] 3.36V (In) [B] 2.72V[8] 0.91V (DDR_VTT) [8] n/c (0V) [8] 4.5V (In) [8] 3.37V (In) [2] 0V [G] 2.73V

[9] n/c (3.3V) [3] 3.3V (Out) [S] 3.27VIC8100 EEPROM [10] n/c (0.2V) IC8700 Wireless Q200 (1.8V_HDMI) [D] 3.

Documents

9619_LG_42LE5500_42LE5500-UA_Chassis_LA02E_Televisor_LED-LCD_Manual_de_entrenamiento+diagramas.pdf