INSTALLATION INSTRUCTIONS FOR PART 99-7011

99-7011

MITSUBISHI Lancer 2008-2009

KIT FEATURES

• DIN Radio Provision with Pocket• ISO Mount Radio Provision with Pocket• Double DIN Radio Provision• Stacked ISO Mount Units Provision

• A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Snap in Pocket

KIT COMPONENTS

A

Phillips Screwdriver/ Panel Removal Tool • Cutting Tool

1-800-221-0932 www.metraonline.com

B

D EC

FTOOLS REQUIRED:

APPLICATIONS

© COPYRIGHT 2008-2009 METRA ELECTRONICS CORPORATION

WIRING AND ANTENNA CONNECTIONS: (Sold Separately)Harness:• MITO-02 - Mitsubishi Rockford interface • 70-7005 - Mitsubishi harness 2007-up Antenna Adapter:• No antenna adapter required

Dash Disassembly- Mitsubishi Lancer 2008-2009 . . . . . . . . . . . . . . . . . . . . . . . . 1,2

Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Kit Assembly- DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4- ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5- Double DIN Radio Provision/Stacked ISO Mount Units Provision . . . . . . 6

Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

TABLE OF CONTENTS

99-7011

Note: Refer also to the instructions included with the aftermarket radio.

KNOWLEDGE IS POWEREnhance your installation and fabrication skills byenrolling in the most recognized and respectedmobile electronics school in our industry.Log onto www.installerinstitute.com or call800-354-6782 for more information and take steps toward a better tomorrow.

1

3

MITSUBISHI LANCER 2008-2009

99-7011 DASH DISASSEMBLY

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Open the glove box and remove (1)Phillips screw from the panel to theright of the glove box door. Unclipand remove the panel. (Figure A)

Remove (1) Phillips screw from thepanel above the glove box thenunclip and remove the panel. (Figure B)

Continued on page 2.

2

B

A

2

MITSUBISHI LANCER 2008-2009

99-7011 DASH DISASSEMBLY

4 Unclip the radio switch panel includ-ing the hazard switch assembly.Unplug hazard switch assembly andremove panel. (Figure C)

5 Remove (4) Phillips screws secur-ing the radio chassis. Unplug andremove chassis.

7 Unclip assembly, unplug ribboncable from assembly and removeassembly from the factory radiopanel. Retain screws and hazardswitch assembly for re-use duringkit preparation.

6 Remove (3) Phillips screws securingthe hazard switch assembly to thefactory radio switch panel. Unclipand remove the switch. (Figure D)

8 Unclip and remove the a/c ventsfrom the factory radio switch panel.(Retain a/c vents for re-use duringkit preparation)

9 Remove and retain (7) factory clipsfrom rear of radio housing for re-use during kit preparation.

Continue to kit preparation.

PASSENGERAIRBAG OFF PASSENGER

PASSENGERAIRBAG OFF PASSENGER

D

C

3

99-7011 KIT PREPARATION

Secure the hazard switch assembly into the radio housing using the factory hard-ware. Snap the a/c vents into the radio housing. (Figure A)

Use the (7) plastic factory clips previously removed during dash disassembly andattach where shown. (Figure B)

1

2

PASSENGER

PASSENGER

AIRBAGOFF

A

REAR VIEW OF RADIO HOUSING

B

MITSUBISHI LANCER 2008-2009

Continue to kit assembly

99-7011 KIT ASSEMBLY

4

A

B

C

DIN RADIO PROVISION WITH POCKET

Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs outward. (Figure A)

1

Slide the aftermarket radio into thecage until it snaps into place. (Figure B)

2

Snap the pocket into the radio hous-ing. (Figure C)

3

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

99-7011 KIT ASSEMBLY

5

A

B

C

ISO MOUNT RADIO PROVISION WITH POCKET

Mount the ISO Brackets to the radiousing the screws supplied with theradio. (Figure A)

1

Slide the radio into the radio housinguntil it snaps into place. (Figure B)

2

Snap the trim plate onto the front ofthe radio housing. (Figure B)

3

Snap the Pocket into the radio housing.(Figure C)

4

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

99-7011 KIT ASSEMBLY

6

DOUBLE DIN RADIO PROVISIONSTACKED ISO MOUNT UNITS PROVISION

Cut and remove the center bar fromthe radio housing. (Figure A)

1

Snap the Double DIN brackets to theinside edge of the radio housing.(Figure B)

2

Slide the Double DIN or stacked ISOmount unit(s) into the bracket/radiohousing assembly and secure theunit(s) to the assembly using thescrews supplied with the unit(s).(Figure C)

3

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

A

B

C

Snap the Double DIN trim plate ontothe front of the radio housing. (Figure C)

4

99-7011 FINAL ASSEMBLY

FINAL ASSEMBLY

(A) Strip wire ends back 1/2"

B) Twist ends together

C) Solder

D) Tape

A

B

C

D

Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)

Re-connect the negative battery terminal and test the unit for proper operation.

Reassemble radio and dash assemblies in reverse order of disassembly.

1

2

3

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and

individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE

12V Ignition / Acc . . . . . . . . . . Red

12V Batt / Memory. . . . . . . . . Yellow

Ground. . . . . . . . . . . . . . . . . . Black*

Power Antenna. . . . . . . . . . . . Blue

Amp Turn-On . . . . . . . . . . . . . Blue / White

Amp Ground. . . . . . . . . . . . . . Black / White

Illumination . . . . . . . . . . . . . . Orange

Dimmer . . . . . . . . . . . . . . . . . Orange / White

Right Front (+) . . . . . . . . . . . . Gray

Right Front (-). . . . . . . . . . . . . Gray/ Black

Left Front (+) . . . . . . . . . . . . . White

Left Front (-). . . . . . . . . . . . . . White / Black

Right Rear (+) . . . . . . . . . . . . Violet

Right Rear (-) . . . . . . . . . . . . . Violet / Black

Left Rear (+) . . . . . . . . . . . . . Green

Left Rear (-) . . . . . . . . . . . . . . Green / Black

*NOTE: When a Black wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.

7

99-7011

NOTES

8

99-7011

NOTES

9

99-7011 INSTRUCTIONS

1-800-221-0932 REV. 05/27/09 © COPYRIGHT 2008-2009 METRA ELECTRONICS CORPORATION INST99-7011

www.metraonline.com